SuperPoney
From Stock to Debian on Netgear RN102 in 2024... March 10, 2024 12:11PM |
mkfs -t ext3 -L rootfs /dev/sda mount /dev/sda1 /media/eric/sda cd /media/eric/sda/ tar -xjf /home/eric/Desktop/Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2 cd /media/eric/sda/boot cp -a uImage uImage.orig cp -a zImage-6.6.2-mvebu-tld-1 zImage.fdt cat dts/armada-370-netgear-rn102.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.6.2-mvebu-tld-1 -d zImage.fdt uImage cd sync sync umount /media/eric/sda
setenv mtdparts 'mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)' setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' setenv load_uimage 'ext2load usb 0:1 0x2000000 /boot/uImage' setenv load_uinitrd 'ext2load usb 0:1 0x3000000 /boot/uInitrd' setenv usb_boot 'run load_uimage; if run load_uinitrd; then bootm 0x2000000 0x3000000; else bootm 0x2000000; fi' setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset' setenv fdt_skip_update yes boot
mkfs -t ext3 -L rootfs /dev/sda mount /dev/sda /media/eric/sda cd /media/eric/sda/ tar -xjf /home/eric/Desktop/Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 #kernel mkdir -p /media/eric/rootfs/usr/src/kernel cd /media/eric/rootfs/usr/src/kernel cp /home/eric/Desktop/linux-5.2.9-mvebu-370xp-tld-1-bodhi.tar.bz2 . tar xf linux-5.2.9-mvebu-370xp-tld-1-bodhi.tar.bz2 tar -xvf linux-dtb-5.2.9-mvebu-370xp-tld-1.tar dts/armada-370-netgear-rn102.dtb cp -a zImage-5.2.9-mvebu-370xp-tld-1 zImage.fdt cat dts/armada-370-netgear-rn102.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-mvebu-370xp-tld-1 -d zImage.fdt uImage cd /media/eric/rootfs/boot cp -a /media/eric/rootfs/usr/src/kernel/uImage . sync sync sync cd umount /media/eric/rootfs
setenv mtdparts 'mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)' setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' setenv load_uimage 'ext2load usb 0:1 0x2000000 /boot/uImage' setenv load_uinitrd 'ext2load usb 0:1 0x3000000 /boot/uInitrd' setenv usb_boot 'run load_uimage; if run load_uinitrd; then bootm 0x2000000 0x3000000; else bootm 0x2000000; fi' setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset' setenv fdt_skip_update yes boot
BootROM 1.08 Booting from NAND flash General initialization - Version: 1.0.0 High speed PHY - Version: 2.1.4 (COM-PHY-V20) Update PEX Device ID 0x6710 High speed PHY - Ended Successfully 0000 DDR3 Training Sequence - Ver 5.7.1 DDR3 Training Sequence - Run without PBS. DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED l __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:53:05) Marvell version: v2011.12 2014_T2.0p1 06/23/2015 ReadyNAS-102 V2.0 Board: DB-88F6710-BP SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB Map: Code: 0x1feef000:0x1ff9ef34 BSS: 0x1ffef0a0 Stack: 0x1f9eeef8 Heap: 0x1f9ef000:0x1feef000 NAND: (ID 0xf12c) 128 MiB MMC: MRVL_MMC: 0 Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 Initialize and scan all PCI interfaces PEX unit.port(active IF[-first bus]): ------------------------------------------ PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0 PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0 FPU not initialized USB 0: Host Mode USB 1: Host Mode Shutting down unused interfaces: GBE0 SDIO AUDIO TDM Modules/Interfaces Detected: RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Net: , egiga1 [PRIME] Power On! FDT loaded successfully Hit any key to stop autoboot: Marvell>> printenv AC_Power_fail_detect=open CASset=min HW_version=MVT MALLOC_len=5 Manufacturer=NETGEAR Product=ReadyNAS 102 SKUNum=RN102 SerialNum=3ERD51EJ00892 Startup=Normal UUID=3ab1586c-9e2a-11e4-ae60-e8fcafe56b90 Version=V1.0 autoload=no bootargs=console=ttyS0,115200 bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x200000 0x400000; nand read 0x3000000 0x800000 0x400000; bootm 0x2000000 0x3000000 0x1000000 bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000 bootdelay=0 cacheShare=no console=console=ttyS0,115200 disL2Cache=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=yes enaExtDisk=no enaFPU=no enaMonExt=no enaWrAllo=no envver=3 eth1addr=E8:FC:AF:E5:6B:90 eth1mtu=1500 ethact=egiga1 ethaddr=00:50:43:00:02:02 ethmtu=1500 ethprime=egiga1 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-370-db.dtb image_name=uImage initrd_name=uInitrd load_addr=0x02000000 loadaddr=0x02000000 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500 mv_pon_addr=00:50:43:00:00:02 nandEcc=1bit netbsd_en=no netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 rcvrip=169.254.100.100 sata_delay_reset=0 sata_dma_mode=yes setL2CacheWT=no standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=0 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 2292/131068 bytes Marvell>> setenv mtdparts 'mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)' Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x2000000 /boot/uImage' Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x3000000 /boot/uInitrd' Marvell>> setenv usb_boot 'run load_uimage; if run load_uinitrd; then bootm 0x2000000 0x3000000; else bootm 0x2000000; fi' Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset' Marvell>> setenv fdt_skip_update yes Marvell>> Marvell>> boot (Re)start USB... USB: Active port: 0 Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/boot/uImage" from usb device 0:1 (rootfs) 5418806 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (rootfs) 9488618 bytes read ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-5.19.2-mvebu-370xp-tld-1 Created: 2024-03-10 16:51:15 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5418742 Bytes = 5.2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: initramfs-5.2.9-mvebu-tld-1 Created: 2019-08-26 11:03:27 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9488554 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.8.5-mvebu-370xp-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1.0 SMP PREEMPT Mon Aug 31 00:00:32 PDT 2020 [ 0.000000][ T0] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: NETGEAR ReadyNAS 102 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] HighMem empty [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] CPU: All CPU(s) started in SVC mode. [ 0.000000][ T0] percpu: Embedded 20 pages/cpu s53068 r8192 d20660 u81920 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) earlyprintk=serial mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) reason=normal bdtype=rn102 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 