Debian on Synology DS112
Posted by BayPanard
|
Re: Debian on Synology DS112 March 10, 2025 12:53PM |
Registered: 5 weeks ago Posts: 18 |
Bodhi,
Here is the full boot log from u-boot to debian login with "printenv" included :
Thanks!
/BayPanard
Here is the full boot log from u-boot to debian login with "printenv" included :
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Aug 1 2011 - 17:06:51) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4
Soc: 88F6282 A0CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
[4096kB@f8000000] Flash: 4 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: PCI Express Root Complex Interface
PEX interface detected Link X1
Synology Model: DS112
Fan Status: Good
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Marvell>> setenv ipaddr 192.168.1.128
Marvell>> setenv serverip 192.168.1.180
Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> mw 0x800000 0 1
Marvell>> tftpboot 0x800000 uImage
Using egiga0 device
TFTP from server 192.168.1.180; our IP address is 192.168.1.128
Filename 'uImage'.
Load address: 0x800000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##################################################
done
Bytes transferred = 6246316 (5f4fac hex)
Marvell>> tftpboot 0x2100000 uInitrd
Using egiga0 device
TFTP from server 192.168.1.180; our IP address is 192.168.1.128
Filename 'uInitrd'.
Load address: 0x2100000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########################
done
Bytes transferred = 5791271 (585e27 hex)
Marvell>> printenv
bootcmd=bootm F8080000 F8280000
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
run_diag=yes
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=spi_flash:0x80000@0(uboot)ro,0x300000@0x100000(root)
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
bootdelay=3
disaMvPnp=no
ethaddr=00:50:43:3c:3b:5d
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
pcieTune=no
pcieTune1=no
ethact=egiga0
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
filesize=585e27
fileaddr=2100000
netmask=255.255.254.0
ipaddr=192.168.1.128
serverip=192.168.1.180
Environment size: 1151/4092 bytes
Marvell>> bootm 0x800000 0x2100000
## Booting image at 00800000 ...
Image Name: /mnt/c/Users/alexis/Downloads/DS
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6246252 Bytes = 6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
Image Name: initramfs-6.5.7-kirkwood-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5791207 Bytes = 5.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Synology DS112 V10j
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 232300K/262144K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 29844K reserved, 0K cma-reserved)
[ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000001][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.008518][ T0] Switching to timer-based delay loop, resolution 5ns
[ 0.015586][ T0] Console: colour dummy device 80x30
[ 0.020796][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.032011][ T0] CPU: Testing write buffer coherency: ok
[ 0.037665][ T0] pid_max: default: 32768 minimum: 301
[ 0.049588][ T0] LSM: initializing lsm=capability,integrity
[ 0.057211][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.065243][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.083097][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.091144][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.099791][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.106914][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x0
[ 0.113108][ T1] rcu: Hierarchical SRCU implementation.
[ 0.118651][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.126745][ T1] devtmpfs: initialized
[ 0.143886][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.154466][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.164107][ T1] prandom: seed boundary self test passed
[ 0.172891][ T1] prandom: 100 self tests passed
[ 0.177670][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.186499][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.194314][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.206027][ T1] audit: initializing netlink subsys (disabled)
[ 0.213730][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.213855][ T1] cpuidle: using governor ladder
[ 0.225359][ T19] audit: type=2000 audit(0.200:1): state=initialized audit_enabled=0 res=1
[ 0.233883][ T1] cpuidle: using governor menu
[ 0.239011][ T1] Feroceon L2: Enabling L2
[ 0.243295][ T1] Feroceon L2: Cache support initialised.
[ 0.257834][ T1] No ATAGs?
