Debian on ReadyNas RN2120
Posted by spiderdijon
|
Debian on ReadyNas RN2120 February 22, 2024 06:47AM |
Registered: 2 months ago Posts: 27 |
|
Re: Debian on ReadyNas RN2120 February 22, 2024 01:10PM |
Admin Registered: 13 years ago Posts: 18,575 |
spiderdijon,
Yes, this box is supported in mainline Linux. So I'd expect it can be supported here easily (if the u-boot used in this box is a bit newish).
Let me write a summary of steps to get it to boot Debian in the next post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Yes, this box is supported in mainline Linux. So I'd expect it can be supported here easily (if the u-boot used in this box is a bit newish).
Let me write a summary of steps to get it to boot Debian in the next post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 February 22, 2024 01:43PM |
Admin Registered: 13 years ago Posts: 18,575 |
Booting the MVEBU (Armada 37x, 38x, and XP) boards with stock u-boot.
1. Create the Debian rootfs on a USB stick, using the tarball Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2 (16 Dec 2023) from the Linux Kernel MVEBU package and Debian armhf rootfs release thread. Or use whichever the latest rootfs in the release thread.
In rootfs installation Step 3, the DTB you need to use must be for the box you are installing. For example, the RN2120 box DTB file is armada-xp-netgear-rn2120.dtb.
2. Connect serial console. See here for some suggestion what to buy if it is the first time you do this.
3. Attach the new USB rootfs. Power up the box. Interrupt u-boot at the countdown and,
Warning: do not execute saveenv or resetenv at the u-boot prompt. During testing we want the envs to be original so we can reset the box to the original state where stock OS can be booted.
4. Post the entire serial console log here. Base on what the output looks like, I will post commands to modify u-boot envs (temporarily) to boot into Debian on USB. Note that the setenv commands are transient (see Step 6 below for reseting the box at anytime during testing).
Here are the setenv commands for the Netgear RN2120. Copy and paste each command to the u-boot prompt.
5. Observe serial console. Whether it boots successfully to the Debian prompt or not, please post the entire serial console log here. Entire log (from the u-boot banner) will be needed for troubleshooting, and for verification that everything works in the kernel.
6. Reset the box to boot stock OS
At anytime when you want to abandon the testing session and boot back to stock OS,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/23/2024 03:10PM by bodhi.
1. Create the Debian rootfs on a USB stick, using the tarball Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2 (16 Dec 2023) from the Linux Kernel MVEBU package and Debian armhf rootfs release thread. Or use whichever the latest rootfs in the release thread.
In rootfs installation Step 3, the DTB you need to use must be for the box you are installing. For example, the RN2120 box DTB file is armada-xp-netgear-rn2120.dtb.
2. Connect serial console. See here for some suggestion what to buy if it is the first time you do this.
3. Attach the new USB rootfs. Power up the box. Interrupt u-boot at the countdown and,
help bdinfo printenv usb startAnd then if the USB drive was initialized OK (by usb start),
usb part ext2ls usb 0:1 /boot
Warning: do not execute saveenv or resetenv at the u-boot prompt. During testing we want the envs to be original so we can reset the box to the original state where stock OS can be booted.
4. Post the entire serial console log here. Base on what the output looks like, I will post commands to modify u-boot envs (temporarily) to boot into Debian on USB. Note that the setenv commands are transient (see Step 6 below for reseting the box at anytime during testing).
Here are the setenv commands for the Netgear RN2120. Copy and paste each command to the u-boot prompt.
setenv bootdev usb setenv device 0:1 setenv load_image_addr 0x02000000 setenv load_initrd_addr 0x3000000 setenv load_image 'echo loading uImage ...; ext2load $bootdev $device $load_image_addr /boot/uImage' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial"' setenv bootcmd_exec 'echo Booting Debian from $bootdev; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; bootm $load_image_addr $load_initrd_addr' setenv bootcmd_custom_usb 'usb start; run set_bootargs; run bootcmd_exec' setenv bootcmd 'run bootcmd_custom_usb'and then try booting
boot
5. Observe serial console. Whether it boots successfully to the Debian prompt or not, please post the entire serial console log here. Entire log (from the u-boot banner) will be needed for troubleshooting, and for verification that everything works in the kernel.
6. Reset the box to boot stock OS
At anytime when you want to abandon the testing session and boot back to stock OS,
usb stopand then turn off the power and remove the USB stick. And then power on to boot into stock FW.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/23/2024 03:10PM by bodhi.
|
Re: Debian on ReadyNas RN2120 February 23, 2024 09:45AM |
Registered: 2 months ago Posts: 27 |
Hi Bodhi,
Thanks for replying! Here is the serial console log:
Thanks for replying! Here is the serial console log:
BootROM 1.20
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.8 (COM-PHY-V22)
Update Device ID PEX0782311AB
Update Device ID PEX1782311AB
Update Device ID PEX2782311AB
Update Device ID PEX3782311AB
Update Device ID PEX4782311AB
Update Device ID PEX5782311AB
Update Device ID PEX6782311AB
Update PEX Device ID 0x78230
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run with PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
�
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gd923454 (Sep 08 2015 - 18:59:32) Marvell version: v2011.12 2014_T2.0p1
Netgear version: 09/08/2015 ReadyNAS-2120 v2.0
Board: DB-78460-BP rev 2.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 2 GiB
�
Map: Code: 0x7fedf000:0x7ff9f204
BSS: 0x7ffefc20
Stack: 0x7f9deef8
Heap: 0x7f9df000:0x7fedf000
NAND: 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: Bad block at 0x000005de0000
nand_read_bbt: Bad block at 0x000005e00000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0.0(0-0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1-1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1.0(2-2): Root Complex Interface, Detected Link X1, GEN 2.0
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
Modules Detected:
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Found 2 disks present
Hit any key to stop autoboot: 0
Marvell>>
Marvell>> help
? - alias for 'help'
SatR - Sample At Reset sub-system
active_units- print Board units active
amp_boot- amp_boot - boot an AMP group
amp_config- Fully config an AMP group
amp_printenv- amp_printenv - print only AMP env variables
amp_verify- Verfiy AMP configuration
base - print or set address offset
bdinfo - print Board Info structure
bios - BIOS command to set the DB configuration.
boot - boot default, i.e., run 'bootcmd'
boot_menu- command allows to select boot script from boot device
example: boot_menu
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
bootz - boot Linux zImage image from memory
bubt - bubt - Burn an image on the Boot Flash.
chpart - change active partition
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
date - get/set/reset date & time
ddrPhyRead- ddrPhyRead - Read DDR PHY register
ddrPhyWrite- ddrPhyWrite - Write DDR PHY register
dhcp - boot image via network using DHCP/TFTP protocol
diskboot- diskboot- boot from IDE device
dma - dma - Perform DMA using the XOR engine
echo - echo args to console
editenv - edit environment variable
eeprom - EEPROM sub-system
env - environment handling commands
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
false - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fdt - flattened device tree utility commands
fsinfo - print information about filesystems
fsload - load binary file from a filesystem image
go - start application at address 'addr'
help - print command description/usage
i2c - I2C sub-system
ide - ide - IDE sub-system
iminfo - print header information for application image
imxtract- extract a part of a multi-image
ir - ir - reading and changing MV internal register values.
itest - return true/false on integer compare
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
ls - list files in a directory (default /)
map - map - Display address decode windows
md - memory display
me - me - PCI master enable
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - display MMC info
mp - mp - map PCI BAR
mtdparts- define flash/nand partitions
mtest - simple RAM read/write test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
pciePhyRead- phyRead - Read PCI-E Phy register
pciePhyWrite- pciePhyWrite - Write PCI-E Phy register
phyRead - phyRead - Read Phy register
phyWrite- phyWrite - Write Phy register
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
pxe - commands to get and boot from pxe files
rcvr - rcvr - Satrt recovery process (Distress Beacon with TFTP server)
reset - Perform RESET of the CPU
resetenv- resetenv - Erase environment sector to reset all variables to default.
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
scsi - SCSI sub-system
scsiboot- boot from SCSI device
se - se - PCI Slave enable
setenv - set environment variables
sf - SPI flash sub-system
sg - sg - scanning the PHYs status
showvar - print local hushshell variables
sleep - delay execution for some time
source - run script from memory
sp - scan and detect all devices on mvPCI interface
sramInit- sramInit - Init SRAM memory
sspi - SPI utility command
stage_boot- command to load script/image from different devices
example: stage_boot hd_img pxe
sys_restore- sys_restore - Search for install script on USB DOK and start installation of linux kernel and rootfs.
temp - temp - Display the device temperature.
tempCmd0- tempCmd - This command allocated for monitor extinction
tempCmd1- tempCmd - This command allocated for monitor extinction
tempCmd2- tempCmd - This command allocated for monitor extinction
tempCmd3- tempCmd - This command allocated for monitor extinction
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
training- training - prints the results of the DDR3 Training.
true - do nothing, successfully
ts_report- ts_report - report touch screen coordinate
ts_test - ts_test - test touch screen
ubi - ubi commands
ubifsload- load file from an UBIFS filesystem
ubifsls - list files in a directory
ubifsmount- mount UBIFS volume
ubifsumount- unmount UBIFS volume
usb - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
warmRst - warmRst - Warn Reset AXP card over PEX.
whoAmI - - reading CPU ID
Marvell>> bdinfo
arch_number = 0x00000BDC
boot_params = 0x00000100
DRAM bank = 0x00000000
-> start = 0x00000000
-> size = 0x80000000
DRAM bank = 0x00000001
-> start = 0x00000000
-> size = 0x00000000
DRAM bank = 0x00000002
-> start = 0x00000000
-> size = 0x00000000
DRAM bank = 0x00000003
-> start = 0x00000000
-> size = 0x00000000
ethaddr = 28:C6:8E:35:86:60
ip_addr = 0.0.0.0
baudrate = 115200 bps
TLB addr = 0x7FFF0000
relocaddr = 0x7FEDF000
reloc off = 0x7FEDF000
irq_sp = 0x7F9DEF08
sp start = 0x7F9DEEF8
FB base = 0x00000000
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
MPmode=smp
Manufacturer=NETGEAR
Product=ReadyNAS 2120
SKUNum=RN2120
SerialNum=3GB438E8002B2
Startup=Normal
UUID=d612f834-071c-11e3-b44c-28c68e358660
Version=V1.0
amp_enable=no
autoload=no
boot_order=hd_scr hd_img pxe net_img net_scr
bootargs=console=ttyS0,115200 pm_disable=yes mv_cpu_count=2
bootargs_dflt=$console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel
bootargs_end=:10.4.50.254:255.255.255.0:DSMP:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=nand read 0x2000000 0x200000 0x400000; nand read 0x3000000 0x800000 0x400000; bootm 0x2000000 0x3000000 0x1000000
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disL2Cache=yes
disL2Prefetch=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=no
enaCpuStream=no
enaDCPref=yes
enaFPU=yes
enaICPref=yes
enaLPAE=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=28:C6:8E:35:86:61
eth1mtu=1500
eth2addr=00:50:43:00:00:02
eth2mtu=1500
eth3addr=00:50:43:02:00:00
eth3mtu=1500
ethact=egiga1
ethaddr=28:C6:8E:35:86:60
ethmtu=1500
ethprime=egiga1
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-xp-db.dtb
ide_path=/
image_name=uImage
initrd_name=uInitrd
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:02:00:00
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
setL2CacheWT=no
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=host
usbActive=0
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3080/131068 bytes
Marvell>> usb start
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Marvell>> usb part
Partition Map for USB device 0 -- Partition Type: EFI
Part Name Start LBA End LBA
1 rootfs 0x00000800 0x01CA37FF
Marvell>> ext2ls usb 0:1 /boot
<DIR> 4096 .
<DIR> 4096 ..
<DIR> 4096 dts
5179520 vmlinuz-6.6.2-mvebu-tld-1
23805472 linux-image-6.6.2-mvebu-tld-1_1_armhf.deb
3382390 System.map-6.6.2-mvebu-tld-1
222517 config-6.6.2-mvebu-tld-1
5257109 initrd.img-6.6.2-mvebu-tld-1
5257173 uInitrd
5198457 uImage
8604988 linux-headers-6.6.2-mvebu-tld-1_1_armhf.deb
5179520 zImage-6.6.2-mvebu-tld-1
5179584 uImage.orig
5198393 zImage.fdt
Marvell>>
|
Re: Debian on ReadyNas RN2120 February 23, 2024 01:31PM |
Admin Registered: 13 years ago Posts: 18,575 |
That looks promising. It might take a few tries to get it to boot successfully but should be easy.
I'll write the Steps in a separate post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I'll write the Steps in a separate post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 February 23, 2024 03:15PM |
Admin Registered: 13 years ago Posts: 18,575 |
@spiderdijon,
I've updated Steps 4-6 in the installation post above.
Please try, and post serial console log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I've updated Steps 4-6 in the installation post above.
Please try, and post serial console log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 February 24, 2024 04:38AM |
Registered: 2 months ago Posts: 27 |
Here is the serial console from the boot attempt, it appears to hang at "Starting Kernel ..." with no further serial activity.
