Home
>
Rescue System
>
Topic
Bricked Pogo E02 not loading from USB
Posted by radsfaninlv
|
Bricked Pogo E02 not loading from USB April 17, 2018 09:28PM |
Registered: 10 years ago Posts: 24 |
Hi,
I have bricked my Pogo E02. When plugged in the light flashes green and eventually it flashes yellow. I can only get into it via a serial connection. Here is what I get on boot:
printenv outputs the following:
All help is greatly appreciated!
Thanks.
I have bricked my Pogo E02. When plugged in the light flashes green and eventually it flashes yellow. I can only get into it via a serial connection. Here is what I get on boot:
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
no USB devices available
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
** Bad device usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide
Unknown command 'ide' - try 'help'
device ide 0:1
** Bad device ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
Scan device mmc
Unknown command 'mmc' - try 'help'
device mmc 0:1
** Bad device mmc 0 **
device mmc 1:1
** Bad device mmc 1 **
device mmc 2:1
** Bad device mmc 2 **
device mmc 3:1
** Bad device mmc 3 **
loading uImage ...
** Bad device usb 0 **
loading uInitrd ...
** Bad device usb 0 **
loading DTB /boot/dts/kirkwood-pogo_e02.dtb ...
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
PogoE02>
printenv outputs the following:
printenv arcNumber=3542 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_usb=usb start ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=dd6 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; e scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run i; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; i usb_ready_retry=15 Environment size: 3127/131068 bytes
All help is greatly appreciated!
Thanks.
|
Re: Bricked Pogo E02 not loading from USB April 18, 2018 06:03PM |
Registered: 10 years ago Posts: 24 |
|
Re: Bricked Pogo E02 not loading from USB April 19, 2018 04:58AM |
Registered: 10 years ago Posts: 94 |
|
Re: Bricked Pogo E02 not loading from USB April 19, 2018 05:01AM |
Admin Registered: 13 years ago Posts: 18,900 |
@radsfaninlv ,
What joerg_999 said
See your boot log
Try with a different USB thumb drive.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
What joerg_999 said
> your Pogo and boot-envs seems to be ok, bot > not your USB Stick
See your boot log
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
no USB devices
Try with a different USB thumb drive.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 19, 2018 03:03PM |
Registered: 10 years ago Posts: 24 |
I can't get the uboot to see the any usb stick.
Here is what I get when the pogo boots up:
Here is what I get when the pogo boots up:
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... EHCI timed out on TD - token=0x80008c80
2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x200000
Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-08-10 19:57:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1977716 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #44 Mon Aug 10 12:57:36 PDT 2009
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 252K data, 120K init)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] NET: Registered protocol family 16
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e8000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] INTER_REGS ....base f1000000, size 1MB
[ 0.250000] NFLASH_CS ....base fa000000, size 2MB
[ 0.250000] SPI_CS ....base f4000000, size 16MB
[ 0.250000] BOOT_ROM_CS ....no such
[ 0.250000] DEV_BOOTCS ....no such
[ 0.250000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.250000]
[ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.250000]
[ 0.250000] Detected Tclk 200000000 and SysClk 400000000
[ 0.250000] MV Buttons Device Load
[ 0.250000] Marvell USB EHCI Host controller #0: c0650600
[ 0.750000] PEX0 interface detected no Link.
[ 0.750000] PCI: bus0: Fast back to back transfers enabled
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.760000] Time: kw_clocksource clocksource has been installed.
[ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.850000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.850000] TCP reno registered
[ 0.880000] RTC has been updated!!!
