Cant boot from Nand or USB Stick, please Help!!

Morning,

i have got a big problem.
I can´t boot my dockstar, neither from nand or usb stick.
Connect the dockstar over serial cable, i get this information.
But now what i have to do to boot from Nand???PogoPlug??

U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>
Marvell>> help

Big thanks for help!!



Edited 1 time(s). Last edit at 11/08/2010 02:35AM by switchgott.

> Hit any key to stop autoboot: 0

Did you hit any key? If 'yes' please do not and post the new log.

I have the same problem, but not sure how to resolve it.

U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI error: ubi_read_volume_table: the layout volume was not found
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -22
UBI init error -22
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...


U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI error: ubi_read_volume_table: the layout volume was not found
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -22
UBI init error -22
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...


U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>



Edited 1 time(s). Last edit at 11/11/2010 01:43AM by zturbo.

ZTurbo,

How did you fix it? Same thing happened to me. I "fixed" it using the older posted methodology. It hangs now when booting.

I did the following:

Quote

Marvell>> setenv bootcmd 'nand read.e 0xc00000 0x2500000 0x40000; go 0xc00000'
Marvell>> setenv ipaddr 192.168.244.190
Marvell>> setenv serverip 192.168.244.190
Marvell>> setenv netmask 255.255.255.128
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...
Erasing at 0xc0000 -- 100% complete.
Writing to Nand... done
Marvell>> nc -lu 6666
Unknown command 'nc' - try 'help'
Marvell>> reset

and get the following upong reboot (so it really bricked now).

Quote

U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x2500000, size 0x40000
262144 bytes read: OK
## Starting application at 0x00C00000


U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x2500000, size 0x40000
262144 bytes read: OK
## Starting application at 0x00C00000 ......

I used http://plugapps.com/index.php5?title=Hardware:_Seagate_DockStar_Reflashing to reflash back to factory.

http://www.yourwarrantyisvoid.com/download-files

Hope it helps

Thanks again zturbo.

I waited a bit for a couple of 16Gb micro SD cards and redid my installation. All is well now.

I have it booting OS via USB microSD card and have been installing new software everyday.