BootROM 1.20
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.8 (COM-PHY-V22)
Update Device ID PEX0782311AB
Update Device ID PEX1782311AB
Update Device ID PEX2782311AB
Update Device ID PEX3782311AB
Update Device ID PEX4782311AB
Update Device ID PEX5782311AB
Update Device ID PEX6782311AB
Update PEX Device ID 0x78230
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run with PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
�
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gd923454 (Sep 08 2015 - 18:59:32) Marvell version: v2011.12 2014_T2.0p1
Netgear version: 09/08/2015 ReadyNAS-2120 v2.0
Board: DB-78460-BP rev 2.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 2 GiB
�
Map: Code: 0x7fedf000:0x7ff9f204
BSS: 0x7ffefc20
Stack: 0x7f9deef8
Heap: 0x7f9df000:0x7fedf000
NAND: 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: Bad block at 0x000005de0000
nand_read_bbt: Bad block at 0x000005e00000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0.0(0-0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1-1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1.0(2-2): Root Complex Interface, Detected Link X1, GEN 2.0
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
Modules Detected:
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Found 2 disks present
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>> setenv bootdev usb
Marvell>> setenv device 0:1
Marvell>> setenv load_image_addr 0x02000000
Marvell>> setenv load_initrd_addr 0x3000000
Marvell>> setenv load_image 'echo loading uImage ...; ext2load $bootdev $device $load_image_addr /boot/uImage'
Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd'
Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial"'
Marvell>> setenv bootcmd_exec 'echo Booting Debian from $bootdev; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; bootm $load_image_addr $load_initrd_addr'
Marvell>> setenv bootcmd_custom_usb 'usb start; run set_bootargs; run bootcmd_exec'
Marvell>> setenv bootcmd 'run bootcmd_custom_usb'
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Booting Debian from usb
loading uImage ...
Loading file "/boot/uImage" from usb device 0:1 (rootfs)
5198457 bytes read
loading uInitrd ...
Loading file "/boot/uInitrd" from usb device 0:1 (rootfs)
5257173 bytes read
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-6.6.2-mvebu-tld-1
Created: 2024-02-22 11:59:22 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5198393 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: initramfs-6.6.2-mvebu-tld-1
Created: 2023-12-12 22:03:52 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5257109 Bytes = 5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
|
Re: Debian on ReadyNas RN2120 February 24, 2024 01:51PM |
Admin Registered: 13 years ago Posts: 18,575 |
That bad. It did not survive the decompression.
Let's try this before we go back to stock booting scheme.
Repeat the same setenvs, but with this bootcmd_exec (replace setenv initrd_high 0xffffffff with printenv)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Let's try this before we go back to stock booting scheme.
Repeat the same setenvs, but with this bootcmd_exec (replace setenv initrd_high 0xffffffff with printenv)
setenv bootcmd_exec 'echo Booting Debian from $bootdev; setenv fdt_skip_update yes; printenv; run load_image; run load_initrd; bootm $load_image_addr $load_initrd_addr'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 February 26, 2024 03:56AM |
Registered: 2 months ago Posts: 27 |
Here is the output with the modified bootcmd_exec
ootROM 1.20
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.8 (COM-PHY-V22)
Update Device ID PEX0782311AB
Update Device ID PEX1782311AB
Update Device ID PEX2782311AB
Update Device ID PEX3782311AB
Update Device ID PEX4782311AB
Update Device ID PEX5782311AB
Update Device ID PEX6782311AB
Update PEX Device ID 0x78230
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run with PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
�
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gd923454 (Sep 08 2015 - 18:59:32) Marvell version: v2011.12 2014_T2.0p1
Netgear version: 09/08/2015 ReadyNAS-2120 v2.0
Board: DB-78460-BP rev 2.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 2 GiB
�
Map: Code: 0x7fedf000:0x7ff9f204
BSS: 0x7ffefc20
Stack: 0x7f9deef8
Heap: 0x7f9df000:0x7fedf000
NAND: 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: Bad block at 0x000005de0000
nand_read_bbt: Bad block at 0x000005e00000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0.0(0-0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1-1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1.0(2-2): Root Complex Interface, Detected Link X1, GEN 2.0
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
Modules Detected:
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Found 2 disks present
Hit any key to stop autoboot: 0
Marvell>>
Marvell>> setenv bootdev usb
Marvell>> setenv device 0:1
Marvell>> setenv load_image_addr 0x02000000
Marvell>> setenv load_initrd_addr 0x3000000
Marvell>> setenv load_image 'echo loading uImage ...; ext2load $bootdev $device $load_image_addr /boot/uImage'
Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd'
Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial"'
Marvell>> setenv bootcmd_exec 'echo Booting Debian from $bootdev; setenv fdt_skip_update yes; printenv; run load_image; run load_initrd; bootm $load_image_addr $load_initrd_addr'
Marvell>> setenv bootcmd_custom_usb 'usb start; run set_bootargs; run bootcmd_exec'
Marvell>> setenv bootcmd 'run bootcmd_custom_usb'
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Booting Debian from usb
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
MPmode=smp
Manufacturer=NETGEAR
Product=ReadyNAS 2120
SKUNum=RN2120
SerialNum=3GB438E8002B2
Startup=Normal
UUID=d612f834-071c-11e3-b44c-28c68e358660
Version=V1.0
amp_enable=no
autoload=no
boot_order=hd_scr hd_img pxe net_img net_scr
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
bootargs_dflt=$console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel
bootargs_end=:10.4.50.254:255.255.255.0:DSMP:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=run bootcmd_custom_usb
bootcmd_auto=stage_boot $boot_order
bootcmd_custom_usb=usb start; run set_bootargs; run bootcmd_exec
bootcmd_exec=echo Booting Debian from $bootdev; setenv fdt_skip_update yes; printenv; run load_image; run load_initrd; bootm $load_image_addr $load_initrd_addr
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
bootdev=usb
cacheShare=no
console=console=ttyS0,115200
device=0:1
device_partition=0:1
disL2Cache=yes
disL2Prefetch=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=no
enaCpuStream=no
enaDCPref=yes
enaFPU=yes
enaICPref=yes
enaLPAE=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=28:C6:8E:35:86:61
eth1mtu=1500
eth2addr=00:50:43:00:00:02
eth2mtu=1500
eth3addr=00:50:43:02:00:00
eth3mtu=1500
ethact=egiga1
ethaddr=28:C6:8E:35:86:60
ethmtu=1500
ethprime=egiga1
fdt_addr=2040000
fdt_skip_update=yes
fdtaddr=0x1000000
fdtfile=armada-xp-db.dtb
ide_path=/
image_name=uImage
initrd_name=uInitrd
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
load_image=echo loading uImage ...; ext2load $bootdev $device $load_image_addr /boot/uImage
load_image_addr=0x02000000
load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x3000000
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:02:00:00
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
setL2CacheWT=no
set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial"
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=host
usbActive=0
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3620/131068 bytes
loading uImage ...
Loading file "/boot/uImage" from usb device 0:1 (rootfs)
5198457 bytes read
loading uInitrd ...
Loading file "/boot/uInitrd" from usb device 0:1 (rootfs)
5257173 bytes read
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-6.6.2-mvebu-tld-1
Created: 2024-02-22 11:59:22 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5198393 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: initramfs-6.6.2-mvebu-tld-1
Created: 2023-12-12 22:03:52 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5257109 Bytes = 5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
|
Re: Debian on ReadyNas RN2120 February 26, 2024 03:57PM |
Admin Registered: 13 years ago Posts: 18,575 |
@spiderdijon,
Ah OK. I did not notice that this box has a much older u-boot for Armada XP and Armada 370.
Are you familiar with chroot? you need to install the other kernel on top of the current basic rootfs Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2.
This is the kernel that should be used for this box.
GTI Mirabox and Netgear RN120/RN104 (Armada 370) Installation & Kernel Upgrade (Linux-6.5.7)
https://forum.doozan.com/read.php?2,92514
You can also use use the zImage from kernel linux-6.5.7-mvebu-370xp-tld-1 to boot temporarily into Debian, and then install the full kernel.
Let me know if the above made sense. Please ask question if you are not sure.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Ah OK. I did not notice that this box has a much older u-boot for Armada XP and Armada 370.
Are you familiar with chroot? you need to install the other kernel on top of the current basic rootfs Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2.
This is the kernel that should be used for this box.
GTI Mirabox and Netgear RN120/RN104 (Armada 370) Installation & Kernel Upgrade (Linux-6.5.7)
https://forum.doozan.com/read.php?2,92514
You can also use use the zImage from kernel linux-6.5.7-mvebu-370xp-tld-1 to boot temporarily into Debian, and then install the full kernel.
Let me know if the above made sense. Please ask question if you are not sure.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 February 26, 2024 07:00PM |
Registered: 2 months ago Posts: 27 |
Thanks for your response. It makes some sense but I'm not entirely sure. This is my understanding:
1. recreate the bootable usb drive but with the different kernel you specified above
2. using the same setenv commands above, boot the usb drive
3. Once booted temporarily into debian, install the full kernel (or should this be rootfs which would make sense with chroot?)
Actually yes it seems I'm quite unclear on how to proceed :)
1. recreate the bootable usb drive but with the different kernel you specified above
2. using the same setenv commands above, boot the usb drive
3. Once booted temporarily into debian, install the full kernel (or should this be rootfs which would make sense with chroot?)
Actually yes it seems I'm quite unclear on how to proceed :)
|
Re: Debian on ReadyNas RN2120 February 26, 2024 08:13PM |
Admin Registered: 13 years ago Posts: 18,575 |
spiderdijon,
1. Recreate the bootable usb drive but with the different kernel
Yes. On another Linux host, you can chroot into the USB rootfs (you already created) to install new full kernel linux-6.5.7-mvebu-370xp-tld-1. And then use the same setenv commands above, boot the usb drive.
Or use the alternative where you don't use chroot to install:
2. You can also boot kernel linux-6.5.7-mvebu-370xp-tld-1 temporarily using its zImage
- Mount the already created USB rootfs (with Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2) on another Linux host. Assuming it is mounted at /media/sdb1.
- Download kernel linux-6.5.7-mvebu-370xp-tld-1-bodhi.tar.bz2 tarball to a new folder /media/sdb1/boot/kernel. And extract it.
- And then create a new uImage with kernel zImage-6.5.7-mvebu-370xp-tld-1.
- And umount remove the USB rootfs. Bring it to the RN2120. And boot with the same setenvs commands above.
Once you boot into Debian, you can proceed to install full kernel as described in the release thread.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/27/2024 02:15PM by bodhi.
1. Recreate the bootable usb drive but with the different kernel
Yes. On another Linux host, you can chroot into the USB rootfs (you already created) to install new full kernel linux-6.5.7-mvebu-370xp-tld-1. And then use the same setenv commands above, boot the usb drive.
Or use the alternative where you don't use chroot to install:
2. You can also boot kernel linux-6.5.7-mvebu-370xp-tld-1 temporarily using its zImage
- Mount the already created USB rootfs (with Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2) on another Linux host. Assuming it is mounted at /media/sdb1.
- Download kernel linux-6.5.7-mvebu-370xp-tld-1-bodhi.tar.bz2 tarball to a new folder /media/sdb1/boot/kernel. And extract it.
cd /media/sdb1/boot/kernel tar xf linux-6.5.7-mvebu-370xp-tld-1-bodhi.tar.bz2
- And then create a new uImage with kernel zImage-6.5.7-mvebu-370xp-tld-1.
cd /media/sdb1/boot cp -a ./kernel/zImage-6.5.7-mvebu-370xp-tld-1 zImage.fdt cat dts/armada-xp-netgear-rn2120.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-mvebu-370xp-tld-1 -d zImage.fdt uImage
- And umount remove the USB rootfs. Bring it to the RN2120. And boot with the same setenvs commands above.
Once you boot into Debian, you can proceed to install full kernel as described in the release thread.
Quote
Updated 24 Oct 2023:
Kernel linux-6.5.7-mvebu-370xp-tld-1 package has been uploaded.
New/Updated in this release:
- General kernel upgrade.
Latest Linux kernel 6.x general release information can be found at:
LinuxChanges log
Download at Dropbox
linux-6.5.7-mvebu-370xp-tld-1-bodhi.tar.bz2
md5:
b0f7e62f67c7b198eae0d8e025a54263
sha256sum:
bd478c47e16c201ed2e28c64eab33d7552964170b6d58134549244c38ab810c7
This tarball contains 6 files:
linux-image-6.5.7-mvebu-370xp-tld-1_1_armhf.deb
linux-headers-6.5.7-mvebu-370xp-tld-1_1_armhf.deb
zImage-6.5.7-mvebu-370xp-tld-1
config-6.5.7-mvebu-370xp-tld-1
linux-dtb-6.5.7-mvebu-370xp-tld-1.tar
linux-6.5.7-mvebu-370xp-tld-1.patch
And as always, please verify the hash of what you've downloaded!
