Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 28, 2021 03:03PM |
Registered: 2 years ago Posts: 8 |
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 28, 2021 04:49PM |
Admin Registered: 13 years ago Posts: 18,821 |
printenvAnd then boot as you have been doing.
cat /proc/mtd
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 29, 2021 01:11AM |
Registered: 2 years ago Posts: 8 |
BootROM 1.08 Booting from NAND flash lHigh speed PHY - Version: 2.1.2 (COM-PHY-V20) Update PEX Device ID 0x67100 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver 4.5.0 DDR3 Training Sequence - Ended Successfully Status = MV_OK BootROM: Image checksum verification PASSED ** LOADER ** U-Boot 2011.12 (Dec 24 2013 - 20:21:45) Marvell version: v2011.12 2013_Q1.2 (ALPHA U-BOOT : 1.0) Board: RD-88F6710_ALpha_KingsCanyon SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB l Map: Code: 0x1fef5000:0x1ff9faac BSS: 0x1ffef784 Stack: 0x1f9f4ef8 Heap: 0x1f9f5000:0x1fef5000 NAND: flash id : daad 256 MiB MMC: MRVL_MMC: 0 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: Bad block at 0x000005a60000 PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0 PEX 0.1(1): Detected No Link. FPU not initialized USB 0: Host Mode USB 1: Host Mode Modules/Interfaces Detected: RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Not Marvell PHY id1 ffff id2 ffff Enable HD1 Enable HD2 Net: egiga1 Warning: egiga1 MAC addresses don't match: Address in SROM is 00:50:43:02:00:00 Address in environment is 00:50:43:02:02:00 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x500000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux-3.2.40 Created: 2018-11-16 4:28:51 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3115296 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Ramdisk Created: 2018-12-20 7:27:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 2104783 Bytes = 2 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. mInitializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 3.2.40 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 Fri Nov 16 12:28:49 CST 2018 CPU: Marvell PJ4Bv7 Processor [561f5811] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache Machine: Marvell Armada-370 Using UBoot passing parameters structure >>>>>>>Tag MAC 00:02:02:43:50:00 >>>>>>>Tag MAC 00:00:02:43:50:00 Memory policy: ECC disabled, Data cache writealloc Built 1 zonelists in Zone order, mobility grouping off. Total pages: 16368 Kernel command line: root=/dev/ram console=ttyS0,115200 max_loop=32 PID hash table entries: 2048 (order: -2, 8192 bytes) Dentry cache hash table entries: 65536 (order: 3, 262144 bytes) Inode-cache hash table entries: 32768 (order: 2, 131072 bytes) allocated 262144 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 512MB = 512MB total Memory: 506528k/506528k available, 17760k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff8000 ( 32 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xa0800000 - 0xfa800000 (1440 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) modules : 0x7f000000 - 0x80000000 ( 16 MB) .text : 0x80008000 - 0x805b8000 (5824 kB) .init : 0x805b8000 - 0x805e8000 ( 192 kB) .data : 0x805e8000 - 0x80620a20 ( 227 kB) .bss : 0x80620a44 - 0x8066aa38 ( 296 kB) NR_IRQS:256 a370_time_init sched_clock: 32 bits at 600MHz, resolution 1ns, wraps every 7158ms Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 4096 Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices CPU: Testing write buffer coherency: ok hw perfevents: no hardware support available devtmpfs: initialized xor: measuring software checksum speed arm4regs : 169.600 MB/sec 8regs : 166.400 MB/sec 32regs : 166.400 MB/sec xor: using function: arm4regs (169.600 MB/sec) NET: Registered protocol family 16 L0 cache Enabled Speculative Prefetch Disabled Aurora L2 Cache Enabled Support IO coherency. Enable DLB and DRAM write coalescing CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 512MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable DEVICE_CS0 ....base f2000000, size 32MB DEVICE_CS1 ....no such DEVICE_CS2 ....no such DEVICE_CS3 ....no such PEX0_MEM ....base e0000000, size 32MB PEX0_IO ....base f1100000, size 1MB PEX1_MEM ....base e2000000, size 32MB PEX1_IO ....base f1200000, size 1MB INTER_REGS ....base f1000000, size 1MB DMA_UART ....no such SPI_CS0 ....base f0000000, size 16MB SPI_CS1 ....no such SPI_CS2 ....no such SPI_CS3 ....no such SPI_CS4 ....no such SPI_CS5 ....no such SPI_CS6 ....no such SPI_CS7 ....no such BOOT_ROM_CS ....no such DEV_BOOTCS ....base f5000000, size 16MB PMU_SCRATCHPAD ....no such CRYPT0_ENG ....base c8010000, size 64KB Marvell Armada370 Board-- RD-88F6710_Alpha Soc: MV6710 A1 LE LSP version: linux-3.2.y-2013_Q1.2p2 (32KB SW Page Size) Detected Tclk 200000000, SysClk 600000000, FabricClk 600000000 Marvell USB EHCI Host controller #0: 90017920 Marvell USB EHCI Host controller #1: 90017720 PCI: bus0: Fast back to back transfers disabled PCI: bus1: Fast back to back transfers enabled pci 0000:00:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] pci 0000:00:00.0: BAR 0: set to [mem 0xe0000000-0xe0001fff 64bit] (PCI address [0xe0000000-0xe0001fff]) bio: create slab <bio-0> at 0 raid6: int32x1 340 MB/s raid6: int32x2 353 MB/s raid6: int32x4 275 MB/s raid6: int32x8 280 MB/s raid6: using algorithm int32x2 (353 MB/s) SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource armada370_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 8192 (order: 0, 32768 bytes) TCP established hash table entries: 16384 (order: 2, 131072 bytes) TCP bind hash table entries: 16384 (order: 1, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered UDP hash table entries: 2048 (order: 0, 32768 bytes) UDP-Lite hash table entries: 2048 (order: 0, 32768 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 2016K CESA test started: bufNum = 1, bufSize = 20000 Cesa Test Start: pMbufSrc=90024060, pFragsSrc=90272000, pMbufDst=90023860, pFragsDst=90270000 mvCesaInit: channels=1, session=32, queue=256 cesadev_init(805bfbe4) Armada XP hwmon thermal sensor initialized. Initializing Armada-XP CPU power management (WFI) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 8192 (order 0, 32768 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.17) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 992 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Initializing ths8200_init Initializing dove_adi9889_init mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver mv_xor mv_xor.0: Marvell XOR: ( xor ) mv_xor mv_xor.1: Marvell XOR: ( xor ) mv_xor mv_xor.2: Marvell XOR: ( cpy ) mv_xor mv_xor.3: Marvell XOR: ( fill cpy ) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 41) is a 16550A console [ttyS0] enabled serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 42) is a 16550A brd: module loaded loop: module loaded sata_mv sata_mv.0: slots 32 ports 2 scsi0 : sata_mv scsi1 : sata_mv ata1: SATA max UDMA/133 irq 55 ata2: SATA max UDMA/133 irq 55 armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC flash read_id : daad NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: bad block at 0x000005a60000 Creating 7 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "u-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "ramdisk" 0x000000f00000-0x00000d800000 : "image.cfs" 0x00000dd00000-0x00000ec00000 : "rescue firmware" 0x00000ec00000-0x000010000000 : "config" 0x00000d800000-0x00000dd00000 : "reserve" mv_eth_probe: port_mask=0x3, cpu_mask=0x1 o 2 Giga ports supported o SKB recycle supported (Enabled) o NETA acceleration mode 1 o RX Queue support: 1 Queues * 128 Descriptors o TX Queue support: 1 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Loading network interface(s) o Warning: GbE port 0 is not connected to PHY/RGMII/Switch, skip initialization o Port 1 is connected to Linux netdevice giga p=1: mtu=1500, mac=900b1e6c o egiga0, ifindex = 2, GbE port = 1 sky2: driver version 1.30 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.0: Marvell Orion EHCI ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.0: irq 45, io base 0xfbb50100 ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_marvell ehci_marvell.1: Marvell Orion EHCI ehci_marvell ehci_marvell.1: new USB bus registered, assigned bus number 2 ehci_marvell ehci_marvell.1: irq 46, io base 0xfbb51100 ehci_marvell ehci_marvell.1: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci_hcd 0000:00:00.0: xHCI Host Controller xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 3 xhci_hcd 0000:00:00.0: irq 58, io mem 0xe0000000 xhci_hcd 