Forum List Message List New Topic
conoral11
NSA320 - Completely Stock OS 4.70
November 02, 2020 07:04AM
Hi there,

I have a completely stock NSA320 and would like to both upgrade the uboot and install debian to USB.

Where do I start? I've read some forum posts here that everything can be done in the stock OS without using the uart connection. Is this true?

If so how?

Otherwise I'll go ahead in install a UART-USB link.

Hope you can help.
Reply Quote
bodhi
Re: NSA320 - Completely Stock OS 4.70
November 02, 2020 03:28PM
conoral11,

> I have a completely stock NSA320 and would like to
> both upgrade the uboot and install debian to USB.
>
> Where do I start? I've read some forum posts here
> that everything can be done in the stock OS
> without using the uart connection. Is this true?
>

True. But serial console connection would be best to have, in case you run into any problem and need to rescue it. And look at the u-boot installation instruction to see that you should try UART booting with kwboot first, if you have serial console.

From stock OS, you can install both U-Boot and Debian rootfs (Debian rootfs on USB drive, if your HDD already have data on it).

U-Boot:
https://forum.doozan.com/read.php?3,12381

Debian:
https://forum.doozan.com/read.php?2,12096

If you decide to install without serial console connected then before you reboot, you could post the log of the entire session here and I'll double check for you..

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
conoral11
Re: NSA320 - Completely Stock OS 4.70
November 12, 2020 02:53AM
The missing link for me was how to enable the telnet interface, as there wasn't an option in the stock firmware interface to enable it.

Using:

http://NSA320_IP/r41794,/adv,/cgi-bin/remote_help-cgi?type=backdoor

(changing r41794 to what ever your NSA320 puts in the address bar)

Enables the telnet interface, then its just following the instructions in the links above.

Hope that helps.
Reply Quote
mrmazak
Re: NSA320 - Completely Stock OS 4.70
November 12, 2020 05:44AM
Good to know you are getting it working.
I have just last weekend (Nov 7&8) flashed my nsa320 over to buster .

The serial console was easy to setup from an extra raspberry pi I had , so didn't need to buy usb-tty adapter.
Reply Quote
psychokiller
Re: NSA320 - Completely Stock OS 4.70
December 09, 2020 09:15AM
Hi!
I read you have a stock NSA320, but probably you already flashed it with new U-Boot and Debian.
If you haven't flashed it yet I am very interested in a dump of your nand to restore an NSA320 I have with stock firmware.
I will PM you as well hoping you will read both this thread and PMs.
Thanx, Paolo.
Reply Quote
vcheche
Re: NSA320 - Completely Stock OS 4.70
January 05, 2021 06:24AM
@psychokiller

Download this archive, unzip it to a USB stick.
Power off NSA320, connect the stick to it, power on, wait (you can watch via TTL serial if you have it connected).

https://mega.nz/file/Sz5jDKKJ#gm1NdQBVt9WhkRO4q0Cf6RPJdS7Fp537jkv0a6sRz-0

Got this from deep inside of one of the many official ZyXEL ftp locations, downloaded some years ago, it is a recovery stick.
It will restore the NSA320 to one of the original firmware, and you can then update to the latest available.

Not sure about the MAC address restore (if it writes the correct one....), can't remember, haven't used this tool in >2 years now.

Cheers.



Edited 2 time(s). Last edit at 01/05/2021 06:27AM by vcheche.
Reply Quote
bandicoot
Re: NSA320 - Completely Stock OS 4.70
March 08, 2021 07:59AM
Hi there,

I am new on this forum, so if I should not post my issue here, could you tell me where I should post it?

I also would like to upgrade to Debian on my NSA320. But unfortunately I have sort of bricked my NAS in testing all sorts of commands which I thought were only reading, but I must have done something that makes the boot fail.
I had fonz fun plug and entware installed, and I do not exactly know how this was functioning. I assume that entware overruled fonz fun plug. But other than this it was pretty much a stock version 4.7 firmware. Ik have not installed new uboot's or anything. It must have been using the disks as well through a clever kind of of hooking through symbolic links created by the fun_plug.sh hook, but I do not know the details of this process.