493620K/524288K available (10240K kernel code, 1012K rwdata, 3072K rodata, 1024K init, 342K bss, 30668K reserved, 0K cma-reserved, 0K highmem) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x338/0x794 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x12086300 -> 0x1a086302 [ 0.000000][ T0] Aurora cache controller enabled, 4 ways, 256 kB [ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 [ 0.000000][ T0] Switching to timer-based delay loop, resolution 53ns [ 0.000006][ T0] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114537122277ns [ 0.007874][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101938038664 ns [ 0.019292][ T0] Console: colour dummy device 80x30 [ 0.024010][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 37.49 BogoMIPS (lpj=187492) [ 0.034140][ T0] pid_max: default: 32768 minimum: 301 [ 0.039205][ T0] LSM: Security Framework initializing [ 0.044153][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051482][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.060281][ T0] CPU: Testing write buffer coherency: ok [ 0.065718][ T1] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.072047][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.078739][ T1] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 [ 0.084171][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.090699][ T1] rcu: Hierarchical SRCU implementation. [ 0.098525][ T1] smp: Bringing up secondary CPUs ... [ 0.103413][ T1] smp: Brought up 1 node, 1 CPU [ 0.107709][ T1] SMP: Total of 1 processors activated (37.49 BogoMIPS). [ 0.114027][ T1] CPU: All CPU(s) started in SVC mode. [ 0.119569][ T1] devtmpfs: initialized [ 0.128128][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.137066][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.146834][ T1] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.154042][ T1] xor: measuring software checksum speed [ 0.258573][ T1] arm4regs : 1103.200 MB/sec [ 0.358570][ T1] 8regs : 671.200 MB/sec [ 0.458567][ T1] 32regs : 1062.400 MB/sec [ 0.463020][ T1] xor: using function: arm4regs (1103.200 MB/sec) [ 0.468785][ T1] prandom: seed boundary self test passed [ 0.477388][ T1] prandom: 100 self tests passed [ 0.481802][ T1] pinctrl core: initialized pinctrl subsystem [ 0.488937][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.489676][ T1] NET: Registered protocol family 16 [ 0.502514][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.510407][ T1] audit: initializing netlink subsys (disabled) [ 0.516375][ T31] audit: type=2000 audit(0.490:1): state=initialized audit_enabled=0 res=1 [ 0.526668][ T1] cpuidle: using governor ladder [ 0.532697][ T1] cpuidle: using governor menu [ 0.537187][ T1] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.809631][ T1] raid6: int32x8 gen() 214 MB/s [ 0.978984][ T1] raid6: int32x8 xor() 135 MB/s [ 1.148635][ T1] raid6: int32x4 gen() 224 MB/s [ 1.318707][ T1] raid6: int32x4 xor() 151 MB/s [ 1.488580][ T1] raid6: int32x2 gen() 414 MB/s [ 1.658565][ T1] raid6: int32x2 xor() 217 MB/s [ 1.828602][ T1] raid6: int32x1 gen() 430 MB/s [ 1.998587][ T1] raid6: int32x1 xor() 201 MB/s [ 2.003118][ T1] raid6: using algorithm int32x1 gen() 430 MB/s [ 2.008691][ T1] raid6: .... xor() 201 MB/s, rmw enabled [ 2.013776][ T1] raid6: using intx1 recovery algorithm [ 2.020101][ T1] vgaarb: loaded [ 2.025075][ T1] SCSI subsystem initialized [ 2.030335][ T1] usbcore: registered new interface driver usbfs [ 2.036033][ T1] usbcore: registered new interface driver hub [ 2.043223][ T1] usbcore: registered new device driver usb [ 2.049930][ T1] mc: Linux media interface: v0.10 [ 2.055352][ T1] videodev: Linux video capture interface: v2.00 [ 2.061831][ T1] pps_core: LinuxPPS API ver. 1 registered [ 2.067000][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 2.076737][ T1] PTP clock support registered [ 2.084545][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource [ 3.073755][ T1] VFS: Disk quotas dquot_6.6.0 [ 3.078137][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 3.112966][ T1] NET: Registered protocol family 2 [ 3.120517][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 3.129256][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 3.137304][ T1] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 3.144493][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 3.151586][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 3.158411][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 3.165652][ T1] NET: Registered protocol family 1 [ 3.171030][ T1] RPC: Registered named UNIX socket transport module. [ 3.177170][ T1] RPC: Registered udp transport module. [ 3.182098][ T1] RPC: Registered tcp transport module. [ 3.187046][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.193564][ T1] PCI: CLS 0 bytes, default 64 [ 3.198184][ T1] Trying to unpack rootfs image as initramfs... [ 3.809746][ T1] Freeing initrd memory: 9268K [ 3.814249][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 3.821238][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 3.832246][ T1] Initialise system trusted keyrings [ 3.839058][ T1] Key type blacklist registered [ 3.843589][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 3.850410][ T1] zbud: loaded [ 3.855296][ T1] NFS: Registering the id_resolver key type [ 3.860571][ T1] Key type id_resolver registered [ 3.865276][ T1] Key type id_legacy registered [ 3.869593][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.876508][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.883255][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 3.891554][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 3.898488][ T1] orangefs_init: module version upstream loaded [ 3.976231][ T1] async_tx: api initialized (async) [ 3.980864][ T1] Key type asymmetric registered [ 3.985312][ T1] Asymmetric key parser 'x509' registered [ 3.990748][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 3.998374][ T1] io scheduler bfq registered [ 4.005479][ T1] armada-370-pinctrl d0018000.pin-ctrl: registered pinctrl driver [ 4.022405][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 [ 4.029689][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.035746][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 4.042660][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 4.049343][ T1] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400 [ 4.055584][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 4.062945][ T1] pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400 [ 4.069316][ T1] pci 0000:00:02.