Mainline Debian on Iomega ix4-300d March 06, 2022 08:02AM |
Registered: 6 years ago Posts: 183 |
cat vmlinuz armada-xp-lenovo-ix4-300d.dtb > vmlinuz_ix4_300d
mkimage -A arm -O linux -T multi -C none -a 0x04000000 -e 0x04000000 -n "Debian armhf installer" -d vmlinuz_ix4_300d:initrd.gz uImage_di_ix4_300d
scp uImage_di_ix4_300d root@192.168.1.254:/mnt/mmcblk0p1/tftp
setenv serverip 192.168.1.254
ping 192.168.1.254
tftpboot uImage_di_ix4_300d
bootm 0x2000000
mount --bind /dev /target/dev mount -t proc none /target/proc mount -t sysfs none /target/sys chroot /target /bin/sh apt-get update apt-get install flash-kernel
nano /etc/flash-kernel/db
Machine: Lenovo Iomega ix4-300d Kernel-Flavors: armmp armmp-lpae DTB-Id: armada-xp-lenovo-ix4-300d.dtb DTB-Append: yes U-Boot-Kernel-Address: 0x00008000 U-Boot-Initrd-Address: 0x0 Boot-Kernel-Path: /boot/uImage Boot-Initrd-Path: /boot/uInitrd Boot-DTB-Path: /boot/dtb Required-Packages: u-boot-tools Bootloader-Sets-Incorrect-Root: no
update-initramfs -u
e2label /dev/sda2 rootfs
exit reboot
printenv; ide reset; ext2load ide 2:1 0x0040000 uImage; ext2load ide 2:1 0x2000000 uInitrd; setenv bootargs $console $mtdparts root=/dev/sda2 rw rootdelay=10 bootm 0x40000 0x2000000
printenv; ide reset; ext2load ide 2:1 0x0040000 uImage; ext2load ide 2:1 0x2000000 uInitrd; setenv bootargs $console $mtdparts root=LABEL=rootfs rw rootdelay=5; bootm 0x40000 0x2000000
nanddump --noecc --omitoob -f mtd0 /dev/mtd0
setenv bootdebian 'printenv; ide reset; ext2load ide 2:1 0x0040000 uImage; ext2load ide 2:1 0x2000000 uInitrd; setenv bootargs $console $mtdparts root=LABEL=rootfs rw rootdelay=5; bootm 0x40000 0x2000000;'
bootcmd=nand read 0x40000 $kernel_start $kernel_size;nand read 0x2000000 $initrd_start $initrd_size;setenv bootargs $console $mtdparts $bootargs_root mem=512M ramdisk_size=$ramdisk_size ramdisk_blocksize=1024 ip=$bootargs_end $mvNetConfig; bootm 0x40000 0x2000000;
setenv bootcmd 'run bootdebian; reset;'
saveenv reset
Re: Mainline Debian on Iomega ix4-300d March 06, 2022 08:28AM |
Registered: 6 years ago Posts: 183 |
Marvell>> help ? - alias for 'help' SatR - Sample At Reset sub-system amp_boot- amp_boot - boot an AMP group amp_config- Fully config an AMP group amp_printenv- amp_printenv - print only AMP env variables amp_verify- Verfiy AMP configuration autoscr - DEPRECATED - use "source" command instead base - print or set address offset bdinfo - print Board Info structure bios - BIOS command to set the DB configuration. boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bubt - bubt - Burn an image on the Boot Nand Flash. chpart - change active partition cmp - memory compare cmpm - cmpm - Compare Memory coninfo - print console devices and information cp - memory copy cpumap - cpumap - Display CPU memory mapping settings. crc32 - checksum calculation date - get/set/reset date & time ddrPhyRead- ddrPhyRead - Read DDR PHY register ddrPhyWrite- ddrPhyWrite - Write DDR PHY register dhcp - boot image via network using DHCP/TFTP protocol diskboot- diskboot- boot from IDE device dma - dma - Perform DMA using the XOR engine echo - echo args to console eeprom - EEPROM sub-system exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fi - fi - Find value in the memory. fsinfo - print information about filesystems fsload - load binary file from a filesystem image g - g - start application at cached address 'addr'(default addr 0x40000) go - start application at address 'addr' help - print online help i2c - I2C sub-system ide - ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image ir - ir - reading and changing MV internal register values. itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range ls - list files in a directory (default /) map - map - Diasplay address decode windows md - memory display me - me - PCI master enable mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mp - mp - map PCI BAR mtdparts- define flash/nand partitions mtest - simple RAM read/write test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol nm - memory modify (constant address) pci - list and access PCI Configuration Space pciePhyRead- phyRead - Read PCI-E Phy register pciePhyWrite- pciePhyWrite - Write PCI-E Phy register phyRead - phyRead - Read Phy register phyWrite- phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol rcvr - rcvr - Satrt recovery process (Distress Beacon with TFTP server) reset - Perform RESET of the CPU resetenv- resetenv - earse environment sector to reset all variables to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage se - se - PCI Slave enable setenv - set environment variables sg - sg - scanning the PHYs status showvar - print local hushshell variables sleep - delay execution for some time source - run script from memory sp - sp - Scan PCI bus. temp - temp - Display the device temprature. test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol training- training - prints the results of the DDR3 Training. ts_report- ts_report - report touch screen cooridate ts_test - ts_test - test touch screen ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor version whoAmI - - reading CPU ID
Marvell>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 console=console=ttyS0,115200 mtdids=nand0=armada-nand CASset=min sata_delay_reset=0 MALLOC_len=5 ethprime=egiga0 bootargs_root=root=/dev/ram rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage serverip=192.168.1.100 ipaddr=192.168.1.2 loadpath=initrd.img ramdisk_size=4194304 ramdisk_size_f=12582912 ramdisk_name=initrd.img uver=v2.3.2.6 mfgmodel=IX4-300D autoload=yes ubin=0301 env_off=0xe0000 env1_off=0x100000 kernel_start=0x120000 initrd_start=0x520000 kernel_size=0x400000 initrd_size=0x400000 mtdparts=mtdparts=armada-nand:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; eth2addr=00:50:43:00:00:02 eth3addr=00:50:43:02:00:00 mv_pon_addr=00:50:43:02:00:00 ethmtu=1500 eth1mtu=1500 eth2mtu=1500 eth3mtu=1500 mvNetConfig=mv_net_config=2,(00:50:43:11:11:11,0:1),mtu=1500 usb0Mode=host usb1Mode=host usb2Mode=device usbActive=0 yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=yes rcvrip=169.254.100.100 loadaddr=0x02000000 eeeEnable=no lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 serial_number=5565U01001G324002A4J0G1 opid=Z12101594 ethaddr=00:D0:B8:24:CA:35 serialNo=EUD2400YA1 eth1addr=00:D0:B8:24:CA:36 modelname=32042300 serialno=0,01n4JkhykqG3IZ8edRG/eIuRK/8gSzpUIPiiS8zGSWduO1W4qix3a6I/vZ4/xT5WG0,EUD2400YA1, mfgtest_state=final_tested_ok runintime=14400 ftp_serverip=192.168.32.4 ftp_log_user=runinlog ftp_log_password=123 ftp_log_dir=storagelogs/soclogs/partlogs/IX4-300D/runin ftp_pass_user=qrypass ftp_pass_password=123 ftp_pass_dir=socquery ftp_qry_user=qrypass ftp_qry_password=123 ftp_qry_dir=socquery stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaClockGating=no enaWrAllo=no pexMode=RC disL2Cache=yes MPmode=SMP cacheShare=no setL2CacheWT=no disL2Prefetch=yes enaICPref=yes enaDCPref=yes enaFPU=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no amp_enable=no bootdelay=3 bootcmd=nand read 0x40000 $kernel_start $kernel_size;nand read 0x2000000 $initrd_start $initrd_size;setenv bootargs $console $mtdparts $bootargs_root mem=512M ramdisk_size=$ramdisk_size ramdisk_blocksize=1024 ip=$bootargs_end $mvNetConfig; bootm 0x40000 0x2000000; disaMvPnp=no enaAutoRecovery=yes pcieTune=no ethact=egiga0 Environment size: 2492/131067 bytes
BootROM 1.15 Booting from NAND flash DDR3 Training Sequence - Ver 2.3.4 DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER 2.3.2.6 ** U-Boot 2009.08 (Mar 04 2013 - 11:13:04) Marvell version: 2.3.2 PQ U-Boot Addressing: Code: 00600000:006BFFF0 BSS: 00708EC0 Stack: 0x5fff70 PageTable: 0x8e0000 Heap address: 0x900000:0xe00000 Board: DB-78230-BP rev 2.0 Wistron SoC: MV78230 A0 running 2 CPUs Custom configuration CPU: Marvell PJ4B (584) v7 (Rev 2) LE CPU # 0 CPU @ 1333Mhz, L2 @ 667Mhz DDR @ 667Mhz, TClock @ 250Mhz DDR 32Bit Width, FastPath Memory Access DDR ECC Disabled PEX 0.0(0): Root Complex Interface, Detected Link X4, GEN 1.1 PEX 1.0(1): Root Complex Interface, Detected Link X1, GEN 2.0 DRAM: 512 MB CS 0: base 0x00000000 size 512 MB Addresses 14M - 0M are saved for the U-Boot usage. NAND: 1024 MiB Bad block table found at page 524224, version 0x01 Bad block table found at page 524160, version 0x01 nand_read_bbt: Bad block at 0x000006c20000 nand_read_bbt: Bad block at 0x000013bc0000 nand_read_bbt: Bad block at 0x000029740000 nand_read_bbt: Bad block at 0x00002c040000 nand_read_bbt: Bad block at 0x0000346a0000 FPU initialized to Run Fast Mode. USB 0: Host Mode USB 1: Host Mode USB 2: Device Mode Modules Detected: MMC: MRVL_MMC: 0 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x120000, size 0x400000 4194304 bytes read: OK NAND read: device 0 offset 0x520000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00040000 ... Image Name: Linux-3.2.40 Created: 2020-01-02 11:18:50 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3656376 Bytes = 3.5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: Created: 2020-01-14 10:40:35 UTC Image Type: ARM Linux RAMDisk Image (bzip2 compressed) Data Size: 3012478 Bytes = 2.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Welcome to CenterPoint. ix4-300d login:
admin@ix4-300d:~$ dmesg Booting Linux on physical CPU 0 Initializing cgroup subsys cpu Linux version 3.2.40 (soho@bsoho083.iomegacorp.com) (gcc version 4.7.2 (crosstool-NG 1.20.0) ) #1 SMP Thu Jan 2 06:18:39 EST 2020 v2.1.1.1 CPU: Marvell PJ4Bv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache Machine: Marvell Armada XP Development Board Using UBoot passing parameters structure Reserving training memory: base=0x (null) size=0x2800 Memory policy: ECC disabled, Data cache writealloc On node 0 totalpages: 131072 free_area_init_node: node 0, pgdat c071ab40, node_mem_map c075a000 DMA zone: 1152 pages used for memmap DMA zone: 0 pages reserved DMA zone: 129920 pages, LIFO batch:31 SMP: init cpus PERCPU: Embedded 7 pages/cpu @c0bde000 s6336 r8192 d14144 u32768 pcpu-alloc: s6336 r8192 d14144 u32768 alloc=8*4096 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920 Kernel command line: console=ttyS0,115200 mtdparts=armada-nand:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) root=/dev/ram rw mem=512M ramdisk_size=4194304 ramdisk_blocksize=1024 ip=:::DB88FXX81:eth0:none mv_net_config=2,(00:50:43:11:11:11,0:1),mtu=1500 PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 508660k/508660k available, 15628k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfa800000 ( 416 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc06a7000 (6780 kB) .init : 0xc06a7000 - 0xc06de8c0 ( 223 kB) .data : 0xc06e0000 - 0xc071b620 ( 238 kB) .bss : 0xc071b644 - 0xc07597d4 ( 249 kB) Hierarchical RCU implementation. NR_IRQS:211 Initializing ArmadaXP SOC Timer 0 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 SMP: prepare CPUs (4 cores) Setting Clocks for secondary CPUs Armada-XP Performance Monitor Unit detected (Marvell ID)!!! hw perfevents: enabled with Armada PJ4 PMU driver, 7 counters available SMP: CPU 0 Waking up CPU 1 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (2664.03 BogoMIPS). xor: measuring software checksum speed arm4regs : 1088.000 MB/sec 8regs : 958.000 MB/sec 32regs : 1229.600 MB/sec xor: using function: 32regs (1229.600 MB/sec) NET: Registered protocol family 16 Aurora: Working in ARMv7 mode L0 cache Enabled Speculative Prefetch Disabled Aurora L2 Cache Enabled Support IO coherency. Marvell Armada-XP DB-78460-BP rev 2.0 Board - Soc: MV78230 A0 LE Detected Tclk 250000000, SysClk 667000000, FabricClk 667000000, PClk 1333000000 LSP version: linux-3.2.y-2013_Q1.2p2 registered dev#0 asa ehci_marvell Marvell USB EHCI Host controller #0: df857ec0 registered dev#1 asa ehci_marvell Marvell USB EHCI Host controller #1: df857dc0 registered dev#2 asa mv_udc Marvell USB Gadget controller #2: df857cc0 bio: create slab <bio-0> at 0 raid6: int32x1 144 MB/s raid6: int32x2 214 MB/s raid6: int32x4 217 MB/s raid6: int32x8 228 MB/s raid6: using algorithm int32x8 (228 MB/s) SCSI Staggered Spinup: SCSI Staggered Spinup Feature Status: Disabled SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Switching to clocksource axp_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 32 Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 2940K PCI-E: Cheking physical bus #0 (controller #0): Enabled - Link UP PCI-E: Cheking physical bus #1 (controller #4): Enabled - Link UP PCI-E: Cheking physical bus #2 (controller #5): Disabled PCI-E: Cheking physical bus #3 (controller #6): Disabled pci 0000:00:00.0: [11ab:7042] type 0 class 0x000100 pci 0000:00:00.0: reg 10: [mem 0x40000000-0x400fffff 64bit] pci 0000:00:00.0: reg 18: [io 0xf1100000-0xf11000ff] PCI: bus0: Fast back to back transfers disabled pci 0000:01:00.0: [1033:0194] type 0 class 0x000c03 pci 0000:01:00.0: reg 10: [mem 0x4a000000-0x4a001fff 64bit] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled PCI: bus1: Fast back to back transfers disabled pci 0000:01:00.0: BAR 0: assigned [mem 0xf2800000-0xf2801fff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0xf2800000-0xf2801fff 64bit] (PCI address [0xf2800000-0xf2801fff]) pci 0000:00:00.0: BAR 0: assigned [mem 0xf2000000-0xf20fffff 64bit] pci 0000:00:00.0: BAR 0: set to [mem 0xf2000000-0xf20fffff 64bit] (PCI address [0xf2000000-0xf20fffff]) pci 0000:00:00.0: BAR 2: can't assign io (size 0x100) CESA test started: bufNum = 1, bufSize = 20000 Cesa Test Start: pMbufSrc=df9be000, pFragsSrc=dfa90000, pMbufDst=df8f9000, pFragsDst=df0bc000 mvCesaInit: channels=2, session=32, queue=256 cesadev_init(c06afa6c) MV Buttons Driver Load MV Buttons : return ok MV Buttons : return ok MV Buttons : return ok MV Buttons : return ok Armada XP hwmon thermal sensor initialized. ArmadaXP Power Managament Suspend Operations Initialized Initializing Armada-XP CPU power management (WFI) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher Registering unionfs 2.5.11 (for 3.2.2) Registering the id_resolver key type Installing knfsd (copyright (C) 1996 okir@monad.swb.de). SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem msgmni has been set to 999 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Initializing ths8200_init Initializing dove_adi9889_init mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) mv_xor mv_xor.2: Marvell XOR: ( xor ) mv_xor mv_xor.3: Marvell XOR: ( fill cpy ) brd: module loaded loop: module loaded Loading iSCSI transport class v2.0-870. sata_mv 0000:00:00.0: version 1.28 sata_mv 0000:00:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx scsi0 : sata_mv scsi1 : sata_mv scsi2 : sata_mv scsi3 : sata_mv ata1: SATA max UDMA/133 mmio m1048576@0xf2000000 port 0xf2022000 irq 58 ata2: SATA max UDMA/133 mmio m1048576@0xf2000000 port 0xf2024000 irq 58 ata3: SATA max UDMA/133 mmio m1048576@0xf2000000 port 0xf2026000 irq 58 ata4: SATA max UDMA/133 mmio m1048576@0xf2000000 port 0xf2028000 irq 58 sata_mv sata_mv.0: version 1.28 sata_mv sata_mv.0: cannot get clkdev sata_mv sata_mv.0: slots 32 ports 2 scsi4 : sata_mv scsi5 : sata_mv ata5: SATA max UDMA/133 irq 55 ata6: SATA max UDMA/133 irq 55 INFO: Found spi_flash 0 - base 0xf6000000, size 0x1000000 INFO: flashInfoFill - Found 1 Flash Devices INFO: flash_map_init - detected 1 devices MTD: Initialize the spi_flash device at address 0xf6000000 INFO: Io remapped successfully - phy addr = 0xf6000000, virt addr = 0xe1000000 INFO: Using sflash to probe spi_flash at address 0xf6000000, size 0x1000000, width 2mmvSFlashInit ERROR: Unknown SPI flash device! ERROR: sflash_probe - Failed to initialize the SFlash. - Not detected - FAILED! armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit) Bad block table found at page 524224, version 0x01 Bad block table found at page 524160, version 0x01 nand_read_bbt: bad block at 0x000006c20000 nand_read_bbt: bad block at 0x000013bc0000 nand_read_bbt: bad block at 0x000029740000 nand_read_bbt: bad block at 0x00002c040000 nand_read_bbt: bad block at 0x0000346a0000 7 cmdlinepart partitions found on MTD device armada-nand 7 cmdlinepart partitions found on MTD device armada-nand Creating 7 MTD partitions on "armada-nand": 0x000000000000-0x0000000e0000 : "uboot" 0x0000000e0000-0x000000100000 : "env" 0x000000100000-0x000000120000 : "env2" 0x000000120000-0x000000520000 : "zImage" 0x000000520000-0x000000920000 : "initrd" 0x000000e00000-0x000040000000 : "boot" 0x000000000000-0x000040000000 : "flash" mv_eth_probe: port_mask=0xf, cpu_mask=0x3 o 2 Giga ports supported o SKB recycle supported (Enabled) o NETA acceleration mode 1 o RX Queue support: 8 Queues * 128 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Loading network interface(s) o Port 0 is connected to Linux netdevice giga p=0: mtu=1500, mac=df833e64 o eth0, ifindex = 2, GbE port = 0 o Port 1 is connected to Linux netdevice giga p=1: mtu=1500, mac=df833e64 o eth1, ifindex = 3, GbE port = 1 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> sky2: driver version 1.30 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.0: Marvell Orion EHCI ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.0: irq 45, io base 0xfbc50100 ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_marvell ehci_marvell.1: Marvell Orion EHCI ehci_marvell ehci_marvell.1: new USB bus registered, assigned bus number 2 ehci_marvell ehci_marvell.1: irq 46, io base 0xfbc51100 ehci_marvell ehci_marvell.1: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver xhci_hcd 0000:01:00.0: xHCI Host Controller xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 xhci_hcd 0000:01:00.0: irq 62, io mem 0xf2800000 xHCI xhci_add_endpoint called for root hub xHCI xhci_check_bandwidth called for root hub hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected xhci_hcd 0000:01:00.0: xHCI Host Controller xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 4 xHCI xhci_add_endpoint called for root hub xHCI xhci_check_bandwidth called for root hub hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0 pcf8563_init()~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ i2c /dev entries driver rtc-pcf8563 0-0051: chip found, driver version 0.4.3 rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable. rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc1 rtc init ok~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ adt7475 0-002e: ADT7473 device, revision 0 adt7475 0-002e: Optional features: fan4 pwm2 ADT7473 version = 0xfa68 md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver usbhid usbhid: USB HID core driver nf_conntrack version 0.5.0 (7993 buckets, 31972 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 Registering the dns_resolver key type VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 Registering SWP/SWPB emulation handler rtc-mv rtc-mv: setting system clock to 2022-02-14 21:54:49 UTC (1644875689) ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata5: failed to resume link (SControl 4) ata5: SATA link down (SStatus 0 SControl 4) ata4: SATA link down (SStatus 0 SControl 300) ata6: failed to resume link (SControl 4) ata6: SATA link down (SStatus 0 SControl 4) Warning: unable to open an initial console. md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. RAMDISK: bzip2 image found at block 0 EXT2-fs (ram0): warning: checktime reached, running e2fsck is recommended VFS: Mounted root (ext2 filesystem) on device 1:0. UBI: attaching mtd5 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 102921 UBI: attached mtd5 to ubi0 UBI: MTD device name: "boot" UBI: MTD device size: 1010 MiB UBI: number of good PEBs: 8067 UBI: number of bad PEBs: 13 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 8067 UBI: number of PEBs reserved for bad PEB handling: 80 UBI: max/mean erase counter: 18/13 UBI: image sequence number: 1545176087 UBI: background thread "ubi_bgt0d" started, PID 581 UBIFS: mounted UBI device 0, volume 0, name "boot" UBIFS: file system size: 1011490816 bytes (987784 KiB, 964 MiB, 7966 LEBs) UBIFS: journal size: 33521664 bytes (32736 KiB, 31 MiB, 264 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 4952683 bytes (4836 KiB) jnl: driver (lke_9.2.0, Aug 30 2019 09:19:25, LBD=ON) loaded at bf000000 ufsd: module license 'Commercial product' taints kernel. Disabling lock debugging due to kernel taint ufsd: driver (lke_9.2.0 lke_9.2.0_r256779_b61, build_host("bsoho083.iomegacorp.com"), acl, ioctl, bdi, sd2(0), fua, bz, rsrc, bh) loaded at bf00c000 NTFS support included Hfs+/HfsJ support included optimized: speed Build_for__LenovoEMC_ix4-300d_k3.2.40_2013-07-15_lke_9.2.0_r256779_b61 Bluetooth: Generic Bluetooth USB driver ver 0.6 usbcore: registered new interface driver btusb Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 usbcore: registered new interface driver usblp Freeing init memory: 220K Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 41) is a 16550A udevd[967]: starting version 175 pool #1: pkt_size=1536, buf_size=1632 - 2048 of 2048 buffers added eth1: link up eth1: link up, full duplex, speed 1 Gbps eth1: started pool #0: pkt_size=1536, buf_size=1632 - 2048 of 2048 buffers added eth0: started rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable. md: md1 stopped. admin@ix4-300d:~$
Re: Mainline Debian on Iomega ix4-300d March 06, 2022 01:22PM |
Registered: 6 years ago Posts: 183 |
# This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). source /etc/network/interfaces.d/* # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 192.168.1.80 gateway 192.168.1.254
[ 21.383041] mvneta d0070000.ethernet eth0: PHY [d0072004.mdio-mii:00] driver [Marvell 88E1318S] (irq=POLL) [ 21.393138] mvneta d0070000.ethernet eth0: configuring for phy/rgmii-id link mode [ 25.501737] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 25.509822] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.210032] mvneta d0074000.ethernet eth1: PHY [d0072004.mdio-mii:01] driver [Marvell 88E1318S] (irq=POLL) [ 31.220104] mvneta d0074000.ethernet eth1: configuring for phy/rgmii-id link mode
Mar 06 19:09:42 ix4-300d systemd[1]: Starting Raise network interfaces... Mar 06 19:09:42 ix4-300d ifup[646]: ifup: failed to bring up lo Mar 06 19:09:42 ix4-300d ifup[646]: ifup: waiting for lock on /run/network/ifstate.eth0 Mar 06 19:09:52 ix4-300d ifup[709]: RTNETLINK answers: File exists Mar 06 19:09:52 ix4-300d ifup[646]: ifup: failed to bring up eth1 Mar 06 19:09:52 ix4-300d systemd[1]: networking.service: Main process exited, code=exited, status=1/FAILURE Mar 06 19:09:52 ix4-300d systemd[1]: networking.service: Failed with result 'exit-code'. Mar 06 19:09:52 ix4-300d systemd[1]: Failed to start Raise network interfaces.
