Debian on D-Link DNS-325 - possible! August 09, 2015 11:05AM |
Registered: 9 years ago Posts: 295 |
** MARVELL BOARD: DB-88F6281A-BP LE U-Boot 1.1.4 (May 16 2011 - 10:40:38) Marvell version: 3.4.14.DNS-325.03 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE80 Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> Marvell>> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootfstype=ext4' Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Marvell>> fatload usb 0:1 0x800000 /uImage reading /uImage ....................................................................................................................... 3061607 bytes read Marvell>> fatload usb 0:1 0x1100000 /uInitrd reading /uInitrd ................................................................................................. ....................................................................................................................... 7119407 bytes read Marvell>> bootm 0x800000 0x1100000 ## Booting image at 00800000 ... Image Name: Linux-4.0.0-kirkwood-tld-2 Created: 2015-08-09 15:46:10 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3061543 Bytes = 2.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.0.0-kirkwood-tld-2 Created: 2015-08-09 15:46:37 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7119343 Bytes = 6.8 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK
... Marvell>> bootm 0x800000 0x1100000 ## Booting image at 00800000 ... Image Name: Linux-4.1.0-kirkwood-tld-1 Created: 2015-08-09 16:54:29 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3095607 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.1.0-kirkwood-tld-1 Created: 2015-08-09 16:54:34 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7128450 Bytes = 6.8 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK
Re: Debian on D-Link DNS-325 ? August 09, 2015 12:51PM |
Registered: 9 years ago Posts: 295 |
./kwboot -t -B 115200 /dev/ttyUSB1 -b /data/uboot.2013.10-tld-1-test.nsa325.uart.kwb Sending boot message. Please reboot the target...| Sending boot image... 0 % [......................................................................] 3 % [......................................................................] 5 % [......................................................................] 8 % [......................................................................] 11 % [......................................................................] 14 % [......................................................................] 17 % [......................................................................] 20 % [......................................................................] 23 % [......................................................................] 26 % [......................................................................] 29 % [......................................................................] 32 % [......................................................................] 35 % [......................................................................] 38 % [......................................................................] 41 % [......................................................................] 44 % [......................................................................] 47 % [......................................................................] 50 % [......................................................................] 53 % [......................................................................] 56 % [......................................................................] 59 % [......................................................................] 62 % [......................................................................] 65 % [......................................................................] 68 % [......................................................................] 71 % [......................................................................] 74 % [......................................................................] 77 % [......................................................................] 80 % [......................................................................] 83 % [......................................................................] 85 % [......................................................................] 88 % [......................................................................] 91 % [......................................................................] 94 % [......................................................................] 97 % [.....................................................] [Type Ctrl-\ + c to quit] U-Boot 2013.10-tld-1-uart (Aug 15 2014 - 02:26:46) ZyXEL NSA325 2-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 Warning: failed to set MAC address PHY reset timed out MV88E1318 PHY initialized on egiga0 NSA325>
