How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition
Posted by i5Js
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition March 12, 2024 11:18PM |
Registered: 8 months ago Posts: 6 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition March 13, 2024 12:17AM |
Admin Registered: 13 years ago Posts: 18,997 |
> I didn't post anything regarding the mvneta
> problem earlier as I thought this was somehow only
> affecting my installation :)
Ah, OK :) If the next stable kernel 6.8.x does not pick this up, I will.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> problem earlier as I thought this was somehow only
> affecting my installation :)
Ah, OK :) If the next stable kernel 6.8.x does not pick this up, I will.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition March 14, 2024 04:09AM |
Registered: 8 months ago Posts: 6 |
Did anyone get the HDD Led working for the WD EX2 Ultra?
================
WD EX2 Ultra - ext3 usb kernel/rootfs, 6.6.2-mvebu/Debian/OMV, realtek-r8152 2.5GbE
Uboot - u-boot-a38x-RangerPeak_2014T3_PQ-nand_1G
Kernel Patch - mvneta.patch, linux-6.6.2-mvebu-tld-1
================
WD EX2 Ultra - ext3 usb kernel/rootfs, 6.6.2-mvebu/Debian/OMV, realtek-r8152 2.5GbE
Uboot - u-boot-a38x-RangerPeak_2014T3_PQ-nand_1G
Kernel Patch - mvneta.patch, linux-6.6.2-mvebu-tld-1
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition March 14, 2024 12:52PM |
Registered: 8 months ago Posts: 6 |
Got it working with following in /etc/rc.local
================
WD EX2 Ultra - ext3 usb kernel/rootfs, 6.6.2-mvebu/Debian/OMV, realtek-r8152 2.5GbE
Uboot - u-boot-a38x-RangerPeak_2014T3_PQ-nand_1G
Kernel Patch - mvneta.patch, linux-6.6.2-mvebu-tld-1
if [ -e /sys/class/leds/wdmcex2u\:hdd1\:blue/trigger ]; then
echo gpio > /sys/class/leds/wdmcex2u\:hdd1\:blue/trigger
echo 1 > /sys/class/leds/wdmcex2u\:hdd1\:blue/inverted
fi
if [ -e /sys/class/leds/wdmcex2u\:hdd2\:blue/trigger ]; then
echo gpio > /sys/class/leds/wdmcex2u\:hdd2\:blue/trigger
echo 1 > /sys/class/leds/wdmcex2u\:hdd2\:blue/inverted
fi
if [ -e /sys/class/leds/wdmcex2u\:hdd1\:red/trigger ]; then
echo ide-disk1 > /sys/class/leds/wdmcex2u\:hdd1\:red/trigger
fi
if [ -e /sys/class/leds/wdmcex2u\:hdd2\:red/trigger ]; then
echo ide-disk2 > /sys/class/leds/wdmcex2u\:hdd2\:red/trigger
fi
================
WD EX2 Ultra - ext3 usb kernel/rootfs, 6.6.2-mvebu/Debian/OMV, realtek-r8152 2.5GbE
Uboot - u-boot-a38x-RangerPeak_2014T3_PQ-nand_1G
Kernel Patch - mvneta.patch, linux-6.6.2-mvebu-tld-1
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition March 19, 2024 06:07AM |
Registered: 6 years ago Posts: 50 |
Otherwise, you can exploit the new kernel patch allowing ledtrig-gpio (as discussed on https://forum.doozan.com/read.php?2,136831) and compile a dts as follow:
Edited 1 time(s). Last edit at 03/19/2024 08:38AM by CyberPK.
sata1-red-led {
//label = "wdmcmg2:red:hdd1";
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_DISK_ACTIVITY;
function-enumerator = <1>;
gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "ide-disk1";
panic-indicator;
};
sata2-red-led {
//label = "wdmcmg2:red:hdd2";
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_DISK_ACTIVITY;
function-enumerator = <2>;
gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "ide-disk2";
panic-indicator;
};
sata1-blue-led {
//label = "wdmcmg2:blue:hdd1";
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_DISK;
function-enumerator = <1>;
gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "gpio";
led-pattern = <48 0>;
};
sata2-blue-led {
//label = "wdmcmg2:blue:hdd2";
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_DISK;
function-enumerator = <2>;
gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "gpio";
led-pattern = <58 0>;
};
Edited 1 time(s). Last edit at 03/19/2024 08:38AM by CyberPK.
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 11, 2024 06:28AM |
Registered: 7 months ago Posts: 8 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 11, 2024 09:16AM |
Registered: 7 months ago Posts: 8 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 11, 2024 02:06PM |
Admin Registered: 13 years ago Posts: 18,997 |
Severuspiton99,
> guys i need help, i'm not able to use minicom
> anymore, nothing happens when i connect the nas. I
> think a herror happened when i flashed the boot
> image, cause now i cant do nothing. Please i
> really need your help
Before you flashed u-boot image, did you back up the mtds? especially mtd0? If you keep the log of what you did to flash u-boot, please post here.
If you did, you can try to unbrick using kwboot to load the backup image over serial. Here is how:
https://forum.doozan.com/read.php?3,51739,51919#msg-51919
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> guys i need help, i'm not able to use minicom
> anymore, nothing happens when i connect the nas. I
> think a herror happened when i flashed the boot
> image, cause now i cant do nothing. Please i
> really need your help
Before you flashed u-boot image, did you back up the mtds? especially mtd0? If you keep the log of what you did to flash u-boot, please post here.
If you did, you can try to unbrick using kwboot to load the backup image over serial. Here is how:
https://forum.doozan.com/read.php?3,51739,51919#msg-51919
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 12, 2024 02:52AM |
Registered: 7 months ago Posts: 8 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 12, 2024 02:54AM |
Registered: 7 months ago Posts: 8 |
i just used bubt command to flash the uimage to nand, i wanted to flash back the original uboot image to try another way, cause for some reason i couldnt enable port 1 again after i flashed patched uboot. But i picked the wrong one. after the reset, and from that moment i couldnt do anything at all
Edited 1 time(s). Last edit at 04/12/2024 03:08AM by Severuspiton99.
Edited 1 time(s). Last edit at 04/12/2024 03:08AM by Severuspiton99.
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 12, 2024 02:50PM |
Admin Registered: 13 years ago Posts: 18,997 |
Severuspiton99,
Yes, you can use the mtd0 backup for the EX2 Ultra from other box. Or use the same binary that you use for the bubt command.
If you noticed, I did not promote this thread to the first post as one of "Installation Instruction for specific boxes" section. I think it is still a work in progress. There are quite a few things that I consider unfinished. But the OP seems not want to collaborate further, so I left it as is.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
i don't think i did, it's my first time with this kinda things. Should be something with kwb extension? is the backup unique for any machine or maybe i could take the backup for the ex2 ultra from someone?
Yes, you can use the mtd0 backup for the EX2 Ultra from other box. Or use the same binary that you use for the bubt command.
Quote
i just used bubt command to flash the uimage to nand, i wanted to flash back the original uboot image to try another way, cause for some reason i couldnt enable port 1 again after i flashed patched uboot. But i picked the wrong one. after the reset, and from that moment i couldnt do anything at all
If you noticed, I did not promote this thread to the first post as one of "Installation Instruction for specific boxes" section. I think it is still a work in progress. There are quite a few things that I consider unfinished. But the OP seems not want to collaborate further, so I left it as is.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 13, 2024 01:12PM |
Registered: 7 months ago Posts: 8 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 13, 2024 02:31PM |
Admin Registered: 13 years ago Posts: 18,997 |
> Just a question: the image i used Is not in .kwv,
> like i saw in the other post. Why? Should ut be?
No matter, currently you only want to be able to try to load and run with kwboot over UART (it's a non-destructive test).
But when you flash it, it must be a flash-ready format. Sometime it is .bin, sometime it is .kwb, depending on who built the u-boot image.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> like i saw in the other post. Why? Should ut be?
No matter, currently you only want to be able to try to load and run with kwboot over UART (it's a non-destructive test).
But when you flash it, it must be a flash-ready format. Sometime it is .bin, sometime it is .kwb, depending on who built the u-boot image.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 15, 2024 02:41AM |
Registered: 7 months ago Posts: 8 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 15, 2024 01:45PM |
Admin Registered: 13 years ago Posts: 18,997 |
Severuspiton99,
> I tried but when i tried to get to kwboot nothing
> happens. What could It be?
There are a few reasons. It could be that your serial connection is wrong (which is not the case here because you've used serial console before), or the kwboot version you are using is old and cannot handshake with this box BootROM successfully.
Post what is the u-boot image (where it comes from), and also post the kwboot command that you are using, what Linux host you are running ... as much info as possible.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I tried but when i tried to get to kwboot nothing
> happens. What could It be?