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 4.077620][ T1] PCI: bus0: Fast back to back transfers disabled [ 4.083356][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.091555][ T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.099963][ T1] pci 0000:01:00.0: [1b4b:9170] type 00 class 0x010601 [ 4.106374][ T1] pci 0000:01:00.0: reg 0x10: [io 0xfffffff8-0xffffffff] [ 4.112741][ T1] pci 0000:01:00.0: reg 0x14: [io 0xfffffffc-0xffffffff] [ 4.119213][ T1] pci 0000:01:00.0: reg 0x18: [io 0xfffffff8-0xffffffff] [ 4.125670][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xfffffffc-0xffffffff] [ 4.132035][ T1] pci 0000:01:00.0: reg 0x20: [io 0xfffffff0-0xffffffff] [ 4.138455][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x40000000-0x400001ff] [ 4.144882][ T1] pci 0000:01:00.0: reg 0x30: [mem 0xd0000000-0xd000ffff pref] [ 4.151657][ T1] pci 0000:01:00.0: Enabling fixed DMA alias to 00.1 [ 4.157726][ T1] pci 0000:01:00.0: PME# supported from D3hot [ 4.163590][ T1] pci 0000:00:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 4.195641][ T1] PCI: bus1: Fast back to back transfers disabled [ 4.201380][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 4.208478][ T1] pci 0000:02:00.0: [1b73:1009] type 00 class 0x0c0330 [ 4.214824][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x4200ffff 64bit] [ 4.221671][ T1] pci 0000:02:00.0: reg 0x18: [mem 0x42010000-0x42010fff 64bit] [ 4.228621][ T1] pci 0000:02:00.0: reg 0x20: [mem 0x42011000-0x42011fff 64bit] [ 4.235625][ T1] pci 0000:02:00.0: supports D1 [ 4.239924][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold [ 4.246881][ T1] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 4.285637][ T1] PCI: bus2: Fast back to back transfers disabled [ 4.291375][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 4.298198][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff] [ 4.305170][ T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff] [ 4.312084][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 4.318569][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8200000-0xf82007ff pref] [ 4.325821][ T1] pci 0000:00:02.0: BAR 6: assigned [mem 0xf8300000-0xf83007ff pref] [ 4.333057][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xf8000000-0xf800ffff pref] [ 4.340306][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xf8010000-0xf80101ff] [ 4.347162][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 4.353521][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 4.359898][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 4.366275][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 4.372634][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 4.379011][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 4.384180][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 4.390557][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 4.397415][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf810ffff 64bit] [ 4.404749][ T1] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8110000-0xf8110fff 64bit] [ 4.412064][ T1] pci 0000:02:00.0: BAR 4: assigned [mem 0xf8111000-0xf8111fff 64bit] [ 4.419395][ T1] pci 0000:00:02.0: PCI bridge to [bus 02] [ 4.424583][ T1] pci 0000:00:02.0: bridge window [mem 0xf8100000-0xf81fffff] [ 4.431538][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 4.437885][ T1] pcieport 0000:00:02.0: enabling device (0140 -> 0142) [ 4.445396][ T1] mv_xor d0060800.xor: Marvell shared XOR driver [ 4.515916][ T1] mv_xor d0060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.526935][ T1] mv_xor d0060900.xor: Marvell shared XOR driver [ 4.595918][ T1] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.799412][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 4.810525][ T1] printk: console [ttyS0] disabled [ 4.836769][ T1] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 19, base_baud = 12500000) is a 16550A [ 4.845837][ T1] printk: console [ttyS0] enabled [ 4.845837][ T1] printk: console [ttyS0] enabled [ 4.854891][ T1] printk: bootconsole [earlycon0] disabled [ 4.854891][ T1] printk: bootconsole [earlycon0] disabled [ 4.867584][ T1] ahci 0000:01:00.0: enabling device (0146 -> 0147) [ 4.873824][ T1] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode [ 4.882791][ T1] ahci 0000:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 4.894276][ T1] scsi host0: ahci [ 4.898944][ T1] scsi host1: ahci [ 4.902992][ T1] ata1: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010100 irq 42 [ 4.910795][ T1] ata2: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010180 irq 42 [ 4.919773][ T1] sata_mv d00a0000.sata: slots 32 ports 1 [ 4.927790][ T1] scsi host2: sata_mv [ 4.932100][ T1] ata3: SATA max UDMA/133 irq 27 [ 4.938204][ T1] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1 [ 4.945765][ T1] nand: Micron MT29F1G08ABADAWP [ 4.950110][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 4.958628][ T1] Bad block table found at page 65472, version 0x01 [ 4.965272][ T1] Bad block table found at page 65408, version 0x01 [ 4.971535][ T1] 5 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 4.978286][ T1] Creating 5 MTD partitions on "pxa3xx_nand-0": [ 4.983907][ T1] 0x000000000000-0x000000180000 : "u-boot" [ 4.991421][ T1] 0x000000180000-0x0000001a0000 : "u-boot-env" [ 4.999774][ T1] 0x000000200000-0x000000800000 : "uImage" [ 5.007849][ T1] 0x000000800000-0x000000c00000 : "minirootfs" [ 5.016272][ T1] 0x000000c00000-0x000008000000 : "ubifs" [ 5.026235][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 5.034098][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 5.048515][ T1] libphy: Fixed MDIO Bus: probed [ 5.058159][ T1] libphy: orion_mdio_bus: probed [ 5.080064][ T1] mvneta d0074000.ethernet eth0: Using random mac address d6:80:a4:bc:c6:ee [ 5.092541][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.099822][ T1] ehci-pci: EHCI PCI platform driver [ 5.105171][ T1] ehci-orion: EHCI orion driver [ 5.109723][ T1] orion-ehci d0050000.usb: EHCI Host Controller [ 5.115741][ T1] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1 [ 5.123660][ T1] orion-ehci d0050000.usb: irq 25, io mem 0xd0050000 [ 5.154605][ T1] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00 [ 5.161093][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 