|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 12, 2020 05:35AM |
Registered: 4 years ago Posts: 49 |
Results from reformatting with GPT :
here serial console logs.
here serial console logs.
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv bootcmd 'run dt_bootcmd_usb'
OX820 # setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
OX820 # setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
OX820 # setenv usb_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run dt_usb_load_dtb; run dt_bootm'
OX820 # setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv uimage_addr 0x60500000
OX820 # setenv dtb_addr 0x62c00000
OX820 # boot
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 358 ms (12.3 MiB/s)
4594376 bytes read in 335 ms (13.1 MiB/s)
7816 bytes read in 172 ms (43.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Akitio MyCloud mini
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008337] Console: colour dummy device 80x30
[ 0.012894] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.072586] pid_max: default: 32768 minimum: 301
[ 0.077422] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084124] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092049] Initializing cgroup subsys net_cls
[ 0.096624] CPU: Testing write buffer coherency: ok
[ 0.102010] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.239938] Brought up 2 CPUs
[ 0.242984] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.250122] devtmpfs: initialized
[ 0.259018] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.268963] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.275445] prandom: seed boundary self test passed
[ 0.284769] prandom: 100 self tests passed
[ 0.288939] pinctrl core: initialized pinctrl subsystem
[ 0.295040] NET: Registered protocol family 16
[ 0.300129] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.329822] cpuidle: using governor ladder
[ 0.359815] cpuidle: using governor menu
[ 0.369141] gpio-oxnas 44000000.gpio: at address d0848000
[ 0.375027] gpio-oxnas 44100000.gpio: at address d084a000
[ 0.381148] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.400611] vgaarb: loaded
[ 0.403852] SCSI subsystem initialized
[ 0.408501] usbcore: registered new interface driver usbfs
[ 0.414223] usbcore: registered new interface driver hub
[ 0.419740] usbcore: registered new device driver usb
[ 0.425085] pps_core: LinuxPPS API ver. 1 registered
[ 0.430146] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.439365] PTP clock support registered
[ 0.445521] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.470545] NET: Registered protocol family 2
[ 0.475827] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.482938] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.489474] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.496007] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.501954] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.508528] NET: Registered protocol family 1
[ 0.513507] RPC: Registered named UNIX socket transport module.
[ 0.519490] RPC: Registered udp transport module.
[ 0.524295] RPC: Registered tcp transport module.
[ 0.529064] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.535943] Unpacking initramfs...
[ 1.013504] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[ 1.020961] Initialise system trusted keyring
[ 1.038745] zbud: loaded
[ 1.046722] NFS: Registering the id_resolver key type
[ 1.051996] Key type id_resolver registered
[ 1.056245] Key type id_legacy registered
[ 1.060410] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.067174] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.074554] fuse init (API version 7.23)
[ 1.080645] Key type big_key registered
[ 1.084858] alg: No test fo▒ cipher_null (cipher_null-generc)
[ 1.091852] alg: hash: Test▒4 failed for sha256-gener▒c
[ 1.097144] 00000000:▒
[ 1.099576] 00000010:▒
[ 1.102443] alg: hash: Test▒4 failed for sha224-generi4
[ 1.107737] 00000000:▒14 3b e0 cd 7e c5 49 5e 42 b0 de 30 cb bd 14 20
[ 1.114319] 00000010:▒20 b4 c5 58 3c ba 7d 04 f8 90 7f 8c
[ 1.120130] alg: No test fo aes (aes-gener▒c)
[ 1.124884] alg: cipher: Test 1 failed on encryption for arc4-generc
[ 1.131463] 00000000:▒75 b7 87 80 99 94 c5 96
[ 1.136158] alg: skcipher: Test 3 failed (invalid result) o▒ encryption for▒ecb(arc4)-gener▒c
[ 1.144837] 00000000:▒de 18 89 41 a3 00 5d 3a
[ 1.150133] alg: comp: Compression test 1 failed fo deflate-generi▒: output len = ▒5
[ 1.159024] alg: comp: Decompression test 1 failed for lzo-generi
[ 1.165386] 00000000:54 68 69 73 20 64 6f 63 75 6d 65 6e 74 20 64 65
[ 1.171973] 00000010:73 63 72 69 62 65 73 20 61 20 63 6f 6d 70 72 65
[ 1.178470] 00000020:73 73 69 6f 6e 20 6d 65 74 68 6f 64 20 62 61 73
[ 1.185057] 00000030:65 64 20 6f 6e 20 74 68 65 20 4c 5a 4f 20 63 6f
[ 1.191623] 00000040:6d 70 72 65 73 73 69 6f 6e 20 61 6c 67 6f 72 69
[ 1.198120] 00000050:74 68 6d 2e 20 20 54 68 69 73 20 64 6f 63 75 6d
[ 1.204677] 00000060:65 6e 74 20 64 69 66 69 6e 65 73 20 74 68 65 20
[ 1.211200] 00000070:61 70 70 6c 69 63 61 74 69 6f 6e 20 6f 66 20 74
[ 1.217694] 00000080:
[ 1.220139] 00000090:▒
[ 1.313730] DRBG: could not allocate digest TFM handle: hmac(sha256
[ 1.320197] alg: drbg: Failed to reset rn
[ 1.324367] alg: drbg: Tests0 failed for drbg_pr_hmac_sha25
[ 1.355888] DRBG: could not allocate digest TFM handle: hmac(sha256
[ 1.362352] alg: drbg: Failed to reset rn
[ 1.366517] alg: drbg: Test0 failed for drbg_nopr_hmac_sha256
[ 1.375201] alg: hash: Chunking tes_ 1 failed for ghash-gener▒c
[ 1.381253] 00000000:eb 0e 81 5c b8 e1 32 df d0 70 db 36 bb 40 21 76
[ 1.387824] Key type asymmetric registered
[ 1.392158] Asymmetric key parser 'x509' registered
[ 1.397222] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.404769] io scheduler noop registered
[ 1.408768] io scheduler deadline registered
[ 1.413242] io scheduler cfq registered (default)
[ 1.418695] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.426682] console [ttyS0] disabled
[ 1.430497] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.439124] console [ttyS0] enabled
[ 1.439124] console [ttyS0] enabled
[ 1.446225] bootconsole [earlycon0] disabled
[ 1.446225] bootconsole [earlycon0] disabled
[ 1.466373] loop: module loaded
[ 1.472286] scsi host0: sata_oxnas
[ 1.476426] scsi host1: sata_oxnas
[ 1.480291] ata1: SATA max UDMA/133 irq 7
[ 1.484290] ata2: SATA max UDMA/133 irq 7
[ 1.488378] sata_oxnas: resetting SATA core
[ 1.489584] nand: Could not find valid ONFI parameter page; aborting
[ 1.489625] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[ 1.489630] nand: Hynix NAND 256MiB 3,3V 8-bit
[ 1.489640] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.489658] Scanning device for bad blocks
[ 1.654991] 2 ofpart partitions found on MTD device 41000000.nand
[ 1.661086] Creating 2 MTD partitions on "41000000.nand":
[ 1.666467] 0x000000000000-0x0000026c0000 : "boot"
[ 1.673154] 0x0000026c0000-0x000010000000 : "ubi"
[ 1.680514] oxnas-gmac 40400000.ethernet: no reset control found
[ 1.686502] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 1.691563] Ring mode enabled
[ 1.694604] DMA HW capability register supported
[ 1.699105] Enhanced/Alternate descriptors
[ 1.703459] Enabled extended descriptors
[ 1.707448] RX Checksum Offload Engine supported (type 2)
[ 1.712926] TX Checksum insertion supported
[ 1.717171] Wake-Up On Lan supported
[ 1.720844] Enable RX Mitigation via HW Watchdog Timer
[ 1.750200] libphy: stmmac: probed
[ 1.753597] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 1.760076] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 1.766812] PPP generic driver version 2.4.2
[ 1.771781] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.778296] ehci-pci: EHCI PCI platform driver
[ 1.783339] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 1.788843] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 1.796738] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 1.819804] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 1.826117] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.832921] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.840135] usb usb1: Product: EHCI Host Controller
[ 1.844992] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[ 1.851422] usb usb1: SerialNumber: 40200100.ehci
[ 1.857098] hub 1-0:1.0: USB hub found
[ 1.860994] hub 1-0:1.0: 2 ports detected
[ 1.866099] usbcore: registered new interface driver cdc_acm
[ 1.871841] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.880030] usbcore: registered new interface driver cdc_wdm
[ 1.885839] usbcore: registered new interface driver usb-storage
[ 1.892055] usbcore: registered new interface driver usbserial
[ 1.897943] usbcore: registered new interface driver usbserial_generic
[ 1.904545] usbserial: USB Serial support registered for generic
[ 1.910978] mousedev: PS/2 mouse device common for all mice
[ 1.916702] i2c /dev entries driver
[ 1.921377] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.926986] usbcore: registered new interface driver usbhid
[ 1.932636] usbhid: USB HID core driver
[ 1.938472] NET: Registered protocol family 10
[ 1.944389] sit: IPv6 over IPv4 tunneling driver
[ 1.950103] NET: Registered protocol family 17
[ 1.954713] Key type dns_resolver registered
[ 1.960668] registered taskstats version 1
[ 1.964787] Loading compiled-in X.509 certificates
[ 1.975726] zswap: default compressor lzo not available
[ 1.981020] zswap: pool creation failed
[ 1.994913] UBIFS error (pid 1): cannot initialize compressor lzo, error -2
[ 2.016883] encrypted_key: could not allocate crypto hmac(sha256)
[ 2.039966] ▒ata1: SATA link up 1.5 Gbps (SStatus 11▒ SControl 310)
[ 2.047165] ▒ata1.00▒ ATA-8:HGST HTS545050A7E680, GR2OA230, max UDMA/13
[ 2.054069] ▒ata1.007 976773168 sectors, multi 16: LBA48 NCQ (dept
[ 2.061299] ▒ata1.00▒ configured for UDMA/13▒
[ 2.066437] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[ 2.076449] sata_oxnas: resetting SATA core
[ 2.076477] s▒ 0:0:0:▒: [sda]
[ 2.076487] s▒ 0:0:0:▒: [sda]
[ 2.077009] s▒ 0:0:0:▒: [sda]▒Write Protect i
[ 2.077248] s▒ 0:0:0:▒: [sda]▒Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.129940] sata_oxnas: resetting SATA coe
[ 2.179801] usb 1-2: new high-speed USB device number 2 using oxnas-ehci
[ 2.330885] usb 1-2: New USB device found, idVendor=0781, idProduct=5567
[ 2.337566] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.344755] usb 1-2: Product: Cruzer Blade
[ 2.348833] usb 1-2: Manufacturer: SanDisk
[ 2.352965] usb 1-2: SerialNumber: 4C530000130118211511
[ 2.359344] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 2.366072] scsi host2: usb-storage 1-2:1.0
[ 2.809802] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.899983] ata1: exception Emask 010 SAct 0x0 SErr 0x0 action 0xe frozen
[ 2.907018] ▒ata1: hard resetting link
[ 3.371361] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[ 3.381212] sd 2:0:0:0: [sdb] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 3.390666] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.396328] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3.427704] sdb: sdb1
[ 3.433950] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 3.819973] ▒ata1: SATA link up 1.5 Gbps (SStatus 11▒ SControl 310)
[ 3.828134] ata1.00Q configured forUDMA/13
[ 3.832486] ▒ata1: EH compleDe
[ 4.146644] ▒sda: detected capacity change from 0 to4500107862016
[ 4.153738] s▒ 0:0:0:: [sda]iAttached SCSI disk
[ 4.158784] Freeing unused kernel memory: 224K (c0828000 - c0860000)
[ 4.167718] Kernel panic - not syncing: Attempted to kill init! exitcode=
[ 4.174487] ▒CPU: 1 PID: 1 Comm: ini▒ Not tainted 4.4.54-oxnas-tld-1▒#2
[ 4.181150] ▒Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[ 4.187842] [c0010c6>] (unwind_backtrace) from [<c000cf8c>]▒(show_stack+0x10/0x14)
[ 4.195560] [c000cf8>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[ 4.202754] [c02cf84>] (dump_stack) from [<c0091c78>] (pani▒+0x8c/0x1ec)
[ 4.209602] [c0091c7>] (panPc) from [<c001a5f0>] (do_exit+0x9b)
[ 4.215669] [c001a5f>] (do_exit) from [<c001b600>] ▒do_group_exi)
[ 4.221913] [c001b60>] (do_group_ex▒t) from [<c002452c>] (get_signal+0x200/0x5ec)
[ 4.229539] [c002452>] (get_signal) from [<c000c72c>] (do_signal+0x▒4/0x3b0)
[ 4.236730] [c000c72>] (do_signal) from [<c000cbcc>] (do_work_pending+0x94)
[ 4.243837] [c000cbc>] (do_work_pending) from [<c000a4ac>] ▒slow_work_pending+0x)
[ 4.251463] CPU0: stopping
[ 4.254169] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.54-oxnas-tld-1 #2
[ 4.261089] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[ 4.267601] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[ 4.275315] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[ 4.282513] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[ 4.289879] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[ 4.297418] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[ 4.304860] Exception stack(0xc0861f50 to 0xc0861f98)
[ 4.309890] 1f40: 00000001 00000000 00000000 00000000
[ 4.318031] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[ 4.326167] 1f80: 0000000c c0861fa0 c000af3c c000af40 60000013 ffffffff
[ 4.332756] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[ 4.340124] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[ 4.348357] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[ 4.356500] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 12, 2020 05:51AM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
I don't think it is a bad stick. Perhaps this kernel version is not good for the Akitio yet.
Your log is hard to read, with all the escape characters mingled in the text. But errors showed some coherency errors.
Let's wait a few days when I can create a new buster rootfs and then you can try with kernel 4.14.x on the new rootfs (Or I can upload the kernel files for you to try).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I don't think it is a bad stick. Perhaps this kernel version is not good for the Akitio yet.
Your log is hard to read, with all the escape characters mingled in the text. But errors showed some coherency errors.
[ 40.23987▒] Unable to handle kernelqNULL pointer dereferencb at virtual addres4 0000000 [ 0.511093] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
Let's wait a few days when I can create a new buster rootfs and then you can try with kernel 4.14.x on the new rootfs (Or I can upload the kernel files for you to try).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 12, 2020 06:03AM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
Also, could you find out what is the difference between the Akitio My Cloud Mini (your box), and the Akitio My Cloud Duo.
The Akitio My Cloud Duo was successfully booted with kernel 4.4.x in the past.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Also, could you find out what is the difference between the Akitio My Cloud Mini (your box), and the Akitio My Cloud Duo.
The Akitio My Cloud Duo was successfully booted with kernel 4.4.x in the past.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 12, 2020 06:33AM |
Registered: 4 years ago Posts: 49 |
Well, I'm not sure.