I had to reboot the machine recently and it did start to a certain point, because all the led's were on, other than that it appeared dead, the disks did not spin-up and I could not connect to it.

As I am also playing around with arduino I had a pl2303 lying around, so I hooked it up to the serial pins of the NSA320 and used putty to have a look at the boot process.

The thing that looks bad the most is this: 
reading NAND page at offset 0x4640000 failed
 10485760 bytes read: ERROR
## Booting image at 02000000 ...
Bad Magic Number


Here is the (complete) output including a few commands somebody will ask me for, so I am anticipating on that: 
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Mar 23 2011 - 16:09:39) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFEE0

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
//---  stateButtonBit = 3, recovery ---//
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0, egiga1 [PRIME]
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x4640000, size 0xa00000

reading NAND page at offset 0x4640000 failed
 10485760 bytes read: ERROR
## Booting image at 02000000 ...
Bad Magic Number


NSA320>> version
U-Boot 1.1.4 (Mar 23 2011 - 16:09:39) Marvell version: 3.4.19

NSA320>> sp

Bus: 0 Device: 0 Func: 0 Vendor ID: 11ab Device ID: 6281
-------------------------------------------------------------------
Class: Memory controller
PCI_BAR0 (Mem-64bit) base: 0f1000000    size: 1048576 bytes
PCI_BAR1 (Mem-64bit) base: 000000000            size: 536870912 bytes

NSA320>> sg
PHY 0 :
---------
Auto negotiation: Enabled
Speed: 1000 Mbps
Duplex: Half
Link: down

PHY 1 :
---------
Auto negotiation: Enabled
Speed: Uknown
Duplex: Full
Link: up

NSA320>> dclk
TCLK 200Mhz, SYSCLK 400Mhz (UART baudrate 115200)

NSA320>> printinfo
kernel_addr_1=0xc80000
kernel_mtd_1=5
sysimg_mtd_1=6
kernel_addr_2=0x4640000
kernel_mtd_2=7
sysimg_mtd_2=8
fwversion_1=V4.70(AFO.1)
revision_1=41794
modelid_1=DD01
core_checksum_1=678f3d0f5000c5e00235856a6c186057
zld_checksum_1=15b8a3bfb65e6ad60f55fc7f23e76171
romfile_checksum_1=98E5
img_checksum_1=010c65c574d9a45f2a09f451a92c1611
fwversion_2=V4.70(AFO.3)
revision_2=49435
modelid_2=DD01
core_checksum_2=81e0d1021bdce8c0cca99e237e21dc84
zld_checksum_2=6b7d0e43486e5cd6bec65016032ce081
romfile_checksum_2=B65B
img_checksum_2=a1e743a41560dc3edcb22b943b199ec2
next_bootfrom=2
curr_bootfrom=2

Info size: 591/131068 bytes

NSA320>> ide reset

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: SAMSUNG HD501LJ                          Firm: CR100-10 Ser#: S0MUJ1MPXXXXXX
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
[0 1 0]: Enable DMA mode (6)
  Device 1 @ 0 1:
Model: ST4000DM005-2DP166                       Firm: 0001     Ser#:             XXXXXXXX
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1718295.8 MB = 1678.0 GB (-775897424 x 512)


NSA320>> printenv
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000
bootdelay=2
baudrate=115200
loads_echo=0
eth1addr=00:19:CB:00:51:82
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=DD01
PRODUCT_NAME=NSA-320
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=ZyXEL Communications Corp.
run_diag=yes
ethaddr=B0:B2:DC:F0:FF:12
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
ethprime=egiga1
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
disaMvPnp=no
ethmtu=1500
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
hddPowerCtrl=no
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
enaAutoRecovery=yes
kernel_addr=0x4640000
pcieTune=no
ethact=egiga1

Environment size: 1558/131068 bytes

I have seen on this forum printenv output's of supposedly stock NSA320's with different values for kernel_addr, in one it was 0x4640000 and in another it was something like 0x8000000 (I can not remember the amount of zero's). So I do not know if this is possibly causing my issue.

