Promise Apollo Cloud - Armada 385 December 05, 2022 04:52AM |
Registered: 1 year ago Posts: 7 |
Identifying UART Ports UART has 4 ports: TX(Transmit), RX(Receive), Vcc(Voltage), and GND(Ground). You might be able to find 4 ports with the TX and RX letters written in the PCB. But if there is no indication, you might need to try to find them yourself using a multimeter or a logic analyzer. With a multimeter and the device powered off: - To identify the GND pin use the Continuity Test mode, place the back lead into ground and test with the red one until you hear a sound from the multimeter. Several GND pins can be found the PCB, so you might have found or not the one belonging to UART. - To identify the VCC port, set the DC voltage mode and set it up to 20 V of voltage. Black probe on ground and red probe on the pin. Power on the device. If the multimeter measures a constant voltage of either 3.3 V or 5 V, you’ve found the Vcc pin. If you get other voltages, retry with other ports. - To identify the TX port, DC voltage mode up to 20 V of voltage, black probe on ground, and red probe on the pin, and power on the device. If you find the voltage fluctuates for a few seconds and then stabilizes at the Vcc value, you’ve most likely found the TX port. This is because when powering on, it sends some debug data. - The RX port would be the closest one to the other 3, it has the lowest voltage fluctuation and lowest overall value of all the UART pins. You can confuse the TX and RX ports and nothing would happen, but if you confuses the GND and the VCC port you might fry the circuit.
BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01 (Apr 03 2018 - 10:46:04) Marvell version: 2015_T1.0p5 Board: A38x-Customer-Board-0 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1066 [MHz] L2 @ 533 [MHz] TClock @ 250 [MHz] DDR @ 533 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB NAND: 128 MiB MMC: mv_sdh: 0 SF: Detected W25Q16 with page size 4 KiB, total 2 MiB USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x3fec0000:0x3ff95dc0 BSS: 0x3ffef7dc Stack: 0x3f9aff20 Heap: 0x3f9b0000:0x3fec0000 U-Boot Environment: 0x00100000:0x00110000 (SPI) Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | SGMII | 0x01 | egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 2 d 0 Reset SCSI AHCI init for unit0 SATA link 0 timeout. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Found 0 device(s). (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found USB1: Port (usbActive) : 0 Interface (usbType = 3) : Only one active controller supported! Skipping USB1 initialization. lowlevel init failed scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Creating 1 MTD partitions on "nand0": 0x000000000000-0x000008000000 : "mtd=0" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=0" UBI: MTD device size: 128 MiB UBI: number of good PEBs: 1016 UBI: number of bad PEBs: 8 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 12 UBI: total number of reserved PEBs: 1004 UBI: number of PEBs reserved for bad PEB handling: 10 UBI: max/mean erase counter: 3/1 UBI: mtd1 is detached from ubi0 Creating 1 MTD partitions on "nand0": 0x000000000000-0x000008000000 : "mtd=0" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=0" UBI: MTD device size: 128 MiB UBI: number of good PEBs: 1016 UBI: number of bad PEBs: 8 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 12 UBI: total number of reserved PEBs: 1004 UBI: number of PEBs reserved for bad PEB handling: 10 UBI: max/mean erase counter: 3/1 UBIFS: recovery needed UBIFS: recovery deferred UBIFS: mounted UBI device 0, volume 0, name "fw" UBIFS: mounted read-only UBIFS: file system size: 124309504 bytes (121396 KiB, 118 MiB, 979 LEBs) UBIFS: journal size: 6221824 bytes (6076 KiB, 5 MiB, 49 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 5182151 bytes (5060 KiB) Loading file '/boot/uImage' to addr 0x02000000 with size 3802456 (0x003a0558)... Done Loading file '/boot/device.dtb' to addr 0x01000000 with size 14977 (0x00003a81)... Done Loading file '/boot/initramfs.img' to addr 0x02500000 with size 33508338 (0x01ff4bf2)... Done bootargs=mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 ## Booting kernel from Legacy Image at 02000000 ... Image Name: Apollo Kernel Created: 2018-02-22 7:09:40 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3802392 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02500000 ... Image Name: ramdisk_0.01.0000.32 Created: 2016-03-21 11:01:43 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 33508274 Bytes = 32 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Only one active controller supported! Skipping USB1 stop. failed to stop USB controller 1 Loading Kernel Image ... OK OK Loading Device Tree to 00ff9000, end 00fffa80 ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.10.70-svn5196 (root@ApolloFW) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d188 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Marvell Armada 385 Reference Design [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @c0fa7000 s7424 r8192 d13056 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260594 [ 0.000000] Kernel command line: mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1024MB = 1024MB total [ 0.000000] Memory: 998936k/998936k available, 49640k reserved, 254976K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xfff00000 ( 247 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0700000 ( 775 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc06acc8c (6804 kB) [ 0.000000] .init : 0xc06ad000 - 0xc06e7d00 ( 236 kB) [ 0.000000] .data : 0xc06e8000 - 0xc073c320 ( 337 kB) [ 0.000000] .bss : 0xc073c320 - 0xc079a91c ( 378 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] [ 0.000000] LSP version: linux-3.10.70-2015_T1.1p7 [ 0.000000] [ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B [ 0.000000] Console: colour dummy device 80x30 [ 0.000575] Calibrating delay loop... 2125.00 BogoMIPS (lpj=10625024) [ 0.060046] pid_max: default: 32768 minimum: 301 [ 0.060123] Mount-cache hash table entries: 512 [ 0.060514] CPU: Testing write buffer coherency: ok [ 0.060643] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.060683] Setting up static identity map for 0xc0519218 - 0xc0519270 [ 0.060860] mvebu-pmsu: Initializing Power Management Service Unit [ 0.060903] Initializing CPU Reset module [ 1.060034] CPU1: failed to come online [ 1.060055] Brought up 1 CPUs [ 1.060061] SMP: Total of 1 processors activated (2125.00 BogoMIPS). [ 1.060065] CPU: All CPU(s) started in SVC mode. [ 1.060353] devtmpfs: initialized [ 1.063161] mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 [ 1.063335] pinctrl core: initialized pinctrl subsystem [ 1.063482] NET: Registered protocol family 16 [ 1.064052] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.066620] irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated [ 1.067085] irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated [ 1.079980] bio: create slab <bio-0> at 0 [ 1.080438] mvebu-pcie pcie-controller.3: PCIe0.0: link down [ 1.080464] mvebu-pcie pcie-controller.3: PCIe1.0: link down [ 1.080598] mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 [ 1.080608] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.080616] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.080624] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.080906] PCI: bus0: Fast back to back transfers disabled [ 1.080915] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.080923] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.081026] PCI: bus1: Fast back to back transfers enabled [ 1.081138] PCI: bus2: Fast back to back transfers enabled [ 1.081173] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.081183] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.081192] PCI: enabling device 0000:00:01.0 (0140 -> 0143) [ 1.081200] PCI: enabling device 0000:00:02.0 (0140 -> 0143) [ 1.081618] SCSI subsystem initialized [ 1.082152] usbcore: registered new interface driver usbfs [ 1.082225] usbcore: registered new interface driver hub [ 1.082313] usbcore: registered new device driver usb [ 1.082485] pps_core: LinuxPPS API ver. 1 registered [ 1.082490] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.082542] PTP clock support registered [ 1.083017] Switching to clocksource armada_370_xp_clocksource [ 1.089902] NET: Registered protocol family 2 [ 1.090367] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 1.090464] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.090562] TCP: Hash tables configured (established 8192 bind 8192) [ 1.090605] TCP: reno registered [ 1.090613] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.090639] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.090772] NET: Registered protocol family 1 [ 1.090953] RPC: Registered named UNIX socket transport module. [ 1.090959] RPC: Registered udp transport module. [ 1.090963] RPC: Registered tcp transport module. [ 1.090967] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.091073] Unpacking initramfs... [ 2.660067] Freeing initrd memory: 32716K (c2501000 - c44f4000) [ 2.661017] bounce pool size: 64 pages [ 2.661283] exFAT: Version 1.2.9 [ 2.661426] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.661507] NTFS driver 2.1.30 [Flags: R/O]. [ 2.661530] fuse init (API version 7.22) [ 2.661852] msgmni has been set to 1516 [ 2.662509] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 2.662516] io scheduler noop registered [ 2.662521] io scheduler deadline registered [ 2.662534] io scheduler cfq registered (default) [ 2.663238] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.663708] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.703488] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 2.733471] mv_xor f1060800.xor: freeing 1 in use descriptors! [ 2.733481] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 2.733623] mv_xor f1060900.xor: Marvell shared XOR driver [ 2.773485] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 2.803471] mv_xor f1060900.xor: freeing 1 in use descriptors! [ 2.803480] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 2.845063] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.866186] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A [ 3.516522] console [ttyS0] enabled [ 3.522797] loop: module loaded [ 3.526303] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.535127] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.544622] scsi0 : ahci_mv_platform [ 3.548423] scsi1 : ahci_mv_platform [ 3.552195] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 [ 3.560147] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 [ 3.569364] armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC [ 3.583750] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 3.595822] Bad block table found at page 65472, version 0x01 [ 3.601932] Bad block table found at page 65408, version 0x01 [ 3.609150] 1 cmdlinepart partitions found on MTD device armada-nand [ 3.615533] Creating 1 MTD partitions on "armada-nand": [ 3.620773] 0x000000000000-0x000008000000 : "fw" [ 3.627138] m25p80 spi0.0: w25q16 (2048 Kbytes) [ 3.631685] 3 cmdlinepart partitions found on MTD device spi0.0 [ 3.637635] Creating 3 MTD partitions on "spi0.0": [ 3.642439] 0x000000000000-0x000000100000 : "uboot" [ 3.647941] 0x000000100000-0x000000110000 : "env" [ 3.653237] 0x000000110000-0x000000200000 : "others" [ 3.659975] SoC: model = 0x6810, revision = 0x4 [ 3.664670] mvPncVirtBase = 0xf0c00000, pncTcamSize = 1024 [ 3.670167] o 2 Giga ports supported [ 3.673939] o NETA acceleration mode 4 [ 3.677869] o BM supported for CPU: 4 BM pools [ 3.682496] o PnC supported (Enabled) [ 3.686352] o RX Queue support: 8 Queues * 256 Descriptors [ 3.692023] o TX Queue support: 8 Queues * 532 Descriptors [ 3.697703] o GSO supported [ 3.700675] o GRO supported [ 3.703658] o Receive checksum offload supported [ 3.708459] o Transmit checksum offload supported [ 3.713356] o Driver ERROR statistics enabled [ 3.717895] o Driver INFO statistics enabled [ 3.722346] o Driver DEBUG statistics enabled [ 3.726893] [ 3.729491] port #0: is_sgmii=0, is_rgmii=1, phy_addr=0 [ 3.734787] o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 [ 3.743108] [ 3.744602] o Port 0 is connected to Linux netdevice [ 3.751741] o eth0, ifindex = 2, GbE port = 0 [ 3.759891] giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) [ 3.766006] [ 3.767625] port #1: is_sgmii=1, is_rgmii=0, phy_addr=1 [ 3.772867] o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048 [ 3.781189] [ 3.782683] o Port 1 is connected to Linux netdevice [ 3.789056] o eth1, ifindex = 3, GbE port = 1 [ 3.797207] giga p=1: mtu=1500, mac=ee:a6:f4:2f:c6:f0 (random) [ 3.803150] [ 3.805232] libphy: orion_mdio_bus: probed [ 3.810980] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.817544] ehci-pci: EHCI PCI platform driver [ 3.822086] ehci-orion: EHCI orion driver [ 3.826204] orion-ehci f1058000.usb: EHCI Host Controller [ 3.831631] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 3.839292] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 [ 3.863047] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 3.869349] hub 1-0:1.0: USB hub found [ 3.873129] hub 1-0:1.0: 1 port detected [ 3.877402] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.882736] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 3.890387] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 [ 3.896504] hub 2-0:1.0: USB hub found [ 3.900269] hub 2-0:1.0: 1 port detected [ 3.904289] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.909620] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 3.917198] ata2: SATA link down (SStatus 0 SControl 300) [ 3.922637] ata1: SATA link down (SStatus 0 SControl 300) [ 3.928510] hub 3-0:1.0: USB hub found [ 3.932277] hub 3-0:1.0: 1 port detected [ 3.936329] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.941662] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 3.949304] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 [ 3.955416] hub 4-0:1.0: USB hub found [ 3.959182] hub 4-0:1.0: 1 port detected [ 3.963198] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.968530] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 3.976398] hub 5-0:1.0: USB hub found [ 3.980163] hub 5-0:1.0: 1 port detected [ 3.984421] usbcore: registered new interface driver usb-storage [ 3.990941] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 3.998250] i2c /dev entries driver [ 4.012506] armada_thermal f10e4078.thermal: Overheat threshold between 92..107 [ 4.020415] orion_wdt: Initial timeout 171 sec [ 4.024955] cpuidle: using governor ladder [ 4.029144] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 [ 