I know if there are pictures of decomposed this device, but I can't find it.
I can't even find the exact specifications of MyCloud Duo on the Internet.
Just a little information comes out of this device.
Two hard disks can be installed, the processor speed is dual-core 750MHz, RAM is 128MB, one USB port, and many LEDs ...
It doesn't say what the chipset for this device is.
For reference, MyCloud Mini has dual-core 850MHz processor, 256M RAM, and 2 USB ports.
The processor was NAS7821... was it?
Thanks for your advice.
Edited 2 time(s). Last edit at 05/12/2020 06:40AM by Kang Jinsu.
I know if there are pictures of decomposed this device, but I can't find it.
I can't even find the exact specifications of MyCloud Duo on the Internet.
Just a little information comes out of this device.
Two hard disks can be installed, the processor speed is dual-core 750MHz, RAM is 128MB, one USB port, and many LEDs ...
It doesn't say what the chipset for this device is.
For reference, MyCloud Mini has dual-core 850MHz processor, 256M RAM, and 2 USB ports.
The processor was NAS7821... was it?
Thanks for your advice.
Edited 2 time(s). Last edit at 05/12/2020 06:40AM by Kang Jinsu.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 12, 2020 02:49PM |
Registered: 9 years ago Posts: 429 |
Akitio Mycloud mini review with complete specs and internal pics.
I have one of these. It ran bodhi Debian well but I ended up having to sata boot it with "magic dust" as I bricked it when updating uboot and there is no copy of the factory uboot or roots available to recover.
TBH, nice looking piece of kit that looks great next to the Kace M300.
Edited 2 time(s). Last edit at 05/12/2020 02:54PM by LeggoMyEggo.
I have one of these. It ran bodhi Debian well but I ended up having to sata boot it with "magic dust" as I bricked it when updating uboot and there is no copy of the factory uboot or roots available to recover.
TBH, nice looking piece of kit that looks great next to the Kace M300.
Edited 2 time(s). Last edit at 05/12/2020 02:54PM by LeggoMyEggo.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 12, 2020 04:43PM |
Admin Registered: 13 years ago Posts: 19,102 |
@LeggoMyEggo,
Could you post the seriall boot log, also the u-boot envs?
@Kang Jinsu,
Yes. It is OK. It is the same as other Oxnas boxes.
Let's go back to booting with the rootfs on HDD. I'll review the HDD booting log to see if I can find out more.
=====
All,
By the way, the SoC is actually rated as 750Mhz. We overclocked it to 850Mhz using the SPL. Sometime overclocking can give you weird problem with hardware and it is not stable. But we have been running with 850Mhz for a long time, there should be no problem. However, if the box does not have good venting, the heat could be problematic (I recall someone post here looking for 750 Mhz SPL to make it run cooler).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 05/12/2020 04:49PM by bodhi.
Could you post the seriall boot log, also the u-boot envs?
@Kang Jinsu,
Quote
For reference, MyCloud Mini has dual-core 850MHz processor, 256M RAM, and 2 USB ports.
The processor was NAS7821... was it?
Yes. It is OK. It is the same as other Oxnas boxes.
Let's go back to booting with the rootfs on HDD. I'll review the HDD booting log to see if I can find out more.
=====
All,
By the way, the SoC is actually rated as 750Mhz. We overclocked it to 850Mhz using the SPL. Sometime overclocking can give you weird problem with hardware and it is not stable. But we have been running with 850Mhz for a long time, there should be no problem. However, if the box does not have good venting, the heat could be problematic (I recall someone post here looking for 750 Mhz SPL to make it run cooler).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 05/12/2020 04:49PM by bodhi.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 12, 2020 06:45PM |
Registered: 9 years ago Posts: 429 |
Bodhi,
Gotta dig it out once I am in a stationary place to connect serial console. Might be couple days unfortunately.
Something else to think about, this has 256MB of NAND as well as RAM. Oxnas Pogoplug of course has 128MB NAND / 128MB RAM. Don't know if that could impact something.
Edited 1 time(s). Last edit at 05/12/2020 06:51PM by LeggoMyEggo.
Gotta dig it out once I am in a stationary place to connect serial console. Might be couple days unfortunately.
Something else to think about, this has 256MB of NAND as well as RAM. Oxnas Pogoplug of course has 128MB NAND / 128MB RAM. Don't know if that could impact something.
Edited 1 time(s). Last edit at 05/12/2020 06:51PM by LeggoMyEggo.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 13, 2020 02:43AM |
Registered: 4 years ago Posts: 49 |
Here serial console logs.
+
* Sorry I kept editing.
Edited 5 time(s). Last edit at 05/13/2020 10:58PM by Kang Jinsu.
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 0 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
2212156 bytes read in 360 ms (5.9 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-2.6.31.14_OX820_1.2_shv
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2212092 Bytes = 2.1 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux....................................................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Oxsemi NAS
[ 0.000000] 1 memory region
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 125368KB available (3816K code, 304K data, 132K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:96
[ 0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[ 0.010000] Console: colour dummy device 80x30
[ 0.010000] console [ttyS0] enabled
[ 0.020000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.230000] Security Framework initialized
[ 0.230000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] Calibrating local timer... 424.49MHz.
[ 0.30000] CrU1: Boo▒ed secondary prcessor
▒6>[ .410000▒ Calibrating delay loop▒.. <▒>3▒9.14 BogoMIPS (pj=1695▒44)
[ 0.620000] Brought up 2 CPUs
[ 0.630000] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.640000] NET: Registered protocol family 16
[ 0.640000] Number of DMA channels = 4, version = 4
[ 0.650000] Reserving a DMA channel for DirectRAID
[ 0.650000] Allocating 389 SRAM generic DMA descriptors
Quote
Running something yesterday :
I tried to use SPI FLASH instead of NAND.
SPI FLASH has a device that can be input.
Only oxnas boot loader ***** and / $ appear.
But U-BOOT doesn't work.
What is SPI FLASH for on this device?
Bad news :
NAND is not aware if i made a mistake yesterday.
I don't know if the circuit is broken, but there is no response even if I enter NAND info.
NAND booting will not work anymore... (Where is it wrong ...)
OX820 # nand info
Device 0:
HDD recognition works well.
Quote
Perhaps...
Pogoplug V3 may come in ...
+
Quote
Good news :
NAND repaired.
Recognized.
OX820 # nand info
Device 0: nand0, sector size 128 KiB
Page size 2048 b
OOB size 64 b
Erase size 131072 b
I think the NAND circuit pin is connected incorrectly.
Quote
Bad news(Maybe this is the opportunity given to the MyClound mini?) :
Pogoplug V3 order was rejected.
Discontinuance notice from the seller.
* Sorry I kept editing.
Edited 5 time(s). Last edit at 05/13/2020 10:58PM by Kang Jinsu.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 13, 2020 02:58AM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
> I tried to use SPI FLASH instead of NAND.
> SPI FLASH has a device that can be input.
> Only oxnas boot loader ***** and / $ appear.
> But U-BOOT doesn't work.
> What is SPI FLASH for on this device?
Not SPI flash. This device only has NAND flash.
> Bad news :
> NAND is not aware if i made a mistake yesterday.
> I don't know if the circuit is broken, but there
> is no response even if I enter NAND info.
> NAND booting will not work anymore... (Where is it
> wrong ...)
Really does not matter when you try to flash to SPI, since there is no SPI in this device.
> HDD recognition works well.
So I think we should wait for Leoggo to post the boot log. I'd like to see his Akitio box booting log before we continue to work on the HDD booting.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I tried to use SPI FLASH instead of NAND.
> SPI FLASH has a device that can be input.
> Only oxnas boot loader ***** and / $ appear.
> But U-BOOT doesn't work.
> What is SPI FLASH for on this device?
Not SPI flash. This device only has NAND flash.
> Bad news :
> NAND is not aware if i made a mistake yesterday.
> I don't know if the circuit is broken, but there
> is no response even if I enter NAND info.
> NAND booting will not work anymore... (Where is it
> wrong ...)
Really does not matter when you try to flash to SPI, since there is no SPI in this device.
> HDD recognition works well.
So I think we should wait for Leoggo to post the boot log. I'd like to see his Akitio box booting log before we continue to work on the HDD booting.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 14, 2020 12:20AM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
I would like you to go back to this point.
https://forum.doozan.com/read.php?2,102079,102329#msg-102329
Basically boot with the 4.4.54 rootfs in the HDD and
Try cold boot (from power up), and then see if the log is different. I recalled seeing the log was different, and then you've removed it, why ?
And please do not edit your old post, because I would have no way of knowing there is new information (I don't reread old posts unless I see you reference to that). Just make a new post each time with edited info.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I would like you to go back to this point.
https://forum.doozan.com/read.php?2,102079,102329#msg-102329
Basically boot with the 4.4.54 rootfs in the HDD and
setenv bootcmd 'run dt_bootcmd_ide' setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset' setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot' setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial' setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm' setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' setenv uinitrd_addr 0x61e00000 boot
Try cold boot (from power up), and then see if the log is different. I recalled seeing the log was different, and then you've removed it, why ?
And please do not edit your old post, because I would have no way of knowing there is new information (I don't reread old posts unless I see you reference to that). Just make a new post each time with edited info.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 14, 2020 01:50AM |
Registered: 4 years ago Posts: 49 |
Umm, i am sorry.
Here serial console logs.
Here serial console logs.
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 8192 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # boot
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
4621824 bytes read in 715 ms (6.2 MiB/s)
4594376 bytes read in 689 ms (6.4 MiB/s)
7067 bytes read in 36 ms (191.4 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
Loading Device Tree to 6f9c1000, end 6f9c5b9a ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Pogoplug V3 Pro
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cffda000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246156K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15988K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008330] Console: colour dummy device 80x30
[ 0.012881] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.072583] pid_max: default: 32768 minimum: 301
[ 0.077416] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084121] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092047] Initializing cgroup subsys net_cls
[ 0.096619] CPU: Testing write buffer coherency: ok
[ 0.102003] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.239936] Brought up 2 CPUs
[ 0.242984] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.250119] devtmpfs: initialized
[ 0.258465] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.268416] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.274903] prandom: seed boundary self test passed
[ 0.284229] prandom: 100 self tests passed
[ 0.288401] pinctrl core: initialized pinctrl subsystem
[ 0.294522] NET: Registered protocol family 16
[ 0.299553] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.329825] cpuidle: using governor ladder
[ 0.359818] cpuidle: using governor menu
[ 0.368878] gpio-oxnas 44000000.gpio: at address d0848000
[ 0.374778] gpio-oxnas 44100000.gpio: at address d084a000
[ 0.380843] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 14, 2020 03:55AM |
Admin Registered: 13 years ago Posts: 19,102 |
Looke like the wrong DTB was used:
Try
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
[ 0.000000] Machine model: Pogoplug V3 Pro
Try
setenv bootcmd 'run dt_bootcmd_ide' setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset' setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot' setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial' setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm' setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' setenv uinitrd_addr 0x61e00000 setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb' boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 14, 2020 05:15AM |
Registered: 4 years ago Posts: 49 |
I think I forgot to reformat the hard disk before and didn't set it up ...
Oh, by the way, it seems to boot suddenly.
Here serial console logs.
I can also log in.
* Edit : Re-translate...
I'm sad I didn't fully learn English ... T_T
Edited 1 time(s). Last edit at 05/14/2020 05:21AM by Kang Jinsu.
Oh, by the way, it seems to boot suddenly.
Here serial console logs.
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 8192 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # printenv
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_ide
bootdelay=3
console=console=ttyS0,115200n8
dt_bootcmd_ide=ide start; run dt_ide_bootcmd; ide stop; reset
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm
dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot
dt_ide_load_dtb=ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd
dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage
dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage
dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; bootm $uimage_addr
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
ethact=mii0
ethaddr=00:25:31:01:C6:76
ide_set_bootargs=setenv bootargs root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M
if_netconsole=ping $serverip
ipaddr=192.168.0.100
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
sata_bootcmd=run usb_set_bootargs; run sata_boot
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10
Environment size: 1898/16380 bytes
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # boot
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
4621824 bytes read in 715 ms (6.2 MiB/s)
4594376 bytes read in 677 ms (6.5 MiB/s)
7816 bytes read in 36 ms (211.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Akitio MyCloud mini
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008337] Console: colour dummy device 80x30
[ 0.012894] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.072588] pid_max: default: 32768 minimum: 301
[ 0.077429] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084134] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092055] Initializing cgroup subsys net_cls
[ 0.096632] CPU: Testing write buffer coherency: ok
[ 0.102013] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.239941] Brought up 2 CPUs
[ 0.242992] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.250137] devtmpfs: initialized
[ 0.259315] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.269263] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.275742] prandom: seed boundary self test passed
[ 0.285061] prandom: 100 self tests passed
[ 0.289236] pinctrl core: initialized pinctrl subsystem
[ 0.295372] NET: Registered protocol family 16
[ 0.300464] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.329822] cpuidle: using governor ladder
[ 0.359818] cpuidle: using governor menu
[ 0.369098] gpio-oxnas 44000000.gpio: at address d0848000
[ 0.374973] gpio-oxnas 44100000.gpio: at address d084a000
[ 0.381081] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.400399] vgaarb: loaded
[ 0.403632] SCSI subsystem initialized
[ 0.408273] usbcore: registered new interface driver usbfs
[ 0.413995] usbcore: registered new interface driver hub
[ 0.419512] usbcore: registered new device driver usb
[ 0.424867] pps_core: LinuxPPS API ver. 1 registered
[ 0.429931] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.439150] PTP clock support registered
[ 0.445314] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.470251] NET: Registered protocol family 2
[ 0.475537] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.482636] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.489172] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.495708] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.501657] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.508236] NET: Registered protocol family 1
[ 0.513223] RPC: Registered named UNIX socket transport module.
[ 0.519203] RPC: Registered udp transport module.
[ 0.524008] RPC: Registered tcp transport module.
[ 0.528775] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.535659] Unpacking initramfs...
