Re: Debian on Dell Wyse 3020 February 25, 2024 01:38PM |
Admin Registered: 13 years ago Posts: 18,976 |
Re: Debian on Dell Wyse 3020 February 25, 2024 04:09PM |
Admin Registered: 13 years ago Posts: 18,976 |
Re: Debian on Dell Wyse 3020 February 26, 2024 09:33PM |
Admin Registered: 13 years ago Posts: 18,976 |
md5: 8a84e9d35625d3fc5ddd07b52ab271f2 sha256: cb96edad9c0b47ed13bef090d661d2c81fb7650f40269068ad3d461fa72d3a26This tarball contains 5 files
linux-image-6.7.5-mvebu-tld-2_2_armhf.deb linux-headers-6.7.5-mvebu-tld-2_2_armhf.deb zImage-6.7.5-mvebu-tld-2 config-6.7.5-mvebu-tld-2 linux-dtb-6.7.5-mvebu-tld-2.tar
Re: Debian on Dell Wyse 3020 February 27, 2024 02:14AM |
Registered: 9 months ago Posts: 38 |
*** FlashNumber... Code: : *** Loading Next Image... *** Loading Next Image... *** Set Partition for Image... *** Validate Image... *** GPIO_14, GPIO_13 both low ... Controller1 DDR size reg is 0xE ... *** Your OBM Boot Test Successes ... *** Shutting ports and transferring control ... 123ABC 12345 [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.7.5-mvebu-tld-2 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 SMP PREEMPT Sun Feb 25 19:19:00 PST 2024 [ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: div instructions available: patching division code [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Dell Ariel [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000007fefffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000007fefffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fefffff] [ 0.000000][ T0] percpu: Embedded 29 pages/cpu s25364 r8192 d85228 u118784 [ 0.000000][ T0] Kernel command line: rootdelay=5 root=LABEL=mmcrootfs raid=noautodetect console=ttyS2,115200 mtdparts=spi0.0:4m(boot) [ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 522304 [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 2052660K/2096128K available (10240K kernel code, 873K rwdata, 3536K rodata, 1024K init, 318K bss, 43468K reserved, 0K cma-reserved, 1309696K highmem) [ 0.000000][ T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: platform modifies aux control register: 0x02060000 -> 0x32860000 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x02060000 -> 0x32860000 [ 0.000000][ T0] Tauros3 cache controller enabled, 8 ways, 512 kB [ 0.000000][ T0] Tauros3: CACHE_ID 0x880000ed, AUX_CTRL 0x32860000 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000006][ T0] sched_clock: 32 bits at 26MHz, resolution 38ns, wraps every 82595524588ns [ 0.000068][ T0] clocksource: clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 73510017198 ns [ 0.000283][ T0] smp_twd: clock not found -2 [ 0.000792][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval) [ 0.001281][ T0] Console: colour dummy device 80x30 [ 0.001329][ T0] Calibrating local timer... 2.16MHz. [ 0.060263][ T0] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.100287][ T0] CPU: Testing write buffer coherency: ok [ 0.100363][ T0] pid_max: default: 32768 minimum: 301 [ 0.104625][ T0] LSM: initializing lsm=capability,integrity [ 0.106018][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.106038][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.112022][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.114178][ T1] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. [ 0.114441][ T1] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. [ 0.114646][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.115257][ T1] rcu: Hierarchical SRCU implementation. [ 