pogoplug-E02 broken how to fix to boot then install debian

Been trying to get debian to boot on a pogoplug E02.

Right now I have no network ip show up and have a usb serial cable ... below is a dump of output from serial output on power up ... what are the next steps to get this device to a point I can install debian on it and access it without a serial cable?



U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 727
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 716
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ....... read_nand_cached: error reading nand off 0x10e0000 size s
. read_nand_cached: error reading nand off 0x1c00000 size 8192 bytes
done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...


U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 0Mhz L2 running @ 0Mhz
SysClock = 0Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x200000

Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-08-10 19:57:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1977716 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux..................................................................
[ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #44 M9
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 252K data, 120K init)
[ 0.270000] Mount-cache hash table entries: 512
[ 0.270000] CPU: Testing write buffer coherency: ok
[ 0.270000] NET: Registered protocol family 16
[ 0.270000]
[ 0.270000] CPU Interface
[ 0.270000] -------------
[ 0.270000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.270000] SDRAM_CS1 ....disable
[ 0.270000] SDRAM_CS2 ....disable
[ 0.270000] SDRAM_CS3 ....disable
[ 0.270000] PEX0_MEM ....base e8000000, size 128MB
[ 0.270000] PEX0_IO ....base f2000000, size 1MB
[ 0.270000] INTER_REGS ....base f1000000, size 1MB
[ 0.270000] NFLASH_CS ....base fa000000, size 2MB
[ 0.270000] SPI_CS ....base f4000000, size 16MB
[ 0.270000] BOOT_ROM_CS ....no such
[ 0.270000] DEV_BOOTCS ....no such
[ 0.270000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.270000]
[ 0.270000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21)-- SHEEE
[ 0.270000]
[ 0.270000] Detected Tclk 200000000 and SysClk 0
[ 0.270000] MV Buttons Device Load
[ 0.270000] Marvell USB EHCI Host controller #0: c0650600
[ 0.770000] PEX0 interface detected no Link.
[ 0.770000] PCI: bus0: Fast back to back transfers enabled
[ 0.770000] SCSI subsystem initialized
[ 0.770000] usbcore: registered new interface driver usbfs
[ 0.770000] usbcore: registered new interface driver hub
[ 0.770000] usbcore: registered new device driver usb
[ 0.770000] NET: Registered protocol family 2
[ 0.780000] Time: kw_clocksource clocksource has been installed.
[ 0.870000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.870000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.870000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.870000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.870000] TCP reno registered
[ 0.900000] RTC has been updated!!!
[ 0.900000] RTC registered
[ 0.900000] Use the XOR engines (acceleration) for enhancing the following functi:
[ 0.900000] o RAID 5 Xor calculation
[ 0.900000] o kernel memcpy
[ 0.900000] o kenrel memzero
[ 0.900000] Number of XOR engines to use: 4
[ 0.900000] cesadev_init(c00116b4)
[ 0.900000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.900000] MV Buttons Driver Load
[ 0.900000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.900000] squashfs: LZMA suppport for slax.org by jro
[ 0.900000] JFFS2 version 2.2. (NAND) �Â�© 2001-2006 Red Hat, Inc.
[ 0.910000] io scheduler noop registered
[ 0.910000] io scheduler anticipatory registered (default)
[ 0.920000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disad
[ 0.920000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.930000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 0.940000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.940000] Loading Marvell Ethernet Driver:
[ 0.950000] o Cached descriptors in DRAM
[ 0.950000] o DRAM SW cache-coherency
[ 0.960000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.960000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.970000] o TCP segmentation offload enabled
[ 0.970000] o Receive checksum offload enabled
[ 0.980000] o Transmit checksum offload enabled
[ 0.980000] o Network Fast Processing (Routing) supported
[ 0.990000] o Driver ERROR statistics enabled
[ 0.990000] o Driver INFO statistics enabled
[ 1.000000] o Proc tool API enabled
[ 1.000000] o Rx descripors: q0=128
[ 1.000000] o Tx descripors: q0=532
[ 1.010000] o Loading network interface(s):