[ 0.618532][ T1] raid6: int32x8 gen() 152 MB/s
[ 0.958530][ T1] raid6: int32x4 gen() 140 MB/s
[ 1.298558][ T1] raid6: int32x2 gen() 180 MB/s
[ 1.638530][ T1] raid6: int32x1 gen() 131 MB/s
[ 1.643476][ T1] raid6: using algorithm int32x2 gen() 180 MB/s
[ 1.998531][ T1] raid6: .... xor() 114 MB/s, rmw enabled
[ 2.004084][ T1] raid6: using intx1 recovery algorithm
[ 2.019832][ T1] SCSI subsystem initialized
[ 2.028989][ T1] usbcore: registered new interface driver usbfs
[ 2.035193][ T1] usbcore: registered new interface driver hub
[ 2.058585][ T1] usbcore: registered new device driver usb
[ 2.064654][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.078531][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.088344][ T1] PTP clock support registered
[ 2.120301][ T1] vgaarb: loaded
[ 2.124378][ T1] clocksource: Switched to clocksource orion_clocksource
[ 2.141375][ T1] VFS: Disk quotas dquot_6.6.0
[ 2.164717][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.195658][ T1] NET: Registered PF_INET protocol family
[ 2.214473][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 2.234523][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 2.243776][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 2.264416][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 2.272769][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 2.294438][ T1] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.301993][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 2.324574][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 2.331792][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 2.355079][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 2.375041][ T1] RPC: Registered named UNIX socket transport module.
[ 2.381636][ T1] RPC: Registered udp transport module.
[ 2.394397][ T1] RPC: Registered tcp transport module.
[ 2.399770][ T1] RPC: Registered tcp-with-tls transport module.
[ 2.424392][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.431508][ T1] PCI: CLS 0 bytes, default 32
[ 2.446630][ T10] Trying to unpack rootfs image as initramfs...
[ 3.189961][ T10] Freeing initrd memory: 5656K
[ 3.412800][ T1] Initialise system trusted keyrings
[ 3.418904][ T1] Key type blacklist registered
[ 3.423885][ T1] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 3.431213][ T1] zbud: loaded
[ 3.448933][ T1] NFS: Registering the id_resolver key type
[ 3.454739][ T1] Key type id_resolver registered
[ 3.459596][ T1] Key type id_legacy registered
[ 3.464449][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 3.471822][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 3.481133][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 3.489518][ T1] fuse: init (API version 7.38)
[ 3.495343][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 3.502723][ T1] orangefs_init: module version upstream loaded
[ 3.509105][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 3.677190][ T1] xor: measuring software checksum speed
[ 3.689344][ T1] arm4regs : 1485 MB/sec
[ 3.705448][ T1] 8regs : 890 MB/sec
[ 3.718271][ T1] 32regs : 1263 MB/sec
[ 3.723297][ T1] xor: using function: arm4regs (1485 MB/sec)
[ 3.729210][ T1] async_tx: api initialized (async)
[ 3.734244][ T1] Key type asymmetric registered
[ 3.739031][ T1] Asymmetric key parser 'x509' registered
[ 3.784676][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 3.793070][ T1] io scheduler bfq registered
[ 3.939968][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 3.949577][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 3.960212][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 3.970606][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 3.980535][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 3.990656][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000
[ 4.000752][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[ 4.010841][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.021449][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.032048][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 4.042640][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 4.054146][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 4.062481][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.068686][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 4.079545][ T1] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff])
[ 4.090388][ T1] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[ 4.101228][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 4.108792][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 4.115858][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400
