dpf-ax: unsupported dpf - requests

@superelchi

Find out the problem
The firmware pt824 works well. It's the problem of the config blacklight.

cuckoohello Wrote:
-------------------------------------------------------
> dpfsend works well.
> but the others with the same lcd4linux config
> works well with DPF of olderzeus's version.
> And I have tested it with vnc, it works well too.
> If I using other firmware such as linkdelight_4,
> the screen is divided into several areas. some of
> them shows correctly( and tested it under
> lcd4linux) .



Edited 1 time(s). Last edit at 01/05/2013 09:00AM by cuckoohello.

@superelchi

Find out the problem.
The firmware pt824 works well. It's the problem of the config blacklight.
Thanks!



Edited 1 time(s). Last edit at 01/05/2013 09:01AM by cuckoohello.

cuckoohello Wrote:
-------------------------------------------------------
> @superelchi
>
> Find out the problem.
> The firmware pt824 works well. It's the problem of
> the config blacklight.
> Thanks!

Okay. So it's not compatible with pt824.
Please try attached fw.

superelchi

superelchi Wrote:
-------------------------------------------------------
> cuckoohello Wrote:
> --------------------------------------------------
> -----
> > @superelchi
> >
> > Find out the problem.
> > The firmware pt824 works well. It's the problem
> of
> > the config blacklight.
> > Thanks!
>
> Okay. So it's not compatible with pt824.
> Please try attached fw.
>
> superelchi
Thanks!
It works very well with the origin config.
But while I set the backlight to a high value or just not config, the firmware pt824 works.

FYI: new model "taobao" in svn.

cuckoohello Wrote:
-------------------------------------------------------
> But while I set the backlight to a high value or
> just not config, the firmware pt824 works.

Thats just luck. Your display has a different brightness control. If you would try to adjust the brightness in the dpfs menu with the pt824 fw, same thing will happen.
So better use a correct fw. :-)

superelchi

Hi

I got this one form ebay, you also have him linked but gives this message

Detecting & reading dpf flash...
Opening generic SCSI device '/dev/sg2'
Manufacturer: Macronix
Size : 1 MB
Reading 100000 bytes...
Flash written to file 'identify.out/full.bin'.

Looking for firmware.............: Found (buildwin, 128x128 px).
Looking for Openwin..............: Found.
Looking for LcdIniTbl............: Found.
Looking for known signatures.....: None.
Looking for known version info...: None.

Sorry, no matching dpf found.
But following models have a partial signature match: [['acme_1'], ['jovisa']]

url of buying the screen
http://www.ebay.com/itm/280828187564?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649

I attached placed the dump right here

@kroonen

Please try attached fw.

superelchi

Superelchi Hello: I'm buying another LCD as brick and remove the fw, I tried again with all funcionanse hackfw and the screen stays black, must be a new device I buy here http://www.ebay .com/itm/230670117410? ssPageName = STRK: MEWNX: IT & _trksid = p3984.m1439.l2649 leave the FW here in case it might look ...http://www.file-upload.net/download-7073300/full01.bin.html

Thank you very much for your effort
best regards

Hi

This works thnx.

For compiling against lcd4linux, what must I do ?

I tried this

root@gandalf:/home/richard/Downloads/dpf-ax# ./build-dpf-lcd4linux.sh
lcd4linux installed, not fetching
Existing drv_dpf.c found, not patching
./bootstrap:> aclocal
aclocal: `configure.ac' or `configure.in' is required
configure: error: cannot find sources (lcd4linux.c) in . or ..
make: *** No targets specified and no makefile found. Stop.
root@gandalf:/home/richard/Downloads/dpf-ax#



Edited 1 time(s). Last edit at 01/17/2013 03:55PM by kroonen.

@Papa Oscar
Please try attached fw.

@kroonen
Looks like your dpf-ax installation is broken or some dependencies are missing.
RomanG wrote a small howto. Maybe this helps.

superelchi

superelchi Wrote:
-------------------------------------------------------
> @Papa Oscar
> Please try attached fw.
>
> @kroonen
> Looks like your dpf-ax installation is broken or
> some dependencies are missing.
> RomanG wrote a small
> [url=http://forum.doozan.com/read.php?9,2435,9321#
> msg-9321]howto[/url]. Maybe this helps.
>
> superelchi

Thanks superelchi I put fw  fw_disp_delightdigi_black_portrait.bin but only white screen,, also tried fw_disp_delightdigi_2_portrait.bin and black screen.
If I put full.bin Penguins welcome back
best greetings

