SHAME ON ME ;-) dtb file is set correctly: root@debian:~# fw_printenv dtb_file dtb_file=/boot/dts/kirkwood-nsa310.dtb root@debian:~# Thanks again very much for your support. Shall I close this topic (and can I do that myself)? Kind regards, Marcby 1p21GW - uBoot
Well, I did not install anything, to be honest. Didn't know I should have...by 1p21GW - uBoot
Sorry again for the newbie question: But fw_setenv and fw_printenv yield "command not found"... (but the variable is set correctly in the u-boot console. I checked.by 1p21GW - uBoot
Great. So I change the dtb_file and then saveenv to have it permanently?by 1p21GW - uBoot
NSA310> setenv dtb_file /boot/dts/kirkwood-nsa310.dtb NSA310> printenv dtb_file dtb_file=/boot/dts/kirkwood-nsa310.dtb NSA310> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) Use USB retry period from the environment: 15 second(s)by 1p21GW - uBoot
BTW: I did that before you sent your reply with the typo ;-)by 1p21GW - uBoot
bodhi, I adapted your suggestion a bit and did this: NSA310> setenv dtb_file /boot/dts/kirkwood-nsa310a.dtb NSA310> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) Use USB retry period from the environment: 15 second(s) 2 Storage Devby 1p21GW - uBoot
NSA310> setenv dtb_file /boot/dts/kirkwood-nsa.dtb NSA310> printenv arcNumber=4022 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 orion_nand:0x100000(uboot),0x80000(uboot_env) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $by 1p21GW - uBoot
Ok, here we go: U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:54:15 -0700) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA310> NSA310> boot starting USB...by 1p21GW - uBoot
Hi bodhi, Thanks for your reply and support. Here's the result (I already tried something similar): nano /etc/network/interfaces: auto lo enp1s0 iface lo inet loopback #allow-hotplug egiga0 #iface lo inet loopback iface enp1s0 inet dhcp #hwaddress ether fc:f5:28:76:ae:de The entries that are commented out are from other tries I made (incl the MAC address). Rebooted and unfortunateby 1p21GW - uBoot
Hello all, I've been trying to re-use my old Zyxel NSA310 with u-boot, Debian and OMV as application (open media vault). First attempt was not succesful, I had to start from the very beginning again. I've managed to install u-boot now and Debian - so far so good. BUT: There is no network adapter present, which isn't really helpful :( Here's some info: U-Boot 2017.07-tld-by 1p21GW - uBoot