0000:00:00.0: Failed to enable MSI-X xhci_hcd 0000:00:00.0: failed to allocate MSI entry hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected xhci_hcd 0000:00:00.0: xHCI Host Controller xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 ata1: SATA link down (SStatus 0 SControl F300) device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com cpuidle: using governor ladder cpuidle: using governor menu TCP cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 registered taskstats version 1 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata2.00: ATA-9: WDC WD30EZRX-00DC0B0, 80.00A80, max UDMA/133 ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD30EZRX-00D 80.0 PQ: 0 ANSI: 5 sd 1:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 1:0:0:0: [sda] 4096-byte physical blocks sd 1:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sd 1:0:0:0: [sda] Attached SCSI disk md: Skipping autodetection of RAID arrays. (raid=autodetect will force) RAMDISK: gzip image found at block 0 VFS: Mounted root (ext2 filesystem) on device 1:0. Freeing init memory: 192K init started: BusyBox v1.20.2 (2014-10-30 15:26:14 CST) starting pid 478, tty '': '/etc/rc.sh' ** Mounting /etc/fstab umount: can't umount /proc: Invalid argument umount: can't umount /usr/local/modules: Invalid argument sh: hotPlug.sh: not found sh: can't open '/usr/sbin/pre_usb.sh' sh: can't open '/usr/sbin/pre_usb.sh' sh: can't open '/usr/sbin/pre_usb.sh' sh: can't open '/usr/sbin/pre_usb.sh' UBI: attaching mtd5 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 58585 UBI: attached mtd5 to ubi0 UBI: MTD device name: "config" UBI: MTD device size: 20 MiB UBI: number of good PEBs: 152 UBI: number of bad PEBs: 8 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 22 UBI: total number of reserved PEBs: 130 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 521/385 UBI: image sequence number: -913937646 UBI: background thread "ubi_bgt0d" started, PID 502 UBI device number 0, total 152 LEBs (19300352 bytes, 18.4 MiB), available 22 LEBs (2793472 bytes, 2.7 MiB), LEB size 126976 bytes (124.0 KiB) UBIFS: mounted UBI device 0, volume 0, name "config" UBIFS: file system size: 14602240 bytes (14260 KiB, 13 MiB, 115 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 689699 bytes (673 KiB) umount: can't umount /usr/local/tmp/image.cfs: No such file or directory rm: can't remove '/usr/local/tmp/image.cfs': No such file or directory umount: can't umount /usr/local/tmp: Invalid argument first good block is 0 image len = 100331520 , image checksum = 77ba3883 umount: can't umount /usr/local/tmp: Invalid argument dump image checksum=77ba3883 mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules cp: can't stat '/tmp1/*': No such file or directory ln: /lib/./liblber-2.4.so.2.5.6: File exists ln: /lib/./libminiupnpc.so: File exists ln: /lib/./libnatpmp.so: File exists ln: /lib/./libpam.so.0.81.6: File exists ln: /usr/local/sbin/alert_email_config.sh: File exists ln: /usr/sbin/language.sh: File exists dev.raid.speed_limit_max = 1000 jnl: driver (lke_9.0.0 lke_9.0.0_r239626_b47, LBD=ON) loaded at 7f000000 ufsd: module license 'Commercial product' taints kernel. Disabling lock debugging due to kernel taint ufsd:: trace mask set to 0000000f ufsd: driver (lke_9.0.0 lke_9.0.0_r239626_b47, LBD=ON, acl, ioctl, bdi, sd2(0), fua, bz, tr) loaded at 7f020000 NTFS support included Hfs+/HfsJ support included optimized: speed Build_for__WD_Kings_Canyon_k3.2.40_32k_hybrid_2014-07-28_lke_9.0.0_r239626_b47 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> lrwxrwxrwx 1 root 0 17 Jan 1 00:00 /usr/sbin//raid_config -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jan 1 00:00 /usr/sbin//raid_expand -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jan 1 00:00 /usr/sbin//raid_expand_disks -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jan 1 00:00 /usr/sbin//raid_update_info -> /usr/sbin/diskmgr hardware init first good block is 0 mtd check v1.06.06032015 config mtd type is UBIFS device = /usr/local/config Total size = 12500 Kbytes Used size = 552 Kbytes Free size = 11948 Kbytes percentage = 5 /usr/local/config free size is 12234752 ** copy config files *** Copy orion.db from flash **** cp: can't stat '/usr/local/modules/files/fan_temperature.txt': No such file or directory *** symlink onbrd.ini from flash **** /etc/sysinit.d/wdlog: line 13: /etc/system.conf: No such file or directory ** set loopback interface UBI: attaching mtd6 to ubi1 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 74 UBI: attached mtd6 to ubi1 UBI: MTD device name: "reserve" UBI: MTD device size: 5 MiB UBI: number of good PEBs: 40 UBI: number of bad PEBs: 0 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 40 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/2 UBI: image sequence number: 1575340750 UBI: background thread "ubi_bgt1d" started, PID 2454 UBI device number 1, total 40 LEBs (5079040 bytes, 4.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) UBIFS: mounted UBI device 1, volume 0, name "reserve" UBIFS: file system size: 3174400 bytes (3100 KiB, 3 MiB, 25 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 149934 bytes (146 KiB) UBIFS: un-mount UBI device 1, volume 0 first good block is 0 mac1 = 00:90:A9:E3:4F:01 lan0:ifconfig egiga0 hw ether 00:90:A9:E3:4F:01 egiga0: mac address changed egiga0: link up egiga0: started set lan0 speed Model ID : Zion first good block is 0 Zion ln: /usr/local/model/web/pages/images/./icon: File exists first good block is 0 hidden encryption: 1 old firmware ver:2.12.127.1219.2018 new firmware ver:2.12.127.1219.2018 rm: can't remove '/tmp/fix_wd_config': No such file or directory *** execute rc.init.sh awk: /var/run/udhcpc0.pid: No such file or directory udhcpc (v1.20.2) started cat: can't open '/tmp/setip.0': No such file or directory Sending discover... Sending select for 10.10.10.248... Lease of 10.10.10.248 obtained, lease time 86400 deleting routers route: SIOCDELRT: No such process killall: crond: no process killed crond[2703]: crond: crond (busybox 1.20.2) started, log level 8 RTNETLINK answers: Operation not supported RTNETLINK answers: Operation not supported call load_module network Cannot get device settings: No such device Cannot get wake-on-lan settings: No such device Cannot get message level: No such device Cannot get link status: No such device Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 10.10.10.248 port = 49152 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://10.10.10.248:49152/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized Advertisements Sent crond[2778]: crond: crond (busybox 1.20.2) started, log level 8 --1970-01-01 00:00:42-- http://download.wdc.com/nas/WDMyCloudEX2_HDD_Blacklist.xml Resolving download.wdc.com... 34.216.127.94, 35.165.176.197, 34.209.94.17, ... Connecting to download.wdc.com|34.216.127.94|:80... Cannot get device settings: No such device Cannot get wake-on-lan settings: No such device Cannot get message level: No such device Cannot get link status: No such device Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 10.10.10.248 port = 49153 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://10.10.10.248:49153/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized sh: you need to specify whom to kill connected. HTTP request sent, awaiting response... Advertisements Sent 200 OK Length: 256 [text/xml] Saving to: '/tmp/temp_list.xml' 100%[======================================>] 256 --.-K/s in 0s 1970-01-01 00:00:43 (5.23 MB/s) - '/tmp/temp_list.xml' saved [256/256] *** Copy CacheVolume data from flash **** *** set Time Zone **** $Usage: apache {start|stop|restart} {web/dav} Thu Jan 1 01:00:44 CET 1970 *** get Time from rtc and set it into system **** rtc: RTC time = 2021/12/27 Mon 16:9:34 Mon Dec 27 17:09:34 CET 2021 Set Date & time : sntp -K /dev/null -S -r time.windows.com sntp 4.2.8@1.3265 Fri Jan 9 06:42:54 UTC 2015 (8) 2021-12-27 17:09:34.239680 (-0100) +0.944710 +/- 0.655436 time.windows.com 20.101.57.9 s3 NTP Server connected successfully!!! Module IPC SERVER Version:(1.00.20090706) ads=0 created mail daemon thread 0 POWER ON DEVICE!! md0 state is Up_Send_Ctl : Can not find specified command "ErrStatus" restart sysinfod... sysinfod: full update begin... rtc: system time: 2021/12/27 Mon 16:9:40 cat: can't open '/tmp/hw_detect_sata': No such file or directory sysinfod: disk connected: previous=0xffffffff, now=0x0 --2021-12-27 17:09:40-- http://download.wdc.com/nas/WDMyCloudEX2_HDD_Blacklist.xml Resolving download.wdc.com... 34.216.118.116, 34.209.94.17, 34.210.173.110, ... Connecting to download.wdc.com|34.216.118.116|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 256 [text/xml] Saving to: '/tmp/temp_list.xml' 100%[======================================>] 256 --.