Installation
NOTE: the following steps are for a general kernel upgrade. For 1st time installation, please see Initial Installation (scroll down to 06 Sept 2020 section)
1. Backup your current zImage, uImage, and uInitrd. In the /boot directory, these are files for your current kernel (xx.xx.xx is the version number):
uInitrd
uImage
zImage-xx.xx.xx-mvebu-370xp-xxx
initrd.img-xx.xx.xx-mvebu-370xp-xxx
System.map-xx.xx.xx-mvebu-370xp-xxx
vmlinuz-xx.xx.xx-mvebu-370xp-xxx
config-xx.xx.xx-mvebu-370xp-xxx
2. Extract the kernel and the DTB files in the archive:
cd /boot
tar -xjf linux-6.5.7-mvebu-370xp-tld-1-bodhi.tar.bz2
tar -xf linux-dtb-6.5.7-mvebu-370xp-tld-1.tar
3. And install it with dpkg. Remove flash-kernel first to avoid potential problem:
cd /boot
apt-get remove flash-kernel
dpkg -i linux-image-6.5.7-mvebu-370xp-tld-1_1_armhf.deb
4. Create uImage and uInitrd (kernel file initrd.img-6.5.7-mvebu-370xp-tld-1 was generated by dpkg in step 3).
(I'm using the Mirabox armada-370-mirabox.dtb here in the instruction. Please replace DTB name with armada-370-netgear-rn102.dtb or armada-370-netgear-rn104.dtb if you are upgrading the Netgear RN102 or RN104 box).
cd /boot
cp -a uImage uImage.bak
cp -a uInitrd uInitrd.bak
cp -a zImage-6.5.7-mvebu-370xp-tld-1 zImage.fdt
cat dts/armada-370-mirabox.dtb >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-mvebu-370xp-tld-1 -d zImage.fdt uImage
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-6.5.7-mvebu-370xp-tld-1 -d initrd.img-6.5.7-mvebu-370xp-tld-1 uInitrd
5. The new uImage and uInitrd files should be created in /boot directory now. You're ready to reboot the system:
sync
sync
sync
shutdown -r now
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/27/2024 02:15PM by bodhi.
|
Re: Debian on ReadyNas RN2120 February 27, 2024 05:10PM |
Registered: 2 months ago Posts: 27 |
OK great. Thank you for the instructions, they were very clear. I have successfully booted into debian and updated the rootfs and kernel. Here is the log:
It is interesting to note that the RN2120 has a dual core CPU but seemingly only one core is being detected?
Also interesting is the large wait for a PCI device when booting:
Actually looking at how low that device is in the PCI root...could that be the second core?
I assume there should be a way to make the setenv commands permanent? It would also be interesting to know if you know how to allow the second core to be used.
Edited 2 time(s). Last edit at 02/27/2024 05:19PM by spiderdijon.
BootROM 1.20
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.8 (COM-PHY-V22)
Update Device ID PEX0782311AB
Update Device ID PEX1782311AB
Update Device ID PEX2782311AB
Update Device ID PEX3782311AB
Update Device ID PEX4782311AB
Update Device ID PEX5782311AB
Update Device ID PEX6782311AB
Update PEX Device ID 0x78230
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run with PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gd923454 (Sep 08 2015 - 18:59:32) Marvell version: v2011.12 2014_T2.0p1
Netgear version: 09/08/2015 ReadyNAS-2120 v2.0
Board: DB-78460-BP rev 2.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 2 GiB
Map: Code: 0x7fedf000:0x7ff9f204
BSS: 0x7ffefc20
Stack: 0x7f9deef8
Heap: 0x7f9df000:0x7fedf000
NAND: 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: Bad block at 0x000005de0000
nand_read_bbt: Bad block at 0x000005e00000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0.0(0-0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1-1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1.0(2-2): Root Complex Interface, Detected Link X1, GEN 2.0
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
Modules Detected:
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Found 2 disks present
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>> setenv bootdev usb
Marvell>> setenv device 0:1
Marvell>> setenv load_image_addr 0x02000000
Marvell>> setenv load_initrd_addr 0x3000000
Marvell>> setenv load_image 'echo loading uImage ...; ext2load $bootdev $device $load_image_addr /boot/uImage'
Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd'
Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial"'
Marvell>> setenv bootcmd_exec 'echo Booting Debian from $bootdev; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; bootm $load_image_addr $load_initrd_addr'
Marvell>> setenv bootcmd_custom_usb 'usb start; run set_bootargs; run bootcmd_exec'
Marvell>> setenv bootcmd 'run bootcmd_custom_usb'
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Booting Debian from usb
loading uImage ...
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
5043897 bytes read
loading uInitrd ...
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
5275219 bytes read
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-6.5.7-mvebu-370xp-tld-1
Created: 2024-02-27 22:53:24 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5043833 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: initramfs-6.5.7-mvebu-370xp-tld-
Created: 2024-02-27 22:53:48 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5275155 Bytes = 5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.5.7-mvebu-370xp-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Thu Oct 19 18:31:43 PDT 2023
[ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: div instructions available: patching division code
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: NETGEAR ReadyNAS 2120
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000][ T0] ------------[ cut here ]------------
[ 0.000000][ T0] WARNING: CPU: 0 PID: 0 at arch/arm/kernel/devtree.c:130 arm_dt_init_cpu_maps+0xbc/0x158
[ 0.000000][ T0] DT /cpu 2 nodes greater than max cores 1, capping them
[ 0.000000][ T0] Modules linked in:
[ 0.000000][ T0] CPU: 0 PID: 0 Comm: swapper Not tainted 6.5.7-mvebu-370xp-tld-1 #2
[ 0.000000][ T0] Hardware name: Marvell Armada 370/XP (Device Tree)
[ 0.000000][ T0] unwind_backtrace from show_stack+0x10/0x14
[ 0.000000][ T0] show_stack from dump_stack_lvl+0x24/0x2c
[ 0.000000][ T0] dump_stack_lvl from __warn+0x68/0xc4
[ 0.000000][ T0] __warn from warn_slowpath_fmt+0x88/0x114
[ 0.000000][ T0] warn_slowpath_fmt from arm_dt_init_cpu_maps+0xbc/0x158
[ 0.000000][ T0] arm_dt_init_cpu_maps from setup_arch+0x27c/0x4c0
[ 0.000000][ T0] setup_arch from start_kernel+0x4c/0x874
[ 0.000000][ T0] start_kernel from 0x0
[ 0.000000][ T0] ---[ end trace 0000000000000000 ]---
[ 0.000000][ T0] CPU: All CPU(s) started in SVC mode.
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) reason=normal bdtype=rn2120
[ 0.000000][ T0] Unknown kernel command line parameters "reason=normal bdtype=rn2120", will be passed to user space.
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 2053888K/2097152K available (10240K kernel code, 853K rwdata, 3416K rodata, 1024K init, 464K bss, 43264K reserved, 0K cma-reserved, 1310708K highmem)
[ 0.000000][ T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a69ef10 -> 0x1a69ef12
[ 0.000000][ T0] Aurora cache controller enabled, 32 ways, 2048 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a69ef12
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns
[ 0.000001][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.008497][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.020624][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval)
[ 0.030201][ T0] Console: colour dummy device 80x30
[ 0.035354][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.046368][ T0] CPU: Testing write buffer coherency: ok
[ 0.051988][ T0] pid_max: default: 32768 minimum: 301
[ 0.061696][ T0] LSM: initializing lsm=capability,integrity
[ 0.068486][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.076478][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.090419][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.098248][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.106605][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.113784][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.119715][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.126716][ T1] rcu: Hierarchical SRCU implementation.
[ 0.132203][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.139601][ T1] devtmpfs: initialized
[ 0.149908][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.158668][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.169169][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.178045][ T1] prandom: seed boundary self test passed
[ 0.186125][ T1] prandom: 100 self tests passed
[ 0.190907][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.198546][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.205599][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.215819][ T1] audit: initializing netlink subsys (disabled)
[ 0.222729][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.222789][ T1] cpuidle: using governor ladder
[ 0.234251][ T19] audit: type=2000 audit(0.200:1): state=initialized audit_enabled=0 res=1
[ 0.242694][ T1] cpuidle: using governor menu
[ 0.247473][ T1] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.257174][ T1] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.268033][ T1] platform soc: Fixed dependency cycle(s) with /soc/internal-regs/interrupt-controller@20a00
[ 0.450066][ T1] raid6: int32x8 gen() 230 MB/s
[ 0.620075][ T1] raid6: int32x4 gen() 248 MB/s
[ 0.790103][ T1] raid6: int32x2 gen() 391 MB/s
[ 0.960105][ T1] raid6: int32x1 gen() 374 MB/s
[ 0.965054][ T1] raid6: using algorithm int32x2 gen() 391 MB/s
[ 1.140061][ T1] raid6: .... xor() 220 MB/s, rmw enabled
[ 1.145614][ T1] raid6: using intx1 recovery algorithm
[ 1.152210][ T1] SCSI subsystem initialized
[ 1.157046][ T1] usbcore: registered new interface driver usbfs
[ 1.163274][ T1] usbcore: registered new interface driver hub
[ 1.169320][ T1] usbcore: registered new device driver usb
[ 1.175419][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.181069][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.190882][ T1] PTP clock support registered
[ 1.197378][ T1] vgaarb: loaded
[ 1.201328][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 1.213235][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.218027][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.237233][ T1] NET: Registered PF_INET protocol family
[ 1.242993][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.252730][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.261963][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.270387][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.278858][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.286721][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.294134][ T1] MPTCP token hash table entries: 1024 (order: 1, 12288 bytes, linear)
[ 1.302359][ T1] UDP hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 1.309571][ T1] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 1.317673][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.324510][ T1] RPC: Registered named UNIX socket transport module.
[ 1.331102][ T1] RPC: Registered udp transport module.
[ 1.336519][ T1] RPC: Registered tcp transport module.
[ 1.341910][ T1] RPC: Registered tcp-with-tls transport module.
[ 1.348064][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.355186][ T1] PCI: CLS 0 bytes, default 64
[ 1.360001][ T12] Trying to unpack rootfs image as initramfs...
[ 1.366536][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 1.393679][ T1] Initialise system trusted keyrings
[ 1.398855][ T1] Key type blacklist registered
[ 1.411536][ T1] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 1.418720][ T1] zbud: loaded
[ 1.452728][ T1] NFS: Registering the id_resolver key type
[ 1.458495][ T1] Key type id_resolver registered
[ 1.471373][ T1] Key type id_legacy registered
[ 1.476194][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.491380][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.677087][ T1] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 1.701467][ T1] xor: measuring software checksum speed
[ 1.731756][ T1] arm4regs : 1253 MB/sec
[ 1.751355][ T1] 8regs : 909 MB/sec
[ 1.781352][ T1] 32regs : 1138 MB/sec
[ 1.786392][ T1] xor: using function: arm4regs (1253 MB/sec)
[ 1.793641][ T12] Freeing initrd memory: 5152K
[ 1.800683][ T1] async_tx: api initialized (async)
[ 1.805771][ T1] Key type asymmetric registered
[ 1.810548][ T1] Asymmetric key parser 'x509' registered
[ 1.816533][ T1] bounce: pool size: 64 pages
[ 1.821705][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 1.830005][ T1] io scheduler bfq registered
[ 1.838616][ T1] armada-xp-pinctrl d0018000.pin-ctrl: registered pinctrl driver
[ 1.851093][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 1.862632][ T1] debugfs: Directory 'd0018100.gpio' with parent 'regmap' already present!
[ 1.872596][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 1.882922][ T1] debugfs: Directory 'd0018140.gpio' with parent 'regmap' already present!
