PogoPlug E02 unusable May 26, 2023 05:10PM |
Registered: 1 year ago Posts: 10 |
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.100000] Using static partition definition [ 1.110000] Creating 4 MTD partitions on "nand_mtd": [ 1.110000] 0x00000000-0x00100000 : "u-boot" [ 1.120000] 0x00100000-0x00500000 : "uImage" [ 1.120000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 1.880000] usbcore: registered new interface driver usblp [ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.890000] Initializing USB Mass Storage driver... [ 1.890000] usbcore: registered new interface driver usb-storage [ 1.900000] USB Mass Storage support registered. [ 1.910000] mice: PS/2 mouse device common for all mice [ 1.910000] i2c /dev entries driver [ 1.910000] Linux telephony interface: v1.00 [ 1.920000] md: linear personality registered for level -1 [ 1.920000] md: raid0 personality registered for level 0 [ 1.930000] md: raid1 personality registered for level 1 [ 2.100000] raid6: int32x1 97 MB/s [ 2.270000] raid6: int32x2 114 MB/s [ 2.440000] raid6: int32x4 122 MB/s [ 2.610000] raid6: int32x8 110 MB/s [ 2.610000] raid6: using algorithm int32x4 (122 MB/s) [ 2.610000] md: raid6 personality registered for level 6 [ 2.620000] md: raid5 personality registered for level 5 [ 2.620000] md: raid4 personality registered for level 4 [ 2.630000] raid5: measuring checksumming speed [ 2.680000] arm4regs : 1084.000 MB/sec [ 2.730000] 8regs : 754.800 MB/sec [ 2.780000] 32regs : 899.600 MB/sec [ 2.780000] raid5: using function: arm4regs (1084.000 MB/sec) [ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.790000] dm_crypt using the OCF package. [ 2.800000] sdhci: Secure Digital Host Controller Interface driver [ 2.800000] sdhci: Copyright(c) Pierre Ossman [ 2.810000] usbcore: registered new interface driver usbhid [ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.820000] TCP cubic registered [ 2.820000] NET: Registered protocol family 1 [ 2.830000] NET: Registered protocol family 17 [ 2.830000] md: Autodetecting RAID arrays. [ 2.840000] md: autorun ... [ 2.840000] md: ... autorun DONE. [ 5.740000] Empty flash at 0x009ac208 ends at 0x009ac800 [ 7.110000] jffs2_scan_eraseblock(): Node at 0x010a07f8 {0x1985, 0xe001, 0x00000032) has invalid CRC 0xffffffff (calculated 0x503776f3) [ 7.120000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x010a07fc: 0x0032 instead [ 9.040000] VFS: Mounted root (jffs2 filesystem) readonly. [ 9.050000] Freeing init memory: 124K
Re: PogoPlug E02 unusable May 26, 2023 05:27PM |
Admin Registered: 13 years ago Posts: 18,821 |
Hit any key to stop autoboot: 0And enter the setenv commands to boot into USB rootfs.
Re: PogoPlug E02 unusable May 30, 2023 12:54AM |
Registered: 1 year ago Posts: 10 |
baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes console=console=ttyS0,115200 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/mtdblock2 ro ethmtu=1500 usb0Mode=host nandEcc=1bit ethact=egiga0 bootargs=console=ttyS0,115200 root=/dev/mtdblock2 ro serverip=169.254.254.252 ipaddr=169.254.254.253 ethaddr=00:25:31:00:71:CA cesvcid=PHBFCAYRBRJVGJ4PM69T3KDSH2 ceboardver=PPV2 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial load_uimage=ext2load usb 0:1 0x800000 /boot/uImage load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd usb_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000 usb_bootcmd=run usb_set_bootargs; run usb_boot bootcmd=usb reset; run usb_bootcmd; usb stop; reset Environment size: 1073/131068 bytes
CE>> boot Unknown command 'usb' - try 'help' ** Block device usb 0 not supported ** Block device usb 0 not supported ## Booting image at 00800000 ... Bad Magic Number Unknown command 'usb' - try 'help' U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.100000] Using static partition definition [ 1.110000] Creating 4 MTD partitions on "nand_mtd": [ 1.110000] 0x00000000-0x00100000 : "u-boot" [ 1.120000] 0x00100000-0x00500000 : "uImage" [ 1.120000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 2.120000] usb 1-1.1: new high speed USB device using ehci_marvell and address 3 [ 2.220000] usb 1-1.1: configuration #1 chosen from 1 choice [ 2.220000] usbcore: registered new interface driver usblp [ 2.230000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 2.240000] Initializing USB Mass Storage driver... [ 2.240000] scsi0 : SCSI emulation for USB Mass Storage devices [ 2.250000] usbcore: registered new interface driver usb-storage [ 2.250000] USB Mass Storage support registered. [ 2.260000] mice: PS/2 mouse device common for all mice [ 2.260000] i2c /dev entries driver [ 2.270000] Linux telephony interface: v1.00 [ 2.270000] md: linear personality registered for level -1 [ 2.280000] md: raid0 personality registered for level 0 [ 2.280000] md: raid1 personality registered for level 1 [ 2.460000] raid6: int32x1 97 MB/s [ 2.630000] raid6: int32x2 114 MB/s [ 2.800000] raid6: int32x4 122 MB/s [ 2.970000] raid6: int32x8 110 MB/s [ 2.970000] raid6: using algorithm int32x4 (122 MB/s) [ 2.970000] md: raid6 personality registered for level 6 [ 2.980000] md: raid5 personality registered for level 5 [ 2.980000] md: raid4 personality registered for level 4 [ 2.990000] raid5: measuring checksumming speed [ 3.040000] arm4regs : 1084.000 MB/sec [ 3.090000] 8regs : 754.800 MB/sec [ 3.140000] 32regs : 900.000 MB/sec [ 3.140000] raid5: using function: arm4regs (1084.000 MB/sec) [ 3.150000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 3.150000] dm_crypt using the OCF package. [ 3.160000] sdhci: Secure Digital Host Controller Interface driver [ 3.160000] sdhci: Copyright(c) Pierre Ossman [ 3.170000] usbcore: registered new interface driver usbhid [ 3.170000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 3.180000] TCP cubic registered [ 3.180000] NET: Registered protocol family 1 [ 3.190000] NET: Registered protocol family 17 [ 3.190000] md: Autodetecting RAID arrays. [ 3.200000] md: autorun ... [ 3.200000] md: ... autorun DONE. [ 6.100000] Empty flash at 0x009ac208 ends at 0x009ac800 [ 7.470000] jffs2_scan_eraseblock(): Node at 0x010a07f8 {0x1985, 0xe001, 0x00000032) has invalid CRC 0xffffffff (calculated 0x503776f3) [ 7.480000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x010a07fc: 0x0032 instead [ 9.400000] VFS: Mounted root (jffs2 filesystem) readonly. [ 9.410000] Freeing init memory: 124K [ 9.420000] scsi 0:0:0:0: Direct-Access Kingston SNA-DC/U 1.08 PQ: 0 ANSI: 4 [ 9.470000] sd 0:0:0:0: [sda] 250069680 512-byte hardware sectors (128036 MB) [ 9.480000] sd 0:0:0:0: [sda] Write Protect is off [ 9.480000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 9.510000] sd 0:0:0:0: [sda] 250069680 512-byte hardware sectors (128036 MB) [ 9.520000] sd 0:0:0:0: [sda] Write Protect is off [ 9.520000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 9.530000] sda: sda1 [ 9.630000] sd 0:0:0:0: [sda] Attached SCSI disk [ 9.630000] sd 0:0:0:0: Attached scsi generic sg0 type 0
Re: PogoPlug E02 unusable May 30, 2023 01:04AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: PogoPlug E02 unusable May 31, 2023 02:08AM |
Registered: 1 year ago Posts: 10 |
CE>> bootm 0x800000 0x1100000 ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2023-05-31 5:26:41 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5445938 Bytes = 5.2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-5.13.6-kirkwood-tld-1 Created: 2021-09-24 1:06:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9671027 Bytes = 9.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005317f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: CloudEngines Pogoplug E02 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] INITRD: 0x01100000+0x0093a000 overlaps in-use memory region - disabling initrd [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 240508K/262144K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 21636K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000056][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000931][ T0] Console: colour dummy device 80x30 [ 0.001001][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.001041][ T0] pid_max: default: 32768 minimum: 301 [ 0.001444][ T0] LSM: Security Framework initializing [ 0.001624][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001669][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003096][ T0] CPU: Testing write buffer coherency: ok [ 0.005413][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005707][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.006030][ T1] rcu: Hierarchical SRCU implementation. [ 0.007402][ T1] devtmpfs: initialized [ 0.013061][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.013114][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.050620][ T1] prandom32: self test passed (less than 6 bits correlated) [ 0.050662][ T1] prandom: seed boundary self test passed [ 0.055120][ T1] prandom: 100 self tests passed [ 0.055138][ T1] pinctrl core: initialized pinctrl subsystem [ 0.056743][ T1] NET: Registered protocol family 16 [ 0.057590][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.058601][ T1] audit: initializing netlink subsys (disabled) [ 0.060011][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.060410][ T16] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1 [ 0.060566][ T1] cpuidle: using governor ladder [ 0.060658][ T1] cpuidle: using governor menu [ 0.061160][ T1] Feroceon L2: Enabling L2 [ 0.061212][ T1] Feroceon L2: Cache support initialised. [ 0.069986][ T1] No ATAGs? [ 2.560064][ C0] random: fast init done [ 5.036599][ T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher [ 5.063621][ T59] wait_for_initramfs() called before rootfs_initcalls [ 5.260335][ T1] raid6: int32x8 gen() 107 MB/s [ 5.430278][ T1] raid6: int32x8 xor() 68 MB/s [ 5.600164][ T1] raid6: int32x4 gen() 108 MB/s [ 5.770258][ T1] raid6: int32x4 xor() 70 