Before I continue with trying to get Debian installed I would like to have this problem fixed, or is this not important, as I can get to the uboot prompt?

Could somebody point me in the right direction of what could be wrong with my NSA320 boot/nand's?

Cheers



Edited 6 time(s). Last edit at 03/08/2021 11:04AM by bandicoot.
Reply Quote
bodhi
Re: NSA320 - Completely Stock OS 4.70
March 09, 2021 02:19AM
bandicoot,

> Before I continue with trying to get Debian
> installed I would like to have this problem fixed,
> or is this not important, as I can get to the
> uboot prompt?

Correct. Since you still can boot to the u-boot prompt, and have serial console, there is no need to deal with stock error.

There 2 ways to boot into Debian from serial console. Both require you to create the Debian rootfs on USB first.

https://forum.doozan.com/read.php?2,12096

1. Create the rootfs on USB using Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2. Scroll down to the section:

Quote

Updated 25 Aug 2019:

Basic Debian buster Kirkwood rootfs for most Kirwood plugs:

- tarball size: 209M
- install size: 536M
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, sysvinit-utils, u-boot-tools, and mtd-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root

Download at Dropbox:

Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2

2. Method 1: You can boot directly from u-boot console using this instruction:

https://forum.doozan.com/read.php?2,102054,105374#msg-105374

This apprach requires you to do Step 4 (Create uImage with embedded DTB) on the rootfs instruction.

OR

3. Method 2: You can boot using kwboot to load the new u-boot image over UART:

https://forum.doozan.com/read.php?3,51739,51919#msg-51919

This apprach requires you to do skip Step 4 (Create uImage with embedded DTB) on the rootfs instruction.

After the loading is successful, you can boot straight into the USB Debian rootfs with boot command: 

boot


=======

Between method 1 and 2, I would do method 2 (if you have another Linux box where you run serial console). Because if you can use kwboot loading the new u-boot over UART and run it, then you have a rescue mechanism for any problem now or future.

And also it does not require entering new u-boot envs (the new u-boot image internal envs are good enough to boot the USB rootfs).

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
bandicoot
Re: NSA320 - Completely Stock OS 4.70
March 09, 2021 03:57PM
Hi Bodhi,

Thanks so much for your help! I will give the instructions a go tomorrow. I have a fedora desktop machine, would for example the mkimage work correctly in fedora to create a kernelimage for the NSA320, or do I really need a Debian system for that as well?

Cheers
Reply Quote
bodhi
Re: NSA320 - Completely Stock OS 4.70
March 09, 2021 05:10PM
bandicoot,

> would for example the mkimage
> work correctly in fedora to create a kernelimage
> for the NSA320, or do I really need a Debian
> system for that as well?

Fedora is fine to create the USB rootfs on it.

The process of creating rootfs does not involve installing any specific kernel (it is already in the rootfs). So any Linux box would suffice.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
bandicoot
Re: NSA320 - Completely Stock OS 4.70
March 11, 2021 11:15AM
Hi Bodhi,

The powersupply of my fedora desktop is dead, so I ended up creating a fedora usb stick to boot my laptop. I did everything you instructed and also ran in to long lines in stock uboot and had to use the second set you gave to Paul in the link you gave me for the booting instructions.

But now I ran into another issue on my NSA320. It appears the USB system is dead. It can not find the USB-stick I created the rootfs on (ext3).

I started looking for USB commands and tried them: 

        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Mar 23 2011 - 16:09:39) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFEE0

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
//---  stateButtonBit = 3, recovery ---//
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0, egiga1 [PRIME]
Hit any key to stop autoboot:  0
NSA320>> usb reset
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
NSA320>> usb start
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
NSA320>> usb stop
stopping USB..
NSA320>> usb start
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
NSA320>> usb reset
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
NSA320>> usb reset
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
NSA320>> usb start
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
NSA320>>

I am assuming I should see with a 'USB reset' that I inserted the usb-stick like so (found that in another post): 
Marvell>> boot
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found

Is the USB system of my NSA320 now dead? Or is it something with the bios/rom or whereever the usb-drivers for uboot live?