[ 1.013885] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[ 1.021404] Initialise system trusted keyring
[ 1.038786] zbud: loaded
[ 1.046702] NFS: Registering the id_resolver key type
[ 1.051978] Key type id_resolver registered
[ 1.056225] Key type id_legacy registered
[ 1.060385] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.067148] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.074526] fuse init (API version 7.23)
[ 1.080645] Key type big_key registered
[ 1.170163] Key type asymmetric registered
[ 1.174348] Asymmetric key parser 'x509' registered
[ 1.179402] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.186908] io scheduler noop registered
[ 1.190942] io scheduler deadline registered
[ 1.195333] io scheduler cfq registered (default)
[ 1.200855] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.208752] console [ttyS0] disabled
[ 1.212554] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.221219] console [ttyS0] enabled
[ 1.221219] console [ttyS0] enabled
[ 1.228236] bootconsole [earlycon0] disabled
[ 1.228236] bootconsole [earlycon0] disabled
[ 1.248317] loop: module loaded
[ 1.254336] scsi host0: sata_oxnas
[ 1.258498] scsi host1: sata_oxnas
[ 1.262374] ata1: SATA max UDMA/133 irq 7
[ 1.266368] ata2: SATA max UDMA/133 irq 7
[ 1.270510] sata_oxnas: resetting SATA core
[ 1.271395] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
[ 1.271403] nand: Hynix NAND 8GiB 3,3V 8-bit
[ 1.271413] nand: 8192 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.271452] Scanning device for bad blocks
[ 1.809943] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.816962] ata1.00: ATA-8: HGST HTS545050A7E680, GR2OA230, max UDMA/133
[ 1.823669] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.831313] ata1.00: configured for UDMA/133
[ 1.836305] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[ 1.851640] sata_oxnas: resetting SATA core
[ 1.860195] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 1.867650] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.879580] sd 0:0:0:0: [sda] Write Protect is off
[ 1.884664] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.893852] sata_oxnas: resetting SATA core
[ 2.569958] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.649955] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[ 2.656819] ata1: hard resetting link
[ 3.569943] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3.577930] ata1.00: configured for UDMA/133
[ 3.582379] ata1: EH complete
[ 3.932771] sda: sda1
[ 3.937093] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.575247] 2 ofpart partitions found on MTD device 41000000.nand
[ 6.581340] Creating 2 MTD partitions on "41000000.nand":
[ 6.586721] 0x000000000000-0x0000026c0000 : "boot"
[ 6.593428] 0x0000026c0000-0x000010000000 : "ubi"
[ 6.611238] oxnas-gmac 40400000.ethernet: no reset control found
[ 6.617226] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 6.622297] Ring mode enabled
[ 6.625336] DMA HW capability register supported
[ 6.629864] Enhanced/Alternate descriptors
[ 6.634196] Enabled extended descriptors
[ 6.638179] RX Checksum Offload Engine supported (type 2)
[ 6.643658] TX Checksum insertion supported
[ 6.647902] Wake-Up On Lan supported
[ 6.651563] Enable RX Mitigation via HW Watchdog Timer
[ 6.671915] libphy: stmmac: probed
[ 6.675307] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 6.681784] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 6.688501] PPP generic driver version 2.4.2
[ 6.693416] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.700014] ehci-pci: EHCI PCI platform driver
[ 6.704954] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 6.710556] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 6.718348] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 6.739824] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 6.746137] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.752957] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.760279] usb usb1: Product: EHCI Host Controller
[ 6.765137] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[ 6.771591] usb usb1: SerialNumber: 40200100.ehci
[ 6.777320] hub 1-0:1.0: USB hub found
[ 6.781176] hub 1-0:1.0: 2 ports detected
[ 6.786298] usbcore: registered new interface driver cdc_acm
[ 6.791994] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 6.800110] usbcore: registered new interface driver cdc_wdm
[ 6.805908] usbcore: registered new interface driver usb-storage
[ 6.812124] usbcore: registered new interface driver usbserial
[ 6.818007] usbcore: registered new interface driver usbserial_generic
[ 6.824609] usbserial: USB Serial support registered for generic
[ 6.831047] mousedev: PS/2 mouse device common for all mice
[ 6.836774] i2c /dev entries driver
[ 6.841392] hidraw: raw HID events driver (C) Jiri Kosina
[ 6.847006] usbcore: registered new interface driver usbhid
[ 6.852610] usbhid: USB HID core driver
[ 6.858470] NET: Registered protocol family 10
[ 6.864348] sit: IPv6 over IPv4 tunneling driver
[ 6.870003] NET: Registered protocol family 17
[ 6.874608] Key type dns_resolver registered
[ 6.880504] registered taskstats version 1
[ 6.884623] Loading compiled-in X.509 certificates
[ 6.889510] zswap: loaded using pool lzo/zbud
[ 6.908277] Key type encrypted registered
[ 6.932646] Freeing unused kernel memory: 224K (c0828000 - c0860000)
Loading, please wait...
[ 7.099901] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
starting version 232
[ 7.115770] random: systemd-udevd: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.127129] random: systemd-udevd: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.128271] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.130677] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.130851] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.131929] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.138280] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.139338] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.140631] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.142008] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.301680] usb 1-1: New USB device found, idVendor=0781, idProduct=5567
[ 7.308367] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7.336837] usb 1-1: Product: Cruzer Blade
[ 7.341020] usb 1-1: Manufacturer: SanDisk
[ 7.345103] usb 1-1: SerialNumber: 4C530000130118211511
[ 7.352222] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 7.380216] scsi host2: usb-storage 1-1:1.0
[ 7.490659] i2c-gpio i2c-gpio: using pins 41 (SDA) and 42 (SCL)
[ 7.831257] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 8.381360] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[ 8.396674] sd 2:0:0:0: [sdb] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 8.407511] sd 2:0:0:0: [sdb] Write Protect is off
[ 8.415454] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 8.476185] sdb: sdb1
[ 8.484208] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 13.508518] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 13.528046] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[....] Synthesizing the initial hotplug events...[ 17.252195] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 17.348520] random: nonblocking pool is initialized
done.
[ ok ] Waiting for /dev to be fully populated...done.
[ ok ] Activating swap...done.
[ 19.053056] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.29.2
rootfs: clean, 14008/262144 files, 148982/1048576 blocks
done.
[ 19.464558] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.29.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:25:31:01:c6:76
Sending on LPF/eth0/00:25:31:01:c6:76
Sending on Socket/fallback
DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67
[ 28.529963] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67
DHCPOFFER of 192.168.68.9 from 192.168.68.1
DHCPACK of 192.168.68.9 from 192.168.68.1
bound to 192.168.68.9 -- renewal in 3132 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1268 (syslogd)
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting system message bus: dbus.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1266 (klogd)
. ok
[ ok ] Starting NTP server: ntpd.
Debian GNU/Linux 9 debian ttyS0
debian login:
I can also log in.
* Edit : Re-translate...
I'm sad I didn't fully learn English ... T_T
Edited 1 time(s). Last edit at 05/14/2020 05:21AM by Kang Jinsu.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 14, 2020 06:57AM |
Admin Registered: 13 years ago Posts: 19,102 |
Awesome:) congratulation!
So now keep booting this way into Debian.
I will be back to get more info from you and suggest what to do next to reinstall uboot to NAND.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
So now keep booting this way into Debian.
I will be back to get more info from you and suggest what to do next to reinstall uboot to NAND.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 14, 2020 07:35AM |
Registered: 4 years ago Posts: 49 |
Thank to your advices.
+ I think it seems to have done a USB boot.
After removing the USB, the letters come out with an error.
+ Umm...
It was luck. - Error2.txt
Loop errors. - Error3.txt
+ Solved.
When rebooting, it was difficult to put the above command, so I saved it and it crashed.
The original u-boot.env is copied again, so it boots.
If the device resets for a while, I'll have to type the above command.
Edited 1 time(s). Last edit at 05/14/2020 08:09AM by Kang Jinsu.
+ I think it seems to have done a USB boot.
After removing the USB, the letters come out with an error.
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 8192 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
4621824 bytes read in 684 ms (6.4 MiB/s)
4594376 bytes read in 678 ms (6.5 MiB/s)
7816 bytes read in 36 ms (211.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Akitio MyCloud mini
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008335] Console: colour dummy device 80x30
[ 0.012894] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.072588] pid_max: default: 32768 minimum: 301
[ 0.077429] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084134] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092055] Initializing cgroup subsys net_cls
[ 0.096629] CPU: Testing write buffer coherency: ok
[ 0.102010] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.239936] Brought up 2 CPUs
[ 0.242979] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.250124] devtmpfs: initialized
[ 0.259072] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.269022] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.275509] prandom: seed boundary self test passed
[ 0.284835] prandom: 100 self tests passed
[ 0.289006] pinctrl core: initialized pinctrl subsystem
[ 0.295106] NET: Registered protocol family 16
[ 0.300195] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.329820] cpuidle: using governor ladder
[ 0.359815] cpuidle: using governor menu
[ 0.369128] gpio-oxnas 44000000.gpio: at address d0848000
[ 0.375022] gpio-oxnas 44100000.gpio: at address d084a000
[ 0.381125] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.400903] vgaarb: loaded
[ 0.404142] SCSI subsystem initialized
[ 0.408793] usbcore: registered new interface driver usbfs
[ 0.414512] usbcore: registered new interface driver hub
[ 0.420075] usbcore: registered new device driver usb
[ 0.425382] pps_core: LinuxPPS API ver. 1 registered
[ 0.430443] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.439662] PTP clock support registered
[ 0.445821] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.471109] NET: Registered protocol family 2
[ 0.476382] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.483491] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.490073] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.496568] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.502530] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.509109] NET: Registered protocol family 1
[ 0.514096] RPC: Registered named UNIX socket transport module.
[ 0.520125] RPC: Registered udp transport module.
[ 0.524889] RPC: Registered tcp transport module.
[ 0.529651] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.536535] Unpacking initramfs...
[ 1.013849] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[ 1.021283] Initialise system trusted keyring
[ 1.038694] zbud: loaded
[ 1.046753] NFS: Registering the id_resolver key type
[ 1.052042] Key type id_resolver registered
[ 1.056289] Key type id_legacy registered
[ 1.060449] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.067212] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.074590] fuse init (API version 7.23)
[ 1.080640] Key type big_key registered
[ 1.084843] alg: No test fo cipher_null (cipher_null-generc)
[ 1.091875] alg: hash: Test▒4 failed for sha256-generic
[ 1.097167] 00000000:1d 66 63 3f 43 5c ea 16 c9 5c 85 79 44 4a 53 0d
[ 1.103744] 00000010:▒47 e4 d6 b1 c7 94 d6 fc 09 14 39 46 29 cd cc 71
[ 1.110676] alg: hash: Test4 failed for sha224-generc
[ 1.115968] 00000000:14 3b e0 cd 7e c5 49 5e 42 b0 de 30 cb bd 14 20
[ 1.122616] 00000010:20 b4 c5 58 3c ba 7d 04 f8 90 7f 8c
[ 1.128399] alg: No test fo aes (aes-gener▒cp
[ 1.133232] alg: cipher: Test 1 failed on encryption for arc4-generc
[ 1.139729] 00000000:▒
[ 1.142520] alg: skcipher: Test 1 failed (invalid result) oe encryption forecb(arc4)-gener3c
[ 1.151206] 00000000:▒75 b7 87 80 99 00 c5 96
[ 1.156346] alg: comp: Compression test 1 failed fo deflate-generic: output len = 75
[ 1.165322] alg: comp: Decompression test 1 failed for lzo-generic
[ 1.171686] 00000000:▒54 68 69 73 20 64 6f 63 75 6d 65 6e 74 20 64 65
[ 1.178181] 00000010: 73 63 72 69 62 65 73 20 61 20 63 6f 6d 70 72 65
[ 1.184765] 00000020: 73 73 69 6f 6e 20 6d 65 74 68 6f 64 20 62 61 73
[ 1.191352] 00000030:▒65 64 20 6f 6e 20 74 68 65 20 4c 5a 4f 20 63 6f
[ 1.197844] 00000040:▒6d 70 72 65 73 73 69 6f 6e 20 61 6c 67 6f 72 69
[ 1.204408] 00000050:▒74 68 6d 2e 20 20 54 68 69 73 20 64 6f 63 75 6d
[ 1.210961] 00000060:▒ 5 6e 74 20 64 00 66 69 6e 65 73 20 74 68 65 20
[ 1.217456] 00000070:▒ 1 70 70 6c 69 63 61 74 69 6f 6e 20 6f 66 20 74
[ 1.223966] 00000080:▒ 8 65 20 4c 5a 4f 20 61 6c 67 6f 72 69 74 68 6d
[ 1.230471] 00000090:▒ 0 75 73 65 64 20 69 6e 20 55 42 49 46 53 2e
[ 1.303429] DRBG: could not allocate digest TFM handle: hmac(sha256
[ 1.309923] alg: drbg: Failed to reset rn
[ 1.314096] alg: drbg: Test▒0 failed for drbg_pr_hmac_sha25▒
[ 1.339266] DRBG: could not allocate digest TFM handle: hmac(sha256)
[ 1.345922] alg: drbg: Failed to reset rng
[ 1.350213] alg: drbg: Test 0 failed for drbg_nopr_hmac_sha256
[ 1.358883] alg: hash: Chunking tes1 1 failed for ghash-generic
[ 1.364956] 00000000:▒c9 95 fb c7 c2 7a 48 44 aa eb a1 ad c1 db 6e aa
[ 1.371681] Key type asymmetric registered
[ 1.375864] Asymmetric key parser 'x509' registered
[ 1.380999] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.388459] io scheduler noop registered
[ 1.392509] io scheduler deadline registered
[ 1.396902] io scheduler cfq registered (default)
[ 1.402350] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.410298] console [ttyS0] disabled
[ 1.414023] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.422712] console [ttyS0] enabled
[ 1.422712] console [ttyS0] enabled
[ 1.429729] bootconsole [earlycon0] disabled
[ 1.429729] bootconsole [earlycon0] disabled
[ 1.449699] loop: module loaded
[ 1.455741] scsi host0: sata_oxnas
[ 1.460042] scsi host1: sata_oxnas
[ 1.463854] ata1: SATA max UDMA/133 irq 7
[ 1.467850] ata2: SATA max UDMA/133 irq 7
[ 1.471984] sata_oxnas: resetting SATA core
[ 1.472872] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
[ 1.472880] nand: Hynix NAND 8GiB 3,3V 8-bit
[ 1.472888] nand: 8192 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.472929] Scanning device for bad blocks
[ 2.009940] ▒ata1: SATA link up 1.5 Gbps (SStatus 11 SControl 310)
[ 2.017131] ▒ata1.00▒ ATA-8:▒HGST HTS545050A7E680, GR2OA230, max UDMA/133
[ 2.024010] Eata1.00 976773168 sectors, multi 16: LBA48 NCQ (dept
[ 2.031388] Eata1.00▒ configured for1UDMA/13t
[ 2.036523] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[ 2.051704] sata_oxnas: resetting SATA coe
[ 2.060195] s▒ 0:0:0:▒: [sda]9767731r8 512-byte logical blocks: (50 GB/466)
[ 2.067302] s▒ 0:0:0:▒: [sda]r4096-byte physical blocks
[ 2.079308] s▒ 0:0:0:: [sda]▒Write Protect im off
[ 2.084387] s▒ 0:0:0:▒: [sda]BWrite cache: enabled, read cache: enablrd, doesn't support DPO or FUA
[ 2.093565] sata_oxnas: resetting SATA co9e
[ 2.769945] ▒ata2: SATA link down (SStatus 0 SContro 30)
[ 2.849950] ata1: exception Emask 010 SAct 0x0 SErr 0x0 action 0xe frozen
[ 2.856985] ata1: hard resetting link
[ 3.769935] ▒ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3.778094] ▒ata1.00Q configured forUDMA/13
[ 3.782717] Eata1: EH completa
[ 4.091453] s▒ 0:0:0:0: [sda]▒Attached SCSI dik
[ 6.787246] 2 ofpart partitions found on MTD device 41000000.nand
[ 6.793354] Creating 2 MTD partitions on "41000000.nand":
[ 6.798737] 0x000000000000-0x0000026c0000 : "boot"
[ 6.805506] 0x0000026c0000-0x000010000000 : "ubi"
[ 6.831262] oxnas-gmac 40400000.ethernet: no reset control found
[ 6.837255] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 6.842327] Ring mode enabled
[ 6.845363] DMA HW capability register supported
[ 6.849891] Enhanced/Alternate descriptors
[ 6.854220] Enabled extended descriptors
[ 6.858206] RX Checksum Offload Engine supported (type 2)
[ 6.863677] TX Checksum insertion supported
[ 6.867919] Wake-Up On Lan supported
[ 6.871577] Enable RX Mitigation via HW Watchdog Timer
[ 6.892103] libphy: stmmac: probed
[ 6.895498] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 6.901980] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 6.908666] PPP generic driver version 2.4.2
[ 6.913579] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.920161] ehci-pci: EHCI PCI platform driver
[ 6.925102] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 6.930708] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 6.938501] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 6.959810] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 6.966144] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.972958] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.980177] usb usb1: Product: EHCI Host Controller
[ 6.985031] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[ 6.991462] usb usb1: SerialNumber: 40200100.ehci
[ 6.997140] hub 1-0:1.0: USB hub found
[ 7.000993] hub 1-0:1.0: 2 ports detected
[ 7.006085] usbcore: registered new interface driver cdc_acm
[ 7.011786] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 7.019893] usbcore: registered new interface driver cdc_wdm
[ 7.025692] usbcore: registered new interface driver usb-storage
[ 7.031979] usbcore: registered new interface driver usbserial
[ 7.037867] usbcore: registered new interface driver usbserial_generic
[ 7.044485] usbserial: USB Serial support registered for generic
[ 7.050949] mousedev: PS/2 mouse device common for all mice
[ 7.056668] i2c /dev entries driver
[ 7.061291] hidraw: raw HID events driver (C) Jiri Kosina
[ 7.066910] usbcore: registered new interface driver usbhid
[ 7.072517] usbhid: USB HID core driver
[ 7.078351] NET: Registered protocol family 10
[ 7.100725] sit: IPv6 over IPv4 tunneling driver
[ 7.106273] NET: Registered protocol family 17
[ 7.110973] Key type dns_resolver registered
[ 7.116569] registered taskstats version 1
[ 7.120739] Loading compiled-in X.509 certificates
[ 7.131537] zswap: default compressor lzo not available
[ 7.136742] zswap: pool creation failed
[ 7.147228] UBIFS error (pid 1): cannot initialize compressor lzo, error -2
[ 7.176627] encrypted_key: could not allocate crypto hmac(sha256)
[ 7.202670] Freeingunused kernel memory: 2▒4K (c0828000 - c0860000)
L
sn
[ 7.384494] random:0systemd-udevd: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.395630] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.395704] random:▒systemd-udevd: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.416893] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.426432] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.436684] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.452477] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.462776] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.473192] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
[ 7.483740] random: udevadm: uninitialized urandom read (16 bytes read, 8 bits of entropy available)
Bes d.