MB/s [ 5.940165][ T1] raid6: int32x2 gen() 134 MB/s [ 6.110156][ T1] raid6: int32x2 xor() 82 MB/s [ 6.280323][ T1] raid6: int32x1 gen() 97 MB/s [ 6.450280][ T1] raid6: int32x1 xor() 58 MB/s [ 6.450299][ T1] raid6: using algorithm int32x2 gen() 134 MB/s [ 6.450314][ T1] raid6: .... xor() 82 MB/s, rmw enabled [ 6.450327][ T1] raid6: using intx1 recovery algorithm [ 6.450622][ T1] vgaarb: loaded [ 6.451219][ T1] SCSI subsystem initialized [ 6.451791][ T1] usbcore: registered new interface driver usbfs [ 6.451869][ T1] usbcore: registered new interface driver hub [ 6.451932][ T1] usbcore: registered new device driver usb [ 6.452158][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.452175][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.452213][ T1] PTP clock support registered [ 6.454175][ T1] clocksource: Switched to clocksource orion_clocksource [ 6.564875][ T1] VFS: Disk quotas dquot_6.6.0 [ 6.564987][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 6.586388][ T1] NET: Registered protocol family 2 [ 6.586579][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 6.587687][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 6.587744][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.587796][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.587843][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 6.588104][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 6.588190][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 6.588232][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 6.588499][ T1] NET: Registered protocol family 1 [ 6.589284][ T1] RPC: Registered named UNIX socket transport module. [ 6.589307][ T1] RPC: Registered udp transport module. [ 6.589320][ T1] RPC: Registered tcp transport module. [ 6.589332][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 6.589351][ T1] PCI: CLS 0 bytes, default 32 [ 6.589540][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 8.241681][ T1] Initialise system trusted keyrings [ 8.241750][ T1] Key type blacklist registered [ 8.242014][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 8.242161][ T1] zbud: loaded [ 8.243719][ T1] NFS: Registering the id_resolver key type [ 8.243763][ T1] Key type id_resolver registered [ 8.243779][ T1] Key type id_legacy registered [ 8.243826][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 8.243853][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 8.243869][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 8.244156][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 8.244777][ T1] fuse: init (API version 7.34) [ 8.245229][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 8.245465][ T1] orangefs_init: module version upstream loaded [ 8.245486][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 8.346399][ T1] xor: measuring software checksum speed [ 8.355364][ T1] arm4regs : 1113 MB/sec [ 8.370181][ T1] 8regs : 667 MB/sec [ 8.380490][ T1] 32regs : 960 MB/sec [ 8.380510][ T1] xor: using function: arm4regs (1113 MB/sec) [ 8.380534][ T1] async_tx: api initialized (async) [ 8.380555][ T1] Key type asymmetric registered [ 8.380570][ T1] Asymmetric key parser 'x509' registered [ 8.380634][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 8.380716][ T1] io scheduler bfq registered [ 8.580520][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 8.582903][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 8.645389][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.648221][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 8.705377][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.708499][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 8.709942][ T1] printk: console [ttyS0] disabled [ 8.710045][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 9.559193][ T1] printk: console [ttyS0] enabled [ 9.573536][ T1] loop: module loaded [ 9.578479][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 9.585614][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit [ 9.590781][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.599447][ T1] Scanning device for bad blocks [ 9.725115][ T1] 4 cmdlinepart partitions found on MTD device orion_nand [ 9.732117][ T1] Creating 4 MTD partitions on "orion_nand": [ 9.738011][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 9.745316][ T1] 0x000000100000-0x000000500000 : "uImage" [ 9.752541][ T1] 0x000000500000-0x000002500000 : "rootfs" [ 9.759936][ T1] 0x000002500000-0x000008000000 : "data" [ 9.767928][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 9.776551][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 9.788221][ T1] libphy: Fixed MDIO Bus: probed [ 9.794712][ T1] libphy: orion_mdio_bus: probed [ 9.801049][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.565264][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:00:71:ca [ 10.574917][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.582215][ T1] ehci-pci: EHCI PCI