|
Trying to rescue Pogoplug E02 March 01, 2025 11:48PM |
Registered: 25 days ago Posts: 3 |
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.060000] Bad eraseblock 214 at 0x01ac0000 [ 1.100000] Bad eraseblock 841 at 0x06920000 [ 1.110000] Using static partition definition [ 1.120000] Creating 4 MTD partitions on "nand_mtd": [ 1.120000] 0x00000000-0x00100000 : "u-boot" [ 1.130000] 0x00100000-0x00500000 : "uImage" [ 1.130000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.140000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.150000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 1.880000] usbcore: registered new interface driver usblp [ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.890000] Initializing USB Mass Storage driver... [ 1.890000] usbcore: registered new interface driver usb-storage [ 1.900000] USB Mass Storage support registered. [ 1.900000] mice: PS/2 mouse device common for all mice [ 1.910000] i2c /dev entries driver [ 1.910000] Linux telephony interface: v1.00 [ 1.920000] md: linear personality registered for level -1 [ 1.920000] md: raid0 personality registered for level 0 [ 1.930000] md: raid1 personality registered for level 1 [ 2.100000] raid6: int32x1 97 MB/s [ 2.270000] raid6: int32x2 114 MB/s [ 2.440000] raid6: int32x4 122 MB/s [ 2.610000] raid6: int32x8 110 MB/s [ 2.610000] raid6: using algorithm int32x4 (122 MB/s) [ 2.610000] md: raid6 personality registered for level 6 [ 2.620000] md: raid5 personality registered for level 5 [ 2.620000] md: raid4 personality registered for level 4 [ 2.630000] raid5: measuring checksumming speed [ 2.680000] arm4regs : 1084.000 MB/sec [ 2.730000] 8regs : 754.800 MB/sec [ 2.780000] 32regs : 900.000 MB/sec [ 2.780000] raid5: using function: arm4regs (1084.000 MB/sec) [ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.790000] dm_crypt using the OCF package. [ 2.800000] sdhci: Secure Digital Host Controller Interface driver [ 2.800000] sdhci: Copyright(c) Pierre Ossman [ 2.810000] usbcore: registered new interface driver usbhid [ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.820000] TCP cubic registered [ 2.820000] NET: Registered protocol family 1 [ 2.830000] NET: Registered protocol family 17 [ 2.830000] md: Autodetecting RAID arrays. [ 2.840000] md: autorun ... [ 2.840000] md: ... autorun DONE. [ 3.180000] mtd->read(0x1f6ec bytes from 0x120914) returned ECC error [ 4.670000] Empty flash at 0x009ac208 ends at 0x009ac800 [ 9.550000] VFS: Mounted root (jffs2 filesystem) readonly. [ 9.560000] Freeing init memory: 124K [ 10.690000] mtd->read(0x869 bytes from 0x13e000) returned ECC error [ 10.700000] JFFS2 notice: (1) check_node_data: wrong data CRC in data node at 0x0013e000: read 0x44f122a7, calculated 0x374a1942. init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 CE>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes console=console=ttyS0,115200 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/mtdblock2 ro ethmtu=1500 usb0Mode=host nandEcc=1bit ethact=egiga0 bootargs=console=ttyS0,115200 root=/dev/mtdblock2 ro serverip=169.254.254.252 ipaddr=169.254.254.253 ethaddr=00:25:31:00:7A:66 cesvcid=DEMSRUTTYU9X736TQ3DCD8E26N ceboardver=PPV2 bootcmd=nand read.e 0x800000 0x100000 0x200000; setenv bootargs $(console) $(bootargs_root);bootm 0x800000 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no
CE>> bootm 0x800000 0x1100000 ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2025-03-01 6:20:47 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 6234202 Bytes = 5.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-6.5.7-kirkwood-tld-1 Created: 2023-10-31 22:53:55 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5791207 Bytes = 5.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005317f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: CloudEngines Pogoplug E02 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] INITRD: 0x01100000+0x00586000 overlaps in-use memory region [ 0.000000][ T0] - disabling initrd [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 238008K/262144K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 24136K reserved, 0K cma-reserved) [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000001][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000046][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000625][ T0] Console: colour dummy device 80x30 [ 0.000695][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000724][ T0] CPU: Testing write buffer coherency: ok [ 0.000853][ T0] pid_max: default: 32768 