If it is dead, what other options can you think of to revive my NSA320, like for example just use sata and a disk. And if this is an option, would the existing sata disk (500 GB ext3) with data on it be an option to just merge the rootfs into it, only /tmp is clashing with rootfs.

Cheers



Edited 1 time(s). Last edit at 03/11/2021 11:31AM by bandicoot.
Reply Quote
bandicoot
Re: NSA320 - Completely Stock OS 4.70
March 11, 2021 04:14PM
Hi Bodhi,

I already managed to get it going on a hd replacing usb by ide in the boot sequence: 
setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
setenv load_uimage 'ext2load ide 0:1 0x800000 /boot/uImage'
setenv load_uinitrd 'ext2load ide 0:1 0x2100000 /boot/uInitrd'
setenv ide_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000'
setenv ide_bootcmd 'run ide_set_bootargs; run ide_boot'
setenv bootcmd 'ide reset; ide start; run ide_bootcmd; ide stop; reset'

I also did the update and upgrade. So it is working now.

You wrote to run: 
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-5.2.9-kirkwood-tld-1 -d initrd.img-5.2.9-kirkwood-tld-1 uInitrd
If I see: 
update-initramfs: Generating /boot/initrd.img-5.2.9-kirkwood-tld-1
in the update/upgrade.

But the original thing to do was for my case: 
cp -a zImage-5.2.9-kirkwood-tld-1  zImage.fdt
cat dts/kirkwood-goflexnet.dtb  >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-kirkwood-tld-1 -d zImage.fdt  uImage

Is the first mkimage the correct one then? Or should I run the second sequence again?

Cheers
Reply Quote
bodhi
Re: NSA320 - Completely Stock OS 4.70
March 11, 2021 05:09PM
bandicoot,


> Is the first mkimage the correct one then? Or
> should I run the second sequence again?

No, they are both correct for different purpose.

After you installed everything and do apt-get upgrade and see 

update-initramfs: Generating /boot/initrd.img-5.2.9-kirkwood-tld-1

Then you need to regenerate uInitrd with 

mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-5.2.9-kirkwood-tld-1 -d initrd.img-5.2.9-kirkwood-tld-1 uInitrd


The commands done during rootf creation was to create uImage (note the DTB for your box is kirkwood-nsa320.dtb): 

cp -a zImage-5.2.9-kirkwood-tld-1  zImage.fdt
cat dts/kirkwood-nsa320.dtb  >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-kirkwood-tld-1 -d zImage.fdt  uImage
So you can see that this uImage creation does not have anything to do with the initramfs.

======

At this point, if you want to go further, you should upgrade u-boot to the latest. But it is not necessary to run the new u-boot with the latest Linux kernel. You could stay with stock u-boot if you want to.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
March 28, 2025 08:41AM
What to do if I have deleted everything?

Even connecting via USB-TTY adapter does not cause any reaction.

Only the power LED lights up, the fan works.

No reaction.

I have probably deleted the entire contents of the NAND memory
Is it still possible to save my NSA320?
Reply Quote
bodhi
Re: NSA320 - Completely Stock OS 4.70
March 28, 2025 12:52PM
petecom,

The 1st thing in recovering a bricked box is: try to run kwboot to load the new u-boot. See this post for how to:
https://forum.doozan.com/read.php?3,51739,51919#msg-51919

Use the u-boot image uboot.2017.07-tld-1.nsa320.mtd0.kwb from here:
https://forum.doozan.com/read.php?3,12381
(the tarball tar -xf uboot.2017.07-tld-1.nsa320.bodhi.tar)