Papa Oscar Wrote:
-------------------------------------------------------
>
> Thanks superelchi I put fw 
> fw_disp_delightdigi_black_portrait.bin but only
> white screen,, also tried
> fw_disp_delightdigi_2_portrait.bin and black
> screen.
> If I put full.bin Penguins welcome back
> best greetings

Yes, there is something strange going on in your dpfs lcdblit routine...
Please try this fw. Better?

superelchi

Hello superelchi: thanks again for your time.
I have set the FW fw_disp_linkdelight_black_portrait.zip
and the screen goes white when you press M and nothing comes out.
best regards

Hello Papa Oscar,

do you mean you can see the eyes after powre on / reset and get a white screen on pressing menu?
Or is the screen always white?

superelchi

superelchi Wrote:
-------------------------------------------------------
> Hello Papa Oscar,
>
> do you mean you can see the eyes after powre on /
> reset and get a white screen on pressing menu?
> Or is the screen always white?
>
> superelchi

I never see eyes ... when I press "Reset" button. lcd in black.,
When I press button "M" in white lcd. no menu, no photo of the eyes.
Sorry my bad English.
Greetings

@ Papa Oscar
Okay - so this one needs some heavier treatment. I will have a closer look as soon as time permits. Please keep monitoring this thread. I will come back to you!

superelchi

Thanks ... I expect no problems.
regards

FYI: new revision in svn.

* New model: abeyerr_black_2.
* New Work-In-Progress model: linkdelight_black_portrait - NOT WORKING ATM!

superelchi

Hello there,

I bought a DPF from this seller on Amazon which seems not supported :

sudo ./fulldump.py /dev/sr0
Opening generic SCSI device '/dev/sr0'
Manufacturer: Apple
Size        : 1 MB
Reading 100000 bytes...
Wrote full.bin

python identify.py full.bin 
Looking for firmware.............: Found (coby, 128x128 px).
Looking for Openwin..............: Found.
Looking for LcdIniTbl............: None.
Looking for known signatures.....: None.
Looking for known version info...: None.

Sorry, no matching dpf found.
But following models have a partial signature match: [['abeyerr_black_2'], ['acme_1'], ['jovisa']]

No reference on this DPF, just the "Digital Photo Frame" on the screen face.

Edit: after further investigations using the supported types page, this DPF may be a variation of dx27893 firmware.

I've seen other sellers proposing this DPF (using the same picture) : http://preview.tinyurl.com/a5y9wc6

The full.bin is attached.
Thanks in advance if you can help!



Edited 1 time(s). Last edit at 01/27/2013 06:45AM by glb.

@glb:

please try attached fw.

superelchi

Whow,
it works perfectly, thank you very much.

You should propose to people to give you small donation through Paypal for your help.
I'll be glad to participate.

Thanks again,
-Éric.

FYI: new model sunluxy in svn.

superelchi

Hi,

I got a new display device from delight. It idenfify itself as an taobao.

I get an error about the flash size. Is this a problem, or should I do an -f (force?)


root@gandalf:~/dpf-ax/trunk/fw# python fulldump.py /dev/sr1
Opening generic SCSI device '/dev/sr1'
Manufacturer: Apple
Size : 2 MB
Reading 200000 bytes...
Wrote full.bin

root@gandalf:~/dpf-ax/trunk/fw# python identify.py full.bin Looking for firmware.............: Found (buildwin, 320x240 px).
Looking for Openwin..............: Found.
Looking for LcdIniTbl............: Found.
Looking for known signatures.....: Found.

Your dpf is compatible with model ['taobao'].

root@gandalf:~/dpf-ax/trunk/fw# python restore.py /root/fw/fw_disp_taobao.bin Found AX206 DPF (bootloader)
Manufacturer: Apple
Size : 2 MB
Flash size mismatch, specify -f to force
root@gandalf:~/dpf-ax/trunk/fw#



Edited 1 time(s). Last edit at 02/15/2013 01:54PM by kroonen.

kroonen Wrote:
-------------------------------------------------------
> Hi,
>
> I got a new display device from delight. It
> idenfify itself as an taobao.
>
> I get an error about the flash size. Is this a
> problem, or should I do an -f (force?)
>

Because our firmware is smaller than your flash-chip you always have to use the "-f" parameter.

superelchi

Hi superelchi

I have been trying to flash this device for couple days now with no sucess.it would be great if you can take look and let me know what firmware to use and or patch current firmware.