minimum: 301 [ 0.009641][ T0] LSM: initializing lsm=capability,integrity [ 0.012095][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.012131][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.024418][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.024770][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.025223][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.025539][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.025952][ T1] rcu: Hierarchical SRCU implementation. [ 0.025967][ T1] rcu: Max phase no-delay instances is 1000. [ 0.028891][ T1] devtmpfs: initialized [ 0.038009][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.038052][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.041004][ T1] prandom: seed boundary self test passed [ 0.045522][ T1] prandom: 100 self tests passed [ 0.045538][ T1] pinctrl core: initialized pinctrl subsystem [ 0.049313][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.050877][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.056251][ T1] audit: initializing netlink subsys (disabled) [ 0.058276][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.058426][ T1] cpuidle: using governor ladder [ 0.058502][ T1] cpuidle: using governor menu [ 0.059128][ T1] Feroceon L2: Enabling L2 [ 0.059165][ T1] Feroceon L2: Cache support initialised. [ 0.068494][ T1] No ATAGs? [ 0.070102][ T19] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1 [ 0.430062][ T1] raid6: int32x8 gen() 108 MB/s [ 0.770064][ T1] raid6: int32x4 gen() 105 MB/s [ 1.110089][ T1] raid6: int32x2 gen() 132 MB/s [ 1.450063][ T1] raid6: int32x1 gen() 98 MB/s [ 1.450075][ T1] raid6: using algorithm int32x2 gen() 132 MB/s [ 1.790061][ T1] raid6: .... xor() 83 MB/s, rmw enabled [ 1.790075][ T1] raid6: using intx1 recovery algorithm [ 1.791760][ T1] SCSI subsystem initialized [ 1.792569][ T1] usbcore: registered new interface driver usbfs [ 1.792643][ T1] usbcore: registered new interface driver hub [ 1.792713][ T1] usbcore: registered new device driver usb [ 1.793159][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.793170][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it > [ 1.793204][ T1] PTP clock support registered [ 1.796020][ T1] vgaarb: loaded [ 1.796899][ T1] clocksource: Switched to clocksource orion_clocksource [ 1.813416][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.813859][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.848650][ T1] NET: Registered PF_INET protocol family [ 1.848972][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.857106][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.857352][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.857385][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 1.857435][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 1.857490][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 1.858202][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.858457][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.858494][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.859391][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.860613][ T1] RPC: Registered named UNIX socket transport module. [ 1.860626][ T1] RPC: Registered udp transport module. [ 1.860633][ T1] RPC: Registered tcp transport module. [ 1.860639][ T1] RPC: Registered tcp-with-tls transport module. [ 1.860645][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.860667][ T1] PCI: CLS 0 bytes, default 32 [ 3.448473][ T1] Initialise system trusted keyrings [ 3.448645][ T1] Key type blacklist registered [ 3.450202][ T1] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 3.450389][ T1] zbud: loaded [ 3.469950][ T1] NFS: Registering the id_resolver key type [ 3.470001][ T1] Key type id_resolver registered [ 3.470012][ T1] Key type id_legacy registered [ 3.470210][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.470233][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 3.471877][ T1] jffs2: version 2.2. (NAND) (SUMMARY) <C2><A9> 2001-2006 Red Hat, Inc. [ 3.472825][ T1] fuse: init (API version 7.38) [ 3.474313][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 3.474667][ T1] orangefs_init: module version upstream loaded [ 3.475081][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 3.687910][ T1] xor: measuring software checksum speed [ 3.696781][ T1] arm4regs : 1112 MB/sec [ 3.711565][ T1] 8regs : 667 MB/sec [ 3.721979][ T1] 32regs : 947 MB/sec [ 3.721990][ T1] xor: using function: arm4regs (1112 MB/sec) [ 3.722006][ T1] async_tx: api initialized (async) [ 