Kernel crash during boot 5.4.101-oxnas-tld-1 May 04, 2021 03:44AM |
Registered: 2 years ago Posts: 4 |
Please append a correct "root =" boot option; here are the available partitions:
U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) Boot device: SATA Attempting to set PLLA to 800 MHz ... plla_ctrl0 : 0000030a plla_ctrl1 : 00400000 plla_ctrl2 : 007f0068 plla_ctrl3 : 00000193 PLLA Set Bus 0: OK Device 0: reading bootargs.bin reading u-boot.img reading u-boot.img U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS DRAM: 128 MiB IDE: Bus 0: OK Device 0: Model: ST98823AS Firm: 3.04 Ser#: 5PK0ZQQV Type: Hard Disk Supports 48-bit addressing Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) NAND: 128 MiB reading u-boot.env In: serial Out: serial Err: serial Net: mii0 ## Error: "safeboot" not defined Hit any key to stop autoboot: 0 5502688 bytes read in 1193 ms (4.4 MiB/s) 8618 bytes read in 24 ms (350.6 KiB/s) magic: 0xd00dfeed totalsize: 0x21aa (8618) off_dt_struct: 0x38 off_dt_strings: 0x1e80 off_mem_rsvmap: 0x28 version: 17 last_comp_version: 16 boot_cpuid_phys: 0x0 size_dt_strings: 0x32a size_dt_struct: 0x1e48 number mem_rsv: 0x0 ## Booting kernel from Legacy Image at 60000000 ... Image Name: Linux-5.4.101-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5502624 Bytes = 5.2 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 61000000 Booting using the fdt blob at 0x61000000 Loading Kernel Image ... OK Loading Device Tree to 67e26000, end 67e2b1a9 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.4.101-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 SMP PREEMPT Sat Feb 27 20:19:53 PST 2021 [ 0.000000][ T0] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Pogoplug V3 Classic [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] percpu: Embedded 15 pages/cpu s30508 r8192 d22740 u61440 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000][ T0] Kernel command line: earlyprintk [ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 116968K/131072K available (8192K kernel code, 232K rwdata, 2088K rodata, 1024K init, 260K bss, 14104K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_random_seq_create+0x78/0x12c with crng_init=0 [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16 [ 0.000020][ T0] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.008780][ T0] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.020119][ T0] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.026887][ T0] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.036047][ T0] GIC: PPI13 is secure or misconfigured [ 0.041464][ T0] GIC: PPI13 is secure or misconfigured [ 0.047047][ T0] Console: colour dummy device 80x30 [ 0.052218][ T0] printk: console [tty0] enabled [ 0.057000][ T0] printk: bootconsole [earlycon0] disabled [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.4.101-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 SMP PREEMPT Sat Feb 27 20:19:53 PST 2021 [ 0.000000][ T0] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Pogoplug V3 Classic [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] percpu: Embedded 15 pages/cpu s30508 r8192 d22740 u61440 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000][ T0] Kernel command line: earlyprintk [ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 116968K/131072K available (8192K kernel code, 232K rwdata, 2088K rodata, 1024K init, 260K bss, 14104K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_random_seq_create+0x78/0x12c with crng_init=0 [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16 [ 0.000020][ T0] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.008780][ T0] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.020119][ T0] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.026887][ T0] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.036047][ T0] GIC: PPI13 is secure or misconfigured [ 0.041464][ T0] GIC: PPI13 is secure or misconfigured [ 0.047047][ T0] Console: colour dummy device 80x30 [ 0.052218][ T0] printk: console [tty0] enabled [ 0.057000][ T0] printk: bootconsole [earlycon0] disabled [ 0.062725][ T0] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440) [ 0.111585][ T0] pid_max: default: 32768 minimum: 301 [ 0.112043][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.112097][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.112299][ T0] *** VALIDATE tmpfs *** [ 0.113349][ T0] *** VALIDATE proc *** [ 0.113635][ T0] *** VALIDATE cgroup1 *** [ 0.113679][ T0] *** VALIDATE cgroup2 *** [ 0.113830][ T0] CPU: Testing write buffer coherency: ok [ 0.116039][ T1] Setting up static identity map for 0x60100000 - 0x60100038 [ 0.116367][ T1] rcu: Hierarchical SRCU implementation. [ 0.117283][ T1] smp: Bringing up secondary CPUs ... [ 0.118456][ T0] GIC: PPI13 is secure or misconfigured [ 0.171868][ T1] smp: Brought up 1 node, 2 CPUs [ 0.171937][ T1] SMP: Total of 2 processors activated (638.97 BogoMIPS). [ 0.172951][ T1] devtmpfs: initialized [ 0.178439][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.178539][ T1] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.178726][ T1] prandom: seed boundary self test passed [ 0.183319][ T1] prandom: 100 self tests