codingdave
Ramdisk failed for WD MyCloud Mirror when installed but works over TFTP June 23, 2022 03:18PM |
INITRD: 0x00f00000+0x00390000 overlaps in-use memory region - disabling initrd
List of all partitions: 0100 4096 ram0 (driver?) 0101 4096 ram1 (driver?) 0102 4096 ram2 (driver?) 0103 4096 ram3 (driver?) 0104 4096 ram4 (driver?) 0105 4096 ram5 (driver?) 0106 4096 ram6 (driver?) 0107 4096 ram7 (driver?) 0800 4883770584 sda driver: sd 0801 498688 sda1 54b1600b-498d-40af-828c-49030ec6f629 0802 3500032 sda2 7333fdc9-4438-4017-b51f-ce8f175f1f08 0803 4879770624 sda3 0e1236ad-8a07-4df3-a5eb-702f33b7830f 0810 4883770584 sdb driver: sd 0811 498688 sdb1 27b8a519-317d-46e6-806f-e7413dcd6a64 0812 3500032 sdb2 3d7d9664-ca0d-410e-aa1e-8c77b91aca37 0813 4879770624 sdb3 cb2f41b1-567b-4003-8076-b8f3ff1ec059 No filesystem could mount root, tried: ext3 ext2 ext4 vfat msdos iso9660 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) ]---
BootROM 1.08 Booting from NAND flash High speed PHY - Version: 2.1.2 (COM-PHY-V20) Update PEX Device ID 0x67100 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver 4.5.0 DDR3 Training Sequence - Ended Successfully Status = MV_OK BootROM: Image checksum verification PASSED ** LOADER ** U-Boot 2011.12 (Dec 24 2013 - 20:21:45) Marvell version: v2011.12 2013_Q1.2 (ALPHA U-BOOT : 1.0) Board: RD-88F6710_ALpha_KingsCanyon SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB Map: Code: 0x1fef5000:0x1ff9faac BSS: 0x1ffef784 Stack: 0x1f9f4ef8 Heap: 0x1f9f5000:0x1fef5000 NAND: flash id : daad 256 MiB MMC: MRVL_MMC: 0 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: Bad block at 0x00000e7c0000 PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0 PEX 0.1(1): Detected No Link. FPU not initialized USB 0: Host Mode USB 1: Host Mode Modules/Interfaces Detected: RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Not Marvell PHY id1 ffff id2 ffff Enable HD1 Enable HD2 Net: egiga1 Warning: egiga1 MAC addresses don't match: Address in SROM is 00:50:43:02:00:00 Address in environment is 00:50:43:02:02:00 Hit any key to stop autoboot: 0 Marvell>> dhcp && setenv serverip 192.168.178.34 && tftp 0x2000000 uImage && tftp 0x3000000 uRamdisk && bootm 0x2000000 0x3000000 BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 42 *** Unhandled DHCP Option in OFFER/ACK: 158 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 42 *** Unhandled DHCP Option in OFFER/ACK: 158 DHCP client bound to address 192.168.178.69 Using egiga1 device TFTP from server 192.168.178.34; our IP address is 192.168.178.69 Filename 'uImage'. Load address: 0x2000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ############################## done Bytes transferred = 4253881 (40e8b9 hex) Using egiga1 device TFTP from server 192.168.178.34; our IP address is 192.168.178.69 Filename 'uRamdisk'. Load address: 0x3000000 Loading: ################################################################# ################################################################# ################################################################# ############################################################ done Bytes transferred = 3733371 (38f77b hex) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: linux-rolling-stable Created: 2022-06-22 15:20:01 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4253817 Bytes = 4.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: Initial Ramdisk (gz) Created: 2022-06-23 13:39:10 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 3733307 Bytes = 3.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... DTB:0x00412E30 (0x00003A49) C:0x000080E0-0x00416920->0x00D7B900-0x0118A140 DTB:0x01186650 (0x00003AD2) Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.18.5+ (david@tower) (arm-linux-gnueabihf-gcc (GCC) 12.1.0, GNU ld (GNU Binutils) 2.38) #1 SMP Wed Jun 22 12:46:37 CEST 2022 CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache OF: fdt: Machine model: WD MyCloud Mirror Memory policy: Data cache writeback Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] CPU: All CPU(s) started in SVC mode. percpu: Embedded 11 pages/cpu s14036 r8192 d22828 u45056 Built 1 zonelists, mobility grouping on. Total pages: 129920 Kernel command line: root=/dev/ram console=ttyS0,115200 max_loop=32 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 502376K/524288K available (8778K kernel code, 491K rwdata, 2072K rodata, 1024K init, 334K bss, 21912K reserved, 0K cma-reserved, 0K highmem) rcu: Hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 L2C: DT/platform modifies aux control register: 0x12086302 -> 0x1a086302 Aurora cache controller enabled, 4 ways, 256 kB Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 Switching to timer-based delay loop, resolution 53ns sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114532461029ns clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101933890472 ns Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 37.50 BogoMIPS (lpj=187500) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket -1, mpidr 0 Setting up static identity map for 0x100000 - 0x100060 mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 mvebu-pmsu: Initializing Power Management Service Unit rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... smp: Brought up 1 node, 1 CPU SMP: Total of 1 processors activated (37.50 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: 2, 16384 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered PF_NETLINK/PF_ROUTE protocol family DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' cpuidle: using governor ladder cryptd: max_cpu_qlen set to 1000 raid6: int32x8 gen() 366 MB/s raid6: int32x4 gen() 424 MB/s raid6: int32x2 gen() 536 MB/s raid6: int32x1 gen() 479 MB/s raid6: using algorithm int32x2 gen() 536 MB/s raid6: .... xor() 222 MB/s, rmw enabled raid6: using intx1 recovery algorithm SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered clocksource: Switched to clocksource armada_370_xp_clocksource VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) FS-Cache: Loaded CacheFiles: Loaded NET: Registered PF_INET protocol family IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Initialise system trusted keyrings Trying to unpack rootfs image as initramfs... workingset: timestamp_bits=14 max_order=17 bucket_order=3 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Key type cifs.idmap registered xor: measuring software checksum speed arm4regs : 1151 MB/sec 8regs : 1047 MB/sec 32regs : 1067 MB/sec xor: using function: arm4regs (1151 MB/sec) async_tx: api initialized (async) Key type asymmetric registered Asymmetric key parser 'x509' registered Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler kyber registered armada-370-pinctrl f1018000.pin-ctrl: registered pinctrl driver mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: mvebu-pcie soc:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 mvebu-pcie soc:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000 mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 mvebu-pcie soc:pcie@82000000: pcie0.