3.722023][ T1] Key type asymmetric registered [ 3.722032][ T1] Asymmetric key parser 'x509' registered [ 3.731444][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 3.731891][ T1] io scheduler bfq registered [ 3.922202][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 3.923931][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 3.925341][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 3.927022][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 3.989606][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 3.994654][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 4.059638][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.065028][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 4.067843][ T1] printk: console [ttyS0] disabled [ 4.068546][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 27, base_baud = 12500000) is a 16550A [ 4.068616][ T1] printk: console [ttyS0] enabled [ 4.945551][ T1] loop: module loaded [ 4.950815][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 4.957957][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit [ 4.963131][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 4.971495][ T1] Scanning device for bad blocks [ 4.999240][ T1] Bad eraseblock 214 at 0x000001ac0000 [ 5.071503][ T1] Bad eraseblock 841 at 0x000006920000 [ 5.096317][ T1] 4 cmdlinepart partitions found on MTD device orion_nand [ 5.103343][ T1] Creating 4 MTD partitions on "orion_nand": [ 5.109233][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 5.115770][ T1] 0x000000100000-0x000000500000 : "uImage" [ 5.122362][ T1] 0x000000500000-0x000002500000 : "rootfs" [ 5.129076][ T1] 0x000002500000-0x000008000000 : "data" [ 5.136634][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 5.145254][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 5.162776][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 5.928292][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:00:7a:66 [ 5.938509][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 5.944767][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 5.953474][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 5.986935][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 6.003129][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.011117][ T1] usb usb1: Product: EHCI Host Controller [ 6.016727][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd [ 6.024098][ T1] usb usb1: SerialNumber: f1050000.ehci [ 6.030660][ T1] hub 1-0:1.0: USB hub found [ 6.035189][ T1] hub 1-0:1.0: 1 port detected [ 6.040976][ T1] usbcore: registered new interface driver usb-storage [ 6.048464][ T1] mousedev: PS/2 mouse device common for all mice [ 6.326941][ T49] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 6.528732][ T49] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 6.537709][ T49] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 6.545613][ T49] usb 1-1: Product: USB2.0 Hub [ 6.551434][ T49] hub 1-1:1.0: USB hub found [ 6.556234][ T49] hub 1-1:1.0: 4 ports detected [ 6.876932][ T49] usb 1-1.4: new high-speed USB device number 3 using orion-ehci [ 7.028983][ T49] usb 1-1.4: New USB device found, idVendor=05dc, idProduct=a768, bcdDevice=11.00 [ 7.038132][ T49] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.046211][ T49] usb 1-1.4: Product: USB Flash Drive [ 7.051490][ T49] usb 1-1.4: Manufacturer: Lexar [ 7.056316][ T49] usb 1-1.4: SerialNumber: BS2LWHT0FI80VI6B4NLS [ 7.063605][ T49] usb-storage 1-1.4:1.0: USB Mass Storage device detected [ 7.071531][ T49] scsi host0: usb-storage 1-1.4:1.0 [ 7.126943][ T1] rtc-mv f1010300.rtc: internal RTC not ticking [ 7.133359][ T1] i2c_dev: i2c /dev entries driver [ 7.139551][ T1] device-mapper: uevent: version 1.0.3 [ 7.145519][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 7.155437][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 7.162787][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 7.170173][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 7.177669][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 7.186374][ T1] ledtrig-cpu: registered to indicate activity on CPUs [ 7.193326][ T1] hid: raw HID events driver (C) Jiri Kosina [ 7.199680][ T1] drop_monitor: Initializing network drop monitor service [ 7.208304][ T1] NET: Registered PF_INET6 protocol family [ 7.216275][ T1] Segment Routing with IPv6 [ 7.220762][ T1] RPL Segment Routing with IPv6 [ 7.225595][ T1] In-situ OAM (IOAM) with IPv6 [ 7.230396][ T1] NET: Registered PF_PACKET protocol family [ 7.236601][ T1] Key type dns_resolver