4.038486] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) [ 4.047018] mvCesaInit: channels=2, session=640, queue=256 [ 4.066147] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode [ 4.075237] cesadev_init(c06c6c88) [ 4.079005] usbcore: registered new interface driver usbhid [ 4.084615] usbhid: USB HID core driver [ 4.088658] u32 classifier [ 4.091371] Actions configured [ 4.094792] Netfilter messages via NETLINK v0.30. [ 4.099516] nfnl_acct: registering with nfnetlink. [ 4.104356] nf_conntrack version 0.5.0 (16119 buckets, 64476 max) [ 4.110608] ctnetlink v0.93: registering with nfnetlink. [ 4.115961] ip_set: protocol 6 [ 4.119202] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.124592] TCP: cubic registered [ 4.127937] NET: Registered protocol family 10 [ 4.132864] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 4.138373] sit: IPv6 over IPv4 tunneling driver [ 4.143613] NET: Registered protocol family 17 [ 4.148116] Bridge firewalling registered [ 4.152162] 8021q: 802.1Q VLAN Support v1.8 [ 4.156400] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 4.164421] registered taskstats version 1 [ 4.169113] mvebu-rtc f10a3800.rtc: setting system clock to 2022-12-04 10:00:58 UTC (1670148058) [ 4.178408] Freeing unused kernel memory: 232K (c06ad000 - c06e7000) Augusta INIT. [ 4.215343] UBI: attaching mtd0 to ubi0 [ 4.574496] UBI: scanning is finished [ 4.583451] UBI: attached mtd0 (name "fw", size 128 MiB) to ubi0 [ 4.589474] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.596289] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.603006] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.609905] UBI: good PEBs: 1016, bad PEBs: 8, corrupted PEBs: 0 [ 4.615930] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.623088] UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1088336177 [ 4.632154] UBI: available PEBs: 10, total reserved PEBs: 1006, PEBs reserved for bad PEB handling: 12 [ 4.641497] UBI: background thread "ubi_bgt0d" started, PID 1110 Normal Action check ponit P1 [ 4.668961] UBIFS: background thread "ubifs_bgt0_0" started, PID 1116 [ 4.697264] UBIFS: recovery needed [ 4.775437] UBIFS: recovery completed [ 4.779152] UBIFS: mounted UBI device 0, volume 0, name "fw" [ 4.784837] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.793999] UBIFS: FS size: 124309504 bytes (118 MiB, 979 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs) [ 4.803854] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 4.809702] UBIFS: media format: w4/r0 (latest is w4/r0), UUID A9932983-E00A-4D8E-AA5B-75B91BF53F88, small LPT model check ponit P2 check ponit P3 Waiting partition table @ 0 secs. Waiting partition table @ 1 secs. Waiting partition table @ 2 secs. Waiting partition table @ 3 secs. Waiting partition table @ 4 secs. Waiting partition table @ 5 secs. Waiting partition table @ 6 secs. Waiting partition table @ 7 secs. Waiting partition table @ 8 secs. Waiting partition table @ 9 secs. Waiting partition table @ 10 secs. Waiting partition table @ 11 secs. Waiting partition table @ 12 secs. Waiting partition table @ 13 secs. Waiting partition table @ 14 secs. OS_BLOCK_DEVICE_PATH: ,fstype: Abnormal case HDD not existed exit_code:4 [ 21.586324] pool #1: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added Ubuntu 12.04.4 LTS APOLLORD ttyS0 APOLLORD login:
BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01 (Apr 03 2018 - 10:46:04) Marvell version: 2015_T1.0p5 Board: A38x-Customer-Board-0 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1066 [MHz] L2 @ 533 [MHz] TClock @ 250 [MHz] DDR @ 533 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB NAND: 128 MiB MMC: mv_sdh: 0 SF: Detected W25Q16 with page size 4 KiB, total 2 MiB USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x3fec0000:0x3ff95dc0 BSS: 0x3ffef7dc Stack: 0x3f9aff20 Heap: 0x3f9b0000:0x3fec0000 U-Boot Environment: 0x00100000:0x00110000 (SPI) Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | SGMII | 0x01 | egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 3 2 1 0 Reset SCSI AHCI init for unit0 Target spinup took 0 ms. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: TOSHIBA MQ01ABD0 Rev: AX0C Type: Hard Disk Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Found 1 device(s). (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found USB1: Port (usbActive) : 0 Interface (usbType = 3) : Only one active controller supported! Skipping USB1 initialization. lowlevel init failed scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Creating 1 MTD partitions on "nand0": 0x000000000000-0x000008000000 : "mtd=0" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=0" UBI: MTD device size: 128 MiB UBI: number of good PEBs: 1016 UBI: number of bad PEBs: 8 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 12 UBI: total number of reserved PEBs: 1004 UBI: number of PEBs reserved for bad PEB handling: 10 UBI: max/mean erase counter: 3/1 UBI: mtd1 is detached from ubi0 Creating 1 MTD partitions on "nand0": 0x000000000000-0x000008000000 : "mtd=0" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=0" UBI: MTD device size: 128 MiB UBI: number of good PEBs: 1016 UBI: number of bad PEBs: 8 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 12 UBI: total number of reserved PEBs: 1004 UBI: number of PEBs reserved for bad PEB handling: 10 UBI: max/mean erase counter: 3/1 UBIFS: recovery needed UBIFS: recovery deferred UBIFS: mounted UBI device 0, volume 0, name "fw" UBIFS: mounted read-only UBIFS: file system size: 124309504 bytes (121396 KiB, 118 MiB, 979 LEBs) UBIFS: journal size: 6221824 bytes (6076 KiB, 5 MiB, 49 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 5182151 bytes (5060 KiB) Loading file '/boot/uImage' to addr 0x02000000 with size 3802456 (0x003a0558)... Done Loading file '/boot/device.dtb' to addr 0x01000000 with size 14977 (0x00003a81)... Done Loading file '/boot/initramfs.img' to addr 0x02500000 with size 33508338 (0x01ff4bf2)... Done bootargs=mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 ## Booting kernel from Legacy Image at 02000000 ... Image Name: Apollo Kernel Created: 2018-02-22 7:09:40 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3802392 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02500000 ... Image Name: ramdisk_0.01.0000.32 Created: 2016-03-21 11:01:43 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 33508274 Bytes = 32 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Only one active controller supported! Skipping USB1 stop. failed to stop USB controller 1 Loading Kernel Image ... OK OK Loading Device Tree to 00ff9000, end 00fffa80 ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.10.70-svn5196 (root@ApolloFW) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #47 SMP Thu Feb 22 15:09:27 CST 2018 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Marvell Armada 385 Reference Design [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @c0fa7000 s7424 r8192 d13056 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260594 [ 0.000000] Kernel command line: mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1024MB = 1024MB total [ 0.000000] Memory: 998936k/998936k available, 49640k reserved, 254976K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xfff00000 ( 247 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0700000 ( 775 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc06acc8c (6804 kB) [ 0.000000] .init : 0xc06ad000 - 0xc06e7d00 ( 236 kB) [ 0.000000] .data : 0xc06e8000 - 0xc073c320 ( 337 kB) [ 0.000000] .bss : 0xc073c320 - 0xc079a91c ( 378 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] [ 0.000000] LSP version: linux-3.10.70-2015_T1.1p7 [ 0.000000] [ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B [ 0.000000] Console: colour dummy device 80x30 [ 0.000573] Calibrating delay loop... 2125.00 BogoMIPS (lpj=10625024) [ 0.060046] pid_max: default: 32768 minimum: 301 [ 0.060123] Mount-cache hash table entries: 512 [ 0.060513] CPU: Testing write buffer coherency: ok [ 0.060644] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.060684] Setting up static identity map for 0xc0519218 - 0xc0519270 [ 0.060861] mvebu-pmsu: Initializing Power Management Service Unit [ 0.060904] Initializing CPU Reset module [ 1.060036] CPU1: failed to come online [ 1.060057] Brought up 1 CPUs [ 1.060063] SMP: Total of 1 processors activated (2125.00 BogoMIPS). [ 1.060067] CPU: All CPU(s) started in SVC mode. [ 1.060355] devtmpfs: initialized [ 1.063170] mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 [ 1.063344] pinctrl core: initialized pinctrl subsystem [ 1.063490] NET: Registered protocol family 16 [ 1.064059] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.066621] irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated [ 1.067091] irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated [ 1.079996] bio: create slab <bio-0> at 0 [ 1.080453] mvebu-pcie pcie-controller.3: PCIe0.0: link down [ 1.080479] mvebu-pcie pcie-controller.3: PCIe1.0: link down [ 1.080611] mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 [ 1.080621] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.080629] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.080637] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.080918] PCI: bus0: Fast back to back transfers disabled [ 1.080927] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.080935] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.081037] PCI: bus1: Fast back to back transfers enabled [ 1.081149] PCI: bus2: Fast back to back transfers enabled [ 1.081183] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.081194] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.081204] PCI: enabling device 0000:00:01.0 (0140 -> 0143) [ 1.081211] PCI: enabling device 0000:00:02.0 (0140 -> 0143) [ 1.081629] SCSI subsystem initialized [ 1.082165] usbcore: registered new interface driver usbfs [ 1.082237] usbcore: registered new interface driver hub [ 1.082324] usbcore: registered new device driver usb [ 1.082497] pps_core: LinuxPPS API ver. 1 registered [ 1.082502] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.082555] PTP clock support registered [ 1.083030] Switching to clocksource armada_370_xp_clocksource [ 1.089899] NET: Registered protocol family 2 [ 1.090361] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 1.090459] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.090557] TCP: Hash tables configured (established 8192 bind 8192) [ 1.090599] TCP: reno registered [ 1.090608] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.090633] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.090766] NET: Registered protocol family 1 [ 1.090947] RPC: Registered named UNIX socket transport module. [ 1.090952] RPC: Registered udp transport module. [ 1.090956] RPC: Registered tcp transport module. [ 1.090960] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.091065] Unpacking initramfs... [ 2.659423] Freeing initrd memory: 32716K (c2501000 - c44f4000) [ 2.660373] bounce pool size: 64 pages [ 2.660640] exFAT: Version 1.2.9 [ 2.660783] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.660865] NTFS driver 2.1.30 [Flags: R/O]. [ 2.660887] fuse init (API version 7.22) [ 2.661202] msgmni has been set to 1516 [ 2.661856] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 2.661864] io scheduler noop registered [ 2.661868] io scheduler deadline registered [ 2.661881] io scheduler cfq registered (default) [ 2.662532] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.662992] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.703504] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 2.733484] mv_xor f1060800.xor: freeing 1 in use descriptors! [ 2.733494] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 2.733637] mv_xor f1060900.xor: Marvell shared XOR driver [ 2.773498] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 2.803483] mv_xor f1060900.xor: freeing 1 in use descriptors! [ 2.803493] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 2.845141] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.866257] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A [ 3.516600] console [ttyS0] enabled [ 3.522878] loop: module loaded [ 3.526384] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.535208] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.544711] scsi0 : ahci_mv_platform [ 3.548512] scsi1 : ahci_mv_platform [ 3.552280] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 [ 3.560233] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 [ 3.569451] armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC [ 3.583835] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 3.595906] Bad block table found at page 65472, version 0x01 [ 3.602017] Bad block table found at page 65408, version 0x01 [ 3.609229] 1 cmdlinepart partitions found on MTD device armada-nand [ 3.615616] Creating 1 MTD partitions on "armada-nand": [ 3.620856] 0x000000000000-0x000008000000 : "fw" [ 3.627213] m25p80 spi0.0: w25q16 (2048 Kbytes) [ 3.631760] 3 cmdlinepart partitions found on MTD device spi0.0 [ 3.637711] Creating 3 MTD partitions on "spi0.0": [ 3.642514] 0x000000000000-0x000000100000 : "uboot" [ 3.648016] 0x000000100000-0x000000110000 : "env" [ 3.653311] 0x000000110000-0x000000200000 : "others" [ 3.660053] SoC: model = 0x6810, revision = 0x4 [ 3.664747] mvPncVirtBase = 0xf0c00000, pncTcamSize = 1024 [ 3.670245] o 2 Giga ports supported [ 3.674017] o NETA acceleration mode 4 [ 3.677948] o BM supported for CPU: 4 BM pools [ 3.682575] o PnC supported (Enabled) [ 3.686432] o RX Queue support: 8 Queues * 256 Descriptors [ 3.692102] o TX Queue support: 8 Queues * 532 Descriptors [ 3.697782] o GSO supported [ 3.700755] o GRO supported [ 3.703738] o Receive checksum offload supported [ 3.708539] o Transmit checksum offload supported [ 3.713436] o Driver ERROR statistics enabled [ 3.717975] o Driver INFO statistics enabled [ 3.722426] o Driver DEBUG statistics enabled [ 3.726973] [ 3.729570] port #0: is_sgmii=0, is_rgmii=1, phy_addr=0 [ 3.734869] o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 [ 3.743191] [ 3.744684] o Port 0 is connected to Linux netdevice [ 3.751830] o eth0, ifindex = 2, GbE port = 0 [ 3.759979] giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) [ 3.766094] [ 3.767714] port #1: is_sgmii=1, is_rgmii=0, phy_addr=1 [ 3.772956] o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048 [ 3.781279] [ 3.782773] o Port 1 is connected to Linux netdevice [ 3.789150] o eth1, ifindex = 3, GbE port = 1 [ 3.797302] giga p=1: mtu=1500, mac=52:c8:cb:47:48:63 (random) [ 3.803245] [ 3.805327] libphy: orion_mdio_bus: probed [ 3.811102] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.817664] ehci-pci: EHCI PCI platform driver [ 3.822208] ehci-orion: EHCI orion driver [ 3.826326] orion-ehci f1058000.usb: EHCI Host Controller [ 3.831753] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 3.839413] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 [ 3.863060] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 3.869365] hub 1-0:1.0: USB hub found [ 3.873144] hub 1-0:1.0: 1 port detected [ 3.877417] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.882752] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 3.890402] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 [ 3.896516] hub 2-0:1.0: USB hub found [ 3.900282] hub 2-0:1.0: 1 port detected [ 3.904301] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.909632] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 3.917210] ata2: SATA link down (SStatus 0 SControl 300) [ 3.922936] hub 3-0:1.0: USB hub found [ 3.926781] hub 3-0:1.0: 1 port detected [ 3.930823] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.936177] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 3.943878] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 [ 3.949993] hub 4-0:1.0: USB hub found [ 3.953769] hub 4-0:1.0: 1 port detected [ 3.957781] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.963123] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 3.970953] hub 5-0:1.0: USB hub found [ 3.974730] hub 5-0:1.0: 1 port detected [ 3.978972] usbcore: registered new interface driver usb-storage [ 3.985536] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 3.992832] i2c /dev entries driver [ 4.007095] armada_thermal f10e4078.thermal: Overheat threshold between 92..107 [ 4.015006] orion_wdt: Initial timeout 171 sec [ 4.019537] cpuidle: using governor ladder [ 4.023737] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 [ 4.033076] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) [ 4.041604] mvCesaInit: channels=2, session=640, queue=256 [ 4.060740] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode [ 4.069834] cesadev_init(c06c6c88) [ 4.073667] usbcore: registered new interface driver usbhid [ 4.079253] usbhid: USB HID core driver [ 4.083270] u32 classifier [ 4.085983] Actions configured [ 4.089394] Netfilter messages via NETLINK v0.30. [ 4.094127] nfnl_acct: registering with nfnetlink. [ 4.098959] nf_conntrack version 0.5.0 (16119 buckets, 64476 max) [ 4.105217] ctnetlink v0.93: registering with nfnetlink. [ 4.110560] ip_set: protocol 6 [ 4.113809] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.119191] TCP: cubic registered [ 4.122539] NET: Registered protocol family 10 [ 4.127477] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 4.132974] sit: IPv6 over IPv4 tunneling driver [ 4.137788] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.144343] NET: Registered protocol family 17 [ 4.148856] Bridge firewalling registered [ 4.152903] 8021q: 802.1Q VLAN Support v1.8 [ 4.157141] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 4.165187] registered taskstats version 1 [ 4.169994] mvebu-rtc f10a3800.rtc: setting system clock to 2022-12-05 09:57:26 UTC (1670234246) [ 4.197179] ata1.00: ATA-8: TOSHIBA MQ01ABD050V, AX0C1Q, max UDMA/100 [ 4.203648] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 4.211813] ata1.00: configured for UDMA/100 [ 4.216314] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MQ01ABD0 AX0C PQ: 0 ANSI: 5 [ 4.224901] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 4.232403] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.237980] sd 0:0:0:0: [sda] Write Protect is off [ 4.242835] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.359891] sda: sda1 sda2 [ 4.363404] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.368148] Freeing unused kernel memory: 232K (c06ad000 - c06e7000) Augusta INIT. [ 4.404964] UBI: attaching mtd0 to ubi0 [ 4.764106] UBI: scanning is finished [ 4.773039] UBI: attached mtd0 (name "fw", size 128 MiB) to ubi0 [ 4.779074] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.785887] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.792604] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.799499] UBI: good PEBs: 1016, bad PEBs: 8, corrupted PEBs: 0 [ 4.805523] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.812676] UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1088336177 [ 4.821747] UBI: available PEBs: 10, total reserved PEBs: 1006, PEBs reserved for bad PEB handling: 12 [ 4.831090] UBI: background thread "ubi_bgt0d" started, PID 1120 Normal Action check ponit P1 [ 4.858550] UBIFS: background thread "ubifs_bgt0_0" started, PID 1126 [ 4.886847] UBIFS: recovery needed [ 4.965193] UBIFS: recovery completed [ 4.968908] UBIFS: mounted UBI device 0, volume 0, name "fw" [ 4.974594] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.983756] UBIFS: FS size: 124309504 bytes (118 MiB, 979 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs) [ 4.993610] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 4.999459] UBIFS: media format: w4/r0 (latest is w4/r0), UUID A9932983-E00A-4D8E-AA5B-75B91BF53F88, small LPT model check ponit P2 check ponit P3 8 0 488386584 sda OS_BLOCK_DEVICE_PATH: /dev/sda1 ,fstype: EXT4 HDD Step 1 check ok Got abnormal shutdown flag. FSCK first. check result:0 [ 14.980287] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 15.029303] Adding 1952764k swap on /dev/sda2. Priority:-1 extents:1 across:1952764k swapon ret:0 exit_code:0 check ponit P4 check ponit P5 tar protect before switch cleanup keys [ 15.907404] UBIFS: un-mount UBI device 0, volume 0 [ 15.912217] UBIFS: background thread "ubifs_bgt0_0" stops [ 15.922195] UBI: detaching mtd0 from ubi0 [ 15.926724] UBI: mtd0 is detached from ubi0 switch root switch_root: failed to mount moving /run to /mnt/HDD/run: Invalid argument switch_root: forcing unmount of /run HDD INIT phase. [ 16.109217] UBI: attaching mtd0 to ubi0 [ 16.468222] UBI: scanning is finished [ 16.477155] UBI: attached mtd0 (name "fw", size 128 MiB) to ubi0 [ 16.483193] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 16.489998] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 16.496723] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 16.503619] UBI: good PEBs: 1016, bad PEBs: 8, corrupted PEBs: 0 [ 16.509639] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 16.516797] UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1088336177 [ 16.525869] UBI: available PEBs: 10, total reserved PEBs: 1006, PEBs reserved for bad PEB handling: 12 [ 16.535213] UBI: background thread "ubi_bgt0d" started, PID 1214 [ 16.585525] UBIFS: background thread "ubifs_bgt0_0" started, PID 1217 [ 16.631231] UBIFS: mounted UBI device 0, volume 0, name "fw" [ 16.636916] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 16.646078] UBIFS: FS size: 124309504 bytes (118 MiB, 979 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs) [ 16.655934] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 16.661783] UBIFS: media format: w4/r0 (latest is w4/r0), UUID A9932983-E00A-4D8E-AA5B-75B91BF53F88, small LPT model just do it 1 Entering HDD init. Ubuntu 12.04.4 LTS Apollo883975 ttyS0 Apollo883975 login: [ 23.306932] pool #1: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added Ubuntu 12.04.4 LTS Apollo883975 ttyS0 Apollo883975 login:
cat screenlog.0 BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01 (Apr 03 2018 - 10:46:04) Marvell version: 2015_T1.0p5 Board: A38x-Customer-Board-0 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1066 [MHz] L2 @ 533 [MHz] TClock @ 250 [MHz] DDR @ 533 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB NAND: 128 MiB MMC: mv_sdh: 0 SF: Detected W25Q16 with page size 4 KiB, total 2 MiB USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x3fec0000:0x3ff95dc0 BSS: 0x3ffef7dc Stack: 0x3f9aff20 Heap: 0x3f9b0000:0x3fec0000 U-Boot Environment: 0x00100000:0x00110000 (SPI) Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | SGMII | 0x01 | egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=scsi reset;if ${usb_check}; then run nand_boot; else run usb0_boot;run nand_boot; fi; bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=3 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:58:23:33 eth1mtu=1500 eth2addr=00:50:43:58:9d:33 eth2mtu=1500 eth3addr=00:50:43:23:9d:58 eth3mtu=1500 ethact=egiga0 ethaddr=00:50:43:9d:23:33 ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x.dtb ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=30.0.0.2 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x2000000 loads_echo=0 mtdids=nand0=armada-nand mtdids_nand=nand0=armada-nand mtdids_spi=spi0=spi0.0 mtdparts=mtdparts=armada-nand:-fw) mtdparts_nand=mtdparts=armada-nand:-(fw) mtdparts_spi=spi0.0:1m(uboot),64k(env),-(others) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:33:9d:58 nandEcc=nfcConfig=4bitecc nand_boot=setenv mtdids "$mtdids_nand";setenv mtdparts "$mtdparts_nand";ubi part fw;ubi part fw;ubifsmount fw;ubifsload $loadaddr /boot/uImage;ubifsload $fdtaddr /boot/device.dtb;ubifsload $rdaddr /boot/initramfs.img;setenv mtdids "$mtdids_nand;$mtdids_spi";setenv mtdparts "$mtdparts_nand;$mtdparts_spi";setenv bootargs $mtdparts $console;print bootargs;bootm $loadaddr $rdaddr $fdtaddr netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rdaddr=0x2500000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=30.0.0.121 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb0_boot=ext4load usb 0:1 $loadaddr /diag/uImage;ext4load usb 0:1 $fdtaddr /diag/device.dtb;setenv mtdids "$mtdids_nand;$mtdids_spi";setenv mtdparts "$mtdparts_nand;$mtdparts_spi";setenv bootargs $mtdparts $console root=/dev/sdb1 rw rootdelay=3 init=/init rootfstype=ext4;print bootargs;bootm $loadaddr - $fdtaddr usbActive=0 usbType=3 usb_check=usb reset vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3826/65532 bytes Marvell>>
Re: Promise Apollo Cloud - Armada 385 December 05, 2022 07:13AM |
Registered: 1 year ago Posts: 7 |
usb0_boot=ext4load usb 0:1 $loadaddr /diag/uImage;ext4load usb 0:1 $fdtaddr /diag/device.dtb;setenv mtdids "$mtdids_nand;$mtdids_spi";setenv mtdparts "$mtdparts_nand;$mtdparts_spi";setenv bootargs $mtdparts $console root=/dev/sdb1 rw rootdelay=3 init=/init rootfstype=ext4;print bootargs;bootm $loadaddr - $fdtaddr
Hit any key to stop autoboot: 0 Marvell>> usb start (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found USB1: Port (usbActive) : 0 Interface (usbType = 3) : Only one active controller supported! Skipping USB1 initialization. lowlevel init failed scanning usb for storage devices... 1 Storage Device(s) found ####usb_read 0: 6, addr: 2000000 scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>> usb storage Device 0: Vendor: SanDisk Rev: 8.02 Prod: Cruzer Blade Type: Removable Hard Disk Capacity: 7663.9 MB = 7.4 GB (15695871 x 512) Marvell>> run usb0 usb0Mode usb0_boot Marvell>> run usb0_boot 5234615 bytes read in 585 ms (8.5 MiB/s) 16319 bytes read in 336 ms (46.9 KiB/s) bootargs=mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 root=/dev/sdb1 rw rootdelay=3 init=/init rootfstype=ext4 ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-5.13.8-mvebu-tld-1 Created: 2022-12-05 11:52:52 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5234551 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Only one active controller supported! Skipping USB1 stop. failed to stop USB controller 1 Loading Kernel Image ... OK OK Loading Device Tree to 00ff9000, end 00ffffbe ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 [ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: WD My Cloud EX2100 [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000][ T0] Kernel command line: [ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 1021136K/1048576K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 27440K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 [ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000001][ T0] sched_clock: 64 bits at 533MHz, resolution 1ns, wraps every 2199023255551ns [ 0.000028][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x7aed16d152, max_idle_ns: 440795225656 ns [ 0.000056][ T0] Switching to timer-based delay loop, resolution 1ns [ 0.000328][ T0] Ignoring duplicate/late registration of read_current_timer delay [ 0.000343][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.001031][ T0] Console: colour dummy device 80x30 [ 0.001561][ T0] printk: console [tty0] enabled [ 0.001596][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1066.00 BogoMIPS (lpj=5330000) [ 0.001629][ T0] pid_max: default: 32768 minimum: 301 [ 0.001801][ T0] LSM: Security Framework initializing [ 0.001884][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001914][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002667][ T0] CPU: Testing write buffer coherency: ok [ 0.002708][ T0] CPU0: Spectre v2: using BPIALL workaround [ 0.002879][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.003480][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.003625][ T1] mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 [ 0.003784][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.003930][ T1] rcu: Hierarchical SRCU implementation. [ 0.004587][ T1] smp: Bringing up secondary CPUs ... [ 0.005081][ T1] Booting CPU 1 [ 1.040143][ T1] CPU1: failed to come online [ 1.040234][ T1] smp: Brought up 1 node, 1 CPU [ 1.040254][ T1] SMP: Total of 1 processors activated (1066.00 BogoMIPS). [ 1.040276][ T1] CPU: All CPU(s) started in SVC mode. [ 1.040691][ T1] devtmpfs: initialized [ 1.043664][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.043937][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 1.043986][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 1.050335][ T24] wait_for_initramfs() called before rootfs_initcalls [ 1.072401][ T1] prandom32: self test passed (less than 6 bits correlated) [ 1.072433][ T1] prandom: seed boundary self test passed [ 1.074402][ T1] prandom: 100 self tests passed [ 1.074419][ T1] pinctrl core: initialized pinctrl subsystem [ 1.076006][ T1] NET: Registered protocol family 16 [ 1.076703][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.077458][ T1] audit: initializing netlink subsys (disabled) [ 1.078850][ T36] audit: type=2000 audit(1.070:1): state=initialized audit_enabled=0 res=1 [ 1.080282][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 1.080444][ T1] cpuidle: using governor ladder [ 1.080502][ T1] cpuidle: using governor menu [ 1.080544][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 1.080570][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 1.080757][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 1.080787][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 1.340841][ T1] raid6: int32x8 gen() 195 MB/s [ 1.510658][ T1] raid6: int32x8 xor() 134 MB/s [ 1.680197][ T1] raid6: int32x4 gen() 224 MB/s [ 1.850246][ T1] raid6: int32x4 xor() 142 MB/s [ 2.020155][ T1] raid6: int32x2 gen() 358 MB/s [ 2.190213][ T1] raid6: int32x2 xor() 204 MB/s [ 2.360168][ T1] raid6: int32x1 gen() 398 MB/s [ 2.530139][ T1] raid6: int32x1 xor() 157 MB/s [ 2.530157][ T1] raid6: using algorithm int32x1 gen() 398 MB/s [ 2.530175][ T1] raid6: .... xor() 157 MB/s, rmw enabled [ 2.530191][ T1] raid6: using intx1 recovery algorithm [ 2.530592][ T1] fbcon: Taking over console [ 2.531064][ T1] vgaarb: loaded [ 2.531668][ T1] SCSI subsystem initialized [ 2.533665][ T1] usbcore: registered new interface driver usbfs [ 2.533783][ T1] usbcore: registered new interface driver hub [ 2.533887][ T1] usbcore: registered new device driver usb [ 2.534522][ T1] mc: Linux media interface: v0.10 [ 2.534624][ T1] videodev: Linux video capture interface: v2.00 [ 2.534994][ T1] pps_core: LinuxPPS API ver. 1 registered [ 2.535018][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 2.535107][ T1] PTP clock support registered [ 2.541142][ T1] clocksource: Switched to clocksource arm_global_timer [ 2.581533][ T1] VFS: Disk quotas dquot_6.6.0 [ 2.581637][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.607153][ T1] NET: Registered protocol family 2 [ 2.607340][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 2.612025][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 2.612093][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 2.612189][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 2.612303][ T1] TCP: Hash tables configured (established 8192 bind 8192) [ 2.612477][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 2.612551][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 2.612602][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 2.612784][ T1] NET: Registered protocol family 1 [ 2.621994][ T1] RPC: Registered named UNIX socket transport module. [ 2.622025][ T1] RPC: Registered udp transport module. [ 2.622043][ T1] RPC: Registered tcp transport module. [ 2.622059][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.622081][ T1] PCI: CLS 0 bytes, default 64 [ 2.622110][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 2.622544][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 3.556955][ T1] Initialise system trusted keyrings [ 3.557012][ T1] Key type blacklist registered [ 3.557748][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 3.557865][ T1] zbud: loaded [ 3.559452][ T1] NFS: Registering the id_resolver key type [ 3.559496][ T1] Key type id_resolver registered [ 3.559515][ T1] Key type id_legacy registered [ 3.559551][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.559579][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 3.559601][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.636203][ T1] xor: measuring software checksum speed [ 3.641927][ T1] arm4regs : 1738 MB/sec [ 3.649451][ T1] 8regs : 1310 MB/sec [ 3.656593][ T1] 32regs : 1386 MB/sec [ 3.656612][ T1] xor: using function: arm4regs (1738 MB/sec) [ 3.656636][ T1] async_tx: api initialized (async) [ 3.656655][ T1] Key type asymmetric registered [ 3.656671][ T1] Asymmetric key parser 'x509' registered [ 3.656802][ T1] bounce: pool size: 64 pages [ 3.656957][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 3.657055][ T1] io scheduler bfq registered [ 3.659434][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 3.663085][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 3.663946][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 3.665544][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 3.721853][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.723843][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 3.781845][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.928172][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.955062][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 15625000) is a 16550A [ 4.962209][ T1] printk: console [ttyS0] enabled [ 4.988817][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, base_baud = 15625000) is a 16550A [ 5.000192][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 5.010082][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 5.018606][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 5.027381][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 5.037263][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 5.048768][ T1] scsi host0: ahci-mvebu [ 5.054098][ T1] scsi host1: ahci-mvebu [ 5.058423][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 53 [ 5.067680][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 53 [ 5.077721][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 5.086060][ T1] nand: Hynix H27U1G8F2BTR-BC [ 5.090626][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 5.099653][ T1] Bad block table found at page 65472, version 0x01 [ 5.106854][ T1] Bad block table found at page 65408, version 0x01 [ 5.113836][ T1] 8 fixed-partitions partitions found on MTD device pxa3xx_nand-0 [ 5.121648][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 5.127780][ T1] 0x000000000000-0x000000500000 : "U-Boot" [ 5.134834][ T1] 0x000000500000-0x000000f00000 : "uImage" [ 5.142583][ T1] 0x000000a00000-0x000001900000 : "uRamdisk" [ 5.150426][ T1] 0x000000f00000-0x00001d700000 : "image.cfs" [ 5.157168][ T1] mtd: partition "image.cfs" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x7100000 [ 5.170294][ T1] 0x00001c800000-0x000039f00000 : "rescue_fw" [ 5.177077][ T1] mtd: partition "rescue_fw" is out of reach -- disabled [ 5.185304][ T1] 0x00001d700000-0x00003c200000 : "config" [ 5.191002][ T1] mtd: partition "config" is out of reach -- disabled [ 5.199633][ T1] 0x00001eb00000-0x00003e000000 : "reserve1" [ 5.206305][ T1] mtd: partition "reserve1" is out of reach -- disabled [ 5.214452][ T1] 0x00001f500000-0x00003f400000 : "reserve2" [ 5.220326][ T1] mtd: partition "reserve2" is out of reach -- disabled [ 5.232128][ T1] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff [ 5.240404][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 5.249198][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 5.261689][ T1] libphy: Fixed MDIO Bus: probed [ 5.271554][ T1] libphy: orion_mdio_bus: probed [ 5.280788][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 5.296739][ T1] mvneta f1070000.ethernet eth0: Using random mac address d2:ba:35:34:e1:8d [ 5.313134][ T1] mvneta f1034000.ethernet eth1: Using random mac address 2a:dc:bc:26:12:a9 [ 5.324699][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.332654][ T1] ehci-pci: EHCI PCI platform driver [ 5.337976][ T1] ehci-orion: EHCI orion driver [ 5.343257][ T1] orion-ehci f1058000.usb: EHCI Host Controller [ 5.349468][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 5.357998][ T1] orion-ehci f1058000.usb: irq 49, io mem 0xf1058000 [ 5.391158][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 5.398039][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 5.407097][ T1222] ata1: SATA link down (SStatus 0 SControl 300) [ 5.413250][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.421255][ T1227] ata2: SATA link down (SStatus 0 SControl 300) [ 5.427440][ T1] usb usb1: Product: EHCI Host Controller [ 5.433058][ T1] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd [ 5.440271][ T1] usb usb1: SerialNumber: f1058000.usb [ 5.446209][ T1] hub 1-0:1.0: USB hub found [ 5.451083][ T1] hub 1-0:1.0: 1 port detected [ 5.457027][ T1] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 5.464034][ T1] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 5.472466][ T1] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 5.482981][ T1] xhci-hcd f10f0000.usb3: irq 56, io mem 0xf10f0000 [ 5.489741][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 5.498789][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.506784][ T1] usb usb2: Product: xHCI Host Controller [ 5.512415][ T1] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 5.519589][ T1] usb usb2: SerialNumber: f10f0000.usb3 [ 5.525585][ T1] hub 2-0:1.0: USB hub found [ 5.530447][ T1] hub 2-0:1.0: 1 port detected [ 5.535560][ T1] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 5.542021][ T1] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 5.550268][ T1] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 5.557518][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.566596][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 5.575629][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.583622][ T1] usb usb3: Product: xHCI Host Controller [ 5.589227][ T1] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 5.596425][ T1] usb usb3: SerialNumber: f10f0000.usb3 [ 5.602387][ T1] hub 3-0:1.0: USB hub found [ 5.607236][ T1] hub 3-0:1.0: 1 port detected [ 5.612665][ T1] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 5.618724][ T1] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 5.627744][ T1] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 5.637843][ T1] xhci-hcd f10f8000.usb3: irq 57, io mem 0xf10f8000 [ 5.644776][ T1] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 5.653816][ T1] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.661807][ T1] usb usb4: Product: xHCI Host Controller [ 5.667411][ T1] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 5.674798][ T1] usb usb4: SerialNumber: f10f8000.usb3 [ 5.680785][ T1] hub 4-0:1.0: USB hub found [ 5.685699][ T1] hub 4-0:1.0: 1 port detected [ 5.690829][ T1] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 5.697322][ T1] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 5.705625][ T1] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 5.712915][ T1] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.721898][ T1] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 5.730924][ T1] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.738915][ T1] usb usb5: Product: xHCI Host Controller [ 5.744537][ T1] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 5.751783][ T1] usb usb5: SerialNumber: f10f8000.usb3 [ 5.757725][ T1] hub 5-0:1.0: USB hub found [ 5.762630][ T1] hub 5-0:1.0: 1 port detected [ 5.767996][ T1] usbcore: registered new interface driver usblp [ 5.775170][ T1] usbcore: registered new interface driver usb-storage [ 5.782511][ T1] mousedev: PS/2 mouse device common for all mice [ 5.790903][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 5.798493][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-05T13:00:13 UTC (1670245213) [ 5.809142][ T1] i2c /dev entries driver [ 5.814593][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 5.823048][ T25] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 5.831349][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 5.843906][ T1] orion_wdt: Initial timeout 171 sec [ 5.850714][ T1] device-mapper: uevent: version 1.0.3 [ 5.856677][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 5.866419][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 5.873801][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 5.881181][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 5.888580][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 5.895440][ T1] device-mapper: raid: Loading target version 1.15.1 [ 5.905152][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered [ 5.913509][ T1] hid: raw HID events driver (C) Jiri Kosina [ 5.920381][ T1] usbcore: registered new interface driver usbhid [ 5.927274][ T1] usbhid: USB HID core driver [ 5.932420][ T1] drop_monitor: Initializing network drop monitor service [ 5.939797][ T1] NET: Registered protocol family 10 [ 5.946522][ T1] Segment Routing with IPv6 [ 5.950913][ T1] RPL Segment Routing with IPv6 [ 5.955788][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 5.963829][ T1] NET: Registered protocol family 17 [ 5.969951][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 5.975106][ T1] Key type dns_resolver registered [ 5.980118][ T1] ThumbEE CPU extension supported. [ 5.985227][ T1] Registering SWP/SWPB emulation handler [ 5.991072][ T1] registered taskstats version 1 [ 5.996104][ T1] Loading compiled-in X.509 certificates [ 6.002142][ T25] usb 2-1: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 2.00 [ 6.011076][ T25] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 6.019311][ T1] zswap: loaded using pool lzo/zbud [ 6.024709][ T1] Key type ._fscrypt registered [ 6.029447][ T1] Key type .fscrypt registered [ 6.034143][ T25] usb 2-1: Product: Cruzer Blade [ 6.038965][ T25] usb 2-1: Manufacturer: SanDisk [ 6.043799][ T1] Key type fscrypt-provisioning registered [ 6.050925][ T1] Key type big_key registered [ 6.055597][ T25] usb 2-1: SerialNumber: 0831401AF491FF0F [ 6.062534][ T25] usb-storage 2-1:1.0: USB Mass Storage device detected [ 6.070160][ T1] Key type encrypted registered [ 6.078940][ T25] scsi host2: usb-storage 2-1:1.0 [ 6.084688][ T1] md: Waiting for all devices to be available before autodetect [ 6.093024][ T1] md: If you don't use raid, use raid=noautodetect [ 6.099421][ T1] md: Autodetecting RAID arrays. [ 6.104296][ T1] md: autorun ... [ 6.107807][ T1] md: ... autorun DONE. [ 6.112244][ T1] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 6.120474][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 6.129678][ T1] 1f00 5120 mtdblock0 [ 6.129685][ T1] (driver?) [ 6.137745][ T1] 1f01 10240 mtdblock1 [ 6.137752][ T1] (driver?) [ 6.145749][ T1] 1f02 15360 mtdblock2 [ 6.145755][ T1] (driver?) [ 6.153755][ T1] 1f03 115712 mtdblock3 [ 6.153762][ T1] (driver?) [ 6.161765][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 6.170772][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.8-mvebu-tld-1 #1.0 [ 6.178647][ T1] Hardware name: Marvell Armada 380/385 (Device Tree) [ 6.185301][ T1] [<c01153e8>] (unwind_backtrace) from [<c01100f8>] (show_stack+0x10/0x14) [ 6.193805][ T1] [<c01100f8>] (show_stack) from [<c0b05d18>] (dump_stack+0x80/0x9c) [ 6.201775][ T1] [<c0b05d18>] (dump_stack) from [<c0b01150>] (panic+0xe4/0x2f0) [ 6.209397][ T1] [<c0b01150>] (panic) from [<c1001ad8>] (mount_block_root+0x1b4/0x238) [ 6.217632][ T1] [<c1001ad8>] (mount_block_root) from [<c1001c4c>] (mount_root+0xf0/0x11c) [ 6.226213][ T1] [<c1001c4c>] (mount_root) from [<c1001dbc>] (prepare_namespace+0x144/0x180) [ 6.234966][ T1] [<c1001dbc>] (prepare_namespace) from [<c1001640>] (kernel_init_freeable+0x230/0x29c) [ 6.244592][ T1] [<c1001640>] (kernel_init_freeable) from [<c0b0d9ac>] (kernel_init+0x8/0x118) [ 6.253524][ T1] [<c0b0d9ac>] (kernel_init) from [<c0100150>] (ret_from_fork+0x14/0x24) [ 6.261840][ T1] Exception stack(0xc18cffb0 to 0xc18cfff8) [ 6.267618][ T1] ffa0: 00000000 00000000 00000000 00000000 [ 6.276538][ T1] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 6.285456][ T1] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 6.292812][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