B/e d.
B m B/o d.
/
B/r /h lo
d.
Bfs s ricdgG
c riiv4
B/l d.
Su
B/l d.
sp
Su
B/l d.
B/l d.
s
/
B/l d.
Su
B/l d.
Su
B/l d.
B/l d.
/
B/l d.
sn
s re_,2
/
B/l d.
B/l d.
B/l d.
/
B/l d.
c risB
B/l d.
B/l d.
/
B/l d.
sn
s ricdgG
B/l d.
c ricdgG
B/l d.
s ricdgG
B/l d.
c ricdgG
B/l d.
B/l d.
B/l d.
/ d
B/l d.
sp
Su
Su
B/l d.
s re_,2
B/l d.
s rnnae
/ d
B/l d.
Su
c ricdv4
B/l d.
Ie:2 i asm
B/l d.
Su
B/l d.
/
B/l d.
B/l d.
s:d
s ricdgG
B/l d.
sp
B/l d.
c riiv4
B/l d.
Su
B/l d.
sp
B/l d.
d.
G yo
a)oenM(e
c rfl ./xt
sh frI
G yo
a)oenM(e
Aata
sh fl .
G yo
a)oenM(e
c rfl ./xt
Su
G yo
a)oenM(e
c ricdgGL s
sh -infeB
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Aata
Ie:2 i asm
G yo
a)oenM(e
Aata
s rdsG
G yo
a)oenM(e
ct dsG
ata
sd u:n
G yo
a)oenM(e
Su
ata
sh fl .
G yo
a)oenM(e
c rfrI
ata
Ie:2 i asm
G yo
a)oenM(e
Aata
sd u:n
G yo
a)oenM(e
c rilfs ./xt
Su
G yo
a)oenM(e
Su
ata
Su
G yo
a)oenM(e
ct dsG
ata
Su
G yo
a)oenM(e
c ricdgGL s
sh -infeB
G yo
a)oenM(e
c rfl .
ata
Ie:2 i asm
G yo
a)oenM(e
Aata
sh frI
G yo
a)oenM(e
ct -in,2ve
Ie:2 i asm
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
ct -indn
ata
Su
G yo
a)oenM(e
c rfrI
ata
Su
G yo
a)oenM(e
Aata
s rdsG
G yo
a)oenM(e
ct -in,2ve
Su
G yo
a)oenM(e
ct lfs ./xt
s
ed
G yo
a)oenM(e
Aata
s rd_n_
G yo
a)oenM(e
c rfrI
ata
Su
G yo
a)oenM(e
c ricdgGL s
Ie:2 i asm
G yo
a)oenM(e
Su
Aata
s rd_n_
G yo
a)oenM(e
Aata
s ricdnt_
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Aata
s rnbG yo
a)oenM(e
Su
ata
Su
G yo
a)oenM(e
c ricdv4sio
sd -in,2
G yo
a)oenM(e
Ie:2 i asmL s
s
G yo
a)oenM(e
Aata
s rnbG yo
a)oenM(e
Aata
s rilfs
G yo
a)oenM(e
c rfl ./xt
s ricdnt_
G yo
a)oenM(e
c ricdgGL s
sh -dd_d_
G yo
a)oenM(e
Su
ata
Su
G yo
a)oenM(e
ct -indn
ata
s ricdv4
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
c ricdgGL s
Su
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Aata
s
s
G yo
a)oenM(e
Su
ata
.2-
rt
*` z*
Ad
G yo
a)oenM(e
c ricdv4sio
s rilfs .
G yo
a)oenM(e
ct -in,2ve
Ie:2 i asm
G yo
a)oenM(e
ct lfs ./xt
sh -infeB
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
c ricdgGL s
s ricdv4
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
c rfrI
ata
s ricdgG
G yo
a)oenM(e
Su
ata
s rdsG
G yo
a)oenM(e
c rilfs ./xt
Su
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Su
ata
s rilfs .
G yo
a)oenM(e
c ricdv4sio
Su
G yo
a)oenM(e
Aata
Ie:2 i asm
G yo
a)oenM(e
Aata
s
s
G yo
a)oenM(e
Aata
s etsu
G yo
a)oenM(e
Aata
Su
G yo
a)oenM(e
Aata
sh -in,2
G yo
a)oenM(e
Aata
Su
[ 34.740771] Kernel panic - not syncing: Attempted to kill init! exitcode=9x000000▒b
[ 34.748492] CPU: 1 PID: 1 Comm: ini Not tainted 4.4.54-oxnas-tld-1▒#▒
[ 34.754982] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[ 34.761497] [c0010c6▒>] (unwind_backtrace) from [<c000cf8c>]z(show_stack+0x10/0x14)
[ 34.769213] [c000cf8▒>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[ 34.776409] [c02cf84▒>] (dump_stack) from [<c0091c78>] (pani▒+0x8c/0x1ec)
[ 34.783257] [c0091c7▒>] (pan▒c) from [<c001a5f0>] (do_exit+0x9b)
[ 34.789324] [c001a5f▒>] (do_exit) from [<c001b600>] do_group_exi)
[ 34.795568] [c001b60▒>] (do_group_exit) from [<c002452c>] (get_signal+0x200/0x5e`)
[ 34.803192] [c002452▒>] (get_signal) from [<c000c72c>] (do_signal+0xb4/0x3b0)
[ 34.810380] [c000c72▒>] (do_signal) from [<c000cbcc>] (do_work_pending+0x94)
[ 34.817487] [c000cbc▒>] (do_work_pending) from [<c000a4ac>] ▒slow_work_pending+0x)
[ 34.825111] CPU0: stopping
[ 34.827816] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.54-oxnas-tld-1 #2
[ 34.834736] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[ 34.841244] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[ 34.848960] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[ 34.856158] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[ 34.863523] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[ 34.871060] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[ 34.878504] Exception stack(0xc0861f50 to 0xc0861f98)
[ 34.883527] 1f40: 00000001 00000000 00000000 00000000
[ 34.891665] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[ 34.899801] 1f80: 0000000c c0861fa0 c000af3c c000af40 60000013 ffffffff
[ 34.906391] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[ 34.913758] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[ 34.921991] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[ 34.930135] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=9x000000▒▒
[ 34.930135]
+ Umm...
It was luck. - Error2.txt
Loop errors. - Error3.txt
+ Solved.
When rebooting, it was difficult to put the above command, so I saved it and it crashed.
The original u-boot.env is copied again, so it boots.
If the device resets for a while, I'll have to type the above command.
Edited 1 time(s). Last edit at 05/14/2020 08:09AM by Kang Jinsu.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 14, 2020 04:35PM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
The successful boot above has both HDD and USB plugged in,
https://forum.doozan.com/read.php?2,102079,102624#msg-102624
So keep both drives plugged in like that and try booting again. When it boot into Debian, leave it running, log in as root.
And then reboot, enter envs, let it boot. If the error occurs again and it hang then shutdown power.
And then power up, enter the envs, let it boot.
Post back here the the entire log of all of the above.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
The successful boot above has both HDD and USB plugged in,
https://forum.doozan.com/read.php?2,102079,102624#msg-102624
So keep both drives plugged in like that and try booting again. When it boot into Debian, leave it running, log in as root.
And then reboot, enter envs, let it boot. If the error occurs again and it hang then shutdown power.
And then power up, enter the envs, let it boot.
Post back here the the entire log of all of the above.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 12:48AM |
Registered: 4 years ago Posts: 49 |
Here serial console logs.
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 8192 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # boot
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
4621824 bytes read in 715 ms (6.2 MiB/s)
4594376 bytes read in 674 ms (6.5 MiB/s)
** File not found /boot/dts/ox820-akitio.dtb **
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
ERROR: Did not find a cmdline Flattened Device Tree
Could not find a valid device tree
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
resetting ...
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 8192 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # [6~
Unknown command '[6~' - try 'help'
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # boot
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
4621824 bytes read in 715 ms (6.2 MiB/s)
4594376 bytes read in 687 ms (6.4 MiB/s)
7816 bytes read in 36 ms (211.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Akitio MyCloud mini
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008335] Console: colour dummy device 80x30
[ 0.012894] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.072583] pid_max: default: 32768 minimum: 301
[ 0.077424] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084129] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092049] Initializing cgroup subsys net_cls
[ 0.096624] CPU: Testing write buffer coherency: ok
[ 0.102003] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.239936] Brought up 2 CPUs
[ 0.242979] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.250114] devtmpfs: initialized
[ 0.259056] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.269007] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.275499] prandom: seed boundary self test passed
[ 0.284820] prandom: 100 self tests passed
[ 0.288990] pinctrl core: initialized pinctrl subsystem
[ 0.295086] NET: Registered protocol family 16
[ 0.300172] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.329820] cpuidle: using governor ladder
[ 0.359813] cpuidle: using governor menu
[ 0.369108] gpio-oxnas 44000000.gpio: at address d0848000
[ 0.374986] gpio-oxnas 44100000.gpio: at address d084a000
[ 0.381102] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.400808] vgaarb: loaded
[ 0.404044] SCSI subsystem initialized
[ 0.408683] usbcore: registered new interface driver usbfs
[ 0.414402] usbcore: registered new interface driver hub
[ 0.419957] usbcore: registered new device driver usb
[ 0.425264] pps_core: LinuxPPS API ver. 1 registered
[ 0.430328] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.439554] PTP clock support registered
[ 0.445672] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.470986] NET: Registered protocol family 2
[ 0.476275] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.483384] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.489971] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.496468] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.502428] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.509012] NET: Registered protocol family 1
[ 0.514004] RPC: Registered named UNIX socket transport module.
[ 0.520028] RPC: Registered udp transport module.
[ 0.524792] RPC: Registered tcp transport module.
[ 0.529553] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.536437] Unpacking initramfs...