-K/s in 0s 2021-12-27 17:09:41 (7.31 MB/s) - '/tmp/temp_list.xml' saved [256/256] sysinfod: Disk2(sda) detected. Starting system message bus Loading x_tables.ko Loading nf_conntrack.ko nf_conntrack version 0.5.0 (7949 buckets, 31796 max) Loading xt_conntrack.ko Loading xt_state.ko Loading xt_tcpudp.ko Loading xt_recent.ko Loading xt_limit.ko Loading ip_tables.ko ip_tables: (C) 2000-2006 Netfilter Core Team Loading iptable_filter.ko Loading nf_defrag_ipv4.ko Loading nf_conntrack_ipv4.ko Loading ipt_LOG.ko PHY_LAN_NUMBER=1 BOND_ENABLE=0 VLAN0_ENABLE=0 VLAN1_ENABLE=0 --2021-12-27 17:09:43-- http://download.wdc.com/apps/WDMyCloudMirror/WDMyCloudMirror.xml Resolving download.wdc.com... I/O warning : failed to load external entity "/var/www/xml/internal_backup.xml" 34.216.118.116, 44.226.106.124, 44.229.153.191, ... Connecting to download.wdc.com|34.216.118.116|:80... /usr/local/modules/script/system_init: line 1040: /mnt/tmp6/ibuki/avahi_tm_serv: not found cat: can't open '/var/run/traceroute_wd.pid': No such file or directory ash: you need to specify whom to kill killall: traceroute: no process killed connected. HTTP request sent, awaiting response... 200 OK Length: 12025 (12K) [text/xml] Saving to: '/var/www/xml/app_info.xml' 100%[======================================>] 12,025 --.-K/s in 0.001s 2021-12-27 17:09:44 (18.3 MB/s) - '/var/www/xml/app_info.xml' saved [12025/12025] I/O warning : failed to load external entity "/var/www/xml/app_update.xml" 3077 root 4096 S avahi-daemon: running [WDMyCloudMirror.local] sysinfod: disk connected: previous=0x0, now=0x2 --2021-12-27 17:09:52-- http://download.wdc.com/nas/WDMyCloudEX2_HDD_Blacklist.xml Resolving download.wdc.com... 35.165.176.197, 44.226.106.124, 44.229.153.191, ... Connecting to download.wdc.com|35.165.176.197|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 256 [text/xml] Saving to: '/tmp/temp_list.xml' 100%[======================================>] 256 --.-K/s in 0s 2021-12-27 17:09:52 (7.18 MB/s) - '/tmp/temp_list.xml' saved [256/256] waiting : [10] ^[[Amcu version 1.04 chk_io v1.04.20141112 system daemon v1.04.20141211 PIP is disabled, exiting. Mon Dec 27 17:09:58 CET 2021 - %I - Communication Manager - Start /usr/local/modules/script/system_init: line 1266: vvctl: not found dev.raid.speed_limit_max = 200000 starting pid 3963, tty '/dev/ttyS0': '/bin/login' BusyBox v1.20.2 (2014-10-30 15:26:14 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. root@WDMyCloudMirror / # root@WDMyCloudMirror / # root@WDMyCloudMirror / # root@WDMyCloudMirror / # killall: chk_hotplug: no process killed call load_module ### create systemfile ### /usr/sbin/load_module: line 541: can't create /sys/block/sdb/queue/read_ahead_kb: nonexistent directory ### sata_reload_application start ### reboot root@WDMyCloudMirror / # killall: quotacheck: no process killed killall: chk_hotplug: no process killed killall: op_server: no process killed Cannot get device settings: No such device Cannot get wake-on-lan settings: No such device Cannot get message level: No such device Cannot get link status: No such device Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 10.10.10.248 port = 49154 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://10.10.10.248:49154/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized Starting atopacctd Advertisements Sent Starting atop system monitor atop atop started *** APKG Daemon is starting ... *** Rename is FAILE USE 2nd Rename killall: smbd: no process killed Starting wdnotifier sh: you need to specify whom to kill kill_running_process all... sh: you need to specify whom to kill LOCK itunes.sh Touch itunes tmp file sh: you need to specify whom to kill wdnotifier started Starting wdmcserver mt-daapd db path no found ..... UNLOCK itunes.sh sh: you need to specify whom to kill killall: rsync: no process killed Shutting down AFP services: killall: netatalk: no process killed Starting wdphotodbmerger WDPhotodbmerger started 0 killall: smbd: no process killed killall: chk_blockip: no process killed killall: chk_blockip: no process killed Stopping atopacct Stopping atop system monitor atop 4390 Stopping wdnotifier wdnotifier failed to stop Stopping wdphotodbmerger killall: sysinfod: no process killed Stopping wdmcserver 3077 root 4096 S avahi-daemon: running [WDMyCloudMirror.local] killall: elephantdriveDaemon: no process killed ### sata_reload_application end ### /usr/sbin/kill_running_process: line 121: vvctl: not found PHY_LAN_NUMBER=1 BOND_ENABLE=0 VLAN0_ENABLE=0 VLAN1_ENABLE=0 **LLTD DISABLE**** kill_running_process done. !!! ### APKG Server Terminated ### !!! killall: snmpd: no process killed restart sysinfod... sysinfod: full update begin... sysinfod: disk connected: previous=0xffffffff, now=0x2 --2021-12-27 17:10:27-- http://download.wdc.com/nas/WDMyCloudEX2_HDD_Blacklist.xml Resolving download.wdc.com... 44.229.153.191, 35.165.176.197, 44.226.106.124, ... Connecting to download.wdc.com|44.229.153.191|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 256 [text/xml] Saving to: '/tmp/temp_list.xml' 100%[======================================>] 256 --.-K/s in 0s 2021-12-27 17:10:27 (7.53 MB/s) - '/tmp/temp_list.xml' saved [256/256] sysinfod: Disk2(sda) detected. UBIFS: un-mount UBI device 0, volume 0 killall: system_daemon: no process killed killall: fan_control: no process killed
Marvell>> printenv CASset=min MALLOC_len=5 autoload=no baudrate=115200 bootargs=root=/dev/ram console=ttyS0,115200 max_loop=32 bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootdelay=1 cacheShare=no console=console=ttyS0,115200 disL2Cache=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaFPU=no enaWrAllo=no eth1addr=00:50:43:02:00:00 eth1mtu=1500 ethact=egiga1 ethaddr=00:50:43:02:02:00 ethmtu=1500 ethprime=egiga0 image_name=uImage initrd_name=uInitrd ipaddr=2.66.66.200 loadaddr=0x02000000 loads_echo=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:4m(boot),-(rootfs) mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500 mv_pon_addr=00:50:43:00:00:02 nandEcc=1bit netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 rcvrip=169.254.100.100 rootpath=/srv/oneiric sata_delay_reset=0 sata_dma_mode=yes serverip=2.66.66.32 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=1 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 1516/524284 bytes
root@mcm:~# cat /proc/mtd dev: size erasesize name root@mcm:~# dmesg | grep mtd root@mcm:~# dmesg | grep -i mtd root@mcm:~# dmesg | grep -i nand root@mcm:/usr/src/linux-stable# grep -i nand /usr/src/linux-stable/.config # NAND # CONFIG_MTD_ONENAND is not set # CONFIG_MTD_RAW_NAND is not set # CONFIG_MTD_SPI_NAND is not set # CONFIG_MTD_NAND_ECC_SW_HAMMING is not set # CONFIG_MTD_NAND_ECC_SW_BCH is not set # end of NAND root@mcm:/usr/src/linux-stable# uname -r 5.16.0-rc7
root@mcm:~# mtdinfo Count of MTD devices: 0 root@mcm:~# cat /proc/mtd dev: size erasesize name root@mcm:~# dmesg | grep mt [ 2.694784] mtdoops: mtd device (mtddev=name/number) must be supplied root@mcm:~# dmesg | grep nand [ 2.700217] marvell-nfc soc:internal-regs:nand@d0000: invalid resource [ 2.705536] marvell-nfc: probe of soc:internal-regs:nand@d0000 failed with error -22 root@mcm:~# grep CONFIG_MTD /usr/src/linux-stable/.config | grep -v '\=y' # CONFIG_MTD_TESTS is not set # CONFIG_MTD_AR7_PARTS is not set CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1 # CONFIG_MTD_CFI_BE_BYTE_SWAP is not set # CONFIG_MTD_CFI_LE_BYTE_SWAP is not set # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_OTP is not set # CONFIG_MTD_RAM is not set # CONFIG_MTD_ROM is not set # CONFIG_MTD_ABSENT is not set # CONFIG_MTD_PHYSMAP is not set # CONFIG_MTD_IMPA7 is not set # CONFIG_MTD_PCI is not set # CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # CONFIG_MTD_PMC551 is not set # CONFIG_MTD_DATAFLASH is not set # CONFIG_MTD_MCHP23K256 is not set # CONFIG_MTD_MCHP48L640 is not set # CONFIG_MTD_SST25L is not set # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set # CONFIG_MTD_DOCG3 is not set # CONFIG_MTD_ONENAND_VERIFY_WRITE is not set # CONFIG_MTD_ONENAND_GENERIC is not set # CONFIG_MTD_ONENAND_OTP is not set # CONFIG_MTD_ONENAND_2X_PROGRAM is not set # CONFIG_MTD_NAND_DENALI_PCI is not set # CONFIG_MTD_NAND_DENALI_DT is not set # CONFIG_MTD_NAND_CAFE is not set # CONFIG_MTD_NAND_BRCMNAND is not set # CONFIG_MTD_NAND_MXIC is not set # CONFIG_MTD_NAND_CADENCE is not set # CONFIG_MTD_NAND_ARASAN is not set # CONFIG_MTD_NAND_INTEL_LGM is not set # CONFIG_MTD_NAND_NANDSIM is not set # CONFIG_MTD_NAND_RICOH is not set # CONFIG_MTD_NAND_DISKONCHIP is not set # CONFIG_MTD_LPDDR is not set # CONFIG_MTD_LPDDR2_NVM is not set # CONFIG_MTD_SPI_NOR_SWP_DISABLE is not set # CONFIG_MTD_SPI_NOR_SWP_KEEP is not set CONFIG_MTD_UBI_WL_THRESHOLD=4096 CONFIG_MTD_UBI_BEB_LIMIT=20 # CONFIG_MTD_UBI_FASTMAP is not set # CONFIG_MTD_UBI_GLUEBI is not set # CONFIG_MTD_UBI_BLOCK is not set root@mcm:~#