[ 0.880000] RTC registered
[ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.880000] o RAID 5 Xor calculation
[ 0.880000] o kernel memcpy
[ 0.880000] o kenrel memzero
[ 0.880000] Number of XOR engines to use: 4
[ 0.880000] cesadev_init(c00116b4)
[ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.880000] MV Buttons Driver Load
[ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.880000] squashfs: LZMA suppport for slax.org by jro
[ 0.880000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.880000] io scheduler noop registered
[ 0.880000] io scheduler anticipatory registered (default)
[ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.910000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 0.920000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.930000] Loading Marvell Ethernet Driver:
[ 0.940000] o Cached descriptors in DRAM
[ 0.940000] o DRAM SW cache-coherency
[ 0.940000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.950000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.950000] o TCP segmentation offload enabled
[ 0.960000] o Receive checksum offload enabled
[ 0.960000] o Transmit checksum offload enabled
[ 0.970000] o Network Fast Processing (Routing) supported
[ 0.970000] o Driver ERROR statistics enabled
[ 0.980000] o Driver INFO statistics enabled
[ 0.980000] o Proc tool API enabled
[ 0.990000] o Rx descripors: q0=128
[ 0.990000] o Tx descripors: q0=532
[ 0.990000] o Loading network interface(s):
[ 1.000000] o eth0, ifindex = 1, GbE port = 0
[ 1.010000] o eth1, ifindex = 2, GbE port = 1
[ 1.010000]
[ 1.010000] mvFpRuleDb (cf8c2000): 2048 entries, 8192 bytes
[ 1.020000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.030000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.030000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.040000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.040000]
[ 1.040000] Warning Sata is Powered Off
[ 1.050000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.060000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.070000] Scanning device for bad blocks
[ 1.120000] Using static partition definition
[ 1.120000] Creating 4 MTD partitions on "nand_mtd":
[ 1.130000] 0x00000000-0x00100000 : "u-boot"
[ 1.130000] 0x00100000-0x00500000 : "uImage"
[ 1.140000] 0x00500000-0x02500000 : "root"
[ 1.140000] 0x02500000-0x08000000 : "data"
[ 1.150000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.150000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.190000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.210000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.210000] usb usb1: configuration #1 chosen from 1 choice
[ 1.220000] hub 1-0:1.0: USB hub found
[ 1.220000] hub 1-0:1.0: 1 port detected
[ 1.340000] USB Universal Host Controller Interface driver v3.0
[ 1.620000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.740000] usb 1-1: device descriptor read/64, error -71
[ 1.970000] usb 1-1: device descriptor read/64, error -71
[ 2.200000] usb 1-1: new high speed USB device using ehci_marvell and address 3
[ 2.320000] usb 1-1: device descriptor read/64, error -71
[ 2.550000] usb 1-1: device descriptor read/64, error -71
[ 2.780000] usb 1-1: new high speed USB device using ehci_marvell and address 4
[ 3.200000] usb 1-1: device not accepting address 4, error -71
[ 3.320000] usb 1-1: new high speed USB device using ehci_marvell and address 5
[ 3.740000] usb 1-1: device not accepting address 5, error -71
[ 3.740000] usbcore: registered new interface driver usblp
[ 3.750000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 3.750000] Initializing USB Mass Storage driver...
[ 3.760000] usbcore: registered new interface driver usb-storage
[ 3.760000] USB Mass Storage support registered.
[ 3.770000] mice: PS/2 mouse device common for all mice
[ 3.770000] i2c /dev entries driver
[ 3.780000] Linux telephony interface: v1.00
[ 3.780000] md: linear personality registered for level -1
[ 3.790000] md: raid0 personality registered for level 0
[ 3.790000] md: raid1 personality registered for level 1
[ 3.970000] raid6: int32x1 97 MB/s
[ 4.140000] raid6: int32x2 114 MB/s
[ 4.310000] raid6: int32x4 122 MB/s
[ 4.480000] raid6: int32x8 111 MB/s
[ 4.480000] raid6: using algorithm int32x4 (122 MB/s)
[ 4.480000] md: raid6 personality registered for level 6
[ 4.490000] md: raid5 personality registered for level 5
[ 4.500000] md: raid4 personality registered for level 4
[ 4.500000] raid5: measuring checksumming speed
[ 4.550000] arm4regs : 1084.000 MB/sec
[ 4.600000] 8regs : 754.800 MB/sec
[ 4.650000] 32regs : 899.600 MB/sec
[ 4.650000] raid5: using function: arm4regs (1084.000 MB/sec)
[ 4.660000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 4.660000] dm_crypt using the OCF package.
[ 4.670000] sdhci: Secure Digital Host Controller Interface driver
[ 4.670000] sdhci: Copyright(c) Pierre Ossman
[ 4.680000] usbcore: registered new interface driver usbhid
[ 4.680000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 4.690000] TCP cubic registered
[ 4.690000] NET: Registered protocol family 1
[ 4.700000] NET: Registered protocol family 17
[ 4.700000] md: Autodetecting RAID arrays.
[ 4.710000] md: autorun ...
[ 4.710000] md: ... autorun DONE.
[ 7.930000] Empty flash at 0x009ac208 ends at 0x009ac800
[ 8.750000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 8.760000] Freeing init memory: 120K
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 264, tty '': '/etc/init.d/rcS'
[ 10.880000] eth0: link down
[ 10.880000] eth0: started
udhcpc (v1.7.0) started
HWADDR 00 0x25 0x31 0x04 0xa2 0x2f
PIP0 162
PIP1 47
Sending discover...
Sending discover...
[ 15.600000] eth0: link up, full duplex, speed 1 Gbps
Sending discover...
Sending select for 192.168.1.123...
Lease of 192.168.1.123 obtained, lease time 86400
HWADDR 00 0x25 0x31 0x04 0xa2 0x2f
PIP0 162
PIP1 47
|
Re: Bricked Pogo E02 not loading from USB April 19, 2018 05:19PM |
Admin Registered: 13 years ago Posts: 18,900 |
radsfaninlv,
Your u-boot is an older version, so it has problem dealing with a not-perfect USB drive.
But this happened a lot in the past. And we just try a different USB thumb drive to make it work. Also try plugging into a different USB port. If you have Sandisk brand USB stick, use that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Your u-boot is an older version, so it has problem dealing with a not-perfect USB drive.