0.115267][ T1] rcu: Max phase no-delay instances is 1000. [ 0.116720][ T1] smp: Bringing up secondary CPUs ... [ 0.150293][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.151059][ T1] smp: Brought up 1 node, 2 CPUs [ 0.151080][ T1] SMP: Total of 2 processors activated (2382.23 BogoMIPS). [ 0.151091][ T1] CPU: All CPU(s) started in SVC mode. [ 0.153445][ T1] devtmpfs: initialized [ 0.164919][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.165513][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.165555][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.168551][ T1] prandom: seed boundary self test passed [ 0.171127][ T1] prandom: 100 self tests passed [ 0.171141][ T1] pinctrl core: initialized pinctrl subsystem [ 0.173422][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.174114][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.185125][ T1] audit: initializing netlink subsys (disabled) [ 0.186535][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.186640][ T30] audit: type=2000 audit(0.190:1): state=initialized audit_enabled=0 res=1 [ 0.186716][ T1] cpuidle: using governor ladder [ 0.186769][ T1] cpuidle: using governor menu [ 0.187004][ T19] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 [ 0.187019][ T19] hw-breakpoint: CPU 0 failed to disable vector catch [ 0.187081][ T20] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 [ 0.190857][ T1] platform soc: Fixed dependency cycle(s) with /soc/interrupt-controller@e0001000 [ 0.370512][ T1] raid6: int32x8 gen() 222 MB/s [ 0.540607][ T1] raid6: int32x4 gen() 236 MB/s [ 0.710719][ T1] raid6: int32x2 gen() 362 MB/s [ 0.880841][ T1] raid6: int32x1 gen() 357 MB/s [ 0.880855][ T1] raid6: using algorithm int32x2 gen() 362 MB/s [ 1.050942][ T1] raid6: .... xor() 219 MB/s, rmw enabled [ 1.050952][ T1] raid6: using intx1 recovery algorithm [ 1.053066][ T1] SCSI subsystem initialized [ 1.053744][ T1] usbcore: registered new interface driver usbfs [ 1.053841][ T1] usbcore: registered new interface driver hub [ 1.053936][ T1] usbcore: registered new device driver usb [ 1.054407][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.054418][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.054449][ T1] PTP clock support registered [ 1.057410][ T1] vgaarb: loaded [ 1.058328][ T1] clocksource: Switched to clocksource clocksource [ 1.070367][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.070930][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.096084][ T1] NET: Registered PF_INET protocol family [ 1.096513][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.098867][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.099163][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.099243][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.099370][ T1] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 1.099510][ T1] TCP: Hash tables configured (established 8192 bind 8192) [ 1.100400][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 1.100963][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.101005][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.102078][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.103584][ T1] RPC: Registered named UNIX socket transport module. [ 1.103599][ T1] RPC: Registered udp transport module. [ 1.103608][ T1] RPC: Registered tcp transport module. [ 1.103616][ T1] RPC: Registered tcp-with-tls transport module. [ 1.103624][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.103653][ T1] PCI: CLS 0 bytes, default 