If you don't see response, check you UART connection: TX-RX RX-TX GND-GND.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
March 28, 2025 02:59PM
A few basic questions
1. I bought another M2 drive for my computer and installed KUBUNTU 24.10 on it
Info:
KDE Plasma Version: 6.1.5
KDE Frameworks Version: 6.6.0
Qt Version: 6.6.2
Kernel Version: 6.11.0-21-generic (64-bit)
Graphics Platform: Wayland
Processors: 24 × 12th Gen Intel® Core™ i9-12900KS
Memory: 31.1 GiB of RAM
Graphics Processor: NVIDIA GeForce RTX 4070
Manufacturer: ASRock
Product Name: Z790 Pro RS/D4

I connected the CP2102 USB to UART Bridge Controller to the USB HUB
I have connected it to the ZYXEL NAS320S board, the pins are as you wrote
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
March 28, 2025 03:34PM
OK.
01. Type 
sudo kwboot  -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb  -p

kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...|


How long to wait. Will it end? Should I stop it?

Och no!

/Failed to send message pattern: Input/output error



Edited 1 time(s). Last edit at 03/28/2025 03:37PM by petecom.
Reply Quote
bodhi
Re: NSA320 - Completely Stock OS 4.70
March 28, 2025 03:37PM
Do you have the NSA320 or NSA320S? They are 2 different boxes.

Quote
https://forum.doozan.com/read.php?3,12381
tar -xf uboot.2017.07-tld-1.dockstar.bodhi.tar
tar -xf uboot.2017.07-tld-1.goflexhome.bodhi.tar
tar -xf uboot.2017.07-tld-1.goflexnet.bodhi.tar
tar -xf uboot.2017.07-tld-1.iconnect.bodhi.tar
tar -xf uboot.2017.07-tld-1.netgear_ms2110.bodhi.tar
tar -xf uboot.2017.07-tld-1.pogo_e02.bodhi.tar
tar -xf uboot.2017.07-tld-1.pogo_v4.bodhi.tar
tar -xf uboot.2017.07-tld-2.sheevaplug.bodhi.tar
tar -xf uboot.2017.07-tld-1.nsa320.bodhi.tar
tar -xf uboot.2017.07-tld-1.nsa325.bodhi.tar
tar -xf uboot.2017.07-tld-1.nsa310s.bodhi.tar
tar -xf uboot.2017.07-tld-1.nsa310.bodhi.tar

Use uboot.2017.07-tld-1.nsa310s.bodhi.tar if you have the NSA320S.
Use uboot.2017.07-tld-1.nsa320.bodhi.tar if you have the NSA320.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
March 28, 2025 04:20PM
Zyxel NSA320S 

sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p


USB-UART flashing extra blue led

and

kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...|

How long to wait?

What's next?



Edited 2 time(s). Last edit at 03/28/2025 04:24PM by petecom.
Reply Quote
Attachments:
open | download - HangUp_01.png (158.5 KB)
petecom
Re: NSA320 - Completely Stock OS 4.70
March 29, 2025 06:51AM
Zyxel NSA320S