[ 1.893093][ T1] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges:
[ 1.901206][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0040000..0x00d0041fff -> 0x0000040000
[ 1.911796][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0044000..0x00d0045fff -> 0x0000044000
[ 1.921005][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0048000..0x00d0049fff -> 0x0000048000
[ 1.930400][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d004c000..0x00d004dfff -> 0x000004c000
[ 1.939743][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0080000..0x00d0081fff -> 0x0000080000
[ 1.948988][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 1.958729][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 1.968464][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 1.978195][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 1.987927][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 1.997657][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 2.007388][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 2.017118][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 2.026852][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0500000000
[ 2.036596][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0500000000
[ 2.047231][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[ 2.054849][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.061019][ T1] pci_bus 0000:00: root bus resource [mem 0xd0040000-0xd0041fff] (bus address [0x00040000-0x00041fff])
[ 2.071887][ T1] pci_bus 0000:00: root bus resource [mem 0xd0044000-0xd0045fff] (bus address [0x00044000-0x00045fff])
[ 2.082749][ T1] pci_bus 0000:00: root bus resource [mem 0xd0048000-0xd0049fff] (bus address [0x00048000-0x00049fff])
[ 2.093605][ T1] pci_bus 0000:00: root bus resource [mem 0xd004c000-0xd004dfff] (bus address [0x0004c000-0x0004dfff])
[ 2.104464][ T1] pci_bus 0000:00: root bus resource [mem 0xd0080000-0xd0081fff] (bus address [0x00080000-0x00081fff])
[ 2.115338][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 2.122901][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 3.401341][ T1] pci 0000:00:01.0: not ready after 1023ms; waiting
[ 4.511341][ T1] pci 0000:00:01.0: not ready after 2047ms; waiting
[ 6.591341][ T1] pci 0000:00:01.0: not ready after 4095ms; waiting
[ 10.751341][ T1] pci 0000:00:01.0: not ready after 8191ms; waiting
[ 19.071341][ T1] pci 0000:00:01.0: not ready after 16383ms; waiting
[ 35.711341][ T1] pci 0000:00:01.0: not ready after 32767ms; waiting
[ 68.991349][ T1] pci 0000:00:01.0: not ready after 65535ms; giving up
[ 68.998146][ T1] pci 0000:00:02.0: [11ab:7823] type 01 class 0x060400
[ 69.005575][ T1] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400
[ 69.014294][ T1] PCI: bus0: Fast back to back transfers disabled
[ 69.020555][ T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 69.029705][ T1] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 69.038690][ T1] pci 0000:01:00.0: [1b4b:9170] type 00 class 0x010601
[ 69.045666][ T1] pci 0000:01:00.0: reg 0x10: [io 0xfffffff8-0xffffffff]
[ 69.052655][ T1] pci 0000:01:00.0: reg 0x14: [io 0xfffffffc-0xffffffff]
[ 69.059602][ T1] pci 0000:01:00.0: reg 0x18: [io 0xfffffff8-0xffffffff]
[ 69.066626][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xfffffffc-0xffffffff]
[ 69.073598][ T1] pci 0000:01:00.0: reg 0x20: [io 0xfffffff0-0xffffffff]
[ 69.080544][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x42000000-0x420001ff]
[ 69.087515][ T1] pci 0000:01:00.0: reg 0x30: [mem 0xd0000000-0xd000ffff pref]
[ 69.094930][ T1] pci 0000:01:00.0: Enabling fixed DMA alias to 00.1
[ 69.101495][ T1] pci 0000:01:00.0: PME# supported from D3hot
[ 69.107799][ T1] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[ 69.141438][ T1] PCI: bus1: Fast back to back transfers disabled
[ 69.147686][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 69.155301][ T1] pci 0000:02:00.0: [1b73:1009] type 00 class 0x0c0330
[ 69.162234][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x48000000-0x4800ffff 64bit]
[ 69.169706][ T1] pci 0000:02:00.0: reg 0x18: [mem 0x48010000-0x48010fff 64bit]
[ 69.177209][ T1] pci 0000:02:00.0: reg 0x20: [mem 0x48011000-0x48011fff 64bit]
[ 69.184766][ T1] pci 0000:02:00.0: supports D1
[ 69.189457][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold
[ 69.196923][ T1] pci 0000:00:05.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[ 69.231398][ T1] PCI: bus2: Fast back to back transfers disabled
[ 69.237655][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 69.245056][ T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[ 69.252637][ T1] pci 0000:00:05.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff]
[ 69.260184][ T1] pci 0000:00:02.0: BAR 13: assigned [io 0x10000-0x10fff]
[ 69.267262][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xf8000000-0xf800ffff pref]
[ 69.275169][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xf8010000-0xf80101ff]
[ 69.282642][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f]
[ 69.289584][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017]
[ 69.296536][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f]
[ 69.303488][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023]
[ 69.310430][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027]
[ 69.317383][ T1] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 69.323035][ T1] pci 0000:00:02.0: bridge window [io 0x10000-0x10fff]
[ 69.329982][ T1] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 69.337463][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf810ffff 64bit]
[ 69.345459][ T1] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8110000-0xf8110fff 64bit]
[ 69.353475][ T1] pci 0000:02:00.0: BAR 4: assigned [mem 0xf8111000-0xf8111fff 64bit]
[ 69.361473][ T1] pci 0000:00:05.0: PCI bridge to [bus 02]
[ 69.367118][ T1] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff]
[ 69.374724][ T1] pcieport 0000:00:02.0: enabling device (0140 -> 0143)
[ 69.381628][ T1] pcieport 0000:00:05.0: enabling device (0140 -> 0142)
[ 69.389585][ T1] mv_xor d0060900.xor: Marvell shared XOR driver
[ 69.452816][ T1] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 69.464317][ T1] mv_xor d00f0900.xor: Marvell shared XOR driver
[ 69.532940][ T1] mv_xor d00f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 69.749506][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 69.766562][ T1] printk: console [ttyS0] disabled
[ 69.796992][ T1] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 30, base_baud = 15625000) is a 16550A
[ 69.806918][ T1] printk: console [ttyS0] enabled
[ 69.806918][ T1] printk: console [ttyS0] enabled
[ 69.816858][ T1] printk: bootconsole [earlycon0] disabled
[ 69.816858][ T1] printk: bootconsole [earlycon0] disabled
[ 69.833487][ T1] ahci 0000:01:00.0: enabling device (0146 -> 0147)
[ 69.840213][ T1] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 69.851010][ T1] ahci 0000:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 69.862864][ T1] scsi host0: ahci
[ 69.867996][ T1] scsi host1: ahci
[ 69.872427][ T1] ata1: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010100 irq 32
[ 69.880466][ T1] ata2: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010180 irq 32
[ 69.889673][ T1] sata_mv d00a0000.sata: slots 32 ports 2
[ 69.899852][ T1] scsi host2: sata_mv
[ 69.905057][ T1] scsi host3: sata_mv
[ 69.909194][ T1] ata3: SATA max UDMA/133 irq 33
[ 69.914810][ T1] ata4: SATA max UDMA/133 irq 33
[ 69.920641][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 69.929038][ T1] nand: Hynix H27U1G8F2BTR-BC
[ 69.933714][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 69.942460][ T1] Bad block table found at page 65472, version 0x01
[ 69.949250][ T1] Bad block table found at page 65408, version 0x01
[ 69.955920][ T1] nand_read_bbt: bad block at 0x000005de0000
[ 69.961794][ T1] nand_read_bbt: bad block at 0x000005e00000
[ 69.967718][ T1] 5 fixed-partitions partitions found on MTD device pxa3xx_nand-0
[ 69.975422][ T1] Creating 5 MTD partitions on "pxa3xx_nand-0":
[ 69.981552][ T1] 0x000000000000-0x000000180000 : "u-boot"
[ 69.989029][ T1] 0x000000180000-0x0000001a0000 : "u-boot-env"
[ 69.997718][ T1] 0x000000200000-0x000000800000 : "uImage"
[ 70.006141][ T1] 0x000000800000-0x000000c00000 : "minirootfs"
[ 70.014926][ T1] 0x000000c00000-0x000008000000 : "ubifs"
[ 70.024892][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 70.035530][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 70.093439][ T1] mvneta d0070000.ethernet eth0: Using random mac address e6:1e:5f:7c:88:e1
[ 70.107060][ T1] mvneta d0074000.ethernet eth1: Using random mac address 16:d5:a9:50:e2:ae
[ 70.118145][ T1] usbcore: registered new interface driver smsc75xx
[ 70.125951][ T1] orion-ehci d0050000.usb: EHCI Host Controller
[ 70.132602][ T1] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1
[ 70.141063][ T1] orion-ehci d0050000.usb: irq 37, io mem 0xd0050000
[ 70.171348][ T1] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00
[ 70.178271][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 70.187311][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 70.195297][ T1] usb usb1: Product: EHCI Host Controller
[ 70.200922][ T1] usb usb1: Manufacturer: Linux 6.5.7-mvebu-370xp-tld-1 ehci_hcd
[ 70.208555][ T1] usb usb1: SerialNumber: d0050000.usb
[ 70.214718][ T1] hub 1-0:1.0: USB hub found
[ 70.219693][ T1] hub 1-0:1.0: 1 port detected
[ 70.224388][ T674] ata1: SATA link down (SStatus 0 SControl 300)
[ 70.232025][ T1] usbcore: registered new interface driver usblp
[ 70.239642][ T679] ata2: SATA link down (SStatus 0 SControl 300)
[ 70.246059][ T1] usbcore: registered new interface driver usb-storage
[ 70.252845][ T695] ata3: SATA link down (SStatus 0 SControl F300)
[ 70.260056][ T1] mousedev: PS/2 mouse device common for all mice
[ 70.268407][ T1] i2c_dev: i2c /dev entries driver
[ 70.275722][ T1] mv64xxx_i2c d0011000.i2c: can't get pinctrl, bus recovery not supported
[ 70.287423][ T1] rtc-ds1307 0-0068: 'wakeup-source' is set, request for an IRQ is disabled!
[ 70.299167][ T1] rtc-ds1307 0-0068: registered as rtc0
[ 70.305885][ T1] rtc-ds1307 0-0068: setting system clock to 2024-02-27T22:58:27 UTC (1709074707)
[ 70.419278][ T1] orion_wdt: Initial timeout 171 sec
[ 70.426254][ T1] device-mapper: uevent: version 1.0.3
[ 70.432574][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 70.442364][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 70.449617][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 70.457140][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 70.464582][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 70.472821][ T1] sdhci: Secure Digital Host Controller Interface driver
[ 70.479724][ T1] sdhci: Copyright(c) Pierre Ossman
[ 70.485865][ T1] sdhci-pltfm: SDHCI platform and OF driver helper
[ 70.497589][ T1] marvell-cesa d0090000.crypto: CESA device successfully registered
[ 70.505991][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 70.511911][ T100] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 70.520854][ T1] usbcore: registered new interface driver usbhid
[ 70.527940][ T1] usbhid: USB HID core driver
[ 70.533694][ T1] NET: Registered PF_INET6 protocol family
[ 70.541066][ T1] Segment Routing with IPv6
[ 70.545548][ T1] RPL Segment Routing with IPv6
[ 70.550328][ T1] In-situ OAM (IOAM) with IPv6
[ 70.555103][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 70.563631][ T1] NET: Registered PF_PACKET protocol family
[ 70.570272][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 70.575283][ T1] Key type dns_resolver registered
[ 70.580567][ T1] ThumbEE CPU extension supported.
[ 70.585618][ T1] Registering SWP/SWPB emulation handler
[ 70.606366][ T700] ata4: SATA link down (SStatus 0 SControl F300)
[ 70.689610][ T1] registered taskstats version 1
[ 70.695129][ T1] Loading compiled-in X.509 certificates
[ 70.713152][ T1] Key type .fscrypt registered
[ 70.717795][ T1] Key type fscrypt-provisioning registered
[ 70.723709][ T1] Key type big_key registered
[ 70.734323][ T100] usb 1-1: New USB device found, idVendor=05dc, idProduct=c75c, bcdDevice= 1.02
[ 70.750768][ T100] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 70.771024][ T100] usb 1-1: Product: USB Flash Drive
[ 70.776254][ T1] Key type encrypted registered
[ 70.785346][ T100] usb 1-1: Manufacturer: Lexar
[ 70.789990][ T100] usb 1-1: SerialNumber: 20131017233031296A5A
[ 70.797159][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 70.807005][ T1] clk: Disabling unused clocks
[ 70.811744][ T100] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 70.822493][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 70.829536][ T100] scsi host4: usb-storage 1-1:1.0
[ 70.838444][ T1] Checked W+X mappings: passed, no W+X pages found
[ 70.844881][ T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.19-1~deb12u1
[ 71.873508][ T10] scsi 4:0:0:0: Direct-Access Lexar USB Flash Drive 8.07 PQ: 0 ANSI: 4
[ 71.896093][ T12] sd 4:0:0:0: [sda] 15351808 512-byte logical blocks: (7.86 GB/7.32 GiB)
[ 71.912338][ T12] sd 4:0:0:0: [sda] Write Protect is off
[ 71.931380][ T12] sd 4:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 71.957633][ T12] sda: sda1
[ 71.963357][ T12] sd 4:0:0:0: [sda] Attached SCSI removable disk
[ 72.581183][ T1274] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead.
[ 72.600420][ T1275] usbcore: registered new interface driver uas
[ 72.626742][ T1276] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead.
[ 72.637311][ T1286] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead.
[ 72.655823][ T1284] mtdblock: MTD device 'minirootfs' is NAND, please consider using UBI block devices instead.
[ 72.668145][ T1272] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead.
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 26769/480496 files, 290426/1918720 blocks
done.
[ 83.870224][ T1305] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 83.931202][ T1305] EXT4-fs (sda1): mounted filesystem fc59c260-6003-47cc-a825-1bf226996f9b ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 87.553443][ T1492] lm75 0-004c: supply vs not found, using dummy regulator
[ 87.644418][ T1487] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead.
[ 87.678886][ T1488] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead.
[ 87.709308][ T1492] hwmon hwmon4: temp1_input not attached to any thermal zone
[ 87.772247][ T1492] lm75 0-004c: hwmon4: sensor 'g751'
[ 87.798090][ T1495] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead.
[ 87.808506][ T1496] mtdblock: MTD device 'minirootfs' is NAND, please consider using UBI block devices instead.
[ 87.921799][ T1485] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead.
[ 88.048307][ T1489] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 88.070391][ T1492] sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 88.148395][ T1489] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 88.300529][ T1489] xhci_hcd 0000:02:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[ 88.483558][ T1489] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 88.578597][ T1489] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 88.733487][ T1489] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 88.820217][ T1489] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 88.920087][ T1489] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 89.067693][ T1489] usb usb2: Product: xHCI Host Controller
[ 89.129721][ T1489] usb usb2: Manufacturer: Linux 6.5.7-mvebu-370xp-tld-1 xhci-hcd
[ 89.171505][ T1489] usb usb2: SerialNumber: 0000:02:00.0
[ 89.272870][ T1489] hub 2-0:1.0: USB hub found
[ 89.353828][ T1489] hub 2-0:1.0: 2 ports detected
[ 89.447746][ T1489] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 89.527313][ T1489] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.05
[ 89.608035][ T1489] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 89.678434][ T1489] usb usb3: Product: xHCI Host Controller
[ 89.729547][ T1489] usb usb3: Manufacturer: Linux 6.5.7-mvebu-370xp-tld-1 xhci-hcd
[ 89.797170][ T1489] usb usb3: SerialNumber: 0000:02:00.0
[ 89.853656][ T1489] hub 3-0:1.0: USB hub found
[ 89.896992][ T1489] hub 3-0:1.0: 2 ports detected
done.