[ 1.010000] o eth0, ifindex = 1, GbE port = 0
[ 1.020000] o eth1, ifindex = 2, GbE port = 1
[ 1.020000]
[ 1.030000] mvFpRuleDb (cf8be000): 2048 entries, 8192 bytes
[ 1.030000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.040000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.040000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.050000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.060000]
[ 1.060000] Warning Sata is Powered Off
[ 1.060000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.4$
[ 1.070000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128Mi)
[ 1.080000] Scanning device for bad blocks
[ 1.090000] Bad eraseblock 135 at 0x010e0000
[ 1.100000] Bad eraseblock 224 at 0x01c00000
[ 1.110000] Bad eraseblock 421 at 0x034a0000
[ 1.140000] Using static partition definition
[ 1.150000] Creating 4 MTD partitions on "nand_mtd":
[ 1.150000] 0x00000000-0x00100000 : "u-boot"
[ 1.160000] 0x00100000-0x00500000 : "uImage"
[ 1.160000] 0x00500000-0x02500000 : "root"
[ 1.170000] 0x02500000-0x08000000 : "data"
[ 1.170000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.180000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus1
[ 1.220000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.240000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 14
[ 1.240000] usb usb1: configuration #1 chosen from 1 choice
[ 1.250000] hub 1-0:1.0: USB hub found
[ 1.250000] hub 1-0:1.0: 1 port detected
[ 1.370000] USB Universal Host Controller Interface driver v3.0
[ 1.650000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.800000] usb 1-1: configuration #1 chosen from 1 choice
[ 1.800000] hub 1-1:1.0: USB hub found
[ 1.810000] hub 1-1:1.0: 4 ports detected
[ 1.920000] usbcore: registered new interface driver usblp
[ 1.920000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 1.930000] Initializing USB Mass Storage driver...
[ 1.930000] usbcore: registered new interface driver usb-storage
[ 1.940000] USB Mass Storage support registered.
[ 1.950000] mice: PS/2 mouse device common for all mice
[ 1.950000] i2c /dev entries driver
[ 1.950000] Linux telephony interface: v1.00
[ 1.960000] md: linear personality registered for level -1
[ 1.960000] md: raid0 personality registered for level 0
[ 1.970000] md: raid1 personality registered for level 1
[ 2.140000] raid6: int32x1 86 MB/s
[ 2.310000] raid6: int32x2 101 MB/s
[ 2.480000] raid6: int32x4 108 MB/s
[ 2.650000] raid6: int32x8 98 MB/s
[ 2.650000] raid6: using algorithm int32x4 (108 MB/s)
[ 2.650000] md: raid6 personality registered for level 6
[ 2.660000] md: raid5 personality registered for level 5
[ 2.670000] md: raid4 personality registered for level 4
[ 2.670000] raid5: measuring checksumming speed
[ 2.720000] arm4regs : 963.600 MB/sec
[ 2.770000] 8regs : 670.800 MB/sec
[ 2.820000] 32regs : 791.600 MB/sec
[ 2.820000] raid5: using function: arm4regs (963.600 MB/sec)
[ 2.830000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-develm
[ 2.830000] dm_crypt using the OCF package.
[ 2.840000] sdhci: Secure Digital Host Controller Interface driver
[ 2.840000] sdhci: Copyright(c) Pierre Ossman
[ 2.850000] usbcore: registered new interface driver usbhid
[ 2.850000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 2.860000] TCP cubic registered
[ 2.860000] NET: Registered protocol family 1
[ 2.870000] NET: Registered protocol family 17
[ 2.870000] md: Autodetecting RAID arrays.
[ 2.880000] md: autorun ...
[ 2.880000] md: ... autorun DONE.
[ 6.140000] Empty flash at 0x009ac208 ends at 0x009ac800
[ 6.340000] Empty flash at 0x014d02ec ends at 0x014d0800
[ 7.040000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 7.050000] Freeing init memory: 120K
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 269, tty '': '/etc/init.d/rcS'
[ 9.240000] eth0: link down
[ 9.240000] eth0: started
udhcpc (v1.7.0) started
HWADDR 00 0x25 0x31 0x02 0x1f 0x60
PIP0 31
PIP1 96
Sending discover...
Sending discover...
[ 12.170000] eth0: link up, full duplex, speed 1 Gbps
Sending discover...
Sending select for 192.168.1.43...
Lease of 192.168.1.43 obtained, lease time 86400
HWADDR 00 0x25 0x31 0x02 0x1f 0x60
PIP0 31
PIP1 96
eth0 Link encap:Ethernet HWaddr 00:25:31:02:1F:60
inet addr:192.168.1.43 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:754 (754.0 B) TX bytes:1180 (1.1 KiB)
Interrupt:11

eth0:0 Link encap:Ethernet HWaddr 00:25:31:02:1F:60
inet addr:169.254.31.96 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:11

starting pid 321, tty '': '/bin/sh'
-sh-3.2#

Use this latest rootfs, put it on a USB thumb drive and boot with it:
http://forum.doozan.com/read.php?2,12096