Quote
>
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
scanning bus for devices... EHCI timed out on TD -
> token=0x80008c80
But this happened a lot in the past. And we just try a different USB thumb drive to make it work. Also try plugging into a different USB port. If you have Sandisk brand USB stick, use that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 20, 2018 05:22PM |
Registered: 10 years ago Posts: 24 |
|
Re: Bricked Pogo E02 not loading from USB April 22, 2018 06:59AM |
Registered: 10 years ago Posts: 94 |
why not upgrading to the latest uboot + uboot-envs ? (most of your problems will gone..)
if you have serial console it is very easy to do that:
and you will be happy
joerg_999
Edited 4 time(s). Last edit at 04/26/2018 03:08AM by joerg_999.
if you have serial console it is very easy to do that:
# on Windows PC download tftp.zip, or use my dropbox downloadlink with all the needed files. (https://tftpd64.codeplex.com/downloads/get/1632548) # on Windows PC make a directory c:/TFTP and put all in there # unpack und start tftp # the kwb files and the enviroment.img file should also be in c:/TFTP # find your IP on the Windows PC: cmd ipconfig -------------------------------------------------------------------------------- # on Pogo @console set ip's: # set tftp-server ip setenv serverip <ip_from_ipconfig> # setenv serverip 192.168.1.10 # read out mac adresse from Pogo and note here <ethaddr>, you will need it later: printenv ethaddr ##. TFTP bootng - this works: #set Pogo/goflex net ip, use any adress in the same range like serverip setenv ipaddr 192.168.1.200 # test for bad nand-blocks nand info nand bad # if an error appears and the count is bigger than "0x00100000" there is no problem to flash!! ------------------------------------------------------------------------------------------------------------------------------------- # original bodhi uboot.2017.07-tld-1.pogo_e02.mtd0.kwb # for Pogo E02 ------------------------------------------------------------------------------------------------------------------------------------- tftpboot 0x800000 uboot.2017.07-tld-1.pogo_e02.mtd0.kwb nand erase 0 0x80000 nand write.e 0x800000 0x0 0x80000 reset # stop booting and continue with the envs ------------------------------------------------------------------------------------------------------------------------------------- # original bodhi uboot-envs uboot.2016.05-tld-1.environment.img # universal for all kirkwoods ------------------------------------------------------------------------------------------------------------------------------------- tftpboot 0x800000 uboot.2016.05-tld-1.environment.img nand erase 0xc0000 0x20000 nand write.e 0x800000 0xc0000 0x20000 setenv ethaddr <ethaddr> # uboot-env changes for Pogo E02: setenv arcNumber 3542 setenv machid dd6 setenv dtb_file /boot/dts/kirkwood-pogo_e02.dtb saveenv reset # ready you are done!Links from my Dropbox: POGO E02 tftp_Bootloader change
and you will be happy
joerg_999
Edited 4 time(s). Last edit at 04/26/2018 03:08AM by joerg_999.
|
Re: Bricked Pogo E02 not loading from USB April 25, 2018 03:34AM |
Registered: 10 years ago Posts: 24 |
|
Re: Bricked Pogo E02 not loading from USB April 25, 2018 11:09AM |
Registered: 10 years ago Posts: 24 |
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 03:06AM |
Registered: 10 years ago Posts: 94 |
radsfaninlv Wrote:
-------------------------------------------------------
> I get the following for nand bad:
>
>
> No number at all
perfect, you can continue the instructions
(it means you have no bad blocks at all)
--joerg_999
Edited 1 time(s). Last edit at 04/26/2018 03:09AM by joerg_999.
-------------------------------------------------------
> I get the following for nand bad:
>
>
> nand bad > > Device 0 bad blocks: > >>
> No number at all
perfect, you can continue the instructions
(it means you have no bad blocks at all)
--joerg_999
Edited 1 time(s). Last edit at 04/26/2018 03:09AM by joerg_999.
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 12:52PM |
Registered: 10 years ago Posts: 24 |
Still not working. Here is what happens when I try to boot (with usb flash drive or without it): BTW, thank you for the help you have provided.
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 5
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 4
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 3
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 2
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 1
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 0
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=3", size 91 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 728, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 0
ubi0: available PEBs: 704, total reserved PEBs: 24, PEBs reserved for bad PEB handling: 20
Error reading superblock on volume 'rootfs' errno=-22!
ubifsmount - mount UBIFS volume
Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume
** Bad device usb 0 **
** Bad device usb 1 **
** Bad device usb 2 **
** Bad device usb 3 **
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x200000
Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-08-10 19:57:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1977716 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #44 Mon Aug 10 12:57:36 PDT 2009
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 252K data, 120K init)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] NET: Registered protocol family 16
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e8000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] INTER_REGS ....base f1000000, size 1MB
[ 0.250000] NFLASH_CS ....base fa000000, size 2MB
[ 0.250000] SPI_CS ....base f4000000, size 16MB
[ 0.250000] BOOT_ROM_CS ....no such
[ 0.250000] DEV_BOOTCS ....no such
[ 0.250000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.250000]
[ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.250000]
[ 0.250000] Detected Tclk 200000000 and SysClk 400000000
[ 0.250000] MV Buttons Device Load
[ 0.250000] Marvell USB EHCI Host controller #0: c0650600
[ 0.750000] PEX0 interface detected no Link.
