Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread
Posted by JeffS
|
Re: Best Pogoplug to buy March 13, 2017 06:37PM |
Admin Registered: 13 years ago Posts: 18,585 |
|
Re: Best Pogoplug to buy March 13, 2017 06:51PM |
Registered: 9 years ago Posts: 1,516 |
|
Re: Best Pogoplug to buy March 13, 2017 06:52PM |
Admin Registered: 13 years ago Posts: 18,585 |
JoeyPogoPlugE02 Wrote:
-------------------------------------------------------
> It appears not to boot with a USB stick in one of
> the 3.0 ports. Working on obvious troubleshooting,
> back in a bit...
>
> Bodhi, when you say have nothing on the USB stick,
> do you mean format it "unformatted"? As is you can
> see it's a 32GB stick formatted Fat32.
That's expected. Your uboot envs are old :) but it could be fixed later. For now boot without the UltraFit. And plug it in after.
It is fine now. But we want to format it with ext4:
mkfs.ext4 -L JoeyUSB3 /dev/sdb1
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/13/2017 06:55PM by bodhi.
-------------------------------------------------------
> It appears not to boot with a USB stick in one of
> the 3.0 ports. Working on obvious troubleshooting,
> back in a bit...
>
> Bodhi, when you say have nothing on the USB stick,
> do you mean format it "unformatted"? As is you can
> see it's a 32GB stick formatted Fat32.
That's expected. Your uboot envs are old :) but it could be fixed later. For now boot without the UltraFit. And plug it in after.
It is fine now. But we want to format it with ext4:
mkfs.ext4 -L JoeyUSB3 /dev/sdb1
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/13/2017 06:55PM by bodhi.
|
Re: Best Pogoplug to buy March 13, 2017 06:58PM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
Please run lsusb again and post output here;
lsusb -vvv
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Please run lsusb again and post output here;
lsusb -vvv
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Best Pogoplug to buy March 13, 2017 07:28PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> It is fine now. But we want to format it with ext4:
>
> mkfs.ext4 -L JoeyUSB3 /dev/sdb1
It's either taking a while or stalled. I'll wait a little bit. Worse comes to worse I could format it Ext4 w 4k blocks from Partition Wizard on ThinClient.
bodhi Wrote:
-------------------------------------------------------
> Joey,
>
> Please run lsusb again and post output here;
>
> lsusb -vvv
Probably not bright of me to run that when it's supposedly formatting, but with another instance of puTTY I tried, and heres' the result:
=========
-= Cloud 9 =-
-------------------------------------------------------
> It is fine now. But we want to format it with ext4:
>
> mkfs.ext4 -L JoeyUSB3 /dev/sdb1
root@DebianPlug:~# mkfs.ext4 -L JoeyUSB3 /dev/sdb1
mke2fs 1.42.12 (29-Aug-2014)
/dev/sdb1 contains a vfat file system
Proceed anyway? (y,n) y
Creating filesystem with 7507808 4k blocks and 1880480 inodes
Filesystem UUID: 9f257101-0b9a-47b2-8682-d146b5d2cc72
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000
Allocating group tables: done
Writing inode tables: done
Creating journal (32768 blocks):
It's either taking a while or stalled. I'll wait a little bit. Worse comes to worse I could format it Ext4 w 4k blocks from Partition Wizard on ThinClient.
bodhi Wrote:
-------------------------------------------------------
> Joey,
>
> Please run lsusb again and post output here;
>
> lsusb -vvv
Probably not bright of me to run that when it's supposedly formatting, but with another instance of puTTY I tried, and heres' the result:
root@DebianPlug:~# lsusb -vvv
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 4.04
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Bus 001 Device 003: ID 0781:5575 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5575
bcdDevice 1.27
iManufacturer 1 SanDisk
iProduct 2 Cruzer Glide
iSerial 3 4C530201370809103182
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x05e3 Genesys Logic, Inc.
idProduct 0x0608 USB-2.0 4-Port HUB
bcdDevice 77.64
iManufacturer 0
iProduct 1 USB2.0 Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x00e0
Ganged power switching
Ganged overcurrent protection
TT think time 32 FS bits
Port indicators
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 100 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 40200100.ehci
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
root@DebianPlug:~#
=========
-= Cloud 9 =-
|
Re: Best Pogoplug to buy March 13, 2017 07:36PM |
Registered: 9 years ago Posts: 1,516 |
Hey bodhi, I might have rebooted it mid format, don't know. But it boots up! What should I give it? Another lsusb -vvv? Why not!
I don't see it labeled "JoeyUSB3" but let me know and I can format it Ext4 on ThinClient. What I see encourages me a lot!
-update- I see the format hadn't changed the FAT32 on the USB stick.I'm formatting it Ext4 now but is there a preference for primary or Logical partition? I'll go with Logical for now. See what happens LOL
update 2: No it doesn't boot with the newly-Ext4-formatted USB stick, but that's expected. I'll be nearby for new instructions or repeat old ones
=========
-= Cloud 9 =-
Edited 3 time(s). Last edit at 03/13/2017 08:06PM by JoeyPogoPlugE02.
root@DebianPlug:~# lsusb -vvv
Bus 003 Device 002: ID 0781:5583 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0781 SanDisk Corp.
idProduct 0x5583
bcdDevice 1.00
iManufacturer 1 SanDisk
iProduct 2 Ultra Fit
iSerial 3 4C530001180525105180
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 44
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 224mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 256 micro seconds
Device Status: 0x0000
(Bus Powered)
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Hub Descriptor:
bLength 12
bDescriptorType 42
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
bHubDecLat 0.0 micro seconds
wHubDelay 0 nano seconds
DeviceRemovable 0x00
Hub Port Status:
Port 1: 0000.0203 5Gbps power U0 enable connect
Port 2: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 15
bNumDeviceCaps 1
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x02
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x0008
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 3
Lowest fully-functional device speed is SuperSpeed (5Gbps)
bU1DevExitLat 0 micro seconds
bU2DevExitLat 0 micro seconds
Device Status: 0x0001
Self Powered
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
Bus 001 Device 003: ID 0781:5575 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5575
bcdDevice 1.27
iManufacturer 1 SanDisk
iProduct 2 Cruzer Glide
iSerial 3 4C530201370809103182
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x05e3 Genesys Logic, Inc.
idProduct 0x0608 USB-2.0 4-Port HUB
bcdDevice 77.64
iManufacturer 0
iProduct 1 USB2.0 Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x00e0
Ganged power switching
Ganged overcurrent protection
TT think time 32 FS bits
Port indicators
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 100 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 40200100.ehci
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
root@DebianPlug:~#
I don't see it labeled "JoeyUSB3" but let me know and I can format it Ext4 on ThinClient. What I see encourages me a lot!