5.169460][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.176828][ T1] usb usb1: Product: EHCI Host Controller [ 5.182017][ T1] usb usb1: Manufacturer: Linux 5.8.5-mvebu-370xp-tld-1 ehci_hcd [ 5.189057][ T1] usb usb1: SerialNumber: d0050000.usb [ 5.195098][ T1] hub 1-0:1.0: USB hub found [ 5.199591][ T1] hub 1-0:1.0: 1 port detected [ 5.205447][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 5.211479][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2 [ 5.219912][ T1] xhci_hcd 0000:02:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010 [ 5.230035][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 5.238425][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.245798][ T1198] ata2: SATA link down (SStatus 0 SControl 300) [ 5.251486][ T1194] ata1: SATA link down (SStatus 0 SControl 300) [ 5.257163][ T1] usb usb2: Product: xHCI Host Controller [ 5.262403][ T1] usb usb2: Manufacturer: Linux 5.8.5-mvebu-370xp-tld-1 xhci-hcd [ 5.269429][ T1209] ata3: SATA link down (SStatus 0 SControl F300) [ 5.275204][ T1] usb usb2: SerialNumber: 0000:02:00.0 [ 5.281146][ T1] hub 2-0:1.0: USB hub found [ 5.285656][ T1] hub 2-0:1.0: 2 ports detected [ 5.291100][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 5.297009][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3 [ 5.304484][ T1] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed [ 5.311232][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.319649][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08 [ 5.327978][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.335327][ T1] usb usb3: Product: xHCI Host Controller [ 5.340464][ T1] usb usb3: Manufacturer: Linux 5.8.5-mvebu-370xp-tld-1 xhci-hcd [ 5.347483][ T1] usb usb3: SerialNumber: 0000:02:00.0 [ 5.353322][ T1] hub 3-0:1.0: USB hub found [ 5.357806][ T1] hub 3-0:1.0: 2 ports detected [ 5.363890][ T1] usbcore: registered new interface driver usblp [ 5.370581][ T1] usbcore: registered new interface driver usb-storage [ 5.377809][ T1] mousedev: PS/2 mouse device common for all mice [ 5.385730][ T1] i2c /dev entries driver [ 5.394142][ T1] rtc-ds1307 0-0068: 'wakeup-source' is set, request for an IRQ is disabled! [ 5.407654][ T1] rtc-ds1307 0-0068: registered as rtc0 [ 5.413671][ T1] rtc-ds1307 0-0068: setting system clock to 2024-03-10T16:53:39 UTC (1710089619) [ 5.456313][ T1] orion_wdt: Initial timeout 229 sec [ 5.462741][ T1] device-mapper: uevent: version 1.0.3 [ 5.468695][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com [ 5.477977][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 5.484839][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 5.491576][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 5.498615][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 5.504948][ T1] device-mapper: raid: Loading target version 1.15.1 [ 5.518475][ T1] marvell-cesa d0090000.crypto: CESA device successfully registered [ 5.526558][ T1] hid: raw HID events driver (C) Jiri Kosina [ 5.533209][ T1] usbcore: registered new interface driver usbhid [ 5.539504][ T1] usbhid: USB HID core driver [ 5.544404][ T1] drop_monitor: Initializing network drop monitor service [ 5.552153][ T1] NET: Registered protocol family 10 [ 5.558420][ T1] Segment Routing with IPv6 [ 5.562447][ T1] RPL Segment Routing with IPv6 [ 5.566935][ T20] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 5.574121][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 5.582650][ T1] NET: Registered protocol family 17 [ 5.588443][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 5.593025][ T1] Key type dns_resolver registered [ 5.597990][ T1] ThumbEE CPU extension supported. [ 5.602575][ T1] Registering SWP/SWPB emulation handler [ 5.608203][ T1] registered taskstats version 1 [ 5.612642][ T1] Loading compiled-in X.509 certificates [ 5.618195][ T1] zswap: loaded using pool lzo/zbud [ 5.623327][ T1] Key type ._fscrypt registered [ 5.627834][ T1] Key type .fscrypt registered [ 5.632090][ T1] Key type fscrypt-provisioning registered [ 5.640346][ T1] Key type big_key registered [ 5.668579][ T1] Key type encrypted registered [ 5.677660][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 5.688835][ T1] Freeing unused kernel memory: 1024K [ 5.716680][ T1] Checked W+X mappings: passed, no W+X pages found [ 5.722565][ T1] Run /init as init process [ 5.766632][ T20] usb 1-1: New USB device found, idVendor=152d, idProduct=0576, bcdDevice=41.01 [ 5.779421][ T20] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Loading, please wait... [ 5.792635][ T20] usb 1-1: Product: ANKEJE USB3.0 [ 5.802503][ T20] usb 1-1: Manufacturer: ANKEJE USB3.0 [ 5.813034][ T20] usb 1-1: SerialNumber: DD56419883014 Starting version 241 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. done. Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! LABEL=rootfs does not exist. Dropping to a shell! BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs)
Re: From Stock to Debian on Netgear RN102 in 2024... March 10, 2024 02:16PM |
Admin Registered: 13 years ago Posts: 19,106 |
> mkfs -t ext3 -L rootfs /dev/sda > mount /dev/sda1 /media/eric/sda > cd /media/eric/sda/ > tar -xjf > /home/eric/Desktop/Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2 > cd /media/eric/sda/boot > cp -a uImage uImage.orig > cp -a zImage-6.6.2-mvebu-tld-1 zImage.fdt > cat dts/armada-370-netgear-rn102.dtb >> > zImage.fdt > mkimage -A arm -O linux -T kernel -C none -a > 0x00008000 -e 0x00008000 -n > Linux-6.6.2-mvebu-tld-1 -d zImage.fdt uImage > cd > sync > sync > umount /media/eric/sda >
SuperPoney
Re: From Stock to Debian on Netgear RN102 in 2024... March 13, 2024 05:37AM |
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x2000000 /boot/uImage' Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x3000000 /boot/uInitrd'
Marvell>> setenv load_uimage 'ext2load usb 0:0 0x2000000 /boot/uImage' Marvell>> setenv load_uinitrd 'ext2load usb 0:0 0x3000000 /boot/uInitrd'