platform driver [ 10.587473][ T1] ehci-orion: EHCI orion driver [ 10.592420][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 10.598704][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 10.607315][ T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 10.634223][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.641285][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 10.650328][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.658315][ T1] usb usb1: Product: EHCI Host Controller [ 10.663919][ T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd [ 10.671377][ T1] usb usb1: SerialNumber: f1050000.ehci [ 10.677558][ T1] hub 1-0:1.0: USB hub found [ 10.682086][ T1] hub 1-0:1.0: 1 port detected [ 10.687627][ T1] usbcore: registered new interface driver usb-storage [ 10.694875][ T1] mousedev: PS/2 mouse device common for all mice [ 10.974211][ T17] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 11.175952][ T17] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 11.184917][ T17] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 11.192823][ T17] usb 1-1: Product: USB2.0 Hub [ 11.198437][ T17] hub 1-1:1.0: USB hub found [ 11.203331][ T17] hub 1-1:1.0: 4 ports detected [ 11.524203][ T17] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 11.675826][ T17] usb 1-1.1: New USB device found, idVendor=11b0, idProduct=6298, bcdDevice= 1.08 [ 11.684956][ T17] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.693034][ T17] usb 1-1.1: Product: SNA-DC/U [ 11.698401][ T17] usb 1-1.1: Manufacturer: Kingston [ 11.703483][ T17] usb 1-1.1: SerialNumber: 393834313032353030303231 [ 11.710775][ T17] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 11.718417][ T17] scsi host0: usb-storage 1-1.1:1.0 [ 11.764214][ T1] rtc-mv f1010300.rtc: internal RTC not ticking [ 11.770526][ T1] i2c /dev entries driver [ 11.775458][ T1] device-mapper: uevent: version 1.0.3 [ 11.781098][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 11.790775][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 11.798112][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 11.805495][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 11.812912][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 11.819763][ T1] device-mapper: raid: Loading target version 1.15.1 [ 11.827862][ T1] hid: raw HID events driver (C) Jiri Kosina [ 11.834071][ T1] drop_monitor: Initializing network drop monitor service [ 11.841615][ T1] NET: Registered protocol family 10 [ 11.848231][ T1] Segment Routing with IPv6 [ 11.852620][ T1] RPL Segment Routing with IPv6 [ 11.857542][ T1] NET: Registered protocol family 17 [ 11.862973][ T1] Key type dns_resolver registered [ 11.868574][ T1] registered taskstats version 1 [ 11.873405][ T1] Loading compiled-in X.509 certificates [ 11.879417][ T1] zswap: loaded using pool lzo/zbud [ 11.884930][ T1] Key type ._fscrypt registered [ 11.889671][ T1] Key type .fscrypt registered [ 11.894412][ T1] Key type fscrypt-provisioning registered [ 11.902372][ T1] Key type big_key registered [ 11.911115][ T1] Key type encrypted registered [ 11.919413][ T1] Waiting 10 sec before mounting root device... [ 12.725184][ T7] scsi 0:0:0:0: Direct-Access Kingston SNA-DC/U 1.08 PQ: 0 ANSI: 4 [ 12.735880][ T81] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB) [ 12.744738][ T81] sd 0:0:0:0: [sda] Write Protect is off [ 12.750735][ T81] sd 0:0:0:0: [sda] No Caching mode page found [ 12.756846][ T81] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 12.779747][ T81] sda: sda1 [ 12.785743][ T81] sd 0:0:0:0: [sda] Attached SCSI disk [ 22.244207][ T1] md: Waiting for all devices to be available before autodetect [ 22.251759][ T1] md: If you don't use raid, use raid=noautodetect [ 22.258169][ T1] md: Autodetecting RAID arrays. [ 22.262982][ T1] md: autorun ... [ 22.266508][ T1] md: ... autorun DONE. [ 22.271310][ T1] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6 [ 22.280143][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 22.289332][ T1] 1f00 1024 mtdblock0 [ 22.289345][ T1] (driver?) [ 22.297384][ T1] 1f01 4096 mtdblock1 [ 22.297395][ T1] (driver?) [ 22.305409][ T1] 1f02 32768 mtdblock2 [ 22.305420][ T1] (driver?) [ 22.313389][ T1] 1f03 93184 mtdblock3 [ 22.313399][ T1] (driver?) [ 22.321424][ T1] 0800 125034840 sda [ 22.321437][ T1] driver: sd [ 22.329023][ T1] 0801 125034806 sda1 0b5169b1-f533-43bd-9b6b-efb4c652f3c4 [ 22.329036][ T1] [ 22.339050][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 22.348057][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted 5.13.6-kirkwood-tld-1 #1.0 [ 22.356015][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 22.363018][ T1] [<8010e0a4>] (unwind_backtrace) from [<8010a8ac>] (show_stack+0x10/0x14) [ 22.371522][ T1] [<8010a8ac>] (show_stack) from [<80afddf4>] (panic+0xfc/0x328) [ 22.379154][ T1] [<80afddf4>] (panic) from [<81101ad0>] (mount_block_root+0x1e0/0x26c) [ 22.387392][ T1] [<81101ad0>] (mount_block_root) from [<81101c4c>] (mount_root+0xf0/0x120) [ 22.395972][ T1] [<81101c4c>] (mount_root) from [<81101dc0>] (prepare_namespace+0x144/0x180) [ 22.404727][ T1] [<81101dc0>] (prepare_namespace) from [<811015e4>] (kernel_init_freeable+0x1d0/0x234) [ 22.414354][ T1] [<811015e4>] (kernel_init_freeable) from [<80b091cc>] (kernel_init+0x8/0x118) [ 22.423284][ T1] [<80b091cc>] (kernel_init) from [<80100148>] (ret_from_fork+0x14/0x2c) [ 22.431601][ T1] Exception stack(0x8149ffb0 to 0x8149fff8) [ 22.437376][ T1] ffa0: 00000000 00000000 00000000 00000000 [ 22.446300][ T1] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 22.455218][ T1] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 22.462578][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
NAME MOUNTPOINT LABEL SIZE UUID sdb 119.2G `-sdb1 /media/sdb1 rootfs 119.2G 5ca8600f-8446-49a1-a3ad-36f9ad5c2e26
Re: PogoPlug E02 unusable May 31, 2023 01:12PM |
Registered: 4 years ago Posts: 57 |
Re: PogoPlug E02 unusable May 31, 2023 01:29PM |
Registered: 7 years ago Posts: 369 |
Re: PogoPlug E02 unusable May 31, 2023 01:32PM |
Registered: 7 years ago Posts: 369 |
Re: PogoPlug E02 unusable May 31, 2023 02:44PM |
Admin Registered: 13 years ago Posts: 18,821 |
mkfs.ext3 -L rootfs /dev/sdb1
e2label /dev/sdb1 rootfs
Re: PogoPlug E02 unusable June 01, 2023 01:51AM |
Registered: 1 year ago Posts: 10 |
Change the root=Label=rootfs to root=/dev/sda1 and tftp boot again.
Re: PogoPlug E02 unusable June 01, 2023 11:16AM |
Registered: 7 years ago Posts: 369 |
Re: PogoPlug E02 unusable June 01, 2023 01:14PM |
Admin Registered: 13 years ago Posts: 18,821 |
> Change the root=Label=rootfs to root=/dev/sda1 and > tftp boot again. >>
Re: PogoPlug E02 unusable June 06, 2023 12:34AM |
Registered: 1 year ago Posts: 10 |
root=LABEL=rootfsin setenv bootargs.
mkfs.ext3 -L rootfs /dev/sdb1command above when making the file system.
Re: PogoPlug E02 unusable June 06, 2023 01:17AM |
Registered: 7 years ago Posts: 369 |
Re: PogoPlug E02 unusable June 06, 2023 01:20AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: PogoPlug E02 unusable June 08, 2023 12:05AM |
Registered: 1 year ago Posts: 10 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Initializing devices... starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Loading envs from usb 0... ** File not found /boot/uEnv.txt ** Loading envs from usb 1... ** Bad device usb 1 ** Loading envs from usb 2... ** Bad device usb 2 ** Loading envs from usb 3... ** Bad device usb 3 ** Loading envs from ide 0... ** Bad device ide 0 ** Loading envs from ide 1... ** Bad device ide 1 ** Loading envs from ide 2... ** Bad device ide 2 ** Loading envs from ide 3... ** Bad device ide 3 ** Loading envs from mmc 0... ** Bad device mmc 0 ** Loading envs from mmc 1... ** Bad device mmc 1 ** Loading envs from mmc 2... ** Bad device mmc 2 ** Loading envs from mmc 3... ** Bad device mmc 3 ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 753 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5446002 bytes read in 1054 ms (4.9 MiB/s) loading uInitrd ... 9671091 bytes read in 989 ms (9.3 MiB/s) loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... 10114 bytes read in 3813 ms (2 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.13.6-kirkwood-tld-1 Created: 2023-06-08 3:58:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5445938 Bytes = 5.2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.13.6-kirkwood-tld-1 Created: 2021-09-24 1:06:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9671027 Bytes = 9.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f1d6000, end 0fb0f173 ... OK Loading Device Tree to 0f1d0000, end 0f1d5781 ... OK Using machid 0x831 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: CloudEngines Pogoplug E02 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10 [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 240508K/262144K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 21636K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008609][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.016122][ T0] Console: colour dummy device 80x30 [ 0.021394][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032735][ T0] pid_max: default: 32768 minimum: 301 [ 0.038482][ T0] LSM: Security Framework initializing [ 0.044040][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.052163][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.062143][ T0] CPU: Testing write buffer coherency: ok [ 0.070248][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.077452][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.083719][ T1] rcu: Hierarchical SRCU implementation. [ 0.090735][ T1] devtmpfs: initialized [ 0.100455][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.111167][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.156163][ T1] prandom32: self test passed (less than 6 bits correlated) [ 0.163395][ T1] prandom: seed boundary self test passed [ 0.173235][ T1] prandom: 100 self tests passed [ 0.178065][ T1] pinctrl core: initialized pinctrl subsystem [ 0.185692][ T1] NET: Registered protocol family 16 [ 0.191757][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.200397][ T1] audit: initializing netlink subsys (disabled) [ 0.207948][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.208340][ T16] audit: type=2000 audit(0.190:1): state=initialized audit_enabled=0 res=1 [ 0.223787][ T1] cpuidle: using governor ladder [ 0.228763][ T1] cpuidle: using governor menu [ 0.233912][ T1] Feroceon L2: Enabling L2 [ 0.238244][ T1] Feroceon L2: Cache support initialised. [ 0.252373][ T1] No ATAGs? [ 2.568616][ C0] random: fast init done [ 5.146619][ T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher [ 5.180223][ T59] wait_for_initramfs() called before rootfs_initcalls [ 5.378813][ T1] raid6: int32x8 gen() 108 MB/s [ 5.548749][ T1] raid6: int32x8 xor() 68 MB/s [ 5.718673][ T1] raid6: int32x4 gen() 109 MB/s [ 5.888812][ T1] raid6: int32x4 xor() 71 MB/s [ 6.058617][ T1] raid6: int32x2 gen() 142 MB/s [ 6.228644][ T1] raid6: int32x2 xor() 85 MB/s [ 6.398879][ T1] raid6: int32x1 gen() 97 MB/s [ 6.568752][ T1] raid6: int32x1 xor() 61 MB/s [ 6.573746][ T1] raid6: using algorithm int32x2 gen() 142 MB/s [ 6.579884][ T1] raid6: .... xor() 85 MB/s, rmw enabled [ 6.585395][ T1] raid6: using intx1 recovery algorithm [ 6.591119][ T1] vgaarb: loaded [ 6.595115][ T1] SCSI subsystem initialized [ 6.600155][ T1] usbcore: registered new interface driver usbfs [ 6.606424][ T1] usbcore: registered new interface driver hub [ 6.612562][ T1] usbcore: registered new device driver usb [ 6.618544][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.624256][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.634172][ T1] PTP clock support registered [ 6.640739][ T1] clocksource: Switched to clocksource orion_clocksource [ 6.751448][ T1] VFS: Disk quotas dquot_6.6.0 [ 6.756189][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 6.792037][ T1] NET: Registered protocol family 2 [ 6.797285][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 6.821838][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 6.840798][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.849234][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.880819][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 6.888179][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 6.910850][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 6.918136][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 6.941026][ T1] NET: Registered protocol family 1 [ 6.951064][ T1] RPC: Registered named UNIX socket transport module. [ 6.957723][ T1] RPC: Registered udp transport module. [ 6.970761][ T1] RPC: Registered tcp transport module. [ 6.976191][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.000763][ T1] PCI: CLS 0 bytes, default 32 [ 7.005718][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 8.392115][ T1] Initialise system trusted keyrings [ 8.397334][ T1] Key type blacklist registered [ 8.402399][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 8.409698][ T1] zbud: loaded [ 8.414541][ T1] NFS: Registering the id_resolver key type [ 8.420348][ T1] Key type id_resolver registered [ 8.425333][ T1] Key type id_legacy registered [ 8.430108][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 8.437575][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 8.445767][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 8.453158][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 8.461501][ T1] fuse: init (API version 7.34) [ 8.466651][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 8.474076][ T1] orangefs_init: module version upstream loaded [ 8.480209][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 8.590670][ T1] xor: measuring software checksum speed [ 8.605183][ T1] arm4regs : 1113 MB/sec [ 8.625065][ T1] 8regs : 667 MB/sec [ 8.640316][ T1] 32regs : 971 MB/sec [ 8.645443][ T1] xor: using function: arm4regs (1113 MB/sec) [ 8.651451][ T1] async_tx: api initialized (async) [ 8.656535][ T1] Key type asymmetric registered [ 8.661394][ T1] Asymmetric key parser 'x509' registered [ 8.667052][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 8.675289][ T1] io scheduler bfq registered [ 8.879356][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 8.889739][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 8.951877][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.962623][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.031850][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.042858][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.051405][ T1] printk: console [ttyS0] disabled [ 9.056486][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 9.066334][ T1] printk: console [ttyS0] enabled [ 9.066334][ T1] printk: console [ttyS0] enabled [ 9.076187][ T1] printk: bootconsole [earlycon0] disabled [ 9.076187][ T1] printk: bootconsole [earlycon0] disabled [ 9.096755][ T1] loop: module loaded [ 9.101671][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 9.108773][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit [ 9.113973][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.122616][ T1] Scanning device for bad blocks [ 9.247352][ T1] 4 fixed-partitions partitions found on MTD device orion_nand [ 9.254811][ T1] Creating 4 MTD partitions on "orion_nand": [ 9.260681][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 9.267990][ T1] 0x000000100000-0x000000600000 : "uImage" [ 9.275282][ T1] 0x000000500000-0x000002a00000 : "pogoplug" [ 9.282881][ T1] 0x000002500000-0x000009100000 : "root" [ 9.288406][ T1] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0x5b00000 [ 9.301627][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 9.310206][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 9.321864][ T1] libphy: Fixed MDIO Bus: probed [ 9.328231][ T1] libphy: orion_mdio_bus: probed [ 9.334583][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.081828][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 10.091603][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.098899][ T1] ehci-pci: EHCI PCI platform driver [ 10.104158][ T1] ehci-orion: EHCI orion driver [ 10.109103][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 10.115387][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 10.124000][ T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 10.150782][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.157856][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 10.166899][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.174885][ T1] usb usb1: Product: EHCI Host Controller [ 10.180489][ T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd [ 10.187946][ T1] usb usb1: SerialNumber: f1050000.ehci [ 10.194120][ T1] hub 1-0:1.0: USB hub found [ 10.198646][ T1] hub 1-0:1.0: 1 port detected [ 10.204166][ T1] usbcore: registered new interface driver usb-storage [ 10.211411][ T1] mousedev: PS/2 mouse device common for all mice [ 10.490769][ T17] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 10.692511][ T17] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 10.701469][ T17] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 10.709374][ T17] usb 1-1: Product: USB2.0 Hub [ 10.714986][ T17] hub 1-1:1.0: USB hub found [ 10.719765][ T17] hub 1-1:1.0: 4 ports detected [ 11.040768][ T17] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 11.196381][ T17] usb 1-1.3: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00 [ 11.205509][ T17] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.213597][ T17] usb 1-1.3: Product: Flash Disk [ 11.218422][ T17] usb 1-1.3: Manufacturer: USB [ 11.223090][ T17] usb 1-1.3: SerialNumber: AAAR0R9RFNPMGVTE [ 11.230303][ T17] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 11.237815][ T17] usb-storage 1-1.3:1.0: Quirks match for vid 090c pid 1000: 400 [ 11.245612][ T17] scsi host0: usb-storage 1-1.3:1.0 [ 11.290780][ T1] rtc-mv f1010300.rtc: internal RTC not ticking [ 11.297110][ T1] i2c /dev entries driver [ 11.302020][ T1] device-mapper: uevent: version 1.0.3 [ 11.307665][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 11.317331][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 11.324665][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 11.332049][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 11.339460][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 11.346308][ T1] device-mapper: raid: Loading target version 1.15.1 [ 11.354392][ T1] hid: raw HID events driver (C) Jiri Kosina [ 11.360636][ T1] drop_monitor: Initializing network drop monitor service [ 11.368174][ T1] NET: Registered protocol family 10 [ 11.374771][ T1] Segment Routing with IPv6 [ 11.379166][ T1] RPL Segment Routing with IPv6 [ 11.384086][ T1] NET: Registered protocol family 17 [ 11.389515][ T1] Key type dns_resolver registered [ 11.395107][ T1] registered taskstats version 1 [ 11.399942][ T1] Loading compiled-in X.509 certificates [ 11.405952][ T1] zswap: loaded using pool lzo/zbud [ 11.411468][ T1] Key type ._fscrypt registered [ 11.416209][ T1] Key type .fscrypt registered [ 11.420924][ T1] Key type fscrypt-provisioning registered [ 11.428844][ T1] Key type big_key registered [ 11.437561][ T1] Key type encrypted registered [ 11.445781][ T1] Waiting 10 sec before mounting root device... [ 12.640876][ T7] scsi 0:0:0:0: Direct-Access USB Flash Disk 1100 PQ: 0 ANSI: 6 [ 12.651816][ T80] sd 0:0:0:0: [sda] 121737216 512-byte logical blocks: (62.3 GB/58.0 GiB) [ 12.661047][ T80] sd 0:0:0:0: [sda] Write Protect is off [ 12.667419][ T80] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 12.683937][ T80] sda: sda1 [ 12.691679][ T80] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 21.610771][ T1] md: Waiting for all devices to be available before autodetect [ 21.618304][ T1] md: If you don't use raid, use raid=noautodetect [ 21.624712][ T1] md: Autodetecting RAID arrays. [ 21.629525][ T1] md: autorun ... [ 21.633050][ T1] md: ... autorun DONE. [ 21.638823][ T1] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.759401][ T1] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 21.769649][ T1] VFS: Mounted root (ext3 filesystem) readonly on device 8:1. [ 21.787483][ T1] devtmpfs: mounted [ 21.794308][ T1] Freeing unused kernel memory: 1024K [ 21.800380][ T1] Checked W+X mappings: passed, no W+X pages found [ 21.806828][ T1] Run /sbin/init as init process INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. [ 22.727530][ T171] ecc_sw_hamming_correct: uncorrectable ECC error [ 22.733986][ T171] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 22.745924][ T171] ecc_sw_hamming_correct: uncorrectable ECC error [ 22.752257][ T171] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 22.763646][ T171] Buffer I/O error on dev mtdblock0, logical block 255, async page read Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 25.505670][ T287] orion_wdt: Initial timeout 21 sec [ 26.044217][ T289] usbcore: registered new interface driver uas [ 26.201575][ T288] marvell-cesa f1030000.crypto: CESA device successfully registered [ 26.281983][ T289] sd 0:0:0:0: Attached scsi generic sg0 type 0 done. Setting hostname to 'debian'...done. Not activating swap on swapfile. ... (warning). [ 27.358921][ T438] EXT4-fs (sda1): re-mounted. Opts: (null). Quota mode: none. Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 [ 27.489306][ C0] random: crng init done e2fsck 1.46.2 (28-Feb-2021) rootfs: clean, 15920/3809280 files, 705864/15216896 blocks . [ 27.824362][ T450] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. [ 29.840771][ T732] Adding 524284k swap on /swapfile1. Priority:-2 extents:13 across:7769664k FS Will now mount local filesystems:. Will now activate swapfile swap, if any:swapon: /swapfile1: found signature [pagesize=4096, signature=swap] swapon: /swapfile1: pagesize=4096, swapsize=536870912, devsize=536870912 swapon /swapfile1 done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Initializing random number generator...done. Starting Setting kernel variables: sysctl. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/52:3b:20:9c:11:51 Sending on LPF/eth0/52:3b:20:9c:11:51 Sending on Socket/fallback DHCPREQUEST for 172.16.1.191 on eth0 to 255.255.255.255 port 67 [ 34.423317][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 34.433972][ T95] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST for 172.16.1.191 on eth0 to 255.255.255.255 port 67 DHCPACK of 172.16.1.191 from 172.16.1.224 bound to 172.16.1.191 -- renewal in 234 seconds. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 999 (syslogd) . Starting NFS common utilities: statd idmapd. Starting system message bus: dbus. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Not starting NFS kernel daemon: no exports. ... (warning). Starting NTP server: ntpd. Starting OpenBSD Secure Shell server: sshd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1037 (klogd) . Running local boot scripts (/etc/rc.local) . Debian GNU/Linux 11 debian ttyS0
Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Loading envs from usb 0... ** File not found /boot/uEnv.txt ** Loading envs from usb 1... ** Bad device usb 1 ** Loading envs from usb 2... ** Bad device usb 2 ** Loading envs from usb 3... ** Bad device usb 3 ** Loading envs from ide 0... ** Bad device ide 0 ** Loading envs from ide 1... ** Bad device ide 1 ** Loading envs from ide 2... ** Bad device ide 2 ** Loading envs from ide 3... ** Bad device ide 3 ** Loading envs from mmc 0... ** Bad device mmc 0 ** Loading envs from mmc 1... ** Bad device mmc 1 ** Loading envs from mmc 2... ** Bad device mmc 2 ** Loading envs from mmc 3... ** Bad device mmc 3 **and am wondering what should be done to fix them (or if they need fixing).
Re: PogoPlug E02 unusable June 08, 2023 12:56AM |
Admin Registered: 13 years ago Posts: 18,821 |
> Unknown command 'ide' - try 'help' > Unknown command 'mmc' - try 'help' > Loading envs from usb 0... > ** File not found /boot/uEnv.txt ** > Loading envs from usb 1... > ** Bad device usb 1 ** > Loading envs from usb 2... > ** Bad device usb 2 ** > Loading envs from usb 3... > ** Bad device usb 3 ** > Loading envs from ide 0... > ** Bad device ide 0 ** > Loading envs from ide 1... > ** Bad device ide 1 ** > Loading envs from ide 2... > ** Bad device ide 2 ** > Loading envs from ide 3... > ** Bad device ide 3 ** > Loading envs from mmc 0... > ** Bad device mmc 0 ** > Loading envs from mmc 1... > ** Bad device mmc 1 ** > Loading envs from mmc 2... > ** Bad device mmc 2 ** > Loading envs from mmc 3... > ** Bad device mmc 3 ** >> and am wondering what should be done to fix them
fw_setenv devices usb