There are a few reasons. It could be that your serial connection is wrong (which is not the case here because you've used serial console before), or the kwboot version you are using is old and cannot handshake with this box BootROM successfully.
Post what is the u-boot image (where it comes from), and also post the kwboot command that you are using, what Linux host you are running ... as much info as possible.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 19, 2024 06:48PM |
Registered: 7 months ago Posts: 8 |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 26, 2024 05:30AM |
Registered: 7 months ago Posts: 8 |
ok, i tried with kwboot but looks like kwboot can communicate with uart adapter but can't sent the image to uart. i used this command: kwboot -t -B 115200 /dev/ttyUSB0 -b '/home/user/Desktop/nandbin.bin' -p it's stuck on "please reboot the device"
Edited 1 time(s). Last edit at 04/26/2024 05:42AM by Severuspiton99.
Edited 1 time(s). Last edit at 04/26/2024 05:42AM by Severuspiton99.
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition April 26, 2024 01:24PM |
Admin Registered: 13 years ago Posts: 18,997 |
@Severuspiton99,
> ok, i tried with kwboot but looks like kwboot can
> communicate with uart adapter but can't sent the
> image to uart. i used this command: kwboot -t -B
> 115200 /dev/ttyUSB0 -b
> '/home/user/Desktop/nandbin.bin' -p it's stuck on
> "please reboot the device"
Try using the latest kwboot binary here:
https://forum.doozan.com/read.php?3,27280
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> ok, i tried with kwboot but looks like kwboot can
> communicate with uart adapter but can't sent the
> image to uart. i used this command: kwboot -t -B
> 115200 /dev/ttyUSB0 -b
> '/home/user/Desktop/nandbin.bin' -p it's stuck on
> "please reboot the device"
Try using the latest kwboot binary here:
https://forum.doozan.com/read.php?3,27280
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
anderson
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 10, 2024 09:49PM |
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Load WD GrandTeton Serdes Config:
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | USB3 HOST0 |
| 5 | 00 | SGMII2 |
--------------------------------
PCIe, Idx 0: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
invalid mtd device 'nand0'
Error initializing mtdparts!
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:reserve2", error -19
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'ubi:reserve2' errno=-19!
ubifsmount - mount UBIFS volume
Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume
UBIFS not mounted, use ubifs mount to mount volume first!
ubifsload - load file from an UBIFS filesystem
Usage:
ubifsload <addr> <filename> [bytes]
- load file 'filename' to address 'addr'
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
## Error: "set_bootargs_debian" not defined
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
BUG: failure at xhci-mem.c:62/xhci_inval_cache()!
BUG!
-------------------------------------------------------------
PRINTENV
Hit any key to stop autoboot: 0
Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
autoload=no
baudrate=115200
boot_debi=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_debian_usb1=usb start; sleep 5
boot_debian_usb2=ext2load usb 0:1 0x00800000 /boot/uImage
boot_debian_usb3=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_debian_usb4=bootm 0x00800000 0x02100000
boot_debib3=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
bootargs=console=ttyS0,115200 root=/dev/sda1 $(mtdparts) earlyprintk=serial init=/bin/systemd
bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_el
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=run set_bootargs_debian; run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4; reset
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serve;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvN;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootcmd_nand=nand read 0x800000 0x000000 0x500000; nand read 0xA00000 0x500000 0x500000; nand read 0xC00000 0xFA00000 0xF00000; bootm 0xA00000 0xC00000
bootcmd_usb=run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4
bootdelay=1
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=00:50:43:3e:2a:22
eth1mtu=1500
eth2addr=00:50:43:3e:cd:22
eth2mtu=1500
eth3addr=00:50:43:2a:cd:3e
eth3mtu=1500
ethact=egiga2
ethaddr=00:50:43:cd:2a:22
ethmtu=1500
ethprime=egiga2
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x-modular.dtb
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.11.110
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=nand0:5m(U-Boot),5m(uImage),5m(uRamdisk),185m(image.cfs),15m(rescue_fw),20m(config),10m(reserve1),10m(reserve2)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:22:cd:3e
nandEcc=nfcConfig=4bitecc
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=RC
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
serverip=192.168.11.114
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usbActive=1
usbType=3
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3740/524284 bytes
Marvell>>
================
its possible resize MTD to fit linux-6.4.11-mvebu-tld-1-bodhi com uInitrd with 13mb?
thanks in advance
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Load WD GrandTeton Serdes Config:
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | USB3 HOST0 |
| 5 | 00 | SGMII2 |
--------------------------------
PCIe, Idx 0: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
invalid mtd device 'nand0'
Error initializing mtdparts!
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:reserve2", error -19
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'ubi:reserve2' errno=-19!
ubifsmount - mount UBIFS volume
Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume
UBIFS not mounted, use ubifs mount to mount volume first!
ubifsload - load file from an UBIFS filesystem
Usage:
ubifsload <addr> <filename> [bytes]
- load file 'filename' to address 'addr'
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
## Error: "set_bootargs_debian" not defined
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
BUG: failure at xhci-mem.c:62/xhci_inval_cache()!
BUG!
-------------------------------------------------------------
PRINTENV
Hit any key to stop autoboot: 0
Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
autoload=no
baudrate=115200
boot_debi=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_debian_usb1=usb start; sleep 5
boot_debian_usb2=ext2load usb 0:1 0x00800000 /boot/uImage
boot_debian_usb3=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_debian_usb4=bootm 0x00800000 0x02100000
boot_debib3=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
bootargs=console=ttyS0,115200 root=/dev/sda1 $(mtdparts) earlyprintk=serial init=/bin/systemd
bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_el
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=run set_bootargs_debian; run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4; reset
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serve;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvN;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootcmd_nand=nand read 0x800000 0x000000 0x500000; nand read 0xA00000 0x500000 0x500000; nand read 0xC00000 0xFA00000 0xF00000; bootm 0xA00000 0xC00000
bootcmd_usb=run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4
bootdelay=1
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=00:50:43:3e:2a:22
eth1mtu=1500
eth2addr=00:50:43:3e:cd:22
eth2mtu=1500
eth3addr=00:50:43:2a:cd:3e
eth3mtu=1500
ethact=egiga2
ethaddr=00:50:43:cd:2a:22
ethmtu=1500
ethprime=egiga2
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x-modular.dtb
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.11.110
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=nand0:5m(U-Boot),5m(uImage),5m(uRamdisk),185m(image.cfs),15m(rescue_fw),20m(config),10m(reserve1),10m(reserve2)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:22:cd:3e
nandEcc=nfcConfig=4bitecc
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=RC
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
serverip=192.168.11.114
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usbActive=1
usbType=3
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3740/524284 bytes
Marvell>>
================
its possible resize MTD to fit linux-6.4.11-mvebu-tld-1-bodhi com uInitrd with 13mb?
thanks in advance
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 10, 2024 10:47PM |
Admin Registered: 13 years ago Posts: 18,997 |
anderson,
> its possible resize MTD to fit
> linux-6.4.11-mvebu-tld-1-bodhi com uInitrd with
> 13mb?
You did not post the entire boot log. So are you able to boot to USB rootfs or SATA rootfs with the current envs?
Now it seems you want to put the kernel uImage and uInitrd on NAND mtd?
The short answer is yes, given you can already boot the kernel from USB drive, it is possible to repartition the MTDs so that there is enough room for 13MB uInitrd. But after you've done that, you will not be able to boot stock firmware again.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> its possible resize MTD to fit
> linux-6.4.11-mvebu-tld-1-bodhi com uInitrd with
> 13mb?
You did not post the entire boot log. So are you able to boot to USB rootfs or SATA rootfs with the current envs?
Now it seems you want to put the kernel uImage and uInitrd on NAND mtd?
The short answer is yes, given you can already boot the kernel from USB drive, it is possible to repartition the MTDs so that there is enough room for 13MB uInitrd. But after you've done that, you will not be able to boot stock firmware again.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Anderson
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 11, 2024 06:57PM |
Hi bodhi,
Thank you for the response. Here's what happened: with this guide (tutorial), I managed to make the EX2 work with the kernel linux-6.4.11-mvebu-tld-1-bodhi.tar.bz2.
I installed Open Media Vault 6.
Now, I want to move the uImage and uInitrd to the NAND.
I successfully transferred the uImage, which is 5MB, to the flash.
However, the uInitrd doesn't fit in the standard partition because it's also 5MB and the file doesn't fit (I tried to reduce it with this tutorial (https://forum.doozan.com/read.php?2,135322), but the file ended up being 5.78MB).
Therefore, I want to repartition to fit this uInitrd. I tried ChatGPT, but it didn't work.