passed [ 0.183352][ T1] pinctrl core: initialized pinctrl subsystem [ 0.184862][ T1] NET: Registered protocol family 16 [ 0.186703][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.189473][ T1] cpuidle: using governor ladder [ 0.189596][ T1] cpuidle: using governor menu [ 7.183969][ T1] vgaarb: loaded [ 7.184847][ T1] SCSI subsystem initialized [ 7.185664][ T1] usbcore: registered new interface driver usbfs [ 7.185804][ T1] usbcore: registered new interface driver hub [ 7.185914][ T1] usbcore: registered new device driver usb [ 7.186224][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.186270][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.186342][ T1] PTP clock support registered [ 7.187878][ T1] clocksource: Switched to clocksource oxnas_rps_clocksource_timer [ 7.187985][ T1] *** VALIDATE bpf *** [ 7.188474][ T1] *** VALIDATE ramfs *** [ 7.208192][ T1] NET: Registered protocol family 2 [ 7.209323][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 7.209436][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 7.209515][ T1] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 7.209584][ T1] TCP: Hash tables configured (established 1024 bind 1024) [ 7.209832][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 7.209927][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 7.210278][ T1] NET: Registered protocol family 1 [ 7.211420][ T1] RPC: Registered named UNIX socket transport module. [ 7.211486][ T1] RPC: Registered udp transport module. [ 7.211522][ T1] RPC: Registered tcp transport module. [ 7.211558][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.211604][ T1] PCI: CLS 0 bytes, default 32 [ 7.213276][ T1] Initialise system trusted keyrings [ 7.213386][ T1] Key type blacklist registered [ 7.213777][ T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 7.225996][ T1] zbud: loaded [ 7.231621][ T1] NFS: Registering the id_resolver key type [ 7.231713][ T1] Key type id_resolver registered [ 7.231749][ T1] Key type id_legacy registered [ 7.231800][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 7.231846][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.233103][ T1] fuse: init (API version 7.31) [ 7.233344][ T1] *** VALIDATE fuse *** [ 7.233395][ T1] *** VALIDATE fuse *** [ 7.234270][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 7.234624][ T1] orangefs_init: module version upstream loaded [ 7.292026][ T1] Key type asymmetric registered [ 7.292106][ T1] Asymmetric key parser 'x509' registered [ 7.292221][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 7.294689][ T1] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 7.296445][ T1] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A [ 7.922531][ T1] printk: console [ttyS0] enabled [ 7.942126][ T1] loop: module loaded [ 7.948172][ T1] scsi host0: sata_oxnas [ 7.952924][ T1] ata1: SATA max UDMA/133 irq 57 [ 7.957926][ T75] sata_oxnas: resetting SATA core [ 8.028236][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it [ 8.037626][ T1] ONFI parameter recovery failed, aborting [ 8.043371][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 8.050455][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit [ 8.055595][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 8.063910][ T1] Scanning device for bad blocks [ 8.152568][ T1] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller [ 8.161226][ T1] Creating 2 MTD partitions on "41000000.nand-controller": [ 8.168317][ T1] 0x000000000000-0x000000e00000 : "boot" [ 8.176448][ T1] 0x000000e00000-0x000008000000 : "data" [ 8.185694][ T1] libphy: Fixed MDIO Bus: probed [ 8.190881][ T1] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found [ 8.197757][ T1] oxnas-dwmac 40400000.ethernet: PTP uses main clock [ 8.204346][ T1] oxnas-dwmac 40400000.ethernet: no reset control found [ 8.278343][ T1] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35 [ 8.286028][ T1] oxnas-dwmac 40400000.ethernet: DWMAC1000 [ 8.291834][ T1] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported [ 8.299888][ T1] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported [ 8.307932][ T1] oxnas-dwmac 40400000.ethernet: COE Type 2 [ 8.313676][ T1] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported [ 8.321280][ T1] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported [ 8.328284][ T1] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors [ 8.335772][ T1] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors [ 8.343114][ T1] oxnas-dwmac 40400000.ethernet: Ring mode enabled [ 8.349521][ T1] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 8.368064][ T1] libphy: stmmac: probed [ 8.372193][ T1] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 8.382487][ T1] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL) [ 8.393799][ T1] PPP generic driver version 2.4.2 [ 8.399255][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.406489][ T1] ehci-pci: EHCI PCI platform driver [ 8.467937][ T75] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 8.476241][ T75] ata1.00: ATA-7: ST98823AS, 3.04, max UDMA/133 [ 8.482449][ T75] ata1.