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@1,0 does not contain intx interrupt mvebu-pcie soc:pcie@82000000: pcie1.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@2,0 does not contain intx interrupt mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff]) pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400 pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400 PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:01:00.0: [1912:0015] type 00 class 0x0c0330 pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x40001fff 64bit] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold PCI: bus1: Fast back to back transfers disabled pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 PCI: bus2: Fast back to back transfers enabled pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8001fff 64bit] pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] pci 0000:00:02.0: PCI bridge to [bus 02] pci 0000:00:01.0: enabling device (0140 -> 0142) mv_xor f1060800.xor: Marvell shared XOR driver Freeing initrd memory: 3648K mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled printk: console [ttyS0] disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 12500000) is a 16550A printk: console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 29, base_baud = 12500000) is a 16550A brd: module loaded loop: module loaded sata_mv f10a0000.sata: slots 32 ports 2 scsi host0: sata_mv scsi host1: sata_mv ata1: SATA max UDMA/133 irq 38 ata2: SATA max UDMA/133 irq 38 hwmon hwmon0: temp1_input not attached to any thermal zone mvneta f1074000.ethernet eth0: Using hardware mac address 00:50:43:02:02:00 usbcore: registered new interface driver lan78xx ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1050000.usb: EHCI Host Controller orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1050000.usb: irq 35, io mem 0xf1050000 orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 5.18.5+ ehci_hcd usb usb1: SerialNumber: f1050000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected orion-ehci f1051000.usb: EHCI Host Controller orion-ehci f1051000.usb: new USB bus registered, assigned bus number 2 orion-ehci f1051000.usb: irq 36, io mem 0xf1051000 orion-ehci f1051000.usb: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 5.18.5+ ehci_hcd usb usb2: SerialNumber: f1051000.usb hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver ohci-platform: OHCI generic platform driver uhci_hcd: USB Universal Host Controller Interface driver xhci_hcd 0000:01:00.0: failed to load firmware renesas_usb_fw.mem, fallback to ROM xhci_hcd 0000:01:00.0: xHCI Host Controller xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 xhci_hcd 0000:01:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x0000001100000090 xhci_hcd 0000:01:00.0: xHCI Host Controller xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 4 xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 5.18.5+ xhci-hcd usb usb3: SerialNumber: 0000:01:00.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.18 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 5.18.5+ xhci-hcd usb usb4: SerialNumber: 0000:01:00.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected fotg210_hcd: FOTG210 Host Controller (EHCI) Driver Warning! fotg210_hcd should always be loaded before uhci_hcd and ohci_hcd, not after SPI driver max3421-hcd has no spi_device_id for maxim,max3421 usbcore: registered new interface driver usb-storage ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata1.00: ATA-9: WDC WD50EFRX-68MYMN1, 82.00A82, max UDMA/133 ata1.00: 9767541168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD50EFRX-68M 0A82 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 9767541168 512-byte logical blocks: (5.00 TB/4.55 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata2.00: ATA-9: WDC WD50EFRX-68MYMN1, 82.00A82, max UDMA/133 ata2.00: 9767541168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD50EFRX-68M 0A82 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 9767541168 512-byte logical blocks: (5.00 TB/4.55 TiB) sd 1:0:0:0: [sdb] 4096-byte physical blocks sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: [sdb] Attached SCSI disk rtc-mv f1010300.rtc: internal RTC not ticking i2c_dev: i2c /dev entries driver mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs marvell-cesa f1090000.crypto: CESA device successfully registered hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered PF_INET6 protocol family Segment Routing with IPv6 In-situ OAM (IOAM) with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered PF_PACKET protocol family Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates armada-370-pinctrl f1018000.pin-ctrl: unsupported function gpio on pin mpp54 pinctrl core: failed to register map default (0): invalid type given input: gpio-keys as /devices/platform/gpio-keys/input/input0 Freeing unused kernel image (initmem) memory: 1024K Run /init as init process # Loading, please wait... # Mounting filesystems... # Check disk and init ### Press any key to stop and run shell... (2)block device autoloading is deprecated and will be removed. md: md2 stopped. md/raid1:md2: active with 2 out of 2 mirrors md2: detected capacity change from 0 to 9759279104 mdadm: /dev/md/2 has been started with 2 drives. block device autoloading is deprecated and will be removed. md: md1 stopped. md/raid1:md1: active with 2 out of 2 mirrors md1: detected capacity change from 0 to 6995968 mdadm: /dev/md/1 has been started with 2 drives. block device autoloading is deprecated and will be removed. md: md0 stopped. md/raid1:md0: active with 2 out of 2 mirrors md0: detected capacity change from 0 to 996736 mdadm: /dev/md/0 has been started with 2 drives. EXT4-fs (md1): mounted filesystem with ordered data mode. Quota mode: none. # Switch to