At this moment, I need:
Reconfigure uBoot to boot from USB; (I changed it using ChatGPT, and now the system no longer boots)
Repartition the NAND to fit the 13MB uInitrd (so it would be nice to allocate around 15MB or more for this partition).
All this is because I want to remove the USB stick and use the NAND to initialize the system.
I don't need to worry about the original firmware... let's just go with Debian.
Thank you once again.
Ah... I didn't include the full boot log because I changed the uBoot (with ChatGPT's guidance) and now it gives this error and restarts:
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
BUG: failure at xhci-mem.c:62/xhci_inval_cache()!
BUG!
Thank you again for your attention!
Thank you for the response. Here's what happened: with this guide (tutorial), I managed to make the EX2 work with the kernel linux-6.4.11-mvebu-tld-1-bodhi.tar.bz2.
I installed Open Media Vault 6.
Now, I want to move the uImage and uInitrd to the NAND.
I successfully transferred the uImage, which is 5MB, to the flash.
However, the uInitrd doesn't fit in the standard partition because it's also 5MB and the file doesn't fit (I tried to reduce it with this tutorial (https://forum.doozan.com/read.php?2,135322), but the file ended up being 5.78MB).
Therefore, I want to repartition to fit this uInitrd. I tried ChatGPT, but it didn't work.
At this moment, I need:
Reconfigure uBoot to boot from USB; (I changed it using ChatGPT, and now the system no longer boots)
Repartition the NAND to fit the 13MB uInitrd (so it would be nice to allocate around 15MB or more for this partition).
All this is because I want to remove the USB stick and use the NAND to initialize the system.
I don't need to worry about the original firmware... let's just go with Debian.
Thank you once again.
Ah... I didn't include the full boot log because I changed the uBoot (with ChatGPT's guidance) and now it gives this error and restarts:
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
BUG: failure at xhci-mem.c:62/xhci_inval_cache()!
BUG!
Thank you again for your attention!
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 11, 2024 09:59PM |
Admin Registered: 13 years ago Posts: 18,997 |
Anderson,
> Now, I want to move the uImage and uInitrd to the
> NAND.
OK.
> I successfully transferred the uImage, which is
> 5MB, to the flash.
> However, the uInitrd doesn't fit in the standard
> partition because it's also 5MB and the file
> doesn't fit (I tried to reduce it with this
> tutorial
> (https://forum.doozan.com/read.php?2,135322), but
> the file ended up being 5.78MB).
>
> Therefore, I want to repartition to fit this
> uInitrd. I tried ChatGPT, but it didn't work.
Big mistake! ChatGPT is pretty bad (ignorant) about these things. You're the 2nd person on this forum who soft-bricked the NAS using ChatGPT.
> At this moment, I need:
>
> Reconfigure uBoot to boot from USB; (I changed it
> using ChatGPT, and now the system no longer
> boots)
OK first thing first. We'll get you booting USB rootfs again, and then worry about repartition MTDs.
> Repartition the NAND to fit the 13MB uInitrd (so
> it would be nice to allocate around 15MB or more
> for this partition).
> All this is because I want to remove the USB stick
> and use the NAND to initialize the system.
I understood. However, I'd advocate using USB rootfs only to run the NAS, there is no downside to do that other than you would use up a USB port. If your NAS has multiple USB ports, then I'd recommend using USB rootfs and take some precaution.
> Ah... I didn't include the full boot log because I
> changed the uBoot (with ChatGPT's guidance) and
> now it gives this error and restarts:
>
> (Re)start USB...
> USB0: Port (usbActive) : 1 Interface (usbType
> = 3) : USB XHCI 1.00
> scanning bus 0 for devices... 2 USB Device(s)
> found
> scanning usb for storage devices... 1
> Storage Device(s) found
> scanning usb for ethernet devices... 0
> Ethernet Device(s) found
> BUG: failure at xhci-mem.c:62/xhci_inval_cache()!
> BUG!
OK. with serial console connected, power up the NAS, and interrupt u-boot count down, and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Now, I want to move the uImage and uInitrd to the
> NAND.
OK.
> I successfully transferred the uImage, which is
> 5MB, to the flash.
> However, the uInitrd doesn't fit in the standard
> partition because it's also 5MB and the file
> doesn't fit (I tried to reduce it with this
> tutorial
> (https://forum.doozan.com/read.php?2,135322), but
> the file ended up being 5.78MB).
>
> Therefore, I want to repartition to fit this
> uInitrd. I tried ChatGPT, but it didn't work.
Big mistake! ChatGPT is pretty bad (ignorant) about these things. You're the 2nd person on this forum who soft-bricked the NAS using ChatGPT.
> At this moment, I need:
>
> Reconfigure uBoot to boot from USB; (I changed it
> using ChatGPT, and now the system no longer
> boots)
OK first thing first. We'll get you booting USB rootfs again, and then worry about repartition MTDs.
> Repartition the NAND to fit the 13MB uInitrd (so
> it would be nice to allocate around 15MB or more
> for this partition).
> All this is because I want to remove the USB stick
> and use the NAND to initialize the system.
I understood. However, I'd advocate using USB rootfs only to run the NAS, there is no downside to do that other than you would use up a USB port. If your NAS has multiple USB ports, then I'd recommend using USB rootfs and take some precaution.
> Ah... I didn't include the full boot log because I
> changed the uBoot (with ChatGPT's guidance) and
> now it gives this error and restarts:
>
> (Re)start USB...
> USB0: Port (usbActive) : 1 Interface (usbType
> = 3) : USB XHCI 1.00
> scanning bus 0 for devices... 2 USB Device(s)
> found
> scanning usb for storage devices... 1
> Storage Device(s) found
> scanning usb for ethernet devices... 0
> Ethernet Device(s) found
> BUG: failure at xhci-mem.c:62/xhci_inval_cache()!
> BUG!
OK. with serial console connected, power up the NAS, and interrupt u-boot count down, and
printenv bootAnd post the entire serial console log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Anderson
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 12, 2024 07:14AM |
---------------------
STARTUP
---------------------
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Load WD GrandTeton Serdes Config:
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | USB3 HOST0 |
| 5 | 00 | SGMII2 |
--------------------------------
PCIe, Idx 0: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
invalid mtd device 'nand0'
Error initializing mtdparts!
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:reserve2", error -19
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'ubi:reserve2' errno=-19!
ubifsmount - mount UBIFS volume
Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume
UBIFS not mounted, use ubifs mount to mount volume first!
ubifsload - load file from an UBIFS filesystem
Usage:
ubifsload <addr> <filename> [bytes]
- load file 'filename' to address 'addr'
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
--------------------------------
PRINTENV
--------------------------------
Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
autoload=no
baudrate=115200
boot_debi=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_debian_usb1=usb start; sleep 5
boot_debian_usb2=ext2load usb 0:1 0x00800000 /boot/uImage
boot_debian_usb3=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_debian_usb4=bootm 0x00800000 0x02100000
boot_debib3=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
bootargs=console=ttyS0,115200 root=/dev/sda1 $(mtdparts) earlyprintk=serial init=/bin/systemd
bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:ll
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=run set_bootargs_debian; run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4; reset
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootcmd_nand=nand read 0x800000 0x000000 0x500000; nand read 0xA00000 0x500000 0x500000; nand read 0xC00000 0xFA00000 0xF00000; bootm 0xA00000 0xC0
bootcmd_usb=run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4
bootdelay=1
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=00:50:43:3e:2a:22
eth1mtu=1500
eth2addr=00:50:43:3e:cd:22
eth2mtu=1500
eth3addr=00:50:43:2a:cd:3e
eth3mtu=1500
ethact=egiga2
ethaddr=00:50:43:cd:2a:22
ethmtu=1500
ethprime=egiga2
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x-modular.dtb
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.11.110
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=nand0:5m(U-Boot),5m(uImage),5m(uRamdisk),185m(image.cfs),15m(rescue_fw),20m(config),10m(reserve1),10m(reserve2)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:22:cd:3e
nandEcc=nfcConfig=4bitecc
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=RC
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
serverip=192.168.11.114
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; boot;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usbActive=1
usbType=3
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3740/524284 bytes
Marvell>>
---------------------
BOOT
---------------------
Marvell>> boot
## Error: "set_bootargs_debian" not defined
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
## Booting image at 00800000 ...
NAND read: device 0 offset 0xc800800, size 0xf00000
15728640 bytes read: OK
## Booting image at 00a00000 ...
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...
go to begin.....
STARTUP
---------------------
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Load WD GrandTeton Serdes Config:
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | USB3 HOST0 |
| 5 | 00 | SGMII2 |
--------------------------------
PCIe, Idx 0: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
invalid mtd device 'nand0'
Error initializing mtdparts!