Activating swap:.
[ 90.662462][ T1647] EXT4-fs (sda1): re-mounted fc59c260-6003-47cc-a825-1bf226996f9b r/w. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp
.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
[ 92.581358][ C0] random: crng init done
Initializing random number generator...done.
[ 93.031461][ T2037] mvneta d0070000.ethernet eth0: PHY [d0072004.mdio-mii:00] driver [Marvell 88E1318S] (irq=POLL)
[ 93.055246][ T2037] mvneta d0070000.ethernet eth0: configuring for phy/rgmii-id link mode
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
[ 96.191871][ T905] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPOFFER of 10.11.12.76 from 10.11.12.1
DHCPREQUEST for 10.11.12.76 on eth0 to 255.255.255.255 port 67
DHCPACK of 10.11.12.76 from 10.11.12.1
bound to 10.11.12.76 -- renewal in 3443 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2189 (syslogd)
.
Starting periodic command scheduler: cron.
Starting NTP server: ntpd2024-02-27T14:59:02 ntpd[2242]: INIT: ntpd ntpsec-1.2.2: Starting
2024-02-27T14:59:02 ntpd[2242]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:109
.
Starting NTP server: ntpd.
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2216 (klogd)
.
Running local boot scripts (/etc/rc.local)
Cannot read environment, using default
Cannot read default environment from file
<13>Feb 27 14:59:04 root[2279]: Cannot read u-boot env ethaddr
.
Debian GNU/Linux 12 debian ttyS0
debian login: root
Password:
Linux debian 6.5.7-mvebu-370xp-tld-1 #2 PREEMPT Thu Oct 19 18:31:43 PDT 2023 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Tue Feb 27 14:49:40 PST 2024 on ttyS0
debian
10.11.12.76
NETGEAR ReadyNAS 2120
Linux version 6.5.7-mvebu-370xp-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Thu Oct 19 18:31:43 PDT 2023
Debian 12.4
Tue Feb 27 14:59:10 PST 2024 up 1 minute
root@debian:~#
It is interesting to note that the RN2120 has a dual core CPU but seemingly only one core is being detected?
root@debian:~# cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 2 (v7l) BogoMIPS : 50.00 Features : half thumb fastmult vfp edsp thumbee vfpv3 tls idiva idivt vfpd32 lpae CPU implementer : 0x56 CPU architecture: 7 CPU variant : 0x2 CPU part : 0x584 CPU revision : 2 Hardware : Marvell Armada 370/XP (Device Tree) Revision : 0000 Serial : 0000000000000000 root@debian:~#
Also interesting is the large wait for a PCI device when booting:
[ 3.401341][ T1] pci 0000:00:01.0: not ready after 1023ms; waiting [ 4.511341][ T1] pci 0000:00:01.0: not ready after 2047ms; waiting [ 6.591341][ T1] pci 0000:00:01.0: not ready after 4095ms; waiting [ 10.751341][ T1] pci 0000:00:01.0: not ready after 8191ms; waiting [ 19.071341][ T1] pci 0000:00:01.0: not ready after 16383ms; waiting [ 35.711341][ T1] pci 0000:00:01.0: not ready after 32767ms; waiting [ 68.991349][ T1] pci 0000:00:01.0: not ready after 65535ms; giving up
Actually looking at how low that device is in the PCI root...could that be the second core?
I assume there should be a way to make the setenv commands permanent? It would also be interesting to know if you know how to allow the second core to be used.
Edited 2 time(s). Last edit at 02/27/2024 05:19PM by spiderdijon.
|
Re: Debian on ReadyNas RN2120 February 27, 2024 06:25PM |
Admin Registered: 13 years ago Posts: 18,575 |
spiderdijon,
> OK great. Thank you for the instructions, they
> were very clear. I have successfully booted into
> debian and updated the rootfs and kernel. Here is
> the log:
Cool!
It sounds like you've used option number 2 (boot new kernel temporarily)?
> It is interesting to note that the RN2120 has a
> dual core CPU but seemingly only one core is being
> detected?
> It would also be interesting
> to know if you know how to allow the second core
> to be used.
The issue is: to improve performance for the Mirabox, and RN102/104, I've configured this kernel as a single core (i.e. non-SMP). That's why you are seeing only 1 core.
I would need to put SMP back in this kernel to accomodate this box. I think that would be reasonable, unless there is real performance degradation for the Netgear RN102/104 (I don't care much about the Mirabox, it only good to be used as a test bed for this kernel).
So I will release another version with SMP. And let you install it. And Trond (tme) to test it to see if we can live with SMP kernel on Netgear RN102/104.
> I assume there should be a way to make the setenv
> commands permanent?
Yes. After you test boot a few times, you can save the envs. However, we need to test it to be sure that it won't corrupt the envs by saving. We don't know much about this u-boot version yet so must be careful.
1. Run kwboot to boot this box with another Armada XP u-boot. I had built a version here before I have to find it. Or I can rebuild it and let you try. As long as it can boot to the u-boot count down, then we have a rescue path.
2. If that does not work. We need to make the mtds and u-boot envs accessible in Debian. This is a task to complete for this box any way.
While in Debian , we can dump u-boot image from flash. And use it in kwboot.
3. Once kwboot is working, you can proceed to test saving the envs. If all goes well, the box will automatically boot to USB rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/27/2024 06:29PM by bodhi.
> OK great. Thank you for the instructions, they
> were very clear. I have successfully booted into
> debian and updated the rootfs and kernel. Here is
> the log:
Cool!
It sounds like you've used option number 2 (boot new kernel temporarily)?
> It is interesting to note that the RN2120 has a
> dual core CPU but seemingly only one core is being
> detected?
> It would also be interesting
> to know if you know how to allow the second core
> to be used.
The issue is: to improve performance for the Mirabox, and RN102/104, I've configured this kernel as a single core (i.e. non-SMP). That's why you are seeing only 1 core.
I would need to put SMP back in this kernel to accomodate this box. I think that would be reasonable, unless there is real performance degradation for the Netgear RN102/104 (I don't care much about the Mirabox, it only good to be used as a test bed for this kernel).
So I will release another version with SMP. And let you install it. And Trond (tme) to test it to see if we can live with SMP kernel on Netgear RN102/104.
> I assume there should be a way to make the setenv
> commands permanent?
Yes. After you test boot a few times, you can save the envs. However, we need to test it to be sure that it won't corrupt the envs by saving. We don't know much about this u-boot version yet so must be careful.
1. Run kwboot to boot this box with another Armada XP u-boot. I had built a version here before I have to find it. Or I can rebuild it and let you try. As long as it can boot to the u-boot count down, then we have a rescue path.
2. If that does not work. We need to make the mtds and u-boot envs accessible in Debian. This is a task to complete for this box any way.
While in Debian , we can dump u-boot image from flash. And use it in kwboot.
3. Once kwboot is working, you can proceed to test saving the envs. If all goes well, the box will automatically boot to USB rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/27/2024 06:29PM by bodhi.
|
Re: Debian on ReadyNas RN2120 February 27, 2024 06:46PM |
Admin Registered: 13 years ago Posts: 18,575 |
spiderdijon ,
Please try kwboot with the attached u-boot image: uboot.2024.04-rc3-tld-1.ds414.kwb
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Please try kwboot with the attached u-boot image: uboot.2024.04-rc3-tld-1.ds414.kwb
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 February 29, 2024 05:42AM |
Registered: 2 months ago Posts: 27 |
I'm actually having great difficulty in getting kwboot to work. I have tried several systems including a raspberry pi and it never gets past a few percent:
Rpi using usb serial dongle
On a x86 linux machine I get a similar problem but with a different message:
I should note that both the rpi serial port and the usb serial dongle on all systems can receive the uboot console prints when the rn2120 boots normally.
I have also tried lower and higher baud rates with much the same outcome.
I have tried setting the -a flag for amarda XP timings but then it never seems to even start. Do you have any pointers on what to set -q -s -o to if anything?
Edited 3 time(s). Last edit at 02/29/2024 05:52AM by spiderdijon.
Rpi using usb serial dongle
root@poepi:/home/pi# root@poepi:/home/pi# kwboot -b uboot.2024.04-rc3-tld-1.ds414.kwb -t /dev/ttyUSB0 -p kwboot version 2023.01 Patching image boot signature to UART Aligning image header to Xmodem block size Sending boot message. Please reboot the target...| Sending boot image header (86272 bytes)... 0 % [......................................................................] 10 % [................................E xmodem: Protocol errorRpi using its internal UART:
root@poepi:/home/pi# kwboot -b uboot.2024.04-rc3-tld-1.ds414.kwb -t /dev/serial0 -p -B 115200 kwboot version 2023.01 Patching image boot signature to UART Aligning image header to Xmodem block size Sending boot message. Please reboot the target.../ Sending boot image header (86272 bytes)... 0 % [+++++++++++ xmodem: Input/output error
On a x86 linux machine I get a similar problem but with a different message:
xmodem: Bad message
I should note that both the rpi serial port and the usb serial dongle on all systems can receive the uboot console prints when the rn2120 boots normally.
I have also tried lower and higher baud rates with much the same outcome.
I have tried setting the -a flag for amarda XP timings but then it never seems to even start. Do you have any pointers on what to set -q -s -o to if anything?
Edited 3 time(s). Last edit at 02/29/2024 05:52AM by spiderdijon.
|
Re: Debian on ReadyNas RN2120 February 29, 2024 12:39PM |
Registered: 2 months ago Posts: 27 |
|
Re: Debian on ReadyNas RN2120 February 29, 2024 02:02PM |
Admin Registered: 13 years ago Posts: 18,575 |
Quote
I have tried setting the -a flag for amarda XP timings but then it never seems to even start. Do you have any pointers on what to set -q -s -o to if anything?
That option -a was tested extensively, so -q -s probably will not be much help. And yes, option -a should be used.
Quote
I've read a few threads relating to kwboot. Possibly I might be having a issue because I'm starting kwboot first and then powering on the NAS? Is there a suggested sequence?
No, that's only applicable to the initial handshake. Here you have gone past that, and kwboot already started transfering data.
Quote
root@poepi:/home/pi# root@poepi:/home/pi# kwboot -b uboot.2024.04-rc3-tld-1.ds414.kwb -t /dev/ttyUSB0 -p
kwboot version 2023.01
Patching image boot signature to UART
Aligning image header to Xmodem block size
Sending boot message. Please reboot the target...|
Sending boot image header (86272 bytes)...
0 % [......................................................................]
10 % [................................E
xmodem: Protocol error
Quote
I should note that both the rpi serial port and the usb serial dongle on all systems can receive the uboot console prints when the rn2120 boots normally.
The fact that you can interrupted u-boot count down and boot into Debian proved the serial console works. However, different protocols are use in a normal serial console (i.e. with minicom/picocom/screen) and kwboot. xmodem is a bit more fragile.
Try these:
- Make sure that the serial wires are away from any power source. Sometime the interference can cause noise that messes up the xmodem protocol.
- When seeing "xmodem: Protocol error", up arrow to recall the kwboot command and execute again immediately. Try this as many times as you can.
=====
As I recalled there were more works done for kwboot during the last year. The last maintainer is a very smart guy. I'll build the latest kwboot ARM version to see if it will help.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 February 29, 2024 04:09PM |
Admin Registered: 13 years ago Posts: 18,575 |
spiderdijon,
I've uploaded the latest kwboot in this post:
https://forum.doozan.com/read.php?3,27280,27280#msg-27280
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I've uploaded the latest kwboot in this post:
https://forum.doozan.com/read.php?3,27280,27280#msg-27280
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 February 29, 2024 08:18PM |
Admin Registered: 13 years ago Posts: 18,575 |
Set up MTD partitions and u-boot envs for Debian
Recap. The current setenvs to boot Debian
Add mtdparts and modify set_bootargs commands:
And then boot
Log in to Debian, check the mdts
nano /etc/fw_env.config
Please post the serial log here.
If everything goes well, we can dump mtd0 and use the image for kwboot. More about this in a separate post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/29/2024 11:48PM by bodhi.
Recap. The current setenvs to boot Debian
Marvell>> setenv bootdev usb Marvell>> setenv device 0:1 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_initrd_addr 0x3000000 Marvell>> setenv load_image 'echo loading uImage ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial"' Marvell>> setenv bootcmd_exec 'echo Booting Debian from $bootdev; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; bootm $load_image_addr $load_initrd_addr' Marvell>> setenv bootcmd_custom_usb 'usb start; run set_bootargs; run bootcmd_exec' Marvell>> setenv bootcmd 'run bootcmd_custom_usb'
Add mtdparts and modify set_bootargs commands:
setenv mtdparts 'mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)' setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial"'
And then boot
boot
Log in to Debian, check the mdts
cat /proc/mtdand then edit /etc/fw_env.config file. Its content should be as followed:
nano /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0 0x20000 0x20000And get the listing of the envs
fw_printenv
Please post the serial log here.
