|
Marvell development board (db-mv784mp-gp) cannot start Debian October 14, 2021 12:10AM |
Registered: 3 years ago Posts: 34 |
BootROM 1.20 Booting from SPI flash U-Boot SPL 2017.03 (Oct 13 2021 - 21:01:08) High speed PHY - Version: 2.1.5 (COM-PHY-V20) High speed PHY - Ended Successfully DDR3 Training Sequence - Ver 5.7.4 DDR3 Training Sequence - Number of DIMMs detected: 1 DDR3 Training Sequence - Ended Successfully Trying to boot from SPI U-Boot 2017.03 (Oct 13 2021 - 21:01:08 -0700) SoC: MV78460-B0 at 1600 MHz I2C: ready DRAM: 4 GiB (800 MHz, ECC not enabled) NAND: failed to scan nand at cs 0 0 MiB SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB Model: Marvell Armada XP Development Board DB-MV784MP-GP Board: Marvell DB-MV784MP-GP Net: eth0: ethernet@70000, eth1: ethernet@74000, eth2: ethernet@30000, eth3: ethernet@34000 Hit any key to stop autoboot: 0 => pri baudrate=115200 bootargs=console=ttyS0,115200 rootdelay=10 earlyprintk=serial bootcmd=sata init; ext2load sata 0:1 0x1000000 uImage; ext2load sata 0:1 0x2000000 uIinitrd; bootm 0x1000000 0x2000000 bootdelay=3 eth1addr=00:50:43:2e:28:68 eth2addr=00:50:43:28:68:22 eth3addr=00:50:43:68:22:2e ethact=ethernet@70000 ethaddr=00:11:32:42:ac:cb fdtcontroladdr=bfb44d98 fileaddr=800000 filesize=4fe87b ipaddr=10.0.0.100 loadaddr=0x800000 serverip=10.0.0.10 stderr=serial@12000 stdin=serial@12000 stdout=serial@12000 Environment size: 545/65532 bytes =>
=> boot 5236859 bytes read in 118 ms (42.3 MiB/s) ** File not found uIinitrd ** ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux-5.13.8-mvebu-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5236795 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Wrong Ramdisk Image Format Ramdisk image is corrupt or invalid => bootm 0x1000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux-5.13.8-mvebu-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5236795 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 [ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: div instructions available: patching division code [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Marvell Armada XP Development Board DB-MV784MP-GP [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x00000000ffffefff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x00000000ffffefff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x00000000ffffefff] [ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 1047039 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 rootdelay=10 earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 4142088K/4194300K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 52212K reserved, 0K cma-reserved, 3407856K highmem) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] ------------[ cut here ]------------ [ 0.000000][ T0] kernel BUG at drivers/irqchip/irq-armada-370-xp.c:752! [ 0.000000][ T0] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM [ 0.000000][ T0] Modules linked in: [ 0.000000][ T0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.8-mvebu-tld-1 #1.0 [ 0.000000][ T0] Hardware name: Marvell Armada 370/XP (Device Tree) [ 0.000000][ T0] PC is at armada_370_xp_mpic_of_init+0x78/0x37c [ 0.000000][ T0] LR is at cpu_cache_get+0xc/0x20 [ 0.000000][ T0] pc : [<c1024fcc>] lr : [<c02a0c78>] psr: 600000d3 [ 0.000000][ T0] sp : c1101ec8 ip : f1020ccf fp : c12618f0 [ 0.000000][ T0] r10: c0e899f1 r9 : c1261902 r8 : c1101f54 [ 0.000000][ T0] r7 : c1109fc8 r6 : 00000000 r5 : edfef578 r4 : c180d7c0 [ 0.000000][ T0] r3 : 00000000 