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:reserve2", error -19
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'ubi:reserve2' errno=-19!
ubifsmount - mount UBIFS volume
Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume
UBIFS not mounted, use ubifs mount to mount volume first!
ubifsload - load file from an UBIFS filesystem
Usage:
ubifsload <addr> <filename> [bytes]
- load file 'filename' to address 'addr'
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
--------------------------------
PRINTENV
--------------------------------
Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
autoload=no
baudrate=115200
boot_debi=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_debian_usb1=usb start; sleep 5
boot_debian_usb2=ext2load usb 0:1 0x00800000 /boot/uImage
boot_debian_usb3=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_debian_usb4=bootm 0x00800000 0x02100000
boot_debib3=ext2load usb 0:1 0x02100000 /boot/uInitrd
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
bootargs=console=ttyS0,115200 root=/dev/sda1 $(mtdparts) earlyprintk=serial init=/bin/systemd
bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:ll
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=run set_bootargs_debian; run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4; reset
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootcmd_nand=nand read 0x800000 0x000000 0x500000; nand read 0xA00000 0x500000 0x500000; nand read 0xC00000 0xFA00000 0xF00000; bootm 0xA00000 0xC0
bootcmd_usb=run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4
bootdelay=1
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=00:50:43:3e:2a:22
eth1mtu=1500
eth2addr=00:50:43:3e:cd:22
eth2mtu=1500
eth3addr=00:50:43:2a:cd:3e
eth3mtu=1500
ethact=egiga2
ethaddr=00:50:43:cd:2a:22
ethmtu=1500
ethprime=egiga2
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x-modular.dtb
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.11.110
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=nand0:5m(U-Boot),5m(uImage),5m(uRamdisk),185m(image.cfs),15m(rescue_fw),20m(config),10m(reserve1),10m(reserve2)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:22:cd:3e
nandEcc=nfcConfig=4bitecc
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=RC
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
serverip=192.168.11.114
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; boot;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usbActive=1
usbType=3
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3740/524284 bytes
Marvell>>
---------------------
BOOT
---------------------
Marvell>> boot
## Error: "set_bootargs_debian" not defined
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
## Booting image at 00800000 ...
NAND read: device 0 offset 0xc800800, size 0xf00000
15728640 bytes read: OK
## Booting image at 00a00000 ...
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...
go to begin.....
|
Anderson
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 12, 2024 10:10AM |
by the way:
this printenv show the variables thats works:
this printenv show the variables thats works:
printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_debian_usb1=usb start; sleep 5 boot_debian_usb2=ext2load usb 0:1 0x00800000 /boot/uImage boot_debian_usb3=ext2load usb 0:1 0x02100000 /boot/uInitrd boot_debian_usb4=bootm 0x00800000 0x02100000 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovl bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=run set_bootargs_debian; run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4; reset bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$ser; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$i; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=1 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:22:30:11 eth1mtu=1500 eth2addr=00:50:43:22:b4:11 eth2mtu=1500 eth3addr=00:50:43:30:b4:22 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:b4:30:11 ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(r) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:11:b4:22 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 set_bootargs_debian='setenv bootargs console=ttyS0,115200 root=/dev/sda1 $(mtdparts) earlyprintk=serial init=/bin/systemd standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end;; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3555/524284 bytes
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 12, 2024 02:41PM |
Admin Registered: 13 years ago Posts: 18,997 |
Anderson,
Power up, interrupt u-boot at count down and,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Power up, interrupt u-boot at count down and,
setenv usbActive 0 setenv set_bootargs_debian 'setenv bootargs console=ttyS0,115200 root=/dev/sda1 $(mtdparts) earlyprintk=serial init=/bin/systemd' setenv bootcmd 'run set_bootargs_debian; run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4; reset'And then
boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Anderson
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 13, 2024 09:24PM |
Marvell>> setenv usbActive 0 Marvell>> setenv set_bootargs_debian 'setenv bootargs console=ttyS0,115200 root=/dev/sdb1 $(mtdparts) earlyprintk=serial init=/bin/system' Marvell>> setenv bootcmd 'run set_bootargs_debian; run boot_debian_usb1; run boot_debian_usb2; run boot_debian_usb3; run boot_debian_usb4' Marvell>> boot
I changed sda1 to sdb1, because rootfs usb is sdb1
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
5138476 bytes read in 498 ms (9.8 MiB/s)
6019564 bytes read in 545 ms (10.5 MiB/s)
## Booting image at 00800000 ...
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-6.4.11-mvebu-tld-1
Created: 2023-12-01 13:38:32 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5138412 Bytes = 4.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initrd.img-6.4.11-mvebu-tld-1
Created: 2024-07-11 1:17:59 UTC
Image Type: ARM Linux RAMDisk Image (lzma compressed)
Data Size: 6019500 Bytes = 5.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.4.11-mvebu-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian)3
[ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Ex2 Ultra
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] percpu: Embedded 14 pages/cpu s25300 r8192 d23852 u57344
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sdb1 $(mtdparts) earlyprintk=serial init=/bin/systemd
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260416
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1013736K/1048576K available (10240K kernel code, 867K rwdata, 3444K rodata, 1024K init, 462K bss, 34840K r)
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000001][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.008681][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
[ 0.020389][ T0] Switching to timer-based delay loop, resolution 1ns
[ 0.027213][ T0] Ignoring duplicate/late registration of read_current_timer delay
[ 0.034930][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.046797][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval)
[ 0.056733][ T0] Console: colour dummy device 80x30
[ 0.061889][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000)
[ 0.073167][ T0] CPU: Testing write buffer coherency: ok
[ 0.078754][ T0] CPU0: Spectre v2: using BPIALL workaround
[ 0.084479][ T0] pid_max: default: 32768 minimum: 301
[ 0.090026][ T0] LSM: initializing lsm=capability,integrity
[ 0.095982][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.103970][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.113477][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.120608][ T1] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.128521][ T1] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.135356][ T1] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.143261][ T1] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.150143][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.157127][ T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.163058][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.170030][ T1] rcu: Hierarchical SRCU implementation.
[ 0.175497][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.182123][ T1] smp: Bringing up secondary CPUs ...
[ 0.187876][ T1] Booting CPU 1
[ 0.191343][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.191354][ T0] CPU1: Spectre v2: using BPIALL workaround
[ 0.203496][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.208297][ T1] SMP: Total of 2 processors activated (2664.00 BogoMIPS).
[ 0.215322][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.221024][ T1] devtmpfs: initialized
[ 0.229118][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.237702][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.248218][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.255903][ T1] prandom: seed boundary self test passed
[ 0.263058][ T1] prandom: 100 self tests passed
[ 0.267839][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.274819][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.282137][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.290467][ T1] audit: initializing netlink subsys (disabled)
[ 0.296711][ T25] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1
[ 0.297147][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.305165][ T1] cpuidle: using governor ladder
[ 0.316645][ T1] cpuidle: using governor menu
[ 0.321395][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.330076][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.336733][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.345514][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.355451][ T1] platform soc: Fixed dependency cycle(s) with /soc/internal-regs/interrupt-controller@d000
[ 0.537110][ T1] raid6: int32x8 gen() 266 MB/s
[ 0.707141][ T1] raid6: int32x4 gen() 277 MB/s
[ 0.877110][ T1] raid6: int32x2 gen() 459 MB/s
[ 1.047087][ T1] raid6: int32x1 gen() 533 MB/s
[ 1.052034][ T1] raid6: using algorithm int32x1 gen() 533 MB/s
[ 1.227095][ T1] raid6: .... xor() 205 MB/s, rmw enabled
[ 1.232649][ T1] raid6: using intx1 recovery algorithm
[ 1.238881][ T1] SCSI subsystem initialized
[ 1.243598][ T1] usbcore: registered new interface driver usbfs
[ 1.249825][ T1] usbcore: registered new interface driver hub
[ 1.255837][ T1] usbcore: registered new device driver usb
[ 1.261827][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.267482][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.277303][ T1] PTP clock support registered
[ 1.283255][ T1] vgaarb: loaded
[ 1.287040][ T1] clocksource: Switched to clocksource arm_global_timer
[ 1.294299][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.298993][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.314026][ T1] NET: Registered PF_INET protocol family
[ 1.319777][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.329268][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 1.338418][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.346841][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.355336][ T1] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 1.363376][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.370592][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 1.378723][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.386027][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.393911][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.400716][ T1] RPC: Registered named UNIX socket transport module.
[ 1.407353][ T1] RPC: Registered udp transport module.
[ 1.412733][ T1] RPC: Registered tcp transport module.
[ 1.418121][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.425237][ T1] PCI: CLS 0 bytes, default 64
[ 1.430040][ T35] Trying to unpack rootfs image as initramfs...