-update- I see the format hadn't changed the FAT32 on the USB stick.I'm formatting it Ext4 now but is there a preference for primary or Logical partition? I'll go with Logical for now. See what happens LOL
update 2: No it doesn't boot with the newly-Ext4-formatted USB stick, but that's expected. I'll be nearby for new instructions or repeat old ones
=========
-= Cloud 9 =-
Edited 3 time(s). Last edit at 03/13/2017 08:06PM by JoeyPogoPlugE02.
|
Re: Best Pogoplug to buy March 13, 2017 08:50PM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
It will not booted with the Ultra Fit plugged in because your uboot envs do not allow it. This can be fixed later. For now, unplug it before booting. And then plug it in after you have logged in.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
It will not booted with the Ultra Fit plugged in because your uboot envs do not allow it. This can be fixed later. For now, unplug it before booting. And then plug it in after you have logged in.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Best Pogoplug to buy March 13, 2017 08:57PM |
Admin Registered: 13 years ago Posts: 18,585 |
Remove everything in it and create a new partition using
fdisk /dev/sdb
And then run mkfs.ext4 as above again.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
fdisk /dev/sdb
And then run mkfs.ext4 as above again.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Best Pogoplug to buy March 13, 2017 09:12PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> Remove everything in it and create a new partition
> using
>
> fdisk /dev/sdb
>
> And then run mkfs.ext4 as above again.
Okay, here's where it sits.
update: Bodhi I'd already formatted it Ext4 using Partition Magic in Windows and used the label you gave me. As you may know I'm not Einstein in Linux, but eventually what's important and what's repeated sinks in. So I beg you allow a buffer of incompetency here :-D
update 2: got to get some sleep, but hopefully all's well at your end. No worry nor hurry. I'll check back.
=========
-= Cloud 9 =-
Edited 4 time(s). Last edit at 03/14/2017 12:17AM by JoeyPogoPlugE02.
-------------------------------------------------------
> Remove everything in it and create a new partition
> using
>
> fdisk /dev/sdb
>
> And then run mkfs.ext4 as above again.
Okay, here's where it sits.
root@DebianPlug:~# fdisk /dev/sdb Welcome to fdisk (util-linux 2.25.2). Changes will remain in memory only, until you decide to write them. Be careful before using the write command. Command (m for help): mkfs.ext4 -L JoeyUSB3 /dev/sdb1 Help: DOS (MBR) a toggle a bootable flag b edit nested BSD disklabel c toggle the dos compatibility flag Generic d delete a partition l list known partition types n add a new partition p print the partition table t change a partition type v verify the partition table Misc m print this menu u change display/entry units x extra functionality (experts only) Save & Exit w write table to disk and exit q quit without saving changes Create a new label g create a new empty GPT partition table G create a new empty SGI (IRIX) partition table o create a new empty DOS partition table s create a new empty Sun partition table Command (m for help):I went on to enter w but meh, am getting sloppy.
Command (m for help): w The partition table has been altered. Calling ioctl() to re-read partition table. Syncing disks.
update: Bodhi I'd already formatted it Ext4 using Partition Magic in Windows and used the label you gave me. As you may know I'm not Einstein in Linux, but eventually what's important and what's repeated sinks in. So I beg you allow a buffer of incompetency here :-D
update 2: got to get some sleep, but hopefully all's well at your end. No worry nor hurry. I'll check back.
=========
-= Cloud 9 =-
Edited 4 time(s). Last edit at 03/14/2017 12:17AM by JoeyPogoPlugE02.
|
Re: Best Pogoplug to buy March 14, 2017 01:07AM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
> update: Bodhi I'd already formatted it Ext4 using
> Partition Magic in Windows and used the label you
> gave me.
If you did that in Windows, then there is no need to format it again whatsoever! so if in doubt do that again in Windows.
-----
We're almost ready to declare victory :) To verify it is working, do the following:
- Boot up the Pogo, and log in as root.
- Plug in the Ultra Fit.
- Get the last 20 lines of kernel log:
- Now do lsusb again to see the drive has file system and label, also to see other info:
- mount the Ultra Fit:
- Check the mount:
- change directory to its root folder, and list the content:
- Try copying some files to it:
- List the files:
If you can do all of the above without error then we can declare victory :) we'll do the performance test after you've post the results.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> update: Bodhi I'd already formatted it Ext4 using
> Partition Magic in Windows and used the label you
> gave me.
If you did that in Windows, then there is no need to format it again whatsoever! so if in doubt do that again in Windows.
-----
We're almost ready to declare victory :) To verify it is working, do the following:
- Boot up the Pogo, and log in as root.
- Plug in the Ultra Fit.
- Get the last 20 lines of kernel log:
dmesg | tail -20It should show the Ultra Fit was recognized and listed.
- Now do lsusb again to see the drive has file system and label, also to see other info:
lsusb -vvv
- mount the Ultra Fit:
mkdir -p /media/JoeyUSB3 mount /dev/sdb1 /media/JoeyUSB3
- Check the mount:
mount
- change directory to its root folder, and list the content:
cd /media/JoeyUSB3 ls -l
- Try copying some files to it:
cp -av /boot/vm* .
- List the files:
ls -lart *
If you can do all of the above without error then we can declare victory :) we'll do the performance test after you've post the results.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Best Pogoplug to buy March 14, 2017 05:26AM |
Admin Registered: 13 years ago Posts: 18,585 |
This forum format is hard to manage. I've made a mess when trying to split this thread :) So please continue posting here, until I can stitch them together!
http://forum.doozan.com/read.php?8,33041
http://forum.doozan.com/read.php?8,32702
-----
Sorry JeffS, we kind of hijacked this thread for too long. I should have moved the topic :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 03/14/2017 05:35AM by bodhi.
http://forum.doozan.com/read.php?8,33041
http://forum.doozan.com/read.php?8,32702
-----
Sorry JeffS, we kind of hijacked this thread for too long. I should have moved the topic :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 03/14/2017 05:35AM by bodhi.
|
Re: Best Pogoplug to buy March 14, 2017 01:19PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> We're almost ready to declare victory :) To verify
> it is working, do the following:
Oh yeah, plus it's Einstein's birthday and Pi Day... and things come in threes, so here goes...
>
> - Boot up the Pogo, and log in as root.
> - Plug in the Ultra Fit.
> - Get the last 20 lines of kernel log:
>
Now do lsusb again to see the drive has file system and label, also to see other info:
> - mount the Ultra Fit:
> - Check the mount:
> - change directory to its root folder, and list the content:
> - Try copying some files to it:
> - List the files:
>
-edited-
=========
-= Cloud 9 =-
Edited 3 time(s). Last edit at 03/14/2017 01:58PM by JoeyPogoPlugE02.
-------------------------------------------------------
> We're almost ready to declare victory :) To verify
> it is working, do the following:
Oh yeah, plus it's Einstein's birthday and Pi Day... and things come in threes, so here goes...