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

i put rootfs on usb thumbdrive you referred to above and rebooted WITHOUT serial cable attached ... the pogo does NOT show up on the network.

If I reboot and attach the serial cable (usb) an ip address for the pogo does show up but I can not run the device like this ... need to boot without serial cable attached .... this is the output i see from the serial output ... what causes the -19 error ?

UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!

dump from serial captured serial output:

U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 727
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 716
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
2319128 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
6544748 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.12.0-kirkwood-tld-3
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2319064 Bytes = 2.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-3.12.0-kirkwood-tld-3
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6544684 Bytes = 6.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.12.0-kirkwood-tld-3 (root@tldDebian) (gcc version 4.63
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Marvell SheevaPlug Reference Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 4
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246520K/262144K available (4398K kernel code, 333K rwdata, 15)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc05d4ce0 (5940 kB)
[ 0.000000] .init : 0xc05d5000 - 0xc0608ac4 ( 207 kB)
[ 0.000000] .data : 0xc060a000 - 0xc065d574 ( 334 kB)
[ 0.000000] .bss : 0xc065d574 - 0xc06c680c ( 421 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 9.288978] Calibrating delay loop... 1059.22 BogoMIPS (lpj=5296128)
[ 9.378746] pid_max: default: 32768 minimum: 301
[ 9.378863] Security Framework initialized
[ 9.378940] Mount-cache hash table entries: 512
[ 9.379645] Initializing cgroup subsys devices
[ 9.379672] Initializing cgroup subsys freezer
[ 9.379687] Initializing cgroup subsys net_cls
[ 9.379701] Initializing cgroup subsys blkio
[ 9.379788] CPU: Testing write buffer coherency: ok
[ 9.380227] Setting up static identity map for 0xc0428fd0 - 0xc042900c
[ 9.382350] devtmpfs: initialized
[ 9.385018] pinctrl core: initialized pinctrl subsystem
[ 9.385389] regulator-dummy: no parameters
[ 9.385743] NET: Registered protocol family 16
[ 9.386237] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 9.386977] cpuidle: using governor ladder
[ 9.386996] cpuidle: using governor menu
[ 9.387117] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 9.387140] Feroceon L2: Enabling L2
[ 9.387183] Feroceon L2: Cache support initialised.
[ 9.391669] bio: create slab <bio-0> at 0
[ 9.392174] vgaarb: loaded
[ 9.392403] usbcore: registered new interface driver usbfs
[ 9.392462] usbcore: registered new interface driver hub
[ 9.392584] usbcore: registered new device driver usb
[ 9.393282] Switched to clocksource orion_clocksource
[ 9.414393] NET: Registered protocol family 2
[ 9.415135] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 9.415200] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 9.415234] TCP: Hash tables configured (established 2048 bind 2048)
[ 9.415308] TCP: reno registered
[ 9.415323] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 9.415347] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 9.415575] NET: Registered protocol family 1
[ 9.415923] RPC: Registered named UNIX socket transport module.
[ 9.415935] RPC: Registered udp transport module.
[ 9.415942] RPC: Registered tcp transport module.
[ 9.415950] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 9.416189] Unpacking initramfs...
[ 10.025836] Freeing initrd memory: 6384K (c1101000 - c173d000)
[ 10.025956] NetWinder Floating Point Emulator V0.97 (double precision)
[ 10.026633] audit: initializing netlink socket (disabled)
[ 10.026687] type=2000 audit(0.730:1): initialized
[ 10.027536] zbud: loaded
[ 10.027691] VFS: Disk quotas dquot_6.5.2
[ 10.027747] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 10.028146] NFS: Registering the id_resolver key type
[ 10.028258] Key type id_resolver registered
[ 10.028268] Key type id_legacy registered
[ 10.028288] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 10.028473] jffs2: version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
[ 10.028779] msgmni has been set to 493
[ 10.030930] alg: No test for stdrng (krng)
[ 10.031034] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 10.031047] io scheduler noop registered
[ 10.031056] io scheduler deadline registered
[ 10.031082] io scheduler cfq registered (default)
[ 10.031314] mv_xor mv_xor.0: Marvell shared XOR driver
[ 10.063359] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 10.103351] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 10.103464] mv_xor mv_xor.1: Marvell shared XOR driver
[ 10.143349] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 10.183348] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 10.183635] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 10.204289] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 1250000A