BootROM 1.08 Booting from NAND flash General initialization - Version: 1.0.0 High speed PHY - Version: 2.1.4 (COM-PHY-V20) Update PEX Device ID 0x6710 High speed PHY - Ended Successfully 0000 DDR3 Training Sequence - Ver 5.7.1 DDR3 Training Sequence - Run without PBS. DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED l __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:53:05) Marvell version: v2011.12 2014_T2.0p1 06/23/2015 ReadyNAS-102 V2.0 Board: DB-88F6710-BP SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB l Map: Code: 0x1feef000:0x1ff9ef34 BSS: 0x1ffef0a0 Stack: 0x1f9eeef8 Heap: 0x1f9ef000:0x1feef000 NAND: (ID 0xf12c) 128 MiB MMC: MRVL_MMC: 0 Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 Initialize and scan all PCI interfaces PEX unit.port(active IF[-first bus]): ------------------------------------------ PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0 PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0 FPU not initialized USB 0: Host Mode USB 1: Host Mode Shutting down unused interfaces: GBE0 SDIO AUDIO TDM Modules/Interfaces Detected: RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Net: , egiga1 [PRIME] Power On! FDT loaded successfully Hit any key to stop autoboot: 0 0 Marvell>> bb Marvell>> Marvell>> Marvell>> Marvell>> Marvell>> setenv mtdparts 'mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)' Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' Marvell>> setenv load_uimage 'ext2load usb 0:0 0x2000000 /boot/uImage' Marvell>> setenv load_uinitrd 'ext2load usb 0:0 0x3000000 /boot/uInitrd' Marvell>> setenv usb_boot 'run load_uimage; if run load_uinitrd; then bootm 0x2000000 0x3000000; else bootm 0x2000000; fi' Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset' Marvell>> setenv fdt_skip_update yes Marvell>> Marvell>> Marvell>> boot (Re)start USB... USB: Active port: 0 Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/boot/uImage" from usb device 0 5073558 bytes read Loading file "/boot/uInitrd" from usb device 0 5257173 bytes read ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-5.8.5-mvebu-370xp-tld-1 Created: 2024-03-13 8:20:41 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5073494 Bytes = 4.8 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: initramfs-6.6.2-mvebu-tld-1 Created: 2023-12-12 22:03:52 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5257109 Bytes = 5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.19.2-mvebu-370xp-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 PREEMPT Sun Aug 21 14:07:19 PDT 2022 [ 0.000000][ T0] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: NETGEAR ReadyNAS 102 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] HighMem empty [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] CPU: All CPU(s) started in SVC mode. [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) earlyprintk=serial mtdparts=pxa3xx_nand-0:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs) reason=normal bdtype=rn102 [ 0.000000][ T0] Unknown kernel command line parameters "reason=normal bdtype=rn102", will be passed to user space. [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 495148K/524288K available (10240K kernel code, 1494K rwdata, 3404K rodata, 1024K init, 468K bss, 29140K reserved, 0K cma-reserved, 0K highmem) [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x12086300 -> 0x1a086302 [ 0.000000][ T0] Aurora cache controller enabled, 4 ways, 256 kB [ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval) [ 0.000000][ T0] Switching to timer-based delay loop, resolution 53ns [ 0.000001][ T0] sched_clock: 32 bits at 19MHz, resolution 53ns, wraps every 114537122277ns [ 0.007873][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 101938038664 ns [ 0.019427][ T0] Console: colour dummy device 80x30 [ 0.024155][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 37.49 BogoMIPS (lpj=187492) [ 0.034277][ T0] pid_max: default: 32768 minimum: 301 [ 0.039464][ T0] LSM: Security Framework initializing [ 0.044505][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051840][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.060634][ T0] CPU: Testing write buffer coherency: ok [ 0.067271][ T1] cblist_init_generic: Setting adjustable number of callback queues. [ 0.074560][ T1] cblist_init_generic: Setting shift to 0 and lim to 1. [ 0.080912][ T1] cblist_init_generic: Setting shift to 0 and lim to 1. [ 0.087290][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.093955][ T1] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 [ 0.099419][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.105912][ T1] rcu: Hierarchical SRCU implementation. [ 0.110951][ T1] rcu: Max phase no-delay instances is 1000. [ 0.117655][ T1] devtmpfs: initialized [ 0.126270][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.134371][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.144014][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.151011][ T1] prandom: seed boundary self test passed [ 0.158623][ T1] prandom: 100 self tests passed [ 0.163001][ T1] pinctrl core: initialized pinctrl subsystem [ 0.170164][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.177316][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.185028][ T1] audit: initializing netlink subsys (disabled) [ 0.191653][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.191925][ T17] audit: type=2000 audit(0.170:1): state=initialized audit_enabled=0 res=1 [ 0.205833][ T1] cpuidle: using governor ladder [ 0.210255][ T1] cpuidle: using governor menu [ 0.214690][ T1] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.220772][ T1] mvebu-pmsu: CPU idle is currently broken: disabling [ 0.608552][ T1] raid6: int32x8 gen() 212 MB/s [ 0.948548][ T1] raid6: int32x4 gen() 232 MB/s [ 1.288564][ T1] raid6: int32x2 gen() 360 MB/s [ 1.628547][ T1] raid6: int32x1 gen() 408 MB/s [ 1.633090][ T1] raid6: using algorithm int32x1 gen() 408 MB/s [ 1.988547][ T1] raid6: .... xor() 171 MB/s, rmw enabled [ 1.993644][ T1] raid6: using intx1 recovery algorithm [ 2.009776][ T1] SCSI subsystem initialized [ 2.014481][ T1] usbcore: registered new interface driver usbfs [ 2.028651][ T1] usbcore: registered new interface driver hub [ 2.034209][ T1] usbcore: registered new device driver usb [ 2.048990][ T1] pps_core: LinuxPPS API ver. 1 registered [ 2.054162][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 2.078577][ T1] PTP clock support registered [ 2.089999][ T1] vgaarb: loaded [ 2.099143][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource [ 2.119523][ T1] VFS: Disk quotas dquot_6.6.0 [ 2.123828][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.160607][ T1] NET: Registered PF_INET protocol family [ 2.165998][ T1] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 2.189626][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 2.198327][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 2.219209][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 