registered [ 7.262304][ T1] registered taskstats version 1 [ 7.267565][ T1] Loading compiled-in X.509 certificates [ 7.296407][ T1] Key type .fscrypt registered [ 7.301160][ T1] Key type fscrypt-provisioning registered [ 7.313515][ T1] Key type big_key registered [ 7.324052][ T1] Key type encrypted registered [ 7.397716][ T102] "cryptomgr_test" (102) uses obsolete ecb(arc4) skcipher [ 8.088195][ T10] scsi 0:0:0:0: Direct-Access Lexar USB Flash Drive 1100 PQ: 0 ANSI: 0 CCS [ 8.109147][ T18] sd 0:0:0:0: [sda] 15663104 512-byte logical blocks: (8.02 GB/7.47 GiB) [ 8.127515][ T18] sd 0:0:0:0: [sda] Write Protect is off [ 8.136958][ T18] sd 0:0:0:0: [sda] No Caching mode page found [ 8.143033][ T18] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 8.172140][ T18] sda: sda1 [ 8.187211][ T18] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 9.798767][ T1] clk: Disabling unused clocks [ 9.803737][ T1] Waiting 10 sec before mounting root device... [ 20.327003][ T1] md: Waiting for all devices to be available before autodetect [ 20.334538][ T1] md: If you don't use raid, use raid=noautodetect [ 20.340966][ T1] md: Autodetecting RAID arrays. [ 20.345786][ T1] md: autorun ... [ 20.349313][ T1] md: ... autorun DONE. [ 20.355271][ T1] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.386106][ T1] EXT4-fs (sda1): mounted filesystem 10adbae8-dd41-45c2-b9c8-ad596c881ebc ro with ordered data mode. Quota mode: none. [ 20.398563][ T1] VFS: Mounted root (ext3 filesystem) readonly on device 8:1. [ 20.559332][ T1] devtmpfs: mounted [ 20.566240][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 20.573689][ T1] Checked W+X mappings: passed, no W+X pages found [ 20.580150][ T1] Run /sbin/init as init process ^MINIT: version 3.06 booting ^MINIT: No inittab.d directory found Using makefile-style concurrent boot in runlevel S. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 24.709367][ T283] orion_wdt: Initial timeout 21 sec [ 25.427155][ T285] marvell-cesa f1030000.crypto: CESA device successfully registered [ 25.522657][ T280] usbcore: registered new interface driver uas [ 25.727522][ T280] sd 0:0:0:0: Attached scsi generic sg0 type 0 done. Setting hostname to 'debian'...done. Activating swap:. [ 27.460202][ T451] EXT4-fs (sda1): re-mounted 10adbae8-dd41-45c2-b9c8-ad596c881ebc ro. Quota mode: none. Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.47.0 (5-Feb-2023) rootfs: clean, 20039/489600 files, 237292/1957632 blocks . [ 27.675133][ T458] EXT4-fs (sda1): re-mounted 10adbae8-dd41-45c2-b9c8-ad596c881ebc r/w. Quota mode: none. Will now check all file systems. [ 29.144592][ T55] random: crng init done Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. Initializing random number generator...done. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1 Copyright 2004-2022 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:00:7a:66 Sending on LPF/eth0/00:25:31:00:7a:66 Sending on Socket/fallback DHCPREQUEST for 192.168.0.17 on eth0 to 255.255.255.255 port 67 [ 45.012858][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... ^MINIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Not starting NFS kernel daemon: no exports ... ESC[33m(warning).ESC[0m Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 968 (syslogd) . Starting NTP server: ntpd1969-12-31T16:00:54 ntpd[988]: INIT: ntpd ntpsec-1.2.2: Starting 1969-12-31T16:00:54 ntpd[988]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106 . Starting system message bus: dbus. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting NTP server: ntpd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 991 (klogd) . Starting OpenBSD Secure Shell server: sshdsshd: no hostkeys available -- exiting. ESC[31mfailed!ESC[0m Running local boot scripts (/etc/rc.local) ^@ssh-keygen: generating new host keys: RSA ^@ECDSA ^@ED25519 ^@ Starting OpenBSD Secure Shell server: sshd ^@. . Debian GNU/Linux 12 debian ttyS0 debian login: root Password: Linux debian 6.5.7-kirkwood-tld-1 #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023 armv5tel SC[?2004hroot@debian:~# cat /etc/fw_env.config ESC[?2004l^M# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 ESC[?2004hroot@debian:~# cat /proc/mtd ESC[?2004l^Mdev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00400000 00020000 "uImage" mtd2: 02000000 00020000 "rootfs" mtd3: 05b00000 00020000 "data" ESC[?2004hroot@debian:~# dmesg | grep -i bad ESC[?2004l^M[ 4.971495] Scanning device for bad blocks [ 4.999240] Bad eraseblock 214 at 0x000001ac0000 [ 5.071503] Bad eraseblock 841 at 0x000006920000 ESC[?2004hroot@debian:~# fw_printenv ethaddr ESC[?2004l^M[17033.800052][ T1141] ecc_sw_hamming_correct: uncorrectable ECC error [17033.806519][ T1141] ecc_sw_hamming_correct: uncorrectable ECC error [17033.812829][ T1141] ecc_sw_hamming_correct: uncorrectable ECC error [17033.819725][ T1141] ecc_sw_hamming_correct: uncorrectable ECC error 8< snip 8< [17036.724297][ T1141] ecc_sw_hamming_correct: uncorrectable ECC error Cannot read environment, using default Cannot read default environment from file