[ 0.750000] PCI: bus0: Fast back to back transfers enabled
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.760000] Time: kw_clocksource clocksource has been installed.
[ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.850000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.850000] TCP reno registered
[ 0.880000] RTC has been updated!!!
[ 0.880000] RTC registered
[ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.880000] o RAID 5 Xor calculation
[ 0.880000] o kernel memcpy
[ 0.880000] o kenrel memzero
[ 0.880000] Number of XOR engines to use: 4
[ 0.880000] cesadev_init(c00116b4)
[ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.880000] MV Buttons Driver Load
[ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.880000] squashfs: LZMA suppport for slax.org by jro
[ 0.880000] JFFS2 version 2.2. (NAND) ���� 2001-2006 Red Hat, Inc.
[ 0.880000] io scheduler noop registered
[ 0.880000] io scheduler anticipatory registered (default)
[ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.910000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 0.920000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.930000] Loading Marvell Ethernet Driver:
[ 0.940000] o Cached descriptors in DRAM
[ 0.940000] o DRAM SW cache-coherency
[ 0.940000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.950000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.950000] o TCP segmentation offload enabled
[ 0.960000] o Receive checksum offload enabled
[ 0.960000] o Transmit checksum offload enabled
[ 0.970000] o Network Fast Processing (Routing) supported
[ 0.970000] o Driver ERROR statistics enabled
[ 0.980000] o Driver INFO statistics enabled
[ 0.980000] o Proc tool API enabled
[ 0.990000] o Rx descripors: q0=128
[ 0.990000] o Tx descripors: q0=532
[ 0.990000] o Loading network interface(s):
[ 1.000000] o eth0, ifindex = 1, GbE port = 0
[ 1.010000] o eth1, ifindex = 2, GbE port = 1
[ 1.010000]
[ 1.010000] mvFpRuleDb (cf8c2000): 2048 entries, 8192 bytes
[ 1.020000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.030000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.030000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.040000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.040000]
[ 1.040000] Warning Sata is Powered Off
[ 1.050000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.060000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.070000] Scanning device for bad blocks
[ 1.120000] Using static partition definition
[ 1.120000] Creating 4 MTD partitions on "nand_mtd":
[ 1.130000] 0x00000000-0x00100000 : "u-boot"
[ 1.130000] 0x00100000-0x00500000 : "uImage"
[ 1.140000] 0x00500000-0x02500000 : "root"
[ 1.140000] 0x02500000-0x08000000 : "data"
[ 1.150000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.150000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.190000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.210000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.210000] usb usb1: configuration #1 chosen from 1 choice
[ 1.220000] hub 1-0:1.0: USB hub found
[ 1.220000] hub 1-0:1.0: 1 port detected
[ 1.340000] USB Universal Host Controller Interface driver v3.0
[ 1.620000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.740000] usb 1-1: device descriptor read/64, error -71
[ 1.970000] usb 1-1: device descriptor read/64, error -71
[ 2.200000] usb 1-1: new high speed USB device using ehci_marvell and address 3
[ 2.320000] usb 1-1: device descriptor read/64, error -71
[ 2.550000] usb 1-1: device descriptor read/64, error -71
[ 2.780000] usb 1-1: new high speed USB device using ehci_marvell and address 4
[ 3.200000] usb 1-1: device not accepting address 4, error -71
[ 3.320000] usb 1-1: new high speed USB device using ehci_marvell and address 5
[ 3.740000] usb 1-1: device not accepting address 5, error -71
[ 3.740000] usbcore: registered new interface driver usblp
[ 3.750000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 3.750000] Initializing USB Mass Storage driver...
[ 3.760000] usbcore: registered new interface driver usb-storage
[ 3.760000] USB Mass Storage support registered.
[ 3.770000] mice: PS/2 mouse device common for all mice
[ 3.770000] i2c /dev entries driver
[ 3.780000] Linux telephony interface: v1.00
[ 3.780000] md: linear personality registered for level -1
[ 3.790000] md: raid0 personality registered for level 0
[ 3.790000] md: raid1 personality registered for level 1
[ 3.970000] raid6: int32x1 97 MB/s
[ 4.140000] raid6: int32x2 114 MB/s
[ 4.310000] raid6: int32x4 122 MB/s
[ 4.480000] raid6: int32x8 111 MB/s
[ 4.480000] raid6: using algorithm int32x4 (122 MB/s)
[ 4.480000] md: raid6 personality registered for level 6
[ 4.490000] md: raid5 personality registered for level 5
[ 4.500000] md: raid4 personality registered for level 4
[ 4.500000] raid5: measuring checksumming speed
[ 4.550000] arm4regs : 1084.000 MB/sec
[ 4.600000] 8regs : 754.800 MB/sec
[ 4.650000] 32regs : 900.000 MB/sec
[ 4.650000] raid5: using function: arm4regs (1084.000 MB/sec)
[ 4.660000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 4.660000] dm_crypt using the OCF package.