Re: Mainline Debian on Iomega ix4-300d March 06, 2022 04:24PM |
Admin Registered: 13 years ago Posts: 18,821 |
mtdparts=mtdparts=armada-nand:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash)
cat /etc/fw_env.config
fw_printenv
Re: Mainline Debian on Iomega ix4-300d March 07, 2022 03:36PM |
Registered: 6 years ago Posts: 183 |
Re: Mainline Debian on Iomega ix4-300d March 07, 2022 05:38PM |
Admin Registered: 13 years ago Posts: 18,821 |
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x00000 0x20000 0x20000
Re: Mainline Debian on Iomega ix4-300d March 08, 2022 04:39PM |
Registered: 6 years ago Posts: 183 |
koen@ix4-300d:~$ cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x00000 0x20000 0x20000
koen@ix4-300d:~$ sudo fw_printenv Cannot read environment, using default Cannot read default environment from file
Re: Mainline Debian on Iomega ix4-300d March 08, 2022 07:04PM |
Admin Registered: 13 years ago Posts: 18,821 |
dmesg | grep 0x0 cat /proc/mtd
Re: Mainline Debian on Iomega ix4-300d March 09, 2022 03:36PM |
Registered: 6 years ago Posts: 183 |
koen@ix4-300d:~$ sudo dmesg | grep 0x0 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] cma: Reserved 16 MiB at 0x000000001f000000 [ 0.000000] DMA [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=pxa3xx_nand-0:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) root=LABEL=rootfs rw rootdelay=5 [ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12 [ 2.642407] mvebu-pcie soc:pcie@82000000: MEM 0x00d0040000..0x00d0041fff -> 0x0000040000 [ 2.642437] mvebu-pcie soc:pcie@82000000: MEM 0x00d0044000..0x00d0045fff -> 0x0000044000 [ 2.642463] mvebu-pcie soc:pcie@82000000: MEM 0x00d0048000..0x00d0049fff -> 0x0000048000 [ 2.642489] mvebu-pcie soc:pcie@82000000: MEM 0x00d004c000..0x00d004dfff -> 0x000004c000 [ 2.642516] mvebu-pcie soc:pcie@82000000: MEM 0x00d0080000..0x00d0081fff -> 0x0000080000 [ 2.642542] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 2.642566] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 2.642590] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 2.642615] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 2.642639] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 2.642663] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 2.642687] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 2.642711] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 2.642734] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 2.642751] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 2.643075] pci_bus 0000:00: root bus resource [mem 0xd0040000-0xd0041fff] (bus address [0x00040000-0x00041fff]) [ 2.643086] pci_bus 0000:00: root bus resource [mem 0xd0044000-0xd0045fff] (bus address [0x00044000-0x00045fff]) [ 2.643098] pci_bus 0000:00: root bus resource [mem 0xd0048000-0xd0049fff] (bus address [0x00048000-0x00049fff]) [ 2.643109] pci_bus 0000:00: root bus resource [mem 0xd004c000-0xd004dfff] (bus address [0x0004c000-0x0004dfff]) [ 2.643120] pci_bus 0000:00: root bus resource [mem 0xd0080000-0xd0081fff] (bus address [0x00080000-0x00081fff]) [ 2.643241] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400 [ 2.643745] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400 [ 2.645104] pci 0000:01:00.0: [11ab:7042] type 00 class 0x010000 [ 2.646660] pci 0000:02:00.0: [1033:0194] type 00 class 0x0c0330 [ 4.560795] mtdparts=pxa3xx_nand-0:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) [ 5.298239] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004 [ 18.929281] Bad block table found at page 524224, version 0x01 [ 18.988446] Bad block table found at page 524160, version 0x01 [ 19.005404] nand_read_bbt: bad block at 0x000006c20000 [ 19.010693] nand_read_bbt: bad block at 0x000013bc0000 [ 19.015904] nand_read_bbt: bad block at 0x000029740000 [ 19.021095] nand_read_bbt: bad block at 0x00002c040000 [ 19.026283] nand_read_bbt: bad block at 0x0000346a0000 [ 19.238807] 0x000000000000-0x0000000e0000 : "u-boot" [ 19.258550] 0x0000000e0000-0x000000100000 : "u-boot-env" [ 19.295783] 0x000000100000-0x000000120000 : "u-boot-env2" [ 19.322790] 0x000000120000-0x000000520000 : "zImage" [ 19.358044] 0x000000520000-0x000000920000 : "initrd" [ 19.382045] 0x000000e00000-0x000040000000 : "boot"
koen@ix4-300d:~$ cat /proc/mtd dev: size erasesize name mtd0: 000e0000 00020000 "u-boot" mtd1: 00020000 00020000 "u-boot-env" mtd2: 00020000 00020000 "u-boot-env2" mtd3: 00400000 00020000 "zImage" mtd4: 00400000 00020000 "initrd" mtd5: 3f200000 00020000 "boot"
koen@ix4-300d:~$ cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x00000 0x20000 0x20000
koen@ix4-300d:~$ fw_printenv Configuration file wrong or corrupted koen@ix4-300d:~$ sudo fw_printenv Cannot read environment, using default Cannot read default environment from file
Re: Mainline Debian on Iomega ix4-300d March 09, 2022 03:51PM |
Registered: 6 years ago Posts: 183 |
koen@ix4-300d:~$ sudo systemctl reboot [sudo] password for koen: Stoppin[ OK ] Removed slice system-modprobe.slice. [ OK ] Stopped target Graphical Interface. [ OK ] Stopped target Multi-User System. [ OK ] Stopped target Login Prompts. [ OK ] Stopped target Timers. [ OK ] Stopped Daily apt upgrade and clean activities. [ OK ] Stopped Daily apt download activities. [ OK ] Stopped Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Stopped Discard unused blocks once a week. [ OK ] Stopped Daily rotation of log files. [ OK ] Stopped Daily exim4-base housekeeping. [ OK ] Stopped Daily man-db regeneration. [ OK ] Stopped Daily Cleanup of Temporary Directories. Stopping Regular background program processing daemon... Stopping LSB: exim Mail Transport Agent... Stopping Getty on tty1... [ OK ] Stopped Initialize hardware monitoring sensors. Stopping System Logging Service... Stopping Serial Getty on ttyS0... Stopping Self Monitoring a…g Technology (SMART) Daemon... Stopping OpenBSD Secure Shell server... Stopping Load/Save Random Seed... [ OK ] Stopped Regular background program processing daemon. [ OK ] Stopped System Logging Service. [ OK ] Stopped Self Monitoring an…ing Technology (SMART) Daemon. [ OK ] Stopped Getty on tty1. [ OK ] Stopped Serial Getty on ttyS0. [ OK ] Stopped OpenBSD Secure Shell server. [ OK ] Stopped Load/Save Random Seed. [ OK ] Stopped Session 3 of user koen. [ OK ] Removed slice system-getty.slice. [ OK ] Removed slice system-serial\x2dgetty.slice. Stopping User Login Management... Stopping User Manager for UID 1000... [ OK ] Stopped User Manager for UID 1000. Stopping User Runtime Directory /run/user/1000... [ OK ] Stopped User Login Management. [ OK ] Unmounted /run/user/1000. [ OK ] Stopped LSB: exim Mail Transport Agent. [ OK ] Stopped User Runtime Directory /run/user/1000. [ OK ] Removed slice User Slice of UID 1000. [ OK ] Stopped target Network is Online. [ OK ] Stopped target System Time Synchronized. [ OK ] Stopped target System Time Set. Stopping D-Bus System Message Bus... Stopping Permit User Sessions... [ OK ] Stopped D-Bus System Message Bus. [ OK ] Stopped Permit User Sessions. [ OK ] Stopped target Basic System. [ OK ] Stopped target Network. [ OK ] Stopped target Paths. [ OK ] Stopped target Remote File Systems. [ OK ] Stopped target Slices. [ OK ] Removed slice User and Session Slice. [ OK ] Stopped target Sockets. [ OK ] Closed D-Bus System Message Bus Socket. [ OK ] Stopped target System Initialization. [ OK ] Stopped target Local Encrypted Volumes. [ OK ] Stopped Dispatch Password …ts to Console Directory Watch. [ OK ] Stopped Forward Password R…uests to Wall Directory Watch. [ OK ] Stopped target Swap. [ OK ] Closed Syslog Socket. Deactivating swap /dev/dis…_151281110001024706B1-part5... Stopping ifup for eth0... Stopping Network Time Synchronization... Stopping Update UTMP about System Boot/Shutdown... [ OK ] Deactivated swap /dev/disk…ci-0000:01:00.0-ata-1.0-part5. [ OK ] Deactivated swap /dev/disk/by-partuuid/20f65b3e-05. [ OK ] Deactivated swap /dev/disk…-pci-0000:01:00.0-ata-1-part5. [ OK ] Deactivated swap /dev/disk…SD_151281110001024706B1-part5. [ OK ] Deactivated swap /dev/sda5. [ OK ] Stopped Network Time Synchronization. [ OK ] Deactivated swap /dev/disk…5-31f0-40ca-ad64-f0b09c78a75b. [ OK ] Stopped Update UTMP about System Boot/Shutdown. [ OK ] Stopped Create Volatile Files and Directories. [ 335.370811] mvneta d0070000.ethernet eth0: Link is Down [ OK ] Stopped ifup for eth0. [ OK ] Stopped target Local File Systems. Unmounting /boot... Unmounting /mnt/md0... [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped Load Kernel Modules. [ OK ] Unmounted /boot. [ OK ] Stopped File System Check …a-583d-4349-8eb5-b33d046cda26. [ OK ] Removed slice system-systemd\x2dfsck.slice. [ OK ] Unmounted /mnt/md0. [ OK ] Stopped target Local File Systems (Pre). [ OK ] Reached target Unmount All Filesystems. [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Create System Users. [ OK ] Stopped Remount Root and Kernel File Systems. [ OK ] Reached target Shutdown. [ OK ] Reached target Final Step. [ OK ] Finished Reboot. [ OK ] Reached target Reboot. [ 339.741280] systemd-shutdown[1]: Syncing filesystems and block devices. [ 339.790133] systemd-shutdown[1]: Sending SIGTERM to remaining processes... [ 339.809908] systemd-journald[223]: Received SIGTERM from PID 1 (systemd-shutdow). [ 339.964219] systemd-shutdown[1]: Sending SIGKILL to remaining processes... [ 340.136881] systemd-shutdown[1]: Using hardware watchdog 'Orion Watchdog', version 0, device /dev/watchdog [ 340.150626] systemd-shutdown[1]: Unmounting file systems. [ 340.159388] [1458]: Remounting '/' read-only in with options 'errors=remount-ro'. [ 340.188535] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 340.206131] systemd-shutdown[1]: All filesystems unmounted. [ 340.211804] systemd-shutdown[1]: Deactivating swaps. [ 340.218287] systemd-shutdown[1]: All swaps deactivated. [ 340.223704] systemd-shutdown[1]: Detaching loop devices. [ 340.229535] systemd-shutdown[1]: All loop devices detached. [ 340.235169] systemd-shutdown[1]: Stopping MD devices. [ 340.241750] systemd-shutdown[1]: Stopping MD /dev/md0 (9:0). [ 340.391135] md0: detected capacity change from 4000525058048 to 0 [ 340.397284] md: md0 stopped. [ 340.447989] systemd-shutdown[1]: All MD devices stopped. [ 340.453560] systemd-shutdown[1]: Detaching DM devices. [ 340.459507] systemd-shutdown[1]: All DM devices detached. [ 340.465005] systemd-shutdown[1]: All filesystems, swaps, loop devices, MD devices and DM devices detached. [ 340.499503] systemd-shutdown[1]: Syncing filesystems and block devices. [ 340.506462] systemd-shutdown[1]: Rebooting. [ 340.526222] sd 3:0:0:0: [sdd] Synchronizing SCSI cache [ 340.533826] sd 2:0:0:0: [sdc] Synchronizing SCSI cache [ 340.541415] sd 1:0:0:0: [sdb] Synchronizing SCSI cache [ 340.548966] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 340.575846] reboot: Restarting system BootROM 1.15 Booting from NAND flash DDR3 Training Sequence - Ver 2.3.4 DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER 2.3.2.6 ** U-Boot 2009.08 (Mar 04 2013 - 11:13:04) Marvell version: 2.3.2 PQ U-Boot Addressing: Code: 00600000:006BFFF0 BSS: 00708EC0 Stack: 0x5fff70 PageTable: 0x8e0000 Heap address: 0x900000:0xe00000 Board: DB-78230-BP rev 2.0 Wistron SoC: MV78230 A0 running 2 CPUs Custom configuration CPU: Marvell PJ4B (584) v7 (Rev 2) LE CPU # 0 CPU @ 1333Mhz, L2 @ 667Mhz DDR @ 667Mhz, TClock @ 250Mhz DDR 32Bit Width, FastPath Memory Access DDR ECC Disabled PEX 0.0(0): Root Complex Interface, Detected Link X4, GEN 1.1 PEX 1.0(1): Root Complex Interface, Detected Link X1, GEN 2.0 DRAM: 512 MB CS 0: base 0x00000000 size 512 MB Addresses 14M - 0M are saved for the U-Boot usage. NAND: 1024 MiB Bad block table found at page 524224, version 0x01 Bad block table found at page 524160, version 0x01 nand_read_bbt: Bad block at 0x000006c20000 nand_read_bbt: Bad block at 0x000013bc0000 nand_read_bbt: Bad block at 0x00001ff00000 nand_read_bbt: Bad block at 0x0000268a0000 nand_read_bbt: Bad block at 0x000029740000 nand_read_bbt: Bad block at 0x00002c040000 nand_read_bbt: Bad block at 0x0000346a0000 FPU initialized to Run Fast Mode. USB 0: Host Mode USB 1: Host Mode USB 2: Device Mode Modules Detected: MMC: MRVL_MMC: 0 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Unknown command 'printenv' - try 'help' Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found Found adapter at bus 0, device 1 ... Scanning channels Device 2 @ 1 0: Model: Corsair Force LS SSD Firm: S9FM02.0 Ser#: 151281110001024706B1 Type: Hard Disk Supports 48-bit addressing Capacity: 57241.8 MB = 55.9 GB (117231408 x 512) Device 3 @ 1 1: Model: ST2000DM001-9YN164 Firm: CC4B Ser#: W1E451DL Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 4 @ 1 2: Model: ST2000DM001-9YN164 Firm: CC4B Ser#: W1E452BM Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 5 @ 1 3: Model: ST2000DM001-9YN164 Firm: CC4B Ser#: W1E451GB Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Loading file "uImage" from ide device 2:1 (hdc1) 5047775 bytes read Loading file "uInitrd" from ide device 2:1 (hdc1) 24664484 bytes read ## Booting kernel from Legacy Image at 00040000 ... Image Name: kernel 5.10.0-12-armmp-lpae Created: 2022-03-09 21:15:41 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5047711 Bytes = 4.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: ramdisk 5.10.0-12-armmp-lpae Created: 2022-03-09 21:15:41 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 24664420 Bytes = 23.