r2 : 00000000 r1 : c0dd394b r0 : 00000000 [ 0.000000][ T0] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none [ 0.000000][ T0] Control: 10c5387d Table: 0000406a DAC: 00000051 [ 0.000000][ T0] Register r0 information: NULL pointer [ 0.000000][ T0] Register r1 information: non-slab/vmalloc memory [ 0.000000][ T0] Register r2 information: NULL pointer [ 0.000000][ T0] Register r3 information: NULL pointer [ 0.000000][ T0] Register r4 information: slab kmalloc-64 start c180d7c0 pointer offset 0 size 64 [ 0.000000][ T0] Register r5 information: non-slab/vmalloc memory [ 0.000000][ T0] Register r6 information: NULL pointer [ 0.000000][ T0] Register r7 information: non-slab/vmalloc memory [ 0.000000][ T0] Register r8 information: non-slab/vmalloc memory [ 0.000000][ T0] Register r9 information: non-slab/vmalloc memory [ 0.000000][ T0] Register r10 information: non-slab/vmalloc memory [ 0.000000][ T0] Register r11 information: non-slab/vmalloc memory [ 0.000000][ T0] Register r12 information: non-paged memory [ 0.000000][ T0] Process swapper/0 (pid: 0, stack limit = 0x(ptrval)) [ 0.000000][ T0] Stack: (0xc1101ec8 to 0xc1102000) [ 0.000000][ T0] 1ec0: 00000000 00000000 00000004 00000000 0000006d f1020a00 [ 0.000000][ T0] 1ee0: f1020ccf edfef5e4 00000200 00000000 00000000 00000000 00000000 f1021070 [ 0.000000][ T0] 1f00: f10210c7 edfef5e4 00000200 00000000 00000000 00000000 00000000 00000000 [ 0.000000][ T0] 1f20: c180d7c0 00000000 c1101f54 c1101f5c c1101f54 c1261902 c0e899f1 c1035a30 [ 0.000000][ T0] 1f40: c1837e00 00000000 0000003f c1109fc8 00000000 c1101f54 c1101f54 c1101f5c [ 0.000000][ T0] 1f60: c1101f5c 00000000 c1837e00 c1042f48 ffffffff c1273000 00000000 efffcc40 [ 0.000000][ T0] 1f80: c1273000 efffcc00 c1042000 c1009874 c1042f48 c100326c c12a256c c100107c [ 0.000000][ T0] 1fa0: ffffffff ffffffff 00000000 c10005a0 c1109fc8 c1109fc0 c1042f58 00000035 [ 0.000000][ T0] 1fc0: c1042f58 00000000 00000000 00000000 00000000 c1000330 00000051 10c0387d [ 0.000000][ T0] 1fe0: 00000000 0176d3d8 562f5842 10c5387d 00000000 00000000 00000000 00000000 [ 0.000000][ T0] [<c1024fcc>] (armada_370_xp_mpic_of_init) from [<c1035a30>] (of_irq_init+0x1f0/0x300) [ 0.000000][ T0] [<c1035a30>] (of_irq_init) from [<c1009874>] (mvebu_init_irq+0x8/0x64) [ 0.000000][ T0] [<c1009874>] (mvebu_init_irq) from [<c100326c>] (init_IRQ+0x68/0x78) [ 0.000000][ T0] [<c100326c>] (init_IRQ) from [<c100107c>] (start_kernel+0x52c/0x86c) [ 0.000000][ T0] [<c100107c>] (start_kernel) from [<00000000>] (0x0) [ 0.000000][ T0] Code: e59f02d8 ebc42dbf e3500000 1a000001 (e7f001f2) [ 0.000000][ T0] ---[ end trace aa3fe55bef28eab3 ]--- [ 0.000000][ T0] Kernel panic - not syncing: Attempted to kill the idle task! [ 0.000000][ T0] ---[ end Kernel panic - not syncing: Attempted to kill the idle task! ]---
/* * Device Tree file for Marvell Armada XP development board * (DB-MV784MP-GP) * * Copyright (C) 2013-2014 Marvell * * Lior Amsalem <alior@marvell.com> * Gregory CLEMENT <gregory.clement@free-electrons.com> * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual * licensing only applies to this file, and not this project as a * whole. * * a) This file is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of the * License, or (at your option) any later version. * * This file is distributed in the hope that it will be useful * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * Or, alternatively * * b) Permission is hereby granted, free of charge, to any person * obtaining a copy of this software