>
> - Boot up the Pogo, and log in as root.
> - Plug in the Ultra Fit.
> - Get the last 20 lines of kernel log:
dmesg | tail -20It should show the Ultra Fit was recognized and listed.
root@DebianPlug:~# dmesg | tail -20 [ 28.410304] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 63.064890] zram: Cannot change disksize for initialized device [ 63.181404] zram: Cannot change disksize for initialized device [ 63.273413] zram: Cannot change disksize for initialized device [ 63.375800] zram: Cannot change disksize for initialized device [ 226.170680] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd [ 226.195179] usb 3-1: New USB device found, idVendor=0781, idProduct=5583 [ 226.201963] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 226.209067] usb 3-1: Product: Ultra Fit [ 226.213593] usb 3-1: Manufacturer: SanDisk [ 226.217687] usb 3-1: SerialNumber: 4C530001180525105180 [ 226.227381] usb-storage 3-1:1.0: USB Mass Storage device detected [ 226.250426] scsi host2: usb-storage 3-1:1.0 [ 227.271526] scsi 2:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 227.284162] sd 2:0:0:0: [sdb] 60062500 512-byte logical blocks: (30.8 GB/28.6 GiB) [ 227.295554] sd 2:0:0:0: [sdb] Write Protect is off [ 227.302983] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 227.304954] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 227.344542] sdb: sdb1 < sdb5 > [ 227.355100] sd 2:0:0:0: [sdb] Attached SCSI removable disk root@DebianPlug:~#
>
Now do lsusb again to see the drive has file system and label, also to see other info:
lsusb -vvv>
root@DebianPlug:~# lsusb -vvv
Bus 003 Device 002: ID 0781:5583 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0781 SanDisk Corp.
idProduct 0x5583
bcdDevice 1.00
iManufacturer 1 SanDisk
iProduct 2 Ultra Fit
iSerial 3 4C530001180525105180
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 44
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 224mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 256 micro seconds
Device Status: 0x0000
(Bus Powered)
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Hub Descriptor:
bLength 12
bDescriptorType 42
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
bHubDecLat 0.0 micro seconds
wHubDelay 0 nano seconds
DeviceRemovable 0x00
Hub Port Status:
Port 1: 0000.0203 5Gbps power U0 enable connect
Port 2: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 15
bNumDeviceCaps 1
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x02
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x0008
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 3
Lowest fully-functional device speed is SuperSpeed (5Gbps)
bU1DevExitLat 0 micro seconds
bU2DevExitLat 0 micro seconds
Device Status: 0x0001
Self Powered
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
Bus 001 Device 003: ID 0781:5575 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5575
bcdDevice 1.27
iManufacturer 1 SanDisk
iProduct 2 Cruzer Glide
iSerial 3 4C530201370809103182
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x05e3 Genesys Logic, Inc.
idProduct 0x0608 USB-2.0 4-Port HUB
bcdDevice 77.64
iManufacturer 0
iProduct 1 USB2.0 Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x00e0
Ganged power switching
Ganged overcurrent protection
TT think time 32 FS bits
Port indicators
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 100 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 40200100.ehci
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
root@DebianPlug:~#
> - mount the Ultra Fit:
mkdir -p /media/JoeyUSB3 mount /dev/sdb1 /media/JoeyUSB3>
root@DebianPlug:~# mkdir -p /media/JoeyUSB3 root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3 mount: /dev/sdb1: can't read superblock root@DebianPlug:~#
> - Check the mount:
mount>
root@DebianPlug:~# mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,relatime,size=10240k,nr_inodes=14631,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=12092k,mode=755) /dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=24180k) tmpfs on /tmp type tmpfs (rw,relatime) rpc_pipefs on /run/rpc_pipefs type rpc_pipefs (rw,relatime) root@DebianPlug:~#
> - change directory to its root folder, and list the content:
> cd /media/JoeyUSB3 > ls -l >
root@DebianPlug:~# cd /media/JoeyUSB3 root@DebianPlug:/media/JoeyUSB3# ls -l total 8 drwxr-xr-x 2 root root 4096 Mar 14 14:10 . drwxr-xr-x 4 root root 4096 Mar 14 14:10 .. root@DebianPlug:/media/JoeyUSB3#
> - Try copying some files to it:
cp -av /boot/vm* .
root@DebianPlug:/media/JoeyUSB3# cp -av /boot/vm* . '/boot/vmlinuz-3.18.5-oxnas-tld-1' -> './vmlinuz-3.18.5-oxnas-tld-1' '/boot/vmlinuz-4.4.48-oxnas-tld-1' -> './vmlinuz-4.4.48-oxnas-tld-1' root@DebianPlug:/media/JoeyUSB3#
> - List the files:
>
> ls -lart * >
root@DebianPlug:/media/JoeyUSB3# ls -lart * -rwxr-xr-x 1 root root 4170000 Feb 12 2015 vmlinuz-3.18.5-oxnas-tld-1 -rw------- 1 root root 4620592 Feb 15 07:11 vmlinuz-4.4.48-oxnas-tld-1 root@DebianPlug:/media/JoeyUSB3#
-edited-
=========
-= Cloud 9 =-
Edited 3 time(s). Last edit at 03/14/2017 01:58PM by JoeyPogoPlugE02.
|
Re: Best Pogoplug to buy March 14, 2017 01:57PM |
Registered: 9 years ago Posts: 1,516 |
Bodhi yes great news, using RDP I can see yes, there's JoeyUSB3 mounted in Media, and I copied a LibreOffice file at blinding speed into it. Very cool! Mwahaaa!
Update... I'm copying an ISO image to JoeyUSB3 having sambashare'd the directory, but the ISO is copying to it at 5.46 MB/sec.
-update- read speed over LAN is 10.3 MB/sec.
My LAN is Gigabit but there's no guarantee it didn't drop to 100 MB/sec in some energy saving mode.So many variables.
* Bodhi, even if it's a worst-case scenario and this isn't fast, I'm really grateful for you trying. This would have bugged me for ages and there's no testing like testing. I haven't' given up and strongly doubt you have either, but for educational value, it was worth the pennies and time and fun, easily.
=========
-= Cloud 9 =-
Edited 3 time(s). Last edit at 03/14/2017 02:59PM by JoeyPogoPlugE02.
Update... I'm copying an ISO image to JoeyUSB3 having sambashare'd the directory, but the ISO is copying to it at 5.46 MB/sec.
-update- read speed over LAN is 10.3 MB/sec.
My LAN is Gigabit but there's no guarantee it didn't drop to 100 MB/sec in some energy saving mode.So many variables.
* Bodhi, even if it's a worst-case scenario and this isn't fast, I'm really grateful for you trying. This would have bugged me for ages and there's no testing like testing. I haven't' given up and strongly doubt you have either, but for educational value, it was worth the pennies and time and fun, easily.