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.0-12-armmp-lpae (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Debian 5.10.103-1 (2022-03-07) [ 0.000000] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Lenovo Iomega ix4-300d [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x000000001f000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=pxa3xx_nand-0:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) root=LABEL=rootfs rw rootdelay=5 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 458040K/524288K available (12288K kernel code, 1680K rwdata, 3212K rodata, 2048K init, 343K bss, 49864K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] random: get_random_u32 called from __kmem_cache_create+0x30/0x450 with crng_init=0 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 37766 entries in 111 pages [ 0.000000] ftrace: allocated 111 pages with 6 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x1a696b10 -> 0x1a696b12 [ 0.000000] Aurora cache controller enabled, 16 ways, 1024 kB [ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000006] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.000019] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.001338] Console: colour dummy device 80x30 [ 0.001379] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.001395] pid_max: default: 32768 minimum: 301 [ 0.001632] LSM: Security Framework initializing [ 0.001710] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.001855] AppArmor: AppArmor initialized [ 0.001868] TOMOYO Linux initialized [ 0.001938] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001951] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002789] CPU: Testing write buffer coherency: ok [ 0.003023] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.003860] Setting up static identity map for 0x400000 - 0x4000ac [ 0.004222] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x1 [ 0.004321] mvebu-pmsu: Initializing Power Management Service Unit [ 0.004464] rcu: Hierarchical SRCU implementation. [ 0.005811] EFI services will not be available. [ 0.006085] smp: Bringing up secondary CPUs ... [ 0.006603] Booting CPU 1 [ 0.007036] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011126] smp: Brought up 1 node, 2 CPUs [ 0.011141] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.011148] CPU: All CPU(s) started in SVC mode. [ 0.011734] devtmpfs: initialized [ 0.015650] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.015871] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.015904] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.016814] pinctrl core: initialized pinctrl subsystem [ 0.017590] DMI not present or invalid. [ 0.017873] NET: Registered protocol family 16 [ 0.020150] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.020835] audit: initializing netlink subsys (disabled) [ 0.021819] thermal_sys: Registered thermal governor 'fair_share' [ 0.021827] thermal_sys: Registered thermal governor 'bang_bang' [ 0.021837] thermal_sys: Registered thermal governor 'step_wise' [ 0.021845] thermal_sys: Registered thermal governor 'user_space' [ 0.021852] thermal_sys: Registered thermal governor 'power_allocator' [ 0.022135] No ATAGs? [ 0.022177] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 [ 0.022187] hw-breakpoint: CPU 0 failed to disable vector catch [ 0.022223] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1 [ 0.022229] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 [ 0.022988] Serial: AMBA PL011 UART driver [ 0.043444] Kprobes globally optimized [ 0.043985] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 1.511133] iommu: Default domain type: Translated [ 1.511657] vgaarb: loaded [ 1.512336] mc: Linux media interface: v0.10 [ 1.512372] videodev: Linux video capture interface: v2.00 [ 1.513541] NetLabel: Initializing [ 1.513552] NetLabel: domain hash size = 128 [ 1.513559] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 1.513631] NetLabel: unlabeled traffic allowed by default [ 1.513942] clocksource: Switched to clocksource armada_370_xp_clocksource [ 1.580542] VFS: Disk quotas dquot_6.6.0 [ 1.580625] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.581297] AppArmor: AppArmor Filesystem Enabled [ 1.590437] NET: Registered protocol family 2 [ 1.590546] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.591537] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.591576] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.591621] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.591657] TCP: Hash tables configured (established 4096 bind 4096) [ 1.591752] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.591776] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.591924] NET: Registered protocol family 1 [ 1.591951] NET: Registered protocol family 44 [ 1.591966] PCI: CLS 0 bytes, default 64 [ 1.592289] Trying to unpack rootfs image as initramfs... [ 2.626080] Freeing initrd memory: 24088K [ 2.626552] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.627952] Initialise system trusted keyrings [ 2.627991] Key type blacklist registered [ 2.628186] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 2.634664] zbud: loaded [ 2.635510] integrity: Platform Keyring initialized [ 2.635528] Key type asymmetric registered [ 2.635537] Asymmetric key parser 'x509' registered [ 2.635577] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 2.635763] io scheduler mq-deadline registered [ 2.639002] armada-xp-pinctrl d0018000.pin-ctrl: registered pinctrl driver [ 2.642245] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: [ 2.642289] mvebu-pcie soc:pcie@82000000: MEM 0x00d0040000..0x00d0041fff -> 0x0000040000 [ 2.642318] mvebu-pcie soc:pcie@82000000: MEM 0x00d0044000..0x00d0045fff -> 0x0000044000 [ 2.642344] mvebu-pcie soc:pcie@82000000: MEM 0x00d0048000..0x00d0049fff -> 0x0000048000 [ 2.642371] mvebu-pcie soc:pcie@82000000: MEM 0x00d004c000..0x00d004dfff -> 0x000004c000 [ 2.642397] mvebu-pcie soc:pcie@82000000: MEM 0x00d0080000..0x00d0081fff -> 0x0000080000 [ 2.642423] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 2.642447] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 2.642471] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 2.642496] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 2.642520] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 2.642544] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 2.642568] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 2.642592] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 2.642615] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 2.642632] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 2.642927] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 [ 2.642944] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.642957] pci_bus 0000:00: root bus resource [mem 0xd0040000-0xd0041fff] (bus address [0x00040000-0x00041fff]) [ 2.642968] pci_bus 0000:00: root bus resource [mem 0xd0044000-0xd0045fff] (bus address [0x00044000-0x00045fff]) [ 2.642979] pci_bus 0000:00: root bus resource [mem 0xd0048000-0xd0049fff] (bus address [0x00048000-0x00049fff]) [ 2.642990] pci_bus 0000:00: root bus resource [mem 0xd004c000-0xd004dfff] (bus address [0x0004c000-0x0004dfff]) [ 2.643002] pci_bus 0000:00: root bus resource [mem 0xd0080000-0xd0081fff] (bus address [0x00080000-0x00081fff]) [ 2.643011] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 2.643021] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 2.643122] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400 [ 2.643624] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400 [ 2.644806] PCI: bus0: Fast back to back transfers disabled [ 2.644821] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.644837] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.644983] pci 0000:01:00.0: [11ab:7042] type 00 class 0x010000 [ 2.645016] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x400fffff 64bit] [ 2.645034] pci 0000:01:00.0: reg 0x18: [io 0xf1100000-0xf11000ff] [ 2.645313] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 2.646380] PCI: bus1: Fast back to back transfers disabled [ 2.646395] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.646540] pci 0000:02:00.0: [1033:0194] type 00 class 0x0c0330 [ 2.646573] pci 0000:02:00.0: reg 0x10: [mem 0x4a000000-0x4a001fff 64bit] [ 2.646705] pci 0000:02:00.0: PME# supported from D0 D3hot [ 2.659012] PCI: bus2: Fast back to back transfers disabled [ 2.659028] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.659089] pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff] [ 2.659106] pci 0000:00:05.0: BAR 8: assigned [mem 0xf8100000-0xf81fffff] [ 2.659117] pci 0000:00:01.0: BAR 7: assigned [io 0x10000-0x10fff] [ 2.659134] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf80fffff 64bit] [ 2.659154] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x100ff] [ 2.659167] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.659177] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 2.659190] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 2.659209] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf8101fff 64bit] [ 2.659227] pci 0000:00:05.0: PCI bridge to [bus 02] [ 2.659239] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff] [ 2.659317] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 2.659410] pcieport 0000:00:05.0: enabling device (0140 -> 0142) [ 2.662793] mv_xor d0060900.xor: Marvell shared XOR driver [ 2.691108] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 2.691493] mv_xor d00f0900.xor: Marvell shared XOR driver [ 2.719103] mv_xor d00f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 2.721617] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.723898] printk: console [ttyS0] disabled [ 2.744076] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 28, base_baud = 15625000) is a 16550A [ 3.917073] printk: console [ttyS0] enabled [ 3.922255] Serial: AMBA driver [ 3.926367] STM32 USART driver initialized [ 3.933835] mousedev: PS/2 mouse device common for all mice [ 3.940713] rtc-mv d0010300.rtc: registered as rtc0 [ 3.945657] rtc-mv d0010300.rtc: setting system clock to 2022-03-09T21:32:26 UTC (1646861546) [ 4.059338] ledtrig-cpu: registered to indicate activity on CPUs [ 4.066658] NET: Registered protocol family 10 [ 4.113221] Segment Routing with IPv6 [ 4.117077] mip6: Mobile IPv6 [ 4.120118] NET: Registered protocol family 17 [ 4.124758] mpls_gso: MPLS GSO support [ 4.128667] ThumbEE CPU extension supported. [ 4.132990] Registering SWP/SWPB emulation handler [ 4.137989] registered taskstats version 1 [ 4.142126] Loading compiled-in X.509 certificates [ 4.484500] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 4.493348] Loaded X.509 cert 'Debian Secure Boot Signer 2021 - linux: 4b6ef5abca669825178e052c84667ccbc0531f8c' [ 4.503697] zswap: loaded using pool lzo/zbud [ 4.508644] Key type ._fscrypt registered [ 4.512724] Key type .fscrypt registered [ 4.516681] Key type fscrypt-provisioning registered [ 4.521872] AppArmor: AppArmor sha1 policy hashing enabled [ 4.531444] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.546340] Freeing unused kernel memory: 2048K [ 4.563858] Checked W+X mappings: passed, no W+X pages found [ 4.569574] Run /init as init process Loading, please wait... Starting version 247.3-6 Segmentation fault Begin: Loading essential drivers ... [ 4.840292] md_mod: module verification failed: signature and/or required key missing - tainting kernel [ 5.101969] raid6: int32x8 gen() 395 MB/s [ 5.173968] raid6: int32x8 xor() 255 MB/s [ 5.245968] raid6: int32x4 gen() 433 MB/s [ 5.317944] raid6: int32x4 xor() 261 MB/s [ 5.389943] raid6: int32x2 gen() 545 MB/s [ 5.461953] raid6: int32x2 xor() 288 MB/s [ 5.533955] raid6: int32x1 gen() 533 MB/s [ 5.605969] raid6: int32x1 xor() 253 MB/s [ 5.610267] raid6: using algorithm int32x2 gen() 545 MB/s [ 5.615696] raid6: .... xor() 288 MB/s, rmw enabled [ 5.620601] raid6: using intx1 recovery algorithm [ 5.628397] xor: measuring software checksum speed [ 5.640667] arm4regs : 1333 MB/sec [ 5.655106] 8regs : 980 MB/sec [ 5.667835] 32regs : 1184 MB/sec [ 5.672219] xor: using function: arm4regs (1333 MB/sec) [ 5.704821] async_tx: api initialized (async) done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Begin: Waiting for suspend/resume device ... Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. mdadm: No devices listed in conf file were found. mdadm: No devices listed in conf file were found. mdadm: No devices listed in conf file were found. mdadm: No devices listed in conf file were found. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. mdadm: No devices listed in conf file were found. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. mdadm: error opening /dev/md?*: No such file or directory mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. mdadm: No devices listed in conf file were found. done. Gave up waiting for suspend/resume device done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... mdadm: No devices listed in conf file were found. done. done. Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - M[ 37.166668] random: fast init done issing modules (cat /proc/modules; ls /dev) ALERT! LABEL=rootfs does not exist. Dropping to a shell! BusyBox v1.30.1 (Debian 1:1.30.1-6+b3) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs)
Re: Mainline Debian on Iomega ix4-300d March 09, 2022 04:16PM |
Registered: 6 years ago Posts: 183 |
Re: Mainline Debian on Iomega ix4-300d March 09, 2022 05:09PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
Increasing rootdelay to 10 gives the drives enough time to spin up / initialise and fixes the reboot issue.