real OS... ### Press any key to stop and run shell... (2)systemd[1]: System time before build time, advancing clock. systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 10 (buster)! systemd[1]: Set hostname to <wdmc>. systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) systemd[1]: /lib/systemd/system/rpc-statd.service:13: PIDFile= references path below legacy directory /var/run/, updating /var/run/rpc.statd.pid → /run/rpc.statd.pid; please update the unit file accordingly. random: crng init done systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Created slice User and Session Slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on Journal Socket. Mounting NFSD configuration filesystem... Mounting RPC Pipe File System... Starting Create list of re…odes for the current kernel... [ OK ] Created slice system-getty.slice. [ OK ] Listening on fsck to fsckd communication Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on udev Control Socket. [ OK ] Reached target Local Encrypted Volumes. Starting Nameserver information manager... [ OK ] Reached target Slices. Starting Load Kernel Modules... [ OK ] Listening on udev Kernel Socket. Mounting Kernel Debug File System... Starting Journal Service... Starting udev Coldplug all Devices... Starting Remount Root and Kernel File Systems... [ OK ] Mounted NFSD configuration filesystem. [ OK ] Mounted RPC Pipe File System. [ OK ] Started Create list of req… nodes for the current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Mounted Kernel Debug File System. [ OK ] Started Nameserver information manager. Starting Apply Kernel Variables... Starting pNFS block layout mapping daemon... EXT4-fs (md1): re-mounted. Quota mode: none. systemd[1]: Started Remount Root and Kernel File Systems. [ OK ] Started Remount Root and Kernel File Systems. systemd[1]: Started pNFS block layout mapping daemon. [ OK ] Started pNFS block layout mapping daemon. systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... systemd[1]: Starting Create System Users... Starting Create System Users... systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. systemd[1]: Started Apply Kernel Variables. [ OK ] Started Apply Kernel Variables. systemd[1]: Started Load/Save Random Seed. [ OK ] Started Load/Save Random Seed. systemd[1]: Started Create System Users. [ OK ] Started Create System Users. systemd[1]: Starting Create Static Device Nodes in /dev... Starting Create Static Device Nodes in /dev... systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Starting Flush Journal to Persistent Storage... systemd-journald[1044]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Kernel Device Manager. sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 [ OK ] Found device /dev/ttyS0. [ OK ] Started udev Coldplug all Devices. [ OK ] Found device /dev/md0. [ OK ] Found device /dev/md2. Starting File System Check on /dev/md2... Activating swap /dev/md0... [ OK ] Started MD array monitor. Adding 498364k swap on /dev/md0. Priority:-2 extents:1 across:498364k Starting Helper to synchronize boot up for ifupdown... [ OK ] Activated swap /dev/md0. [ OK ] Started Helper to synchronize boot up for ifupdown. [ OK ] Started File System Check Daemon to report status. [ OK ] Reached target Swap. Mounting /tmp... [ OK ] Mounted /tmp. [ OK ] Started File System Check on /dev/md2.e) Mounting /home... EXT4-fs (md2): mounted filesystem with ordered data mode. Quota mode: none. [ OK ] Mounted /home. [ OK ] Reached target Local File Systems. Starting Preprocess NFS configuration... Starting Raise network interfaces... Starting Create Volatile Files and Directories... [ OK ] Started Preprocess NFS configuration. Starting NFSv4 ID-name mapping service... [ OK ] Reached target NFS client services. [ OK ] Started NFSv4 ID-name mapping service. [ OK ] Started Create Volatile Files and Directories. Starting RPC bind portmap service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started RPC bind portmap service. [ OK ] Reached target RPC Port Mapper. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Modem Manager... Starting Resets System Activity Data Collector... [ OK ] Started Self Monitoring an…ing Technology (SMART) Daemon. Starting Initialize hardware monitoring sensors... Starting System Logging Service... [ OK ] Started D-Bus System Message Bus. Starting WPA supplicant... Starting Network Manager... Starting Login Service... Starting Restore /etc/reso… the ppp link was shut down... [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started System Logging Service. [ OK ] Started Resets System Activity Data Collector. [ OK ] Started Restore /etc/resol…re the ppp link was shut down. [ OK ] Started Initialize hardware monitoring sensors. [ OK ] Started WPA supplicant. [ OK ] Started Login Service. [ OK ] Started Raise network interfaces. Starting Authorization Manager... [ OK ] Started Authorization Manager. [ OK ] Started Network Manager. Starting Network Manager Wait Online... [ OK ] Reached target Network. Starting OpenBSD Secure Shell server... Starting NFS Mount Daemon... Starting Hostname Service... [ OK ] Started Modem Manager. [ OK ] Started NFS Mount Daemon. Starting NFS server and services... [ OK ] Started Hostname Service. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Stopped NFS server and services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Permit User Sessions... [ OK ] Started Regular background program processing daemon. Stopping NFSv4 ID-name mapping service... Stopping NFS Mount Daemon... Starting Network Manager Script Dispatcher Service... [ OK ] Stopped NFSv4 ID-name mapping service. [ OK ] Stopped NFS Mount Daemon. [ OK ] Started Permit User Sessions. [ OK ] Started Network Manager Script Dispatcher Service. mvneta f1074000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL) mvneta f1074000.ethernet eth0: configuring for phy/rgmii-id link mode mvneta f1074000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Started Network Manager Wait Online. [ OK ] Reached target Network is Online. Starting LSB: exim Mail Transport Agent... Starting /etc/rc.local Compatibility... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: exim Mail Transport Agent. [ OK ] Reached target Multi-User System. Starting watchdog daemon... [ OK ] Started watchdog daemon. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Debian GNU/Linux 10 wdmc ttyS0 wdmc login: root Password: Last login: Thu Jun 23 13:05:20 UTC 2022 on ttyS0 Linux wdmc 5.18.5+ #1 SMP Wed Jun 22 12:46:37 CEST 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@wdmc:~# poweroff root@wdmc:~# [ OK ] Stopped target RPC Port Mapper. Stopping pNFS block layout mapping daemon... [ OK ] Stopped target Timers. [ OK ] Stopped Daily apt upgrade and clean activities. [ OK ] Stopped Daily rotation of log files. [ OK ] Stopped topping Session c1 of user root. Stopping Authorization Manager... [ OK ] Stopped Daily Cleanup of Temporary Directories. [ OK ] Stopped target Graphical Interface. Stopping watchdog daemon... [ OK ] Stopped Daily man-db regeneration. [ OK ] Stopped pNFS block layout mapping daemon. [ OK ] Stopped Authorization Manager. [ OK ] Stopped Serial Getty on ttyS0. [ OK ] Stopped Session c1 of user root. [ OK ] Stopped watchdog daemon. [ OK ] Stopped target Multi-User System. [ OK ] Stopped Initialize hardware monitoring sensors. Stopping System Logging Service... Stopping LSB: exim Mail Transport Agent... Stopping Regular background program processing daemon... Stopping OpenBSD Secure Shell server... [ OK ] Stopped Resets System Activity Data Collector. Stopping Modem Manager... Stopping Self Monitoring a…g Technology (SMART) Daemon... Stopping Login Service... Stopping User Manager for UID 0... [ OK ] Stopped target Login Prompts. Stopping Getty on tty1... [ OK ] Removed slice system-serial\x2dgetty.slice. Unmounting RPC Pipe File System... [ OK ] Stopped Modem Manager. [ OK ] Stopped Self Monitoring an…ing Technology (SMART) Daemon. [ OK ] Stopped System Logging Service. [ OK ] Stopped OpenBSD Secure Shell server. [ OK ] Stopped Regular background program processing daemon. [ OK ] Stopped Getty on tty1. [ OK ] Stopped User Manager for UID 0. [ OK ] Unmounted RPC Pipe File System. [ OK ] Stopped Login Service. [ OK ] Stopped LSB: exim Mail Transport Agent. [ OK ] Stopped target System Time Synchronized. Stopping User Runtime Directory /run/user/0... [ OK ] Stopped /etc/rc.local Compatibility. [ OK ] Stopped target Network is Online. [ OK ] Stopped Network Manager Wait Online. [ OK ] Removed slice system-getty.slice. [ OK ] Unmounted /run/user/0. [ OK ] Stopped User Runtime Directory /run/user/0. [ OK ] Removed slice User Slice of UID 0. Stopping Permit User Sessions... [ OK ] Stopped Permit User Sessions. [ OK ] Stopped target Remote File Systems. [ OK ] Stopped target Remote File Systems (Pre). [ OK ] Stopped target NFS client services. [ OK ] Stopped target Network. Stopping Network Manager... Stopping Raise network interfaces... Stopping WPA supplicant... [ OK ] Stopped WPA supplicant. [ OK ] Stopped Raise network interfaces. [ OK ] Stopped Network Manager. Stopping D-Bus System Message Bus... [ OK ] Stopped D-Bus System Message Bus. [ OK ] Stopped target Basic System. [ OK ] Stopped target Sockets. [ OK ] Closed Syslog Socket. [ OK ] Stopped target Slices. [ OK ] Removed slice User and Session Slice. [ OK ] Stopped target Paths. [ OK ] Closed D-Bus System Message Bus Socket. [ OK ] Stopped target System Initialization. Stopping Update UTMP about System Boot/Shutdown... Stopping Network Time Synchronization... [ OK ] Stopped target Local Encrypted Volumes. [ OK ] Stopped Dispatch Password …ts to Console Directory Watch. [ OK ] Stopped Forward Password R…uests to Wall Directory Watch. [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped Load Kernel Modules. Stopping Load/Save Random Seed... [ OK ] Stopped Network Time Synchronization. [ OK ] Stopped Update UTMP about System Boot/Shutdown. [ OK ] Stopped Load/Save Random Seed. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Stopped target Local File Systems. Unmounting /home... Unmounting /tmp... [ OK ] Unmounted /tmp. [ OK ] Stopped target Swap. Deactivating swap /dev/dis…833f-45e9-a244-4de96f617b84... [ OK ] Deactivated swap /dev/disk/by-id/md-name-_none_:0. [ OK ] Deactivated swap /dev/disk/by-label/Swap. [ OK ] Deactivated swap /dev/disk…0-833f-45e9-a244-4de96f617b84. [ OK ] Deactivated swap /dev/md/0. [ OK ] Deactivated swap /dev/disk…fb:971c6894:dce50791:79a6b62d. [ OK ] Deactivated swap /dev/md0. [ OK ] Unmounted /home. [ OK ] Stopped File System Check on /dev/md2. [ OK ] Stopped target Local File Systems (Pre). [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Create System Users. [ OK ] Stopped Remount Root and Kernel File Systems. [ OK ] Removed slice system-systemd\x2dfsck.slice. [ OK ] Reached target Shutdown. [ OK ] Reached target Unmount All Filesystems. [ OK ] Reached target Final Step. [ OK ] Started Power-Off. [ OK ] Reached target Power-Off. printk: systemd-shutdow: 39 output lines suppressed due to ratelimiting systemd-shutdown[1]: Syncing filesystems and block devices. systemd-shutdown[1]: Sending SIGTERM to remaining processes... systemd-journald[1044]: Received SIGTERM from PID 1 (systemd-shutdow). systemd-shutdown[1]: Sending SIGKILL to remaining processes... systemd-shutdown[1]: Unmounting file systems. [2754]: Remounting '/' read-only in with options '(null)'. EXT4-fs (md1): re-mounted. Quota mode: none. systemd-shutdown[1]: All filesystems unmounted. systemd-shutdown[1]: Deactivating swaps. systemd-shutdown[1]: All swaps deactivated. systemd-shutdown[1]: Detaching loop devices. systemd-shutdown[1]: All loop devices detached. systemd-shutdown[1]: Detaching DM devices. sd 1:0:0:0: [sdb] Synchronizing SCSI cache sd 1:0:0:0: [sdb] Stopping disk sd 0:0:0:0: [sda] Synchronizing SCSI cache sd 0:0:0:0: [sda] Stopping disk reboot: System halted