=========
-= Cloud 9 =-
Edited 3 time(s). Last edit at 03/14/2017 02:59PM by JoeyPogoPlugE02.
|
Re: Best Pogoplug to buy March 14, 2017 03:39PM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
It is not quite there yet. The drive is recognized and usable. But I think your partition was bad.
Here is the summary of steps to do.
1. Do dd and hdparm test to get the raw speed without file system
2. Use fdisk to wipe out the disk and create one partition.
3. Reformat it to ext3
4. mount the drive using the label (a little bit nicer)
5. Do the files copy test using the rootfs, which is USB2.0 .
6. Do the file copy test using the new USB3.0 drive.
Anybody wants to help can chime in and help Joey fill in the details.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 03/14/2017 03:51PM by bodhi.
It is not quite there yet. The drive is recognized and usable. But I think your partition was bad.
root@DebianPlug:~# mkdir -p /media/JoeyUSB3 root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3 mount: /dev/sdb1: can't read superblock > - Check the mount: mount > root@DebianPlug:~# mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,relatime,size=10240k,nr_inodes=14631,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=12092k,mode=755) /dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=24180k) tmpfs on /tmp type tmpfs (rw,relatime) rpc_pipefs on /run/rpc_pipefs type rpc_pipefs (rw,relatime)
Here is the summary of steps to do.
1. Do dd and hdparm test to get the raw speed without file system
hdparm -Tt /dev/sb1
cd /media/JoeyUSB3 dd if=/dev/zero of=test.img bs=1G count=1 oflag=dsync
2. Use fdisk to wipe out the disk and create one partition.
fdisk /dev/sdbAnd then execute the commands to remove all partitions, and create a new one:
o n <return> (do this for the remaining questions to choose default answer)before exiting fdisk
w
3. Reformat it to ext3
mkfs.ext3 -L JoeyUSB3 /dev/sdb1
4. mount the drive using the label (a little bit nicer)
mkdir -p /media/JoeyUSB3 mount -L JoeyUSB3 -o noatime /media/JoeyUSB3
5. Do the files copy test using the rootfs, which is USB2.0 .
6. Do the file copy test using the new USB3.0 drive.
Anybody wants to help can chime in and help Joey fill in the details.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 03/14/2017 03:51PM by bodhi.
|
Re: Best Pogoplug to buy March 14, 2017 03:53PM |
Registered: 7 years ago Posts: 114 |
|
Re: Best Pogoplug to buy March 14, 2017 03:55PM |
Registered: 9 years ago Posts: 1,516 |
It's a brand new stick, but maybe it's malfunctioning:
Bodhi: crazy but I might have hit an identical folder created on the OS stick! I say this because I tried to copy the big iso to a folder next to it, and it said not enough room. Then I did properties on the folder and it's a container of the same size as the OS stick.[/b] This is cool. Deep breath. I'll be nearby. Please check attachment.
OS drive: 8GB Cruzer Glide.
USB 3 stick: 32 GB UltraFit
=========
-= Cloud 9 =-
Edited 2 time(s). Last edit at 03/14/2017 04:51PM by JoeyPogoPlugE02.
root@DebianPlug:~# hdparm -Tt /dev/sb1 -bash: hdparm: command not found root@DebianPlug:~# cd /media/JoeyUSB3 root@DebianPlug:/media/JoeyUSB3# dd if=/dev/zero of=test.img bs=1G count=1 oflag=dsync
Bodhi: crazy but I might have hit an identical folder created on the OS stick! I say this because I tried to copy the big iso to a folder next to it, and it said not enough room. Then I did properties on the folder and it's a container of the same size as the OS stick.[/b] This is cool. Deep breath. I'll be nearby. Please check attachment.
OS drive: 8GB Cruzer Glide.
USB 3 stick: 32 GB UltraFit
=========
-= Cloud 9 =-
Edited 2 time(s). Last edit at 03/14/2017 04:51PM by JoeyPogoPlugE02.
|
Re: Best Pogoplug to buy March 14, 2017 07:33PM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
> root@DebianPlug:~# hdparm -Tt /dev/sb1
> -bash: hdparm: command not found
Install hdparm:
> root@DebianPlug:~# cd /media/JoeyUSB3
> root@DebianPlug:/media/JoeyUSB3# dd if=/dev/zero o
> f=test.img bs=1G count=1 oflag=dsync
>
If there is no output from the dd command, then the partition is no good.
Please see my intruction above for how to erase and create a new partiton. And format it. Do all this in Debian :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/14/2017 11:33PM by bodhi.
> root@DebianPlug:~# hdparm -Tt /dev/sb1
> -bash: hdparm: command not found
Install hdparm:
apt-get install hdparm
> root@DebianPlug:~# cd /media/JoeyUSB3
> root@DebianPlug:/media/JoeyUSB3# dd if=/dev/zero o
> f=test.img bs=1G count=1 oflag=dsync
>
If there is no output from the dd command, then the partition is no good.
Please see my intruction above for how to erase and create a new partiton. And format it. Do all this in Debian :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/14/2017 11:33PM by bodhi.
|
Re: Best Pogoplug to buy March 14, 2017 08:48PM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
Have you tried to format the USB on Mint? I recalled there is GUI apps available for this task. Look in the accessories menu.
It was not mounted. So what you used was the empty mount point folder on OS drive, as you have figured out above!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 03/14/2017 08:52PM by bodhi.
Have you tried to format the USB on Mint? I recalled there is GUI apps available for this task. Look in the accessories menu.
It was not mounted. So what you used was the empty mount point folder on OS drive, as you have figured out above!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 03/14/2017 08:52PM by bodhi.
|
Re: Best Pogoplug to buy March 14, 2017 11:11PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> Joey,
>
> Have you tried to format the USB on Mint?
Yeah I can do that tomorrow. I have several throw-together computers that are having biannual maintenance, and I wasn't sure which to run Mint on. Got several new Mint species on hand though.
* Bodhi, minor correction possibility: did you mean apt-get above and not app-get? Anyway I installed hdparm and got the same result, so I'm apt-get updating the whole stick before proceeding. Start off with a clear head tomorrow, fingers crossed.
=========
-= Cloud 9 =-
-------------------------------------------------------
> Joey,
>
> Have you tried to format the USB on Mint?
Yeah I can do that tomorrow. I have several throw-together computers that are having biannual maintenance, and I wasn't sure which to run Mint on. Got several new Mint species on hand though.
* Bodhi, minor correction possibility: did you mean apt-get above and not app-get? Anyway I installed hdparm and got the same result, so I'm apt-get updating the whole stick before proceeding. Start off with a clear head tomorrow, fingers crossed.