Quote
I've hooked up serial and changed the mtdparts environment to the new settings. As far as I can see the correct mtd are defined in the Debian dmesg but fw_printenv does not work unfortunately.
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x00000 0x20000 0x20000 /dev/mtd2 0x00000 0x20000 0x20000
Re: Mainline Debian on Iomega ix4-300d March 09, 2022 05:28PM |
Registered: 6 years ago Posts: 183 |
koen@ix4-300d:~$ sudo fw_printenv bootdebian=printenv; ide reset; ext2load ide 2:1 0x0040000 uImage; ext2load ide 2:1 0x2000000 uInitrd; setenv bootargs $console $mtdparts root=LABEL=rootfs rw rootdelay=5; bootm 0x40000 0x2000000; bootnand=run loadnand; run loadargs; bootm 0x40000 0x2000000; loadargs=setenv bootargs $console $mtdparts $bootargs_root mem=512M ramdisk_size=$ramdisk_size ramdisk_blocksize=1024 ip=$bootargs_end $mvNetConfig; loadargs=setenv bootargs $console $mtdparts $bootargs_root mem=512M ramdisk_size=$ramdisk_size ramdisk_blocksize=1024 ip=$bootargs_end $mvNetConfig; loadnand=nand read 0x40000 $kernel_start $kernel_size;nand read 0x2000000 $initrd_start $initrd_size; loadnand=nand read 0x40000 $kernel_start $kernel_size;nand read 0x2000000 $initrd_start $initrd_size; CASset=min MALLOC_len=5 MPmode=SMP amp_enable=no autoload=yes baudrate=115200 bootargs_end=:::DB88FXX81:eth0:none bootargs_root=root=/dev/ram rw bootcmd=run bootdebian; reset; bootdebian=printenv; ide reset; ext2load ide 2:1 0x0040000 uImage; ext2load ide 2:1 0x2000000 uInitrd; setenv bootargs $console $mtdparts root=LABEL=rootfs rw rootdelay=10; bootm 0x40000 0x2000000; bootdelay=3 cacheShare=no console=console=ttyS0,115200 disL2Cache=yes disL2Prefetch=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaCpuStream=no enaDCPref=yes enaFPU=yes enaICPref=yes enaMonExt=no enaWrAllo=no env1_off=0x100000 env_off=0xe0000 eth1addr=00:D0:B8:24:CA:36 eth1mtu=1500 eth2addr=00:50:43:00:00:02 eth2mtu=1500 eth3addr=00:50:43:02:00:00 eth3mtu=1500 ethact=egiga0 ethaddr=00:D0:B8:24:CA:35 ethmtu=1500 ethprime=egiga0 ftp_log_dir=storagelogs/soclogs/partlogs/IX4-300D/runin ftp_log_password=123 ftp_log_user=runinlog ftp_pass_dir=socquery ftp_pass_password=123 ftp_pass_user=qrypass ftp_qry_dir=socquery ftp_qry_password=123 ftp_qry_user=qrypass ftp_serverip=192.168.32.4 image_name=uImage initrd_size=0x400000 initrd_start=0x520000 ipaddr=192.168.1.2 kernel_size=0x400000 kernel_start=0x120000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x02000000 loadpath=initrd.img loads_echo=0 mfgmodel=IX4-300D mfgtest_state=final_tested_ok modelname=32042300 mtdids=nand0=armada-nand mtdparts=mtdparts=pxa3xx_nand-0:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) mvNetConfig=mv_net_config=2,(00:50:43:11:11:11,0:1),mtu=1500 mv_pon_addr=00:50:43:02:00:00 nandEcc=1bit netbsd_en=no netmask=255.255.255.0 netretry=yes opid=Z12101594 pcieTune=no pexMode=RC ramdisk_name=initrd.img ramdisk_size=4194304 ramdisk_size_f=12582912 rcvrip=169.254.100.100 rootpath=/mnt/ARM_FS/ runintime=14400 sata_delay_reset=0 sata_dma_mode=yes serialNo=EUD2400YA1 serial_number=5565U01001G324002A4J0G1 serialno=0,01n4JkhykqG3IZ8edRG/eIuRK/8gSzpUIPiiS8zGSWduO1W4qix3a6I/vZ4/xT5WG0,EUD2400YA1, serverip=192.168.1.100 setL2CacheWT=no standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial ubin=0301 usb0Mode=host usb1Mode=host usb2Mode=device usbActive=0 uver=v2.3.2.6 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81
Re: Mainline Debian on Iomega ix4-300d March 09, 2022 05:47PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
listing them both fixes the issue and shows the uboot environment variables in Debian.
Quote
It also shows the slight mess I made in trying to re-write the original bootcmd into a bootnand sequence. In the end I decided not to use the stock firmware as a rescue system since I don't know if it would try to initialise the drives and wipe data etc.
mtd3: 00400000 00020000 "zImage" mtd4: 00400000 00020000 "initrd" mtd5: 3f200000 00020000 "boot"
Re: Mainline Debian on Iomega ix4-300d March 31, 2022 08:09AM |
Registered: 5 years ago Posts: 255 |
Re: Mainline Debian on Iomega ix4-300d September 23, 2022 05:00AM |
Registered: 1 year ago Posts: 6 |
Re: Mainline Debian on Iomega ix4-300d September 26, 2022 02:41PM |
Registered: 6 years ago Posts: 183 |
Re: Mainline Debian on Iomega ix4-300d September 27, 2022 10:32PM |
Admin Registered: 13 years ago Posts: 18,821 |
printenv help mtdparts
Re: Mainline Debian on Iomega ix4-300d October 05, 2022 02:01AM |
Registered: 1 year ago Posts: 6 |
Marvell>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 boardtest=1 console=console=ttyS0,115200 mtdids=nand0=armada-nand CASset=min sata_delay_reset=0 MALLOC_len=5 ethprime=egiga0 bootargs_root=root=/dev/ram rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage bootcmd=nand read 0x40000 $kernel_start $kernel_size; tftpboot 0x2000000 $ramdisk_name;setenv bootargs $console $mtdparts $bootargs_root ramdisk_size=$ramdisk_size_f ramdisk_blocksize=1024 ip=$bootargs_end $mvNetConfig;bootm 0x40000 0x2000000; loadpath=initrd.img ramdisk_size=4194304 ramdisk_size_f=12582912 ramdisk_name=initrd.img uver=v2.3.2.6 mfgmodel=IX4-300D autoload=yes ubin=0301 env_off=0xe0000 env1_off=0x100000 kernel_start=0x120000 initrd_start=0x520000 kernel_size=0x400000 initrd_size=0x400000 mtdparts=mtdparts=armada-nand:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; ethaddr=00:50:43:44:2a:32 eth1addr=00:50:43:2a:2a:32 eth2addr=00:50:43:2a:44:32 eth3addr=00:50:43:2a:44:2a mv_pon_addr=00:50:43:32:44:2a ethmtu=1500 eth1mtu=1500 eth2mtu=1500 eth3mtu=1500 mvNetConfig=mv_net_config=2,(00:50:43:11:11:11,0:1),mtu=1500 usb0Mode=host usb1Mode=host usb2Mode=device usbActive=0 yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=yes rcvrip=169.254.100.100 loadaddr=0x02000000 eeeEnable=no lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaClockGating=no enaWrAllo=no pexMode=RC disL2Cache=yes MPmode=SMP cacheShare=no setL2CacheWT=no disL2Prefetch=yes enaICPref=yes enaDCPref=yes enaFPU=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no amp_enable=no serverip=192.168.1.100 ipaddr=192.168.1.2 bootdelay=7 disaMvPnp=no enaAutoRecovery=yes pcieTune=no ethact=egiga0 Environment size: 2000/131067 bytes
Marvell>> help ? - alias for 'help' SatR - Sample At Reset sub-system amp_boot- amp_boot - boot an AMP group amp_config- Fully config an AMP group amp_printenv- amp_printenv - print only AMP env variables amp_verify- Verfiy AMP configuration autoscr - DEPRECATED - use "source" command instead base - print or set address offset bdinfo - print Board Info structure bios - BIOS command to set the DB configuration. boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bubt - bubt - Burn an image on the Boot Nand Flash. chpart - change active partition cmp - memory compare cmpm - cmpm - Compare Memory coninfo - print console devices and information cp - memory copy cpumap - cpumap - Display CPU memory mapping settings. crc32 - checksum calculation date - get/set/reset date & time ddrPhyRead- ddrPhyRead - Read DDR PHY register ddrPhyWrite- ddrPhyWrite - Write DDR PHY register dhcp - boot image via network using DHCP/TFTP protocol diskboot- diskboot- boot from IDE device dma - dma - Perform DMA using the XOR engine echo - echo args to console eeprom - EEPROM sub-system exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fi - fi - Find value in the memory. fsinfo - print information about filesystems fsload - load binary file from a filesystem image g - g - start application at cached address 'addr'(default addr 0x40000) go - start application at address 'addr' help - print online help i2c - I2C sub-system ide - ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image ir - ir - reading and changing MV internal register values. itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range ls - list files in a directory (default /) map - map - Diasplay address decode windows md - memory display me - me - PCI master enable mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mp - mp - map PCI BAR mtdparts- define flash/nand partitions mtest - simple RAM read/write test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol nm - memory modify (constant address) pci - list and access PCI Configuration Space pciePhyRead- phyRead - Read PCI-E Phy register pciePhyWrite- pciePhyWrite - Write PCI-E Phy register phyRead - phyRead - Read Phy register phyWrite- phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol rcvr - rcvr - Satrt recovery process (Distress Beacon with TFTP server) reset - Perform RESET of the CPU resetenv- resetenv - earse environment sector to reset all variables to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage se - se - PCI Slave enable setenv - set environment variables sg - sg - scanning the PHYs status showvar - print local hushshell variables sleep - delay execution for some time source - run script from memory sp - sp - Scan PCI bus. temp - temp - Display the device temprature. test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol training- training - prints the results of the DDR3 Training. ts_report- ts_report - report touch screen cooridate ts_test - ts_test - test touch screen ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor version whoAmI - - reading CPU ID
Marvell>> mtdparts cannot add second partition at offset 0
Re: Mainline Debian on Iomega ix4-300d October 05, 2022 11:22AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Mainline Debian on Iomega ix4-300d October 07, 2022 01:57AM |
Registered: 1 year ago Posts: 6 |
Re: Mainline Debian on Iomega ix4-300d October 09, 2022 07:45AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Mainline Debian on Iomega ix4-300d October 10, 2022 07:47AM |
Registered: 1 year ago Posts: 6 |
[Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER 2.3.2.6 ** U-Boot 2009.08 (Mar 04 2013 - 11:13:04) Marvell version: 2.3.2 PQ U-Boot Addressing: Code: 00600000:006BFFF0 BSS: 00708EC0 Stack: 0x5fff70 PageTable: 0x8e0000 Heap address: 0x900000:0xe00000 Board: DB-78230-BP rev 2.0 Wistron SoC: MV78230 A0 running 2 CPUs Custom configuration CPU: Marvell PJ4B (584) v7 (Rev 2) LE CPU # 0 CPU @ 1333Mhz, L2 @ 667Mhz DDR @ 667Mhz, TClock @ 250Mhz DDR 32Bit Width, FastPath Memory Access DDR ECC Disabled PEX 0.0(0): Root Complex Interface, Detected Link X4, GEN 1.1 PEX 1.0(1): Root Complex Interface, Detected Link X1, GEN 2.0 DRAM: 512 MB CS 0: base 0x00000000 size 512 MB Addresses 14M - 0M are saved for the U-Boot usage. NAND: 1024 MiB Bad block table found at page 524224, version 0x01 Bad block table found at page 524160, version 0x01 nand_read_bbt: Bad block at 0x000009c20000 nand_read_bbt: Bad block at 0x00000f060000 nand_read_bbt: Bad block at 0x000014a20000 nand_read_bbt: Bad block at 0x000017840000 nand_read_bbt: Bad block at 0x00001e540000 nand_read_bbt: Bad block at 0x00002f4c0000 FPU initialized to Run Fast Mode. USB 0: Host Mode USB 1: Host Mode USB 2: Device Mode Modules Detected: MMC: MRVL_MMC: 0 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Marvell>> printenv; ide reset; ext2load ide 2:1 0x0040000 uImage; ext2load ide 2:1 0x2000000 uInitrd; setenv bootargs $console $mtdparts root=/dev/sda2 rw rootdelay=10 baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 boardtest=1 console=console=ttyS0,115200 mtdids=nand0=armada-nand CASset=min sata_delay_reset=0 MALLOC_len=5 ethprime=egiga0 bootargs_root=root=/dev/ram rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage bootcmd=nand read 0x40000 $kernel_start $kernel_size; tftpboot 0x2000000 $ramdisk_name;setenv bootargs $console $mtdparts $bootargs_root ramdisk_size=$ramdisk_size_f ramdisk_blocksize=1024 ip=$bootargs_end $mvNetConfig;bootm 0x40000 0x2000000; loadpath=initrd.img ramdisk_size=4194304 ramdisk_size_f=12582912 ramdisk_name=initrd.img uver=v2.3.2.6 mfgmodel=IX4-300D autoload=yes ubin=0301 env_off=0xe0000 env1_off=0x100000 kernel_start=0x120000 initrd_start=0x520000 kernel_size=0x400000 initrd_size=0x400000 mtdparts=mtdparts=armada-nand:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; ethaddr=00:50:43:44:2a:32 eth1addr=00:50:43:2a:2a:32 eth2addr=00:50:43:2a:44:32 eth3addr=00:50:43:2a:44:2a mv_pon_addr=00:50:43:32:44:2a ethmtu=1500 eth1mtu=1500 eth2mtu=1500 eth3mtu=1500 mvNetConfig=mv_net_config=2,(00:50:43:11:11:11,0:1),mtu=1500 usb0Mode=host usb1Mode=host usb2Mode=device usbActive=0 yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=yes rcvrip=169.254.100.100 loadaddr=0x02000000 eeeEnable=no lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaClockGating=no enaWrAllo=no pexMode=RC disL2Cache=yes MPmode=SMP cacheShare=no setL2CacheWT=no disL2Prefetch=yes enaICPref=yes enaDCPref=yes enaFPU=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no amp_enable=no serverip=192.168.1.100 ipaddr=192.168.1.2 bootdelay=7 disaMvPnp=no enaAutoRecovery=yes pcieTune=no ethact=egiga0 Environment size: 2000/131067 bytes Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found Found adapter at bus 0, device 1 ... Scanning channels Device 2 @ 1 0: Model: ST31000528AS Firm: CC49 Ser#: 5VP3QJ9P Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Loading file "uImage" from ide device 2:1 (hdc1) 5064159 bytes read Loading file "uInitrd" from ide device 2:1 (hdc1) 22213824 bytes read Marvell>> bootm 0x40000 0x2000000 ## Booting kernel from Legacy Image at 00040000 ... Image Name: kernel 5.10.0-18-armmp-lpae Created: 2022-10-06 22:45:25 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5064095 Bytes = 4.