Hello. Unfortunately no. I soldered emmc to motherboard and flushed to hdd firware from other same cpu with emmc devices, it recognized my emmc but fail to boot further. Apparently different devices of same cpu are using different gpio ports so iomega HM is dead for good. There's no developer willing to create devices specific boot file to load kernel. Especially now we have raspberry pi aby sobir - Off-Topic
Hi bodhi! I tried with ox820-pogoplug-classic.dtb no luck, same thing. I'll try with oldzeus's dtb which, I suspect, is file named u-boot.md.wrapped? If no luck there then I will contact openwrt and willing to donate them my board so they can compile all u-boot needed. By the way I always have checksum verification failing with setenv uinitrd_addr '0x60e00000' seteby sobir - uBoot
Hi bodhi! I found this QuoteOpenwrt no PCIe on OX820/NAS7820, 1x PCIe on OX821/NAS7821, 2x PCIe on NAS7825 so conclusion is pogoplug pro has oxnas7821 cpu and iomega HMNHDCE, pogoplug v3 and ZyXEL NSA-212 / MitraStra STG-212 are oxnas7820 cpu. I have to try pogoplug-classicby sobir - uBoot
Hi bodhi! here is the result: U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34) Boot device: SATA Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set Bus 0: OK Device 0: ** File not found /boot/bootargs.bin ** U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for Oby sobir - uBoot
Hi everyone! Anybody have iomega storcenter ix2 or iomega home media network hard drive please take a close picture of this components here. Thees are fan support to control and reed fan speed. I need names written on tree legged transistors/diods and values of capacitors. I have iomega HMNHDCE and I want to install fan here, but I don't know what components to solder. Or better option iby sobir - Off-Topic
Hi bodhi! I did all what you instructed. my ls -larth /mnt/boot output is: total 8.3M -rwxr-xr-x 1 root root 16K Dec 31 1969 u-boot.env drwxr-xr-x 2 root root 4.0K Aug 3 2014 dts -rwxr-xr-x 1 root root 32K Aug 3 2014 u-boot-spl.bin -rw-r--r-- 1 root root 514K Aug 3 2014 u-boot.img -rw-r--r-- 1 root root 2.2M Aug 3 2014 uImage_2.6.31.14_OX820_1.2_shv.Pro -rw-r--r-- 1by sobir - uBoot
I soldered 128M nand to iomega HMNHDCE motherboard and added resistors (10 ohm resistor array). Here is picture: photo Right now I'm using oldzeus's uboot where nand is not supported. I tried new spl for pogoplug and nand was recognized (HURRAAAAAHHHH!!!!!!!). It shows 16M at first boot and 128M at reboot, I don't know why, is it normal? bodhi is helping me right now to get to sby sobir - Off-Topic
I've used them (microcenter micro sd 32 & 16 Gb class 10) a lot with rasbery pi 3 b+ in different projects like motioneyeos, openmediavault, raspbian stretch and buster. So far so good. One of usb 2.0 16Gb flash become unbootable after many time redoing partition table. Maybe corrupted blocks?by sobir - Off-Topic
hi bodhi! here is what I did today: I booted to usb wheezy from odzeus's uboot to empty hdd and here is log from screen: root@OXNAS:~$uname -a Linux OXNAS 3.12.6_OXNAS+ #1 SMP Sun Jan 12 08:07:56 CST 2014 armv6l GNU/Linux root@OXNAS:~$dd if=/dev/zero of=/dev/sda bs=1M count=34 34+0 records in 34+0 records out 35651584 bytes (36 MB) copied, 1.01906 s, 35.0 MB/s root@OXNAS:~$pby sobir - uBoot
Hello! I have iomega HMNHDCE where I have oldzeus's uboot and debian buster installed. But I can't use it with open vpn. Old kernel can't create tun. So i found this forum and used direct sata boot instructions with spl for pogoplug pro. My problem is that iomega 's ram is 256M not 128M as pogoplug so my checksum verification is failing at boot? My question is: is it possiby sobir - uBoot