Marvell>> nand info Device 0: nand0, sector size 128 KiB Page size 2048 b OOB size 64 b Erase size 131072 b Marvell>> mt mtest mtdparts Marvell>> mtdparts device nand0 <armada-nand>, # parts = 2 #: name size offset mask_flags 0: boot 0x000000400000 0x000000000000 0 1: rootfs 0x00000fc00000 0x000000400000 0 active partition: nand0,0 - (boot) 0x000000400000 @ 0x000000000000 defaults: mtdids : none mtdparts: none Marvell>>
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 29, 2021 03:31AM |
Registered: 2 years ago Posts: 8 |
root@mcm:/lib/modules/5.16.0-rc7# insmod ./kernel/drivers/mtd/mtdoops.ko mtddev=/dev/oops root@mcm:/lib/modules/5.16.0-rc7# echo $? 0 root@mcm:/lib/modules/5.16.0-rc7# ls -lah /dev/oops ls: cannot access '/dev/oops': No such file or directory root@mcm:/lib/modules/5.16.0-rc7# cat /proc/mtd dev: size erasesize name root@mcm:/lib/modules/5.16.0-rc7# ls /dev/m mapper/ md0 mem root@mcm:/lib/modules/5.16.0-rc7# cat /proc/mtd dev: size erasesize name
root@mcm:/sys/devices# dmesg | grep -i nand [ 2.694272] marvell-nfc soc:internal-regs:nand@d0000: invalid resource [ 2.699538] marvell-nfc: probe of soc:internal-regs:nand@d0000 failed with error -22 root@mcm:/sys/devices#
Quote
Miquèl
Perhaps the issues comes from your device tree, as this lines says. You
should check the bindings and verify they are in sync.
nand@d0000 { status = "okay"; compatible = "marvell,armada370-nand"; num-cs = <1>; marvell,nand-enable-arbiter; nand-on-flash-bbt; nand-ecc-strength = <4>; nand-ecc-step-size = <512>; partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; partition@0 { label = "u-Boot"; reg = <0x00000000 0x00500000>; // Warning: New style: <start size> not old <start end> ! read-only; }; partition@500000 { label = "uImage"; reg = <0x00500000 0x00500000>; }; partition@a00000 { label = "ramdisk"; reg = <0x00A00000 0x00500000>; }; partition@f00000 { label = "image.cfs"; reg = <0x00f00000 0x0c900000>; }; partition@dd00000 { label = "rescue firmware"; reg = <0x0dd00000 0x00f00000>; }; partition@ec00000 { label = "config"; reg = <0x0ec00000 0x01400000>; }; partition@d800000 { label = "reserve"; reg = <0x0d800000 0x00500000>; }; };
mtdparts=mtdparts=armada-nand:4m(boot),-(rootfs)
CONFIG_MTD_NAND_ECC=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_PXA3xx=y
Marvell>> dhcp BOOTP broadcast 1 BOOTP broadcast 2 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 119 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 119 DHCP client bound to address 10.10.10.145 Marvell>> setenv serverip 10.10.10.10 Marvell>> tftp ${loadaddr} uImage-nand-enabled Using egiga1 device TFTP from server 10.10.10.10; our IP address is 10.10.10.145 Filename 'uImage-nand-enabled'. Load address: 0x2000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ########################################### done Bytes transferred = 4446765 (43da2d hex) Marvell>> setenv bootargs 'root=/dev/md0 console=ttyS0,115200 max_loop=32 raid=autodetect' Marvell>> set bootcmd "dhcp; tftp ${loadaddr} ${serverip}:uImage-nand-enabled; bootm" Marvell>> bootm ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: armada-370-wdmc-mirror-gen1 Created: 2021-12-29 8:40:20 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4446701 Bytes = 4.2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... DTB:0x00441FA0 (0x00003A4D) C:0x000080E0-0x00445A60->0x00E7FE00-0x012BD780 DTB:0x012B9CC0 (0x00003AA2) Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.16.0-rc7 (root@htpc) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #2 SMP Wed Dec 29 09:22:11 CET 2021 CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache OF: fdt: Machine model: WD MyCloud Mirror Memory policy: Data cache writeback Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] CPU: All CPU(s) started in SVC mode. percpu: Embedded 11 pages/cpu s14412 r8192 d22452 u45056 Built 1 zonelists, mobility grouping on. Total pages: 129920 Kernel command line: root=/dev/md0 console=ttyS0,115200 max_loop=32 raid=autodetect Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 504956K/524288K available (9216K kernel code, 508K rwdata, 2176K rodata, 1024K init, 337K bss, 19332K reserved, 0K cma-reserved, 0K highmem) rcu: Hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 L2C: DT/platform modifies aux control register: 0x12086302 -> 0x1a086302 Aurora cache controller enabled, 4 ways, 256 kB Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 random: get_random_bytes called from start_kernel+0x480/0x630 with crng_init=0 Switching to timer-based delay loop, resolution 53ns sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114532461029ns clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101933890472 ns Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 37.50 BogoMIPS (lpj=187500) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket -1, mpidr 0 Setting up static identity map for 0x100000 - 0x100060 mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 mvebu-pmsu: Initializing Power Management Service Unit rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... smp: Brought up 1 node, 1 CPU SMP: Total of 1 processors activated (37.50 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: 2, 16384 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered PF_NETLINK/PF_ROUTE protocol family DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' cpuidle: using governor ladder cryptd: max_cpu_qlen set to 1000 raid6: int32x8 gen() 376 MB/s raid6: int32x8 xor() 228 MB/s raid6: int32x4 gen() 382 MB/s raid6: int32x4 xor() 220 MB/s raid6: int32x2 gen() 531 MB/s raid6: int32x2 xor() 251 MB/s raid6: int32x1 gen() 471 MB/s raid6: int32x1 xor() 207 MB/s raid6: using algorithm int32x2 gen() 531 MB/s raid6: .... xor() 251 MB/s, rmw enabled raid6: using intx1 recovery algorithm SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Bluetooth: Core ver 2.22 NET: Registered PF_BLUETOOTH protocol family Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized clocksource: Switched to clocksource armada_370_xp_clocksource VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) FS-Cache: Loaded CacheFiles: Loaded NET: Registered PF_INET protocol family IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Initialise system trusted keyrings workingset: timestamp_bits=14 max_order=17 bucket_order=3 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). FS-Cache: Netfs 'cifs' registered for caching Key type cifs.idmap registered xor: measuring software checksum speed arm4regs : 1151 MB/sec 8regs : 880 MB/sec 32regs : 1151 MB/sec xor: using function: 32regs (1151 MB/sec) async_tx: api initialized (async) Key type asymmetric registered Asymmetric key parser 'x509' registered Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler kyber registered armada-370-pinctrl f1018000.pin-ctrl: registered pinctrl driver mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: mvebu-pcie soc:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 mvebu-pcie soc:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000 mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff]) pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400 pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400 pci 0000:00:02.0: reg 0x38: [mem 0x00000000-0x000007ff pref] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:01:00.0: [1912:0015] type 00 class 0x0c0330 pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x40001fff 64bit] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold PCI: bus1: Fast back to back transfers disabled pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 PCI: bus2: Fast back to back transfers enabled pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8100000-0xf81007ff pref] pci 0000:00:02.0: BAR 6: assigned [mem 0xf8200000-0xf82007ff pref] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8001fff 64bit] pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] pci 0000:00:02.0: PCI bridge to [bus 02] mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled printk: console [ttyS0] disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 12500000) is a 16550A printk: console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 29, base_baud = 12500000) is a 16550A brd: module loaded loop: module loaded sata_mv f10a0000.sata: slots 32 ports 2 scsi host0: sata_mv scsi host1: sata_mv ata1: SATA max UDMA/133 irq 37 ata2: SATA max UDMA/133 irq 37 mtdoops: mtd device (mtddev=name/number) must be supplied marvell-nfc soc:internal-regs:nand@d0000: invalid resource marvell-nfc: probe of soc:internal-regs:nand@d0000 failed with error -22 libphy: Fixed MDIO Bus: probed libphy: orion_mdio_bus: probed mvneta f1074000.ethernet eth0: Using hardware mac address 00:50:43:02:02:00 usbcore: registered new interface driver lan78xx ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-orion: EHCI orion driver orion-ehci f1050000.usb: EHCI Host Controller orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1050000.usb: irq 35, io mem 0xf1050000 orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 5.16.0-rc7 ehci_hcd usb usb1: SerialNumber: f1050000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata1.00: ATA-9: WDC WD30EZRX-00DC0B0, 80.00A80, max UDMA/133 ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD30EZRX-00D 0A80 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 0:0:0:0: [sda] Attached SCSI disk rtc-mv f1010300.rtc: internal RTC not ticking i2c_dev: i2c /dev entries driver mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ata2.00: ATA-9: WDC WD30EZRX-00DC0B0, 80.00A80, max UDMA/133 ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) ledtrig-cpu: registered to indicate activity on CPUs marvell-cesa f1090000.crypto: CESA device successfully registered hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered PF_INET6 protocol family Segment Routing with IPv6 In-situ OAM (IOAM) with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered PF_PACKET protocol family Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered Registering SWP/SWPB emulation handler ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD30EZRX-00D 0A80 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) sd 1:0:0:0: [sdb] 4096-byte physical blocks Loading compiled-in X.509 certificates sd 1:0:0:0: [sdb] Write Protect is off Key type ._fscrypt registered Key type .fscrypt registered Key type fscrypt-provisioning registered sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA armada-370-pinctrl f1018000.pin-ctrl: unsupported function gpio on pin mpp54 pinctrl core: failed to register map default (0): invalid type given sdb: sdb1 sd 1:0:0:0: [sdb] Attached SCSI disk input: gpio-keys as /devices/platform/gpio-keys/input/input0 ### dt-test ### start of unittest - you will see error messages ### dt-test ### EXPECT \ : Duplicate name in testcase-data, renamed to "duplicate-name#1" Duplicate name in testcase-data, renamed to "duplicate-name#1" ### dt-test ### EXPECT / : Duplicate name in testcase-data, renamed to "duplicate-name#1" ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-a: could not get #phandle-cells-missing for /testcase-data/phandle-tests/provider1 OF: /testcase-data/phandle-tests/consumer-a: could not get #phandle-cells-missing for /testcase-data/phandle-tests/provider1 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-a: could not get #phandle-cells-missing for /testcase-data/phandle-tests/provider1 ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-a: could not get #phandle-cells-missing for /testcase-data/phandle-tests/provider1 OF: /testcase-data/phandle-tests/consumer-a: could not get #phandle-cells-missing for /testcase-data/phandle-tests/provider1 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-a: could not get #phandle-cells-missing for /testcase-data/phandle-tests/provider1 ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-a: could not find phandle OF: /testcase-data/phandle-tests/consumer-a: could not find phandle 12345678 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-a: could not find phandle ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-a: could not find phandle OF: /testcase-data/phandle-tests/consumer-a: could not find phandle 12345678 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-a: could not find phandle ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-a: #phandle-cells = 3 found -1 OF: /testcase-data/phandle-tests/consumer-a: #phandle-cells = 3 found -1 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-a: #phandle-cells = 3 found -1 ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-a: #phandle-cells = 3 found -1 OF: /testcase-data/phandle-tests/consumer-a: #phandle-cells = 3 found -1 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-a: #phandle-cells = 3 found -1 ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-b: could not get #phandle-missing-cells for /testcase-data/phandle-tests/provider1 OF: /testcase-data/phandle-tests/consumer-b: could not get #phandle-missing-cells for /testcase-data/phandle-tests/provider1 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-b: could not get #phandle-missing-cells for /testcase-data/phandle-tests/provider1 ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-b: could not find phandle OF: /testcase-data/phandle-tests/consumer-b: could not find phandle 12345678 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-b: could not find phandle ### dt-test ### EXPECT \ : OF: /testcase-data/phandle-tests/consumer-b: #phandle-cells = 2 found -1 OF: /testcase-data/phandle-tests/consumer-b: #phandle-cells = 2 found -1 ### dt-test ### EXPECT / : OF: /testcase-data/phandle-tests/consumer-b: #phandle-cells = 2 found -1 ### dt-test ### FAIL of_unittest_dma_ranges_one():923 of_dma_get_range: wrong DMA addr 0x00000000 (expecting 100000000) on node /testcase-data/address-tests/bus@80000000/device@1000 ### dt-test ### EXPECT \ : platform testcase-data:testcase-device2: IRQ index 0 not found platform testcase-data:testcase-device2: IRQ index 0 not found ### dt-test ### EXPECT / : platform testcase-data:testcase-device2: IRQ index 0 not found ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest0/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest0/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest0/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest1/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest1/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest1/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest2/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest2/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest2/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest3/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest3/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest3/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest5/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest5/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest5/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest6/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest6/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest6/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest7/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest7/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest7/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest8/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest8/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest8/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest8/property-foo OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest8/property-foo ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/test-unittest8/property-foo ### dt-test ### EXPECT \ : OF: overlay: node_overlaps_later_cs: #6 overlaps with #7 @/testcase-data/overlay-node/test-bus/test-unittest8 ### dt-test ### EXPECT \ : OF: overlay: overlay #6 is not topmost OF: overlay: node_overlaps_later_cs: #6 overlaps with #7 @/testcase-data/overlay-node/test-bus/test-unittest8 OF: overlay: overlay #6 is not topmost ### dt-test ### EXPECT / : OF: overlay: overlay #6 is not topmost ### dt-test ### EXPECT / : OF: overlay: node_overlaps_later_cs: #6 overlaps with #7 @/testcase-data/overlay-node/test-bus/test-unittest8 ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/i2c-test-bus/test-unittest12/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/i2c-test-bus/test-unittest12/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/i2c-test-bus/test-unittest12/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/i2c-test-bus/test-unittest13/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/i2c-test-bus/test-unittest13/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data/overlay-node/test-bus/i2c-test-bus/test-unittest13/status ### dt-test ### EXPECT \ : i2c i2c-1: Added multiplexed i2c bus 3 ### dt-test ### EXPECT / : i2c i2c-1: Added multiplexed i2c bus 3 ### dt-test ### EXPECT \ : gpio-<<int>> (line-B-input): hogged as input ### dt-test ### EXPECT \ : gpio-<<int>> (line-A-input): hogged as input gpio-509 (line-B-input): hogged as input gpio-503 (line-A-input): hogged as input ### dt-test ### EXPECT / : gpio-<<int>> (line-A-input): hogged as input ### dt-test ### EXPECT / : gpio-<<int>> (line-B-input): hogged as input ### dt-test ### EXPECT \ : gpio-<<int>> (line-D-input): hogged as input gpio-501 (line-D-input): hogged as input ### dt-test ### EXPECT / : gpio-<<int>> (line-D-input): hogged as input ### dt-test ### EXPECT \ : gpio-<<int>> (line-C-input): hogged as input gpio-495 (line-C-input): hogged as input ### dt-test ### EXPECT / : gpio-<<int>> (line-C-input): hogged as input ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/substation@100/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/ride@100/track@30/incline-up ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/ride@100/track@40/incline-up ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/status ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/color ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/rate ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/hvac_2 ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200 ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200_left ### dt-test ### EXPECT \ : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200_right OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/substation@100/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/ride@100/track@30/incline-up OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/ride@100/track@40/incline-up OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/status OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/color OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/rate OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/hvac_2 OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200 OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200_left OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200_right ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200_right ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200_left ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/ride_200 ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/hvac_2 ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/rate ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/color ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/lights@40000/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/ride@100/track@40/incline-up ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/ride@100/track@30/incline-up ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/fairway-1/status ### dt-test ### EXPECT / : OF: overlay: WARNING: memory leak will occur if overlay removed, property: /testcase-data-2/substation@100/status ### dt-test ### EXPECT \ : OF: overlay: ERROR: multiple fragments add and/or delete node /testcase-data-2/substation@100/motor-1/controller ### dt-test ### EXPECT \ : OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/controller/name OF: overlay: ERROR: multiple fragments add and/or delete node /testcase-data-2/substation@100/motor-1/controller OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/controller/name ### dt-test ### EXPECT / : OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/controller/name ### dt-test ### EXPECT / : OF: overlay: ERROR: multiple fragments add and/or delete node /testcase-data-2/substation@100/motor-1/controller ### dt-test ### EXPECT \ : OF: overlay: ERROR: multiple fragments add and/or delete node /testcase-data-2/substation@100/motor-1/electric ### dt-test ### EXPECT \ : OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/electric/rpm_avail ### dt-test ### EXPECT \ : OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/electric/name OF: overlay: ERROR: multiple fragments add and/or delete node /testcase-data-2/substation@100/motor-1/electric OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/electric/rpm_avail OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/electric/name ### dt-test ### EXPECT / : OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/electric/name ### dt-test ### EXPECT / : OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/electric/rpm_avail ### dt-test ### EXPECT / : OF: overlay: ERROR: multiple fragments add and/or delete node /testcase-data-2/substation@100/motor-1/electric ### dt-test ### end of unittest - 255 passed, 1 failed md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: autorun ... md: running: <sdb1><sda1> md0: detected capacity change from 0 to 11721058304 md: ... autorun DONE. random: fast init done EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. VFS: Mounted root (ext4 filesystem) readonly on device 9:0. devtmpfs: mounted Freeing unused kernel image (initmem) memory: 1024K Run /sbin/init as init process INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Files under mount point '/run' will be hidden. ... (warning). Starting hotplug events dispatcher: systemd-udevdrandom: crng init done . Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 done. Setting hostname to 'mcm'...done. Activating swap:. EXT4-fs (md0): re-mounted. Opts: (null). Quota mode: none. Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/md0 e2fsck 1.46.2 (28-Feb-2021) /dev/md0: clean, 156631/183144448 files, 220589812/1465132288 blocks . EXT4-fs (md0): re-mounted. Opts: errors=remount-ro. Quota mode: none. Will now check all file systems. Checking all file systems. UUID=11b0ad4f-fe83-4644-a42b-59f24ec8c048 is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. Initializing random number generator...done. mvneta f1074000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL) mvneta f1074000.ethernet eth0: configuring for phy/rgmii-id link mode Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:02:02:00 Sending on LPF/eth0/00:50:43:02:02:00 Sending on Socket/fallback DHCPREQUEST for 10.10.10.145 on eth0 to 255.255.255.255 port 67 mvneta f1074000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST for 10.10.10.145 on eth0 to 255.255.255.255 port 67 DHCPREQUEST for 10.10.10.145 on eth0 to 255.255.255.255 port 67 DHCPACK of 10.10.10.145 from 10.10.10.10 bound to 10.10.10.145 -- renewal in 40270 seconds. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Not starting NFS kernel daemon: no exports. ... (warning). Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1931 (syslogd) . Starting periodic command scheduler: cron. Starting system message bus: dbus. Starting MCU control daemon for fan and LEDs: mcm-daemon. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting NTP server: ntpd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1957 (klogd) . Starting rsync daemon: rsync. Starting OpenBSD Secure Shell server: sshd. Starting S.M.A.R.T. daemon: smartd. Running local boot scripts (/etc/rc.local) Configuration file wrong or corrupted <13>Jan 1 01:00:56 root[2096]: Cannot read u-boot env ethaddr . Debian GNU/Linux 11 mcm ttyS0 mcm login:
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 29, 2021 12:04PM |
Registered: 2 years ago Posts: 8 |
root@mcm:~# cat /proc/mtd dev: size erasesize name mtd0: 10000000 00020000 "pxa3xx_nand-0" mtd1: 00500000 00020000 "u-Boot" mtd2: 00500000 00020000 "uImage" mtd3: 00500000 00020000 "ramdisk" mtd4: 0c900000 00020000 "image.cfs" mtd5: 00f00000 00020000 "rescue firmware" mtd6: 01400000 00020000 "config" mtd7: 00500000 00020000 "reserve" root@mcm:~# uname -r 4.14.260 root@mcm:~#
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 29, 2021 03:27PM |
Admin Registered: 13 years ago Posts: 18,821 |
> dev: size erasesize name > mtd0: 10000000 00020000 "pxa3xx_nand-0" > mtd1: 00500000 00020000 "u-Boot" > mtd2: 00500000 00020000 "uImage" > mtd3: 00500000 00020000 "ramdisk" > mtd4: 0c900000 00020000 "image.cfs" > mtd5: 00f00000 00020000 "rescue firmware" > mtd6: 01400000 00020000 "config" > mtd7: 00500000 00020000 "reserve"
> root@mcm:~# uname -r > 4.14.260 > root@mcm:~#
nanddump --noecc --omitoob mtd0.wd_my_cloud /dev/mtd0
usb start ext2ls usb 0:1 /If it works, then loading from USB is better.
