[GoFlex Net] SATA November 21, 2013 12:04AM |
Registered: 13 years ago Posts: 4 |
Re: [GoFlex Net] SATA November 21, 2013 01:08AM |
Admin Registered: 13 years ago Posts: 18,821 |
cat /proc/cpuinfo fw_printenv
Re: [GoFlex Net] SATA November 21, 2013 04:39PM |
Registered: 13 years ago Posts: 4 |
Linux debian 3.3.2-kirkwood-dg #1 Mon Apr 23 17:09:27 CDT 2012 armv5tel root@debian:~# cat /proc/cpuinfo Processor : Feroceon 88FR131 rev 1 (v5l) BogoMIPS : 1191.11 Features : swp half thumb fastmult edsp CPU implementer : 0x56 CPU architecture: 5TE CPU variant : 0x2 CPU part : 0x131 CPU revision : 1 Hardware : Marvell SheevaPlug Reference Board Revision : 0000 Serial : 0000000000000000 root@debian:~# fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ethaddr=00:10:75:26:49:BE arcNumber=2097
Re: [GoFlex Net] SATA November 21, 2013 11:00PM |
Admin Registered: 13 years ago Posts: 18,821 |
robert
Re: [GoFlex Net] SATA January 09, 2014 01:06AM |
Re: [GoFlex Net] SATA January 09, 2014 01:43AM |
Admin Registered: 13 years ago Posts: 18,821 |
robert
Re: [GoFlex Net] SATA January 09, 2014 05:19AM |
robert
GoFlex Net SATA boot January 09, 2014 08:30AM |
b@big2:~$ nc.traditional -l -u -p 6666 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1751 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1730 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD800BEAS-00RRT0 Firm: 04.01G04 Ser#: WD-WXE208C02426 Type: Hard Disk Supports 48-bit addressing Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) Loading file "/boot/uImage" from ide device 0:1 (hda1) 2319128 bytes read Loading file "/boot/uInitrd" from ide device 0:1 (hda1) 6544748 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.12.0-kirkwood-tld-3 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2319064 Bytes = 2.2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.12.0-kirkwood-tld-3 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6544684 Bytes = 6.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...
robert
Re: [GoFlex Net] SATA January 09, 2014 08:55AM |
Re: GoFlex Net SATA boot January 09, 2014 08:59AM |
Admin Registered: 13 years ago Posts: 18,821 |
fw_printenvand post here.
robert
Re: GoFlex Net SATA boot January 09, 2014 11:16AM |
robert
Re: [GoFlex Net] SATA January 09, 2014 12:38PM |
robert
SATA boot - Solved January 09, 2014 02:17PM |
Re: SATA boot - Solved January 09, 2014 10:10PM |
Admin Registered: 13 years ago Posts: 18,821 |
robert
Re: SATA boot - Solved January 11, 2014 08:50AM |