2.226966][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 2.249197][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 2.256006][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 2.279297][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 2.285915][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 2.309371][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 2.315956][ T1] RPC: Registered named UNIX socket transport module. [ 2.329190][ T1] RPC: Registered udp transport module. [ 2.334127][ T1] RPC: Registered tcp transport module. [ 2.339055][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.359164][ T1] PCI: CLS 0 bytes, default 64 [ 2.363774][ T31] Trying to unpack rootfs image as initramfs... [ 2.389479][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 2.396379][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.519730][ T1] Initialise system trusted keyrings [ 2.524504][ T1] Key type blacklist registered [ 2.540094][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 2.546742][ T1] zbud: loaded [ 2.569662][ T1] NFS: Registering the id_resolver key type [ 2.574972][ T1] Key type id_resolver registered [ 2.589248][ T1] Key type id_legacy registered [ 2.593670][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.609237][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.616651][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.779637][ T1] xor: measuring software checksum speed [ 2.799294][ T1] arm4regs : 1148 MB/sec [ 2.819247][ T1] 8regs : 964 MB/sec [ 2.849393][ T1] 32regs : 1113 MB/sec [ 2.854039][ T1] xor: using function: arm4regs (1148 MB/sec) [ 2.869397][ T1] async_tx: api initialized (async) [ 2.874045][ T1] Key type asymmetric registered [ 2.878421][ T1] Asymmetric key parser 'x509' registered [ 2.912455][ T31] Freeing initrd memory: 5136K [ 2.948893][ T1] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 2.955640][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 2.963611][ T1] io scheduler bfq registered [ 2.970928][ T1] armada-370-pinctrl d0018000.pin-ctrl: registered pinctrl driver [ 2.984933][ T1] debugfs: Directory 'd0018100.gpio' with parent 'regmap' already present! [ 2.995083][ T1] debugfs: Directory 'd0018140.gpio' with parent 'regmap' already present! [ 3.006805][ T1] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: [ 3.016551][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0040000..0x00d0041fff -> 0x0000040000 [ 3.025188][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0080000..0x00d0081fff -> 0x0000080000 [ 3.033847][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 3.042812][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 3.051753][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 3.060700][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 3.069772][ T1] mvebu-pcie soc:pcie@82000000: pcie0.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@1,0 does not contain intx interrupt [ 3.083899][ T1] mvebu-pcie soc:pcie@82000000: pcie1.0: legacy INTx interrupts cannot be masked individually, /soc/pcie@82000000/pcie@2,0 does not contain intx interrupt [ 3.098464][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 [ 3.105554][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.111313][ T1] pci_bus 0000:00: root bus resource [mem 0xd0040000-0xd0041fff] (bus address [0x00040000-0x00041fff]) [ 3.121287][ T1] pci_bus 0000:00: root bus resource [mem 0xd0080000-0xd0081fff] (bus address [0x00080000-0x00081fff]) [ 3.131254][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 3.138171][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 3.144735][ T1] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400 [ 3.151536][ T1] pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400 [ 3.159718][ T1] PCI: bus0: Fast back to back transfers disabled [ 3.165466][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.173500][ T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.181971][ T1] pci 0000:01:00.0: [1b4b:9170] type 00 class 0x010601 [ 3.188116][ T1] pci 0000:01:00.0: reg 0x10: [io 0xfffffff8-0xffffffff] [ 3.194827][ T1] pci 0000:01:00.0: reg 0x14: [io 0xfffffffc-0xffffffff] [ 3.201304][ T1] pci 0000:01:00.0: reg 0x18: [io 0xfffffff8-0xffffffff] [ 3.207675][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xfffffffc-0xffffffff] [ 3.214087][ T1] pci 0000:01:00.0: reg 0x20: [io 0xfffffff0-0xffffffff] [ 3.220493][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x40000000-0x400001ff] [ 3.226863][ T1] pci 0000:01:00.0: reg 0x30: [mem 0xd0000000-0xd000ffff pref] [ 3.233669][ T1] pci 0000:01:00.0: Enabling fixed DMA alias to 00.1 [ 3.239722][ T1] pci 0000:01:00.0: PME# supported from D3hot [ 3.245628][ T1] pci 0000:00:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 3.280310][ T1] PCI: bus1: Fast back to back transfers disabled [ 3.286052][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.293185][ T1] pci 0000:02:00.0: [1b73:1009] type 00 class 0x0c0330 [ 3.299660][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x4200ffff 64bit] [ 3.306517][ T1] pci 0000:02:00.0: reg 0x18: [mem 0x42010000-0x42010fff 64bit] [ 3.313458][ T1] pci 0000:02:00.0: reg 0x20: [mem 0x42011000-0x42011fff 64bit] [ 3.320432][ T1] pci 0000:02:00.0: supports D1 [ 3.324734][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold [ 3.331728][ T1] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 3.370210][ T1] PCI: bus2: Fast back to back transfers disabled [ 3.375952][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.382733][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff] [ 3.389714][ T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff] [ 3.396634][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 3.403190][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xf8000000-0xf800ffff pref] [ 3.410448][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xf8010000-0xf80101ff] [ 3.417290][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 3.423667][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 3.430043][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 3.436407][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 3.442782][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 3.449285][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 3.454460][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 3.460845][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 