Re: Promise Apollo Cloud - Armada 385 December 05, 2022 12:03PM |
Registered: 1 year ago Posts: 7 |
setenv usb0_boot 'ext4load usb 0:1 $loadaddr /boot/uImage;ext2load usb 0:1 $load_initrd_addr /boot/uInitrd;setenv mtdids "$mtdids_nand;$mtdids_spi";setenv mtdparts "$mtdparts_nand;$mtdparts_spi";setenv bootargs $mtdparts $console root=/dev/sdb1 rw rootdelay=13 rootfstype=ext4;print bootargs;bootm $loadaddr $load_initrd_addr'
Marvell>> usb start Only one active controller supported! Skipping USB1 stop. failed to stop USB controller 1 (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found USB1: Port (usbActive) : 0 Interface (usbType = 3) : Only one active controller supported! Skipping USB1 initialization. lowlevel init failed scanning usb for storage devices... 1 Storage Device(s) found ####usb_read 0: 6, addr: 2000000 scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>> usb part Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 44 15679396 6f180f60-01 83 Marvell>> setenv usb0_boot 'ext4load usb 0:1 $loadaddr /boot/uImage;ext2load usb 0:1 $load_initrd_addr /boot/uInitrd;setenv mtdids "$mtdids_nand;$mtdids_spi";setenv mtdparts "$mtdparts_nand;$mtdparts_spi";setenv bootargs $mtdparts $console root=/dev/sdb1 rw rootdelay=13 rootfstype=ext4;print bootargs;bootm $loadaddr $load_initrd_addr' Marvell>> run usb0_boot 5234615 bytes read in 555 ms (9 MiB/s) ** No boot file defined ** bootargs=mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 root=/dev/sdb1 rw rootdelay=13 rootfstype=ext4 ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-5.13.8-mvebu-tld-1 Created: 2022-12-05 11:52:52 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5234551 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Only one active controller supported! Skipping USB1 stop. failed to stop USB controller 1 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 [ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: WD My Cloud EX2100 [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000][ T0] Kernel command line: mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 root=/dev/sdb1 rw rootdelay=13 rootfstype=ext4 [ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 1021136K/1048576K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 27440K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 [ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000002][ T0] sched_clock: 64 bits at 533MHz, resolution 1ns, wraps every 2199023255551ns [ 0.000029][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x7aed16d152, max_idle_ns: 440795225656 ns [ 0.000056][ T0] Switching to timer-based delay loop, resolution 1ns [ 0.000326][ T0] Ignoring duplicate/late registration of read_current_timer delay [ 0.000340][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.001031][ T0] Console: colour dummy device 80x30 [ 0.001066][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1066.00 BogoMIPS (lpj=5330000) [ 0.001083][ T0] pid_max: default: 32768 minimum: 301 [ 0.001248][ T0] LSM: Security Framework initializing [ 0.001321][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001338][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002077][ T0] CPU: Testing write buffer coherency: ok [ 0.002108][ T0] CPU0: Spectre v2: using BPIALL workaround [ 0.002269][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002856][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.002988][ T1] mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 [ 0.003135][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.003272][ T1] rcu: Hierarchical SRCU implementation. [ 0.003920][ T1] smp: Bringing up secondary CPUs ... [ 0.004404][ T1] Booting CPU 1 [ 1.040142][ T1] CPU1: failed to come online [ 1.040222][ T1] smp: Brought up 1 node, 1 CPU [ 1.040234][ T1] SMP: Total of 1 processors activated (1066.00 BogoMIPS). [ 1.040245][ T1] CPU: All CPU(s) started in SVC mode. [ 1.040655][ T1] devtmpfs: initialized [ 1.043909][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.044165][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 1.044196][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 1.050334][ T24] wait_for_initramfs() called before rootfs_initcalls [ 1.072579][ T1] prandom32: self test passed (less than 6 bits correlated) [ 1.072597][ T1] prandom: seed boundary self test passed [ 1.074557][ T1] prandom: 100 self tests passed [ 1.074564][ T1] pinctrl core: initialized pinctrl subsystem [ 1.076130][ T1] NET: Registered protocol family 16 [ 1.076961][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.077690][ T1] audit: initializing netlink subsys (disabled) [ 1.079067][ T36] audit: type=2000 audit(1.070:1): state=initialized audit_enabled=0 res=1 [ 1.080488][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 1.080646][ T1] cpuidle: using governor ladder [ 1.080681][ T1] cpuidle: using governor menu [ 1.080868][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 1.080881][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 1.081055][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 1.081072][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 1.340804][ T1] raid6: int32x8 gen() 195 MB/s [ 1.510620][ T1] raid6: int32x8 xor() 135 MB/s [ 1.680203][ T1] raid6: int32x4 gen() 224 MB/s [ 1.850229][ T1] raid6: int32x4 xor() 138 MB/s [ 2.020204][ T1] raid6: int32x2 gen() 358 MB/s [ 2.190225][ T1] raid6: int32x2 xor() 203 MB/s [ 2.360157][ T1] raid6: int32x1 gen() 398 MB/s [ 2.530145][ T1] raid6: int32x1 xor() 166 MB/s [ 2.530155][ T1] raid6: using algorithm int32x1 gen() 398 MB/s [ 2.530163][ T1] raid6: .... xor() 166 MB/s, rmw enabled [ 2.530170][ T1] raid6: using intx1 recovery algorithm [ 2.530995][ T1] vgaarb: loaded [ 2.531588][ T1] SCSI subsystem initialized [ 2.533591][ T1] usbcore: registered new interface driver usbfs [ 2.533693][ T1] usbcore: registered new interface driver hub [ 2.533783][ T1] usbcore: registered new device driver usb [ 2.534402][ T1] mc: Linux media interface: v0.10 [ 2.534494][ T1] videodev: Linux video capture interface: v2.00 [ 2.534845][ T1] pps_core: LinuxPPS API ver. 1 registered [ 2.534857][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 2.534927][ T1] PTP clock support registered [ 2.541155][ T1] clocksource: Switched to clocksource arm_global_timer [ 2.581546][ T1] VFS: Disk quotas dquot_6.6.0 [ 2.581631][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.607003][ T1] NET: Registered protocol family 2 [ 2.607156][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 2.611126][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 2.611380][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 2.611464][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 2.611567][ T1] TCP: Hash tables configured (established 8192 bind 8192) [ 2.611737][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 2.611797][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 2.611836][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 2.612009][ T1] NET: Registered protocol family 1 [ 2.622034][ T1] RPC: Registered named UNIX socket transport module. [ 2.622050][ T1] RPC: Registered udp transport module. [ 2.622058][ T1] RPC: Registered tcp transport module. [ 2.622065][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.622076][ T1] PCI: CLS 0 bytes, default 64 [ 2.622256][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 2.622678][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 3.556326][ T1] Initialise system trusted keyrings [ 3.556368][ T1] Key type blacklist registered [ 3.557095][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 3.557197][ T1] zbud: loaded [ 3.558774][ T1] NFS: Registering the id_resolver key type [ 3.558806][ T1] Key type id_resolver registered [ 3.558816][ T1] Key type id_legacy registered [ 3.558843][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.558858][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 3.558867][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.634113][ T1] xor: measuring software checksum speed [ 3.639786][ T1] arm4regs : 1738 MB/sec [ 3.647335][ T1] 8regs : 1310 MB/sec [ 3.654469][ T1] 32regs : 1386 MB/sec [ 3.654479][ T1] xor: using function: arm4regs (1738 MB/sec) [ 3.654494][ T1] async_tx: api initialized (async) [ 3.654506][ T1] Key type asymmetric registered [ 3.654513][ T1] Asymmetric key parser 'x509' registered [ 3.654627][ T1] bounce: pool size: 64 pages [ 3.654779][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 3.654865][ T1] io scheduler bfq registered [ 3.657213][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 3.659762][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 3.662335][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 3.663927][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 3.721868][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.723941][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 3.781861][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.926223][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.934128][ T1] printk: console [ttyS0] disabled [ 3.954738][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 15625000) is a 16550A [ 4.968912][ T1] printk: console [ttyS0] enabled [ 4.995537][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, base_baud = 15625000) is a 16550A [ 5.006906][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 5.016782][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 5.025292][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 5.034042][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 5.043903][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 5.055381][ T1] scsi host0: ahci-mvebu [ 5.060602][ T1] scsi host1: ahci-mvebu [ 5.065318][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 53 [ 5.074307][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 53 [ 5.084649][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 5.092722][ T1] nand: Hynix H27U1G8F2BTR-BC [ 5.097275][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 5.106277][ T1] Bad block table found at page 65472, version 0x01 [ 5.113464][ T1] Bad block table found at page 65408, version 0x01 [ 5.120336][ T1] 8 fixed-partitions partitions found on MTD device pxa3xx_nand-0 [ 5.128207][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 5.134364][ T1] 0x000000000000-0x000000500000 : "U-Boot" [ 5.141443][ T1] 0x000000500000-0x000000f00000 : "uImage" [ 5.149112][ T1] 0x000000a00000-0x000001900000 : "uRamdisk" [ 5.156987][ T1] 0x000000f00000-0x00001d700000 : "image.cfs" [ 5.163698][ T1] mtd: partition "image.cfs" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x7100000 [ 5.176791][ T1] 0x00001c800000-0x000039f00000 : "rescue_fw" [ 5.183550][ T1] mtd: partition "rescue_fw" is out of reach -- disabled [ 5.191765][ T1] 0x00001d700000-0x00003c200000 : "config" [ 5.197453][ T1] mtd: partition "config" is out of reach -- disabled [ 5.206066][ T1] 0x00001eb00000-0x00003e000000 : "reserve1" [ 5.212730][ T1] mtd: partition "reserve1" is out of reach -- disabled [ 5.220760][ T1] 0x00001f500000-0x00003f400000 : "reserve2" [ 5.227434][ T1] mtd: partition "reserve2" is out of reach -- disabled [ 5.238466][ T1] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff [ 5.246728][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 5.255741][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 5.267995][ T1] libphy: Fixed MDIO Bus: probed [ 5.277666][ T1] libphy: orion_mdio_bus: probed [ 5.287109][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 5.302968][ T1] mvneta f1070000.ethernet eth0: Using random mac address 36:58:64:d2:50:29 [ 5.319385][ T1] mvneta f1034000.ethernet eth1: Using random mac address 9a:fc:ed:1c:fa:b9 [ 5.330814][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.338878][ T1] ehci-pci: EHCI PCI platform driver [ 5.344389][ T1] ehci-orion: EHCI orion driver [ 5.349473][ T1] orion-ehci f1058000.usb: EHCI Host Controller [ 5.355789][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 5.364270][ T1] orion-ehci f1058000.usb: irq 49, io mem 0xf1058000 [ 5.391166][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 5.398034][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 5.407068][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.415047][ T1228] ata2: SATA link down (SStatus 0 SControl 300) [ 5.421189][ T1] usb usb1: Product: EHCI Host Controller [ 5.426784][ T1] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd [ 5.434019][ T1] usb usb1: SerialNumber: f1058000.usb [ 5.439957][ T1] hub 1-0:1.0: USB hub found [ 5.444878][ T1] hub 1-0:1.0: 1 port detected [ 5.450775][ T1] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 5.457760][ T1] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 5.466152][ T1] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 5.477249][ T1] xhci-hcd f10f0000.usb3: irq 56, io mem 0xf10f0000 [ 5.484056][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 5.493094][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.501044][ T1] usb usb2: Product: xHCI Host Controller [ 5.506654][ T1] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 5.513827][ T1] usb usb2: SerialNumber: f10f0000.usb3 [ 5.519802][ T1] hub 2-0:1.0: USB hub found [ 5.524694][ T1] hub 2-0:1.0: 1 port detected [ 5.529742][ T1] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 5.536172][ T1] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 5.544459][ T1] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 5.551738][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.560672][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 5.569703][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.577679][ T1] usb usb3: Product: xHCI Host Controller [ 5.583291][ T1] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 5.590454][ T1] usb usb3: SerialNumber: f10f0000.usb3 [ 5.596396][ T1] hub 3-0:1.0: USB hub found [ 5.601257][ T1] hub 3-0:1.0: 1 port detected [ 5.606679][ T1] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 5.612770][ T1223] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.620407][ T1] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 5.628775][ T1] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 5.638940][ T1] xhci-hcd f10f8000.usb3: irq 57, io mem 0xf10f8000 [ 5.645745][ T1] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 5.654778][ T1] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.662942][ T1] usb usb4: Product: xHCI Host Controller [ 5.668539][ T1] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 5.675724][ T1] usb usb4: SerialNumber: f10f8000.usb3 [ 5.681692][ T1] hub 4-0:1.0: USB hub found [ 5.686545][ T1] hub 4-0:1.0: 1 port detected [ 5.691694][ T1] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 5.697737][ T1] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 5.706402][ T1] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 5.713615][ T1] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.722672][ T1] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 5.731702][ T1] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.739652][ T1] usb usb5: Product: xHCI Host Controller [ 5.745330][ T1] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 5.752511][ T1] usb usb5: SerialNumber: f10f8000.usb3 [ 5.758448][ T1] hub 5-0:1.0: USB hub found [ 5.763337][ T1] hub 5-0:1.0: 1 port detected [ 5.768692][ T1] usbcore: registered new interface driver usblp [ 5.775846][ T1] usbcore: registered new interface driver usb-storage [ 5.783187][ T1] mousedev: PS/2 mouse device common for all mice [ 5.791753][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 5.798043][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-05T17:46:39 UTC (1670262399) [ 5.809742][ T1] i2c /dev entries driver [ 5.813996][ T25] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 5.822408][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 5.831741][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 5.844381][ T1] orion_wdt: Initial timeout 171 sec [ 5.851433][ T1] device-mapper: uevent: version 1.0.3 [ 5.857153][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 5.866885][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 5.874214][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 5.881616][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 5.889004][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 5.895852][ T1] device-mapper: raid: Loading target version 1.15.1 [ 5.902455][ T1223] ata1.00: ATA-8: ST9250311CS, SC16, max UDMA/133 [ 5.908751][ T1223] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.919250][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered [ 5.927563][ T1223] ata1.00: configured for UDMA/133 [ 5.932710][ T1] hid: raw HID events driver (C) Jiri Kosina [ 5.939617][ T1] usbcore: registered new interface driver usbhid [ 5.946581][ T1] usbhid: USB HID core driver [ 5.951568][ T23] scsi 0:0:0:0: Direct-Access ATA ST9250311CS SC16 PQ: 0 ANSI: 5 [ 5.960863][ T1] drop_monitor: Initializing network drop monitor service [ 5.969206][ T7] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB) [ 5.978575][ T1] NET: Registered protocol family 10 [ 5.984278][ T7] sd 0:0:0:0: [sda] Write Protect is off [ 5.990832][ T1] Segment Routing with IPv6 [ 5.995407][ T7] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.005286][ T1] RPL Segment Routing with IPv6 [ 6.010075][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 6.017302][ T25] usb 2-1: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 2.00 [ 6.028398][ T1] NET: Registered protocol family 17 [ 6.034405][ T25] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 6.042455][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 6.047396][ T1] Key type dns_resolver registered [ 6.052448][ T25] usb 2-1: Product: Cruzer Blade [ 6.057352][ T7] sda: sda1 [ 6.060733][ T1] ThumbEE CPU extension supported. [ 6.065946][ T25] usb 2-1: Manufacturer: SanDisk [ 6.070760][ T25] usb 2-1: SerialNumber: 0831401AF491FF0F [ 6.077145][ T7] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 6.083710][ T1] Registering SWP/SWPB emulation handler [ 6.090304][ T1] registered taskstats version 1 [ 6.095735][ T25] usb-storage 2-1:1.0: USB Mass Storage device detected [ 6.102939][ T1] Loading compiled-in X.509 certificates [ 6.108897][ T1] zswap: loaded using pool lzo/zbud [ 6.114711][ T25] scsi host2: usb-storage 2-1:1.0 [ 6.121115][ T1] Key type ._fscrypt registered [ 6.125962][ T1] Key type .fscrypt registered [ 6.130599][ T1] Key type fscrypt-provisioning registered [ 6.137763][ T1] Key type big_key registered [ 6.143209][ T1] Key type encrypted registered [ 6.151293][ T1] Waiting 13 sec before mounting root device... [ 7.121688][ T7] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 8.02 PQ: 0 ANSI: 0 CCS [ 7.132155][ T1493] sd 2:0:0:0: [sdb] 15695871 512-byte logical blocks: (8.04 GB/7.48 GiB) [ 7.141596][ T1493] sd 2:0:0:0: [sdb] Write Protect is off [ 7.147282][ T1493] sd 2:0:0:0: [sdb] No Caching mode page found [ 7.153385][ T1493] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 7.164359][ T1493] sdb: sdb1 [ 7.169261][ T1493] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 19.681165][ T1] md: Waiting for all devices to be available before autodetect [ 19.688682][ T1] md: If you don't use raid, use raid=noautodetect [ 19.695073][ T1] md: Autodetecting RAID arrays. [ 19.699882][ T1] md: autorun ... [ 19.703392][ T1] md: ... autorun DONE. [ 19.728091][ T1] EXT4-fs (sdb1): recovery complete [ 19.733220][ T1] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 19.743313][ T1] VFS: Mounted root (ext4 filesystem) on device 8:17. [ 19.758184][ T1] devtmpfs: mounted [ 19.763578][ T1] Freeing unused kernel memory: 1024K [ 19.769389][ T1] Checked W+X mappings: passed, no W+X pages found [ 19.775803][ T1] Run /sbin/init as init process [ 19.799307][ C0] random: fast init done INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Files under mount point '/run' will be hidden. ... (warning). Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 23.064211][ T1721] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 23.119444][ T1721] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 23.426608][ T1725] usbcore: registered new interface driver uas done. Setting hostname to 'debian'...done. Activating swap:. [ 31.093753][ C0] random: crng init done [ 38.134357][ T1877] EXT4-fs (sdb1): re-mounted. Opts: (null). Quota mode: none. Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sdb1 e2fsck 1.46.2 (28-Feb-2021) rootfs: clean, 22181/490560 files, 334420/1959924 blocks . [ 38.385953][ T1890] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files... Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. Initializing random number generator...done. [ 40.809486][ T2307] mvneta f1070000.ethernet eth0: validation of rgmii-id with support 0000000,00000000,00006280 and advertisement 0000000,00000000,00002280 failed: -22 [ 40.826540][ T2307] mvneta f1070000.ethernet eth0: could not attach PHY: -22 [ 40.833765][ T2307] mvneta f1070000.ethernet eth0: cannot probe MDIO bus Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ RTNETLINK answers: Invalid argument Listening on LPF/eth0/c2:90:9a:b0:fd:d6 Sending on LPF/eth0/c2:90:9a:b0:fd:d6 Sending on Socket/fallback receive_packet failed on eth0: Network is down DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 send_packet: Network is down dhclient.c:2446: Failed to send 300 byte long packet over eth0 interface. DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 send_packet: Network is down dhclient.c:2446: Failed to send 300 byte long packet over eth0 interface. DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13 send_packet: Network is down dhclient.c:2446: Failed to send 300 byte long packet over eth0 interface. DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 send_packet: Network is down dhclient.c:2446: Failed to send 300 byte long packet over eth0 interface. DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 send_packet: Network is down dhclient.c:2446: Failed to send 300 byte long packet over eth0 interface. DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 17 send_packet: Network is down dhclient.c:2446: Failed to send 300 byte long packet over eth0 interface. No DHCPOFFERS received. No working leases in persistent database - sleeping. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Not starting NFS kernel daemon: no exports. ... (warning). Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2443 (syslogd) . Starting periodic command scheduler: cron. Starting system message bus: dbus. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting NTP server: ntpd. Starting OpenBSD Secure Shell server: sshdsshd: no hostkeys available -- exiting. failed! Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2477 (klogd) . Running local boot scripts (/etc/rc.local) ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519 Starting OpenBSD Secure Shell server: sshd . Cannot read environment, using default Cannot read default environment from file <13>Dec 5 09:48:34 root[2572]: Cannot read u-boot env ethaddr . Debian GNU/Linux 11 debian ttyS0 debian login: root Password: Linux debian 5.13.8-mvebu-tld-1 #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Mon Sep 27 22:36:43 PDT 2021 from 192.168.0.100 on pts/0 debian WD My Cloud EX2100 Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 Debian 11.0 Mon Dec 5 09:48:40 PST 2022 up 1 minute root@debian:~# uname -a Linux debian 5.13.8-mvebu-tld-1 #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 armv7l GNU/Linux
Re: Promise Apollo Cloud - Armada 385 December 05, 2022 06:02PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Promise Apollo Cloud - Armada 385 December 06, 2022 04:32PM |
Registered: 1 year ago Posts: 7 |
Hit any key to stop autoboot: 0 Marvell>> setenv mtdids "$mtdids_nand";setenv mtdparts "$mtdparts_nand" Marvell>> usb start (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found USB1: Port (usbActive) : 0 Interface (usbType = 3) : Only one active controller supported! Skipping USB1 initialization. lowlevel init failed scanning usb for storage devices... 1 Storage Device(s) found ####usb_read 0: 6, addr: 2000000 scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>> usb part Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 44 15679396 6f180f60-01 83 Marvell>> ubi part fw;ubi part fw;ubifsmount fw; Creating 1 MTD partitions on "nand0": 0x000000000000-0x000008000000 : "mtd=0" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=0" UBI: MTD device size: 128 MiB UBI: number of good PEBs: 1016 UBI: number of bad PEBs: 8 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 12 UBI: total number of reserved PEBs: 1004 UBI: number of PEBs reserved for bad PEB handling: 10 UBI: max/mean erase counter: 3/1 UBI: mtd1 is detached from ubi0 Creating 1 MTD partitions on "nand0": 0x000000000000-0x000008000000 : "mtd=0" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=0" UBI: MTD device size: 128 MiB UBI: number of good PEBs: 1016 UBI: number of bad PEBs: 8 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 12 UBI: total number of reserved PEBs: 1004 UBI: number of PEBs reserved for bad PEB handling: 10 UBI: max/mean erase counter: 3/1 UBIFS: recovery needed UBIFS: recovery deferred UBIFS: mounted UBI device 0, volume 0, name "fw" UBIFS: mounted read-only UBIFS: file system size: 124309504 bytes (121396 KiB, 118 MiB, 979 LEBs) UBIFS: journal size: 6221824 bytes (6076 KiB, 5 MiB, 49 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 5182151 bytes (5060 KiB) Marvell>> ubifsls /boot 33508338 Thu Oct 13 06:08:29 2016 initramfs.img 1024228 Thu Dec 01 17:46:23 2022 uboot.bin 3802456 Thu Dec 01 17:46:23 2022 uImage 14977 Tue Oct 10 19:46:19 2017 device.dtb Marvell>> ubifsload $fdtaddr /boot/device.dtb Loading file '/boot/device.dtb' to addr 0x01000000 with size 14977 (0x00003a81)... Done Marvell>> ext4write usb 0:1 /boot/device.dtb $fdtaddr 14977 File System is consistent update journal finished
dtc -I dtb -O dts -f device.dtb -o devicetree_apollo.dts
/dts-v1/; / { #address-cells = <0x1>; #size-cells = <0x1>; model = "Marvell Armada 385 Reference Design"; compatible = "marvell,a385-db-gp", "marvell,armada385", "marvell,armada38x"; chosen { bootargs = "console=ttyS0,115200 earlyprintk"; }; aliases { gpio0 = "/soc/internal-regs/gpio@18100"; gpio1 = "/soc/internal-regs/gpio@18140"; }; memory { device_type = "memory"; reg = <0x0 0x10000000>; }; soc { compatible = "marvell,armada380-mbus", "simple-bus"; #address-cells = <0x2>; #size-cells = <0x1>; controller = <0x1>; interrupt-parent = <0x2>; pcie-mem-aperture = <0xe0000000 0x8000000>; pcie-io-aperture = <0xe8000000 0x100000>; ranges = <0xf0010000 0x0 0xf1000000 0x100000 0x11d0000 0x0 0xfff00000 0x100000 0x9190000 0x0 0xf1100000 0x10000 0x9150000 0x0 0xf1110000 0x10000 0xc040000 0x0 0xf1200000 0x100000 0xb040000 0x0 0xf1300000 0x100000>; bootrom { compatible = "marvell,bootrom"; reg = <0x11d0000 0x0 0x200000>; }; cesa-sram { compatible = "marvell,cesa-sram"; reg = <0x9190000 0x0 0x10000 0x9150000 0x0 0x10000>; }; devbus-bootcs { compatible = "marvell,mvebu-devbus"; reg = <0xf0010000 0x10400 0x8>; ranges = <0x0 0x12f0000 0x0 0xffffffff>; #address-cells = <0x1>; #size-cells = <0x1>; clocks = <0x3 0x0>; status = "disabled"; }; devbus-cs0 { compatible = "marvell,mvebu-devbus"; reg = <0xf0010000 0x10408 0x8>; ranges = <0x0 0x13e0000 0x0 0xffffffff>; #address-cells = <0x1>; #size-cells = <0x1>; clocks = <0x3 0x0>; status = "disabled"; }; devbus-cs1 { compatible = "marvell,mvebu-devbus"; reg = <0xf0010000 0x10410 0x8>; ranges = <0x0 0x13d0000 0x0 0xffffffff>; #address-cells = <0x1>; #size-cells = <0x1>; clocks = <0x3 0x0>; status = "disabled"; }; devbus-cs2 { compatible = "marvell,mvebu-devbus"; reg = <0xf0010000 0x10418 0x8>; ranges = <0x0 0x13b0000 0x0 0xffffffff>; #address-cells = <0x1>; #size-cells = <0x1>; clocks = <0x3 0x0>; status = "disabled"; }; devbus-cs3 { compatible = "marvell,mvebu-devbus"; reg = <0xf0010000 0x10420 0x8>; ranges = <0x0 0x1370000 0x0 0xffffffff>; #address-cells = <0x1>; #size-cells = <0x1>; clocks = <0x3 0x0>; status = "disabled"; }; internal-regs { compatible = "simple-bus"; #address-cells = <0x1>; #size-cells = <0x1>; ranges = <0x0 0xf0010000 0x0 0x100000>; coherency-fabric@21010 { compatible = "marvell,armada-380-coherency-fabric"; reg = <0x21010 0x1c>; }; mvebu-sar@18600 { compatible = "marvell,armada-380-core-clock"; reg = <0x18600 0x4>; #clock-cells = <0x1>; linux,phandle = <0x3>; phandle = <0x3>; }; corediv-clock@e4250 { compatible = "marvell,armada-38x-corediv-clock"; reg = <0xe4250 0x8>; #clock-cells = <0x1>; clocks = <0x4>; clock-output-names = "nand"; linux,phandle = <0x9>; phandle = <0x9>; }; cpurst@20800 { compatible = "marvell,armada-380-cpu-reset"; reg = <0x20800 0x10>; #reset-cells = <0x1>; linux,phandle = <0xe>; phandle = <0xe>; }; mpcore-soc-ctrl@20d20 { compatible = "marvell,armada-380-mpcore-soc-ctrl"; reg = <0x20d20 0x6c>; }; mdio { #address-cells = <0x1>; #size-cells = <0x0>; compatible = "marvell,orion-mdio"; reg = <0x72004 0x4>; clocks = <0x5 0x4>; ethernet-phy@0 { reg = <0x0>; linux,phandle = <0x7>; phandle = <0x7>; }; ethernet-phy@1 { reg = <0x1>; linux,phandle = <0x8>; phandle = <0x8>; }; }; bm_pnc@c0000 { compatible = "marvell,neta_bm_pnc"; reg = <0xc8000 0xac 0xb8000 0x48>; clocks = <0x5 0xd 0x5 0x1d>; neta_cap_bm = <0x3>; pnc_tcam_size = <0x400>; }; ethernet@70000 { compatible = "marvell,neta"; reg = <0x70000 0x4000>; interrupts-extended = <0x6 0x8>; clocks = <0x5 0x4>; tx-csum-limit = <0x2648>; status = "okay"; mac-address = [00 50 43 02 02 01]; eth,port-num = <0x0>; eth,port-mtu = <0x5dc>; phy = <0x7>; phy-mode = "rgmii"; }; ethernet@30000 { compatible = "marvell,neta"; reg = <0x30000 0x4000>; interrupts-extended = <0x6 0xa>; clocks = <0x5 0x3>; tx-csum-limit = <0x800>; status = "okay"; eth,port-num = <0x1>; eth,port-mtu = <0x5dc>; phy = <0x8>; phy-mode = "sgmii"; }; ethernet@34000 { compatible = "marvell,neta"; reg = <0x34000 0x4000>; interrupts-extended = <0x6 0xc>; clocks = <0x5 0x2>; tx-csum-limit = <0x800>; status = "disabled"; eth,port-num = <0x2>; eth,port-mtu = <0x5dc>; }; clock-gating-control@18220 { compatible = "marvell,armada-380-gating-clock"; reg = <0x18220 0x4>; clocks = <0x3 0x0>; #clock-cells = <0x1>; linux,phandle = <0x5>; phandle = <0x5>; }; gpio@18100 { compatible = "marvell,orion-gpio"; reg = <0x18100 0x40>; ngpios = <0x20>; gpio-controller; #gpio-cells = <0x2>; interrupt-controller; #interrupt-cells = <0x2>; interrupts = <0x0 0x35 0x4 0x0 0x36 0x4 0x0 0x37 0x4 0x0 0x38 0x4>; }; gpio@18140 { compatible = "marvell,orion-gpio"; reg = <0x18140 0x40>; ngpios = <0x1c>; gpio-controller; #gpio-cells = <0x2>; interrupt-controller; #interrupt-cells = <0x2>; interrupts = <0x0 0x3a 0x4 0x0 0x3b 0x4 0x0 0x3c 0x4 0x0 0x3d 0x4>; linux,phandle = <0xc>; phandle = <0xc>; }; i2c@11000 { compatible = "marvell,mv64xxx-i2c"; reg = <0x11000 0x20>; #address-cells = <0x1>; #size-cells = <0x0>; interrupts = <0x0 0x2 0x4>; timeout-ms = <0x3e8>; clocks = <0x3 0x0>; status = "okay"; clock-frequency = <0x186a0>; }; i2c@11100 { compatible = "marvell,mv64xxx-i2c"; reg = <0x11100 0x20>; #address-cells = <0x1>; #size-cells = <0x0>; interrupts = <0x0 0x3 0x4>; timeout-ms = <0x3e8>; clocks = <0x3 0x0>; status = "okay"; clock-frequency = <0x186a0>; }; interrupt-controller@1e001000 { compatible = "arm,cortex-a9-gic"; #interrupt-cells = <0x3>; #size-cells = <0x0>; interrupt-controller; reg = <0xd000 0x1000 0xc100 0x100>; linux,phandle = <0x2>; phandle = <0x2>; }; cache-controller { compatible = "arm,pl310-cache"; reg = <0x8000 0x1000>; cache-unified; cache-level = <0x2>; }; clock-complex@18700 { #clock-cells = <0x1>; compatible = "marvell,armada-xp-cpu-clock", "armada-380-cpu-clock"; reg = <0x18700 0xa0 0x1c054 0x40 0xe4260 0x8>; clocks = <0x3 0x1>; linux,phandle = <0xf>; phandle = <0xf>; }; mbus-controller@20000 { compatible = "marvell,mbus-controller"; reg = <0x20000 0x100 0x20180 0x20 0x20250 0x8 0x20420 0xc>; linux,phandle = <0x1>; phandle = <0x1>; }; interrupt-controller@20000 { compatible = "marvell,mpic"; reg = <0x20a00 0x2d0 0x21070 0x58 0x21870 0x190>; #interrupt-cells = <0x1>; #size-cells = <0x1>; interrupt-controller; msi-controller; interrupts = <0x1 0xf 0x4>; linux,phandle = <0x6>; phandle = <0x6>; }; pinctrl { compatible = "marvell,mv88f6820-pinctrl"; reg = <0x18000 0x20>; i2s_pins { marvell,pins = "mpp48", "mpp49", "mpp50", "mpp51", "mpp52", "mpp53"; marvell,function = "audio"; }; tdm_pins { marvell,pins = "mpp48", "mpp49", "mpp50", "mpp51", "mpp52", "mpp53"; marvell,function = "tdm2c"; }; spi1_pins { marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59"; marvell,function = "spi1"; }; pic-pins-0 { marvell,pins = "mpp33", "mpp34", "mpp35"; marvell,function = "gpio"; linux,phandle = <0xb>; phandle = <0xb>; }; }; pmsu@22000 { compatible = "marvell,armada-380-pmsu"; reg = <0x22000 0x1000>; }; sdramc@1400 { compatible = "marvell,armada-xp-sdram-controller"; reg = <0x1400 0x500>; }; rtc@a3800 { compatible = "marvell,mvebu-rtc"; reg = <0xa3800 0x20 0x184a0 0xc>; interrupts = <0x0 0x15 0x4>; }; sata@a8000 { compatible = "marvell,ahci-sata"; reg = <0xa8000 0x2000>; interrupts = <0x0 0x1a 0x4>; clocks = <0x5 0xf>; status = "okay"; }; sata@e0000 { compatible = "marvell,ahci-sata"; reg = <0xe0000 0x2000>; interrupts = <0x0 0x1c 0x4>; clocks = <0x5 0x1e>; status = "disabled"; }; tdm@b0000 { compatible = "marvell,armada-380-tdm"; reg = <0xb0000 0x5000 0x18400 0xc 0x18730 0x4>; reg-names = "tdm_regs", "pll_regs", "dco_div"; interrupts = <0x0 0x1b 0x4>; clocks = <0x5 0x19>; clock-names = "gateclk"; status = "disabled"; }; sdhci@d8000 { compatible = "marvell,armada-380-sdhci"; reg = <0xd8000 0x1000 0xdc000 0x100 0x18454 0x4>; interrupts = <0x0 0x19 0x4>; clocks = <0x5 0x11>; mrvl,clk-delay-cycles = <0x1f>; status = "okay"; broken-cd; wp-inverted; bus-width = <0x8>; }; audio-controller@e8000 { compatible = "marvell,armada-380-audio"; reg = <0xe8000 0x4000 0x18410 0xc 0x18204 0x4>; interrupts = <0x0 0x4b 0x4>; clocks = <0x5 0x0>; clock-names = "internal"; status = "disabled"; linux,phandle = <0xd>; phandle = <0xd>; }; scu@c000 { compatible = "arm,cortex-a9-scu"; reg = <0xc000 0x58>; }; serial@12000 { compatible = "snps,dw-apb-uart"; reg = <0x12000 0x100>; reg-shift = <0x2>; interrupts = <0x0 0xc 0x4>; reg-io-width = <0x1>; clocks = <0x3 0x0>; status = "okay"; }; serial@12100 { compatible = "snps,dw-apb-uart"; reg = <0x12100 0x100>; reg-shift = <0x2>; interrupts = <0x0 0xd 0x4>; reg-io-width = <0x1>; clocks = <0x3 0x0>; status = "disabled"; }; thermal@e8078 { compatible = "marvell,armada380-thermal"; reg = <0xe4078 0x4 0xe4070 0x8 0xe4100 0x20>; interrupts = <0x0 0x4e 0x4>; threshold = <0x64>; hysteresis = <0x2>; status = "okay"; }; spi@10680 { compatible = "marvell,armada-380-spi"; reg = <0x10680 0x50>; #address-cells = <0x1>; #size-cells = <0x0>; cell-index = <0x0>; interrupts = <0x0 0x3f 0x4>; clocks = <0x3 0x0>; num-cs = <0x4>; status = "okay"; spi-flash@0 { #address-cells = <0x1>; #size-cells = <0x1>; compatible = "w25q16"; reg = <0x0>; spi-max-frequency = <0x2faf080>; }; }; nand@d0000 { compatible = "marvell,armada-nand"; interrupts = <0x0 0x54 0x4>; reg = <0xd0000 0x400>; clocks = <0x9 0x0>; clock-names = "ecc_clk"; status = "okay"; #address-cells = <0x1>; #size-cells = <0x1>; nfc,nfc-mode = "normal"; nfc,nfc-dma = <0x0>; nfc,nfc-width = <0x8>; nfc,ecc-type = <0x1>; nfc,num-cs = <0x1>; }; system-controller@18200 { compatible = "marvell,armada-380-system-controller"; reg = <0x18200 0x100>; }; timer@c600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0xc600 0x20>; interrupts = <0x1 0xd 0x301>; clocks = <0x3 0x2>; }; usb@58000 { compatible = "marvell,orion-ehci"; reg = <0x58000 0x500>; interrupts = <0x0 0x12 0x4>; clocks = <0x5 0x12>; }; usb3@f0000 { compatible = "marvell,xhci-armada-380"; reg = <0xf0000 0x3fff 0xf4000 0x3fff>; interrupts = <0x0 0x10 0x4>; clocks = <0x5 0x9>; }; usb3@f8000 { compatible = "marvell,xhci-armada-380"; reg = <0xf8000 0x3fff 0xfc000 0x3fff>; interrupts = <0x0 0x11 0x4>; clocks = <0x5 0xa>; status = "okay"; }; usb3-utmi@1842 { compatible = "marvell,armada-380-usb-utmi"; reg = <0x18420 0x74 0xc0000 0x10000>; }; timer@20300 { compatible = "marvell,armada-380-timer"; reg = <0x20300 0x30 0x21040 0x30>; interrupts-extended = <0x2 0x0 0x8 0x4 0x2 0x0 0x9 0x4 0x2 0x0 0xa 0x4 0x2 0x0 0xb 0x4 0x6 0x5 0x6 0x6>; clocks = <0x3 0x2 0xa>; clock-names = "nbclk", "fixed"; }; watchdog@20300 { compatible = "marvell,armada-380-wdt"; reg = <0x20300 0x34 0x20704 0x4 0x18260 0x4>; clocks = <0x3 0x2 0xa>; clock-names = "nbclk", "fixed"; }; xor@60800 { compatible = "marvell,a38x-xor"; reg = <0x60800 0x100 0x60a00 0x100>; clocks = <0x5 0x16>; status = "okay"; xor00 { interrupts = <0x0 0x16 0x4>; dmacap,memcpy; dmacap,xor; dmacap,interrupt; dmacap,pq; }; xor01 { interrupts = <0x0 0x17 0x4>; dmacap,crc32c; dmacap,interrupt; }; }; xor@60900 { compatible = "marvell,a38x-xor"; reg = <0x60900 0x100 0x60b00 0x100>; clocks = <0x5 0x1c>; status = "okay"; xor10 { interrupts = <0x0 0x41 0x4>; dmacap,memcpy; dmacap,xor; dmacap,interrupt; dmacap,pq; }; xor11 { interrupts = <0x0 0x42 0x4>; dmacap,crc32c; dmacap,interrupt; }; }; crypto@9D000 { compatible = "marvell,armada-cesa"; reg = <0x9d000 0x1000 0x90000 0x1000 0x9f000 0x1000 0x92000 0x1000>; clocks = <0x5 0x17 0x5 0xe 0x5 0x15 0x5 0x10>; clock-names = "crypto0", "crypto0z", "crypto1", "crypto1z"; cesa,channels = <0x2>; cesa,mode = "ocf"; cesa,feature = "chain"; cesa,threshold = <0x2>; cesa,time_threshold = <0xfffff>; cesa,ctrlModel = [68 00]; cesa,ctrlRev = [02]; cesa,sramOffset = [00 40]; status = "okay"; crypto10 { interrupts = <0x0 0x13 0x4>; }; crypto11 { interrupts = <0x0 0x14 0x4>; }; }; pmu { compatible = "arm,cortex-a9-pmu"; interrupts-extended = <0x6 0x3>; }; prestera { compatible = "marvell,armada-prestera"; status = "disabled"; }; pm_pic { pinctrl-0 = <0xb>; pinctrl-names = "default"; ctrl-gpios = <0xc 0x1 0x1 0xc 0x2 0x1 0xc 0x3 0x1>; }; }; pcie-controller { compatible = "marvell,armada-38x-pcie"; status = "okay"; device_type = "pci"; #address-cells = <0x3>; #size-cells = <0x2>; msi-parent = <0x6>; bus-range = <0x0 0xff>; ranges = <0x82000000 0x0 0x80000 0xf0010000 0x80000 0x0 0x2000 0x82000000 0x0 0x40000 0xf0010000 0x40000 0x0 0x2000 0x82000000 0x0 0x44000 0xf0010000 0x44000 0x0 0x2000 0x82000000 0x0 0x48000 0xf0010000 0x48000 0x0 0x2000 0x82000000 0x1 0x0 0x8e80000 0x0 0x1 0x0 0x81000000 0x1 0x0 0x8e00000 0x0 0x1 0x0 0x82000000 0x2 0x0 0x4e80000 0x0 0x1 0x0 0x81000000 0x2 0x0 0x4e00000 0x0 0x1 0x0 0x82000000 0x3 0x0 0x4d80000 0x0 0x1 0x0 0x81000000 0x3 0x0 0x4d00000 0x0 0x1 0x0 0x82000000 0x4 0x0 0x4b80000 0x0 0x1 0x0 0x81000000 0x4 0x0 0x4b00000 0x0 0x1 0x0>; pcie@1,0 { device_type = "pci"; assigned-addresses = <0x82000800 0x0 0x80000 0x0 0x2000>; reg = <0x800 0x0 0x0 0x0 0x0>; #address-cells = <0x3>; #size-cells = <0x2>; #interrupt-cells = <0x1>; ranges = <0x82000000 0x0 0x0 0x82000000 0x1 0x0 0x1 0x0 0x81000000 0x0 0x0 0x81000000 0x1 0x0 0x1 0x0>; interrupt-map-mask = <0x0 0x0 0x0 0x0>; interrupt-map = <0x0 0x0 0x0 0x0 0x2 0x0 0x1d 0x4>; marvell,pcie-port = <0x0>; marvell,pcie-lane = <0x0>; clocks = <0x5 0x8>; status = "okay"; }; pcie@2,0 { device_type = "pci"; assigned-addresses = <0x82000800 0x0 0x40000 0x0 0x2000>; reg = <0x1000 0x0 0x0 0x0 0x0>; #address-cells = <0x3>; #size-cells = <0x2>; #interrupt-cells = <0x1>; ranges = <0x82000000 0x0 0x0 0x82000000 0x2 0x0 0x1 0x0 0x81000000 0x0 0x0 0x81000000 0x2 0x0 0x1 0x0>; interrupt-map-mask = <0x0 0x0 0x0 0x0>; interrupt-map = <0x0 0x0 0x0 0x0 0x2 0x0 0x21 0x4>; marvell,pcie-port = <0x1>; marvell,pcie-lane = <0x0>; clocks = <0x5 0x5>; status = "okay"; }; pcie@3,0 { device_type = "pci"; assigned-addresses = <0x82000800 0x0 0x44000 0x0 0x2000>; reg = <0x1800 0x0 0x0 0x0 0x0>; #address-cells = <0x3>; #size-cells = <0x2>; #interrupt-cells = <0x1>; ranges = <0x82000000 0x0 0x0 0x82000000 0x3 0x0 0x1 0x0 0x81000000 0x0 0x0 0x81000000 0x3 0x0 0x1 0x0>; interrupt-map-mask = <0x0 0x0 0x0 0x0>; interrupt-map = <0x0 0x0 0x0 0x0 0x2 0x0 0x46 0x4>; marvell,pcie-port = <0x2>; marvell,pcie-lane = <0x0>; clocks = <0x5 0x6>; status = "disabled"; }; pcie@4,0 { device_type = "pci"; assigned-addresses = <0x82000800 0x0 0x48000 0x0 0x2000>; reg = <0x2000 0x0 0x0 0x0 0x0>; #address-cells = <0x3>; #size-cells = <0x2>; #interrupt-cells = <0x1>; ranges = <0x82000000 0x0 0x0 0x82000000 0x4 0x0 0x1 0x0 0x81000000 0x0 0x0 0x81000000 0x4 0x0 0x1 0x0>; interrupt-map-mask = <0x0 0x0 0x0 0x0>; interrupt-map = <0x0 0x0 0x0 0x0 0x2 0x0 0x47 0x4>; marvell,pcie-port = <0x3>; marvell,pcie-lane = <0x0>; clocks = <0x5 0x7>; status = "disabled"; }; }; }; clocks { oscillator { compatible = "fixed-clock"; #clock-cells = <0x0>; clock-frequency = <0x17d7840>; linux,phandle = <0xa>; phandle = <0xa>; }; mainpll { compatible = "fixed-clock"; #clock-cells = <0x0>; clock-frequency = <0x77359400>; linux,phandle = <0x4>; phandle = <0x4>; }; }; switch { compatible = "marvell,mv_switch"; status = "disabled"; index = <0x0>; phy_addr = <0x2>; gbe_port = <0x0>; cpuPort = <0x6>; vid = <0x0>; port_mask = <0x7f>; connected_port_mask = <0x7f>; forced_link_port_mask = <0x60>; mtu = <0x5dc>; smi_scan_mode = <0x2>; qsgmii_module = <0x0>; gephy_on_port = <0x1f>; rgmiia_on_port = <0x60>; switch_irq = <0xffffffff>; is_speed_2000 = <0x0>; rgmii_rx_timing_delay = <0x1>; rgmii_tx_timing_delay = <0x1>; }; sound { marvell,audio-controller = <0xd>; status = "disabled"; }; spdif-out { compatible = "linux,spdif-dit"; }; spdif-in { compatible = "linux,spdif-dir"; }; cpus { #address-cells = <0x1>; #size-cells = <0x0>; clock-ranges; cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0x0>; resets = <0xe 0x0>; clocks = <0xf 0x0>; clock-latency = <0xf4240>; clock-names = "cpu0"; }; cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0x1>; resets = <0xe 0x1>; clocks = <0xf 0x0>; clock-latency = <0xf4240>; clock-names = "cpu1"; }; }; };
Re: Promise Apollo Cloud - Armada 385 December 06, 2022 05:01PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Promise Apollo Cloud - Armada 385 December 07, 2022 02:41AM |
Registered: 1 year ago Posts: 7 |
