bodhi Wrote: ------------------------------------------------------- > SOL, > > No, currently your bootcmd boot Archlinux but not > Debian. > > This needs to be changed > > bootcmd_linux=setenv bootargs $(bootargs_linux); > ide reset; ext2load ide 0:1 $(loadaddr) /uImage; > bootm $(loadaddr) > > to something like this: > > bootcmd_linuxby SomeoneOnLine - Debian
Sweet. Thats the answer I was hoping for. Thanks. ~SOLby SomeoneOnLine - Debian
So I got my hands on a cp2102 usb uart cable but when I broke it open I noticed that the red wire is soldered to the 5v pin in the usb plug and the 3v has nothing on it. Will that fry the controller on my nsa325 if I use the 5v wire? My usb cable only has 4wires on it. The cable I purchased is USB 2.0 to TTL Uart 6Pin Module Serial Converter CP2102 Thanks ~solby SomeoneOnLine - Debian
Thanks for the info. Good to know before I start messing around and brick my nsa325. I am trying to order a cable now. From what you can tell does my current uboot_env support booting debian in addition to archlinux? ~SOLby SomeoneOnLine - Debian
I am needing to get me a serial cable for my nsa325. I found this after digging around. Would this work for me? Generic Micro Sata Cables - USB 2.0 to TTL Uart 6Pin Module Serial Converter CP2102 ~SOLby SomeoneOnLine - Off-Topic
Just read up a little on netconsole. I like the idea. It looks like my uboot might support it. However it has the wrong IP for my network. Can I simply just change the ip to an IP I can run netcat on? If my nsa325 doesn't support net console is it difficult to make it support it? ~solby SomeoneOnLine - Debian
Below is my uboot_env. I think I got it all. bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1)$ bootdelay=2 baudrate=115200 loads_echo=0 ipaddr=10.4.52.165 serverip=10.4.52.7 rootpath=/srv/ubuntu netmask=255.255.255.0 nandEcc=1bit MODEL_ID=AA03 PRODUCT_NAME=NSA-325by SomeoneOnLine - Debian
Since I already have archlinuxarm on my nsa325 Does that mean uboot environment is already set? I don't have a serial cable so I'm nervous to mess with uboot. Can I maybe extract rootfs to sdb then swap the 2 drives in the bays around? ~solby SomeoneOnLine - Debian
Sorry for the noob question but how would one try the "Kirkwood linux-3.12 Kernel" with a debian rootfs? Do I need to get download a debian rootfs from somewhere then put the "Kirkwood linux-3.12 kernel in it some how? ~SOLby SomeoneOnLine - Debian
Thanks so much. I won't be back in town until after December 2nd. But I will definitely test and report. Thanks again for your efforts. Regards, ~SOLby SomeoneOnLine - Debian
Thanks. I was just looking for that. Just got checked into my hotel and was gonna pull it up for you. Thanks for any and all help with this topic. ;)by SomeoneOnLine - Debian
Ok. I'll read up on debootstap. I have a ghost type image of my current arch install. Maybe I'll play around a bit.by SomeoneOnLine - Debian
Thats kinda what I thought. The part that I'm not sure of is how would I go about installing it? Are there any tutorials I could read and or follow? Thanks, ~SOLby SomeoneOnLine - Debian
Might be a dumb question but has anyone been able to get this little buger to run debian? I currently have archlinuxarm installed and running just fine but was hoping to at some point run debian squeez or weezy. :) ~SOLby SomeoneOnLine - Debian