Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 08, 2022 10:43PM |
Registered: 6 years ago Posts: 359 |
root@debian:~# sensors-detect # sensors-detect revision $Revision$ # DMI data unavailable, please consider installing dmidecode 2.7 # or later for better results. # Kernel: 5.9.12-kirkwood-tld-1 armv5tel # Processor: Feroceon 88FR131 rev 1 (v5l) (//) This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): yes modprobe: FATAL: Module cpuid not found in directory /lib/modules/5.9.12-kirkwood-tld-1 Failed to load module cpuid. Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 16h thermal sensors... No AMD Family 17h thermal sensors... No AMD Family 15h power sensors... No AMD Family 16h power sensors... No Intel digital thermal sensor... No Intel AMB FB-DIMM thermal sensor... No Intel 5500/5520/X58 thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): yes Sorry, no supported PCI bus adapters found. Next adapter: mv64xxx_i2c adapter (i2c-0) Do you want to scan it? (YES/no/selectively): YES Client found at address 0x4c Handled by driver `lm63' (already loaded), chip type `lm63' Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `lm63': * Bus `mv64xxx_i2c adapter' Busdriver `UNKNOWN', I2C address 0x4c Chip `lm63' (confidence: 6) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers lm63 #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO)yes Successful! Monitoring programs won't work until the needed modules are loaded. You may want to run '/etc/init.d/kmod start' to load them.
root@debian:~# sensors lm63-i2c-0-4c Adapter: mv64xxx_i2c adapter temp1: +45.0 C (high = +70.0 C) temp2: +43.4 C (low = +0.0 C, high = +70.0 C) (crit = +85.0 C, hyst = +75.0 C)
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 09, 2022 11:05AM |
Registered: 6 years ago Posts: 359 |
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 09, 2022 04:03PM |
Admin Registered: 12 years ago Posts: 17,933 |
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 09, 2022 04:29PM |
Registered: 6 years ago Posts: 359 |
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 09, 2022 04:59PM |
Admin Registered: 12 years ago Posts: 17,933 |
Re: Ctera C200 : This looks like a Kirkwood device 512MB mem 2 SATA January 10, 2022 09:30AM |
Registered: 6 years ago Posts: 359 |
U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 SoC: Kirkwood 88F6281_A1 Model: Ctera C200 V1 DRAM: 512 MiB NAND: 256 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial Net: eth0: ethernet-controller@72000 88E1116 Initialized on ethernet-controller@72000 ethernet-controller@72000 Waiting for PHY auto negotiation to complete....... done Using ethernet-controller@72000 device host 192.168.7.4 is alive ethernet-controller@72000 Waiting for PHY auto negotiation to complete........ done Using ethernet-controller@72000 device host 192.168.7.4 is alive ethernet-controller@72000 Waiting for PHY auto negotiation to complete........ done Using ethernet-controller@72000 device host 192.168.7.4 is alive ethernet-controller@72000 Waiting for PHY auto negotiation to complete........ done Using ethernet-controller@72000 device host 192.168.7.4 is alive ethernet-controller@72000 Waiting for PHY auto negotiation to complete........ done Using ethernet-controller@72000 device host 192.168.7.4 is alive
C:\Documents and Settings\Home\Desktop\ncat-portable-5.59BETA1>ncat -l -u -p 666 6 U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 gcc (Debian 10.2.1-6) 10.2.1 20210110 GNU ld (GNU Binutils for Debian) 2.35.2 Hit any key to stop autoboot: 2 0 C200_V1>boot boot Initializing devices... starting USB... Bus ehci@50000: USB EHCI 1.00 scanning bus ehci@50000 for devices... Use USB retry period from the environment: 15 second(s) 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Unknown command 'ide' - try 'help' Loading envs from usb 0... Failed to load '/boot/uEnv.txt' Loading envs from usb 1... Couldn't find partition usb 1:1 Can't set block device Loading envs from usb 2... Couldn't find partition usb 2:1 Can't set block device Loading envs from usb 3... Couldn't find partition usb 3:1 Can't set block device Loading envs from ide 0... Couldn't find partition ide 0:1 Can't set block device Loading envs from ide 1... Couldn't find partition ide 1:1 Can't set block device Loading envs from ide 2... Couldn't find partition ide 2:1 Can't set block device Loading envs from ide 3... Couldn't find partition ide 3:1 Can't set block device running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 9 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5576016 bytes read in 315 ms (16.9 MiB/s) loading uInitrd ... 9582895 bytes read in 528 ms (17.3 MiB/s) loading DTB /boot/dts/kirkwood-c200-v1.dtb ... 12173 bytes read in 13 ms (914.1 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.9.12-kirkwood-tld-1 Created: 2021-11-11 15:06:18 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5575952 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.9.12-kirkwood-tld-1 Created: 2021-11-11 15:06:26 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9582831 Bytes = 9.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Starting kernel ...