BootROM 1.08 Booting from NAND flash High speed PHY - Version: 2.1.2 (COM-PHY-V20) Update PEX Device ID 0x67100 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver 4.5.0 DDR3 Training Sequence - Ended Successfully Status = MV_OK BootROM: Image checksum verification PASSED ** LOADER ** U-Boot 2011.12 (Dec 24 2013 - 20:21:45) Marvell version: v2011.12 2013_Q1.2 (ALPHA U-BOOT : 1.0) Board: RD-88F6710_ALpha_KingsCanyon SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB Map: Code: 0x1fef5000:0x1ff9faac BSS: 0x1ffef784 Stack: 0x1f9f4ef8 Heap: 0x1f9f5000:0x1fef5000 NAND: flash id : daad 256 MiB MMC: MRVL_MMC: 0 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: Bad block at 0x00000e7c0000 PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0 PEX 0.1(1): Detected No Link. FPU not initialized USB 0: Host Mode USB 1: Host Mode Modules/Interfaces Detected: RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Not Marvell PHY id1 ffff id2 ffff Enable HD1 Enable HD2 Net: egiga1 Warning: egiga1 MAC addresses don't match: Address in SROM is 00:50:43:02:00:00 Address in environment is 00:50:43:02:02:00 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x500000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: linux-rolling-stable Created: 2022-06-22 15:20:01 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4253817 Bytes = 4.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Initial Ramdisk (gz) Created: 2022-06-23 13:39:10 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 3733307 Bytes = 3.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... DTB:0x00412E30 (0x00003A49) C:0x000080E0-0x00416920->0x00D7B900-0x0118A140 DTB:0x01186650 (0x00003AD2) Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.18.5+ (david@tower) (arm-linux-gnueabihf-gcc (GCC) 12.1.0, GNU ld (GNU Binutils) 2.38) #1 SMP Wed Jun 22 12:46:37 CEST 2022 CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache OF: fdt: Machine model: WD MyCloud Mirror Memory policy: Data cache writeback INITRD: 0x00f00000+0x00390000 overlaps in-use memory region - disabling initrd Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] CPU: All CPU(s) started in SVC mode. percpu: Embedded 11 pages/cpu s14036 r8192 d22828 u45056 Built 1 zonelists, mobility grouping on. Total pages: 129920 Kernel command line: root=/dev/ram console=ttyS0,115200 max_loop=32 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 506024K/524288K available (8778K kernel code, 491K rwdata, 2072K rodata, 1024K init, 334K bss, 18264K reserved, 0K cma-reserved, 0K highmem) rcu: Hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 L2C: DT/platform modifies aux control register: 0x12086302 -> 0x1a086302 Aurora cache controller enabled, 4 ways, 256 kB Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 Switching to timer-based delay loop, resolution 53ns sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114532461029ns clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101933890472 ns Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 37.50 BogoMIPS (lpj=187500) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket -1, mpidr 0 Setting up static identity map for 0x100000 - 0x100060 mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 mvebu-pmsu: Initializing Power Management Service Unit rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... smp: Brought up 1 node, 1 CPU SMP: Total of 1 processors activated (37.50 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: 2, 16384 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered PF_NETLINK/PF_ROUTE protocol family DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' cpuidle: using governor ladder cryptd: max_cpu_qlen set to 1000 raid6: int32x8 gen() 366 MB/s raid6: int32x4 gen() 424 MB/s raid6: int32x2 gen() 536 MB/s raid6: int32x1 gen() 479 MB/s raid6: using algorithm int32x2 gen() 536 MB/s raid6: .... xor() 222 MB/s, rmw enabled raid6: using intx1 recovery algorithm SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered clocksource: Switched to clocksource armada_370_xp_clocksource VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) FS-Cache: Loaded CacheFiles: Loaded NET: Registered PF_INET protocol family IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Initialise system trusted keyrings workingset: timestamp_bits=14 max_order=17 bucket_order=3 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Key type cifs.idmap registered xor: measuring software checksum speed arm4regs : 1151 MB/sec 8regs : 1056 MB/sec 32regs : 1068 MB/sec xor: using function: arm4regs (1151 MB/sec) async_tx: api initialized (async) Key type asymmetric registered Asymmetric key parser 'x509' registered Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler kyber registered armada-370-pinctrl f1018000.pin-ctrl: registered pinctrl driver mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: mvebu-pcie soc:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 mvebu-pcie soc:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000 mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 mvebu-pcie soc:pcie@82000000: pcie0.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@1,0 does not contain intx interrupt mvebu-pcie soc:pcie@82000000: pcie1.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@2,0 does not contain intx interrupt mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff]) pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400 pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400 PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:01:00.0: [1912:0015] type 00 class 0x0c0330 pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x40001fff 64bit] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold PCI: bus1: Fast back to back transfers disabled pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 PCI: bus2: Fast back to back transfers enabled pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8001fff 64bit] pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] pci 0000:00:02.0: PCI bridge to [bus 02] pci 0000:00:01.0: enabling device (0140 -> 0142) mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled printk: console [ttyS0] disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 12500000) is a 16550A printk: console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 29, base_baud = 12500000) is a 16550A brd: module loaded loop: module loaded sata_mv f10a0000.sata: slots 32 ports 2 scsi host0: sata_mv scsi host1: sata_mv ata1: SATA max UDMA/133 irq 38 ata2: SATA max UDMA/133 irq 38 hwmon hwmon0: temp1_input not attached to any thermal zone mvneta f1074000.ethernet eth0: Using random mac address 02:2d:92:a9:28:39 usbcore: registered new interface driver lan78xx ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1050000.usb: EHCI Host Controller orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1050000.usb: irq 35, io mem 0xf1050000 orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 5.18.5+ ehci_hcd usb usb1: SerialNumber: f1050000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected orion-ehci f1051000.usb: EHCI Host Controller orion-ehci f1051000.usb: new USB bus registered, assigned bus number 2 orion-ehci f1051000.usb: irq 36, io mem 0xf1051000 orion-ehci f1051000.usb: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 5.18.5+ ehci_hcd usb usb2: SerialNumber: f1051000.usb hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver ohci-platform: OHCI generic platform driver uhci_hcd: USB Universal Host Controller Interface driver xhci_hcd 0000:01:00.0: failed to load firmware renesas_usb_fw.mem, fallback to ROM xhci_hcd 0000:01:00.0: xHCI Host Controller xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 xhci_hcd 0000:01:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x0000001100000090 xhci_hcd 0000:01:00.0: xHCI Host Controller xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 4 xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 5.18.5+ xhci-hcd usb usb3: SerialNumber: 0000:01:00.