[ 1.436156][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 1.447359][ T1] Initialise system trusted keyrings
[ 1.452556][ T1] Key type blacklist registered
[ 1.457454][ T1] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 1.464718][ T1] zbud: loaded
[ 1.469273][ T1] NFS: Registering the id_resolver key type
[ 1.475021][ T1] Key type id_resolver registered
[ 1.479938][ T1] Key type id_legacy registered
[ 1.484662][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.492054][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.556133][ T1] xor: measuring software checksum speed
[ 1.566170][ T1] arm4regs : 2172 MB/sec
[ 1.577140][ T1] 8regs : 1669 MB/sec
[ 1.587860][ T1] 32regs : 1732 MB/sec
[ 1.592894][ T1] xor: using function: arm4regs (2172 MB/sec)
[ 1.598807][ T1] async_tx: api initialized (async)
[ 1.603845][ T1] Key type asymmetric registered
[ 1.608627][ T1] Asymmetric key parser 'x509' registered
[ 1.614392][ T1] bounce: pool size: 64 pages
[ 1.619200][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 1.627384][ T1] io scheduler bfq registered
[ 1.634999][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 1.644375][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 1.654483][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present!
[ 1.663597][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 1.673641][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present!
[ 1.684109][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 1.747762][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 1.758481][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 1.827786][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 1.911471][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.920395][ T1] printk: console [ttyS0] disabled
[ 1.945613][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 39, base_baud = 12500000) is a 16550A
[ 1.955306][ T1] printk: console [ttyS0] enabled
[ 1.955306][ T1] printk: console [ttyS0] enabled
[ 1.965141][ T1] printk: bootconsole [earlycon0] disabled
[ 1.965141][ T1] printk: bootconsole [earlycon0] disabled
[ 2.018159][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 40, base_baud = 12500000) is a 16550A
[ 2.029190][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
[ 2.037739][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
[ 2.046049][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
[ 2.054728][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 2.064566][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 2.075110][ T1] scsi host0: ahci-mvebu
[ 2.079878][ T1] scsi host1: ahci-mvebu
[ 2.084236][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
[ 2.092951][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
[ 2.102822][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 2.109957][ T1] nand: Macronix MX30LF2G18AC
[ 2.114570][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.123227][ T1] Bad block table found at page 131008, version 0x01
[ 2.130129][ T1] Bad block table found at page 130944, version 0x01
[ 2.136862][ T1] nand_read_bbt: bad block at 0x0000080c0000
[ 2.142819][ T1] 8 fixed-partitions partitions found on MTD device pxa3xx_nand-0
[ 2.150548][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0":
[ 2.156680][ T1] 0x000000000000-0x000000500000 : "U-Boot"
[ 2.163822][ T1] 0x000000500000-0x000000a00000 : "uImage"
[ 2.170829][ T1] 0x000000a00000-0x000000f00000 : "uRamdisk"
[ 2.178004][ T1] 0x000000f00000-0x00000c800000 : "image.cfs"
[ 2.185535][ T1] 0x00000c800000-0x00000d700000 : "rescue fw"
[ 2.192862][ T1] 0x00000d700000-0x00000eb00000 : "config"
[ 2.199986][ T1] 0x00000eb00000-0x00000f500000 : "reserve1"
[ 2.207240][ T1] 0x00000f500000-0x00000ff00000 : "reserve2"
[ 2.214938][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 2.223559][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 2.428494][ T664] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.597078][ T659] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.604549][ T659] ata1.00: ATA-9: WDC WD5000LPCX-24C6HT0, 02.01A02, max UDMA/133
[ 2.612191][ T659] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 32)
[ 2.619937][ T659] ata1.00: configured for UDMA/133
[ 2.625313][ T220] scsi 0:0:0:0: Direct-Access ATA WDC WD5000LPCX-2 1A02 PQ: 0 ANSI: 5
[ 2.641503][ T11] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 2.657072][ T11] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.667084][ T11] sd 0:0:0:0: [sda] Write Protect is off
[ 2.672698][ T11] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.682612][ T11] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[ 4.201516][ T35] Freeing initrd memory: 5880K
[ 4.269086][ T1] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 4.278357][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 4.291630][ T1] mvneta f1034000.ethernet eth0: Using random mac address 26:b3:25:9b:0c:59
[ 4.300825][ T1] usbcore: registered new interface driver smsc75xx
[ 4.307640][ T1] orion-ehci f1058000.usb: EHCI Host Controller
[ 4.313790][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 4.322290][ T1] orion-ehci f1058000.usb: irq 44, io mem 0xf1058000
[ 4.357052][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 4.363911][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.04
[ 4.372946][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.380926][ T1] usb usb1: Product: EHCI Host Controller
[ 4.386532][ T1] usb usb1: Manufacturer: Linux 6.4.11-mvebu-tld-1 ehci_hcd
[ 4.393717][ T1] usb usb1: SerialNumber: f1058000.usb
[ 4.399567][ T1] hub 1-0:1.0: USB hub found
[ 4.404066][ T1] hub 1-0:1.0: 1 port detected
[ 4.409897][ T1] usbcore: registered new interface driver usblp
[ 4.416164][ T1] usbcore: registered new interface driver usb-storage
[ 4.423234][ T1] mousedev: PS/2 mouse device common for all mice
[ 4.430733][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 4.437276][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2024-07-14T01:51:21 UTC (1720921881)
[ 4.447624][ T1] i2c_dev: i2c /dev entries driver
[ 4.452814][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported
[ 4.461699][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported
[ 4.473003][ T1] orion_wdt: Initial timeout 171 sec
[ 4.478804][ T1] device-mapper: uevent: version 1.0.3
[ 4.484330][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 4.493807][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 4.501094][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 4.508478][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 4.513618][ T11] sda: sda1 sda2
[ 4.515874][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 4.526403][ T1] sdhci: Secure Digital Host Controller Interface driver
[ 4.526783][ T11] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.533355][ T1] sdhci: Copyright(c) Pierre Ossman
[ 4.544790][ T1] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.553441][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 4.561562][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 4.567665][ T1] usbcore: registered new interface driver usbhid
[ 4.573973][ T1] usbhid: USB HID core driver
[ 4.579304][ T1] NET: Registered PF_INET6 protocol family
[ 4.586027][ T1] Segment Routing with IPv6
[ 4.590486][ T1] RPL Segment Routing with IPv6
[ 4.595257][ T1] In-situ OAM (IOAM) with IPv6
[ 4.600006][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 4.607849][ T1] NET: Registered PF_PACKET protocol family
[ 4.613785][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 4.618779][ T1] Key type dns_resolver registered
[ 4.623959][ T1] ThumbEE CPU extension supported.
[ 4.628977][ T1] Registering SWP/SWPB emulation handler
[ 4.666515][ T1] registered taskstats version 1
[ 4.671489][ T1] Loading compiled-in X.509 certificates
[ 4.678681][ T1] Key type .fscrypt registered
[ 4.683334][ T1] Key type fscrypt-provisioning registered
[ 4.689137][ T1] Key type big_key registered
[ 4.709943][ T1] Key type encrypted registered
[ 4.717813][ T11] usb_phy_generic usb3_0_phy: dummy supplies not allowed for exclusive requests
[ 4.726998][ T11] usb_phy_generic usb3_1_phy: dummy supplies not allowed for exclusive requests
[ 4.736333][ T11] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 4.742415][ T11] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 4.750725][ T11] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 4.760801][ T11] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000
[ 4.767446][ T11] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 4.773498][ T11] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 4.781760][ T11] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 4.789011][ T11] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.04
[ 4.798041][ T11] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.806005][ T11] usb usb2: Product: xHCI Host Controller
[ 4.811626][ T11] usb usb2: Manufacturer: Linux 6.4.11-mvebu-tld-1 xhci-hcd
[ 4.818810][ T11] usb usb2: SerialNumber: f10f0000.usb3
[ 4.824710][ T11] hub 2-0:1.0: USB hub found
[ 4.829230][ T11] hub 2-0:1.0: 1 port detected
[ 4.834221][ T11] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.843166][ T11] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.04
[ 4.852194][ T11] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.860228][ T11] usb usb3: Product: xHCI Host Controller
[ 4.865834][ T11] usb usb3: Manufacturer: Linux 6.4.11-mvebu-tld-1 xhci-hcd
[ 4.873021][ T11] usb usb3: SerialNumber: f10f0000.usb3
[ 4.878931][ T11] hub 3-0:1.0: USB hub found
[ 4.883430][ T11] hub 3-0:1.0: 1 port detected
[ 4.888668][ T11] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 4.894728][ T11] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 4.903050][ T11] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 4.913064][ T11] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000
[ 4.919717][ T11] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 4.925769][ T11] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 4.934017][ T11] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 4.941241][ T11] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.04
[ 4.950274][ T11] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.958247][ T11] usb usb4: Product: xHCI Host Controller
[ 4.963853][ T11] usb usb4: Manufacturer: Linux 6.4.11-mvebu-tld-1 xhci-hcd
[ 4.971226][ T11] usb usb4: SerialNumber: f10f8000.usb3
[ 4.977175][ T11] hub 4-0:1.0: USB hub found
[ 4.981675][ T11] hub 4-0:1.0: 1 port detected
[ 4.986650][ T11] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.995592][ T11] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.04
[ 5.004707][ T11] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.012711][ T11] usb usb5: Product: xHCI Host Controller
[ 5.018404][ T11] usb usb5: Manufacturer: Linux 6.4.11-mvebu-tld-1 xhci-hcd
[ 5.025583][ T11] usb usb5: SerialNumber: f10f8000.usb3
[ 5.031479][ T11] hub 5-0:1.0: USB hub found
[ 5.035976][ T11] hub 5-0:1.0: 1 port detected
[ 5.041699][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 5.049879][ T1] clk: Disabling unused clocks
[ 5.056785][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 5.087800][ T1] Checked W+X mappings: passed, no W+X pages found
[ 5.094244][ T1] Run /init as init process
[ 5.117090][ T101] usb 2-1: new high-speed USB device number 2 using xhci-hcd
Loading, please wait...