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 09:42AM |
Registered: 6 years ago Posts: 359 |
C200_V1>printenv printenv bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then boo tm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_a ddr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi ; sleep 3 bootdelay=10 bootdev=usb device=0:1 devices=usb ide disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-c200-v1.dtb ethact=ethernet-controller@72000 ethaddr=00:25:25:00:6d:f2 fdtcontroladdr=1fb53f00 if_netconsole=ping $serverip ipaddr=192.168.7.248 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $d tb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /b oot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /bo ot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi) nc_ready=1 ncip=192.168.7.4 partition=nand0,2 preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_ netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices ; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for di sknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.7.4 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; se tenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start"; se tenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $device s; do run init_$devtype; done uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done; uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_t ype $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo . .. envs loaded; fi usb_ready_retry=15 ver=U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 Environment size: 3043/131068 bytes C200_V1>boot
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 09:50AM |
Registered: 6 years ago Posts: 359 |
C:\Documents and Settings\Home\Desktop\ncat-portable-5.59BETA1>ncat -l -u -p 666 6 U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 gcc (Debian 10.2.1-6) 10.2.1 20210110 GNU ld (GNU Binutils for Debian) 2.35.2 Hit any key to stop autoboot: 6 0 C200_V1>printenv preboot printenv preboot preboot=run preboot_nc C200_V1>setenv preboot setenv preboot C200_V1>saveenv saveenv Saving Environment to NAND... Erasing NAND... Erasing at 0xc0000 -- 100% complete. Writing to NAND... OK OK C200_V1>reset reset resetting ...
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 12:28PM |
Registered: 6 years ago Posts: 359 |
U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 SoC: Kirkwood 88F6281_A1 Model: Ctera C200 V1 DRAM: 512 MiB NAND: 256 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial Net: eth0: ethernet-controller@72000 88E1116 Initialized on ethernet-controller@72000 Hit any key to stop autoboot: 0 Initializing devices... starting USB... Bus ehci@50000: USB EHCI 1.00 scanning bus ehci@50000 for devices... Use USB retry period from the environment: 15 second(s) 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Unknown command 'ide' - try 'help' Loading envs from usb 0... Failed to load '/boot/uEnv.txt' Loading envs from usb 1... Couldn't find partition usb 1:1 Can't set block device Loading envs from usb 2... Couldn't find partition usb 2:1 Can't set block device Loading envs from usb 3... Couldn't find partition usb 3:1 Can't set block device Loading envs from ide 0... Couldn't find partition ide 0:1 Can't set block device Loading envs from ide 1... Couldn't find partition ide 1:1 Can't set block device Loading envs from ide 2... Couldn't find partition ide 2:1 Can't set block device Loading envs from ide 3... Couldn't find partition ide 3:1 Can't set block device running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 10 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5576016 bytes read in 315 ms (16.9 MiB/s) loading uInitrd ... 9582895 bytes read in 528 ms (17.3 MiB/s) loading DTB /boot/dts/kirkwood-c200-v1.dtb ... 12173 bytes read in 13 ms (914.1 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.9.12-kirkwood-tld-1 Created: 2021-11-11 15:06:18 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5575952 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.9.12-kirkwood-tld-1 Created: 2021-11-11 15:06:26 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9582831 Bytes = 9.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image Loading Ramdisk to 1f22f000, end 1fb528ef ... OK Loading Device Tree to 1f229000, end 1f22ef8c ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.9.12-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Ctera C200 V1 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi) [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 492516K/524288K available (10240K kernel code, 1096K rwdata, 4144K rodata, 1024K init, 316K bss, 31772K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x790 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000054][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000845][ T0] Console: colour dummy device 80x30 [ 0.000900][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000929][ T0] pid_max: default: 32768 minimum: 301 [ 0.001349][ T0] LSM: Security Framework initializing [ 0.001503][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001532][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002909][ T0] CPU: Testing write buffer coherency: ok [ 0.004769][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005077][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.005394][ T1] rcu: Hierarchical SRCU