[ 4.123067][ T1] pci 0000:00:02.0: [11ab:6282] type 01 class 0x060400
[ 4.131823][ T1] PCI: bus0: Fast back to back transfers disabled
[ 4.138105][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.146800][ T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.155767][ T1] PCI: bus1: Fast back to back transfers enabled
[ 4.161928][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 4.169453][ T1] pci 0000:02:00.0: [1033:0194] type 00 class 0x0c0330
[ 4.176221][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x98000000-0x98001fff 64bit]
[ 4.183835][ T1] pci 0000:02:00.0: PME# supported from D0 D3hot
[ 4.190116][ T1] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:02.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 4.234471][ T1] PCI: bus2: Fast back to back transfers disabled
[ 4.240725][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 4.248061][ T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[ 4.255621][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 4.261272][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit]
[ 4.269272][ T1] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 4.274930][ T1] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 4.282641][ T1] pcieport 0000:00:02.0: enabling device (0140 -> 0142)
[ 4.290268][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 4.356359][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 4.368019][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 4.436344][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 4.448306][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 4.457455][ T1] printk: console [ttyS0] disabled
[ 4.462914][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 29, base_baud = 12500000) is a 16550A
[ 4.472647][ T1] printk: console [ttyS0] enabled
[ 4.472647][ T1] printk: console [ttyS0] enabled
[ 4.482496][ T1] printk: bootconsole [earlycon0] disabled
[ 4.482496][ T1] printk: bootconsole [earlycon0] disabled
[ 4.515882][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 30, base_baud = 12500000) is a 16550A
[ 4.536149][ T1] loop: module loaded
[ 4.541021][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 4.550593][ T1] scsi host0: sata_mv
[ 4.555771][ T1] scsi host1: sata_mv
[ 4.559988][ T1] ata1: SATA max UDMA/133 irq 31
[ 4.564866][ T1] ata2: SATA max UDMA/133 irq 31
[ 4.571733][ T1] spi-nor spi0.0: found m25p32, expected m25p80
[ 4.577939][ T1] spi-nor spi0.0: m25p32 (4096 Kbytes)
[ 4.583436][ T1] 6 fixed-partitions partitions found on MTD device spi0.0
[ 4.590546][ T1] Creating 6 MTD partitions on "spi0.0":
[ 4.596111][ T1] 0x000000000000-0x000000080000 : "RedBoot"
[ 4.602555][ T1] 0x000000080000-0x000000280000 : "zImage"
[ 4.608838][ T1] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 4.615046][ T1] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 4.621356][ T1] 0x0000003d0000-0x0000003f0000 : "RedBoot config"
[ 4.628337][ T1] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 4.635762][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 4.644334][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 4.658374][ T1] mdio_bus f1072004.mdio-bus-mii: MDIO device at address 8 is missing.
[ 4.684148][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 4.694213][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:3c:3b:5d
[ 4.704322][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 4.710630][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 4.719238][ T1] orion-ehci f1050000.ehci: irq 34, io mem 0xf1050000
[ 4.754408][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 4.761448][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 4.770485][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.778464][ T1] usb usb1: Product: EHCI Host Controller
[ 4.784064][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd
[ 4.791448][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 4.797797][ T1] hub 1-0:1.0: USB hub found
[ 4.802386][ T1] hub 1-0:1.0: 1 port detected
[ 4.808032][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 4.814041][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 4.822531][ T1] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004
[ 4.833007][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 4.839193][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 4.847412][ T1] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 4.854678][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 4.863715][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.871709][ T1] usb usb2: Product: xHCI Host Controller