Marvell>> run usb0_boot 5233273 bytes read in 557 ms (9 MiB/s) ** No boot file defined ** bootargs=mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 root=/dev/sda1 rw rootdelay=13 rootfstype=ext4 ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-5.13.8-mvebu-tld-1 Created: 2022-12-06 22:36:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5233209 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Only one active controller supported! Skipping USB1 stop. failed to stop USB controller 1 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 [ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Marvell Armada 385 Reference Design [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000][ T0] Kernel command line: mtdparts=armada-nand:-(fw);spi0.0:1m(uboot),64k(env),-(others) console=ttyS0,115200 root=/dev/sda1 rw rootdelay=13 rootfstype=ext4 [ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 1021144K/1048576K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 27432K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x46070001 [ 0.000000][ T0] Division by zero in kernel. [ 0.000000][ T0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.8-mvebu-tld-1 #1.0 [ 0.000000][ T0] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000][ T0] [<c01153e8>] (unwind_backtrace) from [<c01100f8>] (show_stack+0x10/0x14) [ 0.000000][ T0] [<c01100f8>] (show_stack) from [<c0b05d18>] (dump_stack+0x80/0x9c) [ 0.000000][ T0] [<c0b05d18>] (dump_stack) from [<c0608fa4>] (Ldiv0+0x8/0x10) [ 0.000000][ T0] [<c0608fa4>] (Ldiv0) from [<c067c490>] (clk_cpu_recalc_rate+0x2c/0x30) [ 0.000000][ T0] [<c067c490>] (clk_cpu_recalc_rate) from [<c067735c>] (__clk_register+0x410/0x62c) [ 0.000000][ T0] [<c067735c>] (__clk_register) from [<c1028d10>] (of_cpu_clk_setup+0x200/0x2c0) [ 0.000000][ T0] [<c1028d10>] (of_cpu_clk_setup) from [<c10277f4>] (of_clk_init+0x17c/0x200) [ 0.000000][ T0] [<c10277f4>] (of_clk_init) from [<c100449c>] (time_init+0x20/0x30) [ 0.000000][ T0] [<c100449c>] (time_init) from [<c10010ec>] (start_kernel+0x59c/0x86c) [ 0.000000][ T0] [<c10010ec>] (start_kernel) from [<00000000>] (0x0) [ 0.000000][ T0] Division by zero in kernel. [ 0.000000][ T0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.8-mvebu-tld-1 #1.0 [ 0.000000][ T0] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000][ T0] [<c01153e8>] (unwind_backtrace) from [<c01100f8>] (show_stack+0x10/0x14) [ 0.000000][ T0] [<c01100f8>] (show_stack) from [<c0b05d18>] (dump_stack+0x80/0x9c) [ 0.000000][ T0] [<c0b05d18>] (dump_stack) from [<c0608fa4>] (Ldiv0+0x8/0x10) [ 0.000000][ T0] [<c0608fa4>] (Ldiv0) from [<c067c490>] (clk_cpu_recalc_rate+0x2c/0x30) [ 0.000000][ T0] [<c067c490>] (clk_cpu_recalc_rate) from [<c067735c>] (__clk_register+0x410/0x62c) [ 0.000000][ T0] [<c067735c>] (__clk_register) from [<c1028d10>] (of_cpu_clk_setup+0x200/0x2c0) [ 0.000000][ T0] [<c1028d10>] (of_cpu_clk_setup) from [<c10277f4>] (of_clk_init+0x17c/0x200) [ 0.000000][ T0] [<c10277f4>] (of_clk_init) from [<c100449c>] (time_init+0x20/0x30) [ 0.000000][ T0] [<c100449c>] (time_init) from [<c10010ec>] (start_kernel+0x59c/0x86c) [ 0.000000][ T0] [<c10010ec>] (start_kernel) from [<00000000>] (0x0) [ 0.000000][ T0] Console: colour dummy device 80x30 [ 0.000000][ T0] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns [ 0.000000][ T0] Calibrating delay loop... 2118.45 BogoMIPS (lpj=10592256) [ 0.060000][ T0] pid_max: default: 32768 minimum: 301 [ 0.060000][ T0] LSM: Security Framework initializing [ 0.060000][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.060000][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.060000][ T0] CPU: Testing write buffer coherency: ok [ 0.060000][ T0] CPU0: Spectre v2: using BPIALL workaround [ 0.060000][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.060000][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.060000][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.060000][ T1] rcu: Hierarchical SRCU implementation. [ 0.060000][ T1] smp: Bringing up secondary CPUs ... [ 0.060000][ T1] smp: Brought up 1 node, 1 CPU [ 0.060000][ T1] SMP: Total of 1 processors activated (2118.45 BogoMIPS). [ 0.060000][ T1] CPU: All CPU(s) started in SVC mode. [ 0.060000][ T1] devtmpfs: initialized [ 0.060000][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.060000][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.060000][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.070000][ T24] wait_for_initramfs() called before rootfs_initcalls [ 0.090000][ T1] prandom32: self test passed (less than 6 bits correlated) [ 0.090000][ T1] prandom: seed boundary self test passed [ 0.090000][ T1] prandom: 100 self tests passed [ 0.090000][ T1] pinctrl core: initialized pinctrl subsystem [ 0.090000][ T1] NET: Registered protocol family 16 [ 0.090000][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.100000][ T1] audit: initializing netlink subsys (disabled) [ 0.100000][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.100000][ T1] cpuidle: using governor ladder [ 0.100000][ T1] cpuidle: using governor menu [ 0.100000][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.100000][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.110000][ T35] audit: type=2000 audit(0.100:1): state=initialized audit_enabled=0 res=1 [ 0.360000][ T1] raid6: int32x8 gen() 195 MB/s [ 0.530000][ T1] raid6: int32x8 xor() 134 MB/s [ 0.700000][ T1] raid6: int32x4 gen() 224 MB/s [ 0.870000][ T1] raid6: int32x4 xor() 140 MB/s [ 1.040000][ T1] raid6: int32x2 gen() 358 MB/s [ 1.210000][ T1] raid6: int32x2 xor() 202 MB/s [ 1.380000][ T1] raid6: int32x1 gen() 398 MB/s [ 1.550000][ T1] raid6: int32x1 xor() 157 MB/s [ 1.550000][ T1] raid6: using algorithm int32x1 gen() 398 MB/s [ 1.550000][ T1] raid6: .... xor() 157 MB/s, rmw enabled [ 1.550000][ T1] raid6: using intx1 recovery algorithm [ 1.550000][ T1] vgaarb: loaded [ 1.550000][ T1] SCSI subsystem initialized [ 1.550000][ T1] usbcore: registered new interface driver usbfs [ 1.550000][ T1] usbcore: registered new interface driver hub [ 1.550000][ T1] usbcore: registered new device driver usb [ 1.550000][ T1] mc: Linux media interface: v0.10 [ 1.550000][ T1] videodev: Linux video capture interface: v2.00 [ 1.550000][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.550000][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.550000][ T1] PTP clock support registered [ 1.600000][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.600000][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.620000][ T1] NET: Registered protocol family 2 [ 1.620000][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.620000][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.620000][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.620000][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.620000][ T1] TCP: Hash tables configured (established 8192 bind 8192) [ 1.620000][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 1.620000][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.620000][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.620000][ T1] NET: Registered protocol family 1 [ 1.620000][ T1] RPC: Registered named UNIX socket transport module. [ 1.620000][ T1] RPC: Registered udp transport module. [ 1.620000][ T1] RPC: Registered tcp transport module. [ 1.620000][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.620000][ T1] PCI: CLS 0 bytes, default 64 [ 1.620000][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.620000][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.570000][ T1] Initialise system trusted keyrings [ 2.570000][ T1] Key type blacklist registered [ 2.570000][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.570000][ T1] zbud: loaded [ 2.570000][ T1] NFS: Registering the id_resolver key type [ 2.570000][ T1] Key type id_resolver registered [ 2.570000][ T1] Key type id_legacy registered [ 2.570000][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.570000][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.570000][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.570000][ T1] jitterentropy: Initialization failed with host not compliant with requirements: 2 [ 2.570000][ T1] xor: measuring software checksum speed [ 2.580000][ T1] arm4regs : -1018167296 MB/sec [ 2.590000][ T1] 8regs : -1018167296 MB/sec [ 2.600000][ T1] 32regs : -1018167296 MB/sec [ 2.600000][ T1] xor: using function: 32regs (-1018167296 MB/sec) [ 2.600000][ T1] async_tx: api initialized (async) [ 2.600000][ T1] Key type asymmetric registered [ 2.600000][ T1] Asymmetric key parser 'x509' registered [ 2.600000][ T1] bounce: pool size: 64 pages [ 2.600000][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 2.600000][ T1] io scheduler bfq registered [ 2.600000][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.740000][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.740000][ T1] printk: console [ttyS0] disabled [ 2.760000][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 41, base_baud = 15625000) is a 16550A [ 3.820000][ T1] printk: console [ttyS0] enabled [ 3.830000][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.840000][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 3.850000][ T1] libphy: Fixed MDIO Bus: probed [ 3.860000][ T1] libphy: orion_mdio_bus: probed [ 3.900000][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.900000][ T1] ehci-pci: EHCI PCI platform driver [ 3.910000][ T1] ehci-orion: EHCI orion driver [ 3.920000][ T1] orion-ehci f1058000.usb: EHCI Host Controller [ 3.920000][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 3.930000][ T1] orion-ehci f1058000.usb: irq 45, io mem 0xf1058000 [ 3.970000][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 3.970000][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.980000][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.990000][ T1] usb usb1: Product: EHCI Host Controller [ 3.990000][ T1] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd [ 4.000000][ T1] usb usb1: SerialNumber: f1058000.usb [ 4.010000][ T1] hub 1-0:1.0: USB hub found [ 4.010000][ T1] hub 1-0:1.0: 1 port detected [ 4.020000][ T1] usbcore: registered new interface driver usblp [ 4.020000][ T1] usbcore: registered new interface driver usb-storage [ 4.030000][ T1] mousedev: PS/2 mouse device common for all mice [ 4.040000][ T1] i2c /dev entries driver [ 4.040000][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 4.060000][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 4.080000][ T1] orion_wdt: Initial timeout 171 sec [ 4.080000][ T1] device-mapper: uevent: version 1.0.3 [ 4.090000][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 4.100000][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 4.110000][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 4.110000][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 4.120000][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 4.130000][ T1] device-mapper: raid: Loading target version 1.15.1 [ 4.130000][ T1] hid: raw HID events driver (C) Jiri Kosina [ 4.140000][ T1] usbcore: registered new interface driver usbhid [ 4.150000][ T1] usbhid: USB HID core driver [ 4.150000][ T1] drop_monitor: Initializing network drop monitor service [ 4.160000][ T1] NET: Registered protocol family 10 [ 4.170000][ T1] Segment Routing with IPv6 [ 4.170000][ T1] RPL Segment Routing with IPv6 [ 4.180000][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.180000][ T1] NET: Registered protocol family 17 [ 4.190000][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 4.200000][ T1] Key type dns_resolver registered [ 4.200000][ T1] ThumbEE CPU extension supported. [ 4.210000][ T1] Registering SWP/SWPB emulation handler [ 4.210000][ T1] registered taskstats version 1 [ 4.220000][ T1] Loading compiled-in X.509 certificates [ 4.220000][ T1] zswap: loaded using pool lzo/zbud [ 4.230000][ T1] Key type ._fscrypt registered [ 4.230000][ T1] Key type .fscrypt registered [ 4.240000][ T1] Key type fscrypt-provisioning registered [ 4.240000][ T1] Key type big_key registered [ 4.250000][ T1] Key type encrypted registered [ 4.260000][ T1] Waiting 13 sec before mounting root device... [ 17.760000][ T1] md: Waiting for all devices to be available before autodetect [ 17.760000][ T1] md: If you don't use raid, use raid=noautodetect [ 17.770000][ T1] md: Autodetecting RAID arrays. [ 17.770000][ T1] md: autorun ... [ 17.780000][ T1] md: ... autorun DONE. [ 17.780000][ T1] VFS: Cannot open root device "sda1" or unknown-block(0,0): error -6 [ 17.790000][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 17.800000][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 17.800000][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.8-mvebu-tld-1 #1.0 [ 17.800000][ T1] Hardware name: Marvell Armada 380/385 (Device Tree) [ 17.800000][ T1] [<c01153e8>] (unwind_backtrace) from [<c01100f8>] (show_stack+0x10/0x14) [ 17.800000][ T1] [<c01100f8>] (show_stack) from [<c0b05d18>] (dump_stack+0x80/0x9c) [ 17.800000][ T1] [<c0b05d18>] (dump_stack) from [<c0b01150>] (panic+0xe4/0x2f0) [ 17.800000][ T1] [<c0b01150>] (panic) from [<c1001ad8>] (mount_block_root+0x1b4/0x238) [ 17.800000][ T1] [<c1001ad8>] (mount_block_root) from [<c1001c4c>] (mount_root+0xf0/0x11c) [ 17.800000][ T1] [<c1001c4c>] (mount_root) from [<c1001dbc>] (prepare_namespace+0x144/0x180) [ 17.800000][ T1] [<c1001dbc>] (prepare_namespace) from [<c1001640>] (kernel_init_freeable+0x230/0x29c) [ 17.800000][ T1] [<c1001640>] (kernel_init_freeable) from [<c0b0d9ac>] (kernel_init+0x8/0x118) [ 17.800000][ T1] [<c0b0d9ac>] (kernel_init) from [<c0100150>] (ret_from_fork+0x14/0x24) [ 17.800000][ T1] Exception stack(0xc18cffb0 to 0xc18cfff8) [ 17.800000][ T1] ffa0: 00000000 00000000 00000000 00000000 [ 17.800000][ T1] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 17.800000][ T1] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 17.800000][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
Re: Promise Apollo Cloud - Armada 385 December 07, 2022 03:58PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
Updated 09 Nov 2022:
Kernel 6.0.7-mvebu-tld-1 package has been uploaded.
Download at Dropbox
linux-6.0.7-mvebu-tld-1-bodhi.tar.bz2
Re: Promise Apollo Cloud - Armada 385 December 09, 2022 02:09AM |
Registered: 1 year ago Posts: 7 |
#include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h>
Re: Promise Apollo Cloud - Armada 385 December 09, 2022 05:59PM |
Admin Registered: 13 years ago Posts: 18,821 |
dpkg -i linux-headers-6.0.7-kirkwood-tld-1_1.0_armel.deb- Install the toolchains
Re: Promise Apollo Cloud - Armada 385 December 10, 2022 03:42AM |
Registered: 1 year ago Posts: 7 |
Re: Promise Apollo Cloud - Armada 385 December 10, 2022 03:29PM |
Admin Registered: 13 years ago Posts: 18,821 |
ethtool eth0
Apollo
Re: Promise Apollo Cloud - Armada 385 December 14, 2022 09:51PM |
Re: Promise Apollo Cloud - Armada 385 January 18, 2023 11:28PM |
Registered: 9 years ago Posts: 451 |
Re: Promise Apollo Cloud - Armada 385 February 15, 2023 04:53PM |
Registered: 1 year ago Posts: 4 |
Re: Promise Apollo Cloud - Armada 385 February 15, 2023 05:26PM |
Admin Registered: 13 years ago Posts: 18,821 |
apollo
Re: Promise Apollo Cloud - Armada 385 September 23, 2023 08:20PM |
apollo
Re: Promise Apollo Cloud - Armada 385 September 24, 2023 06:04PM |
Re: Promise Apollo Cloud - Armada 385 September 24, 2023 07:24PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
from top of the board it's:
+----+----+-----+----+
|3.3V| RX | GND | TX |
+----+----+-----+----+
Re: Promise Apollo Cloud - Armada 385 September 24, 2023 10:21PM |
Registered: 9 years ago Posts: 451 |
Re: Promise Apollo Cloud - Armada 385 September 24, 2023 11:13PM |
Admin Registered: 13 years ago Posts: 18,821 |
apollo
Re: Promise Apollo Cloud - Armada 385 November 02, 2023 05:30AM |
Re: Promise Apollo Cloud - Armada 385 November 02, 2023 12:48PM |
Admin Registered: 13 years ago Posts: 18,821 |
apollo
Re: Promise Apollo Cloud - Armada 385 November 02, 2023 02:58PM |
apollo
Re: Promise Apollo Cloud - Armada 385 November 02, 2023 04:27PM |
Re: Promise Apollo Cloud - Armada 385 November 02, 2023 04:48PM |
Admin Registered: 13 years ago Posts: 18,821 |
picocom v3.1 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no hangup is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is : omap is : emap is : crcrlf,delbs, logfile is : none initstring : none exit_after is : not set exit is : no
flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 stopbits are : 1