Ah, I understood now. Kernel load is a difference process, it uses boot args for initial and it does't know about OS root location itself, must be set from boot args By this way we also can separate kernel and rootfs into 2 difference partitions So boot loader will find kernel and tell kernel how to boot. There is no standard for kernel name and kernel args, so it's hard to makby as247 - uBoot
Thank you so much Bodhi, I will wait for next U-boot release. And I hope that you can make it boot from first partition without need to set label "rootfs"by as247 - uBoot
Hi bodhi, pls find in attached files for full dmesg and mount result mount Quotesysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=54488k,nr_inodes=13622,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfby as247 - uBoot
Hi habibie, Look like your result is better than mine, I have never test speed before on stock firmware and on ALARM firmware, so can't compare to see if any issue with OS. I saw you tried to boot to ALARM with Bodhi's U-boot 2017, any success?. I have tried the latest ALARM image, boot console looks fine but system not up, no IP, no ssh... Quotehttps://forum.doozan.com/read.php?3by as247 - Debian
Oh I see, does that mean IDE/Sata port is divided from usb 2.0 hub? My SSD is speed limited around 50MB/s seem it matches USB 2.0 max speed :(by as247 - uBoot
I have goflex home running Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 on Colorful SL300 128GB via SATA port I just tried a dd test and speed only 47MB/s it's too slow for SSD hard disk device Quoteroot@debian:~# dd if=/dev/zero of=/output.img bs=1024k count=1k 1024+0 records in 1024+0 records out 1073741824 bytes (1.1 GB, 1.0 GiB) copied, 22.5388 s, 47.6 MB/s root@debian:~#by as247 - Debian
bodhi Wrote: ------------------------------------------------------- > Nope. That's the USB hub. It counts as a device. > When you plug in a USB drive, it will report as > another USB storage device. But i have no usb hub plugged in, is that internal hub? I have only ssd disk on sata port, nothing else regards,by as247 - uBoot
bodhi, It's hard to find, there are too many posts But it should be an issue, it always show "scanning bus 0 for devices... 1 USB Device(s) found " either USB plugged in or not regards,by as247 - uBoot
Thank bodhi, it works now. I set dtb_file to /boot/dtbs/kirkwood-goflexnet.dtb because i want to boot to ALARM, so i kept that old env. There is another question that, as you can see in above logs .uEnv.txt doesn't load from ide (ssd device) Quoteloading envs from usb 0 ... ** Bad device usb 0 ** Anyway to tell u-boot to load .uEnv.txt from ide as well if usb is not plugged in? Thaby as247 - uBoot
Hello, I have goflex home and a running lastest version of archlinuxarm here http://os.archlinuxarm.org/os/ArchLinuxARM-kirkwood-latest.tar.gz But after i installed your uboot - https://forum.doozan.com/read.php?3,12381 it not able to boot to ALARM again. I also tried to create uInitrd Quotecd /media/sdb1/boot mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initraby as247 - uBoot