implementation. [ 0.006708][ T1] devtmpfs: initialized [ 0.013693][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.013733][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.014009][ T1] xor: measuring software checksum speed [ 0.110120][ T1] arm4regs : 1088.800 MB/sec [ 0.210078][ T1] 8regs : 654.000 MB/sec [ 0.310081][ T1] 32regs : 950.800 MB/sec [ 0.310102][ T1] xor: using function: arm4regs (1088.800 MB/sec) [ 0.310127][ T1] prandom: seed boundary self test passed [ 0.314306][ T1] prandom: 100 self tests passed [ 0.314319][ T1] pinctrl core: initialized pinctrl subsystem [ 0.315868][ T1] NET: Registered protocol family 16 [ 0.316677][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.317731][ T1] audit: initializing netlink subsys (disabled) [ 0.319136][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.319497][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.319634][ T1] cpuidle: using governor ladder [ 0.319719][ T1] cpuidle: using governor menu [ 0.320272][ T1] Feroceon L2: Enabling L2 [ 0.320324][ T1] Feroceon L2: Cache support initialised. [ 0.336598][ T1] No ATAGs? [ 2.560060][ C0] random: fast init done [ 5.410422][ T1] raid6: int32x8 gen() 109 MB/s [ 5.580180][ T1] raid6: int32x8 xor() 69 MB/s [ 5.750253][ T1] raid6: int32x4 gen() 110 MB/s [ 5.920154][ T1] raid6: int32x4 xor() 72 MB/s [ 6.090243][ T1] raid6: int32x2 gen() 144 MB/s [ 6.260187][ T1] raid6: int32x2 xor() 85 MB/s [ 6.430155][ T1] raid6: int32x1 gen() 98 MB/s [ 6.600167][ T1] raid6: int32x1 xor() 59 MB/s [ 6.600179][ T1] raid6: using algorithm int32x2 gen() 144 MB/s [ 6.600188][ T1] raid6: .... xor() 85 MB/s, rmw enabled [ 6.600198][ T1] raid6: using intx1 recovery algorithm [ 6.600461][ T1] vgaarb: loaded [ 6.601033][ T1] SCSI subsystem initialized [ 6.601555][ T1] usbcore: registered new interface driver usbfs [ 6.601635][ T1] usbcore: registered new interface driver hub [ 6.601726][ T1] usbcore: registered new device driver usb [ 6.601955][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.601968][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.601997][ T1] PTP clock support registered [ 6.603637][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.142998][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.143106][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.154163][ T1] NET: Registered protocol family 2 [ 8.155037][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 8.155087][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.155157][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.155211][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 8.155440][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 8.155509][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.155541][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.155764][ T1] NET: Registered protocol family 1 [ 8.156526][ T1] RPC: Registered named UNIX socket transport module. [ 8.156540][ T1] RPC: Registered udp transport module. [ 8.156549][ T1] RPC: Registered tcp transport module. [ 8.156559][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.156574][ T1] PCI: CLS 0 bytes, default 32 [ 8.156892][ T1] Trying to unpack rootfs image as initramfs... [ 8.996238][ T1] Freeing initrd memory: 9360K [ 8.996414][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.007217][ T1] Initialise system trusted keyrings [ 9.007276][ T1] Key type blacklist registered [ 9.007501][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 9.007612][ T1] zbud: loaded [ 9.009074][ T1] NFS: Registering the id_resolver key type [ 9.009106][ T1] Key type id_resolver registered [ 9.009117][ T1] Key type id_legacy registered [ 9.009160][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.009180][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.009474][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 9.009998][ T1] fuse: init (API version 7.31) [ 9.010397][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.010610][ T1] orangefs_init: module version upstream loaded [ 9.010624][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 9.115431][ T1] async_tx: api initialized (async) [ 9.115457][ T1] Key type asymmetric registered [ 9.115467][ T1] Asymmetric key parser 'x509' registered [ 9.115526][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.115639][ T1] io scheduler bfq registered [ 9.314334][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.316317][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 9.316385][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 9.316425][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 9.316451][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 9.316754][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.316778][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.316799][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 9.316815][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.316830][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.316969][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.317003][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.318543][ T1] PCI: bus0: Fast back to back transfers disabled [ 9.318573][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.319842][ T1] PCI: bus1: Fast back to back transfers enabled [ 9.319869][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.320078][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 