NSA325> setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootfstype=ext4' NSA325> usb start (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found NSA325> fatload usb 0:1 0x800000 /uImage reading /uImage 3095671 bytes read in 148 ms (19.9 MiB/s) NSA325> fatload usb 0:1 0x1100000 /uInitrd reading /uInitrd 7128514 bytes read in 288 ms (23.6 MiB/s) NSA325> bootm 0x800000 0x1100000 ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.1.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3095607 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.1.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7128450 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.1.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 PREEMPT Sun Jun 28 01:12:41 PDT 2015 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: D-Link DNS-325 NAS (Rev A1) [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootfstype=ext4 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 503700K/524288K available (5877K kernel code, 561K rwdata, 1964K rodata, 284K init, 302K bss, 20588K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07b07a0 (7842 kB) [ 0.000000] .init : 0xc07b1000 - 0xc07f8000 ( 284 kB) [ 0.000000] .data : 0xc07f8000 - 0xc0884434 ( 562 kB) [ 0.000000] .bss : 0xc0884434 - 0xc08cff94 ( 303 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000010] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000450] Console: colour dummy device 80x30 [ 0.000485] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090112] pid_max: default: 32768 minimum: 301 [ 0.090256] Security Framework initialized [ 0.090405] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090431] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091267] Initializing cgroup subsys blkio [ 0.091302] Initializing cgroup subsys devices [ 0.091329] Initializing cgroup subsys freezer [ 0.091366] Initializing cgroup subsys net_cls [ 0.091478] CPU: Testing write buffer coherency: ok [ 0.091969] Setting up static identity map for 0x8200 - 0x8258 [ 0.092322] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.096760] devtmpfs: initialized [ 0.103562] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.104095] prandom: seed boundary self test passed [ 0.107855] prandom: 100 self tests passed [ 0.108011] pinctrl core: initialized pinctrl subsystem [ 0.109534] NET: Registered protocol family 16 [ 0.109962] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.140118] cpuidle: using governor ladder [ 0.170117] cpuidle: using governor menu [ 0.170558] Feroceon L2: Enabling L2 [ 0.170608] Feroceon L2: Cache support initialised. [ 0.171049] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.176778] No ATAGs? [ 0.211713] vgaarb: loaded [ 0.212109] usbcore: registered new interface driver usbfs [ 0.212194] usbcore: registered new interface driver hub [ 0.212264] usbcore: registered new device driver usb [ 0.213391] Switched to clocksource orion_clocksource [ 0.269757] NET: Registered protocol family 2 [ 0.270561] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.270626] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.270684] TCP: Hash tables configured (established 4096 bind 4096) [ 0.270762] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.270787] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.270989] NET: Registered protocol family 1 [ 0.271408] RPC: Registered named UNIX socket transport module. [ 0.271420] RPC: Registered udp transport module. [ 0.271428] RPC: Registered tcp transport module. [ 0.271436] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.271746] Unpacking initramfs... [ 0.916892] Freeing initrd memory: 6964K (c1100000 - c17cd000) [ 0.917006] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.918514] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.918548] Initialise system trusted keyring [ 0.918671] audit: initializing netlink subsys (disabled) [ 0.918733] audit: type=2000 audit(0.910:1): initialized [ 0.919617] zpool: loaded [ 0.919637] zbud: loaded [ 0.919944] VFS: Disk quotas dquot_6.6.0 [ 0.920017] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.920687] NFS: Registering the id_resolver key type [ 0.920746] Key type id_resolver registered [ 0.920756] Key type id_legacy registered [ 0.920788] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.920806] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.921040] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.921541] Key