=========
-= Cloud 9 =-
|
Re: Best Pogoplug to buy March 14, 2017 11:39PM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
>
> Yeah I can do that tomorrow. I have several throw-
> together computers that are having biannual mainte
> nance, and I wasn't sure which to run Mint on. Got
> several new Mint species on hand though.
Yes, make sure you format the stick using Mint. I don't trust Windows software to do Linux job :)
>
> * Bodhi, minor correction possibility: did you mea
> n apt-get above and not app-get? Anyway I installe
> d hdparm and got the same result, so I'm apt-get u
> pdating the whole stick before proceeding. Start o
> ff with a clear head tomorrow, fingers crossed.
Thanks, it was a typo.
----
Basically, you need to see it mounted in this mount command output
root@DebianPlug:~# mount
And then do this to check capacity:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
>
> Yeah I can do that tomorrow. I have several throw-
> together computers that are having biannual mainte
> nance, and I wasn't sure which to run Mint on. Got
> several new Mint species on hand though.
Yes, make sure you format the stick using Mint. I don't trust Windows software to do Linux job :)
>
> * Bodhi, minor correction possibility: did you mea
> n apt-get above and not app-get? Anyway I installe
> d hdparm and got the same result, so I'm apt-get u
> pdating the whole stick before proceeding. Start o
> ff with a clear head tomorrow, fingers crossed.
Thanks, it was a typo.
----
Basically, you need to see it mounted in this mount command output
root@DebianPlug:~# mount
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,relatime,size=10240k,nr_inodes=14631,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=12092k,mode=755) /dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=24180k) tmpfs on /tmp type tmpfs (rw,relatime) rpc_pipefs on /run/rpc_pipefs type rpc_pipefs (rw,relatime)The only drive that was mounted here is sda1 which is the the rootfs on your Cruzer Glide.
And then do this to check capacity:
df -hIt should show the sizes and usage of both sda1 and sdb1.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 09:04PM |
Registered: 9 years ago Posts: 1,516 |
The UltraFit 32GB was re-formatted using Mint Cinnamon's G-Parted, and no idea if it worked, but I went to page 3 and thought this looked good:
Here goes
I hope this doesn't infuriate you - I'm just going slow, playing it safe...
-update- cool! I'm seeing some familiarity here :-)
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/15/2017 09:07PM by JoeyPogoPlugE02.
fdisk -l dmesg lsusb
Here goes
root@DebianPlug:~# fdisk -l
Disk /dev/mtdblock0: 14 MiB, 14680064 bytes, 28672 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xaaaaaaaa
Device Boot Start End Sectors Size Id Type
/dev/mtdblock0p1 ? 2863311530 5726623059 2863311530 1.3T aa unknown
/dev/mtdblock0p2 ? 2863311530 5726623059 2863311530 1.3T aa unknown
/dev/mtdblock0p3 ? 2863311530 4294989139 1431677610 682.7G aa unknown
/dev/mtdblock0p4 ? 2863311530 5721052499 2857740970 1.3T aa unknown
Disk /dev/mtdblock1: 114 MiB, 119537664 bytes, 233472 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk /dev/sda: 7.3 GiB, 7849115648 bytes, 15330304 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x01ecce21
Device Boot Start End Sectors Size Id Type
/dev/sda1 2048 15147007 15144960 7.2G 83 Linux
Disk /dev/zram0: 22.1 MiB, 23220224 bytes, 5669 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/zram1: 22.1 MiB, 23220224 bytes, 5669 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/zram2: 22.1 MiB, 23220224 bytes, 5669 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/zram3: 22.1 MiB, 23220224 bytes, 5669 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/sdb: 28.7 GiB, 30752000000 bytes, 60062500 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xa7400f17
Device Boot Start End Sectors Size Id Type
/dev/sdb1 1985 60049407 60047423 28.6G f W95 Ext'd (LBA)
/dev/sdb5 2048 60049407 60047360 28.6G 83 Linux
root@DebianPlug:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.48-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP PREEMPT Wed Feb 15 02:59:11 PST 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Pogoplug V3 Pro
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat c08a6980, node_mem_map c7ef9000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @c7eda000 s17696 r8192 d23264 u49152
[ 0.000000] pcpu-alloc: s17696 r8192 d23264 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 117048K/131072K available (6406K kernel code, 288K rwdata, 1908K rodata, 228K init, 247K bss, 14024K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0826ddc (8316 kB)
.init : 0xc0827000 - 0xc0860000 ( 228 kB)
.data : 0xc0860000 - 0xc08a8338 ( 289 kB)
.bss : 0xc08a8338 - 0xc08e6310 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.000161] Console: colour dummy device 80x30
[ 0.000192] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.050017] pid_max: default: 32768 minimum: 301
[ 0.050183] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.050201] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.051008] Initializing cgroup subsys net_cls
[ 0.051087] CPU: Testing write buffer coherency: ok
[ 0.051520] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.190131] Brought up 2 CPUs
[ 0.190156] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.190935] devtmpfs: initialized
[ 0.195740] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.195998] prandom: seed boundary self test passed
[ 0.200412] prandom: 100 self tests passed
[ 0.200440] pinctrl core: initialized pinctrl subsystem
[ 0.201249] NET: Registered protocol family 16
[ 0.201789] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.230018] cpuidle: using governor ladder
[ 0.260008] cpuidle: using governor menu
[ 0.265000] gpio-oxnas 44000000.gpio: at address c8848000
[ 0.265384] gpio-oxnas 44100000.gpio: at address c884a000
[ 0.265958] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.388464] oxnas-pcie 47c00000.pcie-controller: PCIe version/deviceID 0x82510b5
[ 0.388584] oxnas-pcie 47c00000.pcie-controller: link up
[ 0.388899] oxnas-pcie 47c00000.pcie-controller: PCI host bridge to bus 0000:00
[ 0.388925] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[ 0.388945] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[ 0.388961] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
[ 0.388979] pci_bus 0000:00: root bus resource [bus 00-7f]
[ 0.389043] pci 0000:00:00.0: [1912:0015] type 00 class 0x0c0330
[ 0.389132] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[ 0.389314] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 0.389670] PCI: bus0: Fast back to back transfers disabled
[ 0.389765] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x48001fff 64bit]
[ 0.390315] vgaarb: loaded
[ 0.390814] SCSI subsystem initialized
[ 0.391178] libata version 3.00 loaded.
[ 0.391690] usbcore: registered new interface driver usbfs
[ 0.391800] usbcore: registered new interface driver hub
[ 0.391961] usbcore: registered new device driver usb
[ 0.392174] pps_core: LinuxPPS API ver. 1 registered
[ 0.392189] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.392235] PTP clock support registered
[ 0.394334] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.412848] NET: Registered protocol family 2
[ 0.413731] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.413772] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.413808] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.413905] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.413949] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.414213] NET: Registered protocol family 1
[ 0.414758] RPC: Registered named UNIX socket transport module.
