Creating bootable USB for Seagate GoFlex Home October 22, 2015 01:33PM |
Registered: 8 years ago Posts: 22 |
Re: Creating bootable USB for Seagate GoFlex Home October 22, 2015 04:14PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Creating bootable USB for Seagate GoFlex Home October 22, 2015 04:42PM |
Registered: 8 years ago Posts: 22 |
Re: Creating bootable USB for Seagate GoFlex Home October 22, 2015 05:59PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Creating bootable USB for Seagate GoFlex Home October 22, 2015 11:47PM |
Registered: 8 years ago Posts: 22 |
Re: Creating bootable USB for Seagate GoFlex Home October 23, 2015 12:23AM |
Admin Registered: 13 years ago Posts: 18,821 |
help
Latest u-boot: http://forum.doozan.com/read.php?3,12381about how we should always try booting with UART before flashing new u-boot.
Re: Creating bootable USB for Seagate GoFlex Home October 23, 2015 01:41AM |
Registered: 8 years ago Posts: 22 |
Re: Creating bootable USB for Seagate GoFlex Home October 23, 2015 03:22AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Creating bootable USB for Seagate GoFlex Home: Redux and more October 24, 2015 06:37AM |
Registered: 8 years ago Posts: 22 |
Re: Creating bootable USB for Seagate GoFlex Home: Redux and more October 24, 2015 04:14PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Creating bootable USB for Seagate GoFlex Home October 26, 2015 11:15PM |
Registered: 8 years ago Posts: 22 |
Re: Creating bootable USB for Seagate GoFlex Home October 27, 2015 11:52PM |
Registered: 8 years ago Posts: 22 |
U-Boot 2014.07-tld-2 (Sep 20 2014 - 01:04:12) Seagate GoFlex Home SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 10 9 8 7 6 5 4 3 2 1 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Unknown command 'mmc' - try 'help' Reset IDE: ide_preinit failed no USB devices available Unknown command 'mmc' - try 'help' no IDE devices available (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Unknown command 'mmc' - try 'help' ** Bad device mmc 0 ** ** Bad device mmc 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Reset IDE: ide_preinit failed ** Bad device size - ide 0 ** ** Bad device size - ide 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! resetting ...
GoFlexHome> printenv arcNumber=2097 baudrate=115200 bootcmd=run bootcmd_uenv; run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=b6:d0:5e:0f:a1:17 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking machid=0x831 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.0.220 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 Environment size: 2827/131068 bytes
Re: Creating bootable USB for Seagate GoFlex Home October 28, 2015 12:45AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Creating bootable USB for Seagate GoFlex Home October 30, 2015 12:12AM |
Registered: 8 years ago Posts: 22 |
mmc_root=LABEL=mmcrootfs sata_root=LABEL=satarootfs usb_root=LABEL=usbrootfs load_dtb=ext2load ide 0:1 0x1c00000 /boot/dts/kirkwood-goflexnet.dtb
U-Boot 2014.07-tld-2 (Sep 20 2014 - 01:04:12) Seagate GoFlex Home SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 10 9 8 7 6 5 4 3 2 1 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Unknown command 'mmc' - try 'help' Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 30279680 00087895-01 83 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Unknown command 'mmc' - try 'help' no IDE devices available (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 2865664 bytes read in 429 ms (6.4 MiB/s) 6535284 bytes read in 615 ms (10.1 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.18.5-kirkwood-tld-1 Created: 2015-02-08 9:02:01 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2865600 Bytes = 2.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.18.5-kirkwood-tld-1 Created: 2015-02-19 1:49:36 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6535220 Bytes = 6.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0x831 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000831). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
Re: Creating bootable USB for Seagate GoFlex Home: Redux and more October 30, 2015 12:23AM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
Do this:
- Create the Debian 3.16 rootfs
- Log in to the stock OS and mount the new rootfs