Thanks
Attached file is current dump of firmware.it is zipped so it can be uploaded


Attached is dmesg,lsusb,and hexedit part of firmware:


[ 1107.188564] hid-generic 0003:1908:3318.0003: hiddev0,hidraw2: USB HID v2.01 Device [BUILDWIN BL206v1.0.0] on usb-0000:02:00.0-2.1/input0
[ 1107.273307] usb 2-2.1: USB disconnect, device number 6
[ 1117.074150] parport0: lp tried to release parport when not owner
[ 1117.074166] parport0: ppdev0 forgot to release port
[ 1319.910553] usb 2-2.1: new full-speed USB device number 7 using uhci_hcd
[ 1320.247795] usb 2-2.1: New USB device found, idVendor=1908, idProduct=0102
[ 1320.247799] usb 2-2.1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 1320.247802] usb 2-2.1: Product: Digital Photo Frame
[ 1320.247803] usb 2-2.1: Manufacturer: BUILDWIN
[ 1320.247805] usb 2-2.1: SerialNumber: 200807101900000000
[ 1320.298576] Initializing USB Mass Storage driver...
[ 1320.304004] scsi3 : usb-storage 2-2.1:1.0
[ 1320.304278] usbcore: registered new interface driver usb-storage
[ 1320.304279] USB Mass Storage support registered.
[ 1320.305646] usbcore: registered new interface driver uas
[ 1321.326142] scsi 3:0:0:0: CD-ROM buildwin Photo Frame 1.01 PQ: 0 ANSI: 2
[ 1321.359422] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 1321.360737] sr 3:0:0:0: Attached scsi CD-ROM sr1
[ 1321.362231] sr 3:0:0:0: Attached scsi generic sg2 type 5
[ 1321.800805] usb 2-2.1: reset full-speed USB device number 7 using uhci_hcd
[ 1322.375634] usb 2-2.1: reset full-speed USB device number 7 using uhci_hcd



____________________________________________________________________________________________________________________________



Bus 002 Device 007: ID 1908:0102 GEMBIRD
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1908 GEMBIRD
idProduct 0x0102
bcdDevice 2.00
iManufacturer 2
iProduct 3
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 4
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0



______________________________________________________________________________________________________________________________

00000180 50 72 6F 63 54 62 6C 32 0B 30 0C 46 E2 06 00 00 0B 2A 0D 27 A2 08 00 00 ProcTbl2.0.F.....*.'....
00000198 0B 2A 0B FF A2 0A 00 00 0B 2A 0C 30 78 0B 00 00 0E 40 0E F3 7E 0C 00 00 .*.......*.0x....@..~...
000001B0 0B 2A 0C 0B 32 0D 00 00 0E 00 0E 99 F4 12 00 00 0C B9 0D 7D 30 12 00 00 .*..2..............}0...
000001C8 0B 30 0D E7 8E 13 00 00 0C 80 10 AA 46 16 00 00 0B 30 0C CB 70 1A 00 00 .0..........F....0..p...
000001E0 0B 30 0F CA 0C 1C 00 00 0B 30 0F C5 A6 20 00 00 0B 30 10 8D AE 27 00 00 .0.......0... ...0...'..
000001F8 0B 30 0E 80 0C 2D 00 00 0B 30 0C 55 BE 31 00 00 F8 00 F8 8E E4 32 00 00 .0...-...0.U.1.......2..
00000210 0B 30 0D 3D 8A 33 00 00 0B 30 0F 28 2E 36 00 00 0B 30 0F C7 26 3A 00 00 .0.=.3...0.(.6...0..&:..
00000228 0B 30 0E 5E BE 3E 00 00 0B 30 0F B2 EC 41 00 00 0B 30 0F C2 6E 46 00 00 .0.^.>...0...A...0..nF..
00000240 0B 30 0F 51 00 4B 00 00 0B 30 0F 9B 22 4F 00 00 0B 30 0F 3E 8E 53 00 00 .0.Q.K...0.."O...0.>.S..
00000258 0B 30 0F 3C 9C 57 00 00 0B 30 0D C6 A8 5B 00 00 0B 30 10 AE 3E 5E 00 00 .0.<.W...0...[...0..>^..
00000270 0B 30 10 40 BC 63 00 00 0B 30 0D 71 CC 68 00 00 0B 30 10 8F 0E 6B 00 00 .0.@.c...0.q.h...0...k..
00000288 0B 30 0D E1 BE 72 00 00 0B 30 0D ED 70 75 00 00 0B 30 0E 72 2E 78 00 00 .0...r...0..pu...0.r.x..
000002A0 0B 30 0E 24 70 7B 00 00 0B 30 0F 93 64 7E 00 00 0B 30 0D 7D C8 82 00 00 .0.$p{...0..d~...0.}....
000002B8 0B 30 0B 9A D4 89 00 00 0B 30 0E 64 16 85 00 00 0B 30 0B 87 4A 88 00 00 .0.......0.d.....0..J...
000002D0 0B 30 0C 61 A2 88 00 00 0B 30 0C 91 5C 30 00 00 0B 30 0E 5A 3E 8A 00 00 .0.a.....0..\0...0.Z>...
000002E8 0B 30 0F C8 68 8D 00 00 0B 30 0D 0D 00 92 00 00 0B 30 0D A2 3C 25 00 00 .0..h....0.......0..<%..
00000300 0B 2A 0B FA 60 11 00 00 0B 30 0D 80 6E 70 00 00 0B 30 0F 43 DE 93 00 00 .*..`....0..np...0.C....
00000318 2D 45 6E 64 54 62 6C 2D 43 80 40 43 F9 40 00 00 00 00 00 E5 80 54 40 70 -EndTbl-C.@C.@.......T@p