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.18 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 5.18.5+ xhci-hcd usb usb4: SerialNumber: 0000:01:00.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected fotg210_hcd: FOTG210 Host Controller (EHCI) Driver Warning! fotg210_hcd should always be loaded before uhci_hcd and ohci_hcd, not after SPI driver max3421-hcd has no spi_device_id for maxim,max3421 usbcore: registered new interface driver usb-storage ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata1.00: ATA-9: WDC WD50EFRX-68MYMN1, 82.00A82, max UDMA/133 ata1.00: 9767541168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD50EFRX-68M 0A82 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 9767541168 512-byte logical blocks: (5.00 TB/4.55 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk rtc-mv f1010300.rtc: internal RTC not ticking i2c_dev: i2c /dev entries driver mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs marvell-cesa f1090000.crypto: CESA device successfully registered hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered PF_INET6 protocol family Segment Routing with IPv6 In-situ OAM (IOAM) with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered PF_PACKET protocol family Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates armada-370-pinctrl f1018000.pin-ctrl: unsupported function gpio on pin mpp54 pinctrl core: failed to register map default (0): invalid type given ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata2.00: ATA-9: WDC WD50EFRX-68MYMN1, 82.00A82, max UDMA/133 ata2.00: 9767541168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD50EFRX-68M 0A82 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 9767541168 512-byte logical blocks: (5.00 TB/4.55 TiB) sd 1:0:0:0: [sdb] 4096-byte physical blocks sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: [sdb] Attached SCSI disk input: gpio-keys as /devices/platform/gpio-keys/input/input0 md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: invalid raid superblock magic on sda1 md: sda1 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sda2 md: sda2 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sda3 md: sda3 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sdb1 md: sdb1 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sdb2 md: sdb2 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sdb3 md: sdb3 does not have a valid v0.90 superblock, not importing! md: autorun ... md: ... autorun DONE. List of all partitions: 0100 4096 ram0 (driver?) 0101 4096 ram1 (driver?) 0102 4096 ram2 (driver?) 0103 4096 ram3 (driver?) 0104 4096 ram4 (driver?) 0105 4096 ram5 (driver?) 0106 4096 ram6 (driver?) 0107 4096 ram7 (driver?) 0800 4883770584 sda driver: sd 0801 498688 sda1 54b1600b-498d-40af-828c-49030ec6f629 0802 3500032 sda2 7333fdc9-4438-4017-b51f-ce8f175f1f08 0803 4879770624 sda3 0e1236ad-8a07-4df3-a5eb-702f33b7830f 0810 4883770584 sdb driver: sd 0811 498688 sdb1 27b8a519-317d-46e6-806f-e7413dcd6a64 0812 3500032 sdb2 3d7d9664-ca0d-410e-aa1e-8c77b91aca37 0813 4879770624 sdb3 cb2f41b1-567b-4003-8076-b8f3ff1ec059 No filesystem could mount root, tried: ext3 ext2 ext4 vfat msdos iso9660 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) ]---
codingdave
Re: Ramdisk failed for WD MyCloud Mirror when installed but works over TFTP June 23, 2022 03:50PM |
Marvell>> printenv CASset=min MALLOC_len=5 autoload=no baudrate=115200 bootargs=root=/dev/ram console=ttyS0,115200 max_loop=32 bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootdelay=1 cacheShare=no console=console=ttyS0,115200 disL2Cache=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaFPU=no enaWrAllo=no eth1addr=00:50:43:02:00:00 eth1mtu=1500 ethact=egiga1 ethaddr=00:50:43:02:02:00 ethmtu=1500 ethprime=egiga0 image_name=uImage initrd_name=uInitrd ipaddr=2.66.66.200 loadaddr=0x02000000 loads_echo=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:4m(boot),-(rootfs) mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500 mv_pon_addr=00:50:43:00:00:02 nandEcc=1bit netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 rcvrip=169.254.100.100 rootpath=/srv/oneiric sata_delay_reset=0 sata_dma_mode=yes serverip=2.66.66.32 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=1 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81
cat root@wdmc:~# cat /proc/mtd dev: size erasesize name root@wdmc:~# dmesg | grep -i mtd root@wdmc:~# dmesg | grep -i nand root@wdmc:~# cat /proc/config.gz | grep -i nand # NAND # CONFIG_MTD_ONENAND is not set # CONFIG_MTD_RAW_NAND is not set # CONFIG_MTD_SPI_NAND is not set # CONFIG_MTD_NAND_ECC_SW_HAMMING is not set # CONFIG_MTD_NAND_ECC_SW_BCH is not set # CONFIG_MTD_NAND_ECC_MXIC is not set # end of NAND root@wdmc:~# uname -r 5.18.5+
Re: Ramdisk failed for WD MyCloud Mirror when installed but works over TFTP June 23, 2022 04:58PM |
Admin Registered: 13 years ago Posts: 18,594 |
> Marvell>> printenv > CASset=min > MALLOC_len=5 > autoload=no > baudrate=115200 > bootargs=root=/dev/ram console=ttyS0,115200 > max_loop=32 > bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none > bootargs_root=root=/dev/nfs rw > bootcmd=nand read.e 0xa00000 0x500000 > 0x500000;nand read.e 0xf00000 0xa00000 > 0x500000;bootm 0xa00000 0xf00000 >
setenv initrd_high 0xffffffff
codingdave
Re: Ramdisk failed for WD MyCloud Mirror when installed but works over TFTP June 23, 2022 05:20PM |
Marvell>> setenv initrd_high 0xffffffff Marvell>> nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000