[ 10.715407] console [ttyS0] enabled
[ 10.719825] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128Mi4
[ 10.731915] Scanning device for bad blocks
[ 10.746207] Bad eraseblock 135 at 0x0000010e0000
[ 10.757483] Bad eraseblock 224 at 0x000001c00000
[ 10.776850] Bad eraseblock 421 at 0x0000034a0000
[ 10.826606] 4 cmdlinepart partitions found on MTD device orion_nand
[ 10.832899] Creating 4 MTD partitions on "orion_nand":
[ 10.838084] 0x000000000000-0x000000100000 : "u-boot"
[ 10.843365] 0x000000100000-0x000000500000 : "uImage"
[ 10.848589] 0x000000500000-0x000002500000 : "rootfs"
[ 10.853873] 0x000002500000-0x000008000000 : "data"
[ 10.859592] libphy: Fixed MDIO Bus: probed
[ 10.863734] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.870290] ehci-pci: EHCI PCI platform driver
[ 10.874823] ehci-orion: EHCI orion driver
[ 10.878913] orion-ehci orion-ehci.0: EHCI Host Controller
[ 10.884386] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 10.892149] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 10.913319] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 10.919447] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 10.926292] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.933565] usb usb1: Product: EHCI Host Controller
[ 10.938467] usb usb1: Manufacturer: Linux 3.12.0-kirkwood-tld-3 ehci_hcd
[ 10.945215] usb usb1: SerialNumber: orion-ehci.0
[ 10.950342] hub 1-0:1.0: USB hub found
[ 10.954174] hub 1-0:1.0: 1 port detected
[ 10.958632] mousedev: PS/2 mouse device common for all mice
[ 11.273342] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 11.425037] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 11.431786] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 11.438992] usb 1-1: Product: USB2.0 Hub
[ 11.443656] hub 1-1:1.0: USB hub found
[ 11.447784] hub 1-1:1.0: 4 ports detected
[ 11.733662] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 11.844286] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5571
[ 11.851210] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 11.858588] usb 1-1.4: Product: Cruzer Fit
[ 11.862707] usb 1-1.4: Manufacturer: SanDisk
[ 11.867016] usb 1-1.4: SerialNumber: 4C530007601009112030
[ 11.973317] rtc-mv rtc-mv: internal RTC not ticking
[ 11.978328] i2c /dev entries driver
[ 11.982452] drop_monitor: Initializing network drop monitor service
[ 11.989112] TCP: cubic registered
[ 11.992444] NET: Registered protocol family 17
[ 11.997033] Key type dns_resolver registered
[ 12.001849] registered taskstats version 1
[ 12.006861] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 12.014206] Freeing unused kernel memory: 204K (c05d5000 - c0608000)
Loading, please wait...
[ 12.093988] udevd[52]: starting version 175
[ 12.183183] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 12.274971] libphy: PHY orion-mdio-mii:00 not found
[ 12.279933] platform mv643xx_eth_port.0: Driver mv643xx_eth_port requests probe dl
[ 12.332309] SCSI subsystem initialized
[ 12.378825] libphy: orion_mdio_bus: probed
[ 12.407096] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 12.465363] mvsdio mvsdio: no pins associated
[ 12.504349] mvsdio mvsdio: lacking card detect (fall back to polling)
[ 12.523146] scsi0 : usb-storage 1-1.4:1.0
[ 12.546490] usbcore: registered new interface driver usb-storage
[ 13.544651] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 6
[ 13.615596] sd 0:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 13.633332] sd 0:0:0:0: [sda] Write Protect is off
[ 13.638938] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn'tA
[ 13.669682] sda: sda1 sda2
[ 13.682969] sd 0:0:0:0: [sda] Attached SCSI disk
[ 13.688137] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:0
[ 13.713089] sd 0:0:0:0: Attached scsi generic sg0 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 22.864354] EXT2-fs (sda1): warning: mounting ext3 filesystem as ext2
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 24.080998] udevd[240]: start5
. ok
[....] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[ 24.599539] alg: hash: Test 1 fai1
[ 24.609125] 00000000: 0c aa 9f d5 37 c3 79 3a 91 d9 21 5f 42 2b 2c 24
[ 24.621957] 00000010: b7 c3 16 0c
[ 24.648365] orion_wdt: Initial timeout 21 sec
done.
[....] Activating swap...done.
[....] Checking root file system...fsck from util-linux 2.20.1
/dev/sda1: clean, 13046/786432 files, 159814/3145728 blocks
done.
[....] Loading kernel modules...done.
[....] Cleaning up temporary files... /tmp /lib/init/rw. ok
[....] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.20.1
done.
[....] Mounting local filesystems...done.
[....] Activating swapfile swap...done.
[....] Cleaning up temporary files.... ok
[....] Setting kernel variables ...done.
[....] Configuring network interfaces...[ 30.537796] NET: Registered protocol fami0
Internet Systems Consortium DHCP Client 4.2.2
Copyright 2004-2011 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