|
Re: Trying to rescue Pogoplug E02 March 02, 2025 04:05AM |
Admin Registered: 14 years ago Posts: 19,425 |
[ 0.000000][ T0] INITRD: 0x01100000+0x00586000 overlaps in-use memory region [ 0.000000][ T0] - disabling initrd
Quote
Kirkwood plugs
Boot Kirkwood rootfs with stock u-boot
[ 4.999240] Bad eraseblock 214 at 0x000001ac0000 [ 5.071503] Bad eraseblock 841 at 0x000006920000
|
Re: Trying to rescue Pogoplug E02 March 02, 2025 02:05PM |
Registered: 25 days ago Posts: 3 |
CE>> printenv^M baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ run_diag=yes console=console=ttyS0,115200 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/mtdblock2 ro ethmtu=1500 usb0Mode=host nandEcc=1bit ethact=egiga0 ethaddr=00:25:31:00:7A:66 cesvcid=DEMSRUTTYU9X736TQ3DCD8E26N ceboardver=PPV2 bootcmd=nand read.e 0x800000 0x100000 0x200000; setenv bootargs $(console) $(bootargs_root);bootm 0x800000 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no exMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial filesize=585e27 fileaddr=2100000 netmask=255.255.0.0 ipaddr=192.168.8.77 serverip=192.168.8.174 Environment size: 841/131068 bytes CE>> bootm 0x800000 0x2100000^M ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2025-03-01 6:20:47 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 6234202 Bytes = 5.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-6.5.7-kirkwood-tld-1 Created: 2023-10-31 22:53:55 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5791207 Bytes = 5.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005317f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: CloudEngines Pogoplug E02 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232352K/262144K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 29792K reserved, 0K cma-reserved) [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008531][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015701][ T0] Console: colour dummy device 80x30 [ 0.020933][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032165][ T0] CPU: Testing write buffer coherency: ok [ 0.037854][ T0] pid_max: default: 32768 minimum: 301 [ 0.052010][ T0] LSM: initializing lsm=capability,integrity [ 0.060282][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.068286][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.089039][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.097114][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.105841][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.113087][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.119347][ T1] rcu: Hierarchical SRCU implementation. [ 0.124834][ T1] rcu: Max phase no-delay instances is 1000. [ 0.133703][ T1] devtmpfs: initialized [ 0.146797][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.157463][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.167814][ T1] prandom: seed boundary self test passed [ 0.177931][ T1] prandom: 100 self tests passed [ 0.182756][ T1] pinctrl core: initialized pinctrl subsystem [ 0.192466][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.200647][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.213662][ T1] audit: initializing netlink subsys (disabled) [ 0.221803][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.221957][ T1] cpuidle: using governor ladder [ 0.233483][ T19] audit: type=2000 audit(0.210:1): state=initialized audit_enabled=0 res=1 [ 0.242039][ T1] cpuidle: using governor menu [ 0.247270][ T1] Feroceon L2: Enabling L2 [ 0.251611][ T1] Feroceon L2: Cache support initialised. [ 0.266477][ T1] No ATAGs? [ 0.628547][ T1] raid6: int32x8 gen() 108 MB/s [ 0.968549][ T1] raid6: int32x4 gen() 105 MB/s [ 1.308576][ T1] raid6: int32x2 gen() 136 MB/s [ 1.648548][ T1] raid6: int32x1 gen() 98 MB/s [ 1.653498][ T1] raid6: using algorithm int32x2 gen() 136 MB/s [ 2.008549][ T1] raid6: .... xor() 84 MB/s, rmw enabled [ 2.014028][ T1] raid6: using intx1 recovery algorithm [ 2.030235][ T1] SCSI subsystem initialized [ 2.039158][ T1] usbcore: registered new interface