Marvell>> tftpboot 0x2000000 uImage-D Using egiga0 device TFTP from server 172.16.10.18; our IP address is 172.16.10.150 Filename 'uImage-D'. Load address: 0x2000000 Loading: ################################################################# ################################################################# #################################################by zifxify - Debian
Quote Hey, while there’s no extload commands there is tftpboot, have you tried loading the kernel from a tftp server? I'm getting following output Marvell>> setenv ipaddr 172.16.10.150 Marvell>> setenv serverip 172.16.10.18 Marvell>> tftpboot *** Warning: no boot file name; using 'AC100A96.img' Using egiga0 device TFTP from server 172.16.10.18; oby zifxify - Debian
Quote zifxify, Back to USB issue. At u-boot prompt mw 0xf10a2620 0x251 mw 0xf10a2e20 0x251 usb xhciinit And then if the USB drive is not initialized, go ahead and start it: usb start Marvell>> mw 0xf10a2620 0x251 Marvell>> mw 0xf10a2e20 0x251 Marvell>> usb xhciinit (Re)start USB controller... USB0: Port (usbActive) : 0 Interface (usbType = 3) : Uby zifxify - Debian
Quote Try kwboot with -p option. That image should be a flash-ready image (unless the documentation describes it as UART-bootable). sudo kwboot -t -B 115200 /dev/ttyS0 -b uboot_RS816.bin -p -s 0 -q 1 nothing seems to happenby zifxify - Debian
I have found a uboot_RS816.bin image after extracting the dsm pat file but kwboot seems no success so I think it's not supported either. sudo kwboot -t -B 115200 /dev/ttyS0 -b uboot_RS816.bin -s 0 -q 1 I'm using a debian 32bit laptop with serial port and kwboot from u-boot-tools.by zifxify - Debian
Quote Ok, so try to list the boot folder to verify. ext2ls usb 0:1 /boot as stated by you: neither of the commands seems to be supported by this u-boot version ext2load ext2ls fatload should uploading another u-boot version with kwboot be possible ?by zifxify - Debian
Marvell>> setenv usb 'setenv usbActive 1; setenv usbType 3; usb start;' Marvell>> run usb (Re)start USB... USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) foundby zifxify - Debian
Hi Bodhi Quote At u-boot prompt, try setenv usbActive 1 usb reset Not much progress, still the same error as the above one. Quote spi_pt_addr_dt=0x0E0000 The stock DTB is stored at this location (we could extract that). that's something good I suppose, let me know how to extract it and I will upload it to you Do you have some advice about the right boot params for tby zifxify - Debian
output of USB start, (USB stick is plugged in) Marvell>> usb start (Re)start USB... USB0: Error: requested 'usbActive' (0) is not connected on current board Supported Units: USB2.0: 1 ports: set usbType = 2 --> EHCI Stack will be used USB3.0: 2 ports: set usbType = 3 --> xHCI Stack will be used lowlevel init failed USB error: alby zifxify - Debian
I created the rootfs on a ESATA and USB compatible stick. Booting from Esata would also be nice if supported I guess :) Could it be possible that this is already done when unpacking the rootfs as there is already an zImage ? cp -a zImage-4.12.4-mvebu-tld-1 zImage Next trying some env bootargs but ext2load seems not to be supported ("unknown command") or am I doing something wrby zifxify - Debian
Hello, I would like to install Debian on my Synology NAS (RS816-inside) as a replacement for the current dsm software. It's a 4 bay rack mountable system (1GB DDR3) with an additional esata and two usb ports at the back. Furthermore I have no experience with uboot so I don't know if it's actually possible to boot debian with the stock u-boot from synology. I do not have a dtsby zifxify - Debian