[ 0.414778] RPC: Registered udp transport module.
[ 0.414791] RPC: Registered tcp transport module.
[ 0.414804] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.414865] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 0.414940] PCI: CLS 32 bytes, default 32
[ 0.415270] Unpacking initramfs...
[ 0.805859] Freeing initrd memory: 3644K (c7a99000 - c7e28000)
[ 0.807252] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.807421] Initialise system trusted keyring
[ 0.832847] zbud: loaded
[ 0.851376] NFS: Registering the id_resolver key type
[ 0.851448] Key type id_resolver registered
[ 0.851461] Key type id_legacy registered
[ 0.851504] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.851527] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.852428] fuse init (API version 7.23)
[ 0.854433] Key type big_key registered
[ 0.933701] Key type asymmetric registered
[ 0.933729] Asymmetric key parser 'x509' registered
[ 0.933859] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.933888] io scheduler noop registered
[ 0.933908] io scheduler deadline registered
[ 0.933969] io scheduler cfq registered (default)
[ 0.934620] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.936199] console [ttyS0] disabled
[ 0.936291] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.521661] console [ttyS0] enabled
[ 1.587688] loop: module loaded
[ 1.839705] scsi host0: sata_oxnas
[ 1.892968] ata1: SATA max UDMA/133 irq 7
[ 1.897057] sata_oxnas: resetting SATA core
[ 1.898088] nand: Could not find valid ONFI parameter page; aborting
[ 1.898132] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 1.898137] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 1.898145] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.898160] Scanning device for bad blocks
[ 1.980259] 2 ofpart partitions found on MTD device 41000000.nand
[ 1.986327] Creating 2 MTD partitions on "41000000.nand":
[ 1.991738] 0x000000000000-0x000000e00000 : "boot"
[ 1.998407] 0x000000e00000-0x000008000000 : "data"
[ 2.005670] oxnas-gmac 40400000.ethernet: no reset control found
[ 2.011783] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 2.016811] Ring mode enabled
[ 2.019842] DMA HW capability register supported
[ 2.024386] Enhanced/Alternate descriptors
[ 2.028715] Enabled extended descriptors
[ 2.032719] RX Checksum Offload Engine supported (type 2)
[ 2.038174] TX Checksum insertion supported
[ 2.042434] Wake-Up On Lan supported
[ 2.046072] Enable RX Mitigation via HW Watchdog Timer
[ 2.067578] libphy: stmmac: probed
[ 2.071029] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 2.077440] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 2.084116] PPP generic driver version 2.4.2
[ 2.088931] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.095495] ehci-pci: EHCI PCI platform driver
[ 2.100421] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 2.105920] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 2.113776] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 2.130147] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 2.136458] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.143249] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.150458] usb usb1: Product: EHCI Host Controller
[ 2.155312] usb usb1: Manufacturer: Linux 4.4.48-oxnas-tld-1 ehci_hcd
[ 2.161733] usb usb1: SerialNumber: 40200100.ehci
[ 2.167347] hub 1-0:1.0: USB hub found
[ 2.171210] hub 1-0:1.0: 2 ports detected
[ 2.176217] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 2.181519] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 2
[ 2.194424] xhci_hcd 0000:00:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x00000090
[ 2.203294] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.210058] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.217287] usb usb2: Product: xHCI Host Controller
[ 2.222167] usb usb2: Manufacturer: Linux 4.4.48-oxnas-tld-1 xhci-hcd
[ 2.228577] usb usb2: SerialNumber: 0000:00:00.0
[ 2.234158] hub 2-0:1.0: USB hub found
[ 2.237972] hub 2-0:1.0: 2 ports detected
[ 2.242890] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 2.248112] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 3
[ 2.255703] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.264076] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.271060] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.278251] usb usb3: Product: xHCI Host Controller
[ 2.283148] usb usb3: Manufacturer: Linux 4.4.48-oxnas-tld-1 xhci-hcd
[ 2.289561] usb usb3: SerialNumber: 0000:00:00.0
[ 2.289999] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.300638] hub 3-0:1.0: USB hub found
[ 2.304450] hub 3-0:1.0: 2 ports detected
[ 2.309547] usbcore: registered new interface driver cdc_acm
[ 2.315225] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.323340] usbcore: registered new interface driver cdc_wdm
[ 2.329187] usbcore: registered new interface driver usb-storage
[ 2.335383] usbcore: registered new interface driver usbserial
[ 2.341591] usbcore: registered new interface driver usbserial_generic
[ 2.348149] usbserial: USB Serial support registered for generic
[ 2.354580] mousedev: PS/2 mouse device common for all mice
[ 2.360381] i2c /dev entries driver
[ 2.365176] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.371059] usbcore: registered new interface driver usbhid
[ 2.376606] usbhid: USB HID core driver
[ 2.382699] NET: Registered protocol family 10
[ 2.388638] sit: IPv6 over IPv4 tunneling driver
[ 2.394286] NET: Registered protocol family 17
[ 2.398868] Key type dns_resolver registered
[ 2.404656] registered taskstats version 1
[ 2.408770] Loading compiled-in X.509 certificates
[ 2.413706] zswap: loaded using pool lzo/zbud
[ 2.433889] Key type encrypted registered
[ 2.452945] Freeing unused kernel memory: 228K (c0827000 - c0860000)
[ 2.490186] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[ 2.596490] udevd[99]: starting version 175
[ 2.652510] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.659200] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.685708] usb 1-1: Product: USB2.0 Hub
[ 2.711308] hub 1-1:1.0: USB hub found
[ 2.720238] hub 1-1:1.0: 4 ports detected
[ 3.020254] usb 1-1.1: new high-speed USB device number 3 using oxnas-ehci
[ 3.141301] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5575
[ 3.148152] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.155514] usb 1-1.1: Product: Cruzer Glide
[ 3.159764] usb 1-1.1: Manufacturer: SanDisk
[ 3.164052] usb 1-1.1: SerialNumber: 4C530201370809103182
[ 3.170831] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 3.177594] scsi host1: usb-storage 1-1.1:1.0
[ 3.205639] usbcore: registered new interface driver uas
[ 4.181427] scsi 1:0:0:0: Direct-Access SanDisk Cruzer Glide 1.27 PQ: 0 ANSI: 6
[ 4.196131] sd 1:0:0:0: [sda] 15330304 512-byte logical blocks: (7.85 GB/7.31 GiB)
[ 4.206302] sd 1:0:0:0: [sda] Write Protect is off
[ 4.211338] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 4.212423] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.232084] sda: sda1