If everything goes well, we can dump mtd0 and use the image for kwboot. More about this in a separate post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/29/2024 11:48PM by bodhi.
|
Re: Debian on ReadyNas RN2120 March 01, 2024 04:57AM |
Registered: 2 months ago Posts: 27 |
I'm having difficulty executing the binary on the pi. I think it's due to an incompatible glibc. Could you link the repo where the kwboot development work is going on so I can compile it from source?
Edit: I think I found it: https://source.denx.de/u-boot/u-boot/ (?) but now having difficulty in producing a kwboot binary. It doesn't seem to build it with the "make tools-only"?
Many thanks!
Edited 1 time(s). Last edit at 03/01/2024 09:02AM by spiderdijon.
Edit: I think I found it: https://source.denx.de/u-boot/u-boot/ (?) but now having difficulty in producing a kwboot binary. It doesn't seem to build it with the "make tools-only"?
Many thanks!
Edited 1 time(s). Last edit at 03/01/2024 09:02AM by spiderdijon.
|
Re: Debian on ReadyNas RN2120 March 01, 2024 08:58AM |
Registered: 2 months ago Posts: 27 |
Switching from trying kwboot (I got it to 20% once in about 100 tries!), this is the console log from modifying the envs:
Just to be sure the /.etc/fw_env.config file had a number 4 under "Number of sectors". In your post it is blank. I have blanked it in mine also.
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0 0x20000 0x20000 root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00180000 00020000 "u-boot" mtd1: 00020000 00020000 "u-boot-env" mtd2: 00600000 00020000 "uImage" mtd3: 00400000 00020000 "minirootfs" mtd4: 07400000 00020000 "ubifs" root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0 0x20000 0x20000 root@debian:~# fw_printenv AC_Power_fail_detect=open CASset=min HW_version=MVT MALLOC_len=5 MPmode=smp Manufacturer=NETGEAR Product=ReadyNAS 2120 SKUNum=RN2120 SerialNum=3GB438E8002B2 Startup=Normal UUID=d612f834-071c-11e3-b44c-28c68e358660 Version=V1.0 amp_enable=no autoload=no boot_order=hd_scr hd_img pxe net_img net_scr bootargs=console=ttyS0,115200 pm_disable=yes mv_cpu_count=2 bootargs_dflt=$console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:DSMP:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x200000 0x400000; nand read 0x3000000 0x800000 0x400000; bootm 0x2000000 0x3000000 0x1000000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000 bootdelay=0 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disL2Cache=yes disL2Prefetch=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaCpuStream=no enaDCPref=yes enaFPU=yes enaICPref=yes enaLPAE=no enaMonExt=no enaWrAllo=no envver=3 eth1addr=28:C6:8E:35:86:61 eth1mtu=1500 eth2addr=00:50:43:00:00:02 eth2mtu=1500 eth3addr=00:50:43:02:00:00 eth3mtu=1500 ethact=egiga1 ethaddr=28:C6:8E:35:86:60 ethmtu=1500 ethprime=egiga1 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-xp-db.dtb ide_path=/ image_name=uImage initrd_name=uInitrd kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x02000000 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:02:00:00 nandEcc=1bit netbsd_en=no netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rcvrip=169.254.100.100 sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr setL2CacheWT=no standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=host usbActive=0 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 root@debian:~#
Just to be sure the /.etc/fw_env.config file had a number 4 under "Number of sectors". In your post it is blank. I have blanked it in mine also.
|
Re: Debian on ReadyNas RN2120 March 01, 2024 01:48PM |
Admin Registered: 13 years ago Posts: 18,575 |
> Edit: I think I found it:
> https://source.denx.de/u-boot/u-boot/ (?) but now
> having difficulty in producing a kwboot binary. It
> doesn't seem to build it with the "make
> tools-only"?
>
You need to pick a board first, any ARM board is OK. For example, on rPi:
And thanks for reporting the problem running on rPi. I think I will build a static kwboot and upload it later.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/01/2024 03:20PM by bodhi.
> https://source.denx.de/u-boot/u-boot/ (?) but now
> having difficulty in producing a kwboot binary. It
> doesn't seem to build it with the "make
> tools-only"?
>
You need to pick a board first, any ARM board is OK. For example, on rPi:
make rpi_3_defconfig make tools
And thanks for reporting the problem running on rPi. I think I will build a static kwboot and upload it later.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/01/2024 03:20PM by bodhi.
|
Re: Debian on ReadyNas RN2120 March 01, 2024 01:52PM |
Admin Registered: 13 years ago Posts: 18,575 |
spiderdijon,
> root@debian:~# cat /proc/mtd
> dev: size erasesize name
> mtd0: 00180000 00020000 "u-boot"
> mtd1: 00020000 00020000 "u-boot-env"
> mtd2: 00600000 00020000 "uImage"
> mtd3: 00400000 00020000 "minirootfs"
> mtd4: 07400000 00020000 "ubifs"
Looks good.
> root@debian:~# fw_printenv
Looks good.
> Just to be sure the /.etc/fw_env.config file had a
> number 4 under "Number of sectors". In your post
> it is blank. I have blanked it in mine also.
It's OK. That number is optional.
Please post either the serial log or dmesg output here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> root@debian:~# cat /proc/mtd
> dev: size erasesize name
> mtd0: 00180000 00020000 "u-boot"
> mtd1: 00020000 00020000 "u-boot-env"
> mtd2: 00600000 00020000 "uImage"
> mtd3: 00400000 00020000 "minirootfs"
> mtd4: 07400000 00020000 "ubifs"
Looks good.
> root@debian:~# fw_printenv
Looks good.
> Just to be sure the /.etc/fw_env.config file had a
> number 4 under "Number of sectors". In your post
> it is blank. I have blanked it in mine also.
It's OK. That number is optional.
Please post either the serial log or dmesg output here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 March 02, 2024 03:35AM |
Registered: 2 months ago Posts: 27 |
Here is the full serial log with all commands entered:
Edited 1 time(s). Last edit at 03/02/2024 03:36AM by spiderdijon.
BootROM 1.20
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.8 (COM-PHY-V22)
Update Device ID PEX0782311AB
Update Device ID PEX1782311AB
Update Device ID PEX2782311AB
Update Device ID PEX3782311AB
Update Device ID PEX4782311AB
Update Device ID PEX5782311AB
Update Device ID PEX6782311AB
Update PEX Device ID 0x78230
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run with PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gd923454 (Sep 08 2015 - 18:59:32) Marvell version: v2011.12 2014_T2.0p1
Netgear version: 09/08/2015 ReadyNAS-2120 v2.0
Board: DB-78460-BP rev 2.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 2 GiB
Map: Code: 0x7fedf000:0x7ff9f204
BSS: 0x7ffefc20
Stack: 0x7f9deef8
Heap: 0x7f9df000:0x7fedf000
NAND: 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: Bad block at 0x000005de0000
nand_read_bbt: Bad block at 0x000005e00000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0.0(0-0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1-1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1.0(2-2): Root Complex Interface, Detected Link X1, GEN 2.0
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
Modules Detected:
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Found 2 disks present
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>> setenv bootdev usb
Marvell>> setenv device 0:1
Marvell>> setenv load_imagr 0x02000000
Marvell>> setenv load_init000000
Marvell>>
BootROM 1.20
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.8 (COM-PHY-V22)
Update Device ID PEX0782311AB
Update Device ID PEX1782311AB
Update Device ID PEX2782311AB
Update Device ID PEX3782311AB
Update Device ID PEX4782311AB
Update Device ID PEX5782311AB
Update Device ID PEX6782311AB
Update PEX Device ID 0x78230
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run with PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gd923454 (Sep 08 2015 - 18:59:32) Marvell version: v2011.12 2014_T2.0p1
Netgear version: 09/08/2015 ReadyNAS-2120 v2.0
Board: DB-78460-BP rev 2.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 2 GiB
▒
Map: Code: 0x7fedf000:0x7ff9f204
BSS: 0x7ffefc20
Stack: 0x7f9deef8
Heap: 0x7f9df000:0x7fedf000
NAND: 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: Bad block at 0x000005de0000
nand_read_bbt: Bad block at 0x000005e00000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0.0(0-0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1-1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1.0(2-2): Root Complex Interface, Detected Link X1, GEN 2.0
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
Modules Detected:
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Found 2 disks present
Hit any key to stop autoboot: 0
Marvell>> setenv bootdev usb
Marvell>> setenv device 0:1
Marvell>> setenv load_image_addr 0x02000000
Marvell>> setenv load_initrd_addr 0x3000000
Marvell>> setenv load_image 'echo loading uImage ...; ext2load $bootdev $device $load_image_addr /boot/uImage'
Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd'
Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial"'
Marvell>> setenv bootcmd_exec 'echo Booting Debian from $bootdev; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; bootm $load_image_addr $load_initrd_addr'
Marvell>> setenv bootcmd_custom_usb 'usb start; run set_bootargs; run bootcmd_exec'
Marvell>> setenv bootcmd 'run bootcmd_custom_usb'
Marvell>> setenv mtdparts 'mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)'
Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial"'
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Booting Debian from usb
loading uImage ...
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
5043897 bytes read
loading uInitrd ...
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
5275219 bytes read
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-6.5.7-mvebu-370xp-tld-1
Created: 2024-02-27 22:53:24 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5043833 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: initramfs-6.5.7-mvebu-370xp-tld-
Created: 2024-02-27 22:53:48 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5275155 Bytes = 5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.5.7-mvebu-370xp-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Thu Oct 19 18:31:43 PDT 2023
[ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: div instructions available: patching division code
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: NETGEAR ReadyNAS 2120
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000][ T0] ------------[ cut here ]------------
[ 0.000000][ T0] WARNING: CPU: 0 PID: 0 at arch/arm/kernel/devtree.c:130 arm_dt_init_cpu_maps+0xbc/0x158
[ 0.000000][ T0] DT /cpu 2 nodes greater than max cores 1, capping them
[ 0.000000][ T0] Modules linked in:
[ 0.000000][ T0] CPU: 0 PID: 0 Comm: swapper Not tainted 6.5.7-mvebu-370xp-tld-1 #2
[ 0.000000][ T0] Hardware name: Marvell Armada 370/XP (Device Tree)
[ 0.000000][ T0] unwind_backtrace from show_stack+0x10/0x14
[ 0.000000][ T0] show_stack from dump_stack_lvl+0x24/0x2c
[ 0.000000][ T0] dump_stack_lvl from __warn+0x68/0xc4
[ 0.000000][ T0] __warn from warn_slowpath_fmt+0x88/0x114
[ 0.000000][ T0] warn_slowpath_fmt from arm_dt_init_cpu_maps+0xbc/0x158
[ 0.000000][ T0] arm_dt_init_cpu_maps from setup_arch+0x27c/0x4c0
[ 0.000000][ T0] setup_arch from start_kernel+0x4c/0x874
[ 0.000000][ T0] start_kernel from 0x0
[ 0.000000][ T0] ---[ end trace 0000000000000000 ]---
[ 0.000000][ T0] CPU: All CPU(s) started in SVC mode.
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) earlyprintk=serial mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) reason=normal bdtype=rn2120
[ 0.000000][ T0] Unknown kernel command line parameters "reason=normal bdtype=rn2120", will be passed to user space.
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 2053888K/2097152K available (10240K kernel code, 853K rwdata, 3416K rodata, 1024K init, 464K bss, 43264K reserved, 0K cma-reserved, 1310708K highmem)
[ 0.000000][ T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a696b10 -> 0x1a696b12
[ 0.000000][ T0] Aurora cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns
[ 0.000001][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.008497][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.020621][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval)
[ 0.030198][ T0] Console: colour dummy device 80x30
[ 0.035350][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.046364][ T0] CPU: Testing write buffer coherency: ok
[ 0.051985][ T0] pid_max: default: 32768 minimum: 301
[ 0.061694][ T0] LSM: initializing lsm=capability,integrity
[ 0.068484][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.076476][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.090425][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.098254][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.106609][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.113789][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.119719][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.126719][ T1] rcu: Hierarchical SRCU implementation.
[ 0.132206][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.139606][ T1] devtmpfs: initialized
[ 0.150021][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.158764][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.169279][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.178160][ T1] prandom: seed boundary self test passed
[ 0.186240][ T1] prandom: 100 self tests passed
[ 0.191022][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.198675][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.205770][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.215980][ T1] audit: initializing netlink subsys (disabled)
[ 0.222895][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.222958][ T1] cpuidle: using governor ladder
[ 0.234420][ T19] audit: type=2000 audit(0.200:1): state=initialized audit_enabled=0 res=1
[ 0.242863][ T1] cpuidle: using governor menu
[ 0.247665][ T1] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.257367][ T1] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.268244][ T1] platform soc: Fixed dependency cycle(s) with /soc/internal-regs/interrupt-controller@20a00
[ 0.450075][ T1] raid6: int32x8 gen() 230 MB/s
[ 0.620075][ T1] raid6: int32x4 gen() 248 MB/s
[ 0.790105][ T1] raid6: int32x2 gen() 391 MB/s
[ 0.960108][ T1] raid6: int32x1 gen() 374 MB/s
[ 0.965057][ T1] raid6: using algorithm int32x2 gen() 391 MB/s
[ 1.140067][ T1] raid6: .... xor() 220 MB/s, rmw enabled
[ 1.145620][ T1] raid6: using intx1 recovery algorithm
[ 1.152247][ T1] SCSI subsystem initialized
[ 1.157093][ T1] usbcore: registered new interface driver usbfs
[ 1.163323][ T1] usbcore: registered new interface driver hub
[ 1.169369][ T1] usbcore: registered new device driver usb
[ 1.175468][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.181119][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.190932][ T1] PTP clock support registered
[ 1.197458][ T1] vgaarb: loaded
[ 1.201452][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 1.213397][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.218190][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.237414][ T1] NET: Registered PF_INET protocol family
[ 1.243188][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.252959][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.262197][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.270622][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.279093][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.286956][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.294376][ T1] MPTCP token hash table entries: 1024 (order: 1, 12288 bytes, linear)
[ 1.302604][ T1] UDP hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 1.309817][ T1] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 1.317920][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.324773][ T1] RPC: Registered named UNIX socket transport module.