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 8.491545][ T75] ata1.00: configured for UDMA/133 [ 8.497159][ T7] scsi 0:0:0:0: Direct-Access ATA ST98823AS 3.04 PQ: 0 ANSI: 5 [ 8.507806][ T54] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) [ 8.516933][ T54] sd 0:0:0:0: [sda] Write Protect is off [ 8.522780][ T54] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.543168][ T54] sda: sda1 sda2 sda3 [ 8.550625][ T54] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.617945][ T1] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 8.624194][ T1] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 8.632852][ T1] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100 [ 8.667932][ T1] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 8.675033][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 8.684067][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.692042][ T1] usb usb1: Product: EHCI Host Controller [ 8.697612][ T1] usb usb1: Manufacturer: Linux 5.4.101-oxnas-tld-1 ehci_hcd [ 8.704865][ T1] usb usb1: SerialNumber: 40200100.ehci [ 8.711326][ T1] hub 1-0:1.0: USB hub found [ 8.715880][ T1] hub 1-0:1.0: 2 ports detected [ 8.721853][ T1] usbcore: registered new interface driver cdc_wdm [ 8.728483][ T1] usbcore: registered new interface driver usb-storage [ 8.735418][ T1] usbcore: registered new interface driver usbserial_generic [ 8.742760][ T1] usbserial: USB Serial support registered for generic [ 8.749941][ T1] mousedev: PS/2 mouse device common for all mice [ 8.756364][ T1] i2c /dev entries driver [ 8.762083][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 8.768504][ T1] usbcore: registered new interface driver usbhid [ 8.774778][ T1] usbhid: USB HID core driver [ 8.780917][ T1] NET: Registered protocol family 10 [ 8.787773][ T1] Segment Routing with IPv6 [ 8.792368][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 8.801221][ T1] NET: Registered protocol family 17 [ 8.806781][ T1] Key type dns_resolver registered [ 8.812431][ T1] registered taskstats version 1 [ 8.817239][ T1] Loading compiled-in X.509 certificates [ 8.823047][ T1] zswap: loaded using pool lzo/zbud [ 8.829089][ T1] Key type ._fscrypt registered [ 8.833812][ T1] Key type .fscrypt registered [ 8.858181][ T1] Key type big_key registered [ 8.866913][ T1] Key type encrypted registered [ 8.875568][ T1] hctosys: unable to open rtc device (rtc0) [ 8.882321][ T1] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 8.890644][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 8.899758][ T1] 1f00 14336 mtdblock0 [ 8.899763][ T1] (driver?) [ 8.907688][ T1] 1f01 116736 mtdblock1 [ 8.907694][ T1] (driver?) [ 8.915660][ T1] 0800 78150744 sda [ 8.915665][ T1] driver: sd [ 8.923220][ T1] 0801 16384 sda1 00008000-01 [ 8.923225][ T1] [ 8.931018][ T1] 0802 4194304 sda2 00008000-02 [ 8.931023][ T1] [ 8.939066][ T1] 0803 73939030 sda3 00008000-03 [ 8.939072][ T1] [ 8.946833][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 8.955783][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.101-oxnas-tld-1 #1.0 [ 8.963681][ T1] Hardware name: Generic DT based system [ 8.969182][ T1] [<c01095c8>] (unwind_backtrace) from [<c0105b0c>] (show_stack+0x10/0x14) [ 8.977625][ T1] [<c0105b0c>] (show_stack) from [<c0863a14>] (dump_stack+0xb4/0xd0) [ 8.985546][ T1] [<c0863a14>] (dump_stack) from [<c085a3f0>] (panic+0x10c/0x30c) [ 8.993208][ T1] [<c085a3f0>] (panic) from [<c0c013cc>] (mount_block_root+0x1e0/0x2a4) [ 9.001387][ T1] [<c0c013cc>] (mount_block_root) from [<c0c01588>] (mount_root+0xf8/0x138) [ 9.009909][ T1] [<c0c01588>] (mount_root) from [<c0c016f8>] (prepare_namespace+0x130/0x194) [ 9.018606][ T1] [<c0c016f8>] (prepare_namespace) from [<c0863bc8>] (kernel_init+0x8/0x110) [ 9.027212][ T1] [<c0863bc8>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c) [ 9.035461][ T1] Exception stack(0xc783ffb0 to 0xc783fff8) [ 9.041198][ T1] ffa0: 00000000 00000000 00000000 00000000 [ 9.050058][ T1] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 9.058915][ T1] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 9.066229][ C1] CPU1: stopping [ 9.069655][ C1] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.4.101-oxnas-tld-1 #1.0 [ 9.077557][ C1] Hardware name: Generic DT based system [ 9.083054][ C1] [<c01095c8>] (unwind_backtrace) from [<c0105b0c>] (show_stack+0x10/0x14) [ 9.091491][ C1] [<c0105b0c>] (show_stack) from [<c0863a14>] (dump_stack+0xb4/0xd0) [ 9.099407][ C1] [<c0863a14>] (dump_stack) from [<c01081dc>] (handle_IPI+0x198/0x1e0) [ 9.107496][ C1] [<c01081dc>] (handle_IPI) from [<c050e3b0>] (gic_handle_irq+0x7c/0x8c) [ 9.115758][ C1] [<c050e3b0>] (gic_handle_irq) from [<c0101a6c>] (__irq_svc+0x6c/0xa8) [ 9.123921][ C1] Exception stack(0xc7871f60 to 0xc7871fa8) [ 9.129666][ C1] 1f60: 00000a74 00000000 c7ee94b4 00000000 00000000 ffffe000 c0d03c88 00000002 [ 9.138531][ C1] 1f80: c0d03ccc 00000000 00000000 c0d03c68 00000000 c7871fb0 c0103574 c0103578 [ 9.147389][ C1] 1fa0: 60000013 ffffffff [ 9.151575][ C1] [<c0101a6c>] (__irq_svc) from [<c0103578>] (arch_cpu_idle+0x28/0x30) [ 9.159662][ C1] [<c0103578>] (arch_cpu_idle) from [<c013ced0>] (do_idle+0x1f4/0x254) [ 9.167746][ C1] [<c013ced0>] (do_idle) from [<c013d210>] (cpu_startup_entry+0x18/0x1c) [ 9.176007][ C1] [<c013d210>] (cpu_startup_entry) from [<60102428>] (0x60102428) [ 9.183667][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS DRAM: 128 MiB IDE: Bus 0: OK Device 0: Model: ST98823AS Firm: 3.04 Ser#: 5PK0ZQQV Type: Hard Disk Supports 48-bit addressing Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) NAND: 128 MiB reading u-boot.env In: serial Out: serial Err: serial Net: mii0 ## Error: "safeboot" not defined Hit any key to stop autoboot: 0 OX820 # printenv SET_dtb=fdt addr ${fdtaddr} ; fdt header autoload=no baudrate=115200 bootcmd=run ideboot bootdelay=3 bootnew=bootm 60000000 - 61000000 bootold=bootm 60000000 console=console=ttyS0,115200n8 ethact=mii0 ethaddr=74:F0:6D:6A:1D:17 ext2_dtb=ext2load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb ext2_ideboot=run ext2_uimage ; run ext2_dtb ; run SET_dtb ; run bootnew ext2_uimage=ext2load ide 0:2 60000000 /boot/uImage ext4_dtb=ext4load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb ext4_ideboot=run ext4_uimage ; run ext4_dtb ; run SET_dtb ; run bootnew ext4_uimage=ext4load ide 0:2 60000000 /boot/uImage fdtaddr=61000000 filesize=1b79 ideboot=run ext4_ideboot idebootold=${loadold} ;${bootold} imgaddr=60000000 ipaddr=10.0.0.71 keypressed=1 mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) netcon=echo switch to net console;setenv stderr nc;setenv stdin nc;setenv stdout nc;echo switch to net console preboot=run safeboot serialcon=echo switch to serial console;setenv stderr serial;setenv stdin serial;setenv stdout serial;echo switch to serial console stderr=serial stdin=serial stdout=serial updboot=bootp;tftp 60000000 u-boot.img;ide write 60000000 400 400 Environment size: 1267/16380 bytes OX820 #
Re: Kernel crash during boot 5.4.101-oxnas-tld-1 May 04, 2021 04:29AM |
Admin Registered: 13 years ago Posts: 18,564 |
> OX820 # printenv > SET_dtb=fdt addr ${fdtaddr} ; fdt header > autoload=no > baudrate=115200 > bootcmd=run ideboot > bootdelay=3 > bootnew=bootm 60000000 - 61000000 > bootold=bootm 60000000 > console=console=ttyS0,115200n8 > ethact=mii0 > ethaddr=74:F0:6D:6A:1D:17 > ext2_dtb=ext2load ide 0:2 61000000 > /boot/dts/ox820-pogoplug-classic.dtb > ext2_ideboot=run ext2_uimage ; run ext2_dtb ; run > SET_dtb ; run bootnew > ext2_uimage=ext2load ide 0:2 60000000 > /boot/uImage > ext4_dtb=ext4load ide 0:2 61000000 > /boot/dts/ox820-pogoplug-classic.dtb > ext4_ideboot=run ext4_uimage ; run ext4_dtb ; run > SET_dtb ; run bootnew > ext4_uimage=ext4load ide 0:2 60000000 > /boot/uImage > fdtaddr=61000000 > filesize=1b79 > ideboot=run ext4_ideboot > idebootold=${loadold} ;${bootold} > imgaddr=60000000 > ipaddr=10.0.0.71 > keypressed=1 > mtdids=nand0=41000000.nand > mtdparts=mtdparts=41000000.nand:14m(boot),-(data) > netcon=echo switch to net console;setenv stderr > nc;setenv stdin nc;setenv stdout nc;echo switch to > net console > preboot=run safeboot > serialcon=echo switch to serial console;setenv > stderr serial;setenv stdin serial;setenv stdout > serial;echo switch to serial console > stderr=serial > stdin=serial > stdout=serial > updboot=bootp;tftp 60000000 u-boot.img;ide write > 60000000 400 400 > > Environment size: 1267/16380 bytes > OX820 #
ext2_ideboot=run ext2_uimage ; run ext2_dtb ; run SET_dtb ; run bootnew
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial' setenv bootcmd 'run set_bootargs; run ideboot'
boot
Re: Kernel crash during boot 5.4.101-oxnas-tld-1 May 05, 2021 03:01AM |
Registered: 2 years ago Posts: 4 |
Re: Kernel crash during boot 5.4.101-oxnas-tld-1 May 05, 2021 04:33PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Kernel crash during boot 5.4.101-oxnas-tld-1 May 07, 2021 06:35AM |
Registered: 2 years ago Posts: 4 |
mkfs.ext4 -L rootfs $HDD"2"
mkfs.ext2 -L rootfs $HDD"2"
OX820 # printenv SET_dtb=fdt addr ${fdtaddr} ; fdt header autoload=no baudrate=115200 bootcmd=run set_bootargs; run ideboot bootdelay=3 bootnew=bootm 60000000 - 61000000 bootold=bootm 60000000 console=console=ttyS0,115200n8 ethact=mii0 ethaddr=00:25:31:02:87:12 ext2_dtb=ext2load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb ext2_ideboot=run ext2_uimage ; run ext2_dtb ; run SET_dtb ; run bootnew ext2_uimage=ext2load ide 0:2 60000000 /boot/uImage ext4_dtb=ext4load ide 0:2 61000000 /boot/dts/ox820-pogoplug-classic.dtb ext4_ideboot=run ext4_uimage ; run ext4_dtb ; run SET_dtb ; run bootnew ext4_uimage=ext4load ide 0:2 60000000 /boot/uImage fdtaddr=61000000 filesize=1b79 ideboot=run ext4_ideboot idebootold=${loadold} ;${bootold} imgaddr=60000000 ipaddr=10.0.0.71 keypressed=1 mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) netcon=echo switch to net console;setenv stderr nc;setenv stdin nc;setenv stdout nc;echo switch to net console preboot=run safeboot serialcon=echo switch to serial console;setenv stderr serial;setenv stdin serial;setenv stdout serial;echo switch to serial console set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda2 rootdelay=10 $mtdparts earlyprintk=serial stderr=serial stdin=serial stdout=serial updboot=bootp;tftp 60000000 u-boot.img;ide write 60000000 400 400 Environment size: 1394/16380 bytes OX820 #