64 [ 1.109147][ T29] Trying to unpack rootfs image as initramfs... [ 1.109553][ T1] Initialise system trusted keyrings [ 1.109687][ T1] Key type blacklist registered [ 1.110285][ T1] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 1.110392][ T1] zbud: loaded [ 1.134638][ T1] NFS: Registering the id_resolver key type [ 1.134711][ T1] Key type id_resolver registered [ 1.134720][ T1] Key type id_legacy registered [ 1.135093][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.135126][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.292593][ T1] xor: measuring software checksum speed [ 1.300917][ T1] arm4regs : 1197 MB/sec [ 1.312491][ T1] 8regs : 855 MB/sec [ 1.321667][ T1] 32regs : 1081 MB/sec [ 1.321685][ T1] xor: using function: arm4regs (1197 MB/sec) [ 1.321718][ T1] async_tx: api initialized (async) [ 1.321745][ T1] Key type asymmetric registered [ 1.321759][ T1] Asymmetric key parser 'x509' registered [ 1.322516][ T1] bounce: pool size: 64 pages [ 1.323697][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.324700][ T1] io scheduler bfq registered [ 1.350865][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 1.376783][ T29] Freeing initrd memory: 5172K [ 1.587360][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.597392][ T1] printk: legacy console [ttyS2] disabled [ 1.600094][ T1] d4018000.serial: ttyS2 at MMIO 0xd4018000 (irq = 381, base_baud = 1625000) is a XScale [ 1.600187][ T1] printk: legacy console [ttyS2] enabled [ 2.513473][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 2.522331][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 2.543147][ T1] usbcore: registered new interface driver smsc75xx [ 2.553772][ T1] mv-ehci d4208000.usb: EHCI Host Controller [ 2.559742][ T1] mv-ehci d4208000.usb: new USB bus registered, assigned bus number 1 [ 2.569131][ T1] mv-ehci d4208000.usb: irq 382, io mem 0xd4208000 [ 2.608404][ T1] mv-ehci d4208000.usb: USB 2.0 started, EHCI 1.00 [ 2.615147][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.07 [ 2.624110][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.632025][ T1] usb usb1: Product: EHCI Host Controller [ 2.637558][ T1] usb usb1: Manufacturer: Linux 6.7.5-mvebu-tld-2 ehci_hcd [ 2.644602][ T1] usb usb1: SerialNumber: d4208000.usb [ 2.651643][ T1] hub 1-0:1.0: USB hub found [ 2.656136][ T1] hub 1-0:1.0: 1 port detected [ 2.661989][ T1] mv-ehci d4208000.usb: successful find EHCI device with regs 0x(ptrval) irq 382 working in Host mode [ 2.673573][ T1] usbcore: registered new interface driver usblp [ 2.680084][ T1] usbcore: registered new interface driver usb-storage [ 2.687948][ T1] mousedev: PS/2 mouse device common for all mice [ 2.696536][ T1] i2c_dev: i2c /dev entries driver [ 2.704675][ T1] device-mapper: uevent: version 1.0.3 [ 2.710927][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 2.720822][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 2.728007][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 2.735341][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 2.742886][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 2.750180][ T1] sdhci: Secure Digital Host Controller Interface driver [ 2.757009][ T1] sdhci: Copyright(c) Pierre Ossman [ 2.763642][ T1] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.771422][ T1] hid: raw HID events driver (C) Jiri Kosina [ 2.780373][ T1] usbcore: registered new interface driver usbhid [ 2.786682][ T1] usbhid: USB HID core driver [ 2.794447][ T1] NET: Registered PF_INET6 protocol