Step 1:
Connect the CP2102 USB to UART Bridge Controller to the USB HUB using ONLY three pins
RX to TX
TX to RX
GND to GND
Step 2:
Launch the console on your computer and go to the location where you saved the files. 
cd Downloads/U-boot/NSA320S
Type and execute the command: 
sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p
The following lines will be displayed: 
kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...-
NOTE: In my case the power button didn't work and I had to connect the power supply to the board, then disconnect and reconnect it. Only then did it start sending data.
Here's the result: 
Sending boot image header (512 bytes)...
 25 % [....                                                                  ]
Done
Sending boot image data (509836 bytes)...
  0 % [......................................................................]
  1 % [......................................................................]
  3 % [......................................................................]
  5 % [......................................................................]
  7 % [......................................................................]
  8 % [......................................................................]
 10 % [......................................................................]
 12 % [......................................................................]
 14 % [......................................................................]
 15 % [......................................................................]
 17 % [......................................................................]
 19 % [......................................................................]
 21 % [......................................................................]
 22 % [......................................................................]
 24 % [......................................................................]
 26 % [......................................................................]
 28 % [......................................................................]
 29 % [......................................................................]
 31 % [......................................................................]
 33 % [......................................................................]
 35 % [......................................................................]
 36 % [......................................................................]
 38 % [......................................................................]
 40 % [......................................................................]
 42 % [......................................................................]
 43 % [......................................................................]
 45 % [......................................................................]
 47 % [......................................................................]
 49 % [......................................................................]
 50 % [......................................................................]
 52 % [......................................................................]
 54 % [......................................................................]
 56 % [......................................................................]
 58 % [......................................................................]
 59 % [......................................................................]
 61 % [......................................................................]
 63 % [......................................................................]
 65 % [......................................................................]
 66 % [......................................................................]
 68 % [......................................................................]
 70 % [......................................................................]
 72 % [......................................................................]
 73 % [......................................................................]
 75 % [......................................................................]
 77 % [......................................................................]
 79 % [......................................................................]
 80 % [......................................................................]
 82 % [......................................................................]
 84 % [......................................................................]
 86 % [......................................................................]
 87 % [......................................................................]
 89 % [......................................................................]
 91 % [......................................................................]
 93 % [......................................................................]
 94 % [......................................................................]
 96 % [......................................................................]
 98 % [................................................................      ]
Done
Finishing transfer
[Type Ctrl-\ + c to quit]
Reply Quote
bodhi
Re: NSA320 - Completely Stock OS 4.70
March 29, 2025 02:00PM 
Finishing transfer
[Type Ctrl-\ + c to quit]

> NOTE: In my case the power button didn't work and
> I had to connect the power supply to the board,
> then disconnect and reconnect it. Only then did it
> start sending data.

That's a lot progress! And it might have lost the handshake after the loading was complete.

Try running the newer kwboot:

https://forum.doozan.com/read.php?3,27280

If the Linux host is Intel x86 64 bit, use

Quote

2. I've attached the 2025.01-rc1 kwboot static binary (x86-64) to this post:
kwboot_2025.01-rc1_x86-64.tar.bz2
(kwboot version u-boot version 2025.01-rc1-ge61ea9f2e5d2-dirty)
sha256:
a63e93d76bafa01605dbed5e0d786e689187d3a85b8bcda153847406580e1f8d

After downloaded, you can extract and rename kwboot_2025.01-rc1_x86-64 to just kwboot.

Download the kwboot binary to your Linux host. And execute it dirrectly from the directory where it is (./kwboot): 

sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
March 30, 2025 05:02AM
For version 2025.01-rc1-ge61ea9f2e5d2-dirty not work
piotr@PC-Kubuntu-01:~/Pobrane/U-boot/NSA320$ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p
kwboot version 2025.01-rc1-ge61ea9f2e5d2-dirty
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target.../
-
\^C

For version 2024.01
piotr@PC-Kubuntu-01:~/Pobrane/U-boot/NSA320$ sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p
kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...-
Sending boot image header (512 bytes)...
25 % [.... ]
Done
Sending boot image data (509836 bytes)...
0 % [......................................................................]
1 % [......................................................................]
3 % [......................................................................]
5 % [......................................................................]
7 % [......................................................................]
8 % [......................................................................]
10 % [......................................................................]
12 % [......................................................................]
14 % [......................................................................]
15 % [......................................................................]
17 % [......................................................................]
19 % [......................................................................]
21 % [......................................................................]
22 % [......................................................................]
24 % [......................................................................]
26 % [......................................................................]
28 % [......................................................................]
29 % [......................................................................]
31 % [......................................................................]
33 % [......................................................................]
35 % [......................................................................]
36 % [......................................................................]
38 % [......................................................................]
40 % [......................................................................]
42 % [......................................................................]
43 % [......................................................................]
45 % [......................................................................]
47 % [......................................................................]
49 % [......................................................................]
50 % [......................................................................]
52 % [......................................................................]
54 % [......................................................................]
56 % [......................................................................]
58 % [......................................................................]
59 % [......................................................................]
61 % [......................................................................]
63 % [......................................................................]
65 % [......................................................................]
66 % [......................................................................]
68 % [......................................................................]
70 % [......................................................................]
72 % [......................................................................]
73 % [......................................................................]
75 % [......................................................................]
77 % [......................................................................]
79 % [......................................................................]
80 % [......................................................................]
82 % [......................................................................]
84 % [......................................................................]
86 % [......................................................................]
87 % [......................................................................]
89 % [......................................................................]
91 % [......................................................................]
93 % [......................................................................]
94 % [......................................................................]
96 % [......................................................................]
98 % [................................................................ ]
Done
Finishing transfer
[Type Ctrl-\ + c to quit]