Starting version 247.3-7+deb11u5
[ 5.297585][ T101] usb 2-1: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00
[ 5.306528][ T101] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.322660][ T101] usb 2-1: Product: Cruzer Fit
[ 5.330421][ T101] usb 2-1: Manufacturer: SanDisk'
[ 5.335338][ T101] usb 2-1: SerialNumber: 4C530000070407214094
[ 5.349135][ T101] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 5.388147][ T101] scsi host2: usb-storage 2-1:1.0
[ 5.437361][ T1274] usbcore: registered new interface driver uas
[ 5.685932][ T1282] mtdblock: MTD device 'U-Boot' is NAND, please consider using UBI block devices instead.
[ 5.699358][ T1276] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead.
[ 5.704450][ T1273] mtdblock: MTD device 'rescue fw' is NAND, please consider using UBI block devices instead.
[ 5.713316][ T1278] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead.
[ 5.730020][ T1280] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead.
[ 5.739433][ T1276] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead.
[ 5.745062][ T1281] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead.
[ 5.761716][ T1282] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead.
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems
[ 6.356863][ T1313] mtdblock: MTD device 'U-Boot' is NAND, please consider using UBI block devices instead.
[ 6.379226][ T1313] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead.
[ 6.399870][ T1313] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead.
[ 6.421445][ T1313] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead.
[ 6.438450][ T11] scsi 2:0:0:0: Direct-Access SanDisk' Cruzer Fit 1.00 PQ: 0 ANSI: 6
[ 6.460035][ T35] sd 2:0:0:0: [sdb] 60088320 512-byte logical blocks: (30.8 GB/28.7 GiB)
[ 6.469584][ T35] sd 2:0:0:0: [sdb] Write Protect is off
[ 6.475384][ T35] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 6.489501][ T35] sdb: sdb1
[ 6.492974][ T35] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 6.546848][ T1313] mtdblock: MTD device 'rescue fw' is NAND, please consider using UBI block devices instead.
[ 6.589343][ T1313] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead.
[ 6.630645][ T1313] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead.
[ 6.672201][ T1313] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead.
done.
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext4 (1) -- /dev/sdb1] fsck.ext4 -a -C0 /dev/sdb1
rootfs: clean, 117029/1880480 files, 2574571/7510784 blocks
done.
[ 7.137989][ T1326] EXT4-fs (sdb1): mounted filesystem 17e47247-3d39-425b-8652-cfddfdd86fbf ro with ordered data mode. Quota mode: non.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 8.072592][ T1] systemd[1]: systemd 247.3-7+deb11u5 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT )
[ 8.098648][ T1] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
[ 8.158771][ T1] systemd[1]: Set hostname to <lua>.
[ 8.223932][ T1] systemd[1]: Using hardware watchdog 'Orion Watchdog', version 0, device /dev/watchdog
[ 8.233659][ T1] systemd[1]: Set hardware watchdog to 15s.
[ 10.677649][ T1286] random: crng init done
[ 11.224827][ T1] systemd[1]: /lib/systemd/system/minidlna.service:4: Failed to add dependency on autofs, ignoring: Invalid argument
[ 11.315002][ T1] systemd[1]: Queued start job for default target Graphical Interface.
[ 11.500293][ T1] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 11.538809][ T1] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 11.578643][ T1] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 11.628645][ T1] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ 11.668389][ T1] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 11.707425][ T1] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 11.747404][ T1] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 11.787842][ T1] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ OK ] Set up automount Arbitrary…s File System Automount Point.
[ 11.827340][ T1] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 11.867439][ T1] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 11.897273][ T1] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 11.927299][ T1] systemd[1]: Reached target System Time Set.
[ OK ] Reached target System Time Set.
[ 11.967487][ T1] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ OK ] Listening on Device-mapper event daemon FIFOs.
[ 12.007593][ T1] systemd[1]: Listening on LVM2 poll daemon socket.
[ OK ] Listening on LVM2 poll daemon socket.
[ 12.150091][ T1] systemd[1]: Listening on RPCbind Server Activation Socket.
[ OK ] Listening on RPCbind Server Activation Socket.
[ 12.200032][ T1] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 12.237649][ T1] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 12.277395][ T1] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 12.317772][ T1] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 12.357559][ T1] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 12.397691][ T1] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 12.437725][ T1] systemd[1]: Listening on Network Service Netlink Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ 12.477694][ T1] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 12.517549][ T1] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 12.557677][ T1] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 12.667493][ T1] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 12.711278][ T1] systemd[1]: Mounting RPC Pipe File System...
Mounting RPC Pipe File System...
[ 12.751471][ T1] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 12.787566][ T1] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[ 12.797025][ T1] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[ 12.807569][ T1] systemd[1]: Finished Availability of block devices.
[ OK ] Finished Availability of block devices.
[ 12.927782][ T1] systemd[1]: Starting Create list of static device nodes for the current kernel...
Starting Create list of st…odes for the current kernel...
[ 12.971780][ T1] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
Starting Monitoring of LVM…meventd or progress polling...
[ 13.021374][ T1] systemd[1]: Starting Load Kernel Module configfs...
Starting Load Kernel Module configfs...
[ 13.061437][ T1] systemd[1]: Starting Load Kernel Module drm...
Starting Load Kernel Module drm...
[ 13.102319][ T1] systemd[1]: Starting Load Kernel Module fuse...
Starting Load Kernel Module fuse...
[ 13.143392][ T1375] fuse: init (API version 7.38)
[ 13.148391][ T1] systemd[1]: Condition check resulted in OpenVSwitch configuration for cleanup being skipped.
[ 13.168550][ T1] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 13.178924][ T1] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 13.277866][ T1] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 13.325142][ T1] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 13.362454][ T1] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 13.387466][ T1377] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
[ 13.396665][ T1377] softdog: soft_reboot_cmd=<not set> soft_active_on_boot=0
[ 13.455281][ T1379] EXT4-fs (sdb1): re-mounted 17e47247-3d39-425b-8652-cfddfdd86fbf r/w. Quota mode: none.
[ 13.468437][ T1] systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
[ 13.517731][ T1] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted RPC Pipe File System.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Finished Create list of st… nodes for the current kernel.
[ OK ] Finished Monitoring of LVM… dmeventd or progress polling.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module fuse.
[ OK ] Finished Load Kernel Modules.
[ OK ] Finished Remount Root and Kernel File Systems.
Activating swap /swapfile1...
[ 13.955692][ T1384] Adding 2047996k swap on /swapfile1. Priority:-2 extents:47 across:16285692k FS
Mounting FUSE Control File System...
Mounting Kernel Configuration File System...
Starting pNFS block layout mapping daemon...
[ 14.035205][ T1388] mtdblock: MTD device 'U-Boot' is NAND, please consider using UBI block devices instead.
[ 14.045664][ T1388] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead.
[ 14.055654][ T1388] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead.
[ 14.066331][ T1388] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead.
[ 14.076986][ T1388] mtdblock: MTD device 'rescue fw' is NAND, please consider using UBI block devices instead.
[ 14.088352][ T1388] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead.
[ 14.098348][ T1388] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead.
[ 14.108489][ T1388] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead.
Starting Flush Journal to Persistent Storage...
Starting Load/Save Random Seed[ 14.185928][ T1376] systemd-journald[1376]: Received client request to flush runtime journal.
...
Starting Apply Kernel Variables...
Starting Create System Users...
[ OK ] Activated swap /swapfile1.
[ OK ] Finished Coldplug All udev Devices.