family [ 2.803710][ T1] Segment Routing with IPv6 [ 2.808049][ T1] RPL Segment Routing with IPv6 [ 2.812838][ T25] mmc0: SDHCI controller on d4281000.mmc [d4281000.mmc] using ADMA [ 2.820736][ T1] In-situ OAM (IOAM) with IPv6 [ 2.825536][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.836009][ T1] NET: Registered PF_PACKET protocol family [ 2.842369][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 2.847396][ T1] Key type dns_resolver registered [ 2.853006][ T1] ThumbEE CPU extension supported. [ 2.858444][ T1] Registering SWP/SWPB emulation handler [ 2.864110][ T1] PJ4 iWMMXt v2 coprocessor enabled. [ 2.949699][ T68] usb 1-1: new high-speed USB device number 2 using mv-ehci [ 2.965777][ T1] registered taskstats version 1 [ 2.971378][ T1] Loading compiled-in X.509 certificates [ 3.011717][ T1] Key type .fscrypt registered [ 3.016326][ T1] Key type fscrypt-provisioning registered [ 3.022288][ T1] Key type big_key registered [ 3.047840][ T1] Key type encrypted registered [ 3.073207][ T26] mv-ehci f0001000.usb: EHCI Host Controller [ 3.080144][ T26] mv-ehci f0001000.usb: new USB bus registered, assigned bus number 2 [ 3.088803][ T26] mv-ehci f0001000.usb: irq 384, io mem 0xf0001000 [ 3.137490][ T8] mmc0: new HS200 MMC card at address 0001 [ 3.144788][ T8] mmcblk0: mmc0:0001 H4G2a 3.64 GiB [ 3.153560][ T8] mmcblk0: p1 p2 [ 3.158435][ T26] mv-ehci f0001000.usb: USB 2.0 started, EHCI 1.00 [ 3.158524][ T8] mmcblk0boot0: mmc0:0001 H4G2a 4.00 MiB [ 3.165549][ T26] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.07 [ 3.173067][ T68] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63 [ 3.179439][ T26] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.189961][ T8] mmcblk0boot1: mmc0:0001 H4G2a 4.00 MiB [ 3.196152][ T26] usb usb2: Product: EHCI Host Controller [ 3.201915][ T68] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 3.208036][ T26] usb usb2: Manufacturer: Linux 6.7.5-mvebu-tld-2 ehci_hcd [ 3.215396][ T68] usb 1-1: Product: USB2.0 Hub [ 3.222276][ T26] usb usb2: SerialNumber: f0001000.usb [ 3.232357][ T8] mmcblk0rpmb: mmc0:0001 H4G2a 4.00 MiB, chardev (244:0) [ 3.234617][ T26] hub 2-0:1.0: USB hub found [ 3.240450][ T68] hub 1-1:1.0: USB hub found [ 3.245206][ T26] hub 2-0:1.0: 1 port detected [ 3.248708][ T68] hub 1-1:1.0: 4 ports detected [ 3.255794][ T26] mv-ehci f0001000.usb: successful find EHCI device with regs 0x(ptrval) irq 384 working in Host mode [ 3.270812][ T1] clk: Disabling unused clocks [ 3.279041][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 3.330505][ T1] Checked W+X mappings: passed, no W+X pages found [ 3.336912][ T1] Run /init as init process [ 3.343289][ T1] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004 [ 3.351596][ T1] CPU: 0 PID: 1 Comm: init Not tainted 6.7.5-mvebu-tld-2 #2 [ 3.358681][ T1] Hardware name: Marvell MMP3 [ 3.363184][ T1] unwind_backtrace from show_stack+0x10/0x14 [ 3.369090][ T1] show_stack from dump_stack_lvl+0x40/0x4c [ 3.374811][ T1] dump_stack_lvl from panic+0x104/0x308 [ 3.380265][ T1] panic from do_exit+0x264/0x8b8 [ 3.385123][ T1] do_exit from sys_exit_group+0x0/0x10 [ 3.390509][ C1] CPU1: stopping [ 3.390519][ C1] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.7.5-mvebu-tld-2 #2 [ 3.390530][ C1] Hardware name: Marvell MMP3 [ 3.390538][ C1] unwind_backtrace from show_stack+0x10/0x14 [ 3.390562][ C1] show_stack from dump_stack_lvl+0x40/0x4c [ 3.390578][ C1] dump_stack_lvl from do_handle_IPI+0x84/0x11c [ 3.390595][ C1] do_handle_IPI from ipi_handler+0x14/0x20 [ 3.390612][ C1] ipi_handler from handle_percpu_devid_irq+0x4c/0xe8 [ 3.390641][ C1] handle_percpu_devid_irq from handle_irq_desc+0x1c/0x2c [ 3.390660][ C1] handle_irq_desc from gic_handle_irq+0x58/0x64 [ 3.390678][ C1] gic_handle_irq from generic_handle_arch_irq+0x28/0x3c [ 3.390694][ C1] generic_handle_arch_irq from call_with_stack+0x18/0x20 [ 3.390716][ C1] call_with_stack from __irq_svc+0x98/0xc8 [ 3.390731][ C1] Exception stack(0xf0859f60 to 0xf0859fa8) [ 3.390747][ C1] 9f60: 00000001 c0ded327 00002794 00000001 00000000 00000000 00000001 c194ba80 [ 3.390759][ C1] 9f80: c100a010 c100a04c 00000000 00000000 00000000 f0859fb0 c0a9d158 c0156e38 [ 3.390768][ C1] 9fa0: 200c0013 ffffffff [ 3.390775][ C1] __irq_svc from do_idle+0x108/0x280 [ 3.390795][ C1] do_idle from cpu_startup_entry+0x28/0x2c [ 3.390812][ C1] cpu_startup_entry from secondary_start_kernel+0xfc/0x11c [ 3.390830][ C1] secondary_start_kernel from 0x1016a0 [ 3.519132][ T1] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004 ]---
KERNEL_VERSION=6.7.5-mvebu-tld-2 cat zImage-${KERNEL_VERSION} dts/mmp3-dell-ariel.dtb > zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x8000 -e 0x8000 -n Linux-${KERNEL_VERSION} -d zImage.fdt uImage mkimage -A arm -O linux -T ramdisk -C gzip -a 0x3000000 -e 0x3000000 -d initrd.img-${KERNEL_VERSION} uInitrd- I copied created uImage/uInitrd files to the boot partition and rebooted the system
Re: Debian on Dell Wyse 3020 February 27, 2024 01:44PM |
Admin Registered: 13 years ago Posts: 18,976 |
Re: Debian on Dell Wyse 3020 March 03, 2024 04:25PM |
Admin Registered: 13 years ago Posts: 18,976 |
Re: Debian on Dell Wyse 3020 April 01, 2024 05:21AM |
Registered: 7 months ago Posts: 4 |
Re: Debian on Dell Wyse 3020 April 01, 2024 02:15PM |
Admin Registered: 13 years ago Posts: 18,976 |
Quote
I create a FAT32 partition mounted at /mnt/bootfs to hold the kernel/initrd/wloader.conf, then I create an ext3 filesystem mounted at /mnt/rootfs to hold the rootfs. From there I just extract everything as necessary and delete unused files:
tar -C /mnt/rootfs/ -x -j -f ~/Downloads/Debian-5.13.8-mvebu-tld-1-rootfs-bodhi.tar.bz2
tar -C /mnt/BOOTFS/ -x -j -f ~/Downloads/linux-6.2.8-mvebu-tld-2.x-bodhi.tar.bz2
cat /mnt/BOOTFS/zImage-6.2.8-mvebu-tld-2.0 /mnt/BOOTFS/dts/mmp3-dell-ariel.dtb > /mnt/BOOTFS/zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -d /mnt/BOOTFS/zImage.fdt /mnt/BOOTFS/uImage
mkimage -A arm -O linux -T ramdisk -C gzip -d /mnt/rootfs/boot/initrd.img-5.13.8-mvebu-tld-1 /mnt/BOOTFS/uInitrd
wloader.conf looks like this:
<TX0D_START>
kernel=uImage
initrd=uInitrd
param="rootdelay=5 root=/dev/sda2 console=ttyS2,115200 raid=noautodetect"
<TX0D_END>
/mnt/bootfs looks like this:
drwxr-xr-x 2 mischif mischif 1536 Dec 31 1969 .
-rw-r--r-- 1 mischif mischif 4973597 Apr 9 21:24 uImage
-rw-r--r-- 1 mischif mischif 9649885 Apr 9 21:26 uInitrd
-rw-r--r-- 1 mischif mischif 136 Apr 9 21:28 wloader.cfg
drwxr-x---+ 4 root root 34 Apr 9 21:45 ..
Quote
Modify the wloader.cfg
<TX0D_START> kernel=uImage initrd=uInitrd param="rootdelay=5 root=LABEL=rootfs raid=noautodetect console=ttyS2,115200 mtdparts=spi1.0:4m(boot)" <TX0D_END>
Max
Re: Debian on Dell Wyse 3020 April 03, 2024 05:21AM |
max@max-OptiPlex-3020:~/Downloads$ ls /media/max/BOOTFS/ config-6.5.7-mvebu-tld-1 dts linux-6.5.7-mvebu-tld-1.patch linux-dtb-6.5.7-mvebu-tld-1.tar linux-headers-6.5.7-mvebu-tld-1_1_armhf.deb linux-image-6.5.7-mvebu-tld-1_1_armhf.deb uImage uInitrd zImage-6.5.7-mvebu-tld-1 zImage.fdt