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: ramdisk 5.10.0-18-armmp-lpae Created: 2022-10-06 22:45:25 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 22213760 Bytes = 21.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.0-18-armmp-lpae (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Debian 5.10.140-1 (2022-09-02) [ 0.000000] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Lenovo Iomega ix4-300d [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x000000001f000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s54796 r8192 d23028 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=armada-nand:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) root=/dev/sda2 rw rootdelay=10 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 460444K/524288K available (12288K kernel code, 1674K rwdata, 3216K rodata, 2048K init, 340K bss, 47460K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 37789 entries in 111 pages [ 0.000000] ftrace: allocated 111 pages with 6 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x1a696b10 -> 0x1a696b12 [ 0.000000] Aurora cache controller enabled, 16 ways, 1024 kB [ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000006] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.000019] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.001315] Console: colour dummy device 80x30 [ 0.001357] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.001372] pid_max: default: 32768 minimum: 301 [ 0.001898] LSM: Security Framework initializing [ 0.001999] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.002221] AppArmor: AppArmor initialized [ 0.002234] TOMOYO Linux initialized [ 0.002382] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002395] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003562] CPU: Testing write buffer coherency: ok [ 0.003886] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004883] Setting up static identity map for 0x400000 - 0x4000ac [ 0.005196] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x1 [ 0.005291] mvebu-pmsu: Initializing Power Management Service Unit [ 0.005450] rcu: Hierarchical SRCU implementation. [ 0.006888] EFI services will not be available. [ 0.007207] smp: Bringing up secondary CPUs ... [ 0.007821] Booting CPU 1 [ 0.008272] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012363] smp: Brought up 1 node, 2 CPUs [ 0.012378] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.012385] CPU: All CPU(s) started in SVC mode. [ 0.013061] devtmpfs: initialized [ 0.017681] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.017931] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.017962] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.018917] pinctrl core: initialized pinctrl subsystem [ 0.019703] DMI not present or invalid. [ 0.020416] NET: Registered protocol family 16 [ 0.022644] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.023424] audit: initializing netlink subsys (disabled) [ 0.024287] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1 [ 0.024593] thermal_sys: Registered thermal governor 'fair_share' [ 0.024600] thermal_sys: Registered thermal governor 'bang_bang' [ 0.024609] thermal_sys: Registered thermal governor 'step_wise' [ 0.024617] thermal_sys: Registered thermal governor 'user_space' [ 0.024624] thermal_sys: Registered thermal governor 'power_allocator' [ 0.024946] No ATAGs? [ 0.024984] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 [ 0.024993] hw-breakpoint: CPU 0 failed to disable vector catch [ 0.025030] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 [ 0.025916] Serial: AMBA PL011 UART driver [ 0.047031] Kprobes globally optimized [ 0.047599] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 1.509575] iommu: Default domain type: Translated [ 1.510079] vgaarb: loaded [ 1.510713] mc: Linux media interface: v0.10 [ 1.510770] videodev: Linux video capture interface: v2.00 [ 1.512091] NetLabel: Initializing [ 1.512103] NetLabel: domain hash size = 128 [ 1.512109] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 1.512212] NetLabel: unlabeled traffic allowed by default [ 1.512562] clocksource: Switched to clocksource armada_370_xp_clocksource [ 1.587191] VFS: Disk quotas dquot_6.6.0 [ 1.587308] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.588142] AppArmor: AppArmor Filesystem Enabled [ 1.598225] NET: Registered protocol family 2 [ 1.598374] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.599512] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.599642] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.599704] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.599740] TCP: Hash tables configured (established 4096 bind 4096) [ 1.599855] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.599880] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.600080] NET: Registered protocol family 1 [ 1.600109] NET: Registered protocol family 44 [ 1.600123] PCI: CLS 0 bytes, default 64 [ 1.600510] Trying to unpack rootfs image as initramfs... [ 2.554193] Freeing initrd memory: 21696K [ 2.554911] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.556430] Initialise system trusted keyrings [ 2.556531] Key type blacklist registered [ 2.556798] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 2.563984] zbud: loaded [ 2.565009] integrity: Platform Keyring initialized [ 2.565027] Key type asymmetric registered [ 2.565036] Asymmetric key parser 'x509' registered [ 2.565073] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 2.565251] io scheduler mq-deadline registered [ 2.570772] armada-xp-pinctrl d0018000.pin-ctrl: registered pinctrl driver [ 2.574103] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: [ 2.574145] mvebu-pcie soc:pcie@82000000: MEM 0x00d0040000..0x00d0041fff -> 0x0000040000 [ 2.574173] mvebu-pcie soc:pcie@82000000: MEM 0x00d0044000..0x00d0045fff -> 0x0000044000 [ 2.574199] mvebu-pcie soc:pcie@82000000: MEM 0x00d0048000..0x00d0049fff -> 0x0000048000 [ 2.574225] mvebu-pcie soc:pcie@82000000: MEM 0x00d004c000..0x00d004dfff -> 0x000004c000 [ 2.574250] mvebu-pcie soc:pcie@82000000: MEM 0x00d0080000..0x00d0081fff -> 0x0000080000 [ 2.574275] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 2.574299] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 2.574322] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 2.574345] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 2.574368] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 2.574391] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 2.574414] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 2.574437] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 2.574460] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 2.574477] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 2.574775] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 [ 2.574791] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.574804] pci_bus 0000:00: root bus resource [mem 0xd0040000-0xd0041fff] (bus address [0x00040000-0x00041fff]) [ 2.574816] pci_bus 0000:00: root bus resource [mem 0xd0044000-0xd0045fff] (bus address [0x00044000-0x00045fff]) [ 2.574827] pci_bus 0000:00: root bus resource [mem 0xd0048000-0xd0049fff] (bus address [0x00048000-0x00049fff]) [ 2.574838] pci_bus 0000:00: root bus resource [mem 0xd004c000-0xd004dfff] (bus address [0x0004c000-0x0004dfff]) [ 2.574849] pci_bus 0000:00: root bus resource [mem 0xd0080000-0xd0081fff] (bus address [0x00080000-0x00081fff]) [ 2.574858] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 2.574868] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 2.574969] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400 [ 2.575513] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400 [ 2.576713] PCI: bus0: Fast back to back transfers disabled [ 2.576729] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.576744] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.576884] pci 0000:01:00.0: [11ab:7042] type 00 class 0x010000 [ 2.576918] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x400fffff 64bit] [ 2.576936] pci 0000:01:00.0: reg 0x18: [io 0xf1100000-0xf11000ff] [ 2.577229] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 2.578208] PCI: bus1: Fast back to back transfers disabled [ 2.578222] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.578366] pci 0000:02:00.0: [1033:0194] type 00 class 0x0c0330 [ 2.578399] pci 0000:02:00.0: reg 0x10: [mem 0x4a000000-0x4a001fff 64bit] [ 2.578532] pci 0000:02:00.0: PME# supported from D0 D3hot [ 2.589589] PCI: bus2: Fast back to back transfers disabled [ 2.589605] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.589667] pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff] [ 2.589684] pci 0000:00:05.0: BAR 8: assigned [mem 0xf8100000-0xf81fffff] [ 2.589695] pci 0000:00:01.0: BAR 7: assigned [io 0x10000-0x10fff] [ 2.589713] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf80fffff 64bit] [ 2.589733] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x100ff] [ 2.589746] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.589757] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 2.589770] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 2.589788] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf8101fff 64bit] [ 2.589806] pci 0000:00:05.0: PCI bridge to [bus 02] [ 2.589817] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff] [ 2.589895] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 2.589988] pcieport 0000:00:05.0: enabling device (0140 -> 0142) [ 2.593434] mv_xor d0060900.xor: Marvell shared XOR driver [ 2.625764] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 2.626141] mv_xor d00f0900.xor: Marvell shared XOR driver [ 2.657757] mv_xor d00f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 2.660300] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.662693] printk: console [ttyS0] disabled [ 2.682869] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 28, base_baud = 15625000) is a 16550A [ 3.846755] printk: console [ttyS0] enabled [ 3.851967] Serial: AMBA driver [ 3.856127] STM32 USART driver initialized [ 3.863777] mousedev: PS/2 mouse device common for all mice [ 3.870731] rtc-mv d0010300.rtc: registered as rtc0 [ 3.875682] rtc-mv d0010300.rtc: setting system clock to 2022-10-10T12:44:50 UTC (1665405890) [ 3.989585] ledtrig-cpu: registered to indicate activity on CPUs [ 3.997081] NET: Registered protocol family 10 [ 4.044245] Segment Routing with IPv6 [ 4.048101] mip6: Mobile IPv6 [ 4.051132] NET: Registered protocol family 17 [ 4.055785] mpls_gso: MPLS GSO support [ 4.059696] ThumbEE CPU extension supported. [ 4.064047] Registering SWP/SWPB emulation handler [ 4.069058] registered taskstats version 1 [ 4.073200] Loading compiled-in X.509 certificates [ 4.415780] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 4.424668] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 4.435013] zswap: loaded using pool lzo/zbud [ 4.440045] Key type ._fscrypt registered [ 4.444127] Key type .fscrypt registered [ 4.448085] Key type fscrypt-provisioning registered [ 4.453358] AppArmor: AppArmor sha1 policy hashing enabled [ 4.463480] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.478614] Freeing unused kernel memory: 2048K [ 4.485147] Checked W+X mappings: passed, no W+X pages found [ 4.490858] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 5.022416] i2c_mv64xxx: module verification failed: signature and/or required key missing - tainting kernel [ 5.044776] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable. [ 5.062172] rtc-pcf8563 0-0051: registered as rtc1 [ 5.121111] mvneta d0070000.ethernet eth0: Using random mac address 7e:11:68:2f:22:c5 [ 5.155774] mvneta d0074000.ethernet eth1: Using random mac address 36:00:74:11:3b:cf [ 5.163536] SCSI subsystem initialized [ 5.189798] usbcore: registered new interface driver usbfs [ 5.229935] usbcore: registered new interface driver hub [ 5.250822] usbcore: registered new device driver usb [ 5.265741] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.297430] ehci-orion: EHCI orion driver [ 5.317893] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 5.328426] orion-ehci d0050000.usb: EHCI Host Controller [ 5.333935] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1 [ 5.342390] sata_mv 0000:01:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx [ 5.344000] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 2 [ 5.377364] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004 [ 5.411758] orion-ehci d0050000.usb: irq 34, io mem 0xd0050000 [ 5.428355] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 5.436746] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.444030] usb usb1: Product: xHCI Host Controller [ 5.448942] usb usb1: Manufacturer: Linux 5.10.0-18-armmp-lpae xhci-hcd [ 5.455593] usb usb1: SerialNumber: 0000:02:00.0 [ 5.456590] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00 [ 5.499431] hub 1-0:1.0: USB hub found [ 5.509324] hub 1-0:1.0: 2 ports detected [ 5.519473] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 5.519606] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 5.533056] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.540328] usb usb2: Product: EHCI Host Controller [ 5.540850] scsi host0: sata_mv [ 5.545233] usb usb2: Manufacturer: Linux 5.10.0-18-armmp-lpae ehci_hcd [ 5.545238] usb usb2: SerialNumber: d0050000.usb [ 5.550436] hub 2-0:1.0: USB hub found [ 5.556459] scsi host1: sata_mv [ 5.560738] hub 2-0:1.0: 1 port detected [ 5.568921] scsi host2: sata_mv [ 5.574389] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3 [ 5.574602] orion-ehci d0051000.usb: EHCI Host Controller [ 5.581912] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed [ 5.589026] orion-ehci d0051000.usb: new USB bus registered, assigned bus number 4 [ 5.593813] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.609539] scsi host3: sata_mv [ 5.613635] ata1: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8022000 irq 55 [ 5.621360] ata2: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8024000 irq 55 [ 5.629069] ata3: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8026000 irq 55 [ 5.636769] ata4: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8028000 irq 55 [ 5.644694] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 5.653027] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.660301] usb usb3: Product: xHCI Host Controller [ 5.665211] usb usb3: Manufacturer: Linux 5.10.0-18-armmp-lpae xhci-hcd [ 5.671867] usb usb3: SerialNumber: 0000:02:00.0 [ 5.676891] orion-ehci d0051000.usb: irq 35, io mem 0xd0051000 [ 5.677227] hub 3-0:1.0: USB hub found [ 5.686608] hub 3-0:1.0: 2 ports detected [ 5.696594] orion-ehci d0051000.usb: USB 2.0 started, EHCI 1.00 [ 5.702857] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 5.711188] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.718451] usb usb4: Product: EHCI Host Controller [ 5.723364] usb usb4: Manufacturer: Linux 5.10.0-18-armmp-lpae ehci_hcd [ 5.730011] usb usb4: SerialNumber: d0051000.usb [ 5.736414] hub 4-0:1.0: USB hub found [ 5.740237] hub 4-0:1.0: 1 port detected [ 6.116615] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 6.149219] ata1.00: ATA-8: ST31000528AS, CC49, max UDMA/133 [ 6.154917] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 6.185322] ata1.00: configured for UDMA/133 [ 6.190070] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC49 PQ: 0 ANSI: 5 [ 6.515114] ata2: SATA link down (SStatus 0 SControl 300) [ 6.835107] ata3: SATA link down (SStatus 0 SControl 300) [ 7.155141] ata4: SATA link down (SStatus 0 SControl 300) [ 7.277937] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 7.285808] sd 0:0:0:0: [sda] Write Protect is off [ 7.290738] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.395079] sda: sda1 sda2 sda3 < sda5 > [ 7.413240] sd 0:0:0:0: [sda] Attached SCSI disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext4 (1) -- /dev/sda2] fsck.ext4 -a -C0 /dev/sda2 rootfs: clean, 29667/60989440 files, 4313733/243943168 blocks done. [ 18.687325] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 19.056644] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 19.932389] systemd[1]: Inserted module 'autofs4' [ 20.135892] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 20.159636] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 20.265998] systemd[1]: Set hostname to <debian>. [ 21.559077] systemd[1]: Queued start job for default target Graphical Interface. [ 21.567989] random: systemd: uninitialized urandom read (16 bytes read) [ 21.578456] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 21.600754] random: systemd: uninitialized urandom read (16 bytes read) [ 21.608862] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 21.628729] random: systemd: uninitialized urandom read (16 bytes read) [ 21.636917] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 21.662075] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. [ 21.685969] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 21.709035] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 21.732980] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 21.757639] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ OK ] Set up automount Arbitrary…s File System Automount Point. [ 21.785036] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 21.809047] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 21.828841] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 21.848805] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 21.869616] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 21.889234] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 21.912995] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 21.937638] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 21.961312] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 21.985392] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 22.005880] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 22.029293] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 22.053095] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 22.077071] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 22.105089] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 22.129635] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 22.154218] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 22.185421] systemd[1]: Starting Load Kernel Module configfs... [ 22.190606] random: crng init done [ 22.194809] random: 23 urandom warning(s) missed due to ratelimiting Starting Load Kernel Module configfs... [ 22.221390] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 22.245469] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 22.280929] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 22.292130] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 22.311658] systemd[1]: Starting Journal Service... Starting Journal Service... [ 22.363775] fuse: init (API version 7.32) [ 22.368646] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 22.429347] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 22.461248] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 22.481553] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.501107] systemd[1]: Mounted Huge Pages File System. [ OK ] Mounted Huge Pages File System. [ 22.521403] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 22.545358] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 22.577381] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 22.608211] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 22.642494] systemd[1]: modprobe@configfs.service: Succeeded. [ 22.654439] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 22.686337] systemd[1]: modprobe@drm.service: Succeeded. [ 22.698400] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 22.730317] systemd[1]: modprobe@fuse.service: Succeeded. [ 22.742243] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 22.777331] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Creat[ 22.960681] systemd-journald[187]: Received client request to flush runtime journal. e System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Coldplug All udev Devices. Starting Helper to synchronize boot up for ifupdown... [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Started Rule-based Manager for Device Events and Files. [ 24.833592] debugfs: Directory 'cpu1' with parent 'opp' already present! [ OK 25.131289] adt7475 0-002e: ADT7473 device, revision 0 0m] Found device[ 25.137415] adt7475 0-002e: Optional features: fan4 pwm2 /dev/ttyS0. [ 25.171110] at24 0-0050: supply vcc not found, using dummy regulator [ 25.288154] orion_wdt: Initial timeout 171 sec [ 25.326348] at24 0-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write [ 25.378326] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xd3 [ 25.384787] nand: Samsung NAND 1GiB 3,3V 8-bit [ 25.389302] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 25.397021] marvell-nfc d00d0000.nand-controller: No minimum ECC strength, using 1b/512B [ 25.444664] Bad block table found at page 524224, version 0x01 [ 25.467276] Bad block table found at page 524160, version 0x01 [ 25.488805] nand_read_bbt: bad block at 0x00000f060000 [ 25.494084] nand_read_bbt: bad block at 0x000014a20000 [ 25.496934] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 25.499276] nand_read_bbt: bad block at 0x000017840000 [ 25.509753] nand_read_bbt: bad block at 0x00001e540000 [ 25.514939] nand_read_bbt: bad block at 0x00002f4c0000 [ 25.789171] 6 fixed-partitions partitions found on MTD device pxa3xx_nand-0 [ 25.808599] Creating 6 MTD partitions on "pxa3xx_nand-0": [ 25.868401] 0x000000000000-0x0000000e0000 : "u-boot" [ 25.885932] 0x0000000e0000-0x000000100000 : "u-boot-env" [ 25.905098] 0x000000100000-0x000000120000 : "u-boot-env2" [ 25.911118] 0x000000120000-0x000000520000 : "zImage" [ 25.922459] 0x000000520000-0x000000920000 : "initrd" [ 25.953118] 0x000000e00000-0x000040000000 : "boot" [ 26.220709] marvell-cesa d0090000.crypto: CESA device successfully registered [ OK ] Found device ST31000528AS 1. [ OK ] Found device ST31000528AS 5. [ OK ] Found device /sys/subsystem/net/devices/eth0. Activating swap /dev/disk/…9235-4a48-b782-c8a8e7525ed3... Starting File System Check…f349-4925-b5dd-e7503c027702... [ OK ] Started File System Check Daemon to report status. [ 26.492673] Adding 488444k swap on /dev/sda5. Priority:-2 extents:1 across:488444k FS [ OK ] Activated swap /dev/disk/b…a-9235-4a48-b782-c8a8e7525ed3. [ OK ] Reached target Swap. [ OK ] Finished File System Check…c-f349-4925-b5dd-e7503c027702. Mounting /boot...disks (100.0% complete) [ 27.852956] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 27.973087] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null) [ 27.980209] ext2 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff) [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. Starting Load AppArmor profiles... Starting Create Volatile Files and Directories... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ 28.753552] audit: type=1400 audit(1665405915.376:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=285 comm="apparmor_parser" [ OK ] Finished 28.770303] audit: type=1400 audit(1665405915.376:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=285 comm="apparmor_parser" ;1;39mUpdate UTMP about System B[ 28.788605] audit: type=1400 audit(1665405915.376:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=285 comm="apparmor_parser" oot/Shutdown. [ 28.810612] audit: type=1400 audit(1665405915.376:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=286 comm="apparmor_parser" [ 28.836591] audit: type=1400 audit(1665405915.456:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=287 comm="apparmor_parser" [ OK 28.854294] audit: type=1400 audit(1665405915.456:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=287 comm="apparmor_parser" 0m] Finished Load AppArmor profiles. [ OK ] Started ifup for eth0. Starting Raise network interfaces... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting System Logging Service... Starting User Login Management... [ OK ] Finished Raise network interfaces. [ OK ] Reached target Network. Starting OpenBSD Secure Shell server... Starting Permit User Sessions... Starting Rotate log files... [ 29.662516] mvneta d0070000.ethernet eth0: PHY [d0072004.mdio-mii:00] driver [Marvell 88E1318S] (irq=POLL) Startin[ 29.677858] mvneta d0070000.ethernet eth0: configuring for phy/rgmii-id link mode g Daily man-db regeneration... [ OK ] Started System Logging Service. [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started User Login Management. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Finished Rotate log files. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. [ OK ] Finished Daily man-db regeneration. [ 34.684557] hrtimer: interrupt took 12002920 ns Debian GNU/Linux 11 debian ttyS0 debian login:
Re: Mainline Debian on Iomega ix4-300d October 11, 2022 04:08AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Mainline Debian on Iomega ix4-300d October 11, 2022 06:22AM |
Registered: 1 year ago Posts: 6 |
root@debian:/mnt/usb# cat /proc/mtd dev: size erasesize name mtd0: 000e0000 00020000 "u-boot" mtd1: 00020000 00020000 "u-boot-env" mtd2: 00020000 00020000 "u-boot-env2" mtd3: 00400000 00020000 "zImage" mtd4: 00400000 00020000 "initrd" mtd5: 3f200000 00020000 "boot"
root@debian:/mnt/usb/tools# nandwrite /dev/mtd0 mtd0.img nandwrite: error!: /dev/mtd0 error 13 (Permission denied)
Re: Mainline Debian on Iomega ix4-300d October 15, 2022 10:08PM |
Admin Registered: 13 years ago Posts: 18,821 |
setenv mtdparts mtdparts=pxa3xx_nand-0:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash)
Re: Mainline Debian on Iomega ix4-300d October 16, 2022 06:03PM |
Registered: 1 year ago Posts: 6 |
BootROM 1.15 Booting from NAND flash DDR3 Training Sequence - Ver 2.3.4 DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER 2.3.2.6 ** U-Boot 2009.08 (Mar 04 2013 - 11:13:04) Marvell version: 2.3.2 PQ U-Boot Addressing: Code: 00600000:006BFFF0 BSS: 00708EC0 Stack: 0x5fff70 PageTable: 0x8e0000 Heap address: 0x900000:0xe00000 Board: DB-78230-BP rev 2.0 Wistron SoC: MV78230 A0 running 2 CPUs Custom configuration CPU: Marvell PJ4B (584) v7 (Rev 2) LE CPU # 0 CPU @ 1333Mhz, L2 @ 667Mhz DDR @ 667Mhz, TClock @ 250Mhz DDR 32Bit Width, FastPath Memory Access DDR ECC Disabled PEX 0.0(0): Root Complex Interface, Detected Link X4, GEN 1.1 PEX 1.0(1): Root Complex Interface, Detected Link X1, GEN 2.0 DRAM: 512 MB CS 0: base 0x00000000 size 512 MB Addresses 14M - 0M are saved for the U-Boot usage. NAND: 1024 MiB Bad block table found at page 524224, version 0x01 Bad block table found at page 524160, version 0x01 nand_read_bbt: Bad block at 0x000009c20000 nand_read_bbt: Bad block at 0x00000f060000 nand_read_bbt: Bad block at 0x000014a20000 nand_read_bbt: Bad block at 0x000017840000 nand_read_bbt: Bad block at 0x00001e540000 nand_read_bbt: Bad block at 0x00002f4c0000 FPU initialized to Run Fast Mode. USB 0: Host Mode USB 1: Host Mode USB 2: Device Mode Modules Detected: MMC: MRVL_MMC: 0 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x120000, size 0x400000 4194304 bytes read: OK NAND read: device 0 offset 0x520000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00040000 ... Image Name: Linux-3.2.40 Created: 2017-10-13 11:23:49 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3656384 Bytes = 3.5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: Created: 2017-10-13 12:07:49 UTC Image Type: ARM Linux RAMDisk Image (bzip2 compressed) Data Size: 3026568 Bytes = 2.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel.
Re: Mainline Debian on Iomega ix4-300d October 18, 2022 05:52AM |
Admin Registered: 13 years ago Posts: 18,821 |
ACBIAS
Re: Mainline Debian on Iomega ix4-300d October 25, 2022 04:10AM |
Re: Mainline Debian on Iomega ix4-300d December 17, 2022 03:50PM |
Registered: 1 year ago Posts: 4 |
cat dts/armada-xp-lenovo-ix4-300d.dtb >> zImage.fdtto use the correct device tree information. Nevertheless it doesn't boot... Thanks for suggesting to backup the old files which allowed me to recover my box in a matter of a few minutes.
BootROM 1.15 Booting from NAND flash DDR3 Training Sequence - Ver 2.3.4 DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER 2.3.2.6 ** U-Boot 2009.08 (Mar 04 2013 - 11:13:04) Marvell version: 2.3.2 PQ U-Boot Addressing: Code: 00600000:006BFFF0 BSS: 00708EC0 Stack: 0x5fff70 PageTable: 0x8e0000 Heap address: 0x900000:0xe00000 Board: DB-78230-BP rev 2.0 Wistron SoC: MV78230 A0 running 2 CPUs Custom configuration CPU: Marvell PJ4B (584) v7 (Rev 2) LE CPU # 0 CPU @ 1333Mhz, L2 @ 667Mhz DDR @ 667Mhz, TClock @ 250Mhz DDR 32Bit Width, FastPath Memory Access DDR ECC Disabled PEX 0.0(0): Root Complex Interface, Detected Link X4, GEN 1.1 PEX 1.0(1): Root Complex Interface, Detected Link X1, GEN 2.0 DRAM: 512 MB CS 0: base 0x00000000 size 512 MB Addresses 14M - 0M are saved for the U-Boot usage. NAND: 1024 MiB Bad block table found at page 524224, version 0x01 Bad block table found at page 524160, version 0x01 nand_read_bbt: Bad block at 0x000013480000 nand_read_bbt: Bad block at 0x00002d5e0000 FPU initialized to Run Fast Mode. USB 0: Host Mode USB 1: Host Mode USB 2: Device Mode Modules Detected: MMC: MRVL_MMC: 0 Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ console=console=ttyS0,115200 mtdids=nand0=armada-nand CASset=min sata_delay_reset=0 MALLOC_len=5 ethprime=egiga0 bootargs_root=root=/dev/ram rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage loadpath=initrd.img ramdisk_size=4194304 ramdisk_size_f=12582912 ramdisk_name=initrd.img uver=v2.3.2.6 mfgmodel=IX4-300D autoload=yes ubin=0301 env_off=0xe0000 env1_off=0x100000 kernel_start=0x120000 initrd_start=0x520000 kernel_size=0x400000 initrd_size=0x400000 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; eth2addr=00:50:43:00:00:02 eth3addr=00:50:43:02:00:00 mv_pon_addr=00:50:43:02:00:00 ethmtu=1500 eth1mtu=1500 eth2mtu=1500 eth3mtu=1500 mvNetConfig=mv_net_config=2,(00:50:43:11:11:11,0:1),mtu=1500 usb0Mode=host usb1Mode=host usb2Mode=device usbActive=0 yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=yes rcvrip=169.254.100.100 loadaddr=0x02000000 eeeEnable=no lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 fileaddr=2000000 netmask=255.255.255.0 ipaddr=192.168.1.2 serverip=192.168.1.100 serial_number=5565U01001G429003E9J0M1 opid=Z14036848 ethaddr=00:D0:B8:2A:3D:DF serialNo=SM10G088614300039E eth1addr=00:D0:B8:2A:3D:E0 modelname=SM10G08861 serialno=0,01e9Zo+jlOoI1bqH1SMijWS3wc9+Z6OT0g+2ARgC0kWb+pTHVJoA4oNiUB1hc3WXLu,SM10G088614300039E, mfgtest_state=final_tested_ok runintime=14400 ftp_serverip=192.168.32.4 ftp_log_user=runinlog ftp_log_password=123 ftp_log_dir=storagelogs/soclogs/partlogs/IX4-300D/runin ftp_pass_user=qrypass ftp_pass_password=123 ftp_pass_dir=socquery ftp_qry_user=qrypass ftp_qry_password=123 ftp_qry_dir=socquery bootdelay=3 ethact=egiga0 filesize=554B4D bootargs=console=ttyS0,115200 mtdparts=armada-nand:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boow archboot=usb reset;fatload usb 0:1 $loadaddr uImage; setenv bootargs $console $mtdparts root=PARTUUID=c1ab722d-ebdc-4865-9c88-f918db507eb5 rw; bootm $loadaddr; mtdparts=mtdparts=pxa3xx_nand-0:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(f) bootdebian=printenv; ide reset; ext2load ide 2:1 0x0040000 uImage; ext2load ide 2:1 0x2000000 uInitrd; setenv bootargs $console $mtdparts root=LABEL=rootfs rw rootdelay=10; bootm 0x40000 0x; bootcmd=run bootdebian; stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaClockGating=no enaWrAllo=no pexMode=RC disL2Cache=yes MPmode=SMP cacheShare=no setL2CacheWT=no disL2Prefetch=yes enaICPref=yes enaDCPref=yes enaFPU=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no amp_enable=no disaMvPnp=no enaAutoRecovery=yes pcieTune=no Environment size: 2924/131067 bytes Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found Found adapter at bus 0, device 1 ... Scanning channels Device 2 @ 1 0: Model: Samsung SSD 850 EVO 250GB Firm: EMT02B6Q Ser#: S21PNXAGA45154K Type: Hard Disk Supports 48-bit addressing Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Device 3 @ 1 1: Model: WDC WD20EARX-00MMMB0 Firm: 80.00A80 Ser#: WD-WMAWZ0424224 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 4 @ 1 2: Model: WDC WD40EFPX-68C6CN0 Firm: 81.00A81 Ser#: WD-WX72A922CRR4 Type: Hard Disk Supports 48-bit addressing Capacity: 1718295.8 MB = 1678.0 GB (-775897424 x 512) Device 5 @ 1 3: Model: WDC WD40EFPX-68C6CN0 Firm: 81.00A81 Ser#: WD-WX72A922CVFK Type: Hard Disk Supports 48-bit addressing Capacity: 1718295.8 MB = 1678.0 GB (-775897424 x 512) Loading file "uImage" from ide device 2:1 (hdc1) 5240863 bytes read Loading file "uInitrd" from ide device 2:1 (hdc1) 10861122 bytes read ## Booting kernel from Legacy Image at 00040000 ... Image Name: Linux-6.0.7-mvebu-tld-1 Created: 2022-12-17 21:05:59 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5240799 Bytes = 5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: initramfs-6.0.7-mvebu-tld-1 Created: 2022-12-17 21:06:06 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 10861058 Bytes = 10.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... data abort pc : [<0117de7c>] lr : [<0117b83c>] sp : 0167bb40 ip : 0000001c fp : 0167625c r10: 0117a610 r9 : 0117b088 r8 : 01676260 r7 : 00000bdc r6 : 0167a750 r5 : 00000055 r4 : 0118117e r3 : 00000bdc r2 : fed12000 r1 : f1012000 r0 : 00000055 Flags: nzCv IRQs off FIQs off Mode SVC_32 Resetting CPU ...