u-boot via uart on mvebu June 02, 2017 02:45PM |
Registered: 6 years ago Posts: 119 |
u-boot-a38x-Yosemite_2014T3_PQ-nand.bin u-boot-a38x-Yosemite_2014T3_PQ-nand-uart.bin
./kwboot -t -B 115200 /dev/ttyUSB0 -b u-boot-spl.kwb Sending boot message. Please reboot the target.../ Sending boot image... 0 % [+++++++++++++++++xmodem: Bad message
============================================================================================== Marvell doimage Tool version 2.10 Supported SoC devices: Marvell Armada and xCAT series ============================================================================================== Usage: doimage <mandatory_opt> [other_options] [bootrom_output] <image_in> <image_out> [header_out] <mandatory_opt> - can be one or more of the following: ============================================================================================== -T image_type: sata\uart\flash\bootrom\nand\hex\bin\pex\mmc -D image_dest: image destination in dram (in hex) -E image_exec: execution address in dram (in hex) if image_type is 'flash' and image_dest is 0xffffffff then execution address on the flash -S image_source: if image_type is sata then the starting sector of the source image on the disk if image_type is flash\nand then the starting offset of the source image at the flash - optional for flash\nand -W hex_width : HEX file width, can be 8,16,32,64 -M twsi_file: ascii file name that contains the I2C init regs set by h/w. this is used in i2c boot only The following options are mandatory for NAND image type: ----------------------------------------------------------------------------------------------- -L nand_blk_size:NAND block size in KBytes (decimal int in range 64-16320) This parameter is ignored for flashes with 512B pages Such small page flashes always use 16K block sizes -N nand_cell_typ:NAND cell technology type (char: M for MLC, S for SLC) -P nand_pg_size: NAND page size: (decimal 512, 2048, 4096 or 8192) Secure boot mode options - all options are mandatory once secure mode is selected by Z switch: ----------------------------------------------------------------------------------------------- -Z [prv_key_file]: Create image with RSA signature for secure boot mode If the private key file name is missing, a new key pair will be generated and saved in files named rsa_prv.key and rsa_pub.key A new file named sha2_pub.txt will be generated for a public key -J jtag_delay: Enable JTAG and delay boot execution by "N" ms -B hex_box_id: Box ID (hex) - from 0 to 0xffffffff -F hex_flash_id: Flash ID (hex) - from 0 to 0xffff [other_options] - optional and can be one or more of the following: ============================================================================================== -A [aes_key_file]: Valid in secure mode only. Encrypt the boot image using AES-128 key If the aes key file name is missing, a new AES-128 key will be generated and saved in file named aes_key.txt suitable for eFuse storage -G exec_file: ascii file name that contains binary routine (ARM 5TE THUMB) to run before the bootloader image execution. The routine must contain an appropriate code for saving all registers at the routine start and restore them before return from the routine -R dram_file: ascii file name that contains the list of dram regs -C hdrs_file: ascii file name that defines BIN/REG headers order and their sources -X pre_padding_size (hex) -Y post_padding_size (hex) -H header_mode: Header mode, can be: -H 1 : will create one file (image_out) for header and image -H 2 : will create two files, (image_out) for image , (header_out) for header -H 3 : will create one file (image_out) for header only -H 4 : will create one file (image_out) for image only [bootrom_output] - optional and can be one or more of the following: ============================================================================================== -p Disable BootROM messages output to UART port (enabled by default) -b baudrate Set BootROM debug port UART baudrate value = 2400,4800,9600,19200,38400,57600,115200 (use default baudrate is omitted) -u port_num Set BootROM debug port UART number value = 0-3 (use default port if omitted) -m mpp_config Select BootROM debug port MPPs configuration value = 0-7 (BootROM-specific) Command examples: doimage -T hex -W width image_in image_out doimage -T bootrom image_in image_out doimage -T resume image_in image_out doimage -T sata -S sector -D image_dest -E image_exec [other_options] image_in image_out header_out doimage -T flash -D image_dest -E image_exec [-S address] [other_options] image_in image_out doimage -T pex -D image_dest -E image_exec [other_options] image_in image_out doimage -T nand -D image_dest -E image_exec [-S address] -P page_size -L 2 -N S [other_options] image_in image_out doimage -T uart -D image_dest -E image_exec [other_options] image_in image_out doimage -T pex -D image_dest -E image_exec [other_options] image_in image_out
Re: u-boot via uart on mvebu June 02, 2017 03:09PM |
Admin Registered: 13 years ago Posts: 18,574 |
Re: u-boot via uart on mvebu June 02, 2017 03:13PM |
Admin Registered: 13 years ago Posts: 18,574 |
./kwboot -t -B 115200 /dev/ttyUSB0 -b u-boot-spl.kwb -p
Re: u-boot via uart on mvebu June 02, 2017 03:16PM |
Admin Registered: 13 years ago Posts: 18,574 |
Re: u-boot via uart on mvebu June 02, 2017 03:31PM |
Registered: 6 years ago Posts: 119 |
Re: u-boot via uart on mvebu July 04, 2017 03:53AM |
Registered: 6 years ago Posts: 119 |
Re: u-boot via uart on mvebu July 04, 2017 04:36AM |
Admin Registered: 13 years ago Posts: 18,574 |
Re: u-boot via uart on mvebu July 05, 2017 02:26PM |
Admin Registered: 13 years ago Posts: 18,574 |