9.320097][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.320792][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.384694][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.387352][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.444679][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.447594][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.449023][ T1] printk: console [ttyS0] disabled [ 9.449116][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 10.399424][ T1] printk: console [ttyS0] enabled [ 10.413086][ T1] loop: module loaded [ 10.417803][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 10.427360][ T1] scsi host0: sata_mv [ 10.431901][ T1] scsi host1: sata_mv [ 10.436095][ T1] ata1: SATA max UDMA/133 irq 32 [ 10.440915][ T1] ata2: SATA max UDMA/133 irq 32 [ 10.447062][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 10.454238][ T1] nand: Samsung NAND 256MiB 3,3V 8-bit [ 10.459575][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 10.467957][ T1] Scanning device for bad blocks [ 10.525167][ T1] Bad eraseblock 490 at 0x000003d40000 [ 10.538453][ T1] Bad eraseblock 565 at 0x0000046a0000 [ 10.567435][ T1] Bad eraseblock 787 at 0x000006260000 [ 10.579677][ T1] Bad eraseblock 852 at 0x000006a80000 [ 10.602454][ T1] Bad eraseblock 1016 at 0x000007f00000 [ 10.669601][ T1] Bad eraseblock 1595 at 0x00000c760000 [ 10.696967][ T1] Bad eraseblock 1800 at 0x00000e100000 [ 10.704406][ T1] Bad eraseblock 1819 at 0x00000e360000 [ 10.713659][ T1] Bad eraseblock 1855 at 0x00000e7e0000 [ 10.739619][ T1] 2 cmdlinepart partitions found on MTD device orion_nand [ 10.746653][ T1] Creating 2 MTD partitions on "orion_nand": [ 10.752559][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 10.759765][ T1] 0x000000100000-0x000010000000 : "ubi" [ 10.768403][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 10.777094][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 10.788906][ T1] libphy: Fixed MDIO Bus: probed [ 10.795088][ T1] libphy: orion_mdio_bus: probed [ 10.816849][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.943689][ T88] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 10.953016][ T88] ata1.00: ATA-10: WDC WD40EZAZ-00SF3B0, 80.00A80, max UDMA/133 [ 10.960568][ T88] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 10.970633][ T88] ata1.00: configured for UDMA/133 [ 10.986190][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD40EZAZ-00S 0A80 PQ: 0 ANSI: 5 [ 10.996435][ T92] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB) [ 11.005442][ T92] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 11.011520][ T92] sd 0:0:0:0: [sda] Write Protect is off [ 11.017239][ T92] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.032065][ T92] sd 0:0:0:0: [sda] Attached SCSI disk [ 11.335277][ T90] ata2: SATA link down (SStatus 0 SControl F300) [ 11.504537][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:25:00:6d:f2 [ 11.514191][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.521475][ T1] ehci-pci: EHCI PCI platform driver [ 11.526728][ T1] ehci-orion: EHCI orion driver [ 11.531679][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.537956][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 11.546554][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 11.573681][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 11.580713][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09 [ 11.589745][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.597721][ T1] usb usb1: Product: EHCI Host Controller [ 11.603327][ T1] usb usb1: Manufacturer: Linux 5.9.12-kirkwood-tld-1 ehci_hcd [ 11.610774][ T1] usb usb1: SerialNumber: f1050000.ehci [ 11.616923][ T1] hub 1-0:1.0: USB hub found [ 11.621438][ T1] hub 1-0:1.0: 1 port detected [ 11.627004][ T1] usbcore: registered new interface driver usb-storage [ 11.634188][ T1] mousedev: PS/2 mouse device common for all mice [ 11.640795][ T1] i2c /dev entries driver [ 11.650910][ T1] rtc-s35390a 0-0030: registered as rtc0 [ 11.657572][ T1] rtc-s35390a 0-0030: setting system clock to 2022-01-10T18:15:29 UTC (1641838529) [ 11.668087][ T1] device-mapper: uevent: version 1.0.3 [ 11.673795][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com [ 11.683403][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 11.690772][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 11.698169][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 11.705655][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 11.712483][ T1] device-mapper: raid: Loading target version 1.15.1 [ 11.722167][ T1] hid: raw HID events driver (C) Jiri Kosina [ 11.728482][ T1] drop_monitor: Initializing network drop monitor service [ 11.736116][ T1] NET: Registered protocol family 10 [ 11.742535][ T1] Segment Routing with IPv6 [ 11.746979][ T1] RPL Segment Routing with IPv6 [ 11.751789][ T1] NET: Registered protocol family 17 [ 11.757279][ T1] Key type dns_resolver registered [ 11.762747][ T1] registered taskstats version 1 [ 11.767636][ T1] Loading compiled-in X.509 certificates [ 11.773262][ T1] zswap: loaded using pool lzo/zbud [ 11.778753][ T1] Key type ._fscrypt registered [ 11.783478][ T1] Key type .fscrypt registered [ 11.788193][ T1] Key type fscrypt-provisioning registered [ 11.796118][ T1] Key type big_key registered [ 11.831848][ T1] Key type encrypted registered [ 11.842783][ T1] Freeing unused kernel