[ 4.877348][ T1] usb usb2: Manufacturer: Linux 6.5.7-kirkwood-tld-1 xhci-hcd
[ 4.884727][ T1] usb usb2: SerialNumber: 0000:02:00.0
[ 4.890827][ T1] hub 2-0:1.0: USB hub found
[ 4.895367][ T52] ata1: SATA link down (SStatus 0 SControl F300)
[ 4.901682][ T1] hub 2-0:1.0: 2 ports detected
[ 4.907220][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.916357][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.05
[ 4.925405][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.933368][ T1] usb usb3: Product: xHCI Host Controller
[ 4.939124][ T1] usb usb3: Manufacturer: Linux 6.5.7-kirkwood-tld-1 xhci-hcd
[ 4.946494][ T1] usb usb3: SerialNumber: 0000:02:00.0
[ 4.952592][ T1] hub 3-0:1.0: USB hub found
[ 4.957157][ T1] hub 3-0:1.0: 2 ports detected
[ 4.962766][ T1] usbcore: registered new interface driver usb-storage
[ 4.970218][ T1] mousedev: PS/2 mouse device common for all mice
[ 4.976908][ T1] i2c_dev: i2c /dev entries driver
[ 4.984585][ T1] rtc-s35390a 0-0030: registered as rtc0
[ 4.990189][ T1] rtc-s35390a 0-0030: hctosys: unable to read the hardware clock
[ 4.999098][ T1] device-mapper: uevent: version 1.0.3
[ 5.004934][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 5.014737][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 5.022001][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 5.029587][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 5.037060][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 5.044688][ T1] ledtrig-cpu: registered to indicate activity on CPUs
[ 5.051542][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 5.057990][ T1] drop_monitor: Initializing network drop monitor service
[ 5.066439][ T1] NET: Registered PF_INET6 protocol family
[ 5.074006][ T1] Segment Routing with IPv6
[ 5.078542][ T1] RPL Segment Routing with IPv6
[ 5.083366][ T1] In-situ OAM (IOAM) with IPv6
[ 5.088345][ T1] NET: Registered PF_PACKET protocol family
[ 5.094529][ T1] Key type dns_resolver registered
[ 5.114092][ T1] registered taskstats version 1
[ 5.119250][ T1] Loading compiled-in X.509 certificates
[ 5.141916][ T1] Key type .fscrypt registered
[ 5.146853][ T1] Key type fscrypt-provisioning registered
[ 5.157647][ T1] Key type big_key registered
[ 5.198736][ T1] Key type encrypted registered
[ 5.254584][ T54] ata2: SATA link down (SStatus 0 SControl F300)
[ 5.292046][ T105] "cryptomgr_test" (105) uses obsolete ecb(arc4) skcipher
[ 5.474619][ T9] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 5.511292][ T9] usb 3-1: New USB device found, idVendor=174c, idProduct=5136, bcdDevice= 0.01
[ 5.534393][ T9] usb 3-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 5.542268][ T9] usb 3-1: Product: AS2105
[ 5.554394][ T9] usb 3-1: Manufacturer: ASMedia
[ 5.559212][ T9] usb 3-1: SerialNumber: 00000000000000000000
[ 5.577226][ T9] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 5.594898][ T9] scsi host2: usb-storage 3-1:1.0
[ 6.655759][ T18] scsi 2:0:0:0: Direct-Access ASMT 2105 0 PQ: 0 ANSI: 6
[ 6.675963][ T29] sd 2:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 6.694431][ T29] sd 2:0:0:0: [sda] Write Protect is off
[ 6.704423][ T29] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.728056][ T29] sda: sda1
[ 6.744545][ T29] sd 2:0:0:0: [sda] Attached SCSI disk
[ 7.110464][ T1] clk: Disabling unused clocks
[ 7.118467][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 7.134987][ T1] Checked W+X mappings: passed, no W+X pages found
[ 7.141386][ T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.17-1~deb12u1
[ 8.198270][ T152] usbcore: registered new interface driver uas
[ 9.634414][ T52] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 9.643732][ T52] ata1.00: ATA-11: Patriot P220 2048GB, H221215a, max UDMA/133
[ 9.651200][ T52] ata1.00: 4000797360 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 9.663506][ T52] ata1.00: configured for UDMA/133
[ 9.670155][ T9] scsi 0:0:0:0: Direct-Access ATA Patriot P220 204 215a PQ: 0 ANSI: 5
[ 9.683471][ T10] sd 0:0:0:0: [sdb] 4000797360 512-byte logical blocks: (2.05 TB/1.86 TiB)
[ 9.696604][ T10] sd 0:0:0:0: [sdb] Write Protect is off
[ 9.702225][ T10] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.712203][ T10] sd 0:0:0:0: [sdb] Preferred minimum I/O size 512 bytes
[ 9.724841][ T10] sdb: sdb1 sdb2 sdb3
[ 9.734105][ T10] sd 0:0:0:0: [sdb] Attached SCSI disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 20045/15630336 files, 1505286/62514518 blocks
done.