Quote
> root@mcm:~# uname -r
4.14.260
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 29, 2021 09:46PM |
Admin Registered: 13 years ago Posts: 18,821 |
dd if=uImage-nand-enabled of=uImage-nand-enabled.kwb bs=5120k conv=sync
ls -lh uImage-nand-enabled.kwb
flash_erase /dev/mtd2 0 0 nandwrite /dev/mtd2 uImage-nand-enabled.kwb
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 30, 2021 03:48PM |
Registered: 2 years ago Posts: 8 |
root@mcm:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.260 (root@htpc) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Dec 29 16:38:05 CET 2021 [ 0.000000] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: WD MyCloud Mirror [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] free_area_init_node: node 0, pgdat c0c46cc0, node_mem_map dfb78000 [ 0.000000] Normal zone: 1152 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 131072 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 15 pages/cpu s28684 r8192 d24564 u61440 [ 0.000000] pcpu-alloc: s28684 r8192 d24564 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: root=/dev/md0 console=ttyS0,115200 max_loop=32 raid=autodetect [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 507332K/524288K available (7352K kernel code, 288K rwdata, 1768K rodata, 1024K init, 207K bss, 16956K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc082e3b0 (8345 kB) .init : 0xc0b00000 - 0xc0c00000 (1024 kB) .data : 0xc0c00000 - 0xc0c483e0 ( 289 kB) .bss : 0xc0c4a000 - 0xc0c7dc90 ( 208 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x12086302 -> 0x1a086302 [ 0.000000] Aurora cache controller enabled, 4 ways, 256 kB [ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 [ 0.000000] Switching to timer-based delay loop, resolution 53ns [ 0.000006] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114532461029ns [ 0.000019] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101933890472 ns [ 0.000351] Console: colour dummy device 80x30 [ 0.000373] Calibrating delay loop (skipped), value calculated using timer frequency.. 37.50 BogoMIPS (lpj=187500) [ 0.000384] pid_max: default: 32768 minimum: 301 [ 0.000504] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000512] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000965] CPU: Testing write buffer coherency: ok [ 0.001185] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.001472] Setting up static identity map for 0x100000 - 0x100060 [ 0.001726] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 [ 0.001803] mvebu-pmsu: Initializing Power Management Service Unit [ 0.001909] Hierarchical SRCU implementation. [ 0.002251] smp: Bringing up secondary CPUs ... [ 0.002258] smp: Brought up 1 node, 1 CPU [ 0.002264] SMP: Total of 1 processors activated (37.50 BogoMIPS). [ 0.002269] CPU: All CPU(s) started in SVC mode. [ 0.002800] devtmpfs: initialized [ 0.005107] random: get_random_u32 called from bucket_table_alloc+0x100/0x22c with crng_init=0 [ 0.005321] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.005481] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.005494] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.005551] xor: measuring software checksum speed [ 0.100056] arm4regs : 1104.000 MB/sec [ 0.200058] 8regs : 846.400 MB/sec [ 0.300056] 32regs : 1103.200 MB/sec [ 0.300061] xor: using function: arm4regs (1104.000 MB/sec) [ 0.300069] pinctrl core: initialized pinctrl subsystem [ 0.300297] regulator-dummy: no parameters [ 0.301366] NET: Registered protocol family 16 [ 0.301677] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.302277] cpuidle: using governor ladder [ 0.500217] raid6: int32x1 gen() 162 MB/s [ 0.670076] raid6: int32x1 xor() 214 MB/s [ 0.840197] raid6: int32x2 gen() 255 MB/s [ 1.010162] raid6: int32x2 xor() 248 MB/s [ 1.180212] raid6: int32x4 gen() 264 MB/s [ 1.350112] raid6: int32x4 xor() 204 MB/s [ 1.520243] raid6: int32x8 gen() 303 MB/s [ 1.690076] raid6: int32x8 xor() 203 MB/s [ 1.690081] raid6: using algorithm int32x8 gen() 303 MB/s [ 1.690085] raid6: .... xor() 203 MB/s, rmw enabled [ 1.690089] raid6: using intx1 recovery algorithm [ 1.690221] reg-fixed-voltage regulators:regulator@1: could not find pctldev for node /soc/internal-regs/pin-ctrl@18000/xhci-pwr-pin, deferring probe [ 1.690249] reg-fixed-voltage regulators:regulator@2: could not find pctldev for node /soc/internal-regs/pin-ctrl@18000/sata-1-pwr-pin, deferring probe [ 1.690269] reg-fixed-voltage regulators:regulator@3: could not find pctldev for node /soc/internal-regs/pin-ctrl@18000/sata-2-pwr-pin, deferring probe [ 1.690642] SCSI subsystem initialized [ 1.693019] libata version 3.00 loaded. [ 1.693208] usbcore: registered new interface driver usbfs [ 1.693246] usbcore: registered new interface driver hub [ 1.693283] usbcore: registered new device driver usb [ 1.693362] pps_core: LinuxPPS API ver. 1 registered [ 1.693366] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.693381] PTP clock support registered [ 1.695317] Bluetooth: Core ver 2.22 [ 1.695359] NET: Registered protocol family 31 [ 1.695363] Bluetooth: HCI device and connection manager initialized [ 1.695372] Bluetooth: HCI socket layer initialized [ 1.695378] Bluetooth: L2CAP socket layer initialized [ 1.695397] Bluetooth: SCO socket layer initialized [ 1.695729] clocksource: Switched to clocksource armada_370_xp_clocksource [ 1.695839] VFS: Disk quotas dquot_6.6.0 [ 1.695888] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.695956] FS-Cache: Loaded [ 1.696254] CacheFiles: Loaded [ 1.710868] NET: Registered protocol family 2 [ 1.710992] IP idents hash table entries: 8192 (order: 4, 65536 bytes) [ 1.711389] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 1.711420] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 1.711456] TCP: Hash tables configured (established 4096 bind 4096) [ 1.711514] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.711528] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.711613] NET: Registered protocol family 1 [ 1.712484] RPC: Registered named UNIX socket transport module. [ 1.712492] RPC: Registered udp transport module. [ 1.712495] RPC: Registered tcp transport module. [ 1.712499] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.712507] PCI: CLS 0 bytes, default 64 [ 1.713790] Initialise system trusted keyrings [ 1.714343] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 1.715061] NFS: Registering the id_resolver key type [ 1.715081] Key type id_resolver registered [ 1.715085] Key type id_legacy registered [ 1.715094] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.715408] FS-Cache: Netfs 'cifs' registered for caching [ 1.719805] async_tx: api initialized (async) [ 1.719817] Key type asymmetric registered [ 1.719821] Asymmetric key parser 'x509' registered [ 1.719882] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.719888] io scheduler noop registered [ 1.719892] io scheduler deadline registered [ 1.719916] io scheduler cfq registered (default) [ 1.719920] io scheduler kyber registered [ 1.720588] armada-370-pinctrl f1018000.pin-ctrl: registered pinctrl driver [ 1.721490] gpio gpiochip0: (f1018100.gpio): added GPIO chardev (254:0) [ 1.721560] gpiochip_setup_dev: registered GPIOs 0 to 31 on device: gpiochip0 (f1018100.gpio) [ 1.722005] gpio gpiochip1: (f1018140.gpio): added GPIO chardev (254:1) [ 1.722073] gpiochip_setup_dev: registered GPIOs 32 to 63 on device: gpiochip1 (f1018140.gpio) [ 1.722477] gpio gpiochip2: (f1018180.gpio): added GPIO chardev (254:2) [ 1.722538] gpiochip_setup_dev: registered GPIOs 64 to 65 on device: gpiochip2 (f1018180.gpio) [ 1.722808] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/soc/pcie@82000000/pcie@1,0[0]' [ 1.722835] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/soc/pcie@82000000/pcie@2,0[0]' [ 1.723020] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 [ 1.723033] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.723039] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 1.723047] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.723076] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400 [ 1.723247] pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400 [ 1.723395] PCI: bus0: Fast back to back transfers disabled [ 1.723404] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.723414] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.723517] pci 0000:01:00.0: [1912:0015] type 00 class 0x0c0330 [ 1.723558] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x40001fff 64bit] [ 1.723688] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.723822] PCI: bus1: Fast back to back transfers disabled [ 1.723832] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.723903] PCI: bus2: Fast back to back transfers enabled [ 1.723911] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.723943] pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff] [ 1.723953] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8001fff 64bit] [ 1.723968] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.723977] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 1.723985] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.724324] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.786320] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.787544] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.846312] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.942549] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.944844] console [ttyS0] disabled [ 1.965002] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 20, base_baud = 12500000) is a 16550A [ 2.634050] console [ttyS0] enabled [ 2.657179] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 21, base_baud = 12500000) is a 16550A [ 2.670651] brd: module loaded [ 2.691802] loop: module loaded [ 2.694004] sata_mv f10a0000.sata: version 1.28 [ 2.694197] sata_mv f10a0000.sata: slots 32 ports 2 [ 2.700080] scsi host0: sata_mv [ 2.702423] scsi host1: sata_mv [ 2.704414] ata1: SATA max UDMA/133 irq 29 [ 2.707288] ata2: SATA max UDMA/133 irq 29 [ 2.711294] pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device [ 2.718278] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 2.723353] nand: Hynix H27U2G8F2CTR-BC [ 2.725945] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.732245] pxa3xx-nand f10d0000.nand: ECC strength 16, ECC step size 2048 [ 2.738283] Bad block table found at page 131008, version 0x01 [ 2.743341] Bad block table found at page 130944, version 0x01 [ 2.748180] nand_read_bbt: bad block at 0x000005a60000 [ 2.752086] 7 ofpart partitions found on MTD device pxa3xx_nand-0 [ 2.759323] ftl_cs: FTL header not found. [ 2.762544] Creating 7 MTD partitions on "pxa3xx_nand-0": [ 2.766708] 0x000000000000-0x000000500000 : "u-Boot" [ 2.772930] ftl_cs: FTL header not found. [ 2.776194] 0x000000500000-0x000000a00000 : "uImage" [ 2.782359] ftl_cs: FTL header not found. [ 2.785606] 0x000000a00000-0x000000f00000 : "ramdisk" [ 2.791946] ftl_cs: FTL header not found. [ 2.795136] 0x000000f00000-0x00000d800000 : "image.cfs" [ 2.802373] ftl_cs: FTL header not found. [ 2.805634] 0x00000dd00000-0x00000ec00000 : "rescue firmware" [ 2.812688] ftl_cs: FTL header not found. [ 2.815991] 0x00000ec00000-0x000010000000 : "config" [ 2.821730] random: fast init done [ 2.824173] ftl_cs: FTL header not found. [ 2.827481] 0x00000d800000-0x00000dd00000 : "reserve" [ 2.833741] ftl_cs: FTL header not found. [ 2.837300] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 2.844038] mdio_bus fixed-0: GPIO lookup for consumer reset [ 2.844046] mdio_bus fixed-0: using lookup tables for GPIO lookup [ 2.844052] mdio_bus fixed-0: lookup for GPIO reset failed [ 2.844068] libphy: Fixed MDIO Bus: probed [ 2.847441] mdio_bus f1072004.mdio-mii: GPIO lookup for consumer reset [ 2.847446] mdio_bus f1072004.mdio-mii: using device tree for GPIO lookup [ 2.847455] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/soc/internal-regs/mdio@72004[0]' [ 2.847462] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/soc/internal-regs/mdio@72004[0]' [ 2.847466] mdio_bus f1072004.mdio-mii: using lookup tables for GPIO lookup [ 2.847471] mdio_bus f1072004.mdio-mii: lookup for GPIO reset failed [ 2.847475] libphy: orion_mdio_bus: probed [ 2.855010] mvneta f1074000.ethernet eth0: Using random mac address 72:e5:ea:f3:fd:05 [ 2.861876] usbcore: registered new interface driver lan78xx [ 2.866271] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.871517] ehci-orion: EHCI orion driver [ 2.874348] orion-ehci f1050000.usb: EHCI Host Controller [ 2.878497] orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1 [ 2.884893] orion-ehci f1050000.usb: irq 27, io mem 0xf1050000 [ 2.915543] orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00 [ 2.920348] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.925894] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.931839] usb usb1: Product: EHCI Host Controller [ 2.935429] usb usb1: Manufacturer: Linux 4.14.260 ehci_hcd [ 2.939728] usb usb1: SerialNumber: f1050000.usb [ 2.943620] hub 1-0:1.0: USB hub found [ 2.946297] hub 1-0:1.0: 1 port detected [ 2.949597] usbcore: registered new interface driver usb-storage [ 3.215533] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 3.222946] ata1.00: ATA-9: WDC WD30EZRX-00DC0B0, 80.00A80, max UDMA/133 [ 3.228391] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 3.236403] ata1.00: configured for UDMA/133 [ 3.239723] scsi 0:0:0:0: Direct-Access ATA WDC WD30EZRX-00D 0A80 PQ: 0 ANSI: 5 [ 3.247571] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 3.254046] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 3.258580] sd 0:0:0:0: [sda] Write Protect is off [ 3.262107] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 3.262231] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.965543] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 3.995559] ata2.00: ATA-9: WDC WD30EZRX-00DC0B0, 80.00A80, max UDMA/133 [ 4.000987] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 4.006729] rtc-mv f1010300.rtc: internal RTC not ticking [ 4.010989] i2c /dev entries driver [ 4.024550] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 4.036539] sda: sda1 [ 4.038530] ata2.00: configured for UDMA/133 [ 4.041834] scsi 1:0:0:0: Direct-Access ATA WDC WD30EZRX-00D 0A80 PQ: 0 ANSI: 5 [ 4.049000] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.053707] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 4.060246] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 4.064622] sd 1:0:0:0: [sdb] Write Protect is off [ 4.068182] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 4.068380] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.077606] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com [ 4.085190] sdhci: Secure Digital Host Controller Interface driver [ 4.090149] sdhci: Copyright(c) Pierre Ossman [ 4.093348] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.097926] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/hdd1-blue[0]' - status (0) [ 4.097939] no flags found for gpios [ 4.098036] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/hdd2-blue[0]' - status (0) [ 4.098044] no flags found for gpios [ 4.098112] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/hdd1-red[0]' - status (0) [ 4.098119] no flags found for gpios [ 4.098183] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/hdd2-red[0]' - status (0) [ 4.098190] no flags found for gpios [ 4.099606] ledtrig-cpu: registered to indicate activity on CPUs [ 4.105772] marvell-cesa f1090000.crypto: CESA device successfully registered [ 4.111843] hidraw: raw HID events driver (C) Jiri Kosina [ 4.116107] usbcore: registered new interface driver usbhid [ 4.120395] usbhid: USB HID core driver [ 4.123081] Netfilter messages via NETLINK v0.30. [ 4.126539] nfnl_acct: registering with nfnetlink. [ 4.130127] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 4.135102] arp_tables: arp_tables: (C) 2002 David S. Miller [ 4.139617] NET: Registered protocol family 10 [ 4.144574] Segment Routing with IPv6 [ 4.147062] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.152170] NET: Registered protocol family 17 [ 4.155369] Bridge firewalling registered [ 4.158143] 8021q: 802.1Q VLAN Support v1.8 [ 4.161064] Key type dns_resolver registered [ 4.164108] Registering SWP/SWPB emulation handler [ 4.168887] Loading compiled-in X.509 certificates [ 4.173309] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulators/regulator@1[0]' - status (0) [ 4.173356] USB3.0 Port Power: 5000 mV [ 4.173501] reg-fixed-voltage regulators:regulator@1: USB3.0 Port Power supplying 5000000uV [ 4.173558] armada-370-pinctrl f1018000.pin-ctrl: unsupported function gpio on pin mpp54 [ 4.180480] pinctrl core: failed to register map default (0): invalid type given [ 4.186622] reg-fixed-voltage: probe of regulators:regulator@2 failed with error -22 [ 4.193246] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulators/regulator@3[0]' - status (0) [ 4.194348] sdb: sdb1 [ 4.196620] sd 1:0:0:0: [sdb] Attached SCSI disk [ 8.246005] SATA-2 Power: 5000 mV [ 8.246202] reg-fixed-voltage regulators:regulator@3: SATA-2 Power supplying 5000000uV [ 8.246918] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/reset-button[0]' - status (0) [ 8.246950] gpio-65 (Reset Button): gpiod_set_debounce: missing set() or set_config() operations [ 8.247266] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 8.253632] hctosys: unable to open rtc device (rtc0) [ 8.266952] md: Waiting for all devices to be available before autodetect [ 8.272467] md: If you don't use raid, use raid=noautodetect [ 8.277841] md: Autodetecting RAID arrays. [ 8.337918] md: autorun ... [ 8.339560] md: running: <sdb1><sda1> [ 8.342337] md0: detected capacity change from 0 to 6001181851648 [ 8.347281] md: ... autorun DONE. [ 8.961704] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null) [ 8.968084] VFS: Mounted root (ext4 filesystem) readonly on device 9:0. [ 9.000025] devtmpfs: mounted [ 9.002970] Freeing unused kernel memory: 1024K [ 11.183175] random: crng init done [ 13.977657] evbug: Connected device: input0 (gpio-keys at gpio-keys/input0) [ 14.285746] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 14.315734] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 19.344894] EXT4-fs (md0): re-mounted. Opts: (null) [ 34.321177] EXT4-fs (md0): re-mounted. Opts: errors=remount-ro [ 37.917031] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 42.166686] mvneta f1074000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 42.173460] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 December 30, 2021 03:57PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 January 05, 2022 07:44AM |
Registered: 2 years ago Posts: 8 |
CONFIG_MTD_NAND_ECC=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_PXA3xx=yand that worked.
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 January 05, 2022 03:18PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 January 07, 2022 11:17PM |
Registered: 2 years ago Posts: 8 |
armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC flash read_id : daad NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: bad block at 0x000005a60000 Creating 7 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "u-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "ramdisk" 0x000000f00000-0x00000d800000 : "image.cfs" 0x00000dd00000-0x00000ec00000 : "rescue firmware" 0x00000ec00000-0x000010000000 : "config" 0x00000d800000-0x00000dd00000 : "reserve"
Re: Changing NAND boot process on Western Digital My Cloud Mirror Gen1 January 07, 2022 11:52PM |
Admin Registered: 13 years ago Posts: 18,821 |
> Creating 7 MTD partitions on "armada-nand": > 0x000000000000-0x000000500000 : "u-Boot" > 0x000000500000-0x000000a00000 : "uImage" > 0x000000a00000-0x000000f00000 : "ramdisk" > 0x000000f00000-0x00000d800000 : "image.cfs" > 0x00000dd00000-0x00000ec00000 : "rescue firmware" > 0x00000ec00000-0x000010000000 : "config" > 0x00000d800000-0x00000dd00000 : "reserve" >