Rescue system for Pogoplug E02 - Best Option?

Greetings, I have a pink Pogoplug E02 which is running Debian from a USB Drive.
It will not boot without the USB installed. Here is the boot log (booting without USB):

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
Initializing devices...
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
Loading envs from usb 0...
** Bad device usb 0 **
Loading envs from usb 1...
** Bad device usb 1 **
Loading envs from usb 2...
** Bad device usb 2 **
Loading envs from usb 3...
** Bad device usb 3 **
Loading envs from ide 0...
** Bad device ide 0 **
Loading envs from ide 1...
** Bad device ide 1 **
Loading envs from ide 2...
** Bad device ide 2 **
Loading envs from ide 3...
** Bad device ide 3 **
Loading envs from mmc 0...
** Bad device mmc 0 **
Loading envs from mmc 1...
** Bad device mmc 1 **
Loading envs from mmc 2...
** Bad device mmc 2 **
Loading envs from mmc 3...
** Bad device mmc 3 **
running scan_disk ...
Scan device usb
device usb 0:1
** Bad device usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide
Unknown command 'ide' - try 'help'
device ide 0:1
** Bad device ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
Scan device mmc
Unknown command 'mmc' - try 'help'
device mmc 0:1
** Bad device mmc 0 **
device mmc 1:1
** Bad device mmc 1 **
device mmc 2:1
** Bad device mmc 2 **
device mmc 3:1
** Bad device mmc 3 **
loading uImage ...
** Bad device usb 0 **
loading uInitrd ...
** Bad device usb 0 **
loading DTB /boot/dts/kirkwood-pogo_e02.dtb ...
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
PogoE02>

I'd like for the Pogoplug to boot some O/S with the USB removed.
I have no image for the original O/S, so that's probably not an option.
Rescue v2 looks good, but I am not sure it is compatible with E02.
What is the recommended rescue systen for E02?
Thanks for these forums and your wisdom (couldn't have gotten this far without help from this site).

See the stickky thread:

OpenWrt (Lede) on Pogo E02 HowTo

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Success! Thanks, so much!