- Install new u-boot
Re: Creating bootable USB for Seagate GoFlex Home November 01, 2015 01:27AM |
Registered: 8 years ago Posts: 22 |
arcNumber=2097 machid=0x831 ethaddr=b6:d0:5e:0f:a1:17 ipaddr=192.168.0.231 serverip=192.168.0.220 mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) baudrate=115200 bootcmd=run bootcmd_uenv; run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 if_netconsole=ping $serverip led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
Re: Creating bootable USB for Seagate GoFlex Home November 01, 2015 01:45AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Creating bootable USB for Seagate GoFlex Home November 01, 2015 06:24PM |
Registered: 8 years ago Posts: 22 |
U-Boot 2014.07-tld-2 (Sep 20 2014 - 01:04:12) Seagate GoFlex Home gcc (Debian 4.6.3-14) 4.6.3 GNU ld (GNU Binutils for Debian) 2.22 Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found ** File not found /rescueme ** ** Unrecognized filesystem type ** UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI error: validate_ec_hdr: bad VID header offset 2048, expected 512 UBI error: validate_ec_hdr: bad EC header UBI error: ubi_io_read_ec_hdr: validation failed for PEB 0 UBI error: ubi_init: cannot attach mtd1 UBI error: ubi_init: UBI error: cannot initialize UBI, error -22 UBI init error 22 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 2756040 bytes read in 431 ms (6.1 MiB/s) 6032465 bytes read in 587 ms (9.8 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2755976 Bytes = 2.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6032401 Bytes = 5.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
Re: Creating bootable USB for Seagate GoFlex Home November 01, 2015 08:44PM |
Registered: 8 years ago Posts: 22 |
U-Boot 2014.07-tld-2 (Sep 20 2014 - 01:04:12) Seagate GoFlex Home SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Using egiga0 device host 192.168.1.53 is alive Using egiga0 device host 192.168.1.53 is alive Using egiga0 device host 192.168.1.53 is alive Using egiga0 device host 192.168.1.53 is alive Using egiga0 device host 192.168.1.53 is alive Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.16.0-kirkwood-tld-2 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #2 PREEMPT Sun Aug 31 18:56:01 PDT 2014 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Seagate GoFlex Home [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 115744K/131072K available (5441K kernel code, 397K rwdata, 1840K rodata, 257K init, 299K bss, 15328K reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07248b0 (7283 kB) [ 0.000000] .init : 0xc0725000 - 0xc0765444 ( 258 kB) [ 0.000000] .data : 0xc0766000 - 0xc07c975c ( 398 kB) [ 0.000000] .bss : 0xc07c975c - 0xc08144dc ( 300 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:114 [ 0.000011] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns [ 14.806946] Console: colour dummy device 80x30 [ 14.806975] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 14.896732] pid_max: default: 32768 minimum: 301 [ 14.896850] Security Framework initialized [ 14.896919] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 14.896937] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 14.897814] Initializing cgroup subsys devices [ 14.897875] Initializing cgroup subsys freezer [ 14.897905] Initializing cgroup subsys net_cls [ 14.897952] Initializing cgroup subsys blkio [ 14.898049] CPU: Testing write buffer coherency: ok [ 14.898519] Setting up static identity map for 0x5273f0 - 0x527448 [ 14.900891] devtmpfs: initialized [ 14.904869] prandom: seed boundary self test passed [ 14.908934] prandom: 100 self tests passed [ 14.908965] pinctrl core: initialized pinctrl subsystem [ 14.909478] regulator-dummy: no parameters [ 14.909943] NET: Registered protocol family 16 [ 14.910399] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 14.911649] cpuidle: using governor ladder [ 14.911676] cpuidle: using governor menu [ 14.911816] Kirkwood: MV88F6281-A1, TCLK=200000000. [ 14.911840] Feroceon L2: Enabling L2 [ 14.911880] Feroceon L2: Cache support initialised. [ 14.948257] vgaarb: loaded [ 14.948615] usbcore: registered new interface driver usbfs [ 14.948692] usbcore: registered new interface driver hub [ 14.948816] usbcore: registered new device driver usb [ 14.949812] Switched to clocksource