[ 4.670000] sdhci: Secure Digital Host Controller Interface driver
[ 4.670000] sdhci: Copyright(c) Pierre Ossman
[ 4.680000] usbcore: registered new interface driver usbhid
[ 4.680000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 4.690000] TCP cubic registered
[ 4.690000] NET: Registered protocol family 1
[ 4.700000] NET: Registered protocol family 17
[ 4.700000] md: Autodetecting RAID arrays.
[ 4.710000] md: autorun ...
[ 4.710000] md: ... autorun DONE.
[ 7.930000] Empty flash at 0x009ac208 ends at 0x009ac800
[ 8.750000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 8.760000] Freeing init memory: 120K
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 264, tty '': '/etc/init.d/rcS'
[ 10.880000] eth0: started
udhcpc (v1.7.0) started
HWADDR 00 0x25 0x31 0x04 0xa2 0x2f
PIP0 162
PIP1 47
Sending discover...
Sending discover...
Sending discover...
HWADDR 00 0x25 0x31 0x04 0xa2 0x2f
PIP0 162
PIP1 47
Unexpected Argument: leasefail
interface=eth0
PATH=/sbin:/usr/sbin:/bin:/usr/bin
PWD=/
SHLVL=1
HOME=/
_=/bin/printenv
No lease, forking to background
starting pid 309, tty '': '/bin/sh'
-sh-3.2#
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 02:57PM |
Admin Registered: 13 years ago Posts: 18,900 |
radsfaninlv,
The boot without USB was OK. It booted into stock OS.
The boot with the USB drive still not regcognize the drive
> > scanning bus 0 for devices... EHCI timed out on TD
> - token=0x80008c80
> EHCI timed out on TD - token=0x80a88
What brand, model, capacity is this USB drive?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
The boot without USB was OK. It booted into stock OS.
Quote
-sh-3.2#
The boot with the USB drive still not regcognize the drive
> > scanning bus 0 for devices... EHCI timed out on TD
> - token=0x80008c80
> EHCI timed out on TD - token=0x80a88
What brand, model, capacity is this USB drive?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 03:40PM |
Registered: 10 years ago Posts: 24 |
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 04:56PM |
Admin Registered: 13 years ago Posts: 18,900 |
radsfaninlv,
> SanDisk Cruzer Fit CZ33 16GB USB 2.0 Low-Profile
> Flash Drive- SDCZ33-016G-B35
That's odd. I've been using this exact model for quite a while and never have the "EHCI timed out on TD" error. With that said, the Pogo E02 u-boot-2017.07-tld-1 supposes to have fixed this error anyway.
So I think is your problem is related to:
Because even with "EHCI timed out on TD", the "unable to get device descriptor" error should not occur on a good USB drive.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> SanDisk Cruzer Fit CZ33 16GB USB 2.0 Low-Profile
> Flash Drive- SDCZ33-016G-B35
That's odd. I've been using this exact model for quite a while and never have the "EHCI timed out on TD" error. With that said, the Pogo E02 u-boot-2017.07-tld-1 supposes to have fixed this error anyway.
So I think is your problem is related to:
unable to get device descriptor (error=-1) retry: 5
Because even with "EHCI timed out on TD", the "unable to get device descriptor" error should not occur on a good USB drive.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 05:08PM |
Admin Registered: 13 years ago Posts: 18,900 |
radsfaninlv,
One other things is not right. Your log should show the message
At serial console, print out this env:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
One other things is not right. Your log should show the message
Use USB retry period from the environment: 15 second(s)But it did not.
At serial console, print out this env:
printenv usb_ready_retry
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 05:18PM |
Registered: 10 years ago Posts: 24 |
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 05:33PM |
Admin Registered: 13 years ago Posts: 18,900 |
radsfaninlv Wrote:
-------------------------------------------------------
>
> It prints out nothing
"In serial console" means: at this point, interrupt count down, and execute printenv.
And please post the entire log until this point.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/26/2018 05:34PM by bodhi.
-------------------------------------------------------
>
> -sh-3.2# printenv usb_ready_retry > -sh-3.2# >>
> It prints out nothing
"In serial console" means: at this point, interrupt count down, and execute printenv.
Hit any key to stop autoboot: 0
And please post the entire log until this point.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/26/2018 05:34PM by bodhi.
