For version 2025.01-rc1-ge61ea9f2e5d2-dirty not work piotr@PC-Kubuntu-01:~/Pobrane/U-boot/NSA320$ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p kwboot version 2025.01-rc1-ge61ea9f2e5d2-dirty Detected kwbimage v0 with NAND boot signature Patching image boot signature to UART Sending boot message. Please reboot the target.../ - \^C For version 2024.01by petecom - Debian
Zyxel NSA320S Step 1: Connect the CP2102 USB to UART Bridge Controller to the USB HUB using ONLY three pins RX to TX TX to RX GND to GND Step 2: Launch the console on your computer and go to the location where you saved the files. cd Downloads/U-boot/NSA320S Type and execute the command: sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p The followingby petecom - Debian
Zyxel NSA320S sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p USB-UART flashing extra blue led and kwboot version 2024.01 Detected kwbimage v0 with NAND boot signature Patching image boot signature to UART Sending boot message. Please reboot the target...| How long to wait? What's next?by petecom - Debian
OK. 01. Type sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p kwboot version 2024.01 Detected kwbimage v0 with NAND boot signature Patching image boot signature to UART Sending boot message. Please reboot the target...| How long to wait. Will it end? Should I stop it? Och no! /Failed to send message pattern: Input/output errorby petecom - Debian
A few basic questions 1. I bought another M2 drive for my computer and installed KUBUNTU 24.10 on it Info: KDE Plasma Version: 6.1.5 KDE Frameworks Version: 6.6.0 Qt Version: 6.6.2 Kernel Version: 6.11.0-21-generic (64-bit) Graphics Platform: Wayland Processors: 24 × 12th Gen Intel® Core™ i9-12900KS Memory: 31.1 GiB of RAM Graphics Processor: NVIDIA GeForce Rby petecom - Debian
What to do if I have deleted everything? Even connecting via USB-TTY adapter does not cause any reaction. Only the power LED lights up, the fan works. No reaction. I have probably deleted the entire contents of the NAND memory Is it still possible to save my NSA320?by petecom - Debian
In the screenshots I have attached the situation after connecting USB to TTL and executing the kwboot command Does this mean that the board is completely screwed up?by petecom - uBoot
Have I completely damaged the Zyxel NSA320S? There is currently no reaction, The blue LED lights up when I connect the power supply. You do not turn on, you do not react... Brak połączenia po COMby petecom - uBoot
That's all I understood from the instructions... You then write something about executing dpkg -i from *.deb but where what and how on a virtual machine, on a pendrive, exactly where? Then you say rootfs make a uimage, someone writes that they named the partition rootfs (I know you can) I would like some logic in the instructions, assuming that the world does not end on Debian - thereby petecom - uBoot
It's completely unresponsive again, I don't know what I did wrong, but I'm asking for help...by petecom - uBoot
Hello, Small steps forward... This is how my NSA320S is currently running __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| |by petecom - uBoot
1) Put another USB in Front USB port with kernel 2) Open in Putty 3) Power on the Zyxel NSA320S and what next....????by petecom - uBoot
You'll need a Linux system to unbrick this box. In Windows 11: 1) Connect to your computer with Windows 11 to USB port --> AZDelivery CP2102 HW-598 USB auf Serial Adapter CP2102 2) Install Drivers and check number of COM port (devmgmt.msc) 3) Install Software Putty on Windows 11 4) Run Putty on COM Terminal COM# (installed on Windows) and Baudrate (115200)by petecom - uBoot
Can I revive (reanimate) the NSA320S, please provide some tutorial that will allow me to create a pendrive or upload Debian via com to the NSA320S memory. This is how I disassembled it to its first parts. I need to do this with a computer with Windows 11 Pro to useby petecom - uBoot