[ 30.687970] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[ 30.694154] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Listening on LPF/eth0/00:25:31:02:1f:60
Sending on LPF/eth0/00:25:31:02:1f:60
Sending on Socket/fallback
DHCPREQUEST on eth0 to 255.255.255.255 port 67
[ 33.963659] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full dud
[ 33.973592] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.201
bound to 192.168.1.35 -- renewal in 33496 seconds.
done.
[....] Starting rpcbind daemon.... ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Cleaning up temporary files.... ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1677 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
[....] Starting system message bus: dbus. ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. ok
[....] Starting NTP server: ntpd. ok
[....] Starting rpcbind daemon...[....] Already running.. ok
1661 (klogd)
. ok
[....] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting OpenBSD Secure Shell server: sshd. ok

Debian GNU/Linux 7 debian ttyS0

debian login:

Try SSH in to IP address 192.168.1.35 as root. Looks like your router assigned this

DHCPREQUEST on eth0 to 255.255.255.255 port 67 
DHCPACK from 192.168.1.201 
bound to 192.168.1.35 -- renewal in 33496 seconds. 
done.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

>Try SSH in to IP address 192.168.1.35 as root. Looks like your router assigned this

i know that works only when the serial cable is attached .... the issue is it will not assign an ip nor is accessible without the serial cable attached when it boots.

If I reboot with the serial cable attached and disconnect the serial cable only after 'hit any key to stop autoboot' at the following point (below) during pogo reboot it will assign an ip an i can access via a network connection without the serial cable. I can not deploy this with such a requirement since will not have a computer nearby.

U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0

It shouldnot behave differently. But you could try to set up static ip after logging in by serial console to see if you can connect with ssh.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

tried with static ip ... still same issue ...

might something be messed up on internal flash that executes before usb thumbnail gets executed?

earlier post I asked about -19 error ... might that be some clue of why it does not boot without serial cable?

Perhaps if that gets resolved might solve my issue?

csspc-pogo Wrote:
-------------------------------------------------------
> tried with static ip ... still same issue ...
>
> might something be messed up on internal flash
> that executes before usb thumbnail gets executed?
>
>
> earlier post I asked about -19 error ... might
> that be some clue of why it does not boot without
> serial cable?
>
> Perhaps if that gets resolved might solve my
> issue?

The error with ubifs is expected. So you can safely ignore it.

The only thing I can think of is your USB thumb drive was not recognized properly without slowing down the boot process. What is boot process looks like in the log where you did not hit any key to stop serial console? how far did it go?

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

what is the name of the log or files I can look at?

Guess if I know their names I will have to power off and put usb thumbnail in a computer and look at them then

I meant the same log of serial console output as in this post:
http://forum.doozan.com/read.php?2,14597,14612#msg-14612

what happen if you did not stop the serial console?

You could also try netconsole:
http://forum.doozan.com/read.php?3,14
to see if it behaves differently.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 01/02/2014 12:52PM by bodhi.