[ 1.331366][ T1] RPC: Registered udp transport module.
[ 1.336784][ T1] RPC: Registered tcp transport module.
[ 1.342175][ T1] RPC: Registered tcp-with-tls transport module.
[ 1.348330][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.355452][ T1] PCI: CLS 0 bytes, default 64
[ 1.360276][ T12] Trying to unpack rootfs image as initramfs...
[ 1.366884][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 1.394344][ T1] Initialise system trusted keyrings
[ 1.399516][ T1] Key type blacklist registered
[ 1.411698][ T1] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 1.418914][ T1] zbud: loaded
[ 1.452894][ T1] NFS: Registering the id_resolver key type
[ 1.458673][ T1] Key type id_resolver registered
[ 1.471504][ T1] Key type id_legacy registered
[ 1.476335][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.491514][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.692756][ T1] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 1.711513][ T1] xor: measuring software checksum speed
[ 1.741871][ T1] arm4regs : 1253 MB/sec
[ 1.761474][ T1] 8regs : 909 MB/sec
[ 1.789300][ T12] Freeing initrd memory: 5152K
[ 1.793955][ T1] 32regs : 1138 MB/sec
[ 1.798991][ T1] xor: using function: arm4regs (1253 MB/sec)
[ 1.807371][ T1] async_tx: api initialized (async)
[ 1.812480][ T1] Key type asymmetric registered
[ 1.817257][ T1] Asymmetric key parser 'x509' registered
[ 1.823223][ T1] bounce: pool size: 64 pages
[ 1.828207][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 1.836875][ T1] io scheduler bfq registered
[ 1.845308][ T1] armada-xp-pinctrl d0018000.pin-ctrl: registered pinctrl driver
[ 1.857816][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 1.869322][ T1] debugfs: Directory 'd0018100.gpio' with parent 'regmap' already present!
[ 1.878910][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 1.889615][ T1] debugfs: Directory 'd0018140.gpio' with parent 'regmap' already present!
[ 1.899786][ T1] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges:
[ 1.909268][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0040000..0x00d0041fff -> 0x0000040000
[ 1.918556][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0044000..0x00d0045fff -> 0x0000044000
[ 1.927963][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0048000..0x00d0049fff -> 0x0000048000
[ 1.937210][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d004c000..0x00d004dfff -> 0x000004c000
[ 1.946458][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0080000..0x00d0081fff -> 0x0000080000
[ 1.955679][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 1.965412][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 1.975144][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 1.984875][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 1.994607][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 2.004338][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 2.014068][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 2.023802][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 2.033554][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0500000000
[ 2.043282][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0500000000
[ 2.053932][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[ 2.061307][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.067730][ T1] pci_bus 0000:00: root bus resource [mem 0xd0040000-0xd0041fff] (bus address [0x00040000-0x00041fff])
[ 2.078601][ T1] pci_bus 0000:00: root bus resource [mem 0xd0044000-0xd0045fff] (bus address [0x00044000-0x00045fff])
[ 2.089463][ T1] pci_bus 0000:00: root bus resource [mem 0xd0048000-0xd0049fff] (bus address [0x00048000-0x00049fff])
[ 2.100319][ T1] pci_bus 0000:00: root bus resource [mem 0xd004c000-0xd004dfff] (bus address [0x0004c000-0x0004dfff])
[ 2.111177][ T1] pci_bus 0000:00: root bus resource [mem 0xd0080000-0xd0081fff] (bus address [0x00080000-0x00081fff])
[ 2.122053][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 2.129598][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 3.411464][ T1] pci 0000:00:01.0: not ready after 1023ms; waiting
[ 4.511463][ T1] pci 0000:00:01.0: not ready after 2047ms; waiting
[ 6.591463][ T1] pci 0000:00:01.0: not ready after 4095ms; waiting
[ 10.751463][ T1] pci 0000:00:01.0: not ready after 8191ms; waiting
[ 19.071464][ T1] pci 0000:00:01.0: not ready after 16383ms; waiting
[ 35.711463][ T1] pci 0000:00:01.0: not ready after 32767ms; waiting
[ 68.991472][ T1] pci 0000:00:01.0: not ready after 65535ms; giving up
[ 68.998271][ T1] pci 0000:00:02.0: [11ab:7823] type 01 class 0x060400
[ 69.005711][ T1] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400
[ 69.014477][ T1] PCI: bus0: Fast back to back transfers disabled
[ 69.020739][ T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 69.029915][ T1] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 69.038882][ T1] pci 0000:01:00.0: [1b4b:9170] type 00 class 0x010601
[ 69.045869][ T1] pci 0000:01:00.0: reg 0x10: [io 0xfffffff8-0xffffffff]
[ 69.052860][ T1] pci 0000:01:00.0: reg 0x14: [io 0xfffffffc-0xffffffff]
[ 69.059807][ T1] pci 0000:01:00.0: reg 0x18: [io 0xfffffff8-0xffffffff]
[ 69.066829][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xfffffffc-0xffffffff]
[ 69.073801][ T1] pci 0000:01:00.0: reg 0x20: [io 0xfffffff0-0xffffffff]
[ 69.080747][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x42000000-0x420001ff]
[ 69.087718][ T1] pci 0000:01:00.0: reg 0x30: [mem 0xd0000000-0xd000ffff pref]
[ 69.095134][ T1] pci 0000:01:00.0: Enabling fixed DMA alias to 00.1
[ 69.101700][ T1] pci 0000:01:00.0: PME# supported from D3hot
[ 69.108006][ T1] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[ 69.141560][ T1] PCI: bus1: Fast back to back transfers disabled
[ 69.147817][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 69.155419][ T1] pci 0000:02:00.0: [1b73:1009] type 00 class 0x0c0330
[ 69.162357][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x48000000-0x4800ffff 64bit]
[ 69.169829][ T1] pci 0000:02:00.0: reg 0x18: [mem 0x48010000-0x48010fff 64bit]
[ 69.177333][ T1] pci 0000:02:00.0: reg 0x20: [mem 0x48011000-0x48011fff 64bit]
[ 69.184889][ T1] pci 0000:02:00.0: supports D1
[ 69.189580][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold
[ 69.197051][ T1] pci 0000:00:05.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[ 69.231520][ T1] PCI: bus2: Fast back to back transfers disabled
[ 69.237776][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 69.245178][ T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[ 69.252759][ T1] pci 0000:00:05.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff]
[ 69.260308][ T1] pci 0000:00:02.0: BAR 13: assigned [io 0x10000-0x10fff]
[ 69.267386][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xf8000000-0xf800ffff pref]
[ 69.275293][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xf8010000-0xf80101ff]
[ 69.282765][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f]
[ 69.289706][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017]
[ 69.296659][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f]
[ 69.303611][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023]
[ 69.310553][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027]
[ 69.317506][ T1] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 69.323157][ T1] pci 0000:00:02.0: bridge window [io 0x10000-0x10fff]
[ 69.330104][ T1] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 69.337585][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf810ffff 64bit]
[ 69.345582][ T1] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8110000-0xf8110fff 64bit]
[ 69.353598][ T1] pci 0000:02:00.0: BAR 4: assigned [mem 0xf8111000-0xf8111fff 64bit]
[ 69.361596][ T1] pci 0000:00:05.0: PCI bridge to [bus 02]
[ 69.367241][ T1] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff]
[ 69.374852][ T1] pcieport 0000:00:02.0: enabling device (0140 -> 0143)
[ 69.381759][ T1] pcieport 0000:00:05.0: enabling device (0140 -> 0142)
[ 69.389739][ T1] mv_xor d0060900.xor: Marvell shared XOR driver
[ 69.453060][ T1] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 69.464475][ T1] mv_xor d00f0900.xor: Marvell shared XOR driver
[ 69.533104][ T1] mv_xor d00f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 69.750794][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 69.768276][ T1] printk: console [ttyS0] disabled
[ 69.798793][ T1] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 30, base_baud = 15625000) is a 16550A
[ 69.808725][ T1] printk: console [ttyS0] enabled
[ 69.808725][ T1] printk: console [ttyS0] enabled
[ 69.818660][ T1] printk: bootconsole [earlycon0] disabled
[ 69.818660][ T1] printk: bootconsole [earlycon0] disabled
[ 69.852747][ T1] ahci 0000:01:00.0: enabling device (0146 -> 0147)
[ 69.859462][ T1] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 69.870888][ T1] ahci 0000:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 69.882810][ T1] scsi host0: ahci
[ 69.887944][ T1] scsi host1: ahci
[ 69.892393][ T1] ata1: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010100 irq 32
[ 69.900432][ T1] ata2: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010180 irq 32
[ 69.909732][ T1] sata_mv d00a0000.sata: slots 32 ports 2
[ 69.919932][ T1] scsi host2: sata_mv
[ 69.925114][ T1] scsi host3: sata_mv
[ 69.929252][ T1] ata3: SATA max UDMA/133 irq 33
[ 69.934920][ T1] ata4: SATA max UDMA/133 irq 33
[ 69.940786][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 69.949211][ T1] nand: Hynix H27U1G8F2BTR-BC
[ 69.953892][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 69.962593][ T1] Bad block table found at page 65472, version 0x01
[ 69.969383][ T1] Bad block table found at page 65408, version 0x01
[ 69.976054][ T1] nand_read_bbt: bad block at 0x000005de0000
[ 69.981930][ T1] nand_read_bbt: bad block at 0x000005e00000
[ 69.987847][ T1] 5 cmdlinepart partitions found on MTD device pxa3xx_nand-0
[ 69.995111][ T1] Creating 5 MTD partitions on "pxa3xx_nand-0":
[ 70.001229][ T1] 0x000000000000-0x000000180000 : "u-boot"
[ 70.008737][ T1] 0x000000180000-0x0000001a0000 : "u-boot-env"
[ 70.017500][ T1] 0x000000200000-0x000000800000 : "uImage"
[ 70.025927][ T1] 0x000000800000-0x000000c00000 : "minirootfs"
[ 70.034685][ T1] 0x000000c00000-0x000008000000 : "ubifs"
[ 70.044671][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 70.055385][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 70.113252][ T1] mvneta d0070000.ethernet eth0: Using random mac address aa:89:c9:e0:b8:d0
[ 70.127785][ T1] mvneta d0074000.ethernet eth1: Using random mac address 12:88:5b:60:4f:3f
[ 70.138984][ T1] usbcore: registered new interface driver smsc75xx
[ 70.146996][ T1] orion-ehci d0050000.usb: EHCI Host Controller
[ 70.153582][ T1] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1
[ 70.162193][ T1] orion-ehci d0050000.usb: irq 37, io mem 0xd0050000
[ 70.191470][ T1] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00
[ 70.198400][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 70.207440][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 70.215429][ T1] usb usb1: Product: EHCI Host Controller
[ 70.221054][ T1] usb usb1: Manufacturer: Linux 6.5.7-mvebu-370xp-tld-1 ehci_hcd
[ 70.228686][ T1] usb usb1: SerialNumber: d0050000.usb
[ 70.234928][ T1] hub 1-0:1.0: USB hub found
[ 70.239918][ T1] hub 1-0:1.0: 1 port detected
[ 70.244615][ T674] ata1: SATA link down (SStatus 0 SControl 300)
[ 70.252241][ T1] usbcore: registered new interface driver usblp
[ 70.259860][ T679] ata2: SATA link down (SStatus 0 SControl 300)
[ 70.266284][ T1] usbcore: registered new interface driver usb-storage
[ 70.273072][ T695] ata3: SATA link down (SStatus 0 SControl F300)
[ 70.280286][ T1] mousedev: PS/2 mouse device common for all mice
[ 70.288688][ T1] i2c_dev: i2c /dev entries driver
[ 70.296039][ T1] mv64xxx_i2c d0011000.i2c: can't get pinctrl, bus recovery not supported
[ 70.307772][ T1] rtc-ds1307 0-0068: 'wakeup-source' is set, request for an IRQ is disabled!