type big_key registered [ 0.924616] alg: No test for stdrng (krng) [ 0.924661] Key type asymmetric registered [ 0.924677] Asymmetric key parser 'x509' registered [ 0.924768] bounce: pool size: 64 pages [ 0.924872] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.924894] io scheduler noop registered [ 0.924908] io scheduler deadline registered [ 0.924961] io scheduler cfq registered (default) [ 0.926453] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.927195] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated [ 0.927647] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated [ 0.928228] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.963474] mv_xor f1060800.xor: Marvell XOR: ( xor cpy ) [ 1.003465] mv_xor f1060800.xor: Marvell XOR: ( xor cpy ) [ 1.003669] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.043455] mv_xor f1060900.xor: Marvell XOR: ( xor cpy ) [ 1.083454] mv_xor f1060900.xor: Marvell XOR: ( xor cpy ) [ 1.083907] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.085295] console [ttyS0] disabled [ 1.085363] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 27, base_baud = 12500000) is a 16550A [ 1.692200] console [ttyS0] enabled [ 1.697066] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 1.703492] nand: Samsung NAND 128MiB 3,3V 8-bit [ 1.708129] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.715759] Scanning device for bad blocks [ 1.797364] Bad eraseblock 804 at 0x000006480000 [ 1.802720] Bad eraseblock 812 at 0x000006580000 [ 1.835337] libphy: Fixed MDIO Bus: probed [ 1.839828] libphy: orion_mdio_bus: probed [ 1.849253] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.934107] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:00:00:00:00:00 [ 2.943143] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.949766] ehci-pci: EHCI PCI platform driver [ 2.954326] ehci-orion: EHCI orion driver [ 2.958547] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.964122] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.971999] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 2.993429] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.999704] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.006559] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.013839] usb usb1: Product: EHCI Host Controller [ 3.018738] usb usb1: Manufacturer: Linux 4.1.0-kirkwood-tld-1 ehci_hcd [ 3.025399] usb usb1: SerialNumber: f1050000.ehci [ 3.030903] hub 1-0:1.0: USB hub found [ 3.034767] hub 1-0:1.0: 1 port detected [ 3.039651] mousedev: PS/2 mouse device common for all mice [ 3.046018] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 3.053101] i2c /dev entries driver [ 3.059305] hidraw: raw HID events driver (C) Jiri Kosina [ 3.065178] drop_monitor: Initializing network drop monitor service [ 3.071729] NET: Registered protocol family 17 [ 3.076363] Key type dns_resolver registered [ 3.081524] Loading compiled-in X.509 certificates [ 3.086410] registered taskstats version 1 [ 3.091600] rtc-mv f1010300.rtc: setting system clock to 2015-08-09 18:16:11 UTC (1439144171) [ 3.102690] Freeing unused kernel memory: 284K (c07b1000 - c07f8000) Loading, please wait... [ 3.182296] systemd-udevd[60]: starting version 215 [ 3.195679] random: systemd-udevd urandom read with 5 bits of entropy available [ 3.352701] SCSI subsystem initialized [ 3.356676] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 3.448217] sata_mv f1080000.sata: slots 32 ports 2 [ 3.488171] scsi host0: sata_mv [ 3.502595] scsi host1: sata_mv [ 3.513916] ata1: SATA max UDMA/133 irq 33 [ 3.518893] usb 1-1: New USB device found, idVendor=14cd, idProduct=8601 [ 3.530659] usb 1-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0 [ 3.546071] usb 1-1: Product: USB 2.0 Hub [ 3.551181] usb 1-1: Manufacturer: USB Device [ 3.556770] ata2: SATA max UDMA/133 irq 33 [ 3.566419] hub 1-1:1.0: USB hub found [ 3.573535] hub 1-1:1.0: 4 ports detected [ 3.863636] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 3.903433] ata1: SATA link down (SStatus 0 SControl F300) [ 3.996006] usb 1-1.2: New USB device found, idVendor=090c, idProduct=1000 [ 4.002928] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.010309] usb 1-1.2: Product: USB Flash Disk [ 4.014790] usb 1-1.2: Manufacturer: General [ 4.019078] usb 1-1.2: SerialNumber: 0467QLBZ31IQ5MSE [ 4.034837] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 4.041530] scsi host2: usb-storage 1-1.2:1.0 [ 4.047935] usbcore: registered new interface driver usb-storage [ 4.057293] usbcore: registered new interface driver uas [ 4.273438] ata2: SATA link down (SStatus 0 SControl F300) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Waiting for root