orion_clocksource [ 14.988589] NET: Registered protocol family 2 [ 14.989577] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 14.989603] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 14.989622] TCP: Hash tables configured (established 1024 bind 1024) [ 14.989694] TCP: reno registered [ 14.989708] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 14.989730] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 14.989994] NET: Registered protocol family 1 [ 14.990333] RPC: Registered named UNIX socket transport module. [ 14.990344] RPC: Registered udp transport module. [ 14.990352] RPC: Registered tcp transport module. [ 14.990359] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 14.990667] Unpacking initramfs... [ 15.493014] Freeing initrd memory: 5884K (c1101000 - c16c0000) [ 15.493154] NetWinder Floating Point Emulator V0.97 (double precision) [ 15.494315] futex hash table entries: 256 (order: -1, 3072 bytes) [ 15.494384] audit: initializing netlink subsys (disabled) [ 15.494440] audit: type=2000 audit(0.680:1): initialized [ 15.495262] zbud: loaded [ 15.495539] VFS: Disk quotas dquot_6.5.2 [ 15.495592] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 15.496158] NFS: Registering the id_resolver key type [ 15.496217] Key type id_resolver registered [ 15.496227] Key type id_legacy registered [ 15.496253] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 15.496268] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 15.496437] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 15.496750] msgmni has been set to 237 [ 15.496904] Key type big_key registered [ 15.499260] alg: No test for stdrng (krng) [ 15.499377] bounce: pool size: 64 pages [ 15.499443] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 15.499463] io scheduler noop registered [ 15.499477] io scheduler deadline registered [ 15.499645] io scheduler cfq registered (default) [ 15.500157] mv_xor mv_xor.0: Marvell shared XOR driver [ 15.539891] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 15.579879] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 15.580054] mv_xor mv_xor.1: Marvell shared XOR driver [ 15.619877] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 15.659876] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 15.660312] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 15.661315] console [ttyS0] disabled [ 15.681415] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A [ 16.228760] console [ttyS0] enabled [ 16.233691] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 16.240103] nand: Micron MT29F2G08AAD [ 16.243780] nand: 256MiB, SLC, page size: 2048, OOB size: 64 [ 16.249474] Scanning device for bad blocks [ 16.472289] 4 cmdlinepart partitions found on MTD device orion_nand [ 16.478583] Creating 4 MTD partitions on "orion_nand": [ 16.483768] 0x000000000000-0x000000100000 : "u-boot" [ 16.489150] 0x000000100000-0x000000500000 : "uImage" [ 16.494531] 0x000000500000-0x000002500000 : "rootfs" [ 16.499915] 0x000002500000-0x000010000000 : "data" [ 16.506043] libphy: Fixed MDIO Bus: probed [ 16.522757] libphy: orion_mdio_bus: probed [ 16.526988] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 17.610961] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:10:75:28:59:e4 [ 17.619955] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 17.626514] ehci-pci: EHCI PCI platform driver [ 17.631061] ehci-orion: EHCI orion driver [ 17.635167] orion-ehci orion-ehci.0: EHCI Host Controller [ 17.640639] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 17.648366] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 17.669848] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 17.675986] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 17.682831] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 17.690106] usb usb1: Product: EHCI Host Controller [ 17.695008] usb usb1: Manufacturer: Linux 3.16.0-kirkwood-tld-2 ehci_hcd [ 17.701754] usb usb1: SerialNumber: orion-ehci.0 [ 17.707139] hub 1-0:1.0: USB hub found [ 17.710992] hub 1-0:1.0: 1 port detected [ 17.715812] mousedev: PS/2 mouse device common for all mice [ 17.721962] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0 [ 17.727973] i2c /dev entries driver [ 17.732477] hidraw: raw HID events driver (C) Jiri Kosina [ 17.738237] drop_monitor: Initializing network