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 05:52PM |
Registered: 10 years ago Posts: 24 |
Ok. Here you go:
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 PogoE02> printenv usb_ready_retry ## Error: "usb_ready_retry" not defined PogoE02>
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 09:26PM |
Admin Registered: 13 years ago Posts: 18,900 |
radsfaninlv Wrote:
-------------------------------------------------------
> Ok. Here you go:
>
>
That means your uboot envs are messed up. Let’s see what they are.
Power up, interrupt serial console at count down again, and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Ok. Here you go:
>
>
> U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 > -0700) > Pogo E02 > > SoC: Kirkwood 88F6281_A0 > DRAM: 256 MiB > WARNING: Caches not enabled > NAND: 128 MiB > In: serial > Out: serial > Err: serial > Net: egiga0 > Hit any key to stop autoboot: 0 > PogoE02> printenv usb_ready_retry > ## Error: "usb_ready_retry" not defined > PogoE02> > >
That means your uboot envs are messed up. Let’s see what they are.
Power up, interrupt serial console at count down again, and
printenv
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 26, 2018 11:41PM |
Registered: 10 years ago Posts: 24 |
bodhi Wrote:
-------------------------------------------------------
> radsfaninlv Wrote:
> -------------------------------------------------------
> > Ok. Here you go:
> >
> >
> That means your uboot envs are messed up. Let’s
> see what they are.
>
> Power up, interrupt serial console at count down
> again, and
>
>
-------------------------------------------------------
> radsfaninlv Wrote:
> -------------------------------------------------------
> > Ok. Here you go:
> >
> >
> > U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 > > -0700) > > Pogo E02 > > > > SoC: Kirkwood 88F6281_A0 > > DRAM: 256 MiB > > WARNING: Caches not enabled > > NAND: 128 MiB > > In: serial > > Out: serial > > Err: serial > > Net: egiga0 > > Hit any key to stop autoboot: 0 > > PogoE02> printenv usb_ready_retry > > ## Error: "usb_ready_retry" not defined > > PogoE02> > > > >>
> That means your uboot envs are messed up. Let’s
> see what they are.
>
> Power up, interrupt serial console at count down
> again, and
>
>
printenv
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 PogoE02> printenv arcNumber=3542 baudrate=115200 bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset bootdelay=3 console=ttyS0,115200 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 fileaddr=800000 filesize=20000 force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ipaddr=192.168.1.123 led_error=orange blinking led_exit=green off led_init=green blinking machid=dd6 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params serverip=192.168.1.124 stderr=serial stdin=serial stdout=serial ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_init=run usb_scan usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext3 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_scan_list=1 2 3 4 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params Environment size: 2481/131068 bytes
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 01:17AM |
Admin Registered: 13 years ago Posts: 18,900 |
That's a really old set of u-boot envs (2011-2012). Not for u-boot-2017.07-tld-1.
But let see if it helps to do this. Power up, interrupt serial console at count down again, and
See if the USB drive is intialized OK.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/27/2018 01:22AM by bodhi.
But let see if it helps to do this. Power up, interrupt serial console at count down again, and
setenv usb_ready_retry 30 usb reset
See if the USB drive is intialized OK.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/27/2018 01:22AM by bodhi.
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 07:47AM |
Registered: 10 years ago Posts: 24 |
The USB is still not recognized:
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02> setenv usb_ready_retry 30
PogoE02> usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 5
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 4
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 3
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 2
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 1
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 0
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 05:44PM |
Admin Registered: 13 years ago Posts: 18,900 |
radsfaninlv Wrote:
-------------------------------------------------------
> The USB is still not recognized:
>
>
Try
And then restart u-boot
And then
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> The USB is still not recognized:
>
>
> U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 > -0700) > Pogo E02 > > SoC: Kirkwood 88F6281_A0 > DRAM: 256 MiB > WARNING: Caches not enabled > NAND: 128 MiB > In: serial > Out: serial > Err: serial > Net: egiga0 > Hit any key to stop autoboot: 0 > PogoE02> setenv usb_ready_retry 30 > PogoE02> usb reset > resetting USB... > USB0: USB EHCI 1.00 > scanning bus 0 for devices... EHCI timed out on TD > - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 5 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 4 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 3 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 2 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 1 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 0 > 1 USB Device(s) found > scanning usb for storage devices... 0 > Storage Device(s) found > >
Try
setenv usb_ready_retry 30 saveenv
And then restart u-boot
reset
And then
usb reset
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 07:22PM |
Registered: 10 years ago Posts: 24 |
Still no good.
usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 5
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 4
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 3
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 2
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 1
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 0
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 07:24PM |
Admin Registered: 13 years ago Posts: 18,900 |
radsfaninlv Wrote:
-------------------------------------------------------
> Still no good.
>
>
Please post full serial log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Still no good.
>
>
> usb reset > resetting USB... > USB0: USB EHCI 1.00 > scanning bus 0 for devices... EHCI timed out on TD > - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 5 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 4 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 3 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 2 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 1 > EHCI timed out on TD - token=0x80008c80 > EHCI timed out on TD - token=0x80a88 > unable to get device descriptor (error=-1) retry: > 0 > 1 USB Device(s) found > scanning usb for storage devices... 0 > Storage Device(s) found > >
Please post full serial log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 07:30PM |
Registered: 10 years ago Posts: 24 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02> reset
resetting ...
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 5
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 4
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 3
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 2
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 1
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 0
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=3", size 91 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 728, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 0
ubi0: available PEBs: 704, total reserved PEBs: 24, PEBs reserved for bad PEB handling: 20
Error reading superblock on volume 'rootfs' errno=-22!
ubifsmount - mount UBIFS volume
Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume
** Bad device usb 0 **
** Bad device usb 1 **
** Bad device usb 2 **
** Bad device usb 3 **
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
CE>> reset
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 5
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 4
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 3
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 2
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 1
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 0
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=3", size 91 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 728, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 0
ubi0: available PEBs: 704, total reserved PEBs: 24, PEBs reserved for bad PEB handling: 20
Error reading superblock on volume 'rootfs' errno=-22!
ubifsmount - mount UBIFS volume
Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume
** Bad device usb 0 **
** Bad device usb 1 **
** Bad device usb 2 **
** Bad device usb 3 **
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x200000
Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-08-10 19:57:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1977716 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #44 Mon Aug 10 12:57:36 PDT 2009
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 252K data, 120K init)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] NET: Registered protocol family 16
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e8000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] INTER_REGS ....base f1000000, size 1MB
[ 0.250000] NFLASH_CS ....base fa000000, size 2MB
[ 0.250000] SPI_CS ....base f4000000, size 16MB
[ 0.250000] BOOT_ROM_CS ....no such
[ 0.250000] DEV_BOOTCS ....no such
[ 0.250000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.250000]
[ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.250000]
[ 0.250000] Detected Tclk 200000000 and SysClk 400000000
[ 0.250000] MV Buttons Device Load
[ 0.250000] Marvell USB EHCI Host controller #0: c0650600
[ 0.750000] PEX0 interface detected no Link.
[ 0.750000] PCI: bus0: Fast back to back transfers enabled
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.760000] Time: kw_clocksource clocksource has been installed.
[ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.850000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.850000] TCP reno registered
[ 0.880000] RTC has been updated!!!
[ 0.880000] RTC registered
[ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.880000] o RAID 5 Xor calculation
[ 0.880000] o kernel memcpy
[ 0.880000] o kenrel memzero
[ 0.880000] Number of XOR engines to use: 4
[ 0.880000] cesadev_init(c00116b4)
[ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.880000] MV Buttons Driver Load
[ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.880000] squashfs: LZMA suppport for slax.org by jro
[ 0.880000] JFFS2 version 2.2. (NAND) ���� 2001-2006 Red Hat, Inc.
[ 0.880000] io scheduler noop registered
[ 0.880000] io scheduler anticipatory registered (default)
[ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.910000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 0.920000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.930000] Loading Marvell Ethernet Driver:
[ 0.940000] o Cached descriptors in DRAM
[ 0.940000] o DRAM SW cache-coherency
[ 0.940000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.950000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.950000] o TCP segmentation offload enabled
[ 0.960000] o Receive checksum offload enabled
[ 0.960000] o Transmit checksum offload enabled
[ 0.970000] o Network Fast Processing (Routing) supported
[ 0.970000] o Driver ERROR statistics enabled
[ 0.980000] o Driver INFO statistics enabled
[ 0.980000] o Proc tool API enabled
[ 0.990000] o Rx descripors: q0=128
[ 0.990000] o Tx descripors: q0=532
[ 0.990000] o Loading network interface(s):
[ 1.000000] o eth0, ifindex = 1, GbE port = 0
[ 1.010000] o eth1, ifindex = 2, GbE port = 1
[ 1.010000]
[ 1.010000] mvFpRuleDb (cf8c2000): 2048 entries, 8192 bytes
[ 1.020000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.030000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.030000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.040000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.040000]
[ 1.040000] Warning Sata is Powered Off
[ 1.050000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.060000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.070000] Scanning device for bad blocks
[ 1.120000] Using static partition definition
[ 1.120000] Creating 4 MTD partitions on "nand_mtd":
[ 1.130000] 0x00000000-0x00100000 : "u-boot"
[ 1.130000] 0x00100000-0x00500000 : "uImage"
[ 1.140000] 0x00500000-0x02500000 : "root"
[ 1.140000] 0x02500000-0x08000000 : "data"
[ 1.150000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.150000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.190000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.210000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.210000] usb usb1: configuration #1 chosen from 1 choice
[ 1.220000] hub 1-0:1.0: USB hub found
[ 1.220000] hub 1-0:1.0: 1 port detected
[ 1.340000] USB Universal Host Controller Interface driver v3.0
[ 1.620000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.740000] usb 1-1: device descriptor read/64, error -71
[ 1.970000] usb 1-1: device descriptor read/64, error -71
[ 2.200000] usb 1-1: new high speed USB device using ehci_marvell and address 3
[ 2.320000] usb 1-1: device descriptor read/64, error -71
[ 2.550000] usb 1-1: device descriptor read/64, error -71
[ 2.780000] usb 1-1: new high speed USB device using ehci_marvell and address 4
[ 3.200000] usb 1-1: device not accepting address 4, error -71
[ 3.320000] usb 1-1: new high speed USB device using ehci_marvell and address 5
[ 3.740000] usb 1-1: device not accepting address 5, error -71
[ 3.740000] usbcore: registered new interface driver usblp
[ 3.750000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 3.750000] Initializing USB Mass Storage driver...
[ 3.760000] usbcore: registered new interface driver usb-storage
[ 3.760000] USB Mass Storage support registered.
[ 3.770000] mice: PS/2 mouse device common for all mice
[ 3.770000] i2c /dev entries driver
[ 3.780000] Linux telephony interface: v1.00
[ 3.780000] md: linear personality registered for level -1
[ 3.790000] md: raid0 personality registered for level 0
[ 3.790000] md: raid1 personality registered for level 1
[ 3.970000] raid6: int32x1 97 MB/s
[ 4.140000] raid6: int32x2 114 MB/s
[ 4.310000] raid6: int32x4 122 MB/s
[ 4.480000] raid6: int32x8 110 MB/s
[ 4.480000] raid6: using algorithm int32x4 (122 MB/s)
[ 4.480000] md: raid6 personality registered for level 6
[ 4.490000] md: raid5 personality registered for level 5
[ 4.490000] md: raid4 personality registered for level 4
[ 4.500000] raid5: measuring checksumming speed
[ 4.550000] arm4regs : 1084.000 MB/sec
[ 4.600000] 8regs : 754.800 MB/sec
[ 4.650000] 32regs : 890.400 MB/sec
[ 4.650000] raid5: using function: arm4regs (1084.000 MB/sec)
[ 4.660000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 4.660000] dm_crypt using the OCF package.
[ 4.670000] sdhci: Secure Digital Host Controller Interface driver
[ 4.670000] sdhci: Copyright(c) Pierre Ossman
[ 4.680000] usbcore: registered new interface driver usbhid
[ 4.680000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 4.690000] TCP cubic registered
[ 4.690000] NET: Registered protocol family 1
[ 4.700000] NET: Registered protocol family 17
[ 4.700000] md: Autodetecting RAID arrays.
[ 4.710000] md: autorun ...
[ 4.710000] md: ... autorun DONE.
[ 7.930000] Empty flash at 0x009ac208 ends at 0x009ac800
[ 8.750000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 8.760000] Freeing init memory: 120K
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 264, tty '': '/etc/init.d/rcS'
[ 10.880000] eth0: link down
[ 10.880000] eth0: started
udhcpc (v1.7.0) started
HWADDR 00 0x25 0x31 0x04 0xa2 0x2f
PIP0 162
PIP1 47
Sending discover...
[ 12.570000] eth0: link up, full duplex, speed 100 Mbps
Sending discover...
Sending select for 192.168.1.125...
Lease of 192.168.1.125 obtained, lease time 86400
HWADDR 00 0x25 0x31 0x04 0xa2 0x2f
PIP0 162
PIP1 47
eth0 Link encap:Ethernet HWaddr 00:25:31:04:A2:2F
inet addr:192.168.1.125 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:868 (868.0 B) TX bytes:1180 (1.1 KiB)
Interrupt:11
eth0:0 Link encap:Ethernet HWaddr 00:25:31:04:A2:2F
inet addr:169.254.162.47 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:11
starting pid 316, tty '': '/bin/sh'
-sh-3.2#
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 08:22PM |
Admin Registered: 13 years ago Posts: 18,900 |
Something very strange. Please try,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
reset printenv usb reset
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 08:43PM |
Registered: 7 years ago Posts: 373 |
|
Re: Bricked Pogo E02 not loading from USB April 27, 2018 08:52PM |
Admin Registered: 13 years ago Posts: 18,900 |
daviddyer Wrote:
-------------------------------------------------------
> Also, if possible, open the PogoE02 and check the
> power supply (!!! Be careful of the high
> voltage!), or try to power it with a separate
> power supply.
Absolutely Yes, thats the next step after we see the log :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/27/2018 08:52PM by bodhi.
-------------------------------------------------------
> Also, if possible, open the PogoE02 and check the
> power supply (!!! Be careful of the high
> voltage!), or try to power it with a separate
> power supply.
Absolutely Yes, thats the next step after we see the log :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/27/2018 08:52PM by bodhi.