memory: 1024K [ 11.864583][ T1] Checked W+X mappings: passed, no W+X pages found [ 11.870988][ T1] Run /init as init process Loading, please wait... [ 11.993760][ T99] usb 1-1: new high-speed USB device number 2 using orion-ehci Starting version 241 [ 12.214341][ T99] usb 1-1: New USB device found, idVendor=0409, idProduct=005a, bcdDevice= 1.00 [ 12.223289][ T99] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 12.267513][ T99] hub 1-1:1.0: USB hub found [ 12.277457][ T99] hub 1-1:1.0: 4 ports detected [ 12.613741][ T99] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 12.729463][ T135] input: keys as /devices/platform/keys/input/input0 [ 12.774959][ T99] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5530, bcdDevice= 1.00 [ 12.793726][ T99] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.801778][ T99] usb 1-1.1: Product: Cruzer [ 12.834503][ T99] usb 1-1.1: Manufacturer: SanDisk [ 12.839501][ T99] usb 1-1.1: SerialNumber: 2005244411190D22FC1E [ 12.858853][ T99] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 12.878486][ T99] scsi host2: usb-storage 1-1.1:1.0 [ 13.353340][ T130] usbcore: registered new interface driver uas [ 13.924920][ T58] scsi 2:0:0:0: Direct-Access SanDisk Cruzer 1.02 PQ: 0 ANSI: 2 [ 13.939403][ T92] sd 2:0:0:0: [sdb] 7813120 512-byte logical blocks: (4.00 GB/3.73 GiB) [ 13.953868][ T92] sd 2:0:0:0: [sdb] Write Protect is off [ 13.960098][ T92] sd 2:0:0:0: [sdb] No Caching mode page found [ 13.966283][ T92] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 13.987411][ T92] sdb: sdb1 [ 14.006613][ T92] sd 2:0:0:0: [sdb] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 25.316055][ T153] process '/usr/bin/fstype' started with executable stack Begin: Will now check root file system ... fsck from util-linux 2.33.1 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sdb1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 30.497254][ T162] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem [ 30.535316][ T162] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [ ok ] Synthesizing the initial hotplug events (devices)...done. [....] Waiting for /dev to be fully populated...[ 33.790367][ T352] systemd-udevd[352]: Using default interface naming scheme 'v240'. [ 33.903361][ T352] systemd-udevd[352]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 34.008241][ T370] orion_wdt: Initial timeout 21 sec [ 34.319749][ T381] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 34.327266][ C0] random: crng init done [ 34.414088][ T381] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 34.567472][ T353] marvell-cesa f1030000.crypto: CESA device successfully registered [ 34.775052][ T349] systemd-udevd[349]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 37.048839][ T570] EXT4-fs (sdb1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sdb1 e2fsck 1.44.5 (15-Dec-2018) rootfs: clean, 17950/244320 files, 520048/976384 blocks . ok [ 37.374751][ T596] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:25:00:6d:f2 Sending on LPF/eth0/00:25:25:00:6d:f2 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 [ 44.776008][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19 DHCPOFFER of 192.168.7.248 from 192.168.7.1 DHCPREQUEST for 192.168.7.248 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.7.248 from 192.168.7.1 bound to 192.168.7.248 -- renewal in 40532 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... [ ok ] Setting sensors limits...done. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1356 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1383 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 debian ttyS0 debian login: root Password: Last login: Mon Jan 10 07:47:07 PST 2022 on ttyS0 Linux debian 5.9.12-kirkwood-tld-1 #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# df
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 12:46PM |
Registered: 6 years ago Posts: 359 |
U-Boot 2021.10-tld-0.3 (Jan 07 2022 - 15:08:00 -0800)Ctera C200 V1 SoC: Kirkwood 88F6281_A1 Model: Ctera C200 V1 DRAM: 512 MiB NAND: 256 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial Net: eth0: ethernet-controller@72000 88E1116 Initialized on ethernet-controller@72000 Hit any key to stop autoboot: 0 C200_V1>sata init C200_V1>sata info Device 0: Model: WDC WD40EZAZ-00SF3B0 Firm: 80.00A80 Ser#: WD-WX22D616S0PD Type: Hard Disk Supports 48-bit addressing Capacity: 3815447.8 MB = 3726.0 GB (7814037168 x 512) Failed to wait for completion on port 1 ATA operation timed out Device 1: Model: Firm: Ser#: Type: Hard Disk Capacity: not available C200_V1>ext2load sata 0 0x800000 /boot/uImage 5576016 bytes read in 89 ms (59.7 MiB/s) C200_V1>ext2load sata 0 0x1100000 /boot/uInitrd 9582895 bytes read in 81 ms (112.8 MiB/s) C200_V1>ext2load sata 0 0x1c00000 /boot/dts/kirkwood-c200-v1.dtb 12173 bytes read in 29 ms (409.2 KiB/s) C200_V1>bootm 0x800000 0x1100000 0x1c00000 ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.9.12-kirkwood-tld-1 Created: 2021-11-11 15:06:18 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5575952 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.9.12-kirkwood-tld-1 Created: 2021-11-11 15:06:26 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9582831 Bytes = 9.