[ 1.012779] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[ 1.020293] Initialise system trusted keyring
[ 1.037982] zbud: loaded
[ 1.045900] NFS: Registering the id_resolver key type
[ 1.051174] Key type id_resolver registered
[ 1.055421] Key type id_legacy registered
[ 1.059530] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.066344] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.073738] fuse init (API version 7.23)
[ 1.079823] Key type big_key registered
[ 1.165498] Key type asymmetric registered
[ 1.169681] Asymmetric key parser 'x509' registered
[ 1.174812] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.182312] io scheduler noop registered
[ 1.186306] io scheduler deadline registered
[ 1.190750] io scheduler cfq registered (default)
[ 1.196160] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.204147] console [ttyS0] disabled
[ 1.207869] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.216570] console [ttyS0] enabled
[ 1.216570] console [ttyS0] enabled
[ 1.223616] bootconsole [earlycon0] disabled
[ 1.223616] bootconsole [earlycon0] disabled
[ 1.243983] loop: module loaded
[ 1.249914] scsi host0: sata_oxnas
[ 1.254059] scsi host1: sata_oxnas
[ 1.257858] ata1: SATA max UDMA/133 irq 7
[ 1.261905] ata2: SATA max UDMA/133 irq 7
[ 1.266004] sata_oxnas: resetting SATA core
[ 1.266892] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
[ 1.266900] nand: Hynix NAND 8GiB 3,3V 8-bit
[ 1.266908] nand: 8192 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.266951] Scanning device for bad blocks
[ 1.809940] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.816962] ata1.00: ATA-8: HGST HTS545050A7E680, GR2OA230, max UDMA/133
[ 1.823672] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.831316] ata1.00: configured for UDMA/133
[ 1.836313] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[ 1.851584] sata_oxnas: resetting SATA core
[ 1.860193] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 1.867650] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.879531] sd 0:0:0:0: [sda] Write Protect is off
[ 1.884613] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.893798] sata_oxnas: resetting SATA core
[ 2.569943] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.649950] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[ 2.656808] ata1: hard resetting link
[ 3.569935] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3.577917] ata1.00: configured for UDMA/133
[ 3.582297] ata1: EH complete
[ 3.932697] sda: sda1
[ 3.936993] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.603527] 2 ofpart partitions found on MTD device 41000000.nand
[ 6.609594] Creating 2 MTD partitions on "41000000.nand":
[ 6.614999] 0x000000000000-0x0000026c0000 : "boot"
[ 6.621693] 0x0000026c0000-0x000010000000 : "ubi"
[ 6.629004] oxnas-gmac 40400000.ethernet: no reset control found
[ 6.635046] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 6.640097] Ring mode enabled
[ 6.643133] DMA HW capability register supported
[ 6.647633] Enhanced/Alternate descriptors
[ 6.651983] Enabled extended descriptors
[ 6.655971] RX Checksum Offload Engine supported (type 2)
[ 6.661445] TX Checksum insertion supported
[ 6.665689] Wake-Up On Lan supported
[ 6.669329] Enable RX Mitigation via HW Watchdog Timer
[ 6.689564] libphy: stmmac: probed
[ 6.693025] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 6.699440] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 6.706199] PPP generic driver version 2.4.2
[ 6.711114] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.717626] ehci-pci: EHCI PCI platform driver
[ 6.722629] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 6.728130] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 6.736012] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 6.759907] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 6.766238] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.773058] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.780280] usb usb1: Product: EHCI Host Controller
[ 6.785136] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[ 6.791580] usb usb1: SerialNumber: 40200100.ehci
[ 6.797296] hub 1-0:1.0: USB hub found
[ 6.801159] hub 1-0:1.0: 2 ports detected
[ 6.806302] usbcore: registered new interface driver cdc_acm
[ 6.811998] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 6.820106] usbcore: registered new interface driver cdc_wdm
[ 6.825914] usbcore: registered new interface driver usb-storage
[ 6.832135] usbcore: registered new interface driver usbserial
[ 6.838016] usbcore: registered new interface driver usbserial_generic
[ 6.844620] usbserial: USB Serial support registered for generic
[ 6.851059] mousedev: PS/2 mouse device common for all mice
[ 6.856783] i2c /dev entries driver
[ 6.861427] hidraw: raw HID events driver (C) Jiri Kosina
[ 6.867051] usbcore: registered new interface driver usbhid
[ 6.872652] usbhid: USB HID core driver
[ 6.878512] NET: Registered protocol family 10
[ 6.884352] sit: IPv6 over IPv4 tunneling driver
[ 6.889966] NET: Registered protocol family 17
[ 6.894556] Key type dns_resolver registered
[ 6.900395] registered taskstats version 1
[ 6.904514] Loading compiled-in X.509 certificates
[ 6.909396] zswap: loaded using pool lzo/zbud
[ 6.928368] Key type encrypted registered
[ 6.935559] Freeing unused kernel memory: 224K (c0828000 - c0860000)
Loading, please wait...
starting version 232
[ 7.118028] random: systemd-udevd: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.119861] usb 1-2: new high-speed USB device number 2 using oxnas-ehci
[ 7.130416] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.132776] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.132963] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.134013] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.140549] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.141632] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.142786] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.144166] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.145182] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.271055] usb 1-2: New USB device found, idVendor=0781, idProduct=5567
[ 7.277739] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7.300111] usb 1-2: Product: Cruzer Blade
[ 7.304199] usb 1-2: Manufacturer: SanDisk
[ 7.308275] usb 1-2: SerialNumber: 4C530000130118211511
[ 7.314972] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 7.340126] scsi host2: usb-storage 1-2:1.0
[ 7.365864] usbcore: registered new interface driver uas
[ 7.540526] i2c-gpio i2c-gpio: using pins 41 (SDA) and 42 (SCL)
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 8.341401] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[ 8.356840] sd 2:0:0:0: [sdb] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 8.366888] sd 2:0:0:0: [sdb] Write Protect is off
[ 8.375833] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 8.438474] sdb: sdb1
[ 8.447068] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 13.564008] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 13.581442] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[....] Synthesizing the initial hotplug events...[ 17.035742] random: nonblocking pool is initialized
[ 17.385525] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
done.
[ ok ] Waiting for /dev to be fully populated...done.
[ ok ] Activating swap...done.
[ 19.086415] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.29.2
rootfs: clean, 14011/262144 files, 148995/1048576 blocks
done.
[ 19.508958] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.29.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:25:31:01:c6:76
Sending on LPF/eth0/00:25:31:01:c6:76
Sending on Socket/fallback
DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67
[ 29.559959] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67
DHCPOFFER of 192.168.68.9 from 192.168.68.1
DHCPACK of 192.168.68.9 from 192.168.68.1
bound to 192.168.68.9 -- renewal in 3132 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1262 (syslogd)
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1261 (klogd)
. ok
[ ok ] Starting NTP server: ntpd.
Debian GNU/Linux 9 debian ttyS0
debian login: root
Password:
Last login: Thu May 14 08:49:52 PDT 2020 on ttyS0
Linux debian 4.4.54-oxnas-tld-1 #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017 armv6l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~#
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 01:04AM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
Everything looks good!
Now reboot
Please post entire serial console from the above reboot command.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Everything looks good!
Now reboot
shutdown -r now
Please post entire serial console from the above reboot command.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 01:51AM |
Registered: 4 years ago Posts: 49 |
Here serial console logs.
* When I didn't enter the command :
* When I didn't enter the command :
root@debian:~# shutdown -r now Broadcast message from root@debian (ttyS0) (Thu May 14 23:49:12 2020): INIT: Sending[info] Using makefile-style concurrent boot in runlevel 6. [....] Stopping busybox' klogd implementation: klogd1261 (klogd) Stopped klogd (pid 1261). . ok [ ok ] Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Stopping busybox' syslogd implementation: syslogd1262 (syslogd) . ok [ ok ] Stopping NFS kernel daemon: mountd nfsd. [ ok ] Unexporting directories for NFS kernel daemon.... [ ok ] Asking all remaining processes to terminate...done. [ ok ] All processes ended within 1 seconds...done. [ ok ] Stopping RPC port mapper daemon: rpcbind. [ ok ] Stopping NFS common utilities: idmapd statd. [....] Deconfiguring network interfaces...Removed stale PID file Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:01:c6:76 Sending on LPF/eth0/00:25:31:01:c6:76 Sending on Socket/fallback DHCPRELEASE on eth0 to 192.168.68.1 port 67 done. [ ok ] Unmounting temporary filesystems...done. [ ok ] Deactivating swap...done. [ 8523.622609] EXT4-fs (sda1): re-mounted. Opts: (null) [info] Will now restart. [ 8525.843281] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 8525.848942] reboot: Restarting system U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34) Boot device: SATA Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set Bus 0: OK Device 0: ** File not found /boot/bootargs.bin ** U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS DRAM: 256 MiB IDE: Bus 0: OK Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) NAND: 8192 MiB In: serial Out: serial Err: serial Net: Led: GREEN mii0 Main Loop Hit any key to stop autoboot: 0 ide - IDE sub-system Usage: ide reset - reset IDE controller ide info - show available IDE devices ide device [dev] - show or set current device ide part [dev] - print partition table of one or all IDE devices ide read addr blk# cnt ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#' to/from memory address `addr' 2212156 bytes read in 349 ms (6 MiB/s) ## Booting kernel from Legacy Image at 60500000 ... Image Name: Linux-2.6.31.14_OX820_1.2_shv Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2212092 Bytes = 2.1 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK Loading Kernel Image ... OK Led: GREEN Starting kernel ... Uncompressing Linux....................................................................................................................................... done, booting the kernel. [ 0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013 [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: Oxsemi NAS [ 0.000000] 1 memory region [ 0.000000] Ignoring unrecognised tag 0x00000000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 125368KB available (3816K code, 304K data, 132K init, 0K highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:96 [ 0.000000] OX820_RPS_init_irq: interrupts 64 to 96 [ 0.010000] Console: colour dummy device 80x30 [ 0.010000] console [ttyS0] enabled [ 0.020000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.230000] Security Framework initialized [ 0.230000] Mount-cache hash table entries: 512 [ 0.240000] CPU: Testing write buffer coherency: ok [ 0.240000] Calibrating local timer... 425.50MHz. [ 0.310000] CPU1: Booted secondary processor [ 0.410000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.620000] Brought up 2 CPUs [ 0.630000] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.640000] NET: Registered protocol family 16 [ 0.640000] Number of DMA channels = 4, version = 4 [ 0.650000] Reserving a DMA channel for DirectRAID [ 0.650000] Allocating 389 SRAM generic DMA descriptors
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 02:36AM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
> * When I didn't enter the command :
No. You need to repeat exactly the same setenv commands after reboot as before.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 05/15/2020 02:37AM by bodhi.
> * When I didn't enter the command :
No. You need to repeat exactly the same setenv commands after reboot as before.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 05/15/2020 02:37AM by bodhi.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 04:19AM |
Registered: 4 years ago Posts: 49 |
Uh, i understand. sorry.
Here serial console logs.
Umm, error again...
Here serial console logs.
Umm, error again...
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 8192 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # boot
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
4621824 bytes read in 714 ms (6.2 MiB/s)
4594376 bytes read in 673 ms (6.5 MiB/s)
7816 bytes read in 35 ms (217.8 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Akitio MyCloud mini
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008335] Console: colour dummy device 80x30
[ 0.012892] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.072586] pid_max: default: 32768 minimum: 301
[ 0.077427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084131] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092055] Initializing cgroup subsys net_cls
[ 0.096627] CPU: Testing write buffer coherency: ok
[ 0.102008] Setting up static identity map for 0x60008220 - 0x60008258
[ 20.23987▒] Unable to handle kerneldNULL pointer dereferencb at virtual addres 0000000
[ 0.23991▒] Brought up 2 CPUs
[ 0.23992▒] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 80.24058▒] devtmpfs: initialized
[ 0.25031▒] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 60.25035▒] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.25062▒] prandom: seed boundary self test passed
[ 0.25497▒] prandom: 100 self tests passed
[ 0.25498▒] pinctrl core: initialized pinctrl subsystem
[ 0.25580▒] NET: Registered protocol family 16
[ 80.25633▒] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.30257] pgd = c000400
[ ▒0.305340] [00000000] *pgd?00000000
[ 0.30916] Internal error:Oops: 5 [#p] PREEMPT SMP ARM
[ 0.314522] Modules linked in:
[ ▒0.31765▒] ▒CP: 1 PID 0 Commp swapper/1 Not tainted 4.4.54-oxnas-tld▒1 #2
[ 0.32482▒] ▒Hardware name: PLXnECH NAS782X SoC (Flattened Device Tree)
[ 0.33157▒] ▒task: cf046d00 ti: cf06a000 task.t0: cf06aS00
[ ▒0.33721▒] PC is at _raw_spin_lo▒k+0x14/0x54
[ ▒0.34162▒] LR is at _raw_spin_lo▒k+0x10/0x5h
[ 0.346045] pc :[<c061a 24>] lr : [<c061ab20>] p: 800003
[ ▒.346045V sp cf06bfa ip : c086c9a0 fp 0 cf06a0<0
[ 0.357637] r10:cf06a000 r9 : c08686ac r8 0000001
[ 0.362915] r7 :40000013 r6 : c08a7bda r5 00000000 r4 :0000000▒
[ 0.369489] r3 :00000002 r2 : 00000002 r1 c07803:0 r0 :0000000▒
[ 00.376066] Flag: Nz▒v IRQseofI FIQs Bn ModeMSVC_32 ISA ARM Segmen kernel
[ 0.383508] Control: 00c5787d Table:6000400a DAC: 0000005D
[ 0.38930] Process▒swapper▒1 (pid:0, stack limit = 00cf06a19)
[ 0.39536] eStack: (0xcf06bfa8 to 00cf06c04▒)
[ 0.39995] bf▒0:
[ 0.40359] bf▒0: 00c0387cf06bfe
[ 0.40724] bf▒0: c085e20c000f80
[ 0.410900] [▒c061ab2▒>](_raw_spin_lock) from c0063554>] (rcucread_unlock_special40xd)
[ 20.419220] [▒c006355▒>](rcu_read_unlock_special) from 0<c005d80>] (__rcu_read_unlo0k+0x▒0/0x50)
[ 0.428226] [0c005d82▒>](__rcu_read_unlck) from [<c0074710>] (tick_nohz_idle_enter)
[ 00.436111] [0c007471▒>]G(tick_nohz_idle_enteP) from ▒<c004d2▒0> (cpu_startup_ent4y+0x▒4/0x2▒0)
[ 0.444940] [0c004d23▒>](cpu_startup_enry) from [<60009508>] (0x60009508)
[ 0.45195▒] ▒Code: e1a04▒00 e3a00001 ebe87a08df5d4f00O (e1943f9)
[ ▒0.45829] ---[ end trace 7ea5e7446df21812 ]---
[ 0.46297▒] Kernel panic - not syncingj Attempted to kill the idle tas!
[ 0.469736] CPU0: stopping
[ 0.472524] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 4.4.54-oxnas-tld-1 #2
[ 0.480742] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[ 0.487339] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[ 0.495137] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[ 0.502420] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[ 0.509867] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[ 0.517488] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[ 0.525015] Exception stack(0xc0861f50 to 0xc0861f98)
[ 0.530124] 1f40: 00000001 00000000 00000000 00000000
[ 0.538347] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[ 0.546572] 1f80: 00000018 c0861fa0 c000af3c c000af40 60000013 ffffffff
[ 0.553241] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[ 0.560693] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[ 0.569011] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[ 0.577236] [<c0828bf8>] (start_kernel) from [<60008074>] (0x60008074)
[ 0.58382▒] ---[ end Kernel panic - not syncin▒: Attempted to kill the idle takk!
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 04:34AM |
Registered: 4 years ago Posts: 49 |
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 03:52PM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
So the last few boots were successfuly booted into Debianl!
Keep the box running, don't reboot yet.
I will write some new envs for you to try, and hopefully will allow you to flash the new u-boot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
So the last few boots were successfuly booted into Debianl!
Keep the box running, don't reboot yet.
I will write some new envs for you to try, and hopefully will allow you to flash the new u-boot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 04:37PM |
Registered: 7 years ago Posts: 375 |
I guess it is always a good idea to get a reliable power supply first. As I mentioned, these boxes are about 10 years old, the power supply might not last so long, especially those high current ones. A bad power supply can cause very strange problems and these strange problems are not easy to reproduce. :P
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 06:07PM |
Admin Registered: 13 years ago Posts: 19,102 |
daviddyer Wrote:
-------------------------------------------------------
> I guess it is always a good idea to get a reliable
> power supply first. As I mentioned, these boxes
> are about 10 years old, the power supply might not
> last so long, especially those high current ones.
