After download this two files and remove the disk: _ _ _ _ | | | | | | | | ___| |__ _ _| |_| |_| | ___ / __| '_ \| | | | __| __| |/ _ \ \__ \ | | | |_| | |_| |_| | __/ |___/_| |_|\__,_|\__|\__|_|\___| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |__by Jacq - Debian
When i remove prepared disk from the omninas uboot isn't loading(from nand)....by Jacq - Debian
How to repair console permanently?by Jacq - Debian
Ok, it was problem with connectivity between pins and mainboard... How to repair console permanently? Can you share me files for booting debian from disk?by Jacq - Debian
UART converter/serial is working properly on other device - Zyxel NSA310by Jacq - Debian
Now power button blink on violet/red. Nas get up from dhcp, but no response on icmp.. Console still not working...by Jacq - Debian
I configure dhcp and tftp server option, but omninas did not try to get ip from this server.... Any idea?by Jacq - Debian
@Peacemaker I prepared disk with only one partition(with ext3 file system) using your script and i have put disk into right bay. > Btw.: Is your kd20 still beeping after power it up? Yes and blue power button changed color to red. Console still don't work...by Jacq - Debian
@Peacemaker Are you sure that your suggestion should be working when i have not work console...? How can I verify results without console?by Jacq - Debian
I cannot start linux on my omninas. Uboot is not booting...by Jacq - Debian
@Peacemaker Unfortunately I do not have access via ssh. > If you are not able to do this, you can boot into uboot via SATA and reflash your Uboot, if you need to do this I'll upload a files for this and a manual. How can I do it?by Jacq - Debian
I wrote about Serial/UART. After connecting serial cable between UART converter and omninas conector on the console i do not see any boot information... It's looks like failure port in omninas...:/ I tried to use another serial converter, but is not working too..:/ Any idea?by Jacq - Debian
@Peacemaker Ok, this device has a problem with full support 1Gbps speed and when the server tftp serve file with full speed omninas drop packet.. After change interface speed to 100M FD everything works fine :) I had booted from usb flash drive debian from your sources but i did not saved nand parameters permanently. Unfortunately after restart i cannot communicate via console... Restartby Jacq - Debian
Peacemaker Wrote: ------------------------------------------------------- > Okay, load things from usb will not work, from > sata you can load data. How can i load this file from sata? Tftp in the same network like omninas(have still static IP) and gw has similar problem...by Jacq - Debian
It's look like: Shuttle>> setenv gatewayip 192.168.1.1; Shuttle> tftp 64000000 uImage3.18.1_7; tftp 60500000 uInitrd_w; Wait GMAC to reset Wait for PHY reset PHY is IC+ IP1001LF Wait for link to come up..........Link up Wait for auto-negotiation to complete Link is 1000M TFTP from server 213.xx.xx.xx; our IP address is 192.168.1.20; sending through gateway 192.168.1.1 Fiby Jacq - Debian
Tftp generate a lot of problems.. How to upload uImage3.18.1_7, uInitrd_w from e.g. usb memory?by Jacq - Debian
Where are the screws? I found only two near hinges..by Jacq - Debian
On the mainboard of Omninas i do not have any pin to connect uart cable(console). Do I have to solder this pins for console ?by Jacq - Debian