max@max-OptiPlex-3020:~/Downloads$ ls /media/max/rootfs/ bin dev home lost+found mnt proc run srv tmp var boot etc lib media opt root sbin sys usr
Re: Debian on Dell Wyse 3020 April 03, 2024 09:35AM |
Registered: 9 months ago Posts: 38 |
Max
Re: Debian on Dell Wyse 3020 April 03, 2024 11:49AM |
Re: Debian on Dell Wyse 3020 April 03, 2024 01:48PM |
Registered: 9 months ago Posts: 38 |
Re: Debian on Dell Wyse 3020 April 03, 2024 02:04PM |
Admin Registered: 13 years ago Posts: 18,976 |
Max
Re: Debian on Dell Wyse 3020 April 04, 2024 10:43AM |
Re: Debian on Dell Wyse 3020 April 04, 2024 02:11PM |
Admin Registered: 13 years ago Posts: 18,976 |
modprobe mmc_block
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-6.5.7-mvebu-tld-1 -d initrd.img-6.5.7-mvebu-tld-1 uInitrd
Re: Debian on Dell Wyse 3020 April 05, 2024 06:40AM |
Registered: 7 months ago Posts: 4 |
root@debian:~# modprobe mmc_block modprobe: FATAL: Module mmc_block not found in directory /lib/modules/6.5.7-mvebu-tld-1
Re: Debian on Dell Wyse 3020 April 05, 2024 02:09PM |
Admin Registered: 13 years ago Posts: 18,976 |
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x3000000 -e 0x3000000 -n initramfs 6.5.7-mvebu-tld-1 -d initrd.img-6.57-mvebu-tld-1 uInitrd
uname -a ls -lart /boot find /lib/modules/6.5.7-mvebu-tld-1/ -name '*mmc*'
Max
Re: Debian on Dell Wyse 3020 April 06, 2024 04:13AM |
Re: Debian on Dell Wyse 3020 April 06, 2024 04:45AM |
Registered: 9 months ago Posts: 38 |
dpkg -i linux-image-6.5.7-mvebu-tld-1_1_armhf.debcommand in a folder where you unpacked the 6.5.7 kernel. If you unpacked it into bootfs then you may to need to mount it first or even simpler - attach the usb stick back to you main computer and unpack kernel archive somewhere on your rootfs - I usually use the /boot folder on rootfs for it.
Re: Debian on Dell Wyse 3020 April 06, 2024 01:14PM |
Registered: 7 months ago Posts: 4 |
Re: Debian on Dell Wyse 3020 April 06, 2024 01:23PM |
Registered: 9 months ago Posts: 38 |
Re: Debian on Dell Wyse 3020 April 07, 2024 06:52AM |
Registered: 7 months ago Posts: 4 |
Re: Debian on Dell Wyse 3020 April 07, 2024 07:26AM |
Registered: 9 months ago Posts: 38 |
Max
Re: Debian on Dell Wyse 3020 April 07, 2024 09:47AM |
Re: Debian on Dell Wyse 3020 April 11, 2024 08:28AM |
Registered: 11 months ago Posts: 4 |
Re: Debian on Dell Wyse 3020 April 11, 2024 10:42AM |
Registered: 9 months ago Posts: 38 |
Re: Debian on Dell Wyse 3020 April 15, 2024 10:23PM |
Registered: 6 months ago Posts: 6 |
[root@localhost home]# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 15G 0 disk ├─sda1 8:1 0 1G 0 part /boot └─sda2 8:2 0 14G 0 part ├─fedora-root 253:0 0 12.5G 0 lvm / └─fedora-swap 253:1 0 1.5G 0 lvm [SWAP] sdb 8:16 1 14.9G 0 disk sr0 11:0 1 1024M 0 rom [root@localhost home]# arm-image-installer --resizefs --target=olpc_xo175 --media=/dev/sdb --image=/ home/Fedora-Minimal-armhfp-32-1.6-sda.raw.xz ===================================================== = Selected Image: = /home/Fedora-Minimal-armhfp-32-1.6-sda.raw.xz = Selected Media : /dev/sdb = U-Boot Target : olpc_xo175 = Root partition will be resized ===================================================== ***************************************************** ***************************************************** ******** WARNING! ALL DATA WILL BE DESTROYED ******** ***************************************************** ***************************************************** Type 'YES' to proceed, anything else to exit now = Proceed? YES = Writing: = /home/Fedora-Minimal-armhfp-32-1.6-sda.raw.xz = To: /dev/sdb .... 