DPF(LCD Display) automatic reattach question November 29, 2012 08:26PM |
Registered: 11 years ago Posts: 7 |
[12202.720000] usb 1-2: new full speed USB device using oxnas-ehci and address 4 [12217.840000] usb 1-2: device descriptor read/64, error -110 [12233.070000] usb 1-2: device descriptor read/64, error -110 [12233.300000] usb 1-2: new full speed USB device using oxnas-ehci and address 5 [12248.420000] usb 1-2: device descriptor read/64, error -110 [12263.650000] usb 1-2: device descriptor read/64, error -110 [12263.880000] usb 1-2: new full speed USB device using oxnas-ehci and address 6 [12274.300000] usb 1-2: device not accepting address 6, error -110 [12274.420000] usb 1-2: new full speed USB device using oxnas-ehci and address 7 [12284.840000] usb 1-2: device not accepting address 7, error -110 [12284.840000] hub 1-0:1.0: unable to enumerate USB device on port 2 [12345.740000] usb 1-2: new high speed USB device using oxnas-ehci and address 8 [12345.890000] usb 1-2: configuration #1 chosen from 1 choice [12345.890000] scsi2 : SCSI emulation for USB Mass Storage devices [12345.910000] usb-storage: device found at 8 [12345.910000] usb-storage: waiting for device to settle before scanning [12350.910000] scsi 2:0:0:0: Direct-Access USBest USB2FlashStorage 0.00 PQ: 0 ANSI: 2 [12350.920000] usb-storage: device scan complete [12350.920000] sd 2:0:0:0: [sdb] 2048000 512-byte logical blocks: (1.04 GB/1000 MiB) [12350.930000] sd 2:0:0:0: [sdb] Write Protect is off [12350.940000] sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00 [12350.940000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [12350.950000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [12350.950000] sdb: sdb1 [12351.100000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [12351.110000] sd 2:0:0:0: [sdb] Attached SCSI removable disk [12371.900000] usb 1-2: USB disconnect, address 8 [12424.470000] usb 1-2: new full speed USB device using oxnas-ehci and address 9 [12439.590000] usb 1-2: device descriptor read/64, error -110USB LCD display reattach failure but usb-storage success.
[20793.980000] usb 1-2: USB disconnect, address 2 [20794.290000] usb 1-2: usbfs: usb_submit_urb returned -19 [20795.180000] usb 1-2: new full speed USB device using oxnas-ehci and address 3 [20795.360000] usb 1-2: configuration #1 chosen from 1 choice [21688.580000] usb 1-2: usbfs: process 12098 (lcd4linux) did not claim interface 0 before use
lcd4linux.c: got signal 1 lcd4linux.c: leaving main loop DPF: shutting down. drv_dpf.c: closing connection lcd4linux.c: restarting...
Re: DPF(LCD Display) automatic reattach question December 03, 2012 06:53AM |
Registered: 11 years ago Posts: 61 |