3.467696][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf810ffff 64bit] [ 3.475031][ T1] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8110000-0xf8110fff 64bit] [ 3.482363][ T1] pci 0000:02:00.0: BAR 4: assigned [mem 0xf8111000-0xf8111fff 64bit] [ 3.489695][ T1] pci 0000:00:02.0: PCI bridge to [bus 02] [ 3.494869][ T1] pci 0000:00:02.0: bridge window [mem 0xf8100000-0xf81fffff] [ 3.501954][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 3.508312][ T1] pcieport 0000:00:02.0: enabling device (0140 -> 0142) [ 3.515805][ T1] mv_xor d0060800.xor: Marvell shared XOR driver [ 3.580433][ T1] mv_xor d0060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 3.591575][ T1] mv_xor d0060900.xor: Marvell shared XOR driver [ 3.660600][ T1] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 3.927859][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.942448][ T1] printk: console [ttyS0] disabled [ 3.970477][ T1] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 29, base_baud = 12500000) is a 16550A [ 3.979608][ T1] printk: console [ttyS0] enabled [ 3.979608][ T1] printk: console [ttyS0] enabled [ 3.988604][ T1] printk: bootconsole [earlycon0] disabled [ 3.988604][ T1] printk: bootconsole [earlycon0] disabled [ 4.002275][ T1] ahci 0000:01:00.0: enabling device (0146 -> 0147) [ 4.008530][ T1] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode [ 4.018849][ T1] ahci 0000:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 4.031517][ T1] scsi host0: ahci [ 4.036573][ T1] scsi host1: ahci [ 4.041014][ T1] ata1: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010100 irq 31 [ 4.048410][ T1] ata2: SATA max UDMA/133 abar m512@0xf8010000 port 0xf8010180 irq 31 [ 4.057966][ T1] sata_mv d00a0000.sata: slots 32 ports 1 [ 4.067224][ T1] scsi host2: sata_mv [ 4.071799][ T1] ata3: SATA max UDMA/133 irq 32 [ 4.078586][ T1] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1 [ 4.086570][ T1] nand: Micron MT29F1G08ABADAWP [ 4.091087][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 4.099459][ T1] Bad block table found at page 65472, version 0x01 [ 4.105939][ T1] Bad block table found at page 65408, version 0x01 [ 4.112249][ T1] 5 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 4.118911][ T1] Creating 5 MTD partitions on "pxa3xx_nand-0": [ 4.124572][ T1] 0x000000000000-0x000000180000 : "u-boot" [ 4.132120][ T1] 0x000000180000-0x0000001a0000 : "u-boot-env" [ 4.141135][ T1] 0x000000200000-0x000000800000 : "uImage" [ 4.149827][ T1] 0x000000800000-0x000000c00000 : "minirootfs" [ 4.158768][ T1] 0x000000c00000-0x000008000000 : "ubifs" [ 4.169603][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 4.177483][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 4.225527][ T1] mvneta d0074000.ethernet eth0: Using random mac address 5a:bb:0f:0f:d6:3c [ 4.238680][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.246438][ T1] ehci-pci: EHCI PCI platform driver [ 4.251742][ T1] ehci-orion: EHCI orion driver [ 4.256390][ T1] orion-ehci d0050000.usb: EHCI Host Controller [ 4.262489][ T1] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1 [ 4.270588][ T1] orion-ehci d0050000.usb: irq 35, io mem 0xd0050000 [ 4.299196][ T1] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00 [ 4.305640][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.19 [ 4.313989][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.321351][ T1] usb usb1: Product: EHCI Host Controller [ 4.326527][ T1] usb usb1: Manufacturer: Linux 5.19.2-mvebu-370xp-tld-1 ehci_hcd [ 4.333641][ T1] usb usb1: SerialNumber: d0050000.usb [ 4.339684][ T1] hub 1-0:1.0: USB hub found [ 4.344464][ T1] hub 1-0:1.0: 1 port detected [ 4.350608][ T1] usbcore: registered new interface driver usblp [ 4.357968][ T1] usbcore: registered new interface driver usb-storage [ 4.365412][ T1] mousedev: PS/2 mouse device common for all mice [ 4.373900][ T1] i2c_dev: i2c /dev entries driver [ 4.383653][ T664] ata2: SATA link down (SStatus 0 SControl 300) [ 4.390180][ T659] ata1: SATA link down (SStatus 0 SControl 300) [ 4.396049][ T1] rtc-ds1307 0-0068: 'wakeup-source' is set, request for an IRQ is disabled! [ 4.404075][ T676] ata3: SATA link down (SStatus 0 SControl F300) [ 4.414633][ T1] rtc-ds1307 0-0068: registered as rtc0 [ 4.422478][ T1] rtc-ds1307 0-0068: setting system clock to 2024-03-13T10:23:22 UTC (1710325402) [ 4.461074][ T1] orion_wdt: Initial timeout 229 sec [ 4.468462][ T1] device-mapper: uevent: version 1.0.3 [ 4.474296][ T1] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 4.483696][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 4.490676][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 4.497422][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 4.504294][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 4.510610][ T1] device-mapper: raid: Loading target version 1.15.1 [ 4.524063][ T1] marvell-cesa d0090000.crypto: CESA device successfully registered [ 4.532260][ T1] hid: raw HID events driver (C) Jiri Kosina [ 4.539580][ T1] usbcore: registered new interface driver usbhid [ 4.545375][ T1] usbhid: USB HID core driver [ 4.551432][ T1] drop_monitor: Initializing network drop monitor service [ 4.558389][ T1] NET: Registered PF_INET6 protocol family [ 4.566103][ T1] Segment Routing with IPv6 [ 4.570382][ T1] RPL Segment Routing with IPv6 [ 4.574814][ T1] In-situ OAM (IOAM) with IPv6 [ 4.579329][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.587617][ T1] NET: Registered PF_PACKET protocol family [ 4.594223][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 4.598804][ T1] Key type dns_resolver registered [ 4.603808][ T1] ThumbEE CPU extension supported. [ 4.608399][ T1] Registering SWP/SWPB emulation handler [ 4.614137][ T1] registered taskstats version 1 [ 4.618582][ T1] Loading compiled-in X.509 certificates [ 4.624886][ T1] zswap: loaded using pool lzo/zbud [ 4.629636][ T60] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 4.637204][ T1] Key type ._fscrypt registered [ 4.641646][ T1] Key type .fscrypt registered [ 4.645938][ T1] Key type fscrypt-provisioning registered [ 4.654733][ T1] Key type big_key registered [ 4.687812][ T1] Key type encrypted registered [ 4.703468][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.715908][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 4.741287][ T1] Checked W+X mappings: passed, no W+X pages found [ 4.747187][ T1] Run /init as init process Loading, please wait... [ 4.830751][ T60] usb 