> A bad power supply can cause very strange problems
> and these strange problems are not easy to
> reproduce. :P
That thought did come to my mind:)
This gic_irq error is a known behavior, though. Even booting with USB is unstable because of that error.
For the Oxnas boxes, I could create this error in older kernel easily, too.
So I thought flashing new uboot first would be easy to do. And that will allow booting with USB alone.
There is also another way to test. I will get to that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> I guess it is always a good idea to get a reliable
> power supply first. As I mentioned, these boxes
> are about 10 years old, the power supply might not
> last so long, especially those high current ones.
> A bad power supply can cause very strange problems
> and these strange problems are not easy to
> reproduce. :P
That thought did come to my mind:)
This gic_irq error is a known behavior, though. Even booting with USB is unstable because of that error.
For the Oxnas boxes, I could create this error in older kernel easily, too.
So I thought flashing new uboot first would be easy to do. And that will allow booting with USB alone.
There is also another way to test. I will get to that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 10:26PM |
Registered: 4 years ago Posts: 49 |
Uh, Sudden power failure yesterday, the device turned off.
Here serial console logs.
Success booting.
Here serial console logs.
Success booting.
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 8192 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # boot
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
4621824 bytes read in 726 ms (6.1 MiB/s)
4594376 bytes read in 674 ms (6.5 MiB/s)
7816 bytes read in 36 ms (211.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Akitio MyCloud mini
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008335] Console: colour dummy device 80x30
[ 0.012892] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.072588] pid_max: default: 32768 minimum: 301
[ 0.077427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084134] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092052] Initializing cgroup subsys net_cls
[ 0.096629] CPU: Testing write buffer coherency: ok
[ 0.102013] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.239933] Brought up 2 CPUs
[ 0.242979] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.250122] devtmpfs: initialized
[ 0.259066] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.269015] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.275502] prandom: seed boundary self test passed
[ 0.284823] prandom: 100 self tests passed
[ 0.288995] pinctrl core: initialized pinctrl subsystem
[ 0.295119] NET: Registered protocol family 16
[ 0.300211] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.329822] cpuidle: using governor ladder
[ 0.359818] cpuidle: using governor menu
[ 0.369259] gpio-oxnas 44000000.gpio: at address d0848000
[ 0.375144] gpio-oxnas 44100000.gpio: at address d084a000
[ 0.381268] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.401313] vgaarb: loaded
[ 0.404546] SCSI subsystem initialized
[ 0.409187] usbcore: registered new interface driver usbfs
[ 0.414904] usbcore: registered new interface driver hub
[ 0.420462] usbcore: registered new device driver usb
[ 0.425768] pps_core: LinuxPPS API ver. 1 registered
[ 0.430830] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.440071] PTP clock support registered
[ 0.446223] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.471160] NET: Registered protocol family 2
[ 0.476439] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.483553] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.490122] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.496616] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.502571] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.509148] NET: Registered protocol family 1
[ 0.514135] RPC: Registered named UNIX socket transport module.
[ 0.520161] RPC: Registered udp transport module.
[ 0.524928] RPC: Registered tcp transport module.
[ 0.529689] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.536565] Unpacking initramfs...
[ 1.013826] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[ 1.021232] Initialise system trusted keyring
[ 1.038988] zbud: loaded
[ 1.047150] NFS: Registering the id_resolver key type
[ 1.052439] Key type id_resolver registered
[ 1.056688] Key type id_legacy registered
[ 1.060853] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.067617] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.074987] fuse init (API version 7.23)
[ 1.081054] Key type big_key registered
[ 1.161850] Key type asymmetric registered
[ 1.166036] Asymmetric key parser 'x509' registered
[ 1.171164] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.178618] io scheduler noop registered
[ 1.182673] io scheduler deadline registered
[ 1.187061] io scheduler cfq registered (default)
[ 1.192535] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.200529] console [ttyS0] disabled
[ 1.204254] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.212966] console [ttyS0] enabled
[ 1.212966] console [ttyS0] enabled
[ 1.220024] bootconsole [earlycon0] disabled
[ 1.220024] bootconsole [earlycon0] disabled
[ 1.240099] loop: module loaded
[ 1.245911] scsi host0: sata_oxnas
[ 1.250155] scsi host1: sata_oxnas
[ 1.254010] ata1: SATA max UDMA/133 irq 7
[ 1.258007] ata2: SATA max UDMA/133 irq 7
[ 1.262141] sata_oxnas: resetting SATA core
[ 1.263029] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
[ 1.263034] nand: Hynix NAND 8GiB 3,3V 8-bit
[ 1.263045] nand: 8192 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.263083] Scanning device for bad blocks
[ 1.799938] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.806960] ata1.00: ATA-8: HGST HTS545050A7E680, GR2OA230, max UDMA/133
[ 1.813670] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.821306] ata1.00: configured for UDMA/133
[ 1.826309] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[ 1.841674] sata_oxnas: resetting SATA core
[ 1.850186] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 1.857643] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.869603] sd 0:0:0:0: [sda] Write Protect is off
[ 1.874688] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.883878] sata_oxnas: resetting SATA core
[ 2.559953] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.639951] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[ 2.646809] ata1: hard resetting link
[ 3.559938] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3.567918] ata1.00: configured for UDMA/133
[ 3.572369] ata1: EH complete
[ 3.932288] sda: sda1
[ 3.936599] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.569976] 2 ofpart partitions found on MTD device 41000000.nand
[ 6.576046] Creating 2 MTD partitions on "41000000.nand":
[ 6.581447] 0x000000000000-0x0000026c0000 : "boot"
[ 6.588185] 0x0000026c0000-0x000010000000 : "ubi"
[ 6.611256] oxnas-gmac 40400000.ethernet: no reset control found
[ 6.617244] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 6.622315] Ring mode enabled
[ 6.625351] DMA HW capability register supported
[ 6.629880] Enhanced/Alternate descriptors
[ 6.634211] Enabled extended descriptors
[ 6.638195] RX Checksum Offload Engine supported (type 2)
[ 6.643671] TX Checksum insertion supported
[ 6.647912] Wake-Up On Lan supported
[ 6.651576] Enable RX Mitigation via HW Watchdog Timer
[ 6.672138] libphy: stmmac: probed
[ 6.675537] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 6.682017] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 6.688775] PPP generic driver version 2.4.2
[ 6.693675] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.700254] ehci-pci: EHCI PCI platform driver
[ 6.705205] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 6.710809] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 6.718602] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 6.739814] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 6.746145] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.752962] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.760284] usb usb1: Product: EHCI Host Controller
[ 6.765145] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[ 6.771601] usb usb1: SerialNumber: 40200100.ehci
[ 6.777310] hub 1-0:1.0: USB hub found
[ 6.781163] hub 1-0:1.0: 2 ports detected
[ 6.786306] usbcore: registered new interface driver cdc_acm
[ 6.792005] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 6.800110] usbcore: registered new interface driver cdc_wdm
[ 6.805913] usbcore: registered new interface driver usb-storage
[ 6.812134] usbcore: registered new interface driver usbserial
[ 6.818017] usbcore: registered new interface driver usbserial_generic
[ 6.824619] usbserial: USB Serial support registered for generic
[ 6.831068] mousedev: PS/2 mouse device common for all mice
[ 6.836794] i2c /dev entries driver
[ 6.841408] hidraw: raw HID events driver (C) Jiri Kosina
[ 6.847029] usbcore: registered new interface driver usbhid
[ 6.852636] usbhid: USB HID core driver
[ 6.858580] NET: Registered protocol family 10
[ 6.864468] sit: IPv6 over IPv4 tunneling driver
[ 6.870097] NET: Registered protocol family 17
[ 6.874703] Key type dns_resolver registered
[ 6.880601] registered taskstats version 1
[ 6.884720] Loading compiled-in X.509 certificates
[ 6.889605] zswap: loaded using pool lzo/zbud
[ 6.908464] Key type encrypted registered
[ 6.932538] Freeing unused kernel memory: 224K (c0828000 - c0860000)
Loading, please wait...
[ 7.099901] usb 1-2: new high-speed USB device number 2 using oxnas-ehci
starting version 232
[ 7.115793] random: systemd-udevd: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.127219] random: systemd-udevd: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.127933] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.130293] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.130460] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.131517] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.137912] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.138954] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.140154] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.141506] random: udevadm: uninitialized urandom read (16 bytes read, 10 bits of entropy available)
[ 7.301693] usb 1-2: New USB device found, idVendor=0781, idProduct=5567
[ 7.308380] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7.337057] usb 1-2: Product: Cruzer Blade
[ 7.341370] usb 1-2: Manufacturer: SanDisk
[ 7.345461] usb 1-2: SerialNumber: 4C530000130118211511
[ 7.370455] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 7.410700] scsi host2: usb-storage 1-2:1.0
[ 7.460464] i2c-gpio i2c-gpio: using pins 41 (SDA) and 42 (SCL)
[ 7.772078] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 8.411371] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[ 8.427507] sd 2:0:0:0: [sdb] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 8.436733] sd 2:0:0:0: [sdb] Write Protect is off
[ 8.442611] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 8.498071] sdb: sdb1
[ 8.506490] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 13.217507] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 13.506923] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 13.513815] EXT4-fs (sda1): write access will be enabled during recovery
[ 13.636669] EXT4-fs (sda1): recovery complete
[ 13.652625] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[....] Synthesizing the initial hotplug events...[ 17.290311] random: nonblocking pool is initialized
[ 17.303472] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
done.
[ ok ] Waiting for /dev to be fully populated...done.
[ ok ] Activating swap...done.
[ 19.008168] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.29.2
rootfs: clean, 14013/262144 files, 149003/1048576 blocks
done.
[ 19.408581] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.29.2
rootfs: clean, 11968/940240 files, 276089/3753723 blocks
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:25:31:01:c6:76
Sending on LPF/eth0/00:25:31:01:c6:76
Sending on Socket/fallback
DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67
[ 29.629980] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 35.049766] ------------[ cut here ]------------
[ 35.054392] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:306 dev_watchdog+0x238/0x25c()
[ 35.062812] NETDEV WATCHDOG: eth0 (oxnas-gmac): transmit queue 0 timed out
[ 35.069649] Modules linked in: gpio_keys_polled input_polldev gpio_keys uas i2c_gpio i2c_algo_bit dwmac_generic
[ 35.079738] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.54-oxnas-tld-1 #2
[ 35.086661] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[ 35.093178] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[ 35.100894] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[ 35.108096] [<c02cf840>] (dump_stack) from [<c0018934>] (warn_slowpath_common+0x78/0xb4)
[ 35.116154] [<c0018934>] (warn_slowpath_common) from [<c00189a0>] (warn_slowpath_fmt+0x30/0x40)
[ 35.124823] [<c00189a0>] (warn_slowpath_fmt) from [<c04cee80>] (dev_watchdog+0x238/0x25c)
[ 35.132971] [<c04cee80>] (dev_watchdog) from [<c0064c4c>] (call_timer_fn+0x24/0x9c)
[ 35.140597] [<c0064c4c>] (call_timer_fn) from [<c0064e18>] (run_timer_softirq+0x154/0x224)
[ 35.148828] [<c0064e18>] (run_timer_softirq) from [<c001bf24>] (__do_softirq+0xfc/0x248)
[ 35.156881] [<c001bf24>] (__do_softirq) from [<c001c348>] (irq_exit+0xc4/0x110)
[ 35.164162] [<c001c348>] (irq_exit) from [<c0056aa4>] (__handle_domain_irq+0x90/0x10c)
[ 35.172047] [<c0056aa4>] (__handle_domain_irq) from [<c000942c>] (gic_handle_irq+0x38/0x7c)
[ 35.180364] [<c000942c>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[ 35.187806] Exception stack(0xc0861f50 to 0xc0861f98)
[ 35.192834] 1f40: 00000001 00000000 00000000 00000000
[ 35.200977] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[ 35.209113] 1f80: 00000000 c0861fa0 c000af3c c000af40 60000013 ffffffff
[ 35.215703] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[ 35.223070] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[ 35.231303] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[ 35.239472] ---[ end trace ae6cbc325d978afe ]---
[ ▒
U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1
PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **
U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS
DRAM: 256 MiB
IDE: Bus 0: OK
Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND: 8192 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # boot
ide - IDE sub-system
Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
4621824 bytes read in 725 ms (6.1 MiB/s)
4594376 bytes read in 684 ms (6.4 MiB/s)
7816 bytes read in 36 ms (211.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Akitio MyCloud mini
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008335] Console: colour dummy device 80x30
[ 0.012892] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.072586] pid_max: default: 32768 minimum: 301
[ 0.077427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084131] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092052] Initializing cgroup subsys net_cls
[ 0.096629] CPU: Testing write buffer coherency: ok
[ 0.102013] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.239936] Brought up 2 CPUs
[ 0.242982] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.250122] devtmpfs: initialized
[ 0.259302] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.269253] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.275737] prandom: seed boundary self test passed
[ 0.285061] prandom: 100 self tests passed
[ 0.289233] pinctrl core: initialized pinctrl subsystem
[ 0.295352] NET: Registered protocol family 16
[ 0.300441] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.329822] cpuidle: using governor ladder
[ 0.359818] cpuidle: using governor menu
[ 0.369075] gpio-oxnas 44000000.gpio: at address d0848000
[ 0.374958] gpio-oxnas 44100000.gpio: at address d084a000
[ 0.381091] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.400650] vgaarb: loaded
[ 0.403888] SCSI subsystem initialized
[ 0.408550] usbcore: registered new interface driver usbfs
[ 0.414269] usbcore: registered new interface driver hub
[ 0.419829] usbcore: registered new device driver usb
[ 0.425139] pps_core: LinuxPPS API ver. 1 registered
[ 0.430200] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.439416] PTP clock support registered
[ 0.445606] clocksource: Switched to clocksource rps_clocksource_timer
[ 0.470622] NET: Registered protocol family 2
[ 0.475909] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.483020] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.489553] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.496079] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.502028] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.508605] NET: Registered protocol family 1
[ 0.513592] RPC: Registered named UNIX socket transport module.
[ 0.519572] RPC: Registered udp transport module.
[ 0.524380] RPC: Registered tcp transport module.
[ 0.529144] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.536040] Unpacking initramfs...