[ 23.823246][ T182] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 23.985591][ T182] EXT4-fs (sda1): mounted filesystem 5c69b81b-afd1-4cd3-94f4-2a94bedd7308 ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 26.753475][ T374] orion_wdt: Initial timeout 21 sec
[ 26.861535][ T361] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 26.994774][ T361] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 27.341719][ T365] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 28.364469][ C0] random: crng init done
done.
Activating swap:.
[ 28.918624][ T523] EXT4-fs (sda1): re-mounted 5c69b81b-afd1-4cd3-94f4-2a94bedd7308 r/w. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
Initializing random number generator...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:50:43:3c:3b:5d
Sending on LPF/eth0/00:50:43:3c:3b:5d
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
[ 34.617606][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPOFFER of 192.168.1.219 from 192.168.1.1
DHCPREQUEST for 192.168.1.219 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.1.219 from 192.168.1.1
bound to 192.168.1.219 -- renewal in 18665 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1033 (syslogd)
.
Not starting NFS kernel daemon: no exports ... (warning).
Starting system message bus: dbus.
Starting NTP server: ntpd2025-03-09T15:36:08 ntpd[1072]: INIT: ntpd ntpsec-1.2.2: Starting
2025-03-09T15:36:08 ntpd[1072]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106
.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting NTP server: ntpd.
Starting OpenBSD Secure Shell server: sshd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1057 (klogd)
.
Running local boot scripts (/etc/rc.local)
.
Debian GNU/Linux 12 debian ttyS0
debian login:
Thanks!
/BayPanard
|
Re: Debian on Synology DS112 March 11, 2025 12:48AM |
Admin Registered: 14 years ago Posts: 19,422 |
Bay,
So your current envs for booting is
1. See if you can boot with USB rootfs
Get the listing of stock envs (untouched)
And then enter these 3 envs (same as before)
2. Saving envs permanently
I'll come back for this.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
So your current envs for booting is
Marvell>> setenv ipaddr 192.168.1.128 Marvell>> setenv serverip 192.168.1.180 Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> mw 0x800000 0 1 Marvell>> tftpboot 0x800000 uImage Marvell>> tftpboot 0x2100000 uInitrd Marvell>> bootm 0x800000 0x2100000
1. See if you can boot with USB rootfs
Get the listing of stock envs (untouched)
printenv
And then enter these 3 envs (same as before)
Marvell>> setenv ipaddr 192.168.1.128 Marvell>> setenv serverip 192.168.1.180 Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'And then try USB approach
usb reset mw 0x800000 0 1 ext2load usb 0:1 0x800000 /boot/uImage ext2load usb 0:1 0x2100000 /boot/uInitrd bootm 0x800000 0x2100000
2. Saving envs permanently
I'll come back for this.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Synology DS112 March 11, 2025 12:18PM |
Registered: 5 weeks ago Posts: 18 |
Bodhi,
1. list of stock envs :
But that's as far as I could go, there is not ext2load on this u-boot .. :
Here are all available commands :
/BayPanard
1. list of stock envs :
Marvell>> printenv bootcmd=bootm F8080000 F8280000 baudrate=115200 loads_echo=0 ipaddr=192.168.1.154 serverip=192.168.1.155 rootpath=/mnt/ARM_FS/ netmask=255.255.254.0 run_diag=yes stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mtdparts=spi_flash:0x80000@0(uboot)ro,0x300000@0x100000(root) mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes MALLOC_len=1 ethprime=egiga0 netbsd_en=no vxworks_en=no bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; lcd0_enable=0 lcd0_params=640x480-16@60 bootdelay=3 disaMvPnp=no ethaddr=00:50:43:3c:3b:5d ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host pcieTune=no pcieTune1=no bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/sda1 rw syno_hw_version=DS112v10 ihd_num=0 netif_num=1 ethact=egiga0 Environment size: 1161/4092 bytes
But that's as far as I could go, there is not ext2load on this u-boot .. :
Marvell>> setenv ipaddr 192.168.1.128 Marvell>> setenv serverip 192.168.1.180 Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> usb reset Unknown command 'usb' - try 'help' Marvell>> mw 0x800000 0 1 Marvell>> ext2load Unknown command 'ext2load' - try 'help' Marvell>> ext2load usb 0:1 0x800000 /boot/uImage Unknown command 'ext2load' - try 'help'