196878336 bytes (197 MB, 188 MiB) copied, 1 s, 197 MB/s 291545088 bytes (292 MB, 278 MiB) copied, 2 s, 146 MB/s ... 2081914880 bytes (2.1 GB, 1.9 GiB) copied, 303 s, 6.9 MB/s 2087419904 bytes (2.1 GB, 1.9 GiB) copied, 304 s, 6.9 MB/s 0+157215 records in 0+157215 records out 2088763392 bytes (2.1 GB, 1.9 GiB) copied, 485.728 s, 4.3 MB/s = Writing image complete! = Resizing /dev/sdb .... Checking that no-one is using this disk right now ... OK [1mDisk /dev/sdb: 14.94 GiB, 16015949824 bytes, 31281152 sectors [0mDisk model: USB 2.0 FD Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xbacf5465 Old situation: [1mDevice[0m [1mBoot[0m [1m Start[0m [1m End[0m [1mSectors[0m [1m Size[0m [1mId[0m [1mType[0m /dev/sdb1 8192 163839 155648 76M c W95 FAT32 (LBA) /dev/sdb2 * 163840 1163263 999424 488M 83 Linux /dev/sdb3 1163264 3899391 2736128 1.3G 83 Linux /dev/sdb3: New situation: Disklabel type: dos Disk identifier: 0xbacf5465 [1mDevice[0m [1mBoot[0m [1m Start[0m [1m End[0m [1m Sectors[0m [1m Size[0m [1mId[0m [1mType[0m /dev/sdb1 8192 163839 155648 76M c W95 FAT32 (LBA) /dev/sdb2 * 163840 1163263 999424 488M 83 Linux /dev/sdb3 1163264 31281151 30117888 14.4G 83 Linux The partition table has been altered. Calling ioctl() to re-read partition table. Syncing disks. e2fsck 1.45.5 (07-Jan-2020) Pass 1: Checking inodes, blocks, and sizes Pass 2: Checking directory structure Pass 3: Checking directory connectivity Pass 4: Checking reference counts Pass 5: Checking group summary information _/: 36555/85536 files (1.3% non-contiguous), 271034/342016 blocks resize2fs 1.45.5 (07-Jan-2020) Resizing the filesystem on /dev/sdb3 to 3764736 (4k) blocks. The filesystem on /dev/sdb3 is now 3764736 (4k) blocks long. = Copying loader scripts to boot partition = Installation Complete! Insert into the olpc_xo175 and boot. [root@localhost home]# mount /dev/sdb2 /mnt [root@localhost home]# mount /dev/sdb1 /mnt/efi/ [root@localhost home]# rm -rf /mnt/efi/* [root@localhost home]# cat /mnt/vmlinuz-* /mnt/dtb-*/mmp3-dell-ariel.dtb >/mnt/zImage [root@localhost home]# mkimage -A arm -O linux -C none -T kernel -a 0x00008000 -e 0x00008000 -d /mn t/zImage /mnt/efi/uImage Image Name: Created: Mon Apr 15 23:03:12 2024 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 7654917 Bytes = 7475.50 KiB = 7.30 MiB Load Address: 00008000 Entry Point: 00008000 [root@localhost home]# mkimage -A arm -O linux -C none -T ramdisk -d /mnt/initramfs-* /mnt/efi/uIni trd Image Name: Created: Mon Apr 15 23:03:26 2024 Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 51619027 Bytes = 50409.21 KiB = 49.23 MiB Load Address: 00000000 Entry Point: 00000000 [root@localhost home]# nano /mnt/efi/wloader.cfg <TX0D_START> kernel=./uImage initrd=./uInitrd param="$(sed -n 's/^[\t ]*append //p' /mnt/extlinux/extlinux.conf)" <TX0D_END> [root@localhost home]# umount /mnt/efi /mnt [root@localhost home]# umount /mnt/efi /mntexit Script done on 2024-04-15 23:06:38-04:00 [COMMAND_EXIT_CODE="0"]
Re: Debian on Dell Wyse 3020 April 16, 2024 12:32AM |
Admin Registered: 13 years ago Posts: 18,976 |
Re: Debian on Dell Wyse 3020 April 17, 2024 01:41AM |
Registered: 6 months ago Posts: 6 |
Re: Debian on Dell Wyse 3020 April 17, 2024 06:22PM |
Admin Registered: 13 years ago Posts: 18,976 |
Quote
Unbricking with Serial Console & JTAG console
How to unbrick your box using serial console with kwboot
....
Serial Port connector - what are people using to make it work