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image Loading Ramdisk to 1f22f000, end 1fb528ef ... OK Loading Device Tree to 1f229000, end 1f22ef8c ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.9.12-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Ctera C200 V1 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi) [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 492516K/524288K available (10240K kernel code, 1096K rwdata, 4144K rodata, 1024K init, 316K bss, 31772K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x790 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000010][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000054][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000848][ T0] Console: colour dummy device 80x30 [ 0.000904][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000933][ T0] pid_max: default: 32768 minimum: 301 [ 0.001356][ T0] LSM: Security Framework initializing [ 0.001512][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001543][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002928][ T0] CPU: Testing write buffer coherency: ok [ 0.004788][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005097][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.005414][ T1] rcu: Hierarchical SRCU implementation. [ 0.006724][ T1] devtmpfs: initialized [ 0.013706][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.013746][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.014016][ T1] xor: measuring software checksum speed [ 0.110119][ T1] arm4regs : 1088.800 MB/sec [ 0.210077][ T1] 8regs : 654.000 MB/sec [ 0.310077][ T1] 32regs : 950.800 MB/sec [ 0.310099][ T1] xor: using function: arm4regs (1088.800 MB/sec) [ 0.310123][ T1] prandom: seed boundary self test passed [ 0.314302][ T1] prandom: 100 self tests passed [ 0.314314][ T1] pinctrl core: initialized pinctrl subsystem [ 0.315854][ T1] NET: Registered protocol family 16 [ 0.316664][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.317717][ T1] audit: initializing netlink subsys (disabled) [ 0.319127][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.319485][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.319624][ T1] cpuidle: using governor ladder [ 0.319709][ T1] cpuidle: using governor menu [ 0.320260][ T1] Feroceon L2: Enabling L2 [ 0.320311][ T1] Feroceon L2: Cache support initialised. [ 0.336589][ T1] No ATAGs? [ 2.560059][ C0] random: fast init done [ 5.410310][ T1] raid6: int32x8 gen() 109 MB/s [ 5.580231][ T1] raid6: int32x8 xor() 69 MB/s [ 5.750201][ T1] raid6: int32x4 gen() 109 MB/s [ 5.920148][ T1] raid6: int32x4 xor() 72 MB/s [ 6.090187][ T1] raid6: int32x2 gen() 140 MB/s [ 6.260143][ T1] raid6: int32x2 xor() 85 MB/s [ 6.430227][ T1] raid6: int32x1 gen() 98 MB/s [ 6.600194][ T1] raid6: int32x1 xor() 60 MB/s [ 6.600207][ T1] raid6: using algorithm int32x2 gen() 140 MB/s [ 6.600216][ T1] raid6: .... xor() 85 MB/s, rmw enabled [ 6.600225][ T1] raid6: using intx1 recovery algorithm [ 6.600486][ T1] vgaarb: loaded [ 6.601068][ T1] SCSI subsystem initialized [ 6.601596][ T1] usbcore: registered new interface driver usbfs [ 6.601679][ T1] usbcore: registered new interface driver hub [ 6.601769][ T1] usbcore: registered new device driver usb [ 6.602000][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.602013][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.602043][ T1] PTP clock support registered [ 6.603685][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.143044][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.143151][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.154185][ T1] NET: Registered protocol family 2 [ 8.155064][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 8.155114][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.155185][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.155238][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 8.155461][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 8.155529][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.155561][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.155786][ T1] NET: Registered protocol family 1 [ 8.156553][ T1] RPC: Registered named UNIX socket transport module. [ 8.156567][ T1] RPC: Registered udp transport module. [ 8.156577][ T1] RPC: Registered tcp transport module. [ 8.156586][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.156602][ T1] PCI: CLS 0 bytes, default 32 [ 8.156923][ T1] Trying to unpack rootfs image as initramfs... [ 8.996282][ T1] Freeing initrd memory: 9360K [ 8.996457][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.007264][ T1] Initialise system trusted keyrings [ 9.007324][ T1] Key type blacklist registered [ 9.007557][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 9.007665][ T1] zbud: loaded [ 9.009135][ T1] NFS: Registering the id_resolver key type [ 9.009170][ T1] Key type id_resolver registered [ 9.009181][ T1] Key type id_legacy registered [ 9.009227][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.009247][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.009542][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 9.010066][ T1] fuse: init (API version 7.31) [ 9.010465][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.010678][ T1] orangefs_init: module version upstream loaded [ 9.010692][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 9.111546][ T1] async_tx: api initialized (async) [ 9.111571][ T1] Key type asymmetric registered [ 9.111582][ T1] Asymmetric key parser 'x509' registered [ 9.111642][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.111758][ T1] io scheduler bfq registered [ 9.310451][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.312431][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 9.312500][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 9.312540][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 9.312567][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 9.312870][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.312893][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.312913][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 9.312929][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.312944][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.313083][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.313117][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.314711][ T1] PCI: bus0: Fast back to back transfers disabled [ 9.314742][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.316018][ T1] PCI: bus1: Fast back to back transfers enabled [ 9.316047][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.316255][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 9.316274][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.316973][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.374746][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.377407][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.434732][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.437629][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.439058][ T1] printk: console [ttyS0] disabled [ 9.439152][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 10.389454][ T1] printk: console [ttyS0] enabled [ 10.403123][ T1] loop: module loaded [ 10.407841][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 10.417410][ T1] scsi host0: sata_mv [ 10.421956][ T1] scsi host1: sata_mv [ 10.426145][ T1] ata1: SATA max UDMA/133 irq 32 [ 10.430962][ T1] ata2: SATA max UDMA/133 irq 32 [ 10.437110][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 10.444285][ T1] nand: Samsung NAND 256MiB 3,3V 8-bit [ 10.449623][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 10.458005][ T1] Scanning device for bad blocks [ 10.515159][ T1] Bad eraseblock 490 at 0x000003d40000 [ 10.528448][ T1] Bad eraseblock 565 at 0x0000046a0000 [ 10.557433][ T1] Bad eraseblock 787 at 0x000006260000 [ 10.569663][ T1] Bad eraseblock 852 at 0x000006a80000 [ 10.592441][ T1] Bad eraseblock 1016 at 0x000007f00000 [ 10.659596][ T1] Bad eraseblock 1595 at 0x00000c760000 [ 10.686946][ T1] Bad eraseblock 1800 at 0x00000e100000 [ 10.694370][ T1] Bad eraseblock 1819 at 0x00000e360000 [ 10.703609][ T1] Bad eraseblock 1855 at 0x00000e7e0000 [ 10.729587][ T1] 2 cmdlinepart partitions found on MTD device orion_nand [ 10.736618][ T1] Creating 2 MTD partitions on "orion_nand": [ 10.742526][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 10.749729][ T1] 0x000000100000-0x000010000000 : "ubi" [ 10.758366][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 10.767054][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 10.778860][ T1] libphy: Fixed MDIO Bus: probed [ 10.785030][ T1] libphy: orion_mdio_bus: probed [ 10.807101][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.933737][ T88] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 10.943064][ T88] ata1.00: ATA-10: WDC WD40EZAZ-00SF3B0, 80.00A80, max UDMA/133 [ 10.950615][ T88] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 10.960682][ T88] ata1.00: configured for UDMA/133 [ 10.976239][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD40EZAZ-00S 0A80 PQ: 0 ANSI: 5 [ 10.986484][ T92] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB) [ 10.995491][ T92] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 11.001567][ T92] sd 0:0:0:0: [sda] Write Protect is off [ 11.007290][ T92] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.069262][ T92] sda: sda1 [ 11.074269][ T92] sd 0:0:0:0: [sda] Attached SCSI disk [ 11.325326][ T90] ata2: SATA link down (SStatus 0 SControl F300) [ 11.494586][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:25:00:6d:f2 [ 11.504225][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.511505][ T1] ehci-pci: EHCI PCI platform driver [ 11.516759][ T1] ehci-orion: EHCI orion driver [ 11.521701][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.527977][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 11.536569][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 11.563730][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 11.570748][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09 [ 11.579782][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.587760][ T1] usb usb1: Product: EHCI Host Controller [ 11.593365][ T1] usb usb1: Manufacturer: Linux 5.9.12-kirkwood-tld-1 ehci_hcd [ 11.600813][ T1] usb usb1: SerialNumber: f1050000.ehci [ 11.606959][ T1] hub 1-0:1.0: USB hub found [ 11.611490][ T1] hub 1-0:1.0: 1 port detected [ 11.617064][ T1] usbcore: registered new interface driver usb-storage [ 11.624260][ T1] mousedev: PS/2 mouse device common for all mice [ 11.630853][ T1] i2c /dev entries driver [ 11.640993][ T1] rtc-s35390a 0-0030: registered as rtc0 [ 11.647650][ T1] rtc-s35390a 0-0030: setting system clock to 2022-01-10T18:44:54 UTC (1641840294) [ 11.658174][ T1] device-mapper: uevent: version 1.0.3 [ 11.663861][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com [ 