driver usbfs [ 2.045387][ T1] usbcore: registered new interface driver hub [ 2.068622][ T1] usbcore: registered new device driver usb [ 2.074794][ T1] pps_core: LinuxPPS API ver. 1 registered [ 2.088750][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 2.108644][ T1] PTP clock support registered [ 2.128605][ T1] vgaarb: loaded [ 2.132929][ T1] clocksource: Switched to clocksource orion_clocksource [ 2.162272][ T1] VFS: Disk quotas dquot_6.6.0 [ 2.173388][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.219372][ T1] NET: Registered PF_INET protocol family [ 2.233272][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 2.254202][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 2.273184][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 2.281624][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 2.312988][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 2.320842][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 2.343671][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 2.351798][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 2.372977][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 2.381509][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 2.404069][ T1] RPC: Registered named UNIX socket transport module. [ 2.410665][ T1] RPC: Registered udp transport module. [ 2.422955][ T1] RPC: Registered tcp transport module. [ 2.428341][ T1] RPC: Registered tcp-with-tls transport module. [ 2.452948][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.460074][ T1] PCI: CLS 0 bytes, default 32 [ 2.475968][ T10] Trying to unpack rootfs image as initramfs... [ 3.477030][ T10] Freeing initrd memory: 5656K [ 4.363803][ T1] Initialise system trusted keyrings [ 4.369050][ T1] Key type blacklist registered [ 4.375352][ T1] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 4.382651][ T1] zbud: loaded [ 4.405428][ T1] NFS: Registering the id_resolver key type [ 4.411200][ T1] Key type id_resolver registered [ 4.416115][ T1] Key type id_legacy registered [ 4.421001][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 4.428410][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 4.438134][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 4.446826][ T1] fuse: init (API version 7.38) [ 4.453024][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 4.460481][ T1] orangefs_init: module version upstream loaded [ 4.466993][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 4.688955][ T1] xor: measuring software checksum speed [ 4.703429][ T1] arm4regs : 1100 MB/sec [ 4.723238][ T1] 8regs : 667 MB/sec [ 4.738677][ T1] 32regs : 947 MB/sec [ 4.743734][ T1] xor: using function: arm4regs (1100 MB/sec) [ 4.749641][ T1] async_tx: api initialized (async) [ 4.754702][ T1] Key type asymmetric registered [ 4.759476][ T1] Asymmetric key parser 'x509' registered [ 4.817980][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 4.826627][ T1] io scheduler bfq registered [ 5.021526][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 5.031331][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 5.042288][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 5.053615][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 5.125648][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 5.138655][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 5.205659][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 5.219017][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.228844][ T1] printk: console [ttyS0] disabled [ 5.234586][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 27, base_baud = 12500000) is a 16550A [ 5.244335][ T1] printk: console [ttyS0] enabled [ 5.244335][ T1] printk: console [ttyS0] enabled [ 5.254173][ T1] printk: bootconsole [earlycon0] disabled [ 5.254173][ T1] printk: bootconsole [earlycon0] disabled [ 5.297266][ T1] loop: module loaded [ 5.302452][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 5.309602][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit [ 5.314795][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 5.323164][ T1] Scanning device for bad blocks [ 5.350908][ T1] Bad eraseblock 214 at 0x000001ac0000 [ 5.423177][ T1] Bad eraseblock 841 at 0x000006920000 [ 5.448032][ T1] 4 fixed-partitions partitions found on MTD device orion_nand [ 5.455501][ T1] Creating 4 MTD partitions on "orion_nand": [ 5.461371][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 5.467932][ T1] 0x000000100000-0x000000600000 : "uImage" [ 5.474539][ T1] 0x000000500000-0x000002a00000 : "pogoplug" [ 