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2021.05.07 13:10:16 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) Boot device: SATA Attempting to set PLLA to 800 MHz ... plla_ctrl0 : 0000030a plla_ctrl1 : 00400000 plla_ctrl2 : 007f0068 plla_ctrl3 : 00000193 PLLA Set Bus 0: OK Device 0: reading bootargs.bin reading u-boot.img reading u-boot.img U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS DRAM: 128 MiB IDE: Bus 0: OK Device 0: Model: ST98823AS Firm: 3.04 Ser#: 5PK0ZQQV Type: Hard Disk Supports 48-bit addressing Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) NAND: 128 MiB reading u-boot.env In: serial Out: serial Err: serial Net: mii0 ## Error: "safeboot" not defined Hit any key to stop autoboot: 3 2 1 0 5502688 bytes read in 1173 ms (4.5 MiB/s) 8618 bytes read in 34 ms (247.1 KiB/s) magic:0xd00dfeed totalsize:0x21aa (8618) off_dt_struct:0x38 off_dt_strings:0x1e80 off_mem_rsvmap:0x28 version:17 last_comp_version:16 boot_cpuid_phys:0x0 size_dt_strings:0x32a size_dt_struct:0x1e48 number mem_rsv:0x0 ## Booting kernel from Legacy Image at 60000000 ... Image Name: Linux-5.4.101-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5502624 Bytes = 5.2 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 61000000 Booting using the fdt blob at 0x61000000 Loading Kernel Image ... OK Loading Device Tree to 67e26000, end 67e2b1a9 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.4.101-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 SMP PREEMPT Sat Feb 27 20:19:53 PST 2021 [ 0.000000][ T0] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Pogoplug V3 Classic [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] percpu: Embedded 15 pages/cpu s30508 r8192 d22740 u61440 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda2 rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 116968K/131072K available (8192K kernel code, 232K rwdata, 2088K rodata, 1024K init, 260K bss, 14104K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_random_seq_create+0x78/0x12c with crng_init=0 [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16 [ 0.000017][ T0] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.008783][ T0] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.020119][ T0] timer_oxnas_rps: Registered clocksource rate 390625Hz [ 0.026882][ T0] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500 [ 0.036044][ T0] GIC: PPI13 is secure or misconfigured [ 0.041456][ T0] GIC: PPI13 is secure or misconfigured [ 0.047037][ T0] Console: colour dummy device 80x30 [ 0.052267][ T0] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440) [ 0.108472][ T0] pid_max: default: 32768 minimum: 301 [ 0.114196][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.122204][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.130767][ T0] *** VALIDATE tmpfs *** [ 0.135920][ T0] *** VALIDATE proc *** [ 0.140126][ T0] *** VALIDATE cgroup1 *** [ 0.144432][ T0] *** VALIDATE cgroup2 *** [ 0.148807][ T0] CPU: Testing write buffer coherency: ok [ 0.156577][ T1] Setting up static identity map for 0x60100000 - 0x60100038 [ 0.164136][ T1] rcu: Hierarchical SRCU implementation. [ 0.170498][ T1] smp: Bringing up secondary CPUs ... [ 0.176936][ T0] GIC: PPI13 is secure or misconfigured [ 0.231864][ T1] smp: Brought up 1 node, 2 CPUs [ 0.242101][ T1] SMP: Total of 2 processors activated (638.97 BogoMIPS). [ 0.250019][ T1] devtmpfs: initialized [ 0.259842][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.270415][ T1] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.278051][ T1] prandom: seed boundary self test passed [ 0.288066][ T1] prandom: 100 self tests passed [ 0.292864][ T1] pinctrl core: initialized pinctrl subsystem [ 0.300175][ T1] NET: Registered protocol family 16 [ 0.307274][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.318072][ T1] cpuidle: using governor ladder [ 0.323074][ T1] cpuidle: using governor menu [ 7.325235][ T1] vgaarb: loaded [ 7.329456][ T1] SCSI subsystem initialized [ 7.334760][ T1] usbcore: registered new interface driver usbfs [ 7.340999][ T1] usbcore: registered new interface driver hub [ 7.347343][ T1] usbcore: registered new device driver usb [ 7.353413][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.359047][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.368903][ T1] PTP clock support registered [ 7.375168][ T1] clocksource: Switched to clocksource oxnas_rps_clocksource_timer [ 7.383370][ T1] *** VALIDATE bpf *** [ 7.387783][ T1] *** VALIDATE ramfs *** [ 7.412083][ T1] NET: Registered protocol family 2 [ 7.418270][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 7.427412][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 7.435814][ T1] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 7.443545][ T1] TCP: Hash tables configured (established 1024 bind 1024) [ 7.450798][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 7.458094][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 7.466058][ T1] NET: Registered protocol family 1 [ 7.472335][ T1] RPC: Registered named UNIX socket transport module. [ 7.479029][ T1] RPC: Registered udp transport module. [ 7.484410][ T1] RPC: Registered tcp transport module. [ 7.489832][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.496993][ T1] PCI: CLS 0 bytes, default 32 [ 