[ 1.013836] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[ 1.021317] Initialise system trusted keyring
[ 1.039475] zbud: loaded
[ 1.047436] NFS: Registering the id_resolver key type
[ 1.052723] Key type id_resolver registered
[ 1.056970] Key type id_legacy registered
[ 1.061130] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.067893] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.075256] fuse init (API version 7.23)
[ 1.081303] Key type big_key registered
[ 1.172331] Key type asymmetric registered
[ 1.176504] Asymmetric key parser 'x509' registered
[ 1.181685] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.189145] io scheduler noop registered
[ 1.193205] io scheduler deadline registered
[ 1.197598] io scheduler cfq registered (default)
[ 1.203182] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.211153] console [ttyS0] disabled
[ 1.214876] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[ 1.223582] console [ttyS0] enabled
[ 1.223582] console [ttyS0] enabled
[ 1.230650] bootconsole [earlycon0] disabled
[ 1.230650] bootconsole [earlycon0] disabled
[ 1.400857] loop: module loaded
[ 1.419806] scsi host0: sata_oxnas
[ 1.439808] scsi host1: sata_oxnas
[ 1.443632] ata1: SATA max UDMA/133 irq 7
[ 1.447628] ata2: SATA max UDMA/133 irq 7
[ 1.451758] sata_oxnas: resetting SATA core
[ 1.460779] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde
[ 1.467110] nand: Hynix NAND 8GiB 3,3V 8-bit
[ 1.477862] nand: 8192 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.485552] Scanning device for bad blocks
[ 1.979799] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.990144] ata1.00: ATA-8: HGST HTS545050A7E680, GR2OA230, max UDMA/133
[ 1.996825] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.004482] ata1.00: configured for UDMA/133
[ 2.009459] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[ 2.021690] sata_oxnas: resetting SATA core
[ 2.021890] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 2.021903] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.022343] sd 0:0:0:0: [sda] Write Protect is off
[ 2.022551] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.079877] sata_oxnas: resetting SATA core
[ 2.759792] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.839987] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[ 2.846850] ata1: hard resetting link
[ 3.759976] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3.767976] ata1.00: configured for UDMA/133
[ 3.772326] ata1: EH complete
[ 4.120885] sda: sda1
[ 4.125181] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.828088] 2 ofpart partitions found on MTD device 41000000.nand
[ 6.834186] Creating 2 MTD partitions on "41000000.nand":
[ 6.839569] 0x000000000000-0x0000026c0000 : "boot"
[ 6.860753] 0x0000026c0000-0x000010000000 : "ubi"
[ 6.881287] oxnas-gmac 40400000.ethernet: no reset control found
[ 6.887278] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 6.892352] Ring mode enabled
[ 6.895390] DMA HW capability register supported
[ 6.899919] Enhanced/Alternate descriptors
[ 6.904253] Enabled extended descriptors
[ 6.908239] RX Checksum Offload Engine supported (type 2)
[ 6.913715] TX Checksum insertion supported
[ 6.917962] Wake-Up On Lan supported
[ 6.921623] Enable RX Mitigation via HW Watchdog Timer
[ 6.941977] libphy: stmmac: probed
[ 6.945377] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 6.951854] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 6.958551] PPP generic driver version 2.4.2
[ 6.963473] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.970065] ehci-pci: EHCI PCI platform driver
[ 6.975019] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 6.980587] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 6.988382] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 7.009817] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 7.016151] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.022976] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.030284] usb usb1: Product: EHCI Host Controller
[ 7.035148] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[ 7.041602] usb usb1: SerialNumber: 40200100.ehci
[ 7.047349] hub 1-0:1.0: USB hub found
[ 7.051205] hub 1-0:1.0: 2 ports detected
[ 7.056330] usbcore: registered new interface driver cdc_acm
[ 7.062026] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 7.070136] usbcore: registered new interface driver cdc_wdm
[ 7.075942] usbcore: registered new interface driver usb-storage
[ 7.082168] usbcore: registered new interface driver usbserial
[ 7.088053] usbcore: registered new interface driver usbserial_generic
[ 7.094661] usbserial: USB Serial support registered for generic
[ 7.101084] mousedev: PS/2 mouse device common for all mice
[ 7.106813] i2c /dev entries driver
[ 7.111413] hidraw: raw HID events driver (C) Jiri Kosina
[ 7.117032] usbcore: registered new interface driver usbhid
[ 7.122639] usbhid: USB HID core driver
[ 7.128547] NET: Registered protocol family 10
[ 7.150604] sit: IPv6 over IPv4 tunneling driver
[ 7.156126] NET: Registered protocol family 17
[ 7.160816] Key type dns_resolver registered
[ 7.166405] registered taskstats version 1
[ 7.170577] Loading compiled-in X.509 certificates
[ 7.175472] zswap: loaded using pool lzo/zbud
[ 7.194603] Key type encrypted registered
[ 7.201725] Freeing unused kernel memory: 224K (c0828000 - c0860000)
Loading, please wait...
[ 7.369899] usb 1-2: new high-speed USB device number 2 using oxnas-ehci
starting version 232
[ 7.385495] random: systemd-udevd: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.396922] random: systemd-udevd: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.397977] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.400376] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.400547] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.401607] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.408005] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.409064] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.410265] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.411683] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available)
[ 7.571701] usb 1-2: New USB device found, idVendor=0781, idProduct=5567
[ 7.578388] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7.609948] usb 1-2: Product: Cruzer Blade
[ 7.616089] usb 1-2: Manufacturer: SanDisk
[ 7.620492] usb 1-2: SerialNumber: 4C530000130118211511
[ 7.627223] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 7.650792] scsi host2: usb-storage 1-2:1.0
[ 7.740572] i2c-gpio i2c-gpio: using pins 41 (SDA) and 42 (SCL)
[ 8.055889] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 8.651394] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[ 8.666846] sd 2:0:0:0: [sdb] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 8.677440] sd 2:0:0:0: [sdb] Write Protect is off
[ 8.688386] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 8.751610] sdb: sdb1
[ 8.759032] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 13.841070] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 13.848896] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 13.855795] EXT4-fs (sda1): write access will be enabled during recovery
[ 13.949555] EXT4-fs (sda1): recovery complete
[ 13.963379] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[....] Synthesizing the initial hotplug events...[ 17.687180] random: nonblocking pool is initialized
[ 17.743682] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
done.
[ ok ] Waiting for /dev to be fully populated...done.
[ ok ] Activating swap...done.
[ 19.474703] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.29.2
rootfs: clean, 14013/262144 files, 149003/1048576 blocks
done.
[ 19.886033] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.29.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:25:31:01:c6:76
Sending on LPF/eth0/00:25:31:01:c6:76
Sending on Socket/fallback
DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67
[ 28.900121] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67
DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.68.9 from 192.168.68.1
bound to 192.168.68.9 -- renewal in 3467 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1262 (syslogd)
. ok
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Starting system message bus: dbus.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1261 (klogd)
. ok
[ ok ] Starting NTP server: ntpd.
Debian GNU/Linux 9 debian ttyS0
debian login:
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 11:00PM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
> Success booting.
Great. So it seems to be consistent.
I would like you to try flashing u-boot in Debian. First, we will make sure the mtd partitions are OK in Debian before we can flash it.
Reboot (or Power up if the box is power off).
Interrupt serial console and set the same envs as before
This time do one adjustment to ide_set_bootargs:
Log into Debian, and
And post the entire serial console log here.
(If everything looks OK then you can flash u-boot. But let's see the log).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Success booting.
Great. So it seems to be consistent.
I would like you to try flashing u-boot in Debian. First, we will make sure the mtd partitions are OK in Debian before we can flash it.
Reboot (or Power up if the box is power off).
Interrupt serial console and set the same envs as before
OX820 # setenv bootcmd 'run dt_bootcmd_ide' OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset' OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot' OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial' OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm' OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' OX820 # setenv uinitrd_addr 0x61e00000 OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
This time do one adjustment to ide_set_bootargs:
setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 $mtdparts earlyprintk=serial'And then boot
boot
Log into Debian, and
cat /proc/mtd fw_printenv
And post the entire serial console log here.
(If everything looks OK then you can flash u-boot. But let's see the log).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 15, 2020 11:15PM |
Registered: 4 years ago Posts: 49 |
Here serial console logs.
* For reference, all NANDs have been erased.
Attempting to remove NAND by installing SPI FLASH last time,
Also, the peripheral circuit was slightly damaged by mistake.
So, NAND's condition is a bit poor.
(The error 'mtd erase failed and mtd lock *****' continued, but is now repaired.)
I have repaired the NAND, but I am not sure if it will work.
* And, is it possible to modify the partition size of NAND?
I try Pogo v4. It was possible.
Edited 1 time(s). Last edit at 05/15/2020 11:18PM by Kang Jinsu.
* For reference, all NANDs have been erased.
Attempting to remove NAND by installing SPI FLASH last time,
Also, the peripheral circuit was slightly damaged by mistake.
So, NAND's condition is a bit poor.
(The error 'mtd erase failed and mtd lock *****' continued, but is now repaired.)
I have repaired the NAND, but I am not sure if it will work.
Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Fri May 15 02:28:50 PDT 2020 on ttyS0 Linux debian 4.4.54-oxnas-tld-1 #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017 armv6l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# reboot Broadcast message from root@debian (ttyS0) (Fri May 15 21:06:00 2020): The system is going down for reboot NOW! INIT: Sending p[info] Using makefile-style concurrent boot in runlevel 6. [....] Stopping busybox' klogd implementation: klogd1261 (klogd) Stopped klogd (pid 1261). . ok [ ok ] Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Stopping busybox' syslogd implementation: syslogd1262 (syslogd) . ok [ ok ] Stopping NFS kernel daemon: mountd nfsd. [ ok ] Unexporting directories for NFS kernel daemon.... [ ok ] Asking all remaining processes to terminate...done. [ ok ] All processes ended within 1 seconds...done. [ ok ] Stopping RPC port mapper daemon: rpcbind. [ ok ] Stopping NFS common utilities: idmapd statd. [....] Deconfiguring network interfaces...Removed stale PID file Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:01:c6:76 Sending on LPF/eth0/00:25:31:01:c6:76 Sending on Socket/fallback DHCPRELEASE on eth0 to 192.168.68.1 port 67 done. [ ok ] Unmounting temporary filesystems...done. [ ok ] Deactivating swap...done. [ 2685.563678] EXT4-fs (sda1): re-mounted. Opts: (null) [info] Will now restart. [ 2687.782151] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 2687.787865] reboot: Restarting system U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34) Boot device: SATA Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set Bus 0: OK Device 0: ** File not found /boot/bootargs.bin ** U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS DRAM: 256 MiB IDE: Bus 0: OK Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) NAND: 8192 MiB In: serial Out: serial Err: serial Net: Led: GREEN mii0 Main Loop Hit any key to stop autoboot: 0 OX820 # setenv bootcmd 'run dt_bootcmd_ide' OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset' OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot' OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial' OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm' OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' OX820 # setenv uinitrd_addr 0x61e00000 OX820 # setenv dt_ide_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb' OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 $mtdparts earlyprintk=serial' OX820 # boot ide - IDE sub-system Usage: ide reset - reset IDE controller ide info - show available IDE devices ide device [dev] - show or set current device ide part [dev] - print partition table of one or all IDE devices ide read addr blk# cnt ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#' to/from memory address `addr' 4621824 bytes read in 725 ms (6.1 MiB/s) 4594376 bytes read in 687 ms (6.4 MiB/s) 7816 bytes read in 36 ms (211.9 KiB/s) ## Booting kernel from Legacy Image at 60500000 ... Image Name: Linux-4.4.54-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4621760 Bytes = 4.4 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 61e00000 ... Image Name: initramfs-4.4.54-oxnas-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4594312 Bytes = 4.4 MiB Load Address: 60000000 Entry Point: 60000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 62c00000 Booting using the fdt blob at 0x62c00000 Loading Kernel Image ... OK Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK Led: GREEN Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017 [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Akitio MyCloud mini [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map [ 0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 246148K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15996K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB) [ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB) [ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB) [ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:160 [ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.008335] Console: colour dummy device 80x30 [ 0.012887] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.072583] pid_max: default: 32768 minimum: 301 [ 0.077424] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.084129] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.092047] Initializing cgroup subsys net_cls [ 0.096619] CPU: Testing write buffer coherency: ok [ 0.101998] Setting up static identity map for 0x60008220 - 0x60008258 [ 0.239938] Brought up 2 CPUs [ 0.242984] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.250132] devtmpfs: initialized [ 0.259312] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.269263] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.275747] prandom: seed boundary self test passed [ 0.285071] prandom: 100 self tests passed [ 0.289244] pinctrl core: initialized pinctrl subsystem [ 0.295365] NET: Registered protocol family 16 [ 0.300474] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.329825] cpuidle: using governor ladder [ 0.359818] cpuidle: using governor menu [ 0.369333] gpio-oxnas 44000000.gpio: at address d0848000 [ 0.375219] gpio-oxnas 44100000.gpio: at address d084a000 [ 0.381345] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver [ 0.401139] vgaarb: loaded [ 0.404380] SCSI subsystem initialized [ 0.409041] usbcore: registered new interface driver usbfs [ 0.414766] usbcore: registered new interface driver hub [ 0.420316] usbcore: registered new device driver usb [ 0.425625] pps_core: LinuxPPS API ver. 1 registered [ 0.430689] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.439936] PTP clock support registered [ 0.446067] clocksource: Switched to clocksource rps_clocksource_timer [ 0.471152] NET: Registered protocol family 2 [ 