THANKS! it works!! Now I have the latest uboot and Debian running by default. Thanks a lot bodhi, You really helped me.by davdav - uBoot
bodhi Wrote: ------------------------------------------------------- > > root@debian:~# dmesg | grep -i 'bad' > > [ 5.869471] Scanning device for bad blocks > > [ 5.881678] Bad eraseblock 84 at > > 0x000000a80000 > > [ 5.924175] Bad eraseblock 482 at > > 0x000003c40000 > > [ 5.947658] Bad eraseblock 680 at > > 0x000005by davdav - uBoot
ok, it works, thanks!! I can now boot into your rootfs. fw_printenv bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; runby davdav - uBoot
Now I want to be carefull.. I downloaded uboot.2017.07-tld-1.nsa325.bodhi.tar (checksum ok) I downloaded kwboot-2016.05.tar (then understood that this was for ARM devices, I am on amd64 Ubuntu) installed u-boot tools from repo, with kwboot executable inside I then run the command: sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa325.mtd0.kwb -p the output Sending boot mby davdav - uBoot
hi Bodhi (& forum too), back again after some troubles with the new year. I hope you enjoyed these days. here is the full log ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 800Mhz SysClock = 533Mhz , TClock = 200Mhzby davdav - uBoot
tried another USB pen, same result.. :(by davdav - uBoot
thanks again.. but I cannot proceed: I've downloaded the scr file and put it into boot folder run the commands like below Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 0 Storage Device(s) found Marvell>> ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.enviby davdav - uBoot
Hi bodhi, thanks for your reply. Here are the outputs: printenv Quote bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr) to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset bootcmd=&by davdav - uBoot
Hi Forum! what a pity I found you only a few hours ago. I have a NSA 325 v2: a friend told me that I can put Debian on it.. googling NSA325 debian I went to the wrong wiki :( (zyxel.nas-central.org/wiki/Debian_on_325, which is outdated). What I did: At the Marvell>> Prompt Marvell>> resetenv Marvell>> reset The device rebooted. At the Marvell>> Prompt againby davdav - uBoot