7.503319][ T1] Initialise system trusted keyrings [ 7.508574][ T1] Key type blacklist registered [ 7.513653][ T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 7.531607][ T1] zbud: loaded [ 7.540011][ T1] NFS: Registering the id_resolver key type [ 7.545858][ T1] Key type id_resolver registered [ 7.550714][ T1] Key type id_legacy registered [ 7.555456][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 7.562816][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.571097][ T1] fuse: init (API version 7.31) [ 7.576028][ T1] *** VALIDATE fuse *** [ 7.580032][ T1] *** VALIDATE fuse *** [ 7.584878][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 7.592394][ T1] orangefs_init: module version upstream loaded [ 7.652746][ T1] Key type asymmetric registered [ 7.657589][ T1] Asymmetric key parser 'x509' registered [ 7.663216][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 7.673697][ T1] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 7.682444][ T1] printk: console [ttyS0] disabled [ 7.687621][ T1] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A [ 7.697221][ T1] printk: console [ttyS0] enabled [ 7.697221][ T1] printk: console [ttyS0] enabled [ 7.706961][ T1] printk: bootconsole [earlycon0] disabled [ 7.706961][ T1] printk: bootconsole [earlycon0] disabled [ 7.732802][ T1] loop: module loaded [ 7.738872][ T1] scsi host0: sata_oxnas [ 7.743626][ T1] ata1: SATA max UDMA/133 irq 57 [ 7.748610][ T75] sata_oxnas: resetting SATA core [ 7.815539][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it [ 7.824883][ T1] ONFI parameter recovery failed, aborting [ 7.830602][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 7.837660][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit [ 7.842782][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.851061][ T1] Scanning device for bad blocks [ 7.939212][ T1] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller [ 7.947832][ T1] Creating 2 MTD partitions on "41000000.nand-controller": [ 7.954859][ T1] 0x000000000000-0x000000e00000 : "boot" [ 7.963000][ T1] 0x000000e00000-0x000008000000 : "data" [ 7.972129][ T1] libphy: Fixed MDIO Bus: probed [ 7.977287][ T1] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found [ 7.984107][ T1] oxnas-dwmac 40400000.ethernet: PTP uses main clock [ 7.990671][ T1] oxnas-dwmac 40400000.ethernet: no reset control found [ 8.065582][ T1] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35 [ 8.073233][ T1] oxnas-dwmac 40400000.ethernet: DWMAC1000 [ 8.079022][ T1] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported [ 8.087042][ T1] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported [ 8.095029][ T1] oxnas-dwmac 40400000.ethernet: COE Type 2 [ 8.100797][ T1] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported [ 8.108375][ T1] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported [ 8.115432][ T1] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors [ 8.122887][ T1] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors [ 8.130216][ T1] oxnas-dwmac 40400000.ethernet: Ring mode enabled [ 8.136586][ T1] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 8.155258][ T1] libphy: stmmac: probed [ 8.159367][ T1] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 8.169617][ T1] mdio_bus stmmac-0:03: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:03, irq=POLL) [ 8.180828][ T1] PPP generic driver version 2.4.2 [ 8.186224][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.193418][ T1] ehci-pci: EHCI PCI platform driver [ 8.255239][ T75] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 8.263500][ T75] ata1.00: ATA-7: ST98823AS, 3.04, max UDMA/133 [ 8.269683][ T75] ata1.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 8.278725][ T75] ata1.00: configured for UDMA/133 [ 8.284334][ T7] scsi 0:0:0:0: Direct-Access ATA ST98823AS 3.04 PQ: 0 ANSI: 5 [ 8.295485][ T54] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) [ 8.303946][ T54] sd 0:0:0:0: [sda] Write Protect is off [ 8.309739][ T54] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.334850][ T54] sda: sda1 sda2 sda3 [ 8.342054][ T54] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.405248][ T1] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 8.411453][ T1] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 8.420047][ T1] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100 [ 8.455226][ T1] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 8.462295][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 8.471285][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.479216][ T1] usb usb1: Product: EHCI Host Controller [ 8.484769][ T1] usb usb1: Manufacturer: Linux 5.4.101-oxnas-tld-1 ehci_hcd [ 8.491993][ T1] usb usb1: SerialNumber: 40200100.ehci [ 8.498467][ T1] hub 1-0:1.0: USB hub found [ 8.503011][ T1] hub 1-0:1.0: 2 ports detected [ 8.509045][ T1] usbcore: registered new interface driver cdc_wdm [ 8.515609][ T1] usbcore: registered new interface driver usb-storage [ 8.522503][ T1] usbcore: registered new interface driver usbserial_generic [ 8.529825][ T1] usbserial: USB Serial support registered for generic [ 8.536983][ T1] mousedev: PS/2 mouse device common for all mice [ 