Hi, digging through the junk pile today I discovered a DPF I bought some time ago but gave up on.
No success with the current firmwares either, so perhaps you would like to add it to your list?

It is marked as Model XG4241 and sold by DSE in Australia (and New Zealand?).

http://dicksmith.com.au/product/XG4241/dick-smith-1-5-quot-digital-photo-frame-keyring
http://dicksmith.com.au/media/DSAU/Media/static/WebDocumentCollection/Manuals/XG4241_Manual.pdf

marcus@xps:~/src/dpf/dpf-ax/trunk/fw$ sudo python identify.py /dev/sg11
Detecting & reading dpf flash...
Opening generic SCSI device '/dev/sg11'
Manufacturer: Winbond
Size        : 2 MB
Reading 200000 bytes...
Flash written to file 'identify.out/full.bin'.

Looking for firmware.............: Found (coby, 128x128 px).
Looking for Openwin..............: Found.
Looking for LcdIniTbl............: None.
WARNING: This is no "standard" buildwin software!
Looking for known signatures.....: None.
Looking for known version info...: None.

Sorry, no matching dpf found.

marcus@xps:~/src/dpf/dpf-ax/trunk/fw$ sudo lsusb -v -d 1908:0102

Bus 002 Device 112: ID 1908:0102 GEMBIRD 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0         8
  idVendor           0x1908 GEMBIRD
  idProduct          0x0102 
  bcdDevice            2.00
  iManufacturer           2 BUILDWIN
  iProduct                3 Digital Photo Frame
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              200mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk-Only
      iInterface              4 DPF Mate
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
Device Status:     0x0000
  (Bus Powered)

Regards,
Marcus.

@dkrusko

Please try this fw.
Do you have a manufacturer/seller name and/or a link? If not, this one will stay "acme_3"...

I'm not sure if this fw will work. Looks a lot like the last one from Papa Oscar (which is nor working atm). I'm still waiting for my display from linkdelight to have a closer look.

superelchi

@markusbrutus

WOW! As identify.py said: This is no "standard" buildwin software!
It has a completely different LdInit-Routine and does NOT use the OTP lcd write routine.
Maybe you found the first truly "not supported" type. ;-)

You can try attached fw but this is only an educated guess.
If this will not work I see no possiblity to support this one in the near future. Sorry.

superelchi

@superelchi

i will give it a go tonight and let you know if it is working.

No manufacturer on the case anywhere it was purchased from eBay here is link:

http://www.ebay.com/itm/400391394538?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649

If you think that it can help i can open it up and get board and chips pictures.



Thanks Davor


I just tried uploaded firmware and after reboot LCD is staying black I will preform couple more test tonight and edit post accordingly

Thanks



Edited 1 time(s). Last edit at 02/18/2013 02:01PM by dkrusko.

@superelchi

marcus@xps:~/src/dpf/dpf-ax/trunk/fw$ sudo ./hiddetach && sudo python restore.py ../src/fw_xg4241.bin -f
Detaching dpf at 2-1:1.0... done.
Found AX206 DPF (bootloader)
Manufacturer: Winbond
Size        : 2 MB
Erase full flash...
Flashing sector 0...
Flashing sector 1...
Flashing sector 2...
Flashing sector 3...
Executing applet..

Doesn't work ... backlight on, white background and still says "USB Connect" (pale) even after a reset.
Not to worry, thanks for trying.