drop monitor service [ 17.744813] TCP: cubic registered [ 17.748154] NET: Registered protocol family 17 [ 17.752799] Key type dns_resolver registered [ 17.757821] registered taskstats version 1 [ 17.762966] rtc-mv rtc-mv: setting system clock to 2015-11-02 02:33:57 UTC (1446431637) [ 17.772973] Freeing unused kernel memory: 256K (c0725000 - c0765000) Loading, please wait... [ 17.850798] udevd[55]: starting version 175 [ 18.007365] SCSI subsystem initialized [ 18.029985] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 18.091932] sata_mv sata_mv.0: cannot get optional clkdev [ 18.097453] sata_mv sata_mv.0: slots 32 ports 1 [ 18.149977] scsi0 : sata_mv [ 18.153158] ata1: SATA max UDMA/133 irq 21 [ 18.204261] usb 1-1: New USB device found, idVendor=18a5, idProduct=0300 [ 18.211026] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 18.218213] usb 1-1: Product: STORE N GO [ 18.222175] usb 1-1: Manufacturer: Verbatim [ 18.226378] usb 1-1: SerialNumber: C70055FB1C5C9655 [ 18.249569] usb-storage 1-1:1.0: USB Mass Storage device detected [ 18.256127] scsi1 : usb-storage 1-1:1.0 [ 18.261835] usbcore: registered new interface driver usb-storage [ 18.271082] usbcore: registered new interface driver uas [ 18.659864] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 18.699887] ata1.00: ATA-8: ST2000DL003-9VT166, CC98, max UDMA/133 [ 18.706101] ata1.00: 3907029168 sectors, multi 0: LBA48 [ 18.769889] ata1.00: configured for UDMA/133 [ 18.790221] scsi 0:0:0:0: Direct-Access ATA ST2000DL003-9VT1 CC98 PQ: 0 ANSI: 5 [ 18.833357] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 18.842285] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 18.847849] sd 0:0:0:0: [sda] Write Protect is off [ 18.853015] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 18.879968] sda: sda1 [ 18.884092] sd 0:0:0:0: [sda] Attached SCSI disk [ 18.900317] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 19.262109] scsi 1:0:0:0: Direct-Access Verbatim STORE N GO 5.00 PQ: 0 ANSI: 6 [ 19.281003] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 19.286559] sd 1:0:0:0: [sdb] 3782639 512-byte logical blocks: (1.93 GB/1.80 GiB) [ 19.302442] sd 1:0:0:0: [sdb] Write Protect is off [ 19.309047] sd 1:0:0:0: [sdb] No Caching mode page found [ 19.314461] sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 19.337901] sdb: sdb1 [ 19.353822] sd 1:0:0:0: [sdb] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. mount: mounting /dev/sda1 on /root failed: Invalid argument Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory done. Target filesystem doesn't have requested /sbin/init. No init found. Try passing init= bootarg. modprobe: module i8042 not found in modules.dep [ 29.349125] uhci_hcd: USB Universal Host Controller Interface driver [ 29.363402] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 29.378237] usbcore: registered new interface driver usbhid [ 29.383971] usbhid: USB HID core driver BusyBox v1.20.2 (Debian 1:1.20.0-7) built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off (initramfs)
Re: Creating bootable USB for Seagate GoFlex Home November 02, 2015 04:01AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Creating bootable USB for Seagate GoFlex Home November 05, 2015 01:56PM |
Registered: 8 years ago Posts: 22 |
Re: Creating bootable USB for Seagate GoFlex Home November 15, 2015 07:37PM |
Registered: 8 years ago Posts: 22 |
bootdelay=2 baudrate=38400 ethaddr=00:11:22:4F:54:54 ipaddr=192.168.1.2 serverip=192.168.1.100 port=0 netboot_cmd=tftp 0x4000000 bootpImage; go 0x4000000 boardtest_state_memory=none cpu_clock=700 netmask=255.255.0.0 bootfile="/tftpboot/uImage" tftp_bsize=512 udp_frag_size=512 whitney_state=saved serialNo=NA6SAARB ethaddr0=00:10:75:40:95:F2 bootargs=console=ttyS0,38400 mem=256M root=/dev/sda3 rw mfgtest_state=final_tested_ok bootcmd=scsi init;ext2load scsi 0:1 0x4000000 uImage;bootm netboot=0 mfgmodel=Seagate Central model_name=cirrus_v1 current_kernel=kernel2 rtclog=522d077b stdin=serial stdout=serial stderr=serial verify=n num_boot_tries=0 uname -a Linux NAS-T1 2.6.35.13-cavm1.whitney-econa.whitney-econa #1 Wed Sep 16 15:47:59 PDT 2015 armv6l GNU/Linux
Re: Creating bootable USB for Seagate GoFlex Home November 16, 2015 03:27AM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
[prepping for possible flameage]