[ 70.319554][ T1] rtc-ds1307 0-0068: registered as rtc0
[ 70.326288][ T1] rtc-ds1307 0-0068: setting system clock to 2024-03-02T09:32:16 UTC (1709371936)
[ 70.439436][ T1] orion_wdt: Initial timeout 171 sec
[ 70.446440][ T1] device-mapper: uevent: version 1.0.3
[ 70.452817][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 70.462635][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 70.469888][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 70.477375][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 70.484817][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 70.493109][ T1] sdhci: Secure Digital Host Controller Interface driver
[ 70.500011][ T1] sdhci: Copyright(c) Pierre Ossman
[ 70.506177][ T1] sdhci-pltfm: SDHCI platform and OF driver helper
[ 70.518015][ T1] marvell-cesa d0090000.crypto: CESA device successfully registered
[ 70.526428][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 70.532354][ T100] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 70.541333][ T1] usbcore: registered new interface driver usbhid
[ 70.548437][ T1] usbhid: USB HID core driver
[ 70.554213][ T1] NET: Registered PF_INET6 protocol family
[ 70.561675][ T1] Segment Routing with IPv6
[ 70.566115][ T1] RPL Segment Routing with IPv6
[ 70.570935][ T1] In-situ OAM (IOAM) with IPv6
[ 70.575711][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 70.584234][ T1] NET: Registered PF_PACKET protocol family
[ 70.590904][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 70.595912][ T1] Key type dns_resolver registered
[ 70.601204][ T1] ThumbEE CPU extension supported.
[ 70.606259][ T1] Registering SWP/SWPB emulation handler
[ 70.621953][ T700] ata4: SATA link down (SStatus 0 SControl F300)
[ 70.710458][ T1] registered taskstats version 1
[ 70.716709][ T1] Loading compiled-in X.509 certificates
[ 70.734856][ T1] Key type .fscrypt registered
[ 70.739501][ T1] Key type fscrypt-provisioning registered
[ 70.745335][ T1] Key type big_key registered
[ 70.756203][ T100] usb 1-1: New USB device found, idVendor=05dc, idProduct=c75c, bcdDevice= 1.02
[ 70.771576][ T100] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 70.779449][ T100] usb 1-1: Product: USB Flash Drive
[ 70.798743][ T100] usb 1-1: Manufacturer: Lexar
[ 70.803519][ T1] Key type encrypted registered
[ 70.811632][ T100] usb 1-1: SerialNumber: 20131017233031296A5A
[ 70.820130][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 70.828940][ T100] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 70.837066][ T1] clk: Disabling unused clocks
[ 70.845654][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 70.852862][ T100] scsi host4: usb-storage 1-1:1.0
[ 70.873491][ T1] Checked W+X mappings: passed, no W+X pages found
[ 70.879888][ T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.19-1~deb12u1
[ 71.873635][ T684] scsi 4:0:0:0: Direct-Access Lexar USB Flash Drive 8.07 PQ: 0 ANSI: 4
[ 71.896222][ T35] sd 4:0:0:0: [sda] 15351808 512-byte logical blocks: (7.86 GB/7.32 GiB)
[ 71.912469][ T35] sd 4:0:0:0: [sda] Write Protect is off
[ 71.931505][ T35] sd 4:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 71.958008][ T35] sda: sda1
[ 71.973585][ T35] sd 4:0:0:0: [sda] Attached SCSI removable disk
[ 72.621689][ T1274] usbcore: registered new interface driver uas
[ 72.723531][ T1273] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead.
[ 72.736812][ T1287] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead.
[ 72.753621][ T1278] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead.
[ 72.764169][ T1274] mtdblock: MTD device 'minirootfs' is NAND, please consider using UBI block devices instead.
[ 72.776832][ T1279] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead.
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: recovering journal
rootfs: clean, 26771/480496 files, 290437/1918720 blocks
done.
[ 88.439645][ T1307] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 88.520480][ T1307] EXT4-fs (sda1): mounted filesystem fc59c260-6003-47cc-a825-1bf226996f9b ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 92.109436][ T1488] lm75 0-004c: supply vs not found, using dummy regulator
[ 92.235837][ T1488] hwmon hwmon4: temp1_input not attached to any thermal zone
[ 92.295400][ T1496] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead.
[ 92.312219][ T1489] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead.
[ 92.331780][ T1500] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead.
[ 92.378794][ T1488] lm75 0-004c: hwmon4: sensor 'g751'
[ 92.458070][ T1501] mtdblock: MTD device 'minirootfs' is NAND, please consider using UBI block devices instead.
[ 92.482635][ T1488] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead.
[ 92.607465][ T1497] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 92.689603][ T1487] sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 92.758585][ T1497] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 92.899966][ T1497] xhci_hcd 0000:02:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[ 93.101717][ T1497] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 93.212786][ T1497] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 93.220960][ T1497] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 93.445510][ T1497] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 93.616437][ T1497] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 93.664561][ T1497] usb usb2: Product: xHCI Host Controller
[ 93.670176][ T1497] usb usb2: Manufacturer: Linux 6.5.7-mvebu-370xp-tld-1 xhci-hcd
[ 93.884115][ T1497] usb usb2: SerialNumber: 0000:02:00.0
[ 93.971760][ T1497] hub 2-0:1.0: USB hub found
[ 94.012979][ T1497] hub 2-0:1.0: 2 ports detected
[ 94.054115][ T1497] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 94.135478][ T1497] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.05
[ 94.213646][ T1497] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 94.286989][ T1497] usb usb3: Product: xHCI Host Controller
[ 94.338759][ T1497] usb usb3: Manufacturer: Linux 6.5.7-mvebu-370xp-tld-1 xhci-hcd
[ 94.408557][ T1497] usb usb3: SerialNumber: 0000:02:00.0
[ 94.463791][ T1497] hub 3-0:1.0: USB hub found
[ 94.504750][ T1497] hub 3-0:1.0: 2 ports detected
done.
Activating swap:.
[ 96.023467][ T1649] EXT4-fs (sda1): re-mounted fc59c260-6003-47cc-a825-1bf226996f9b r/w. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
[ 97.591482][ C0] random: crng init done
Initializing random number generator...done.
[ 98.071571][ T2039] mvneta d0070000.ethernet eth0: PHY [d0072004.mdio-mii:00] driver [Marvell 88E1318S] (irq=POLL)
[ 98.089085][ T2039] mvneta d0070000.ethernet eth0: configuring for phy/rgmii-id link mode
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
[ 102.272063][ T905] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15
DHCPOFFER of 10.11.15.78 from 10.11.15.1
DHCPREQUEST for 10.11.15.78 on eth0 to 255.255.255.255 port 67
DHCPACK of 10.11.15.78 from 10.11.15.1
bound to 10.11.15.78 -- renewal in 2757 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2190 (syslogd)
.
Starting periodic command scheduler: cron.
Starting NTP server: ntpd2024-03-02T01:33:03 ntpd[2248]: INIT: ntpd ntpsec-1.2.2: Starting
2024-03-02T01:33:03 ntpd[2248]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:109
.
Starting NTP server: ntpd.
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2219 (klogd)
.
Running local boot scripts (/etc/rc.local)
[ 119.469677][ T2284] Setting Persistent MAC address to 28:C6:8E:35:86:60
<13>Mar 2 01:33:05 root[2291]: Setting Persistent MAC address to 28:C6:8E:35:86:60
Killed old client process
Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on Socket/fallback
DHCPRELEASE of 10.11.15.78 on eth0 to 10.11.15.1 port 67
[ 120.685601][ T100] mvneta d0070000.ethernet eth0: Link is Down
Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
[ 120.817135][ T2323] mvneta d0070000.ethernet eth0: PHY [d0072004.mdio-mii:00] driver [Marvell 88E1318S] (irq=POLL)
[ 120.827826][ T2323] mvneta d0070000.ethernet eth0: configuring for phy/rgmii-id link mode
Listening on LPF/eth0/28:c6:8e:35:86:60
Sending on LPF/eth0/28:c6:8e:35:86:60
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
[ 123.951965][ T100] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19
DHCPOFFER of 10.11.15.78 from 10.11.15.1
DHCPREQUEST for 10.11.15.78 on eth0 to 255.255.255.255 port 67
DHCPACK of 10.11.15.78 from 10.11.15.1
bound to 10.11.15.78 -- renewal in 3194 seconds.
.
Debian GNU/Linux 12 debian ttyS0
debian login: root
Password:
Linux debian 6.5.7-mvebu-370xp-tld-1 #2 PREEMPT Thu Oct 19 18:31:43 PDT 2023 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Fri Mar 1 06:51:02 PST 2024 on ttyS0
debian
10.11.15.78
NETGEAR ReadyNAS 2120
Linux version 6.5.7-mvebu-370xp-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Thu Oct 19 18:31:43 PDT 2023
Debian 12.4
Sat Mar 2 01:33:42 PST 2024 up 2 minutes
root@debian:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00180000 00020000 "u-boot"
mtd1: 00020000 00020000 "u-boot-env"
mtd2: 00600000 00020000 "uImage"
mtd3: 00400000 00020000 "minirootfs"
mtd4: 07400000 00020000 "ubifs"
root@debian:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd1 0x0 0x20000 0x20000
root@debian:~# fw_printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
MPmode=smp
Manufacturer=NETGEAR
Product=ReadyNAS 2120
SKUNum=RN2120
SerialNum=3GB438E8002B2
Startup=Normal
UUID=d612f834-071c-11e3-b44c-28c68e358660
Version=V1.0
amp_enable=no
autoload=no
boot_order=hd_scr hd_img pxe net_img net_scr
bootargs=console=ttyS0,115200 pm_disable=yes mv_cpu_count=2
bootargs_dflt=$console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel
bootargs_end=:10.4.50.254:255.255.255.0:DSMP:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=nand read 0x2000000 0x200000 0x400000; nand read 0x3000000 0x800000 0x400000; bootm 0x2000000 0x3000000 0x1000000
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disL2Cache=yes
disL2Prefetch=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=no
enaCpuStream=no
enaDCPref=yes
enaFPU=yes
enaICPref=yes
enaLPAE=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=28:C6:8E:35:86:61
eth1mtu=1500
eth2addr=00:50:43:00:00:02
eth2mtu=1500
eth3addr=00:50:43:02:00:00
eth3mtu=1500
ethact=egiga1
ethaddr=28:C6:8E:35:86:60
ethmtu=1500
ethprime=egiga1
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-xp-db.dtb
ide_path=/
image_name=uImage
initrd_name=uInitrd
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:02:00:00
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
setL2CacheWT=no
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=host
usbActive=0
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
root@debian:~#
Edited 1 time(s). Last edit at 03/02/2024 03:36AM by spiderdijon.
|
Re: Debian on ReadyNas RN2120 March 02, 2024 04:06AM |
Registered: 2 months ago Posts: 27 |
|
Re: Debian on ReadyNas RN2120 March 02, 2024 02:00PM |
Admin Registered: 13 years ago Posts: 18,575 |
> It still doesn't seem to build kwboot. It builds
> kwbimage.o but that is as far as it goes.
Try building a board
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> kwbimage.o but that is as far as it goes.
Try building a board
make nsa310s_defconfig makeAnd then check the ./tools/ directory.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 March 02, 2024 05:32PM |
Admin Registered: 13 years ago Posts: 18,575 |
spiderdijon,
Use this static kwboot: kwboot_static_2024.04-rc3
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Use this static kwboot: kwboot_static_2024.04-rc3
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on ReadyNas RN2120 March 03, 2024 05:45AM |
Registered: 2 months ago Posts: 27 |
Thanks - The static linked binary works but the result is the same:
I don't think the baud rate option is doing anything as 9600 takes the same amount of time as 115200.
root@poepi:/home/pi# ./kwboot_static -a -b uboot.2024.04-rc3-tld-1.ds414.kwb -t /dev/ttyAMA4 -p kwboot version 2024.04-rc3-00001-g0861eab8ec-dirty Detected kwbimage v1 with SPI boot signature Patching image boot signature to UART Aligning image header to Xmodem block size Sending boot message. Please reboot the target...- Sending boot image header (86272 bytes)... 0 % [......................................................................] 10 % [..................................E xmodem: Protocol error root@poepi:/home/pi# ./kwboot_static -a -b uboot.2024.04-rc3-tld-1.ds414.kwb -t /dev/ttyAMA4 -p kwboot version 2024.04-rc3-00001-g0861eab8ec-dirty Detected kwbimage v1 with SPI boot signature Patching image boot signature to UART Aligning image header to Xmodem block size Sending boot message. Please reboot the target...\ Sending boot image header (86272 bytes)... 0 % [......................................................................] 10 % [...............................................E xmodem: Protocol error root@poepi:/home/pi# ./kwboot_static -a -b uboot.2024.04-rc3-tld-1.ds414.kwb -t /dev/ttyAMA4 -p -B 9600 kwboot version 2024.04-rc3-00001-g0861eab8ec-dirty Detected kwbimage v1 with SPI boot signature Patching image boot signature to UART Injecting binary header code for changing baudrate to 9600 Bd Injecting code for changing baudrate back Aligning image header to Xmodem block size Sending boot message. Please reboot the target...\ Sending boot image header (86656 bytes)... 0 % [......................................................................] 10 % [............................................E
I don't think the baud rate option is doing anything as 9600 takes the same amount of time as 115200.
|
Re: Debian on ReadyNas RN2120 March 03, 2024 02:59PM |
Admin Registered: 13 years ago Posts: 18,575 |
spiderdijon,
Let's be productive and do other tasks first.
Here is the new SMP kernel. Please install and verify that it works for 2 cores.
https://forum.doozan.com/read.php?2,92514,136942#msg-136942
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Let's be productive and do other tasks first.
Here is the new SMP kernel. Please install and verify that it works for 2 cores.
https://forum.doozan.com/read.php?2,92514,136942#msg-136942
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