[ 4.243292] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 13.514549] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 13.544046] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 15.038837] udevd[297]: starting version 175
[ 17.214064] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 17.257996] random: nonblocking pool is initialized
[ 17.591677] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 20.784898] Adding 1048572k swap on /swapfile1. Priority:-1 extents:360 across:1169636k FS
[ 23.611594] zram: Added device: zram0
[ 23.634224] zram: Added device: zram1
[ 23.642526] zram: Added device: zram2
[ 23.671933] zram: Added device: zram3
[ 23.702763] zram0: detected capacity change from 0 to 23220224
[ 23.774753] Adding 22672k swap on /dev/zram0. Priority:10 extents:1 across:22672k SSFS
[ 23.788352] zram1: detected capacity change from 0 to 23220224
[ 23.846574] Adding 22672k swap on /dev/zram1. Priority:10 extents:1 across:22672k SSFS
[ 23.859934] zram2: detected capacity change from 0 to 23220224
[ 23.924277] Adding 22672k swap on /dev/zram2. Priority:10 extents:1 across:22672k SSFS
[ 23.935201] zram3: detected capacity change from 0 to 23220224
[ 24.013096] Adding 22672k swap on /dev/zram3. Priority:10 extents:1 across:22672k SSFS
[ 29.320294] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 53.659010] zram: Cannot change disksize for initialized device
[ 53.701419] zram: Cannot change disksize for initialized device
[ 53.753600] zram: Cannot change disksize for initialized device
[ 53.817088] zram: Cannot change disksize for initialized device
[ 408.490754] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 408.515240] usb 3-1: New USB device found, idVendor=0781, idProduct=5583
[ 408.530383] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 408.537500] usb 3-1: Product: Ultra Fit
[ 408.550123] usb 3-1: Manufacturer: SanDisk
[ 408.554211] usb 3-1: SerialNumber: 4C530001180525105180
[ 408.562780] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 408.574553] scsi host2: usb-storage 3-1:1.0
[ 409.572177] scsi 2:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6
[ 409.596318] sd 2:0:0:0: [sdb] 60062500 512-byte logical blocks: (30.8 GB/28.6 GiB)
[ 409.606420] sd 2:0:0:0: [sdb] Write Protect is off
[ 409.614568] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 409.616343] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 409.652034] sdb: sdb1 < sdb5 >
[ 409.670681] sd 2:0:0:0: [sdb] Attached SCSI removable disk
root@DebianPlug:~# lsusb
Bus 003 Device 002: ID 0781:5583 SanDisk Corp.
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0781:5575 SanDisk Corp.
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@DebianPlug:~#
I hope this doesn't infuriate you - I'm just going slow, playing it safe...
-update- cool! I'm seeing some familiarity here :-)
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/15/2017 09:07PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 09:14PM |
Registered: 9 years ago Posts: 1,516 |
lsusb -vvv
Saw this there recently, don't know if it helps:
root@DebianPlug:~# lsusb -vvv
Bus 003 Device 002: ID 0781:5583 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0781 SanDisk Corp.
idProduct 0x5583
bcdDevice 1.00
iManufacturer 1 SanDisk
iProduct 2 Ultra Fit
iSerial 3 4C530001180525105180
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 44
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 224mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 256 micro seconds
Device Status: 0x0000
(Bus Powered)
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Hub Descriptor:
bLength 12
bDescriptorType 42
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
bHubDecLat 0.0 micro seconds
wHubDelay 0 nano seconds
DeviceRemovable 0x00
Hub Port Status:
Port 1: 0000.0203 5Gbps power U0 enable connect
Port 2: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 15
bNumDeviceCaps 1
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x02
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x0008
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 3
Lowest fully-functional device speed is SuperSpeed (5Gbps)
bU1DevExitLat 0 micro seconds
bU2DevExitLat 0 micro seconds
Device Status: 0x0001
Self Powered
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
Bus 001 Device 003: ID 0781:5575 SanDisk Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5575
bcdDevice 1.27
iManufacturer 1 SanDisk
iProduct 2 Cruzer Glide
iSerial 3 4C530201370809103182
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x05e3 Genesys Logic, Inc.
idProduct 0x0608 USB-2.0 4-Port HUB
bcdDevice 77.64
iManufacturer 0
iProduct 1 USB2.0 Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x00e0
Ganged power switching
Ganged overcurrent protection
TT think time 32 FS bits
Port indicators
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 100 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.48-oxnas-tld-1 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 40200100.ehci
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered
root@DebianPlug:~#
=========
-= Cloud 9 =-
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 10:27PM |
Registered: 9 years ago Posts: 1,516 |
As you can see I proceeded, and after seeing the error for sdb1 I got the crazy idea to try sdb5 because it was also listed:
Attached is the result looking into Pogo using RDP. I can't copy to and fro yet, but will mess with permissions.
I'm taking nightly heart meds/melatonin and will go into coma in 90 minutes :-)
=========
-= Cloud 9 =-
root@DebianPlug:~# mkdir -p /media/JoeyUSB3 root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3 mount: /dev/sdb1: can't read superblock root@DebianPlug:~# mount /dev/sdb5 /media/JoeyUSB3 root@DebianPlug:~#
Attached is the result looking into Pogo using RDP. I can't copy to and fro yet, but will mess with permissions.
I'm taking nightly heart meds/melatonin and will go into coma in 90 minutes :-)
=========
-= Cloud 9 =-
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 11:10PM |
Registered: 9 years ago Posts: 1,516 |
mount
root@DebianPlug:~# mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,relatime,size=10240k,nr_inodes=14631,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=12092k,mode=755) /dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=24180k) tmpfs on /tmp type tmpfs (rw,relatime) rpc_pipefs on /run/rpc_pipefs type rpc_pipefs (rw,relatime) /dev/sdb5 on /media/JoeyUSB3 type ext4 (ro,relatime,data=ordered)
I never could get read nor write permissions for that folder/directory. I'll be up another hour and check in.
Really sorry I'm not all there with this, but am encouraged compared to the 1st day here :-)
=========
-= Cloud 9 =-
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 11:32PM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
> root@DebianPlug:~# lsusb -vvv
>
> Bus 003 Device 002: ID 0781:5583 SanDisk Corp.
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 3.00
> bDeviceClass 0 (Defined at Interface
> level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 9
> idVendor 0x0781 SanDisk Corp.