8.543380][ T1] i2c /dev entries driver [ 8.549073][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 8.555461][ T1] usbcore: registered new interface driver usbhid [ 8.561704][ T1] usbhid: USB HID core driver [ 8.567859][ T1] NET: Registered protocol family 10 [ 8.574694][ T1] Segment Routing with IPv6 [ 8.579276][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 8.588003][ T1] NET: Registered protocol family 17 [ 8.593541][ T1] Key type dns_resolver registered [ 8.599280][ T1] registered taskstats version 1 [ 8.604060][ T1] Loading compiled-in X.509 certificates [ 8.609843][ T1] zswap: loaded using pool lzo/zbud [ 8.615912][ T1] Key type ._fscrypt registered [ 8.620605][ T1] Key type .fscrypt registered [ 8.644352][ T1] Key type big_key registered [ 8.653276][ T1] Key type encrypted registered [ 8.662003][ T1] hctosys: unable to open rtc device (rtc0) [ 8.668577][ T1] Waiting 10 sec before mounting root device... [ 8.875230][ T21] usb 1-1: new high-speed USB device number 2 using oxnas-ehci [ 9.077084][ T21] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.64 [ 9.086000][ T21] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 9.093834][ T21] usb 1-1: Product: USB2.0 Hub [ 9.099665][ T21] hub 1-1:1.0: USB hub found [ 9.104591][ T21] hub 1-1:1.0: 4 ports detected [ 19.089267][ T1] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null) [ 19.097162][ T1] VFS: Mounted root (ext4 filesystem) readonly on device 8:2. [ 19.160010][ T1] devtmpfs: mounted [ 19.165358][ T1] Freeing unused kernel memory: 1024K [ 19.171960][ T1] Checked W+X mappings: passed, no W+X pages found [ 19.178339][ T1] Run /sbin/init as init process [ 20.644945][ C0] random: fast init done [ 20.858004][ T1] systemd[1]: System time before build time, advancing clock. [ 21.132551][ T1] systemd[1]: Inserted module 'autofs4' [ 21.275102][ T1] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 21.298275][ T1] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 10 (buster)! [ 21.355230][ T1] systemd[1]: Set hostname to <debian>. [ 22.928737][ T1] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 22.946664][ T1] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 23.577840][ T1] systemd[1]: /lib/systemd/system/smbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/smbd.pid /run/samba/smbd.pid; please update the unit file accordingly. [ 23.658560][ T1] systemd[1]: /lib/systemd/system/nmbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/nmbd.pid /run/samba/nmbd.pid; please update the unit file accordingly. [ 23.866734][ T1] systemd[1]: /lib/systemd/system/rpc-statd.service:13: PIDFile= references path below legacy directory /var/run/, updating /var/run/rpc.statd.pid /run/rpc.statd.pid; please update the unit file accordingly. [ 24.004677][ T1] random: systemd: uninitialized urandom read (16 bytes read) [ 24.031252][ T1] random: systemd: uninitialized urandom read (16 bytes read) [ 24.038781][ T1] systemd[1]: Reached target System Time Synchronized. [ OK ] Reached target System Time Synchronized. [ 24.075640][ T1] random: systemd: uninitialized urandom read (16 bytes read) [ 24.085376][ T1] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Created slice system-getty.slice. [ OK ] Started Forward Password Ruests to Wall Directory Watch. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on udev Control Socket. [ OK ] Set up automount Arbitrarys File System Automount Point. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Started Dispatch Password ts to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Listening on Journal Socket. Mounting RPC Pipe File System... Mounting Kernel Debug File System... Starting File System Check on Root Device... Starting Create list of reodes for the current kernel... Starting Load Kernel Modules... Mounting NFSD configuration filesystem... Mounting POSIX Message Queue File System... [ OK ] Listening on udev Kernel Socket. Starting udev Coldplug all Devices... [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Mounted RPC Pipe File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Started Create list of req nodes for the current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Mounted NFSD configuration filesystem. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started File System Check Daemon to report status. Mounting FUSE Control File System... Starting Apply Kernel Variables... Starting pNFS block layout mapping daemon... [ OK ] Mounted FUSE Control File System. [ OK ] Started File System Check on Root Device. [ OK ] Started pNFS block layout mapping daemon. [ OK ] Started Journal Service. [ OK ] Started Apply Kernel Variables. Starting Remount Root and Kernel File Systems... [ 25.909207][ T133] __nand_correct_data: uncorrectable ECC error [ 25.915486][ T133] __nand_correct_data: uncorrectable ECC error [ 25.921505][ T133] blk_update_request: I/O error, dev mtdblock0, sector 512 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 25.935490][ T133] __nand_correct_data: uncorrectable ECC error [ 25.941493][ T133] __nand_correct_data: uncorrectable ECC error [ 25.948904][ T133] blk_update_request: I/O error, dev mtdblock0, sector 512 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 25.960680][ T133] Buffer I/O error on dev mtdblock0, logical block 64, async page read [ OK ] Started udev Coldplug all Devices. Starting Helper to synchronize boot up for ifupdown... [ 26.532925][ T133] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ OK ] Started Remount Root and Kernel File Systems. Activating swap /swapfile1... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Create System Users... [ 26.966520][ T122] systemd-journald[122]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. [ OK ] Found device /dev/ttyS0. [ 29.455662][ T137] Adding 524284k swap on /swapfile1. Priority:-2 extents:7 across:835580k FS [ OK ] Activated swap /swapfile1. [ OK ] Started Helper to synchronize boot up for ifupdown. [ OK ] Found device ST98823AS home. Starting File System Check on /dev/sda3... [ OK ] Reached target Swap. Mounting /tmp... [ OK ] Mounted /tmp. Checking in progress on 1 disk (0.0% complete) [ 33.091737][ C0] random: crng init done [ 33.095838][ C0] random: 7 urandom warning(s) missed due to ratelimiting Checking in progress on 1 disk (2.2% complete) Checking in progress on 1 disk (100.0% complete) Checking in progress on 1 disk (100.0% complete) Checking in progress on 1 disk (100.0% complete) Checking in progress on 1 disk (100.0% complete) Checking in progress on 0 disks (100.0% complete) [ OK ] Started File System Check on /dev/sda3. Mounting /home... [ 101.528980][ T174] ext2 filesystem being mounted at /home supports timestamps until 2038 (0x7fffffff) [ OK ] Mounted /home. [ OK ] Reached target Local File Systems. Starting Raise network interfaces... Starting Create Volatile Files and Directories... Starting Preprocess NFS configuration... [ OK ] Started Preprocess NFS configuration. Starting NFSv4 ID-name mapping service... [ OK ] Reached target NFS client services. [ OK ] Started NFSv4 ID-name mapping service. [ OK ] Started Create Volatile Files and Directories. Starting RPC bind portmap service... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Login Service... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started RPC bind portmap service. [ 103.765442][ T213] oxnas-dwmac 40400000.ethernet eth0: PHY [stmmac-0:00] driver [Generic PHY] [ 103.781757][ T213] oxnas-dwmac 40400000.ethernet eth0: No Safety Features support found [ 103.790021][ T213] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ OK ] Reached target RPC Port Mapper. [ 103.805073][ T213] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock [ 103.813450][ T213] oxnas-dwmac 40400000.ethernet eth0: configuring for phy/rgmii link mode [ OK ] Started Login Service. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ 108.995801][ T123] oxnas-dwmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 109.004935][ T123] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. Starting OpenBSD Secure Shell server... [ OK ] Reached target Network is Online. Starting /etc/rc.local Compatibility... Starting Network Time Service... Starting Samba NMB Daemon... Starting NFS Mount Daemon... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started Network Time Service. [ OK ] Started NFS Mount Daemon. Starting NFS server and services... [ 116.479559][ T258] NFSD: Using UMH upcall client tracking operations. [ 116.486208][ T258] NFSD: starting 90-second grace period (net f0000129) [ OK ] Started NFS server and services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting LSB: Starts syslogd... Starting Permit User Sessions... [ OK ] Started Permit User Sessions. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Starts syslogd. Starting LSB: Starts klogd... [ OK ] Started LSB: Starts klogd. [ OK ] Started Samba NMB Daemon. Starting Samba SMB Daemon... [ OK ] Started Samba SMB Daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Debian GNU/Linux 10 debian ttyS0 debian login:
Re: Kernel crash during boot 5.4.101-oxnas-tld-1 May 07, 2021 05:09PM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
The only line I had to change was line 107 of the script from:
mkfs.ext4 -L rootfs $HDD"2"
to
mkfs.ext2 -L rootfs $HDD"2"
Re: Kernel crash during boot 5.4.101-oxnas-tld-1 May 08, 2021 11:09AM |
Registered: 2 years ago Posts: 4 |
Quote
BTW, you should use at least Ext3, not Ext2. Power outage will cause problem for Ext2. But Ext3 or Ext4 will be fine when that happens.
Starting Remount Root and Kernel File Systems... [ 25.909207][ T133] __nand_correct_data: uncorrectable ECC error [ 25.915486][ T133] __nand_correct_data: uncorrectable ECC error [ 25.921505][ T133] blk_update_request: I/O error, dev mtdblock0, sector 512 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 25.935490][ T133] __nand_correct_data: uncorrectable ECC error [ 25.941493][ T133] __nand_correct_data: uncorrectable ECC error [ 25.948904][ T133] blk_update_request: I/O error, dev mtdblock0, sector 512 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 25.960680][ T133] Buffer I/O error on dev mtdblock0, logical block 64, async page read
Re: Kernel crash during boot 5.4.101-oxnas-tld-1 May 08, 2021 04:34PM |
Admin Registered: 13 years ago Posts: 18,564 |
blkidand then check dmesg
dmesg | tail