and associated documentation * files (the "Software"), to deal in the Software without * restriction, including without limitation the rights to use * copy, modify, merge, publish, distribute, sublicense, and/or * sell copies of the Software, and to permit persons to whom the * Software is furnished to do so, subject to the following * conditions: * * The above copyright notice and this permission notice shall be * included in all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR * OTHER DEALINGS IN THE SOFTWARE. * * Note: this Device Tree assumes that the bootloader has remapped the * internal registers to 0xf1000000 (instead of the default * 0xd0000000). The 0xf1000000 is the default used by the recent, * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier * boards were delivered with an older version of the bootloader that * left internal registers mapped at 0xd0000000. If you are in this * situation, you should either update your bootloader (preferred * solution) or the below Device Tree should be adjusted. */ /dts-v1/; #include <dt-bindings/gpio/gpio.h> #include "armada-xp-mv78460.dtsi" / { model = "Marvell Armada XP Development Board DB-MV784MP-GP"; compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { stdout-path = "serial0:115200n8"; }; aliases { spi0 = &spi0; }; memory { device_type = "memory"; /* * 8 GB of plug-in RAM modules by default.The amount * of memory available can be changed by the * bootloader according the size of the module * actually plugged. However, memory between * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is * the address range used for I/O (internal registers, * MBus windows). */ reg = <0x00000000 0x00000000 0x00000000 0xf0000000>, <0x00000001 0x00000000 0x00000001 0x00000000>; }; cpus { pm_pic { ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>, <&gpio0 17 GPIO_ACTIVE_LOW>, <&gpio0 18 GPIO_ACTIVE_LOW>; }; }; soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>; devbus-bootcs { status = "okay"; /* Device Bus parameters are required */ /* Read parameters */ devbus,bus-width = <16>; devbus,turn-off-ps = <60000>; devbus,badr-skew-ps = <0>; devbus,acc-first-ps = <124000>; devbus,acc-next-ps = <248000>; devbus,rd-setup-ps = <0>; devbus,rd-hold-ps = <0>; /* Write parameters */ devbus,sync-enable = <0>; devbus,wr-high-ps = <60000>; devbus,wr-low-ps = <60000>; devbus,ale-wr-ps = <60000>; /* NOR 16 MiB */ nor@0 { compatible = "cfi-flash"; reg = <0 0x1000000>; bank-width = <2>; }; }; pcie-controller { status = "okay"; /* * The 3 slots are physically present as * standard PCIe slots on the board. */ pcie@1,0 { /* Port 0, Lane 0 */ status = "okay"; }; pcie@9,0 { /* Port 2, Lane 0 */ status = "okay"; }; pcie@10,0 { /* Port 3, Lane 0 */ status = "okay"; }; }; internal-regs { serial@12000 { status = "okay"; u-boot,dm-pre-reloc; }; serial@12100 { status = "okay"; }; serial@12200 { status = "okay"; }; serial@12300 { status = "okay"; }; pinctrl { pinctrl-0 = <&pic_pins>; pinctrl-names = "default"; pic_pins: pic-pins-0 { marvell,pins = "mpp16", "mpp17", "mpp18"; marvell,function = "gpio"; }; }; sata@a0000 { nr-ports = <2>; status = "okay"; }; mdio { phy0: ethernet-phy@0 { reg = <16>; }; phy1: ethernet-phy@1 { reg = <17>; }; phy2: ethernet-phy@2 { reg = <18>; }; phy3: ethernet-phy@3 { reg = <19>; }; }; ethernet@70000 { status = "okay"; phy = <&phy0>; phy-mode = "qsgmii"; }; ethernet@74000 { status = "okay"; phy = <&phy1>; phy-mode = "qsgmii"; }; ethernet@30000 { status = "okay"; phy = <&phy2>; phy-mode = "qsgmii"; }; ethernet@34000 { status = "okay"; phy = <&phy3>; phy-mode = "qsgmii"; }; /* Front-side USB slot */ usb@50000 { status = "okay"; }; /* Back-side USB slot */ usb@51000 { status = "okay"; }; spi0: spi@10600 { status = "okay"; u-boot,dm-pre-reloc; spi-flash@0 { u-boot,dm-pre-reloc; #address-cells = <1>; #size-cells = <1>; compatible = "n25q128a13", "jedec,spi-nor"; reg = <0>; /* Chip select 0 */ spi-max-frequency = <108000000>; }; }; nand@d0000 { status = "okay"; num-cs = <1>; marvell,nand-keep-config; marvell,nand-enable-arbiter; nand-on-flash-bbt; }; }; }; };
|
Re: Marvell development board (db-mv784mp-gp) cannot start Debian October 14, 2021 02:58AM |
Registered: 3 years ago Posts: 34 |
U-Boot 2021.10 (Oct 14 2021 - 00:40:12 -0700) SoC: MV78460-B0 at 1600 MHz I2C: ready DRAM: 4 GiB (800 MHz, 64-bit, ECC not enabled) NAND: 0 MiB Loading Environment from SPIFlash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 4 KiB, total 16 MiB OK Model: Marvell Armada XP Development Board DB-MV784MP-GP Board: Marvell DB-MV784MP-GP Net: eth0: ethernet@70000, eth1: ethernet@74000, eth2: ethernet@30000, eth3: ethernet@34000 Hit any key to stop autoboot: 0 => tftp 0x80000 uImage Unknown command 'tftp' - try 'help' => tftpboot 0x80000 uImage 88E1545 Initialized ethernet@70000 Waiting for PHY auto negotiation to complete..... done Using ethernet@70000 device TFTP from server 10.0.0.10; our IP address is 10.0.0.100 Filename 'uImage'. TFTP error: trying to overwrite reserved memory... => bdinfo boot_params = 0x00000100 DRAM bank = 0x00000000 -> start = 0x00000000 -> size = 0x80000000 DRAM bank = 0x00000001 -> start = 0x80000000 -> size = 0x80000000 flashstart = 0x00000000 flashsize = 0x00000000 flashoffset = 0x00000000 baudrate = 115200 bps relocaddr = 0xbff6c000 reloc off = 0xbf76c000 Build = 32-bit current eth = ethernet@70000 ethaddr = 00:11:32:42:ac:cb IP addr = 10.0.0.100 fdt_blob = 0xbfb575a0 new_fdt = 0xbfb575a0 fdt_size = 0x00004920 lmb_dump_all: memory.cnt = 0x1 memory[0] [0x80000000-0x7fffffff], 0x00000000 bytes flags: 0 reserved.cnt = 0x1 reserved[0] [0xbfb55b74-0xbfffffff], 0x004aa48c bytes flags: 0 arch_number = 0x00000000 TLB addr = 0xbfff0000 irq_sp = 0xbfb57590 sp start = 0xbfb57580 Early malloc usage: 2cc / 2000
|
Re: Marvell development board (db-mv784mp-gp) cannot start Debian October 14, 2021 03:28PM |
Admin Registered: 13 years ago Posts: 19,192 |
Quote
=> tftpboot 0x80000 uImage
|
Re: Marvell development board (db-mv784mp-gp) cannot start Debian October 16, 2021 05:03AM |
Registered: 3 years ago Posts: 34 |
memory {
device_type = "memory";
/*
* 8 GB of plug-in RAM modules by default.The amount
* of memory available can be changed by the
* bootloader according the size of the module
* actually plugged. However, memory between
* 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
* the address range used for I/O (internal registers,
* MBus windows).
*/
reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
<0x00000001 0x00000000 0x00000001 0x00000000>;
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000
MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>;
|
Re: Marvell development board (db-mv784mp-gp) cannot start Debian October 16, 2021 05:30AM |
Registered: 3 years ago Posts: 34 |
|
Re: Marvell development board (db-mv784mp-gp) cannot start Debian October 16, 2021 03:02PM |
Admin Registered: 13 years ago Posts: 19,192 |
|
Min1123
Re: Marvell development board (db-mv784mp-gp) cannot start Debian December 27, 2021 09:38AM |