BootROM 1.08 Booting from NAND flash High speed PHY - Version: 2.1.2 (COM-PHY-V20) Update PEX Device ID 0x67100 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver 4.5.0 DDR3 Training Sequence - Ended Successfully Status = MV_OK BootROM: Image checksum verification PASSED ** LOADER ** U-Boot 2011.12 (Dec 24 2013 - 20:21:45) Marvell version: v2011.12 2013_Q1.2 (ALPHA U-BOOT : 1.0) Board: RD-88F6710_ALpha_KingsCanyon SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB Map: Code: 0x1fef5000:0x1ff9faac BSS: 0x1ffef784 Stack: 0x1f9f4ef8 Heap: 0x1f9f5000:0x1fef5000 NAND: flash id : daad 256 MiB MMC: MRVL_MMC: 0 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: Bad block at 0x00000e7c0000 PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0 PEX 0.1(1): Detected No Link. FPU not initialized USB 0: Host Mode USB 1: Host Mode Modules/Interfaces Detected: RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Not Marvell PHY id1 ffff id2 ffff Enable HD1 Enable HD2 Net: egiga1 Warning: egiga1 MAC addresses don't match: Address in SROM is 00:50:43:02:00:00 Address in environment is 00:50:43:02:02:00 Hit any key to stop autoboot: 0 Marvell>> setenv initrd_high 0xffffffff Marvell>> nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 NAND read: device 0 offset 0x500000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: linux-rolling-stable Created: 2022-06-22 15:20:01 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4253817 Bytes = 4.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Initial Ramdisk (gz) Created: 2022-06-23 13:39:10 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 3733307 Bytes = 3.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... DTB:0x00412E30 (0x00003A49) C:0x000080E0-0x00416920->0x00D7B900-0x0118A140 DTB:0x01186650 (0x00003AD2) Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.18.5+ (david@tower) (arm-linux-gnueabihf-gcc (GCC) 12.1.0, GNU ld (GNU Binutils) 2.38) #1 SMP Wed Jun 22 12:46:37 CEST 2022 CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache OF: fdt: Machine model: WD MyCloud Mirror Memory policy: Data cache writeback INITRD: 0x00f00000+0x00390000 overlaps in-use memory region - disabling initrd Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] CPU: All CPU(s) started in SVC mode. percpu: Embedded 11 pages/cpu s14036 r8192 d22828 u45056 Built 1 zonelists, mobility grouping on. Total pages: 129920 Kernel command line: root=/dev/ram console=ttyS0,115200 max_loop=32 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 506024K/524288K available (8778K kernel code, 491K rwdata, 2072K rodata, 1024K init, 334K bss, 18264K reserved, 0K cma-reserved, 0K highmem) rcu: Hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 L2C: DT/platform modifies aux control register: 0x12086302 -> 0x1a086302 Aurora cache controller enabled, 4 ways, 256 kB Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 Switching to timer-based delay loop, resolution 53ns sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114532461029ns clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101933890472 ns Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 37.50 BogoMIPS (lpj=187500) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket -1, mpidr 0 Setting up static identity map for 0x100000 - 0x100060 mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 mvebu-pmsu: Initializing Power Management Service Unit rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... smp: Brought up 1 node, 1 CPU SMP: Total of 1 processors activated (37.50 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: 2, 16384 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered PF_NETLINK/PF_ROUTE protocol family DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' cpuidle: using governor ladder cryptd: max_cpu_qlen set to 1000 raid6: int32x8 gen() 366 MB/s raid6: int32x4 gen() 424 MB/s raid6: int32x2 gen() 536 MB/s raid6: int32x1 gen() 479 MB/s raid6: using algorithm int32x2 gen() 536 MB/s raid6: .... xor() 222 MB/s, rmw enabled raid6: using intx1 recovery algorithm SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered clocksource: Switched to clocksource armada_370_xp_clocksource VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) FS-Cache: Loaded CacheFiles: Loaded NET: Registered PF_INET protocol family IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Initialise system trusted keyrings workingset: timestamp_bits=14 max_order=17 bucket_order=3 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Key type cifs.idmap registered xor: measuring software checksum speed arm4regs : 1151 MB/sec 8regs : 1067 MB/sec 32regs : 1068 MB/sec xor: using function: arm4regs (1151 MB/sec) async_tx: api initialized (async) Key type asymmetric registered Asymmetric key parser 'x509' registered Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler kyber registered armada-370-pinctrl f1018000.pin-ctrl: registered pinctrl driver mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: mvebu-pcie soc:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 mvebu-pcie soc:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000 mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 mvebu-pcie soc:pcie@82000000: pcie0.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@1,0 does not contain intx interrupt mvebu-pcie soc:pcie@82000000: pcie1.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@2,0 does not contain intx interrupt mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff]) pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400 pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400 PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:01:00.0: [1912:0015] type 00 class 0x0c0330 pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x40001fff 64bit] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold PCI: bus1: Fast back to back transfers disabled pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 PCI: bus2: Fast back to back transfers enabled pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8001fff 64bit] pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] pci 0000:00:02.0: PCI bridge to [bus 02] pci 0000:00:01.0: enabling device (0140 -> 0142) mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled printk: console [ttyS0] disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 12500000) is a 16550A printk: console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 29, base_baud = 12500000) is a 16550A brd: module loaded loop: module loaded sata_mv f10a0000.sata: slots 32 ports 2 scsi host0: sata_mv scsi host1: sata_mv ata1: SATA max UDMA/133 irq 38 ata2: SATA max UDMA/133 irq 38 hwmon hwmon0: temp1_input not attached to any thermal zone mvneta f1074000.ethernet eth0: Using random mac address a6:36:51:d7:57:4e usbcore: registered new interface driver lan78xx ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1050000.usb: EHCI Host Controller orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1050000.usb: irq 35, io mem 0xf1050000 orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 5.18.5+ ehci_hcd usb usb1: SerialNumber: f1050000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected orion-ehci f1051000.usb: EHCI Host Controller orion-ehci f1051000.usb: new USB bus registered, assigned bus number 2 orion-ehci f1051000.usb: irq 36, io mem 0xf1051000 orion-ehci f1051000.usb: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 5.18.5+ ehci_hcd usb usb2: SerialNumber: f1051000.usb hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver ohci-platform: OHCI generic platform driver uhci_hcd: USB Universal Host Controller Interface driver xhci_hcd 0000:01:00.0: failed to load firmware renesas_usb_fw.mem, fallback to ROM xhci_hcd 0000:01:00.0: xHCI Host Controller xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 xhci_hcd 0000:01:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x0000001100000090 xhci_hcd 0000:01:00.0: xHCI Host Controller xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 4 xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 5.18.5+ xhci-hcd usb usb3: SerialNumber: 0000:01:00.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.18 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 5.18.5+ xhci-hcd usb usb4: SerialNumber: 0000:01:00.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected fotg210_hcd: FOTG210 Host Controller (EHCI) Driver Warning! fotg210_hcd should always be loaded before uhci_hcd and ohci_hcd, not after SPI driver max3421-hcd has no spi_device_id for maxim,max3421 usbcore: registered new interface driver usb-storage ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata1.00: ATA-9: WDC WD50EFRX-68MYMN1, 82.00A82, max UDMA/133 ata1.00: 9767541168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD50EFRX-68M 0A82 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 9767541168 512-byte logical blocks: (5.00 TB/4.55 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata2.00: ATA-9: WDC WD50EFRX-68MYMN1, 82.00A82, max UDMA/133 ata2.00: 9767541168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD50EFRX-68M 0A82 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 9767541168 512-byte logical blocks: (5.00 TB/4.55 TiB) sd 1:0:0:0: [sdb] 4096-byte physical blocks sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: [sdb] Attached SCSI disk rtc-mv f1010300.rtc: internal RTC not ticking i2c_dev: i2c /dev entries driver mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs marvell-cesa f1090000.crypto: CESA device successfully registered hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered PF_INET6 protocol family Segment Routing with IPv6 In-situ OAM (IOAM) with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered PF_PACKET protocol family Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates armada-370-pinctrl f1018000.pin-ctrl: unsupported function gpio on pin mpp54 pinctrl core: failed to register map default (0): invalid type given input: gpio-keys as /devices/platform/gpio-keys/input/input0 md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: invalid raid superblock magic on sda1 md: sda1 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sda2 md: sda2 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sda3 md: sda3 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sdb1 md: sdb1 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sdb2 md: sdb2 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sdb3 md: sdb3 does not have a valid v0.90 superblock, not importing! md: autorun ... md: ... autorun DONE. List of all partitions: 0100 4096 ram0 (driver?) 0101 4096 ram1 (driver?) 0102 4096 ram2 (driver?) 0103 4096 ram3 (driver?) 0104 4096 ram4 (driver?) 0105 4096 ram5 (driver?) 0106 4096 ram6 (driver?) 0107 4096 ram7 (driver?) 0800 4883770584 sda driver: sd 0801 498688 sda1 54b1600b-498d-40af-828c-49030ec6f629 0802 3500032 sda2 7333fdc9-4438-4017-b51f-ce8f175f1f08 0803 4879770624 sda3 0e1236ad-8a07-4df3-a5eb-702f33b7830f 0810 4883770584 sdb driver: sd 0811 498688 sdb1 27b8a519-317d-46e6-806f-e7413dcd6a64 0812 3500032 sdb2 3d7d9664-ca0d-410e-aa1e-8c77b91aca37 0813 4879770624 sdb3 cb2f41b1-567b-4003-8076-b8f3ff1ec059 No filesystem could mount root, tried: ext3 ext2 ext4 vfat msdos iso9660 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) ]---
Re: Ramdisk failed for WD MyCloud Mirror when installed but works over TFTP June 23, 2022 06:11PM |
Admin Registered: 13 years ago Posts: 18,594 |
setenv bootcmd 'nand read.e 0x02000000 0x500000 0x500000;nand read.e 0x03000000 0xa00000 0x500000;bootm 0x02000000 0x03000000'and then
boot
Re: Ramdisk failed for WD MyCloud Mirror when installed but works over TFTP June 24, 2022 02:23AM |
Registered: 1 year ago Posts: 1 |
Marvell>> setenv bootcmd 'nand read.e 0x02000000 0x500000 0x500000;nand read.e 0x03000000 0xa00000 0x500000;bootm 0x02000000 0x03000000' Marvell>> saveenv Saving Environment to NAND... Erasing Nand... Writing to Nand... done Marvell>> printenv CASset=min MALLOC_len=5 autoload=no baudrate=115200 bootargs=root=/dev/ram console=ttyS0,115200 max_loop=32 bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0x02000000 0x500000 0x500000;nand read.e 0x03000000 0xa00000 0x500000;bootm 0x02000000 0x03000000 bootdelay=1 cacheShare=no console=console=ttyS0,115200 disL2Cache=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaFPU=no enaWrAllo=no eth1addr=00:50:43:02:00:00 eth1mtu=1500 ethact=egiga1 ethaddr=00:50:43:02:02:00 ethmtu=1500 ethprime=egiga0 image_name=uImage initrd_name=uInitrd ipaddr=2.66.66.200 loadaddr=0x02000000 loads_echo=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:4m(boot),-(rootfs) mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500 mv_pon_addr=00:50:43:00:00:02 nandEcc=1bit netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 rcvrip=169.254.100.100 rootpath=/srv/oneiric sata_delay_reset=0 sata_dma_mode=yes serverip=2.66.66.32 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=1 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 1524/524284 bytes Marvell>> boot
Re: Ramdisk failed for WD MyCloud Mirror when installed but works over TFTP June 24, 2022 03:03AM |
Admin Registered: 13 years ago Posts: 18,594 |