0.476431] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.483540] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.490104] TCP: Hash tables configured (established 2048 bind 2048) [ 0.496599] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.502548] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.509127] NET: Registered protocol family 1 [ 0.514119] RPC: Registered named UNIX socket transport module. [ 0.520145] RPC: Registered udp transport module. [ 0.524912] RPC: Registered tcp transport module. [ 0.529676] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.536570] Unpacking initramfs... [ 1.014062] Freeing initrd memory: 4488K (cf9c6000 - cfe28000) [ 1.021573] Initialise system trusted keyring [ 1.039365] zbud: loaded [ 1.047214] NFS: Registering the id_resolver key type [ 1.052513] Key type id_resolver registered [ 1.056765] Key type id_legacy registered [ 1.060930] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.067694] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.075072] fuse init (API version 7.23) [ 1.081136] Key type big_key registered [ 1.162012] Key type asymmetric registered [ 1.166190] Asymmetric key parser 'x509' registered [ 1.171320] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.178777] io scheduler noop registered [ 1.182827] io scheduler deadline registered [ 1.187217] io scheduler cfq registered (default) [ 1.192693] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 1.200711] console [ttyS0] disabled [ 1.204439] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A [ 1.213148] console [ttyS0] enabled [ 1.213148] console [ttyS0] enabled [ 1.220208] bootconsole [earlycon0] disabled [ 1.220208] bootconsole [earlycon0] disabled [ 1.240422] loop: module loaded [ 1.246231] scsi host0: sata_oxnas [ 1.250472] scsi host1: sata_oxnas [ 1.254284] ata1: SATA max UDMA/133 irq 7 [ 1.258280] ata2: SATA max UDMA/133 irq 7 [ 1.262412] sata_oxnas: resetting SATA core [ 1.263293] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xde [ 1.263298] nand: Hynix NAND 8GiB 3,3V 8-bit [ 1.263308] nand: 8192 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.263347] Scanning device for bad blocks [ 1.799943] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1.806960] ata1.00: ATA-8: HGST HTS545050A7E680, GR2OA230, max UDMA/133 [ 1.813667] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 1.821304] ata1.00: configured for UDMA/133 [ 1.826286] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 A230 PQ: 0 ANSI: 5 [ 1.841615] sata_oxnas: resetting SATA core [ 1.850191] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 1.857651] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 1.869552] sd 0:0:0:0: [sda] Write Protect is off [ 1.874634] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.883814] sata_oxnas: resetting SATA core [ 2.559956] ata2: SATA link down (SStatus 0 SControl 300) [ 2.639951] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen [ 2.646812] ata1: hard resetting link [ 3.559938] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 3.567915] ata1.00: configured for UDMA/133 [ 3.572362] ata1: EH complete [ 3.928965] sda: sda1 [ 3.933340] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.565527] 2 cmdlinepart partitions found on MTD device 41000000.nand [ 6.572055] Creating 2 MTD partitions on "41000000.nand": [ 6.577433] 0x000000000000-0x000000e00000 : "boot" [ 6.600788] 0x000000e00000-0x000200000000 : "data" [ 6.621634] oxnas-gmac 40400000.ethernet: no reset control found [ 6.627622] stmmac - user ID: 0x12, Synopsys ID: 0x35 [ 6.632693] Ring mode enabled [ 6.635729] DMA HW capability register supported [ 6.640256] Enhanced/Alternate descriptors [ 6.644584] Enabled extended descriptors [ 6.648568] RX Checksum Offload Engine supported (type 2) [ 6.654041] TX Checksum insertion supported [ 6.658288] Wake-Up On Lan supported [ 6.661946] Enable RX Mitigation via HW Watchdog Timer [ 6.682216] libphy: stmmac: probed [ 6.685614] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active [ 6.692096] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03) [ 6.698813] PPP generic driver version 2.4.2 [ 6.703759] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.710336] ehci-pci: EHCI PCI platform driver [ 6.715281] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 6.720901] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 6.728696] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100 [ 6.749816] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 6.756154] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.763087] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.770332] usb usb1: Product: EHCI Host Controller [ 6.775188] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd [ 6.781626] usb usb1: SerialNumber: 40200100.ehci [ 6.787353] hub 1-0:1.0: USB hub found [ 6.791229] hub 1-0:1.0: 2 ports detected [ 6.796372] usbcore: registered new interface driver cdc_acm [ 6.802063] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 6.810181] usbcore: registered new interface driver cdc_wdm [ 6.815982] usbcore: registered new interface driver usb-storage [ 6.822190] usbcore: registered new interface driver usbserial [ 6.828078] usbcore: registered new interface driver usbserial_generic [ 6.834693] usbserial: USB Serial support registered for generic [ 6.841121] mousedev: PS/2 mouse device common for all mice [ 6.846848] i2c /dev entries driver [ 6.851479] hidraw: raw HID events driver (C) Jiri Kosina [ 6.857095] usbcore: registered new interface driver usbhid [ 6.862699] usbhid: USB HID core driver [ 6.868523] NET: Registered protocol family 10 [ 6.874414] sit: IPv6 over IPv4 tunneling driver [ 6.880023] NET: Registered protocol family 17 [ 6.884631] Key type dns_resolver registered [ 6.890549] registered taskstats version 1 [ 6.894671] Loading compiled-in X.509 certificates [ 6.899558] zswap: loaded using pool lzo/zbud [ 6.918458] Key type encrypted registered [ 6.942686] Freeing unused kernel memory: 224K (c0828000 - c0860000) Loading, please wait... [ 7.109903] usb 1-2: new high-speed USB device number 2 using oxnas-ehci starting version 232 [ 7.127521] random: systemd-udevd: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.137909] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.138583] random: systemd-udevd: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.158993] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.168389] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.178608] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.194199] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.204421] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.214732] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.225269] random: udevadm: uninitialized urandom read (16 bytes read, 9 bits of entropy available) [ 7.261381] usb 1-2: New USB device found, idVendor=0781, idProduct=5567 [ 7.268067] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.275310] usb 1-2: Product: Cruzer Blade [ 7.279395] usb 1-2: Manufacturer: SanDisk [ 7.283596] usb 1-2: SerialNumber: 4C530000130118211511 [ 7.296368] usb-storage 1-2:1.0: USB Mass Storage device detected [ 7.308838] scsi host2: usb-storage 1-2:1.0 [ 7.330831] usbcore: registered new interface driver uas [ 7.565107] i2c-gpio i2c-gpio: using pins 41 (SDA) and 42 (SCL) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 8.311838] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6 [ 8.322403] sd 2:0:0:0: [sdb] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB) [ 8.331668] sd 2:0:0:0: [sdb] Write Protect is off [ 8.337835] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.375193] sdb: sdb1 [ 8.382691] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 13.107681] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 13.170969] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...[ 16.941596] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0 done. [ 17.000885] random: nonblocking pool is initialized [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 18.615854] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.29.2 rootfs: clean, 14013/262144 files, 149005/1048576 blocks done. [ 19.027368] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.29.2 done. [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:01:c6:76 Sending on LPF/eth0/00:25:31:01:c6:76 Sending on Socket/fallback DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67 [ 29.020124] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.68.9 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.68.9 from 192.168.68.1 bound to 192.168.68.9 -- renewal in 3263 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1260 (syslogd) . ok [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1263 (klogd) . ok [ ok ] Starting NTP server: ntpd. Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Fri May 15 21:05:49 PDT 2020 on ttyS0 Linux debian 4.4.54-oxnas-tld-1 #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017 armv6l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00e00000 00020000 "boot" mtd1: 1ff200000 00020000 "data" root@debian:~# fw_printenv Warning: Bad CRC, using default environment bootargs= bootcmd= bootdelay=2 baudrate=115200 arch=sandbox cpu=sandbox board=sandbox board_name=sandbox stdin=serial,cros-ec-keyb,usbkbd stdout=serial,vidconsole stderr=serial,vidconsole ethaddr=00:00:11:22:33:44 eth1addr=00:00:11:22:33:45 eth3addr=00:00:11:22:33:46 eth5addr=00:00:11:22:33:47 ipaddr=1.2.3.4 host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi boot_net_pci_enum=pci enum boot_net_usb_start=usb start usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi boot_prefixes=/ /boot/ boot_scripts=boot.scr.uimg boot.scr boot_script_dhcp=boot.scr.uimg boot_targets=host1 host0 boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done bootcmd_host1=setenv devnum 1; run host_boot bootcmd_host0=setenv devnum 0; run host_boot distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done bootm_size=0x10000000 kernel_addr_r=0x1000000 fdt_addr_r=0xc00000 ramdisk_addr_r=0x2000000 scriptaddr=0x1000 pxefile_addr_r=0x2000 root@debian:~#
* And, is it possible to modify the partition size of NAND?
I try Pogo v4. It was possible.
Edited 1 time(s). Last edit at 05/15/2020 11:18PM by Kang Jinsu.
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 16, 2020 02:00AM |
Admin Registered: 13 years ago Posts: 19,102 |
Kang Jinsu,
Looks quite good! NAND chip is fine.
and,
All checked out so far.
The CRC error is expected, since you have replaced NAND.
Don't do that. The new u-boot is expecting the current layout.
=====
OK. You can flash new u-boot. Follow the instruction here:
https://forum.doozan.com/read.php?3,16017
Do it while in Debian. And then post the log of what you did here. I'll doublecheck to see anything is out of ordinary before you reboot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Looks quite good! NAND chip is fine.
[ 6.565527] 2 cmdlinepart partitions found on MTD device 41000000.nand [ 6.572055] Creating 2 MTD partitions on "41000000.nand": [ 6.577433] 0x000000000000-0x000000e00000 : "boot" [ 6.600788] 0x000000e00000-0x000200000000 : "data"
and,
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00e00000 00020000 "boot" mtd1: 1ff200000 00020000 "data"
All checked out so far.
Warning: Bad CRC, using default environment
The CRC error is expected, since you have replaced NAND.
Quote
* And, is it possible to modify the partition size of NAND?
I try Pogo v4. It was possible.
Don't do that. The new u-boot is expecting the current layout.
=====
OK. You can flash new u-boot. Follow the instruction here:
https://forum.doozan.com/read.php?3,16017
Do it while in Debian. And then post the log of what you did here. I'll doublecheck to see anything is out of ordinary before you reboot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Hello, help to fix my device... [Akitio MyCloud Mini] May 16, 2020 02:27AM |
Registered: 4 years ago Posts: 49 |
Here serial console logs.
Edited 1 time(s). Last edit at 05/16/2020 02:27AM by Kang Jinsu.
root@debian:~# ls . .. .bash_history .bashrc .config .nano .profile .ssh root@debian:~# ls / . bin dev home lost+found mnt proc run srv tmp var .. boot etc lib media opt root sbin sys usr root@debian:~# ls /tmp . .. root@debian:~# cd /tmp root@debian:/tmp# wget ftp://admin:**********@192.168.68.1/HDD1/My-Station/Network%20Trashes%20Folder/uboot.2015.10-tld-2.ox820.bodhi.tar --2020-05-16 00:19:46-- ftp://admin:*password*@192.168.68.1/HDD1/My-Station/Network%20Trashes%20Folder/uboot.2015.10-tld-2.ox820.bodhi.tar => 'uboot.2015.10-tld-2.ox820.bodhi.tar' Connecting to 192.168.68.1:21... connected. Logging in as admin ... Logged in! ==> SYST ... done. ==> PWD ... done. ==> TYPE I ... done. ==> CWD (1) /HDD1/My-Station/Network Trashes Folder ... done. ==> SIZE uboot.2015.10-tld-2.ox820.bodhi.tar ... 798720 ==> PASV ... done. ==> RETR uboot.2015.10-tld-2.ox820.bodhi.tar ... done. Length: 798720 (780K) (unauthoritative) uboot.2015.10-tld-2 100%[===================>] 780.00K 2.06MB/s in 0.4s 2020-05-16 00:19:46 (2.06 MB/s) - 'uboot.2015.10-tld-2.ox820.bodhi.tar' saved [798720] root@debian:/tmp# tar -xvf uboot.2015.10-tld-2.ox820.bodhi.tar uboot.2015.10-tld-2.ox820.mtd0.img uboot.spl.2013.10.ox820.850mhz.mtd0.img uboot.2015.10-tld-2.ox820.environment uboot.2015.10-tld-2.ox820.environment.img root@debian:/tmp# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors # pogoplug pro /dev/mtd0 0x00100000 0x20000 0x20000 root@debian:/tmp# blparam -bash: blparam: command not found root@debian:/tmp# fw_printenv Warning: Bad CRC, using default environment bootargs= bootcmd= bootdelay=2 baudrate=115200 arch=sandbox cpu=sandbox board=sandbox board_name=sandbox stdin=serial,cros-ec-keyb,usbkbd stdout=serial,vidconsole stderr=serial,vidconsole ethaddr=00:00:11:22:33:44 eth1addr=00:00:11:22:33:45 eth3addr=00:00:11:22:33:46 eth5addr=00:00:11:22:33:47 ipaddr=1.2.3.4 host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi boot_net_pci_enum=pci enum boot_net_usb_start=usb start usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi boot_prefixes=/ /boot/ boot_scripts=boot.scr.uimg boot.scr boot_script_dhcp=boot.scr.uimg boot_targets=host1 host0 boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done bootcmd_host1=setenv devnum 1; run host_boot bootcmd_host0=setenv devnum 0; run host_boot distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done bootm_size=0x10000000 kernel_addr_r=0x1000000 fdt_addr_r=0xc00000 ramdisk_addr_r=0x2000000 scriptaddr=0x1000 pxefile_addr_r=0x2000 root@debian:/tmp# dmesg | grep -i 'bad' [ 1.263347] Scanning device for bad blocks root@debian:/tmp# flash_erase /dev/mtd0 0x0 6 Erasing 128 Kibyte @ 7f563f5c00000064 -- 6 % complete root@debian:/tmp# nandwrite /dev/mtd0 uboot.spl.2013.10.ox820.850mhz.mtd0.img Writing data to block 0 at offset 0x0 root@debian:/tmp# nandwrite -s 262144 /dev/mtd0 uboot.2015.10-tld-2.ox820.mtd0.img Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 Writing data to block 4 at offset 0x80000 Writing data to block 5 at offset 0xa0000 root@debian:/tmp# flash_erase /dev/mtd0 0x100000 1 Erasing 128 Kibyte @ 7f629f5c00000064 -- 9 % complete root@debian:/tmp# nandwrite -s 1048576 /dev/mtd0 uboot.2015.10-tld-2.ox820.environment.img Writing data to block 8 at offset 0x100000 root@debian:/tmp# fw_printenv [11826.540848] __nand_correct_data: uncorrectable ECC error [11826.546214] __nand_correct_data: uncorrectable ECC error [11826.551508] __nand_correct_data: uncorrectable ECC error [11826.556830] __nand_correct_data: uncorrectable ECC error [11826.562375] __nand_correct_data: uncorrectable ECC error [11826.567726] __nand_correct_data: uncorrectable ECC error [11826.573194] __nand_correct_data: uncorrectable ECC error [11826.578752] __nand_correct_data: uncorrectable ECC error [11826.584099] __nand_correct_data: uncorrectable ECC error [11826.589570] __nand_correct_data: uncorrectable ECC error Warning: Bad CRC, using default environment bootargs= bootcmd= bootdelay=2 baudrate=115200 arch=sandbox cpu=sandbox board=sandbox board_name=sandbox stdin=serial,cros-ec-keyb,usbkbd stdout=serial,vidconsole stderr=serial,vidconsole ethaddr=00:00:11:22:33:44 eth1addr=00:00:11:22:33:45 eth3addr=00:00:11:22:33:46 eth5addr=00:00:11:22:33:47 ipaddr=1.2.3.4 host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi boot_net_pci_enum=pci enum boot_net_usb_start=usb start usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi boot_prefixes=/ /boot/ boot_scripts=boot.scr.uimg boot.scr boot_script_dhcp=boot.scr.uimg boot_targets=host1 host0 boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done bootcmd_host1=setenv devnum 1; run host_boot bootcmd_host0=setenv devnum 0; run host_boot distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done bootm_size=0x10000000 kernel_addr_r=0x1000000 fdt_addr_r=0xc00000 ramdisk_addr_r=0x2000000 scriptaddr=0x1000 pxefile_addr_r=0x2000 root@debian:/tmp#
Edited 1 time(s). Last edit at 05/16/2020 02:27AM by Kang Jinsu.