[ OK ] Mounted FUSE Control File System.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started pNFS block layout mapping daemon.
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished Apply Kernel Variables.
[ OK ] Reached target Swap.
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Finished Create System Users.
[ OK ] Finished Helper to synchronize boot up for ifupdown.
Starting Create Static Device Nodes in /dev...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
Mounting Mount /tmp as tmp…e access to the root device...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Mounted Mount /tmp as tmpf…ite access to the root device.
[ OK ] Reached target Local File Systems.
Starting Raise network interfaces...
Starting Preprocess NFS configuration...
Starting Cleanup monit state file...
Starting Cleanup PHP session files...
[ OK ] Finished Preprocess NFS configuration.
[ OK ] Reached target NFS client services.
[ OK ] Finished Cleanup monit state file.
[ OK ] Finished Cleanup PHP session files.
[ OK ] Started Rule-based Manager for Device Events and Files.
Starting Network Service...
[ OK ] Found device /dev/ttyS0.
[ 16.585215][ T1418] mtdblock: MTD device 'U-Boot' is NAND, please consider using UBI block devices instead.
[ 16.597299][ T1416] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead.
[ 16.636504][ T1413] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead.
[ 16.654856][ T1421] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead.
[ 16.662714][ T1418] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead.
[ 16.699670][ T1421] mtdblock: MTD device 'rescue fw' is NAND, please consider using UBI block devices instead.
[ 16.754201][ T1415] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead.
[ 16.766498][ T1414] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead.
[ 16.914083][ T1412] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 16.922203][ T1412] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ OK ] Started Network Service.
Starting Wait for Network to be Configured...
[ 17.309098][ T1422] mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL)
[ 17.325670][ T1422] mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode
[ OK ] Finished Raise network interfaces.
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Found device WDC_WD5000LPCX-24C6HT0 2.
Starting File System Check…e897-439c-9f47-f273c69262d5...
Starting Create Volatile Files and Directories...
[ OK ] Started File System Check Daemon to report status.
[ OK ] Finished Create Volatile Files and Directories.
Starting RPC bind portmap service...
Starting Network Name Resolution...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started RPC bind portmap service.
[ OK ] Reached target Remote File Systems (Pre).
[ OK ] Reached target RPC Port Mapper.
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
Starting Docker Socket for the API.
[ OK ] Listening on Podman API Socket.
[ OK ] Listening on Docker Socket for the API.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Avahi mDNS/DNS-SD Stack...
[ OK ] Started D-Bus System Message Bus.
Starting Remove Stale Onli…t4 Metadata Check Snapshots...
Starting Initialize hardware monitoring sensors...
Starting System Logging Service...
Starting User Login Management...
Starting WPA supplicant...
[ OK ] Finished File System Check…8-e897-439c-9f47-f273c69262d5.
Mounting /srv/dev-disk-by-…e897-439c-9f47-f273c69262d5...
[ 19.723981][ T1569] EXT4-fs (sda2): mounted filesystem 0b2d64f8-e897-439c-9f47-f273c69262d5 r/w with ordered data mode. Quota mode: jo.
[ OK ] Mounted /srv/dev-disk-by-u…8-e897-439c-9f47-f273c69262d5.
[ OK ] Finished Initialize hardware monitoring sensors.
[ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots.
[ OK ] Started System Logging Service.
[ OK ] Started User Login Management.
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started Network Name Resolution.
[ OK ] Started WPA supplicant.
[ OK ] Reached target Network.
[ OK ] Reached target Host and Network Name Lookups.
Starting chrony, an NTP client/server...
Starting containerd container runtime...
Starting Fail2Ban Service...
Starting A high performanc… and a reverse proxy server...
Starting The OpenMediaVaul…t processes the RPC request...
Starting The PHP 7.4 FastCGI Process Manager...
[ OK ] Started fast remote file copy program daemon.
Starting OpenBSD Secure Shell server...
[ OK ] Started vnStat network traffic monitor.
[ OK ] Started chrony, an NTP client/server.
[ OK ] Started Fail2Ban Service.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Trigger anacron every hour.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Discard unused blocks once a week.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily man-db regeneration.
[ OK ] Started Clean PHP session files every 30 mins.
[ OK ] Started Podman auto-update timer.
[ OK ] Reached target Timers.
[ 21.478286][ T1238] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 21.487097][ T1238] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ OK ] Started Run anacron jobs.
Starting Clean php session files...
Starting Rotate log files...
Starting Daily man-db regeneration...
[ OK ] Started OpenBSD Secure Shell server.
[ OK ] Finished Wait for Network to be Configured.
[ OK ] Reached target Network is Online.
Starting AdGuard Home: Network-level blocker...
Starting Samba NMB Daemon...
Starting Generate the prelogin message...
Starting Podman pod-filebrowser.service...
Starting Podman auto-update service...
Starting /etc/rc.local Compatibility...
[ OK ] Started Web Services Dynamic Discovery host daemon.
[ OK ] Started AdGuard Home: Network-level blocker.
[ OK ] Started A high performance…er and a reverse proxy server.
[ 23.972879] rc.local[1648]: Cannot read environment, using default
[ 24.010884] rc.local[1648]: Cannot read default environment from file
[ 24.110706] rc.local[1650]: <13>Jul 13 22:51:41 root[1650]: Cannot read u-boot env ethaddr
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started The OpenMediaVault…hat processes the RPC request.
[ OK ] Finished Clean php session files.
[ OK ] Finished Rotate log files.
[ OK ] Started The PHP 7.4 FastCGI Process Manager.
[ OK ] Started Samba NMB Daemon.
Starting Samba SMB Daemon...
[ OK ] Started Samba SMB Daemon.
[ OK ] Finished Daily man-db regeneration.
[ OK ] Started containerd container runtime.
[ OK ] Finished Podman auto-update service.
[ OK ] Created slice Virtual Machine and Container Slice.
[ OK ] Created slice cgroup machi…8264e711516a180333611c2.slice.
[ 40.769168][ T101] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 41.747216][ T6] IPv6: ADDRCONF(NETDEV_CHANGE): veth8d8e186f: link becomes ready
[ OK ] Started libcrun container.
[ OK ] Started Podman pod-filebrowser.service.
Starting Podman container-filebrowser-app.service...
[ OK ] Started libcrun container.
[ OK ] Started Podman container-filebrowser-app.service.
[ OK ] Finished Generate the prelogin message.
[ TIME ] Timed out waiting for device ??e-d3a6-419a-8320-79557232c19f.
[DEPEND] Dependency failed for /srv…e-d3a6-419a-8320-79557232c19f.
[DEPEND] Dependency failed for File…e-d3a6-419a-8320-79557232c19f.
Starting Docker Application Container Engine...
Starting File System Quota Check...
[ OK ] Finished File System Quota Check.
Starting Enable File System Quotas...
[ OK ] Finished Enable File System Quotas.
[ OK ] Reached target Remote File Systems.
Starting LSB: Starts syslogd...
[ OK ] Started Regular background program processing daemon.
Starting LSB: Load kernel …d to enable cpufreq scaling...
[ OK ] Started MiniDLNA lightweight DLNA/UPnP-AV server.
Starting LSB: service and resource monitoring daemon...
Starting LSB: start or stop rrdcached...
Starting Permit User Sessions...
[ OK ] Started LSB: Starts syslogd.
[ OK ] Finished Permit User Sessions.
Starting LSB: Starts klogd...
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Reached target Login Prompts.
[ OK ] Started LSB: Starts klogd.
[ OK ] Started LSB: service and resource monitoring daemon.
[ OK ] Started LSB: Load kernel m…ded to enable cpufreq scaling.
Starting LSB: set CPUFreq kernel parameters...
[ OK ] Started LSB: set CPUFreq kernel parameters.
[ OK ] Started LSB: start or stop rrdcached.
Starting Statistics collection and monitoring daemon...
[ OK ] Started Statistics collection and monitoring daemon.
[ 107.998764][ T2102] fbcon: Taking over console
[ 108.823083][ T2191] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter.
[ 108.844520][ T2191] Bridge firewalling registered
openmediavault 6.9.16-1 (Shaitan) lua ttyS0
Copyright (C) 2009-2024 by Volker Theile. All rights reserved.
To manage the system visit the openmediavault workbench:
eth0: 192.168.1.24
eth0: 2804:7f74:95a:5200:c090:9aff:feb0:fdd6
eth0: fe80::c090:9aff:feb0:fdd6
veth8d8e186f: 172.16.16.1
veth8d8e186f: fe80::4083:2dff:fe25:faed
By default the workbench administrator account has the
username 'admin' and password 'openmediavault'.
It is recommended that you change the password for this account
within the workbench or using the 'omv-firstaid' CLI command.
