Awesome, glad I was able to help out. Thanks for walking me through all this.by Strix - Debian
root@mnemosyne:~# cat /proc/cmdline console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) root@mnemosyne:~# cat /proc/mtd dev: size erasesize name mtd0: 00200000 00020000 "u-boot" mtd1: 00300000 00020000 "uImage" mtd2: 00300000 00020000 "uImage2" mtd3: 00800000 00020000 "failsafeby Strix - Debian
I get this error when I try to flash_erase root@mnemosyne:~# flash_erase /dev/mtd0 0 4 flash_erase: error!: /dev/mtd0 error 13 (Permission denied)by Strix - Debian
kwboot is how it is booting. If I don't use it the pogo doesn't boot. strix@atlas-2:~/kwboot/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p Sending boot message. Please reboot the target...| Sending boot image... 0 % [+++++++++++++++++xmodem: Bad message strix@atlas-2:~/kwboot/kwboot-tool$ sudo ./kwboot -t -B 115200 /dev/ttyUSB0by Strix - Debian
Envs listing Pogov4> printenv arcNumber=3960 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $lby Strix - Debian
Ok I got the system booted via kwboot. Do you need any of the output?by Strix - Debian
Hi bodhi, USB serial part came. What's next?by Strix - Debian
http://www.ebay.com/itm/371046646242 I have extra ribbon cables similar to this: https://goo.gl/c4eZo8 Can I use them in place of getting the "Micro Mini.JST 2.0 PH 4-Pin Connector"?by Strix - Debian
Hi Bodhi, I thought you might say that. Ok, is there a serial cable I can order on amazon that I can use? Or a cable you recommend? If you have a link to instructions for how to connect to the pogo serial that would be very helpful. Here's the log of commands I did last. Linux pogo 3.18.5-kirkwood-tld-1 #1 PREEMPT Thu Feb 5 17:58:07 PST 2015 armv5tel The programs included with tby Strix - Debian
Netconsole isn't getting anything from the pogo. The light on the front of the device isn't lighting up at all either.by Strix - Debian
I found the problem I was having with nc was it was the openbsd version which doesn't allow the use of the 'l' and 'p' flags together. I think I messed up the mtdparts setting by accidentally setting it to: mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) instead of: mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(faby Strix - Debian
Could I just rollback my kernel to boot into 3.18 and fix it as part of the upgrade to 4.8.3?by Strix - Debian
I don't have a USB rootfs, my setup was with an SD card rootfs. Will this be configurable to boot using the SD card? I think the nc issue is with my distro nc. Using the command above gives a "Cannot assign requested address error". I was using the other nc method by running: nc -l -u -p 6666 & nc -u 192.168.1.20 6666by Strix - Debian
So I need to remove the mmc related envs? I was running netconsole from a linux box from a cygwin terminal so maybe that's why the interrupt won't work, I'm going to try it again from a linux terminal instead.by Strix - Debian
I did not append the DTB, I followed step 4a and then step 5. I'm using an SD card rootfs. `--> ls -lart total 51508 drwxr-xr-x 23 root root 4096 Dec 31 1969 .. -rw-r--r-- 1 root root 146396 Oct 21 01:38 config-4.8.3-kirkwood-tld-1 -rwxr-xr-x 1 root root 3232304 Oct 21 02:34 zImage-4.8.3-kirkwood-tld-1 -rw------- 1 root root 3232304 Oct 21 05:30 vmlinuz-4.8.3-kirkby Strix - Debian