U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700)
ZyXEL NSA310S/320S 1/2-Bay Power Media Server

SoC: Kirkwood 88F6702_A1
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot: 0
NSA3x0S>

next step please
Reply Quote
Attachments:
open | download - 20250330_120418.jpg (700.8 KB)
bodhi
Re: NSA320 - Completely Stock OS 4.70
March 30, 2025 01:44PM
petecom,

> U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06
> -0700)
> ZyXEL NSA310S/320S 1/2-Bay Power Media Server
>
> SoC: Kirkwood 88F6702_A1
> DRAM: 256 MiB
> WARNING: Caches not enabled
> NAND: 128 MiB
> *** Warning - bad CRC, using default environment
>
> In: serial
> Out: serial
> Err: serial
> Net: egiga0
> MV88E1318 PHY initialized on egiga0
> Hit any key to stop autoboot: 0
> NSA3x0S>

Congrats! you have unbricked this box.

Next step is booting to Debian on USB. Follow the instruction in this section to create a USB rootfs.

https://forum.doozan.com/read.php?2,12096

Quote

Updated 01 Nov 2023:

Basic Debian bookworm Kirkwood rootfs for most Kirwood plugs

Since you are booting with new u-boot 2017.07, don't do Step 4.

Quote

4. (Stock u-boot only)

Create the USB rootfs on other Linux box, and bring it to the NSA320S. Insert the USB and run kwboot, power up like you did. Let it boot automatically into Debian. And then post the entire serial console log here.

Please do not post picture. Copy and paste the text from the Linux terminal and post here (or save it in a text file and attach here). You can also use pastebin.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
April 27, 2025 05:46AM
Which Debian to choose for USB to NSA320S

A regular distribution or is there a dedicated one?
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
April 27, 2025 05:51AM
Can I use a variant of ubuntu or maybe OpenSuse Tumbleweed?
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
April 27, 2025 08:03AM 
NSA3x0S> printenv
arcNumber=4931
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-nsa310s.dtb
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_ready_retry=15

Environment size: 3009/131068 bytes

What should I do next to make the NSA320S boot from the USB port?

Only the SYS LED lights up green
and there is no reaction
Reply Quote
petecom
Re: NSA320 - Completely Stock OS 4.70
April 27, 2025 12:54PM
Help! 
NAND read: device 0 offset 0xa00000, size 0x7600000
 123731968 bytes read: OK
Wrong Image Format for bootm command
Error occured, error code = 112
ERROR: can't get kernel image!
NSA3x0S>

What should I do?
Reply Quote
bodhi
Re: NSA320 - Completely Stock OS 4.70
April 27, 2025 03:06PM
petecom,

I've posted above what you should do next

https://forum.doozan.com/read.php?2,110409,139484#msg-139484

Quote

Congrats! you have unbricked this box.

Next step is booting to Debian on USB. Follow the instruction in this section to create a USB rootfs. The Debian system is Debian-6.5.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2.

https://forum.doozan.com/read.php?2,12096

Quote

Quote

Updated 01 Nov 2023:

Basic Debian bookworm Kirkwood rootfs for most Kirwood plugs

Since you are booting with new u-boot 2017.07, don't do Step 4.

Quote


Create the USB rootfs on other Linux box, and bring it to the NSA320S. Insert the USB and run kwboot, power up like you did. Let it boot automatically into Debian. And then post the entire serial console log here.

Please do not post picture. Copy and paste the text from the Linux terminal and post here (or save it in a text file and attach here). You can also use pastebin.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
Newer Topic Older Topic
Author:

Your Email:


Subject:
Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: