|
Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 23, 2025 07:38AM |
Registered: 9 years ago Posts: 63 |
NSA3x0S> printenv arcNumber=4931 baudrate=115200 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320s.dtb ethact=egiga0 ethaddr=XX:XX:XX:XX:XX:XX fileaddr=800000 filesize=5ef848 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x2c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) partition=nand0,2 poke=mw.l f1010104 c70f0ffd preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi Environment size: 3297/131068 bytes
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700) ZyXEL NSA310S/320S 1/2-Bay Power Media Server SoC: Kirkwood 88F6702_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA3x0S> printenv poke; run poke; ide reset; sleep 60; usb start; boot poke=mw.l f1010104 c70f0ffd Reset IDE: Bus 0: OK Bus 1: .........OK Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6FC8VSV Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6JN55AL Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 3905536 06b4319f-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 661 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 6223944 bytes read in 1058 ms (5.6 MiB/s) loading uInitrd ... 5791271 bytes read in 947 ms (5.8 MiB/s) loading DTB /boot/dts/kirkwood-nsa320s.dtb ... 12802 bytes read in 1799 ms (6.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-6.5.7-kirkwood-tld-1 Created: 2023-10-31 22:53:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 6223880 Bytes = 5.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-6.5.7-kirkwood-tld-1 Created: 2023-10-31 22:53:55 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5791207 Bytes = 5.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02c00000 Booting using the fdt blob at 0x2c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f585000, end 0fb0ade7 ... OK Loading Device Tree to 0f57e000, end 0f584201 ... OK Starting kernel ... [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232336K/262144K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 29808K reserved, 0K cma-reserved) [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000002][ T0] sched_clock: 32 bits at 167MHz, resolution 6ns, wraps every 12884901885ns [ 0.000056][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.000738][ T0] Console: colour dummy device 80x30 [ 0.000819][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.000854][ T0] CPU: Testing write buffer coherency: ok [ 0.001006][ T0] pid_max: default: 32768 minimum: 301 [ 0.011516][ T0] LSM: initializing lsm=capability,integrity [ 0.014374][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.014415][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.028919][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.029331][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.029860][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.030330][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.030812][ T1] rcu: Hierarchical SRCU implementation. [ 0.030830][ T1] rcu: Max phase no-delay instances is 1000. [ 0.034300][ T1] devtmpfs: initialized [ 0.047022][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.047074][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.050636][ T1] prandom: seed boundary self test passed [ 0.055756][ T1] prandom: 100 self tests passed [ 0.055773][ T1] pinctrl core: initialized pinctrl subsystem [ 0.060878][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.061831][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.068196][ T1] audit: initializing netlink subsys (disabled) [ 0.070642][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.070827][ T19] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1 [ 0.070885][ T1] cpuidle: using governor ladder [ 0.070976][ T1] cpuidle: using governor menu [ 0.071732][ T1] Feroceon L2: Enabling L2 [ 0.071772][ T1] Feroceon L2: Cache support initialised. [ 0.084961][ T1] No ATAGs? [ 0.450075][ T1] raid6: int32x8 gen() 93 MB/s [ 0.790070][ T1] raid6: int32x4 gen() 92 MB/s [ 1.130103][ T1] raid6: int32x2 gen() 120 MB/s [ 1.470070][ T1] raid6: int32x1 gen() 93 MB/s [ 1.470084][ T1] raid6: using algorithm int32x2 gen() 120 MB/s [ 1.810072][ T1] raid6: .... xor() 76 MB/s, rmw enabled [ 1.810086][ T1] raid6: using intx1 recovery algorithm [ 1.812009][ T1] SCSI subsystem initialized [ 1.812884][ T1] usbcore: registered new interface driver usbfs [ 1.812964][ T1] usbcore: registered new interface driver hub [ 1.813038][ T1] usbcore: registered new device driver usb [ 1.813466][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.813477][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.813514][ T1] PTP clock support registered [ 1.816708][ T1] vgaarb: loaded [ 1.817663][ T1] clocksource: Switched to clocksource orion_clocksource [ 1.836525][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.837039][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.876012][ T1] NET: Registered PF_INET protocol family [ 1.876363][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.878969][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.879188][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.879223][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 1.879272][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 1.879328][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 1.880126][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.880409][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.880448][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.881479][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.888748][ T1] RPC: Registered named UNIX socket transport module. [ 1.888765][ T1] RPC: Registered udp transport module. [ 1.888772][ T1] RPC: Registered tcp transport module. [ 1.888779][ T1] RPC: Registered tcp-with-tls transport module. [ 1.888786][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.888810][ T1] PCI: CLS 0 bytes, default 32 [ 1.892153][ T32] Trying to unpack rootfs image as initramfs... [ 3.017073][ T32] Freeing initrd memory: 5656K [ 4.242602][ T1] Initialise system trusted keyrings [ 4.242708][ T1] Key type blacklist registered [ 4.244298][ T1] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 4.244500][ T1] zbud: loaded [ 4.267312][ T1] NFS: Registering the id_resolver key type [ 4.267407][ T1] Key type id_resolver registered [ 4.267418][ T1] Key type id_legacy registered [ 4.267647][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 4.267753][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 4.269646][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 4.270648][ T1] fuse: init (API version 7.38) [ 4.272379][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 4.272717][ T1] orangefs_init: module version upstream loaded [ 4.273190][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 4.527283][ T1] xor: measuring software checksum speed [ 4.537966][ T1] arm4regs : 927 MB/sec [ 4.555666][ T1] 8regs : 556 MB/sec [ 4.568169][ T1] 32regs : 789 MB/sec [ 4.568180][ T1] xor: using function: arm4regs (927 MB/sec) [ 4.568198][ T1] async_tx: api initialized (async) [ 4.568215][ T1] Key type asymmetric registered [ 4.568225][ T1] Asymmetric key parser 'x509' registered [ 4.627095][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 4.627619][ T1] io scheduler bfq registered [ 4.854905][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 4.857192][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 4.858972][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 4.860213][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 4.860308][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 4.860361][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 4.860395][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 4.861199][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 4.861221][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.861244][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 4.861263][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 4.861281][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 4.861414][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 4.863638][ T1] PCI: bus0: Fast back to back transfers disabled [ 4.863672][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.864006][ T1] PCI: bus1: Fast back to back transfers enabled [ 4.864032][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 4.864081][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 4.865304][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 4.930798][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.936341][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 5.000811][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 5.006719][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.009846][ T1] printk: console [ttyS0] disabled [ 5.010612][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 10416666) is a 16550A [ 5.010687][ T1] printk: console [ttyS0] enabled [ 6.011843][ T1] loop: module loaded [ 6.016938][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 6.027895][ T1] scsi host0: sata_mv [ 6.033579][ T1] scsi host1: sata_mv [ 6.037979][ T1] ata1: SATA max UDMA/133 irq 29 [ 6.042767][ T1] ata2: SATA max UDMA/133 irq 29 [ 6.049223][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 6.056262][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 6.061256][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 6.069548][ T1] Scanning device for bad blocks [ 6.079488][ T1] Bad eraseblock 100 at 0x000000c80000 [ 6.089893][ T1] Bad eraseblock 200 at 0x000001900000 [ 6.137247][ T1] 9 cmdlinepart partitions found on MTD device orion_nand [ 6.144212][ T1] Creating 9 MTD partitions on "orion_nand": [ 6.150056][ T1] 0x000000000000-0x000000100000 : "uboot" [ 6.156591][ T1] 0x000000100000-0x000000180000 : "stock_uboot_env" [ 6.163884][ T1] 0x000000180000-0x000000200000 : "key_store" [ 6.170686][ T1] 0x000000200000-0x000000280000 : "info" [ 6.177000][ T1] 0x000000280000-0x000000c80000 : "etc" [ 6.183330][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 6.190085][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 6.196888][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 6.203702][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 6.211610][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 6.220159][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 6.235639][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@1: Whitelisted compatible string. Please remove [ 6.272622][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.282693][ T1] mv643xx_eth: Set the PHY to fix link down [ 6.283842][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 6.299877][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 6.306132][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 6.314784][ T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000 [ 6.347692][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 6.354928][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05 [ 6.363923][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.371867][ T1] usb usb1: Product: EHCI Host Controller [ 6.377461][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd [ 6.384846][ T1] usb usb1: SerialNumber: f1050000.ehci [ 6.391524][ T1] hub 1-0:1.0: USB hub found [ 6.396014][ T1] hub 1-0:1.0: 1 port detected [ 6.401906][ T1] usbcore: registered new interface driver usb-storage [ 6.409313][ T1] mousedev: PS/2 mouse device common for all mice [ 6.416077][ T1] i2c_dev: i2c /dev entries driver [ 6.424461][ T1] ht1382 0-0068: registered as rtc0 [ 6.430824][ T1] ht1382 0-0068: setting system clock to 2025-02-23T13:14:57 UTC (1740316497) [ 6.441274][ T1] device-mapper: uevent: version 1.0.3 [ 6.447225][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 6.457247][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 6.464543][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 6.471864][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 6.479250][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 6.489933][ T1] ledtrig-cpu: registered to indicate activity on CPUs [ 6.496801][ T1] hid: raw HID events driver (C) Jiri Kosina [ 6.503186][ T1] drop_monitor: Initializing network drop monitor service [ 6.512035][ T1] NET: Registered PF_INET6 protocol family [ 6.520269][ T1] Segment Routing with IPv6 [ 6.524628][ T1] RPL Segment Routing with IPv6 [ 6.529524][ T1] In-situ OAM (IOAM) with IPv6 [ 6.534268][ T1] NET: Registered PF_PACKET protocol family [ 6.540660][ T1] Key type dns_resolver registered [ 6.547759][ T53] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 6.557220][ T53] ata1.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133 [ 6.577819][ T53] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 6.588042][ T53] ata1.00: configured for UDMA/133 [ 6.596299][ T1] registered taskstats version 1 [ 6.601465][ T1] Loading compiled-in X.509 certificates [ 6.607544][ T10] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5 [ 6.629668][ T32] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 6.647779][ T32] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.653815][ T32] sd 0:0:0:0: [sda] Write Protect is off [ 6.664290][ T32] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.675098][ T1] Key type .fscrypt registered [ 6.679760][ T1] Key type fscrypt-provisioning registered [ 6.686120][ T32] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.693152][ T50] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 6.707962][ T1] Key type big_key registered [ 6.764534][ T32] sda: [ 6.767455][ T32] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.777413][ T1] Key type encrypted registered [ 6.899669][ T50] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 [ 6.913758][ T50] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 6.922141][ T104] "cryptomgr_test" (104) uses obsolete ecb(arc4) skcipher [ 6.929191][ T50] usb 1-1: Product: USB2.0 Hub [ 6.938676][ T50] hub 1-1:1.0: USB hub found [ 6.948171][ T50] hub 1-1:1.0: 4 ports detected [ 7.137709][ T55] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.157870][ T55] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133 [ 7.165253][ T55] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 7.190308][ T55] ata2.00: configured for UDMA/133 [ 7.216044][ T18] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5 [ 7.239497][ T32] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 7.257713][ T32] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 7.263711][ T32] sd 1:0:0:0: [sdb] Write Protect is off [ 7.277711][ T50] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 7.285498][ T32] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.307828][ T32] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 7.360075][ T32] sdb: sdb1 sdb2 sdb3 [ 7.369231][ T32] sd 1:0:0:0: [sdb] Attached SCSI disk [ 7.519539][ T50] usb 1-1.1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 2.00 [ 7.537687][ T50] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.545669][ T50] usb 1-1.1: Product: DataTraveler 2.0 [ 7.567684][ T50] usb 1-1.1: Manufacturer: Kingston [ 7.572730][ T50] usb 1-1.1: SerialNumber: 0017318974D91FC0693A4974 [ 7.589339][ T50] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 7.608408][ T50] scsi host2: usb-storage 1-1.1:1.0 [ 8.649884][ T32] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 0000 PQ: 0 ANSI: 4 [ 8.670959][ T18] sd 2:0:0:0: [sdc] 30273600 512-byte logical blocks: (15.5 GB/14.4 GiB) [ 8.689578][ T18] sd 2:0:0:0: [sdc] Write Protect is off [ 8.707702][ T18] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.737932][ T18] sdc: sdc1 [ 8.748005][ T18] sd 2:0:0:0: [sdc] Attached SCSI removable disk [ 9.898232][ T18] kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp33 [ 9.907357][ T18] pinctrl core: failed to register map default (0): invalid type given [ 9.916351][ T1] clk: Disabling unused clocks [ 9.924524][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 9.948656][ T1] Checked W+X mappings: passed, no W+X pages found [ 9.955013][ T1] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.17-1~deb12u1 [ 11.723794][ T155] usbcore: registered new interface driver uas [ 13.047716][ T121] usb 1-1.1: reset high-speed USB device number 3 using orion-ehci [ 13.203860][ T121] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=1s [ 13.213808][ T121] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 00 00 02 08 00 00 f0 00 [ 13.221829][ T121] I/O error, dev sdc, sector 520 op 0x0:(READ) flags 0x84700 phys_seg 2 prio class 2 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.38.1 [/sbin/fsck.ext3 (1) -- /dev/sdc1] fsck.ext3 -a -C0 /dev/sdc1 rootfs: recovering journal [ 38.781671][ T121] random: crng init done rootfs: Clearing orphaned inode 43428 (uid=0, gid=0, mode=0100644, size=313264) rootfs: clean, 20075/122160 files, 218978/488192 blocks done. [ 72.888984][ T180] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem [ 72.935344][ T180] EXT4-fs (sdc1): mounted filesystem bcf22700-38c8-477c-9969-e26f648c6e27 ro with ordered data mode. Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 3.06 booting INIT: No inittab.d directory found Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 76.570955][ T359] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 77.130978][ T358] orion_wdt: Initial timeout 25 sec [ 77.512515][ T361] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 77.671161][ T361] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 77.776786][ T361] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 77.898282][ T360] marvell-cesa f1030000.crypto: CESA device successfully registered [ 78.236835][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.279851][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.316854][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.359826][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.396826][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.407815][ T121] usb 1-1-port1: Cannot enable. Maybe the USB cable is bad? [ 78.460829][ T121] usb 1-1-port1: cannot disable (err = -71) [ 78.497821][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.534822][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.577863][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.613825][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.659830][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.665416][ T121] usb 1-1-port1: Cannot enable. Maybe the USB cable is bad? [ 78.719838][ T121] usb 1-1-port1: cannot disable (err = -71) [ 78.756838][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.797889][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.834850][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.879847][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.915838][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.927807][ T121] usb 1-1-port1: Cannot enable. Maybe the USB cable is bad? [ 78.967840][ T121] usb 1-1-port1: cannot disable (err = -71) [ 79.004849][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.049837][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.086826][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.129832][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.166834][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.177827][ T121] usb 1-1-port1: Cannot enable. Maybe the USB cable is bad? [ 79.217842][ T121] usb 1-1-port1: cannot disable (err = -71) [ 79.254830][ T121] usb 1-1-port1: cannot disable (err = -71) [ 79.267879][ T121] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=1s [ 79.284900][ T121] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 01 cd f0 3a 00 00 01 00 [ 79.307726][ T121] I/O error, dev sdc, sector 30273594 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 79.323844][ T50] hub 1-1:1.0: hub_ext_port_status failed (err = -71) [ 79.517849][ T121] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s [ 79.536622][ T121] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 01 cd f0 38 00 00 01 00 [ 79.557732][ T121] I/O error, dev sdc, sector 30273592 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 79.567126][ T121] Buffer I/O error on dev sdc, logical block 3784199, async page read [ 79.847870][ T365] sdc: detected capacity change from 30273600 to 0 [ 79.898172][ T364] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 79.904800][ T364] I/O error, dev sdc, sector 1922696 op 0x0:(READ) flags 0x80700 phys_seg 17 prio class 2 [ 80.077916][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.084544][ T33] I/O error, dev sdc, sector 1922768 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 80.094073][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.100717][ T33] I/O error, dev sdc, sector 1922768 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 done. [ 80.587863][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.594485][ T199] I/O error, dev sdc, sector 2497840 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 80.607879][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.614504][ T33] I/O error, dev sdc, sector 2497840 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 mountdevsubfs.sh: Input/output e[ 80.627880][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device rror [ 80.635084][ T199] I/O error, dev sdc, sector 1994488 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2 [ 80.647087][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.653858][ T33] I/O error, dev sdc, sector 1994488 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 checkroot.sh: Input/output error[ 80.665626][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.673555][ T199] I/O error, dev sdc, sector 1994432 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 80.685121][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device checkfs.sh: Input/output error [ 80.694213][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.705410][ T435] sd 2:0:0:0: [sdc] tag#0 access beyond end of device checkroot-bootclean.sh: Input/ou[ 80.715976][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device tput error [ 80.726181][ T436] sd 2:0:0:0: [sdc] tag#0 access beyond end of device kmod: Input/output error [ 80.736790][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.746505][ T437] sd 2:0:0:0: [sdc] tag#0 access beyond end of device mount-configfs: Input/output err[ 80.757212][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device or [ 80.767362][ T438] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.778155][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.788231][ T439] sd 2:0:0:0: [sdc] tag#0 access beyond end of device mountall-bootclean.sh: Input/out[ 80.798889][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device put error [ 80.808918][ T440] sd 2:0:0:0: [sdc] tag#0 access beyond end of device brightness: Input/output error [ 80.819625][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.829564][ T441] sd 2:0:0:0: [sdc] tag#0 access beyond end of device procps: Input/output error [ 80.840226][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.850037][ T442] sd 2:0:0:0: [sdc] tag#0 access beyond end of device urandom: Input/output error [ 80.860761][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.870607][ T443] sd 2:0:0:0: [sdc] tag#0 access beyond end of device networking: Input/output error [ 80.881618][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.891887][ T444] sd 2:0:0:0: [sdc] tag#0 access beyond end of device rpcbind: Input/output error [ 80.902592][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.912514][ T445] sd 2:0:0:0: [sdc] tag#0 access beyond end of device nfs-common: Input/output error [ 80.923148][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.933426][ T446] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.944140][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.954325][ T447] sd 2:0:0:0: [sdc] tag#0 access beyond end of device mountnfs-bootclean.sh: Input/out[ 80.965000][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device put error [ 80.975225][ T448] sd 2:0:0:0: [sdc] tag#0 access beyond end of device bootmisc.sh: Input/output error INIT: Entering runlevel: 2ned failure: mountdevsubfs.sh checkroo Using makefile-style concurrent boot in runlevel 2. [ 81.134052][ T454] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 81.141029][ T454] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 81.148137][ T454] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 81.154763][ T454] EXT4-fs warning (device sdc1): htree_dirblock_to_tree:1082: inode #98699: lblock 0: comm startpar: error -5 reading directory block [ 81.174417][ T455] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 81.181237][ T455] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.221593][ T456] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.261639][ T457] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.301606][ T458] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.341627][ T459] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.381611][ T460] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.421650][ T461] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.461604][ T462] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.501607][ T463] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.541601][ T464] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" INIT: Id "T0" respawning too fast: disabled for 5 minutes INIT: no more processes left in this runlevel
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 23, 2025 11:22AM |
Admin Registered: 14 years ago Posts: 19,425 |
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 23, 2025 03:57PM |
Registered: 2 years ago Posts: 98 |
$ uptime 15:30:20 up 14 days, 16:01, 1 user, load average: 0.18, 0.12, 0.09
$ lsblk -f NAME FSTYPE FSVER LABEL UUID FSAVAIL FSUSE% MOUNTPOINTS sda `-sda1 ext3 1.0 rootfs 5ed5229a-3eb5-4809-9670-31c452de653f 24.3G 12% / sdb `-sdb1 ext4 1.0 data1 c3a146d5-fe36-4e10-83a5-bff195993f78 2.4T 5% /media/d1 sdc `-sdc1 ext4 1.0 data2 4801ffaa-46d4-4fb1-8e12-0e5712b5c3e5 2.5T 0% /media/d2
$ ls /media/d1/ ls: reading directory '/media/d1/': Input/output errorthen unmount/remount it
root@nsa320s:~# umount /media/d1
root@nsa320s:~# mount /dev/sdb1 /media/d1/
mount: /media/d1: can't read superblock on /dev/sdb1.
dmesg(1) may have more information after failed mount system call.
Luckily, a reboot solved that issue:
$ ls /media/d1 lost+found off_work
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 23, 2025 10:21PM |
Admin Registered: 14 years ago Posts: 19,425 |
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 23, 2025 10:30PM |
Registered: 2 years ago Posts: 98 |
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 24, 2025 11:06AM |
Admin Registered: 14 years ago Posts: 19,425 |
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 24, 2025 01:01PM |
Registered: 9 years ago Posts: 63 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700)
ZyXEL NSA310S/320S 1/2-Bay Power Media Server
SoC: Kirkwood 88F6702_A1
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot: 0
NSA3x0S> pritnenv
Unknown command 'pritnenv' - try 'help'
NSA3x0S> printenv
arcNumber=4931
baudrate=115200
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=ttyS0,115200
device=0:1
devices=usb
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-nsa320s.dtb
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
fileaddr=800000
filesize=5ef848
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x2c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
partition=nand0,2
poke=mw.l f1010104 c70f0ffd
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
Environment size: 3297/131068 bytes
NSA3x0S> run poke; ide reset; boot
Reset IDE: Bus 0: OK Bus 1: .........OK
Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6FC8VSV
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6JN55AL
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 30027776 38ed2ab7-01 83 Boot
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
0 bytes read in 2521 ms (0 Bytes/s)
importing envs ...
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 2644 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
5890328 bytes read in 24970 ms (229.5 KiB/s)
loading uInitrd ...
11616046 bytes read in 3043 ms (3.6 MiB/s)
loading DTB /boot/dts/kirkwood-nsa320s.dtb ...
13335 bytes read in 4566 ms (2 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-6.12.6-kirkwood-tld-1
Created: 2025-02-17 19:14:45 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5890264 Bytes = 5.6 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-6.12.6-kirkwood-tld-1
Created: 2025-02-17 19:15:19 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 11615982 Bytes = 11.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02c00000
Booting using the fdt blob at 0x2c00000
Loading Kernel Image ... OK
Loading Ramdisk to 0eff7000, end 0fb0aeee ... OK
Loading Device Tree to 0eff0000, end 0eff6416 ... OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.12.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 PREEMPT Thu Dec 19 14:57:30 PST 2024
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
[ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65536
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[ 0.000000][ T0] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000003][ T0] sched_clock: 32 bits at 167MHz, resolution 6ns, wraps every 12884901885ns
[ 0.000058][ T0] Switching to timer-based delay loop, resolution 6ns
[ 0.001034][ T0] Console: colour dummy device 80x30
[ 0.001200][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.001233][ T0] CPU: Testing write buffer coherency: ok
[ 0.001384][ T0] pid_max: default: 32768 minimum: 301
[ 0.011786][ T0] LSM: initializing lsm=capability
[ 0.014124][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.014164][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.052816][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.053230][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.053832][ T1] rcu: Hierarchical SRCU implementation.
[ 0.053849][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.055965][ T1] Memory: 226060K/262144K available (11264K kernel code, 1614K rwdata, 5280K rodata, 1024K init, 323K bss, 34464K reserved, 0K cma-reserved)
[ 0.058204][ T1] devtmpfs: initialized
[ 0.071647][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.071694][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.080637][ T1] prandom: seed boundary self test passed
[ 0.085758][ T1] prandom: 100 self tests passed
[ 0.085776][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.091584][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.092530][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.094296][ T1] audit: initializing netlink subsys (disabled)
[ 0.096754][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.096929][ T22] audit: type=2000 audit(0.090:1): state=initialized audit_enabled=0 res=1
[ 0.096994][ T1] cpuidle: using governor ladder
[ 0.097079][ T1] cpuidle: using governor menu
[ 0.097841][ T1] Feroceon L2: Enabling L2
[ 0.097882][ T1] Feroceon L2: Cache support initialised.
[ 0.112943][ T1] No ATAGs?
[ 0.500078][ T1] raid6: int32x8 gen() 93 MB/s
[ 0.840074][ T1] raid6: int32x4 gen() 92 MB/s
[ 1.180078][ T1] raid6: int32x2 gen() 125 MB/s
[ 1.520073][ T1] raid6: int32x1 gen() 94 MB/s
[ 1.520087][ T1] raid6: using algorithm int32x2 gen() 125 MB/s
[ 1.860078][ T1] raid6: .... xor() 75 MB/s, rmw enabled
[ 1.860091][ T1] raid6: using intx1 recovery algorithm
[ 1.862179][ T1] SCSI subsystem initialized
[ 1.863165][ T1] usbcore: registered new interface driver usbfs
[ 1.863318][ T1] usbcore: registered new interface driver hub
[ 1.863393][ T1] usbcore: registered new device driver usb
[ 1.863774][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.863784][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.863820][ T1] PTP clock support registered
[ 1.870151][ T1] vgaarb: loaded
[ 1.871060][ T1] clocksource: Switched to clocksource orion_clocksource
[ 1.892736][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.893292][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.941512][ T1] NET: Registered PF_INET protocol family
[ 1.941838][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 1.944355][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.944573][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.945780][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 1.945833][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 1.945890][ T1] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.946614][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.946900][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.947043][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.948201][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.949999][ T1] RPC: Registered named UNIX socket transport module.
[ 1.950015][ T1] RPC: Registered udp transport module.
[ 1.950022][ T1] RPC: Registered tcp transport module.
[ 1.950028][ T1] RPC: Registered tcp-with-tls transport module.
[ 1.950035][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.950057][ T1] PCI: CLS 0 bytes, default 32
[ 1.950704][ T35] Trying to unpack rootfs image as initramfs...
[ 5.201697][ T1] Initialise system trusted keyrings
[ 5.201953][ T1] Key type blacklist registered
[ 5.202397][ T1] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 5.202538][ T1] zbud: loaded
[ 5.244192][ T1] NFS: Registering the id_resolver key type
[ 5.244257][ T1] Key type id_resolver registered
[ 5.244268][ T1] Key type id_legacy registered
[ 5.244501][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 5.244526][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 5.245941][ T1] fuse: init (API version 7.41)
[ 5.916733][ T1] xor: measuring software checksum speed
[ 5.920318][ T1] arm4regs : 920 MB/sec
[ 5.931128][ T1] 8regs : 548 MB/sec
[ 5.935330][ T1] 32regs : 785 MB/sec
[ 5.935340][ T1] xor: using function: arm4regs (920 MB/sec)
[ 5.935362][ T1] async_tx: api initialized (async)
[ 5.935382][ T1] Key type asymmetric registered
[ 5.935392][ T1] Asymmetric key parser 'x509' registered
[ 7.626398][ T35] Freeing initrd memory: 11344K
[ 7.686023][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 7.686596][ T1] io scheduler bfq registered
[ 7.913634][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 7.916003][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 7.917634][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 7.934774][ T1] ledtrig-cpu: registered to indicate activity on CPUs
[ 7.935347][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 7.935443][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 7.935496][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 7.935531][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 7.936424][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 7.936450][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 7.936473][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 7.936492][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 7.936509][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 7.936721][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 PCIe Root Port
[ 7.936766][ T1] pci 0000:00:01.0: PCI bridge to [bus 00]
[ 7.936787][ T1] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 7.936804][ T1] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 7.937505][ T1] /mbus@f1000000/pcie@82000000/pcie@1,0: Fixed dependency cycle(s) with /mbus@f1000000/pcie@82000000/pcie@1,0/interrupt-controller
[ 7.939011][ T1] PCI: bus0: Fast back to back transfers disabled
[ 7.939043][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 7.939420][ T1] PCI: bus1: Fast back to back transfers enabled
[ 7.939446][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 7.939499][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 7.939527][ T1] pci_bus 0000:00: resource 4 [mem 0xf1040000-0xf1041fff]
[ 7.939546][ T1] pci_bus 0000:00: resource 5 [mem 0xe0000000-0xefffffff]
[ 7.939562][ T1] pci_bus 0000:00: resource 6 [io 0x1000-0xeffff]
[ 7.940669][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 8.003417][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 8.008765][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 8.053301][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 8.059003][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 8.062254][ T1] printk: legacy console [ttyS0] disabled
[ 8.063187][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 10416666) is a 16550A
[ 8.063275][ T1] printk: legacy console [ttyS0] enabled
[ 9.099500][ T1] loop: module loaded
[ 9.104641][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 9.115505][ T1] scsi host0: sata_mv
[ 9.121398][ T1] scsi host1: sata_mv
[ 9.125729][ T1] ata1: SATA max UDMA/133 irq 29 lpm-pol 0
[ 9.131428][ T1] ata2: SATA max UDMA/133 irq 29 lpm-pol 0
[ 9.138585][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
[ 9.145719][ T1] nand: Eon NAND 128MiB 3,3V 8-bit
[ 9.150676][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 9.159071][ T1] Scanning device for bad blocks
[ 9.169068][ T1] Bad eraseblock 100 at 0x000000c80000
[ 9.179504][ T1] Bad eraseblock 200 at 0x000001900000
[ 9.226979][ T1] 9 cmdlinepart partitions found on MTD device orion_nand
[ 9.233945][ T1] Creating 9 MTD partitions on "orion_nand":
[ 9.239769][ T1] 0x000000000000-0x000000100000 : "uboot"
[ 9.246519][ T1] 0x000000100000-0x000000180000 : "stock_uboot_env"
[ 9.253835][ T1] 0x000000180000-0x000000200000 : "key_store"
[ 9.260561][ T1] 0x000000200000-0x000000280000 : "info"
[ 9.266898][ T1] 0x000000280000-0x000000c80000 : "etc"
[ 9.273195][ T1] 0x000000c80000-0x000001680000 : "kernel_1"
[ 9.279957][ T1] 0x000001680000-0x000004640000 : "rootfs1"
[ 9.286866][ T1] 0x000004640000-0x000005040000 : "kernel_2"
[ 9.293635][ T1] 0x000005040000-0x000008000000 : "rootfs2"
[ 9.302056][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 9.310569][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 9.352135][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 9.364318][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51
[ 9.374608][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 9.380883][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 9.389594][ T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000
[ 9.411096][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 9.418283][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 9.427278][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.435229][ T1] usb usb1: Product: EHCI Host Controller
[ 9.440831][ T1] usb usb1: Manufacturer: Linux 6.12.6-kirkwood-tld-1 ehci_hcd
[ 9.448263][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 9.455037][ T1] hub 1-0:1.0: USB hub found
[ 9.459542][ T1] hub 1-0:1.0: 1 port detected
[ 9.465428][ T1] usbcore: registered new interface driver usb-storage
[ 9.472780][ T1] i2c_dev: i2c /dev entries driver
[ 9.481211][ T1] ht1382 0-0068: registered as rtc0
[ 9.487366][ T1] ht1382 0-0068: setting system clock to 2025-02-24T18:39:09 UTC (1740422349)
[ 9.498028][ T1] device-mapper: uevent: version 1.0.3
[ 9.504202][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev
[ 9.514618][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 9.521914][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 9.529207][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 9.536677][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 9.544501][ T1] sdhci: Secure Digital Host Controller Interface driver
[ 9.551403][ T1] sdhci: Copyright(c) Pierre Ossman
[ 9.556688][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 9.563095][ T1] drop_monitor: Initializing network drop monitor service
[ 9.572164][ T1] NET: Registered PF_INET6 protocol family
[ 9.580994][ T1] Segment Routing with IPv6
[ 9.585405][ T1] RPL Segment Routing with IPv6
[ 9.590216][ T1] In-situ OAM (IOAM) with IPv6
[ 9.595038][ T1] NET: Registered PF_PACKET protocol family
[ 9.601542][ T1] Key type dns_resolver registered
[ 9.611194][ T58] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 9.622810][ T58] ata1.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 9.630201][ T58] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 9.654041][ T58] ata1.00: configured for UDMA/133
[ 9.659261][ T1] registered taskstats version 1
[ 9.664671][ T1] Loading compiled-in X.509 certificates
[ 9.675218][ T11] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5
[ 9.686378][ T21] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 9.701178][ T21] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 9.707195][ T21] sd 0:0:0:0: [sda] Write Protect is off
[ 9.731339][ T21] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.741125][ T57] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 9.761348][ T21] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[ 9.784490][ T1] Key type .fscrypt registered
[ 9.789124][ T1] Key type fscrypt-provisioning registered
[ 9.801005][ T1] Key type big_key registered
[ 9.858390][ T21] sda:
[ 9.861353][ T21] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.933128][ T57] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32
[ 9.951228][ T57] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 9.964263][ T57] usb 1-1: Product: USB2.0 Hub
[ 9.980637][ T57] hub 1-1:1.0: USB hub found
[ 9.990778][ T57] hub 1-1:1.0: 4 ports detected
[ 10.099357][ T1] Key type encrypted registered
[ 10.164764][ T112] "cryptomgr_test" (112) uses obsolete ecb(arc4) skcipher
[ 10.171825][ T60] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 10.221598][ T60] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 10.229006][ T60] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 10.271275][ T11] kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp33
[ 10.280417][ T11] pinctrl core: failed to register map default (0): invalid type given
[ 10.292347][ T60] ata2.00: configured for UDMA/133
[ 10.328336][ T35] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5
[ 10.361742][ T1] clk: Disabling unused clocks
[ 10.373182][ T11] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 10.404131][ T11] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 10.410150][ T11] sd 1:0:0:0: [sdb] Write Protect is off
[ 10.451271][ T11] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.481208][ T11] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[ 10.582035][ T11] sdb: sdb1 sdb2 sdb3
[ 10.587335][ T11] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 10.614415][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 10.642351][ T1] Checked W+X mappings: passed, no W+X pages found
[ 10.648800][ T1] Run /init as init process
[ 10.821293][ T57] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
Loading, please wait...
[ 10.998864][ T57] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00
[ 11.008022][ T57] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 11.031913][ T57] usb 1-1.1: Product: Ultra Fit
[ 11.036653][ T57] usb 1-1.1: Manufacturer: SanDisk
[ 11.088529][ T57] usb 1-1.1: SerialNumber: 4C530001110428108391
[ 11.111599][ T57] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 11.150260][ T57] scsi host2: usb-storage 1-1.1:1.0
[ 11.303173][ T157] udevd[157]: starting version 3.2.12
[ 12.255213][ T21] scsi 2:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6
[ 12.273276][ T11] sd 2:0:0:0: [sdc] 30031250 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 12.308763][ T11] sd 2:0:0:0: [sdc] Write Protect is off
[ 12.336138][ T11] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 12.419375][ T11] sdc: sdc1
[ 12.441367][ T11] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 13.281122][ C0] random: crng init done
[ 13.322618][ T158] udevd[158]: starting eudev-3.2.12
[ 13.531166][ T160] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 13.551231][ T160] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 13.591178][ T160] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 13.818164][ T162] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 14.993201][ T168] usbcore: registered new interface driver uas
[ 15.436070][ T176] block device autoloading is deprecated and will be removed.
[ 15.506713][ T169] udevd[169]: '/sbin/mdadm --incremental --export /dev/sdb3 --offroot /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WCC4N6JN55AL-part3 /dev/disk/by-id/wwn-0x50014ee264cc6a15-part3 /dev/disk/by-partuuid/798a5e17-f6de-45e9-adff-6d4403507148' [176] terminated by signal 11 (Segmentation fault)
[ 15.812576][ T154] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[ 15.822618][ T154] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 01 ca 3b 40 00 00 08 00
[ 15.830694][ T154] I/O error, dev sdc, sector 30030656 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 15.840487][ T8] usb 1-1.1: USB disconnect, device number 3
[ 15.849660][ T8] Buffer I/O error on dev sdc, logical block 15015328, async page read
[ 15.861198][ T168] Buffer I/O error on dev sdc, logical block 15015329, async page read
[ 15.869331][ T168] udevd: attempt to access beyond end of device
[ 15.869331][ T168] sdc: rw=0, sector=30030660, nr_sectors = 2 limit=0
[ 15.883684][ T168] Buffer I/O error on dev sdc, logical block 15015330, async page read
[ 15.893707][ T168] udevd: attempt to access beyond end of device
[ 15.893707][ T168] sdc: rw=0, sector=30030662, nr_sectors = 2 limit=0
[ 15.912052][ T168] Buffer I/O error on dev sdc, logical block 15015331, async page read
[ 16.221115][ T8] usb 1-1.1: new high-speed USB device number 4 using orion-ehci
[ 16.342613][ T8] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00
[ 16.351693][ T8] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 16.359707][ T8] usb 1-1.1: Product: Ultra Fit
[ 16.364428][ T8] usb 1-1.1: Manufacturer: SanDisk
[ 16.369381][ T8] usb 1-1.1: SerialNumber: 4C530001110428108391
[ 16.376825][ T8] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 16.387037][ T8] scsi host2: usb-storage 1-1.1:1.0
[ 17.442930][ T21] scsi 2:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6
[ 17.454491][ T21] scsi 2:0:0:0: Attached scsi generic sg2 type 0
[ 17.469146][ T11] sd 2:0:0:0: [sdc] 30031250 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 17.481269][ T11] sd 2:0:0:0: [sdc] Write Protect is off
[ 17.487516][ T11] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 17.535881][ T11] sdc: sdc1
[ 17.539611][ T11] sd 2:0:0:0: [sdc] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext4 (1) -- /dev/sdc1] fsck.ext4 -a -C0 /dev/sdc1
rootfs: clean, 65739/938400 files, 646444/3753472 blocks
done.
[ 37.057292][ T217] EXT4-fs (sdc1): mounted filesystem e98cc544-55aa-445f-8155-aecac62bc3f0 ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Starting hot-plug events dispatcher: udevd[ 39.353870][ T391] udevd[391]: starting version 3.2.12
[ 39.506218][ T392] udevd[392]: starting eudev-3.2.12
.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 40.812920][ T396] orion_wdt: Initial timeout 25 sec
[ 41.062158][ T410] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 41.762680][ T179] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[ 41.773741][ T8] usb 1-1.1: USB disconnect, device number 4
[ 41.788068][ T8] EXT4-fs (sdc1): shut down requested (2)
[ 41.801240][ T179] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 00 35 58 00 00 00 f0 00
[ 41.809266][ T179] I/O error, dev sdc, sector 3495936 op 0x0:(READ) flags 0x84700 phys_seg 2 prio class 0
[ 41.831128][ T8] Aborting journal on device sdc1-8.
[ 41.851156][ T394] device offline error, dev sdc, sector 3496176 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 41.871199][ T394] device offline error, dev sdc, sector 3496064 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 41.891201][ T394] device offline error, dev sdc, sector 3496064 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 41.912895][ T458] device offline error, dev sdc, sector 8963280 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 41.931361][ T434] device offline error, dev sdc, sector 4824120 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 41.944025][ T392] udevd[392]: worker [394] terminated by signal 7 (Bus error)
[ 41.951449][ T392] udevd[392]: worker [394] failed while handling '/devices/platform/ocp@f1000000/f1050000.ehci/usb1/1-1/1-1.1'
[ 41.963089][ T8] device offline error, dev sdc, sector 12854448 op 0x1:(WRITE) flags 0x9800 phys_seg 1 prio class 0
[ 41.974223][ T8] Buffer I/O error on dev sdc1, logical block 1606550, lost sync page write
[ 41.982957][ T37] device offline error, dev sdc, sector 972264 op 0x0:(READ) flags 0x84700 phys_seg 2 prio class 0
[ 41.993547][ T401] device offline error, dev sdc, sector 972504 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 42.004155][ T8] JBD2: I/O error when updating journal superblock for sdc1-8.
[ 42.011639][ T454] device offline error, dev sdc, sector 8486584 op 0x0:(READ) flags 0x3000 phys_seg 1 prio class 0
[ 42.032520][ T456] udevd[456]: failed to execute '/lib/udev/hdparm' '/lib/udev/hdparm': Input/output error
[ 42.048120][ T458] udevd[458]: failed to execute '/lib/udev/hdparm' '/lib/udev/hdparm': Input/output error
[ 42.061967][ T454] udevd[454]: failed to execute '/usr/libexec/nfsrahead' '/usr/libexec/nfsrahead 7:0': Input/output error
[ 42.075064][ T455] udevd[455]: failed to execute '/usr/libexec/nfsrahead' '/usr/libexec/nfsrahead 7:1': Input/output error
[ 42.088821][ T457] udevd[457]: failed to execute '/usr/libexec/nfsrahead' '/usr/libexec/nfsrahead 7:2': Input/output error
[ 42.101042][ T460] udevd[460]: failed to execute '/usr/libexec/nfsrahead' '/usr/libexec/nfsrahead 7:3': Input/output error
[ 42.102141][ T459] udevd[459]: failed to execute '/usr/libexec/nfsrahead' '/usr/libexec/nfsrahead 7:4': Input/output error
[ 42.361284][ T8] usb 1-1.1: new high-speed USB device number 5 using orion-ehci
[ 42.482868][ T8] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00
[ 42.501270][ T8] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 42.509280][ T8] usb 1-1.1: Product: Ultra Fit
[ 42.525157][ T8] usb 1-1.1: Manufacturer: SanDisk
[ 42.530175][ T8] usb 1-1.1: SerialNumber: 4C530001110428108391
[ 42.549993][ T8] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 42.565731][ T8] scsi host3: usb-storage 1-1.1:1.0
[ 42.576093][ T392] EXT4-fs warning (device sdc1): dx_probe:823: inode #652801: lblock 0: comm udevd: error -5 reading directory block
[ 42.612391][ T392] EXT4-fs warning (device sdc1): dx_probe:823: inode #652801: lblock 0: comm udevd: error -5 reading directory block
[ 42.626001][ T392] EXT4-fs warning (device sdc1): dx_probe:823: inode #652801: lblock 0: comm udevd: error -5 reading directory block
[ 42.662460][ T392] EXT4-fs warning (device sdc1): dx_probe:823: inode #652801: lblock 0: comm udevd: error -5 reading directory block
[ 42.674986][ T392] EXT4-fs warning (device sdc1): dx_probe:823: inode #652801: lblock 0: comm udevd: error -5 reading directory block
[ 42.687655][ T392] EXT4-fs warning (device sdc1): dx_probe:823: inode #652801: lblock 0: comm udevd: error -5 reading directory block
[ 42.700091][ T392] EXT4-fs warning (device sdc1): dx_probe:823: inode #652801: lblock 0: comm udevd: error -5 reading directory block
done.
mountdevsubfs.sh: Input/output error
checkroot.sh: Input/output error
checkfs.sh: Input/output error
checkroot-bootclean.sh: Input/output error
kmod: Input/output error
mountall.sh: Input/output error
mount-configfs: Input/output error
mountall-bootclean.sh: Input/output error
brightness: Input/output error
procps: Input/output error
urandom: Input/output error
networking: Input/output error
rpcbind: Input/output error
nfs-common: Input/output error
mountnfs.sh: Input/output error
mountnfs-bootclean.sh: Input/output error
bootmisc.sh: Input/output error
x11-common: Input/output error
startpar: service(s) returned failure: mountdevsubfs.sh checkroo[ 43.064697][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 43.076591][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 43.088458][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
INIT: Entering runlevel: 2
INIT: cannot execute "/etc/init.d/rc"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "T0" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
[ 43.602935][ T35] scsi 3:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6
[ 43.615633][ T35] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 43.628160][ T40] sd 3:0:0:0: [sdd] 30031250 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 43.642767][ T40] sd 3:0:0:0: [sdd] Write Protect is off
[ 43.649013][ T40] sd 3:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 43.695881][ T40] sdd: sdd1
[ 43.699603][ T40] sd 3:0:0:0: [sdd] Attached SCSI removable disk
[ 48.496458][ T1] EXT4-fs warning: 84 callbacks suppressed
[ 48.496488][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 53.519057][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 58.535856][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 63.552647][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 68.569453][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 73.586279][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 78.603067][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 83.619865][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 88.636653][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
[ 93.653501][ T1] EXT4-fs warning (device sdc1): dx_probe:823: inode #2: lblock 0: comm init: error -5 reading directory block
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 24, 2025 01:02PM |
Registered: 9 years ago Posts: 63 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700)
ZyXEL NSA310S/320S 1/2-Bay Power Media Server
SoC: Kirkwood 88F6702_A1
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot: 0
NSA3x0S> run poke; ide reset; boot
Reset IDE: Bus 0: OK Bus 1: .........OK
Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6FC8VSV
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6JN55AL
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 3905536 06b4319f-01 83
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 661 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
6223944 bytes read in 1057 ms (5.6 MiB/s)
loading uInitrd ...
5791271 bytes read in 946 ms (5.8 MiB/s)
loading DTB /boot/dts/kirkwood-nsa320s.dtb ...
13335 bytes read in 1799 ms (6.8 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:22 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6223880 Bytes = 5.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:55 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5791207 Bytes = 5.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02c00000
Booting using the fdt blob at 0x2c00000
Loading Kernel Image ... OK
Loading Ramdisk to 0f585000, end 0fb0ade7 ... OK
Loading Device Tree to 0f57e000, end 0f584416 ... OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
[ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 232336K/262144K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 29808K reserved, 0K cma-reserved)
[ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000002][ T0] sched_clock: 32 bits at 167MHz, resolution 6ns, wraps every 12884901885ns
[ 0.000056][ T0] Switching to timer-based delay loop, resolution 6ns
[ 0.000736][ T0] Console: colour dummy device 80x30
[ 0.000819][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.000853][ T0] CPU: Testing write buffer coherency: ok
[ 0.001006][ T0] pid_max: default: 32768 minimum: 301
[ 0.011516][ T0] LSM: initializing lsm=capability,integrity
[ 0.014365][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.014406][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.028926][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.029341][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.029870][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.030340][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.030823][ T1] rcu: Hierarchical SRCU implementation.
[ 0.030842][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.034313][ T1] devtmpfs: initialized
[ 0.047376][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.047427][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.051079][ T1] prandom: seed boundary self test passed
[ 0.056200][ T1] prandom: 100 self tests passed
[ 0.056218][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.060713][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.061671][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.068151][ T1] audit: initializing netlink subsys (disabled)
[ 0.069360][ T19] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1
[ 0.071336][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.071513][ T1] cpuidle: using governor ladder
[ 0.071605][ T1] cpuidle: using governor menu
[ 0.072358][ T1] Feroceon L2: Enabling L2
[ 0.072399][ T1] Feroceon L2: Cache support initialised.
[ 0.086858][ T1] No ATAGs?
[ 0.450074][ T1] raid6: int32x8 gen() 93 MB/s
[ 0.790070][ T1] raid6: int32x4 gen() 92 MB/s
[ 1.130103][ T1] raid6: int32x2 gen() 120 MB/s
[ 1.470070][ T1] raid6: int32x1 gen() 94 MB/s
[ 1.470084][ T1] raid6: using algorithm int32x2 gen() 120 MB/s
[ 1.810072][ T1] raid6: .... xor() 76 MB/s, rmw enabled
[ 1.810085][ T1] raid6: using intx1 recovery algorithm
[ 1.812030][ T1] SCSI subsystem initialized
[ 1.812894][ T1] usbcore: registered new interface driver usbfs
[ 1.812975][ T1] usbcore: registered new interface driver hub
[ 1.813049][ T1] usbcore: registered new device driver usb
[ 1.813521][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.813532][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.813569][ T1] PTP clock support registered
[ 1.816744][ T1] vgaarb: loaded
[ 1.817688][ T1] clocksource: Switched to clocksource orion_clocksource
[ 1.836368][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.836882][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.875111][ T1] NET: Registered PF_INET protocol family
[ 1.875464][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 1.887905][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.888124][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.888158][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 1.888208][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 1.888264][ T1] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.889069][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.889360][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.889397][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.890431][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.891741][ T1] RPC: Registered named UNIX socket transport module.
[ 1.891756][ T1] RPC: Registered udp transport module.
[ 1.891763][ T1] RPC: Registered tcp transport module.
[ 1.891770][ T1] RPC: Registered tcp-with-tls transport module.
[ 1.891777][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.891800][ T1] PCI: CLS 0 bytes, default 32
[ 1.895146][ T32] Trying to unpack rootfs image as initramfs...
[ 3.020537][ T32] Freeing initrd memory: 5656K
[ 4.244107][ T1] Initialise system trusted keyrings
[ 4.244231][ T1] Key type blacklist registered
[ 4.245795][ T1] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 4.245999][ T1] zbud: loaded
[ 4.268990][ T1] NFS: Registering the id_resolver key type
[ 4.269048][ T1] Key type id_resolver registered
[ 4.269059][ T1] Key type id_legacy registered
[ 4.269288][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 4.269313][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 4.271185][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 4.272149][ T1] fuse: init (API version 7.38)
[ 4.273857][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 4.274253][ T1] orangefs_init: module version upstream loaded
[ 4.274725][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 4.528700][ T1] xor: measuring software checksum speed
[ 4.539362][ T1] arm4regs : 927 MB/sec
[ 4.557064][ T1] 8regs : 556 MB/sec
[ 4.569567][ T1] 32regs : 789 MB/sec
[ 4.569579][ T1] xor: using function: arm4regs (927 MB/sec)
[ 4.569596][ T1] async_tx: api initialized (async)
[ 4.569614][ T1] Key type asymmetric registered
[ 4.569623][ T1] Asymmetric key parser 'x509' registered
[ 4.628981][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 4.629503][ T1] io scheduler bfq registered
[ 4.856593][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 4.859239][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 4.860800][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 4.862002][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 4.862097][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 4.862151][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.862185][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.863034][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 4.863057][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.863080][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 4.863100][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 4.863117][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 4.863252][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 4.865441][ T1] PCI: bus0: Fast back to back transfers disabled
[ 4.865474][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.865859][ T1] PCI: bus1: Fast back to back transfers enabled
[ 4.865885][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 4.865934][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 4.867191][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 4.930829][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 4.936335][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 5.000840][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 5.006758][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 5.009896][ T1] printk: console [ttyS0] disabled
[ 5.010656][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 10416666) is a 16550A
[ 5.010734][ T1] printk: console [ttyS0] enabled
[ 6.011910][ T1] loop: module loaded
[ 6.016991][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 6.027968][ T1] scsi host0: sata_mv
[ 6.033662][ T1] scsi host1: sata_mv
[ 6.038073][ T1] ata1: SATA max UDMA/133 irq 29
[ 6.042862][ T1] ata2: SATA max UDMA/133 irq 29
[ 6.049262][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
[ 6.056305][ T1] nand: Eon NAND 128MiB 3,3V 8-bit
[ 6.061291][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 6.069590][ T1] Scanning device for bad blocks
[ 6.079558][ T1] Bad eraseblock 100 at 0x000000c80000
[ 6.089963][ T1] Bad eraseblock 200 at 0x000001900000
[ 6.137280][ T1] 9 cmdlinepart partitions found on MTD device orion_nand
[ 6.144246][ T1] Creating 9 MTD partitions on "orion_nand":
[ 6.150089][ T1] 0x000000000000-0x000000100000 : "uboot"
[ 6.156611][ T1] 0x000000100000-0x000000180000 : "stock_uboot_env"
[ 6.163901][ T1] 0x000000180000-0x000000200000 : "key_store"
[ 6.170732][ T1] 0x000000200000-0x000000280000 : "info"
[ 6.177081][ T1] 0x000000280000-0x000000c80000 : "etc"
[ 6.183431][ T1] 0x000000c80000-0x000001680000 : "kernel_1"
[ 6.190187][ T1] 0x000001680000-0x000004640000 : "rootfs1"
[ 6.196991][ T1] 0x000004640000-0x000005040000 : "kernel_2"
[ 6.203784][ T1] 0x000005040000-0x000008000000 : "rootfs2"
[ 6.211694][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 6.220239][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 6.261171][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 6.272229][ T1] mv643xx_eth: Set the PHY to fix link down
[ 6.273342][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51
[ 6.289397][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 6.295661][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 6.304309][ T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000
[ 6.337717][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 6.344919][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 6.353916][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.361863][ T1] usb usb1: Product: EHCI Host Controller
[ 6.367455][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd
[ 6.374785][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 6.381598][ T1] hub 1-0:1.0: USB hub found
[ 6.386094][ T1] hub 1-0:1.0: 1 port detected
[ 6.391939][ T1] usbcore: registered new interface driver usb-storage
[ 6.399405][ T1] mousedev: PS/2 mouse device common for all mice
[ 6.406119][ T1] i2c_dev: i2c /dev entries driver
[ 6.414584][ T1] ht1382 0-0068: registered as rtc0
[ 6.420955][ T1] ht1382 0-0068: setting system clock to 2025-02-24T18:52:51 UTC (1740423171)
[ 6.431328][ T1] device-mapper: uevent: version 1.0.3
[ 6.437326][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 6.447283][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 6.454573][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 6.461893][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 6.469278][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 6.480080][ T1] ledtrig-cpu: registered to indicate activity on CPUs
[ 6.486993][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 6.493341][ T1] drop_monitor: Initializing network drop monitor service
[ 6.502230][ T1] NET: Registered PF_INET6 protocol family
[ 6.510330][ T1] Segment Routing with IPv6
[ 6.514692][ T1] RPL Segment Routing with IPv6
[ 6.519589][ T1] In-situ OAM (IOAM) with IPv6
[ 6.524332][ T1] NET: Registered PF_PACKET protocol family
[ 6.530687][ T1] Key type dns_resolver registered
[ 6.547772][ T53] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 6.565436][ T53] ata1.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 6.573270][ T1] registered taskstats version 1
[ 6.578150][ T53] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 6.585948][ T1] Loading compiled-in X.509 certificates
[ 6.594118][ T53] ata1.00: configured for UDMA/133
[ 6.618725][ T10] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5
[ 6.632730][ T1] Key type .fscrypt registered
[ 6.637347][ T1] Key type fscrypt-provisioning registered
[ 6.644771][ T32] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 6.653976][ T32] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 6.663796][ T32] sd 0:0:0:0: [sda] Write Protect is off
[ 6.672721][ T1] Key type big_key registered
[ 6.677789][ T50] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 6.688032][ T32] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.708180][ T32] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[ 6.758018][ T1] Key type encrypted registered
[ 6.781731][ T32] sda:
[ 6.784655][ T32] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.894078][ T104] "cryptomgr_test" (104) uses obsolete ecb(arc4) skcipher
[ 6.909691][ T50] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32
[ 6.923727][ T50] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 6.941512][ T50] usb 1-1: Product: USB2.0 Hub
[ 6.948120][ T50] hub 1-1:1.0: USB hub found
[ 6.957823][ T50] hub 1-1:1.0: 4 ports detected
[ 7.157747][ T55] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 7.177982][ T55] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 7.185441][ T55] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.210320][ T55] ata2.00: configured for UDMA/133
[ 7.225939][ T18] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5
[ 7.249516][ T32] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 7.267735][ T32] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 7.273733][ T32] sd 1:0:0:0: [sdb] Write Protect is off
[ 7.287735][ T50] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[ 7.295502][ T32] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.317851][ T32] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[ 7.373970][ T32] sdb: sdb1 sdb2 sdb3
[ 7.389232][ T32] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 7.539565][ T50] usb 1-1.1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 2.00
[ 7.557712][ T50] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7.565697][ T50] usb 1-1.1: Product: DataTraveler 2.0
[ 7.587709][ T50] usb 1-1.1: Manufacturer: Kingston
[ 7.592749][ T50] usb 1-1.1: SerialNumber: 0017318974D91FC0693A4974
[ 7.609363][ T50] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 7.628384][ T50] scsi host2: usb-storage 1-1.1:1.0
[ 8.649911][ T32] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 0000 PQ: 0 ANSI: 4
[ 8.671111][ T18] sd 2:0:0:0: [sdc] 30273600 512-byte logical blocks: (15.5 GB/14.4 GiB)
[ 8.689603][ T18] sd 2:0:0:0: [sdc] Write Protect is off
[ 8.707732][ T18] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 8.738082][ T18] sdc: sdc1
[ 8.748034][ T18] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 9.887644][ T18] kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp33
[ 9.896908][ T18] pinctrl core: failed to register map default (0): invalid type given
[ 9.905887][ T1] clk: Disabling unused clocks
[ 9.914053][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 9.938681][ T1] Checked W+X mappings: passed, no W+X pages found
[ 9.945043][ T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.17-1~deb12u1
[ 11.711949][ T150] usbcore: registered new interface driver uas
[ 13.027742][ T121] usb 1-1.1: reset high-speed USB device number 3 using orion-ehci
[ 13.183886][ T121] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=1s
[ 13.193833][ T121] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 00 00 00 28 00 00 10 00
[ 13.201853][ T121] I/O error, dev sdc, sector 40 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext3 (1) -- /dev/sdc1] fsck.ext3 -a -C0 /dev/sdc1
rootfs: clean, 20075/122160 files, 218978/488192 blocks
done.
[ 24.242255][ T180] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem
[ 24.277137][ T180] EXT4-fs (sdc1): mounted filesystem bcf22700-38c8-477c-9969-e26f648c6e27 ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 27.920474][ T357] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 28.469082][ T367] orion_wdt: Initial timeout 25 sec
[ 28.779099][ T121] random: crng init done
[ 28.962885][ T356] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 29.098018][ T356] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 29.212617][ T356] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 29.261742][ T371] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 30.627799][ T121] usb 1-1.1: reset high-speed USB device number 3 using orion-ehci
done.
Activating swap:.
[ 31.880570][ T525] EXT4-fs (sdc1): re-mounted bcf22700-38c8-477c-9969-e26f648c6e27 r/w. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
Initializing random number generator...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/52:3b:20:9c:11:51
Sending on LPF/eth0/52:3b:20:9c:11:51
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
[ 34.965914][ T904] mv643xx_eth: Set the PHY back to auto-negotiation mode
[ 38.140084][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPOFFER of 192.168.0.164 from 192.168.0.149
DHCPREQUEST for 192.168.0.164 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.0.164 from 192.168.0.149
bound to 192.168.0.164 -- renewal in 17843 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1036 (syslogd)
.
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting NTP server: ntpd2025-02-24T10:53:28 ntpd[1077]: INIT: ntpd ntpsec-1.2.2: Starting
2025-02-24T10:53:28 ntpd[1077]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106
.
Starting NTP server: ntpd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1053 (klogd)
.
Starting OpenBSD Secure Shell server: sshd.
[...]
root@debian:~# blkid
/dev/sdb2: UUID="bb48fb53-be41-509c-3017-a5a8c86610be" TYPE="linux_raid_member" PARTUUID="153d97c3-ffe5-460d-8432-08ee4d18bbb7"
/dev/sdb3: UUID="bf696b87-1701-2808-2ac8-102136ff18b6" UUID_SUB="c6f9a9c6-df7e-e283-869d-70cc3d18b407" LABEL="CHBSLNAM11PRD:2" TYPE="li
nux_raid_member" PARTUUID="798a5e17-f6de-45e9-adff-6d4403507148"
/dev/sdb1: UUID="d0ab8eb1-786b-f19e-3017-a5a8c86610be" TYPE="linux_raid_member" PARTUUID="5a74b4c4-f0e6-4c33-bb1d-e2a15a9b70f8"
/dev/sdc1: LABEL="rootfs" UUID="bcf22700-38c8-477c-9969-e26f648c6e27" BLOCK_SIZE="4096" TYPE="ext3" PARTUUID="06b4319f-01"
/dev/sda: PTUUID="3bb291af-4ee2-4ed1-8b98-9175e8bc947c" PTTYPE="gpt"
root@debian:~# [ 73.386325][ T9] usb 1-1.1: USB disconnect, device number 3
[ 73.400726][ T33] device offline error, dev sdc, sector 2521168 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 2
[ 73.411127][ T33] EXT4-fs warning (device sdc1): ext4_end_bio:343: I/O error 17 writing to inode 8322 starting block 315146)
[ 73.422944][ T33] Buffer I/O error on device sdc1, logical block 314890
[ 73.430128][ T33] device offline error, dev sdc, sector 2517128 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 2
[ 73.440522][ T33] EXT4-fs warning (device sdc1): ext4_end_bio:343: I/O error 17 writing to inode 8328 starting block 314641)
[ 73.452238][ T33] Buffer I/O error on device sdc1, logical block 314385
[ 73.459333][ T18] device offline error, dev sdc, sector 2508216 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 2
[ 73.477868][ T18] EXT4-fs warning (device sdc1): ext4_end_bio:343: I/O error 17 writing to inode 8327 starting block 313527)
[ 73.505614][ T18] Buffer I/O error on device sdc1, logical block 313271
[ 73.518037][ T33] device offline error, dev sdc, sector 2048 op 0x1:(WRITE) flags 0x3000 phys_seg 2 prio class 2
[ 73.528653][ T33] Buffer I/O error on dev sdc1, logical block 0, lost async page write
[ 73.536744][ T33] Buffer I/O error on dev sdc1, logical block 1, lost async page write
[ 73.545476][ T33] device offline error, dev sdc, sector 265168 op 0x1:(WRITE) flags 0x3000 phys_seg 2 prio class 2
[ 73.556257][ T33] Buffer I/O error on dev sdc1, logical block 32890, lost async page write
[ 73.564960][ T33] Buffer I/O error on dev sdc1, logical block 32891, lost async page write
[ 73.573735][ T33] device offline error, dev sdc, sector 265256 op 0x1:(WRITE) flags 0x3000 phys_seg 2 prio class 2
[ 73.584503][ T33] Buffer I/O error on dev sdc1, logical block 32901, lost async page write
[ 73.593171][ T33] Buffer I/O error on dev sdc1, logical block 32902, lost async page write
[ 73.601940][ T33] device offline error, dev sdc, sector 265304 op 0x1:(WRITE) flags 0x3000 phys_seg 1 prio class 2
[ 73.612696][ T33] Buffer I/O error on dev sdc1, logical block 32907, lost async page write
[ 73.621464][ T33] device offline error, dev sdc, sector 265320 op 0x1:(WRITE) flags 0x3000 phys_seg 1 prio class 2
[ 73.632221][ T33] Buffer I/O error on dev sdc1, logical block 32909, lost async page write
[ 73.641017][ T33] device offline error, dev sdc, sector 265344 op 0x1:(WRITE) flags 0x3000 phys_seg 1 prio class 2
[ 73.651767][ T33] Buffer I/O error on dev sdc1, logical block 32912, lost async page write
[ 73.660682][ T33] device offline error, dev sdc, sector 265368 op 0x1:(WRITE) flags 0x3000 phys_seg 1 prio class 2
[ 73.671445][ T33] Buffer I/O error on dev sdc1, logical block 32915, lost async page write
[ 73.727383][ T9] EXT4-fs (sdc1): shut down requested (2)
[ 73.734623][ T9] Aborting journal on device sdc1-8.
[ 73.740531][ T9] JBD2: I/O error when updating journal superblock for sdc1-8.
[ 74.077727][ T9] usb 1-1.1: new high-speed USB device number 4 using orion-ehci
[ 74.319566][ T9] usb 1-1.1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 2.00
[ 74.328672][ T9] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 74.336686][ T9] usb 1-1.1: Product: DataTraveler 2.0
[ 74.342455][ T9] usb 1-1.1: Manufacturer: Kingston
[ 74.347498][ T9] usb 1-1.1: SerialNumber: 0017318974D91FC0693A4974
[ 74.365970][ T9] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 74.384069][ T9] scsi host3: usb-storage 1-1.1:1.0
[ 75.449915][ T18] scsi 3:0:0:0: Direct-Access Kingston DataTraveler 2.0 0000 PQ: 0 ANSI: 4
[ 75.469460][ T18] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 75.475756][ T32] sd 3:0:0:0: [sdd] 30273600 512-byte logical blocks: (15.5 GB/14.4 GiB)
[ 75.500134][ T32] sd 3:0:0:0: [sdd] Write Protect is off
[ 75.510190][ T32] sd 3:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 75.539081][ T32] sdd: sdd1
[ 75.545810][ T32] sd 3:0:0:0: [sdd] Attached SCSI removable disk
root@debian:~# ls
[ 234.538228][ T1109] EXT4-fs warning (device sdc1): dx_probe:822: inode #34959: lblock 0: comm bash: error -5 reading directory block
[ 234.550317][ T1109] EXT4-fs warning (device sdc1): dx_probe:822: inode #35232: lblock 0: comm bash: error -5 reading directory block
-bash: ls: command not found
root@debian:~#
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 24, 2025 03:22PM |
Registered: 6 years ago Posts: 260 |
[ 9.898232][ T18] kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp33
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 24, 2025 09:54PM |
Admin Registered: 14 years ago Posts: 19,425 |
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 24, 2025 10:58PM |
Admin Registered: 14 years ago Posts: 19,425 |
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 25, 2025 11:33AM |
Registered: 9 years ago Posts: 63 |
|
Re: Zyxel NSA320S, USB rootfs, cannot boot with SATA HDDs in recent kernels February 26, 2025 10:49PM |
Admin Registered: 14 years ago Posts: 19,425 |