> idProduct 0x5583
> bcdDevice 1.00
> iManufacturer 1 SanDisk
> iProduct 2 Ultra Fit
> iSerial 3 4C530001180525105180
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 44
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0x80
> (Bus Powered)
> MaxPower 224mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 2
> bInterfaceClass 8 Mass Storage
> bInterfaceSubClass 6 SCSI
> bInterfaceProtocol 80 Bulk-Only
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x02 EP 2 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 15
> Binary Object Store Descriptor:
> bLength 5
> bDescriptorType 15
> wTotalLength 22
> bNumDeviceCaps 2
> USB 2.0 Extension Device Capability:
> bLength 7
> bDescriptorType 16
> bDevCapabilityType 2
> bmAttributes 0x00000002
> Link Power Management (LPM) Supported
> SuperSpeed USB Device Capability:
> bLength 10
> bDescriptorType 16
> bDevCapabilityType 3
> bmAttributes 0x00
> wSpeedsSupported 0x000e
> Device can operate at Full Speed (12Mbps)
> Device can operate at High Speed (480Mbps)
> Device can operate at SuperSpeed (5Gbps)
> bFunctionalitySupport 1
> Lowest fully-functional device speed is Full
> Speed (12Mbps)
> bU1DevExitLat 10 micro seconds
> bU2DevExitLat 256 micro seconds
> Device Status: 0x0000
> (Bus Powered)
This is great!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> root@DebianPlug:~# lsusb -vvv
>
> Bus 003 Device 002: ID 0781:5583 SanDisk Corp.
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 3.00
> bDeviceClass 0 (Defined at Interface
> level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 9
> idVendor 0x0781 SanDisk Corp.
> idProduct 0x5583
> bcdDevice 1.00
> iManufacturer 1 SanDisk
> iProduct 2 Ultra Fit
> iSerial 3 4C530001180525105180
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 44
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0x80
> (Bus Powered)
> MaxPower 224mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 2
> bInterfaceClass 8 Mass Storage
> bInterfaceSubClass 6 SCSI
> bInterfaceProtocol 80 Bulk-Only
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x02 EP 2 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0400 1x 1024 bytes
> bInterval 0
> bMaxBurst 15
> Binary Object Store Descriptor:
> bLength 5
> bDescriptorType 15
> wTotalLength 22
> bNumDeviceCaps 2
> USB 2.0 Extension Device Capability:
> bLength 7
> bDescriptorType 16
> bDevCapabilityType 2
> bmAttributes 0x00000002
> Link Power Management (LPM) Supported
> SuperSpeed USB Device Capability:
> bLength 10
> bDescriptorType 16
> bDevCapabilityType 3
> bmAttributes 0x00
> wSpeedsSupported 0x000e
> Device can operate at Full Speed (12Mbps)
> Device can operate at High Speed (480Mbps)
> Device can operate at SuperSpeed (5Gbps)
> bFunctionalitySupport 1
> Lowest fully-functional device speed is Full
> Speed (12Mbps)
> bU1DevExitLat 10 micro seconds
> bU2DevExitLat 256 micro seconds
> Device Status: 0x0000
> (Bus Powered)
This is great!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 11:34PM |
Admin Registered: 13 years ago Posts: 18,585 |
> root@DebianPlug:~# mkdir -p /media/JoeyUSB3
> root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3
> mount: /dev/sdb1: can't read superblock
This is bad! should not see the error .
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUSB3
> mount: /dev/sdb1: can't read superblock
This is bad! should not see the error .
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 11:37PM |
Admin Registered: 13 years ago Posts: 18,585 |
> root@DebianPlug:~# mount
> /dev/sdb5 on /media/JoeyUSB3 type ext4 (ro,relatim
> e,data=ordered)
It is good that it was mounted.
>
> I never could get read nor write permissions for t
> hat folder/directory.
That means there is something wrong with the partition. And it must have been related to the previous error about "super block".
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/15/2017 11:39PM by bodhi.
> /dev/sdb5 on /media/JoeyUSB3 type ext4 (ro,relatim
> e,data=ordered)
It is good that it was mounted.
>
> I never could get read nor write permissions for t
> hat folder/directory.
That means there is something wrong with the partition. And it must have been related to the previous error about "super block".
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/15/2017 11:39PM by bodhi.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 11:42PM |
Registered: 9 years ago Posts: 1,516 |
bodhi Wrote:
-------------------------------------------------------
> > root@DebianPlug:~# mkdir -p /media/JoeyUSB3
> > root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUS
> B3
> > mount: /dev/sdb1: can't read superblock
>
> This is bad! should not see the error .
I'm going to try to get another USB 3 stick in the next three days (before my $5-off prize at BestBuy expires), maybe mine is having issues. Advice well taken if it's in stock, but I'm trusting UltraFits less and less and think they get too hot. I wondered before if Pogos used metal in the connectors as part of their heat sink scheme but this time it's at the end of a breakout box (allow 30 days shipping to Midwest US), which I dare say is much higher quality than the picture lets on.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/15/2017 11:49PM by JoeyPogoPlugE02.
-------------------------------------------------------
> > root@DebianPlug:~# mkdir -p /media/JoeyUSB3
> > root@DebianPlug:~# mount /dev/sdb1 /media/JoeyUS
> B3
> > mount: /dev/sdb1: can't read superblock
>
> This is bad! should not see the error .
I'm going to try to get another USB 3 stick in the next three days (before my $5-off prize at BestBuy expires), maybe mine is having issues. Advice well taken if it's in stock, but I'm trusting UltraFits less and less and think they get too hot. I wondered before if Pogos used metal in the connectors as part of their heat sink scheme but this time it's at the end of a breakout box (allow 30 days shipping to Midwest US), which I dare say is much higher quality than the picture lets on.
=========
-= Cloud 9 =-
Edited 1 time(s). Last edit at 03/15/2017 11:49PM by JoeyPogoPlugE02.
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 11:46PM |
Admin Registered: 13 years ago Posts: 18,585 |
I am not sure why Mint created 2 partitions when you format it! unless you told it to do that.
Now it does not hurt to go back to Mint and find out how to erase all partitions and create one new partition, format it to Ext3 or Ext4 at the same time (Ext3 or Ext4 does not matter).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Device Boot Start End Sectors Size Id Type /dev/sdb1 1985 60049407 60047423 28.6G f W95 Ext'd (LBA) /dev/sdb5 2048 60049407 60047360 28.6G 83 Linux
Now it does not hurt to go back to Mint and find out how to erase all partitions and create one new partition, format it to Ext3 or Ext4 at the same time (Ext3 or Ext4 does not matter).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Pogoplug V3 OXNAS - USB 3.0 on mPCIe - Main thread March 15, 2017 11:50PM |
Admin Registered: 13 years ago Posts: 18,585 |
Joey,
> I'm going to try to get another USB 3 stick in the
> next three days (before my $5-off prize at BestBuy
> expires), maybe mine is having issues.
That might be good to do. Remember the Ultra Fit 32GB is troublesome for booting. But it should work after Linux is running... so I think your formatting was incorrect. I'm going to play with the Mint GUI to format my spare USB 3.0 stick to see if I can spot your mistake (if any).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I'm going to try to get another USB 3 stick in the
> next three days (before my $5-off prize at BestBuy
> expires), maybe mine is having issues.
That might be good to do. Remember the Ultra Fit 32GB is troublesome for booting. But it should work after Linux is running... so I think your formatting was incorrect. I'm going to play with the Mint GUI to format my spare USB 3.0 stick to see if I can spot your mistake (if any).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