1-1: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00 [ 4.838980][ T60] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.850741][ T60] usb 1-1: Product: Cruzer Fit [ 4.855029][ T60] usb 1-1: Manufacturer: SanDisk [ 4.872391][ T60] usb 1-1: SerialNumber: 4C530001151025117080 [ 4.886419][ T60] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.900082][ T60] scsi host3: usb-storage 1-1:1.0 Starting systemd-udevd version 252.19-1~deb12u1 [ 5.940681][ T35] scsi 3:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6 [ 5.964735][ T27] sd 3:0:0:0: [sda] 61341696 512-byte logical blocks: (31.4 GB/29.3 GiB) [ 5.981018][ T27] sd 3:0:0:0: [sda] Write Protect is off [ 5.999319][ T27] sd 3:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 6.028760][ T27] sd 3:0:0:0: [sda] Attached SCSI removable disk [ 6.715932][ T977] mvneta d0074000.ethernet end1: renamed from eth0 [ 6.742548][ T976] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 6.758319][ T975] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead. [ 6.769087][ T983] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead. [ 6.790278][ T974] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead. [ 6.819764][ T985] mtdblock: MTD device 'minirootfs' is NAND, please consider using UBI block devices instead. Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.38.1 [/sbin/fsck.ext3 (1) -- /dev/sda] fsck.ext3 -a -C0 /dev/sda rootfs: clean, 25887/1916928 files, 380270/7667712 blocks done. [ 18.420097][ T1003] EXT4-fs (sda): mounting ext3 file system using the ext4 subsystem [ 18.542698][ T1003] EXT4-fs (sda): mounted filesystem with ordered data mode. Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 3.06 booting INIT: No inittab.d directory found Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 22.400471][ T1136] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead. [ 22.417825][ T1140] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 22.468877][ T1138] mtdblock: MTD device 'uImage' is NAND, please consider using UBI block devices instead. [ 22.522864][ T1141] mtdblock: MTD device 'minirootfs' is NAND, please consider using UBI block devices instead. [ 22.581610][ T1140] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead. done. Activating swap:. [ 25.649446][ T1282] EXT4-fs (sda): re-mounted. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. [ 27.136827][ T961] random: crng init done Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. Initializing random number generator...done. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1 Copyright 2004-2022 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Cannot find device "eth0" Failed to get interface index: No such device If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging. exiting. ifup: failed to bring up eth0 [31mfailed.[0m Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Not starting NFS kernel daemon: no exports ... [33m(warning).[0m Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1771 (syslogd) . Starting periodic command scheduler: cron. Starting system message bus: dbus. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting NTP server: ntpd2024-03-13T03:23:51 ntpd[1826]: INIT: ntpd ntpsec-1.2.2: Starting 2024-03-13T03:23:51 ntpd[1826]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:109 . Starting NTP server: ntpd. Starting OpenBSD Secure Shell server: sshdsshd: no hostkeys available -- exiting. [31mfailed![0m Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1797 (klogd) . Running local boot scripts (/etc/rc.local)
scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/boot/uImage" from usb device 0 5195211 bytes read Loading file "/boot/uInitrd" from usb device 0 5257173 bytes read ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-6.6.2-mvebu-tld-1 Created: 2024-03-13 8:25:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5195147 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: initramfs-6.6.2-mvebu-tld-1 Created: 2023-12-12 22:03:52 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5257109 Bytes = 5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ...
SuperPoney
Re: From Stock to Debian on Netgear RN102 in 2024... March 13, 2024 12:08PM |
ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: end1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1024 link/ether 7e:ae:eb:77:74:3f brd ff:ff:ff:ff:ff:ff 3: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000 link/sit 0.0.0.0 brd 0.0.0.0 4: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN group default qlen 1000 link/tunnel6 :: brd :: permaddr 4a9f:f73:a239::
rename /end0=eth0 auto lo eth0 iface lo inet loopback iface eth0 inet dhcp
rename /end1=eth0 auto lo eth0 iface lo inet loopback iface eth0 inet dhcp
Re: From Stock to Debian on Netgear RN102 in 2024... March 13, 2024 02:46PM |
Admin Registered: 13 years ago Posts: 19,106 |
Net: , egiga1 [PRIME] Power On! FDT loaded successfully Hit any key to stop autoboot: Marvell>> printenv eth1addr=E8:FC:AF:E5:6B:90 eth1mtu=1500 ethact=egiga1 ethaddr=00:50:43:00:02:02 ethmtu=1500 ethprime=egiga1
rename /end1=eth0
ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: end1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1024 link/ether 7e:ae:eb:77:74:3f brd ff:ff:ff:ff:ff:ff 3: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000 link/sit 0.0.0.0 brd 0.0.0.0 4: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN group default qlen 1000 link/tunnel6 :: brd :: permaddr 4a9f:f73:a239::
SuperPoney
Re: From Stock to Debian on Netgear RN102 in 2024... March 13, 2024 03:18PM |
Re: From Stock to Debian on Netgear RN102 in 2024... March 13, 2024 03:35PM |
Admin Registered: 13 years ago Posts: 19,106 |
Quote
Updated 16 Dec 2023:
Rootfs Debian-6.6.2-mvebu-tld-1-rootfs-bodhi.tar.bz2 has been uploaded.
Basic Debian bookworm armhf rootfs for most MVEBU Armada NAS:
....
Note 6. Persistent MAC address (Optional):
To enable the network dynamic IP to stay consistent after each reboot, and also for faster boot. In this rootfs, a script is executed during kernel booting (in /etc/rc.local), to detect if a local MAC address was assigned during boot, and then set the persistent MAC address to what is currently defined in u-boot env ethaddr.
/root/set_persistent_mac_address
To keep using the kernel generated local MAC address (if local MAC address was generated in your box) then chmod this script to non-executable.
chmod -x /root/set_persistent_mac_address