Here are all available commands :
Marvell>> help ? - alias for 'help' WOLTest - Wake On Lan u-boot testing base - print or set address offset bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol bubt - Burn an image on the Boot Flash. cmp - memory compare cp - memory copy cpumap - Display CPU memory mapping settings. crc32 - checksum calculation echo - echo args to console erase - erase FLASH memory flinfo - print FLASH memory information go - start application at address 'addr' help - print online help icrc32 - checksum calculation iloop - infinite loop on address range imd - i2c memory display imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing) imw - memory write (fill) inm - memory modify (constant address) iprobe - probe to discover valid I2C chip addresses loop - infinite loop on address range md - memory display mm - memory modify (auto-incrementing) mtest - simple RAM test mw - memory write (fill) nm - memory modify (constant address) pci - list and access PCI Configuration Space phyRead - Read Phy register phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU resetenv - Return all environment variable to default. setenv - set environment variables sflash - read, write or erase the external SPI Flash. sg - scanning the PHYs status Temp - read chip Tj temp tftpboot- boot image via network using TFTP protocol version - print monitor version
/BayPanard
|
Re: Debian on Synology DS112 March 12, 2025 04:46AM |
Admin Registered: 14 years ago Posts: 19,422 |
Bay,
So this stock u-boot does not support USB or IDE command (not possible to boot with USB or SATA storage device). Continuing using stock u-boot means you'll need to set up to boot permanently with tftp, until I can roll a new u-boot for it. Not hard, but I can only do it when I have time.
To prepare for a permanent envs setting. Do this test boot a few times
And then after it boot into Debian, do a reboot (not shutdown). Repeat the test.
===
If all went well. You can then decide to set the envs permanently booting Debian, or dual boot Debian and stock DSM. We'll do that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
So this stock u-boot does not support USB or IDE command (not possible to boot with USB or SATA storage device). Continuing using stock u-boot means you'll need to set up to boot permanently with tftp, until I can roll a new u-boot for it. Not hard, but I can only do it when I have time.
To prepare for a permanent envs setting. Do this test boot a few times
setenv ipaddr 192.168.1.128 setenv serverip 192.168.1.180 setenv set_bootargs_debian 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv bootcmd_debian 'mw 0x800000 0 1; tftpboot 0x800000 uImage; tftpboot 0x2100000 uInitrd; run set_bootargs_debian; bootm 0x800000 0x2100000'and then
run bootcmd_debianAfter it booted into Debian, shutdown and repeat the test.
And then after it boot into Debian, do a reboot (not shutdown). Repeat the test.
===
If all went well. You can then decide to set the envs permanently booting Debian, or dual boot Debian and stock DSM. We'll do that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Synology DS112 March 12, 2025 10:40AM |
Registered: 5 weeks ago Posts: 18 |
|
Re: Debian on Synology DS112 March 12, 2025 11:15AM |
Admin Registered: 14 years ago Posts: 19,422 |
Bay,
> I did test your last commands but unfortunately my
> u-boot is missing the "run" command.
Damn! this u-boot is pathetic :) you also don't have the "source" command!
You could try this. If this u-boot accepts a long string for env then it's better (copy and paste one command instead of several envs).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I did test your last commands but unfortunately my
> u-boot is missing the "run" command.
Damn! this u-boot is pathetic :) you also don't have the "source" command!
You could try this. If this u-boot accepts a long string for env then it's better (copy and paste one command instead of several envs).
setenv bootcmd 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial; mw 0x800000 0 1; tftpboot 0x800000 uImage; tftpboot 0x2100000 uInitrd; bootm 0x800000 0x2100000'and then
boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