5.481375][ T1] 0x000002500000-0x000009100000 : "root" [ 5.486933][ T1] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0x5b00000 [ 5.499757][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 5.508370][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 5.546071][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.314407][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:00:7a:66 [ 6.324672][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 6.330932][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 6.339624][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 6.372964][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 6.380060][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05 [ 6.389111][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.397099][ T1] usb usb1: Product: EHCI Host Controller [ 6.402709][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd [ 6.410081][ T1] usb usb1: SerialNumber: f1050000.ehci [ 6.416657][ T1] hub 1-0:1.0: USB hub found [ 6.421181][ T1] hub 1-0:1.0: 1 port detected [ 6.426978][ T1] usbcore: registered new interface driver usb-storage [ 6.434488][ T1] mousedev: PS/2 mouse device common for all mice [ 6.712970][ T49] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 6.914758][ T49] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 6.923728][ T49] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 6.931630][ T49] usb 1-1: Product: USB2.0 Hub [ 6.937590][ T49] hub 1-1:1.0: USB hub found [ 6.942380][ T49] hub 1-1:1.0: 4 ports detected [ 7.262962][ T49] usb 1-1.4: new high-speed USB device number 3 using orion-ehci [ 7.415508][ T49] usb 1-1.4: New USB device found, idVendor=05dc, idProduct=a768, bcdDevice=11.00 [ 7.424654][ T49] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.432734][ T49] usb 1-1.4: Product: USB Flash Drive [ 7.438015][ T49] usb 1-1.4: Manufacturer: Lexar [ 7.442840][ T49] usb 1-1.4: SerialNumber: BS2LWHT0FI80VI6B4NLS [ 7.450173][ T49] usb-storage 1-1.4:1.0: USB Mass Storage device detected [ 7.457263][ T1] rtc-mv f1010300.rtc: internal RTC not ticking [ 7.464473][ T1] i2c_dev: i2c /dev entries driver [ 7.470250][ T49] scsi host0: usb-storage 1-1.4:1.0 [ 7.477482][ T1] device-mapper: uevent: version 1.0.3 [ 7.483495][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 7.493418][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 7.500691][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 7.508115][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 7.515628][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 7.524384][ T1] ledtrig-cpu: registered to indicate activity on CPUs [ 7.531289][ T1] hid: raw HID events driver (C) Jiri Kosina [ 7.537638][ T1] drop_monitor: Initializing network drop monitor service [ 7.546291][ T1] NET: Registered PF_INET6 protocol family [ 7.554284][ T1] Segment Routing with IPv6 [ 7.558676][ T1] RPL Segment Routing with IPv6 [ 7.563589][ T1] In-situ OAM (IOAM) with IPv6 [ 7.568362][ T1] NET: Registered PF_PACKET protocol family [ 7.574558][ T1] Key type dns_resolver registered [ 7.600196][ T1] registered taskstats version 1 [ 7.605440][ T1] Loading compiled-in X.509 certificates [ 7.634426][ T1] Key type .fscrypt registered [ 7.639095][ T1] Key type fscrypt-provisioning registered [ 7.651685][ T1] Key type big_key registered [ 7.702764][ T1] Key type encrypted registered [ 7.818659][ T102] "cryptomgr_test" (102) uses obsolete ecb(arc4) skcipher [ 8.494347][ T29] scsi 0:0:0:0: Direct-Access Lexar USB Flash Drive 1100 PQ: 0 ANSI: 0 CCS [ 8.515176][ T18] sd 0:0:0:0: [sda] 15663104 512-byte logical blocks: (8.02 GB/7.47 GiB) [ 8.533542][ T18] sd 0:0:0:0: [sda] Write Protect is off [ 8.542987][ T18] sd 0:0:0:0: [sda] No Caching mode page found [ 8.549054][ T18] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 8.578540][ T18] sda: sda1 [ 8.593247][ T18] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 10.219858][ T1] clk: Disabling unused clocks [ 10.227878][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 10.243767][ T1] Checked W+X mappings: passed, no W+X pages found [ 10.250179][ T1] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.17-1~deb12u1 [ 11.652626][ T150] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.38.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: clean, 20055/489600 files, 237619/1957632 blocks done. [ 22.464193][ T172] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 22.531529][ T172] EXT4-fs (sda1): mounted filesystem 10adbae8-dd41-45c2-b9c8-ad596c881ebc ro with ordered data mode. Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. ^MINIT: version 3.06 booting^M ^MINIT: No inittab.d directory found^M Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 26.213390][ T349] orion_wdt: Initial timeout 21 sec [ 26.946134][ T365] marvell-cesa f1030000.crypto: CESA device successfully registered [ 27.012530][ T355] sd 0:0:0:0: Attached scsi generic sg0 type 0 done. Activating swap:. [ 28.681097][ T506] EXT4-fs (sda1): re-mounted 10adbae8-dd41-45c2-b9c8-ad596c881ebc r/w. Quota mode: none. [ 29.693761][ T55] random: crng init done Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. Initializing random number generator...done. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1 Copyright 2004-2022 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:00:7a:66 Sending on LPF/eth0/00:25:31:00:7a:66 Sending on Socket/fallback DHCPREQUEST for 192.168.8.176 on eth0 to 255.255.255.255 port 67 [ 45.813318][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled DHCPREQUEST for 192.168.8.176 on eth0 to 255.255.255.255 port 67 DHCPREQUEST for 192.168.8.176 on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPOFFER of 192.168.8.176 from 192.168.8.1 DHCPREQUEST for 192.168.8.176 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.8.176 from 192.168.8.1 bound to 192.168.8.176 -- renewal in 37964 seconds. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... ^MINIT: Entering runlevel: 2^M Using makefile-style concurrent boot in runlevel 2. Not starting NFS kernel daemon: no exports ... ^[[33m(warning).^[[0m Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1019 (syslogd) . Starting system message bus: dbus. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting NTP server: ntpd1969-12-31T16:00:56 ntpd[1058]: INIT: ntpd ntpsec-1.2.2: Starting 1969-12-31T16:00:56 ntpd[1058]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106 . Starting NTP server: ntpd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1034 (klogd) . Starting OpenBSD Secure Shell server: sshd. Running local boot scripts (/etc/rc.local) ^@. ^M Debian GNU/Linux 12 debian ttyS0 debian login:
^[[?2004hroot@debian:~# fw_printenv > current_envs.txt ^[[?2004l^M[ 282.238516][ T1105] ecc_sw_hamming_correct: uncorrectable ECC error [ 282.244957][ T1105] ecc_sw_hamming_correct: uncorrectable ECC error [ 282.251268][ T1105] ecc_sw_hamming_correct: uncorrectable ECC error 8< snip 8< [ 285.156632][ T1105] ecc_sw_hamming_correct: uncorrectable ECC error [ 285.163150][ T1105] ecc_sw_hamming_correct: uncorrectable ECC error Cannot read environment, using default Cannot read default environment from file
cat /etc/fw_env.config ^[[?2004l^M# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 ^[[?2004hroot@debian:~# cat /r^H ^Hproc/mtd ^[[?2004l^Mdev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00500000 00020000 "uImage" mtd2: 02500000 00020000 "pogoplug" mtd3: 05b00000 00020000 "root"
root@debian:~# nanddump --noecc --omitoob -l 0x80000 -f mtd0 /dev/mtd0 ^[[?2004l^MBlock size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... root@debian:/tmp# flash_erase /dev/mtd0 0 4 Erasing 128 Kibyte @ 60000 -- 100 % complete root@debian:/tmp# nandwrite /dev/mtd0 uboot.2017.07-tld-1.pogo_e02.mtd0.kwb Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000
|
Re: Trying to rescue Pogoplug E02 March 02, 2025 10:19PM |
Admin Registered: 14 years ago Posts: 19,425 |
> root@debian:~# nanddump --noecc --omitoob -l > 0x80000 -f mtd0 /dev/mtd0 > ^[[?2004l^MBlock size 131072, page size 2048, OOB > size 64 > Dumping data starting at 0x00000000 and ending at > 0x00080000... > > root@debian:/tmp# flash_erase /dev/mtd0 0 4 > Erasing 128 Kibyte @ 60000 -- 100 % complete > root@debian:/tmp# nandwrite /dev/mtd0 > uboot.2017.07-tld-1.pogo_e02.mtd0.kwb > Writing data to block 0 at offset 0x0 > Writing data to block 1 at offset 0x20000 > >>
Quote
If you don't have /etc/fw_env.config file in your system then go ahead and create this file with the above content. MTD parts are not important for booting and it can be adjusted later. For users who like to keep the stock mtd definition, there is no need to adjust it to the above definition. As long as mtd0 is defined as 1MB (0x00100000) or greater then it will be OK:
mtd0: 00100000 00020000 "u-boot"
mtd0: 00100000 00020000 "u-boot"Then go ahead and continue with 8.d.
|
Re: Trying to rescue Pogoplug E02 March 02, 2025 11:22PM |
Registered: 25 days ago Posts: 3 |
|
Re: Trying to rescue Pogoplug E02 March 03, 2025 02:58AM |
Admin Registered: 14 years ago Posts: 19,425 |