file system ... [ 5.303998] scsi 2:0:0:0: Direct-Access General USB Flash Disk 1100 PQ: 0 ANSI: 4 [ 5.321953] sd 2:0:0:0: [sda] 15669248 512-byte logical blocks: (8.02 GB/7.47 GiB) [ 5.330662] sd 2:0:0:0: [sda] Write Protect is off [ 5.336533] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.355402] sda: sda1 sda2 sda3 Begin: Running /scripts/local-bl[ 5.365955] sd 2:0:0:0: [sda] Attached SCSI removable disk ock ... done. [ 5.379282] sd 2:0:0:0: Attached scsi generic sg0 type 0 Begin: Running /scripts/local-block ... done. done. Begin: Checking root file system ... fsck from util-linux 2.25.2 rootfs: clean, 77703/456960 files, 319079/1827328 blocks done. [ 6.650076] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 8.084316] systemd-udevd[272]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 8.528983] MV-CESA:Fallback driver 'hmac(sha1)' could not be loaded! [ 8.536955] lm75 0-0048: hwmon0: sensor 'lm75' [ 8.541483] alg: hash: Failed to load transform for mv-hmac-sha1: -2 [ 8.587969] orion_wdt: Initial timeout 21 sec [ 9.617188] random: nonblocking pool is initialized done. [ ok ] Setting parameters of disc: (none). [....] Activating swap...[ 10.303912] Adding 262140k swap on /dev/sda2. Priority:-1 extents:1 across:262140k FS done. [ 10.432113] EXT4-fs (sda3): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 77703/456960 files, 319079/1827328 blocks done. [ 10.650720] EXT4-fs (sda3): re-mounted. Opts: (null) [ ok ] Activating lvm and md swap...done. ... ... [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [....] Mounting local filesystems...mount: special device /dev/disk/by-label/data does not exist failed. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 18.407453] NET: Registered protocol family 10 [ 19.587423] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/b0:b2:dc:39:cf:ea Sending on LPF/eth0/b0:b2:dc:39:cf:ea Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 [ 21.838815] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 21.848754] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPOFFER from 192.168.1.1 DHCPACK from 192.168.1.1 Reloading /etc/samba/smb.conf: smbd. bound to 192.168.1.168 -- renewal in 17840 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... [ ok ] Setting sensors limits. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting system logging: syslog-ng. [ ok ] Starting NetBIOS name server: nmbd. [ ok ] Starting system message bus: dbus. [ ok ] Starting NTP server: ntpd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting p910nd daemon. Please edit /etc/default/p910nd first. ... (warning). [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting SMB/CIFS daemon: smbd. Debian GNU/Linux 8 debianNSA310 ttyS0
Re: Debian on D-Link DNS-325 ? August 09, 2015 02:43PM |
Registered: 9 years ago Posts: 298 |
Re: Debian on D-Link DNS-325 ? August 09, 2015 02:55PM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? August 09, 2015 03:38PM |
Admin Registered: 13 years ago Posts: 18,858 |
Re: Debian on D-Link DNS-325 ? August 09, 2015 03:47PM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? August 09, 2015 03:51PM |
Admin Registered: 13 years ago Posts: 18,858 |
mainlineLinux=yes
Re: Debian on D-Link DNS-325 ? August 09, 2015 05:54PM |
Registered: 9 years ago Posts: 295 |
U-Boot 2012.10-g8aac38e (Aug 10 2015 - 00:17:17) DNS-325 SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Warning: failed to set MAC address Hit any key to stop autoboot: 0
Re: Debian on D-Link DNS-325 ? August 09, 2015 08:08PM |
Admin Registered: 13 years ago Posts: 18,858 |
> > U-Boot 2012.10-g8aac38e (Aug 10 2015 - 00:17:17) > DNS-325 > > SoC: Kirkwood 88F6281_A1 > DRAM: 256 MiB > WARNING: Caches not enabled > NAND: 128 MiB > In: serial > Out: serial > Err: serial > Net: egiga0 > Warning: failed to set MAC address > > Hit any key to stop autoboot: 0 > >
Re: Debian on D-Link DNS-325 ? August 09, 2015 08:27PM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? August 09, 2015 11:04PM |
Admin Registered: 13 years ago Posts: 18,858 |
Re: Debian on D-Link DNS-325 ? August 10, 2015 01:37AM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? August 10, 2015 02:29AM |
Admin Registered: 13 years ago Posts: 18,858 |
Re: Debian on D-Link DNS-325 - possible! August 10, 2015 03:27PM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 - possible! August 10, 2015 04:03PM |
Admin Registered: 13 years ago Posts: 18,858 |
Re: Debian on D-Link DNS-325 - possible! December 15, 2015 05:02AM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? December 26, 2015 12:04PM |
Registered: 9 years ago Posts: 295 |
Preparing kirkwood boot image to boot from uart Nand ECC mode = default Nand page size = 0x800 Image Type: Kirkwood Boot from Serial port Image Data Size: 410180 Bytes = 400.57 kB = 0.39 MB Load Address: 00600000 Entry Point: 00600000
Re: Debian on D-Link DNS-325 ? December 26, 2015 12:26PM |
Registered: 9 years ago Posts: 295 |
./kwboot -t -B 115200 /dev/ttyUSB0 -b u-boot.kwb Sending boot message. Please reboot the target...| Sending boot image... 0 % [......................................................................] 2 % [......................................................................] 4 % [......................................................................] 6 % [......................................................................] 8 % [......................................................................] 10 % [......................................................................] 13 % [......................................................................] 15 % [......................................................................] 17 % [......................................................................] 19 % [......................................................................] 21 % [......................................................................] 24 % [......................................................................] 26 % [......................................................................] 28 % [......................................................................] 30 % [......................................................................] 32 % [......................................................................] 34 % [......................................................................] 37 % [......................................................................] 39 % [......................................................................] 41 % [......................................................................] 43 % [......................................................................] 45 % [......................................................................] 48 % [......................................................................] 50 % [......................................................................] 52 % [......................................................................] 54 % [......................................................................] 56 % [......................................................................] 58 % [......................................................................] 61 % [......................................................................] 63 % [......................................................................] 65 % [......................................................................] 67 % [......................................................................] 69 % [......................................................................] 72 % [......................................................................] 74 % [......................................................................] 76 % [......................................................................] 78 % [......................................................................] 80 % [......................................................................] 82 % [......................................................................] 85 % [......................................................................] 87 % [......................................................................] 89 % [......................................................................] 91 % [......................................................................] 93 % [......................................................................] 96 % [......................................................................] 98 % [...........................................................] [Type Ctrl-\ + c to quit] U-Boot 2012.04.01-g415d386-dirty (Dec 26 2015 - 19:14:51) D-Link DNS-325 SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0
[[ 0.000000] Linux version 4.3.2-kirkwood-rm-1 (root@debianNSA325v2) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Tue Dec 15 01:04:40 CET 2015 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: D-Link DNS-325 NAS (Rev A1)
Re: Debian on D-Link DNS-325 ? December 26, 2015 03:34PM |
Admin Registered: 13 years ago Posts: 18,858 |
./linux-4.2-tld/arch/arm/boot/dts/kirkwood-dns325.dts ./linux-4.2-tld/arch/arm/boot/dts/kirkwood-dnskw.dtsi
Re: Debian on D-Link DNS-325 ? December 26, 2015 06:53PM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? December 27, 2015 01:21AM |
Admin Registered: 13 years ago Posts: 18,858 |
Re: Debian on D-Link DNS-325 ? December 28, 2015 04:28AM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? December 28, 2015 06:06PM |
Registered: 9 years ago Posts: 295 |
U-Boot 2012.04.01-g415d386 (Dec 26 2015 - 19:40:55) D-Link DNS-325 SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 => ide reset Reset IDE: Bus 0: ....OK Bus 1: OK Device 0: Model: WDC WD5000AAKS-00YGA0 Firm: 12.01C02 Ser#: WD-WCAS83787553 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Device 1: Model: WDC WD5000AAKS-00YGA0 Firm: 12.01C02 Ser#: WD-WCAS83787553 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
[ 0.000000] Linux version 4.2.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Aug 31 23:12:00 PDT 2015 ... ... [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootfstype=ext4 mtdparts=orion_nand:0x100000@0(uboot)ro,0x20000@0xA0000(uboot_env) ... ... [ 3.614091] ata1: SATA max UDMA/133 irq 33 [ 3.618220] ata2: SATA max UDMA/133 irq 33 ... ... [ 4.123518] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 4.163481] ata1.00: ATA-8: WDC WD5000AAKS-00YGA0, 12.01C02, max UDMA/133 [ 4.170310] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 4.233477] ata1.00: configured for UDMA/133 [ 4.253784] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 1C02 PQ: 0 ANSI: 5 [ 5.303757] scsi 2:0:0:0: Direct-Access General USB Flash Disk 1100 PQ: 0 ANSI: 4 [ 5.320085] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 5.329096] sd 2:0:0:0: [sdb] 15851520 512-byte logical blocks: (8.11 GB/7.55 GiB) [ 5.337816] sd 0:0:0:0: [sda] Write Protect is off [ 5.342829] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.352320] sd 2:0:0:0: [sdb] Write Protect is off [ 5.360071] sd 2:0:0:0: [sdb] No Caching mode page found [ 5.365483] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 5.378442] sdb: sdb1 sdb2 sdb3 [ 5.386193] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 5.404416] sda: sda1 sda2 [ 5.409569] sd 0:0:0:0: [sda] Attached SCSI disk [ 9.813426] ata2: link is slow to respond, please be patient (ready=0) [ 10.593440] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 11.133469] ata2.00: ATA-8: WDC WD5000AAKX-001CA0, 15.01H15, max UDMA/133 [ 11.140292] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 11.183471] ata2.00: configured for UDMA/133 [ 11.203763] scsi 1:0:0:0: Direct-Access ATA WDC WD5000AAKX-0 1H15 PQ: 0 ANSI: 5 [ 11.213599] sd 1:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 11.222257] sd 1:0:0:0: [sdc] Write Protect is off [ 11.227290] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.255094] sdc: sdc1 sdc2 [ 11.260167] sd 1:0:0:0: [sdc] Attached SCSI disk [ 11.267703] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 11.289041] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 11.320272] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 0.000000] Linux version 4.3.2-kirkwood-rm-1 (root@debianNSA325v2) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Tue Dec 15 01:04:40 CET 2015 ... ... [ 3.218250] ata1: SATA max UDMA/133 irq 33 [ 3.237201] ata2: SATA max UDMA/133 irq 33 ... ... [ 3.727535] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 3.763552] ata1.00: ATA-8: WDC WD5000AAKS-00YGA0, 12.01C02, max UDMA/133 [ 3.770401] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 3.799555] ata1.00: configured for UDMA/133 [ 3.820090] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 1C02 PQ: 0 ANSI: 5 [ 4.147514] ata2: SATA link down (SStatus 0 SControl F300) [ 4.186105] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 4.195097] sd 0:0:0:0: [sda] Write Protect is off [ 4.200119] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.257076] sda: sda1 sda2 [ 4.262276] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.271282] sd 0:0:0:0: Attached scsi generic sg0 type 0
Re: Debian on D-Link DNS-325 ? December 28, 2015 06:37PM |
Registered: 9 years ago Posts: 295 |
U-Boot 2014.07-gd0a00d5-dirty (Dec 28 2015 - 15:15:42) D-Link DNS-325 SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 => => ide reset Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKS-00YGA0 Firm: 12.01C02 Ser#: WD-WCAS83787553 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
U-Boot 2014.01 (Jan 21 2014 - 18:35:47) D-Link DNS-325 SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 => ide reset Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKS-00YGA0 Firm: 12.01C02 Ser#: WD-WCAS83787553 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) =>
Re: Debian on D-Link DNS-325 ? December 28, 2015 11:39PM |
Admin Registered: 13 years ago Posts: 18,858 |
> > U-Boot 2014.07-gd0a00d5-dirty (Dec 28 2015 - > 15:15:42) > D-Link DNS-325 > > SoC: Kirkwood 88F6281_A1 > DRAM: 256 MiB > WARNING: Caches not enabled > NAND: 128 MiB > In: serial > Out: serial > Err: serial > Net: egiga0 > Hit any key to stop autoboot: 0 > > => > => ide reset > > Reset IDE: Bus 0: OK Bus 1: not available > Device 0: Model: WDC WD5000AAKS-00YGA0 Firm: > 12.01C02 Ser#: WD-WCAS83787553 > Type: Hard Disk > Supports 48-bit addressing > Capacity: 476940.0 MB = 465.7 GB > (976773168 x 512) > >>
> U-Boot 2014.01 (Jan 21 2014 - 18:35:47) > D-Link DNS-325 > > SoC: Kirkwood 88F6281_A1 > DRAM: 256 MiB > WARNING: Caches not enabled > NAND: 128 MiB > In: serial > Out: serial > Err: serial > Net: egiga0 > Hit any key to stop autoboot: 0 > => ide reset > > Reset IDE: Bus 0: OK Bus 1: not available > Device 0: Model: WDC WD5000AAKS-00YGA0 Firm: > 12.01C02 Ser#: WD-WCAS83787553 > Type: Hard Disk > Supports 48-bit addressing > Capacity: 476940.0 MB = 465.7 GB > (976773168 x 512) > => >
Re: Debian on D-Link DNS-325 ? December 29, 2015 07:31AM |
Registered: 9 years ago Posts: 295 |
U-Boot 2014.01 (Jan 21 2014 - 18:35:47) D-Link DNS-325 SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 => md f1010140 f1010140: 00000880 00039604 00000000 00000000 ................ f1010150: 00039884 000398a4 00000000 00000000 ................ f1010160: 00000000 00000000 00000000 00000000 ................ f1010170: 00000000 00000000 00000000 00000000 ................ f1010180: 00000000 00000000 00000000 00000000 ................ f1010190: 00000000 00000000 00000000 00000000 ................ f10101a0: 00000000 00000000 00000000 00000000 ................ f10101b0: 00000000 00000000 00000000 00000000 ................ f10101c0: 00000000 00000000 00000000 00000000 ................ f10101d0: 00000000 00000000 00000000 00000000 ................ f10101e0: 00000000 00000000 00000000 00000000 ................ f10101f0: 00000000 00000000 00000000 00000000 ................ f1010200: 00000000 76543210 3210ba98 000100ff .....2Tv...2.... f1010210: 00000000 00000000 00000000 00000000 ................ f1010220: 00000000 00000000 00000000 00000000 ................ f1010230: 00000000 00000000 00000000 00000000 ................
=> mw.l f1010140 0x02 f1010140: 00000002 00039604 00000000 00000000 ................ f1010150: 00039006 000398a6 00000000 00000000 ................ f1010160: 00000000 00000000 00000000 00000000 ................ f1010170: 00000000 00000000 00000000 00000000 ................ f1010180: 00000000 00000000 00000000 00000000 ................ f1010190: 00000000 00000000 00000000 00000000 ................ f10101a0: 00000000 00000000 00000000 00000000 ................ f10101b0: 00000000 00000000 00000000 00000000 ................ f10101c0: 00000000 00000000 00000000 00000000 ................ f10101d0: 00000000 00000000 00000000 00000000 ................ f10101e0: 00000000 00000000 00000000 00000000 ................ f10101f0: 00000000 00000000 00000000 00000000 ................ f1010200: 00000000 76543210 3210ba98 000100ff .....2Tv...2.... f1010210: 00000000 00000000 00000000 00000000 ................ f1010220: 00000000 00000000 00000000 00000000 ................ f1010230: 00000000 00000000 00000000 00000000 ................ => ide reset Reset IDE: ide_preinit failed
=> mw.l f1010140 0x0880 Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKS-00YGA0 Firm: 12.01C02 Ser#: WD-WCAS83787553 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
[0:0:0:0] disk ATA WDC WD5000AAKS-0 1C02 /dev/sda [1:0:0:0] disk ATA WDC WD5000AAKX-0 1H15 /dev/sdc
[ 3.531529] sata_mv f1080000.sata: version 1.28 [ 3.531840] sata_mv f1080000.sata: slots 32 ports 2 [ 3.575417] scsi host0: sata_mv [ 3.592777] scsi host1: sata_mv [ 3.619308] ata1: SATA max UDMA/133 irq 33 [ 3.657575] ata2: SATA max UDMA/133 irq 33 [ 4.163449] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 4.203473] ata1.00: ATA-8: WDC WD5000AAKS-00YGA0, 12.01C02, max UDMA/133 [ 4.210297] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 4.253475] ata1.00: configured for UDMA/133 [ 9.833423] ata2: link is slow to respond, please be patient (ready=0) [ 10.553440] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 11.153468] ata2.00: ATA-8: WDC WD5000AAKX-001CA0, 15.01H15, max UDMA/133 [ 11.160294] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 11.203475] ata2.00: configured for UDMA/133
Re: Debian on D-Link DNS-325 ? December 30, 2015 01:50AM |
Admin Registered: 13 years ago Posts: 18,858 |
Re: Debian on D-Link DNS-325 ? December 30, 2015 06:45AM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? February 01, 2016 08:12AM |
Registered: 9 years ago Posts: 295 |
Re: Debian on D-Link DNS-325 ? February 01, 2016 07:25PM |
Admin Registered: 13 years ago Posts: 18,858 |