For more information regarding this appliance, please visit the
web site: https://www.openmediavault.org
lua login: [ 109.087398][ T2222] Initializing XFRM netlink socket
[ 110.574690][ T2184] br-9170f205218d: port 1(veth240db2f) entered blocking state
[ 110.582511][ T2184] br-9170f205218d: port 1(veth240db2f) entered disabled state
[ 110.590357][ T2184] veth240db2f: entered allmulticast mode
[ 110.597040][ T2184] veth240db2f: entered promiscuous mode
[ 110.616720][ T2184] br-9170f205218d: port 1(veth240db2f) entered blocking state
[ 110.624159][ T2184] br-9170f205218d: port 1(veth240db2f) entered forwarding state
[ 110.636601][ T101] br-9170f205218d: port 1(veth240db2f) entered disabled state
[ 110.949113][ T2182] br-9170f205218d: port 2(vethc84232a) entered blocking state
[ 110.959839][ T2182] br-9170f205218d: port 2(vethc84232a) entered disabled state
[ 110.968007][ T2182] vethc84232a: entered allmulticast mode
[ 110.974819][ T2182] vethc84232a: entered promiscuous mode
[ 110.995672][ T2182] br-9170f205218d: port 2(vethc84232a) entered blocking state
[ 111.003110][ T2182] br-9170f205218d: port 2(vethc84232a) entered forwarding state
[ 111.014412][ T6] IPv6: ADDRCONF(NETDEV_CHANGE): br-9170f205218d: link becomes ready
[ 111.026845][ T6] br-9170f205218d: port 2(vethc84232a) entered disabled state
[ 111.042476][ T2182] docker0: port 1(vethba6e0d3) entered blocking state
[ 111.062304][ T2182] docker0: port 1(vethba6e0d3) entered disabled state
[ 111.069037][ T2182] vethba6e0d3: entered allmulticast mode
[ 111.081515][ T2182] vethba6e0d3: entered promiscuous mode
[ 111.092876][ T2182] docker0: port 1(vethba6e0d3) entered blocking state
[ 111.099591][ T2182] docker0: port 1(vethba6e0d3) entered forwarding state
[ 111.111097][ T6] docker0: port 1(vethba6e0d3) entered disabled state
[ 111.181696][ T2188] br-5075e9ce5e42: port 1(vethfc2ddfe) entered blocking state
[ 111.205076][ T2188] br-5075e9ce5e42: port 1(vethfc2ddfe) entered disabled state
[ 111.219113][ T2188] vethfc2ddfe: entered allmulticast mode
[ 111.254869][ T2188] vethfc2ddfe: entered promiscuous mode
[ 111.581825][ T2186] br-9170f205218d: port 3(veth976768d) entered blocking state
[ 111.590834][ T2186] br-9170f205218d: port 3(veth976768d) entered disabled state
[ 111.598873][ T2186] veth976768d: entered allmulticast mode
[ 111.607064][ T2186] veth976768d: entered promiscuous mode
[ 111.615697][ T2186] br-9170f205218d: port 3(veth976768d) entered blocking state
[ 111.623155][ T2186] br-9170f205218d: port 3(veth976768d) entered forwarding state
[ 111.634508][ T101] br-9170f205218d: port 3(veth976768d) entered disabled state
[ 112.343269][ T2082] br-9170f205218d: port 4(veth5a49821) entered blocking state
[ 112.354545][ T2082] br-9170f205218d: port 4(veth5a49821) entered disabled state
[ 112.382206][ T2082] veth5a49821: entered allmulticast mode
[ 112.395435][ T2082] veth5a49821: entered promiscuous mode
[ 112.439265][ T2186] br-9170f205218d: port 4(veth5a49821) entered blocking state
[ 112.446694][ T2186] br-9170f205218d: port 4(veth5a49821) entered forwarding state
[ 112.465345][ T882] br-9170f205218d: port 4(veth5a49821) entered disabled state
[ 114.182350][ T2560] br-5075e9ce5e42: port 1(vethfc2ddfe) entered disabled state
[ 114.217228][ T2560] vethfc2ddfe (unregistering): left allmulticast mode
[ 114.228465][ T2560] vethfc2ddfe (unregistering): left promiscuous mode
[ 114.254966][ T2560] br-5075e9ce5e42: port 1(vethfc2ddfe) entered disabled state
[ 116.645716][ T2562] eth0: renamed from veth971cc8d
[ 116.700657][ T21] IPv6: ADDRCONF(NETDEV_CHANGE): veth240db2f: link becomes ready
[ 116.708442][ T21] br-9170f205218d: port 1(veth240db2f) entered blocking state
[ 116.715821][ T21] br-9170f205218d: port 1(veth240db2f) entered forwarding state
[ 117.067117][ T2560] eth0: renamed from veth61e3ef0
[ 117.099015][ T101] IPv6: ADDRCONF(NETDEV_CHANGE): veth976768d: link becomes ready
[ 117.112245][ T101] br-9170f205218d: port 3(veth976768d) entered blocking state
[ 117.119691][ T101] br-9170f205218d: port 3(veth976768d) entered forwarding state
[ 117.749846][ T2188] eth0: renamed from veth185b9b2
[ 117.849902][ T2538] eth0: renamed from vethdc03ac8
[ 117.986134][ T2461] eth0: renamed from veth18c5549
[ 118.029206][ T882] IPv6: ADDRCONF(NETDEV_CHANGE): veth5a49821: link becomes ready
[ 118.036970][ T882] br-9170f205218d: port 4(veth5a49821) entered blocking state
[ 118.044374][ T882] br-9170f205218d: port 4(veth5a49821) entered forwarding state
[ 118.073807][ T101] IPv6: ADDRCONF(NETDEV_CHANGE): vethba6e0d3: link becomes ready
[ 118.088124][ T101] docker0: port 1(vethba6e0d3) entered blocking state
[ 118.094845][ T101] docker0: port 1(vethba6e0d3) entered forwarding state
[ 118.109771][ T101] IPv6: ADDRCONF(NETDEV_CHANGE): vethc84232a: link becomes ready
[ 118.123932][ T101] br-9170f205218d: port 2(vethc84232a) entered blocking state
[ 118.131357][ T101] br-9170f205218d: port 2(vethc84232a) entered forwarding state
[ 118.151884][ T101] IPv6: ADDRCONF(NETDEV_CHANGE): docker0: link becomes ready
lua login: root
Password:
Linux lua 6.4.11-mvebu-tld-1 #1 SMP PREEMPT Sun Aug 20 03:17:26 PDT 2023 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Wed Jul 10 23:05:34 -03 2024 on ttyS0
lua
172.18.0.1 n
172.19.0.1 n
172.17.0.1 n
192.168.1.24
172.16.16.1
WD MyCloud Ex2 Ultra
Linux version 6.4.11-mvebu-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT S3
Debian 11.10
Sat Jul 13 22:54:07 -03 2024 up 2 minutes
root@lua:~#
[...]
and there was light.
Your guidance made the ex2 work again. Thank you.
However, I still think about keeping on NAND:
- u-boot
- uImage
- uInitrd
- rescuefw like WD-to-Debian-Stretch.bin
as suggested at the beginning of this tutorial (or something better that you suggest).
I don't plan to go back to the manufacturer's firmware...
Once again, thank you for your attention and help.
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 14, 2024 03:14PM |
Admin Registered: 13 years ago Posts: 18,997 |
> I changed sda1 to sdb1, because rootfs usb is
> sdb1
That's expected. The rootfs USB drive could be assigned any driver letter, depending on how many SATA drives and USB drives are attched. To make it resilient, the bootargs should be:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> sdb1
That's expected. The rootfs USB drive could be assigned any driver letter, depending on how many SATA drives and USB drives are attched. To make it resilient, the bootargs should be:
setenv set_bootargs_debian 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs $(mtdparts) earlyprintk=serial init=/bin/system'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Anderson
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 17, 2024 12:06PM |
|
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 17, 2024 04:55PM |
Admin Registered: 13 years ago Posts: 18,997 |
I forget if this box u-boot can see the HDDs.
With at least one HDD in the slots. Power up, interrupt u-boot countdown and,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
With at least one HDD in the slots. Power up, interrupt u-boot countdown and,
help scsi reset
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Anderson
Re: How to install Debian in a WD MyCloud EX2 Ultra: Definitive edition July 17, 2024 09:11PM |
Marvell>> scsi reset
Reset SCSI
AHCI init for unit0
Target spinup took 0 ms.
SATA link 1 timeout.
Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found
scanning bus for devices...
Device 0: (0:0) Vendor: ATA Prod.: WDC WD5000LPCX-2 Rev: 02.0
Type: Hard Disk
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
Found 1 device(s).
in this HD is the same rootfs of USB... how make u-boot boot then?
Thanks