11.673493][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 11.680862][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 11.688262][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 11.695729][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 11.702557][ T1] device-mapper: raid: Loading target version 1.15.1 [ 11.712283][ T1] hid: raw HID events driver (C) Jiri Kosina [ 11.718589][ T1] drop_monitor: Initializing network drop monitor service [ 11.726215][ T1] NET: Registered protocol family 10 [ 11.732631][ T1] Segment Routing with IPv6 [ 11.737078][ T1] RPL Segment Routing with IPv6 [ 11.741888][ T1] NET: Registered protocol family 17 [ 11.747388][ T1] Key type dns_resolver registered [ 11.752856][ T1] registered taskstats version 1 [ 11.757747][ T1] Loading compiled-in X.509 certificates [ 11.763366][ T1] zswap: loaded using pool lzo/zbud [ 11.768857][ T1] Key type ._fscrypt registered [ 11.773587][ T1] Key type .fscrypt registered [ 11.778302][ T1] Key type fscrypt-provisioning registered [ 11.786198][ T1] Key type big_key registered [ 11.821829][ T1] Key type encrypted registered [ 11.832767][ T1] Freeing unused kernel memory: 1024K [ 11.854630][ T1] Checked W+X mappings: passed, no W+X pages found [ 11.861036][ T1] Run /init as init process Loading, please wait... [ 11.983816][ T99] usb 1-1: new high-speed USB device number 2 using orion-ehci Starting version 241 [ 12.204356][ T99] usb 1-1: New USB device found, idVendor=0409, idProduct=005a, bcdDevice= 1.00 [ 12.213299][ T99] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 12.257779][ T99] hub 1-1:1.0: USB hub found [ 12.267271][ T99] hub 1-1:1.0: 4 ports detected [ 12.749469][ T132] input: keys as /devices/platform/keys/input/input0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 24.636689][ T148] process '/usr/bin/fstype' started with executable stack Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1 rootfs: clean, 19392/244195328 files, 15865769/976754385 blocks done. [ 26.669402][ T158] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [....] Synthesizing the initial hotplug events (devices)...[ 30.555628][ C0] random: crng init done done. [....] Waiting for /dev to be fully populated...[ 30.776864][ T365] systemd-udevd[365]: Using default interface naming scheme 'v240'. [ 30.895868][ T365] systemd-udevd[365]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.081746][ T377] orion_wdt: Initial timeout 21 sec [ 31.181706][ T347] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 31.566375][ T348] systemd-udevd[348]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.658656][ T375] marvell-cesa f1030000.crypto: CESA device successfully registered done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 33.944332][ T566] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [info] Loading kernel module lm63. [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:25:00:6d:f2 Sending on LPF/eth0/00:25:25:00:6d:f2 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 [ 41.657806][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPOFFER of 192.168.7.248 from 192.168.7.1 DHCPREQUEST for 192.168.7.248 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.7.248 from 192.168.7.1 bound to 192.168.7.248 -- renewal in 32825 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... [ ok ] Setting sensors limits...done. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1357 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1384 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting fancontrol; run pwmconfig first. ... (warning). [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 debian ttyS0 debian login: root Password: Last login: Mon Jan 10 10:36:47 PST 2022 on ttyS0 Linux debian 5.9.12-kirkwood-tld-1 #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# df Filesystem 1K-blocks Used Available Use% Mounted on udev 246256 0 246256 0% /dev tmpfs 50292 152 50140 1% /run /dev/sda1 3844640564 1086104 3843538076 1% / tmpfs 5120 0 5120 0% /run/lock tmpfs 100580 0 100580 0% /dev/shm tmpfs 251448 0 251448 0% /tmp root@debian:~# ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.7.248 netmask 255.255.255.0 broadcast 192.168.7.255 ether 00:25:25:00:6d:f2 txqueuelen 1000 (Ethernet) RX packets 17 bytes 2141 (2.0 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 16 bytes 2004 (1.9 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 35 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 loop txqueuelen 1000 (Local Loopback) RX packets 2 bytes 140 (140.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 2 bytes 140 (140.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@debian:~#
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 01:01PM |
Registered: 6 years ago Posts: 359 |
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 04:14PM |
Admin Registered: 12 years ago Posts: 17,933 |
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 04:17PM |
Admin Registered: 12 years ago Posts: 17,933 |
mtdparts=mtdparts=orion_nand:2M(u-boot),-(ubi)
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 07:26PM |
Registered: 6 years ago Posts: 359 |
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 10, 2022 11:30PM |
Admin Registered: 12 years ago Posts: 17,933 |
Re: Debian on Kirkwood Box Ctera C200 v1 with 512MB memory and two SATA bays for 3.5" Hard Drives January 11, 2022 12:48PM |
Registered: 6 years ago Posts: 359 |