Re: Debian on QiZhiTong 501mv2 August 17, 2017 12:40AM |
Admin Registered: 13 years ago Posts: 18,576 |
[ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017And somehow the statistics snaphot patch was not merged into mainline 4.12.1, but it was ACK in the patch series. Perhaps it is not relevant, and just given out the wrong info.
ifconfig -aDo you see any of the switch ports? if they are there, can you ifup the port that the ethernet cable is plugged in? (lan1,2,3, or 4).
Re: Debian on QiZhiTong 501mv2 August 17, 2017 01:23AM |
Registered: 8 years ago Posts: 166 |
Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=10 root=/dev/sda1 console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506352K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 17936K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000038] Switching to timer-based delay loop, resolution 5ns [ 0.000480] Console: colour dummy device 80x30 [ 0.000511] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000532] pid_max: default: 32768 minimum: 301 [ 0.000724] Security Framework initialized [ 0.000842] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000860] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001666] CPU: Testing write buffer coherency: ok [ 0.002557] Setting up static identity map for 0x100000 - 0x100058 [ 0.002794] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.005853] devtmpfs: initialized [ 0.009661] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.009686] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.010105] prandom: seed boundary self test passed [ 0.013857] prandom: 100 self tests passed [ 0.013868] pinctrl core: initialized pinctrl subsystem [ 0.014928] NET: Registered protocol family 16 [ 0.015320] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.016810] cpuidle: using governor ladder [ 0.016875] cpuidle: using governor menu [ 0.017250] Feroceon L2: Enabling L2 [ 0.017292] Feroceon L2: Cache support initialised. [ 0.017638] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.017745] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.022417] No ATAGs? [ 0.031363] vgaarb: loaded [ 0.031668] SCSI subsystem initialized [ 0.032135] usbcore: registered new interface driver usbfs [ 0.032211] usbcore: registered new interface driver hub [ 0.032297] usbcore: registered new device driver usb [ 0.033336] clocksource: Switched to clocksource orion_clocksource [ 0.121534] VFS: Disk quotas dquot_6.6.0 [ 0.121611] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.132087] NET: Registered protocol family 2 [ 0.132808] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.132868] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.132920] TCP: Hash tables configured (established 4096 bind 4096) [ 0.133001] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.133026] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.133196] NET: Registered protocol family 1 [ 0.133641] RPC: Registered named UNIX socket transport module. [ 0.133653] RPC: Registered udp transport module. [ 0.133660] RPC: Registered tcp transport module. [ 0.133667] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.133985] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.134872] audit: initializing netlink subsys (disabled) [ 0.135314] Initialise system trusted keyrings [ 0.135369] Key type blacklist registered [ 0.135465] audit: type=2000 audit(0.131:1): state=initialized audit_enabled=0 res=1 [ 0.135548] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.135613] zbud: loaded [ 0.136577] NFS: Registering the id_resolver key type [ 0.136604] Key type id_resolver registered [ 0.136612] Key type id_legacy registered [ 0.136629] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.136639] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.136847] jffs2: version 2.2. (NAND) (SUMMARY) 漏 2001-2006 Red Hat, Inc. [ 0.137031] fuse init (API version 7.26) [ 0.137389] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.137647] orangefs_init: module version upstream loaded [ 0.137658] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.553346] random: fast init done [ 6.002881] Key type asymmetric registered [ 6.002896] Asymmetric key parser 'x509' registered [ 6.002958] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.002968] io scheduler noop registered [ 6.002977] io scheduler deadline registered [ 6.003045] io scheduler cfq registered (default) [ 6.004359] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.006109] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.064077] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.064290] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.124067] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.124460] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.125672] console [ttyS0] disabled [ 6.125736] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 13.245571] console [ttyS0] enabled [ 13.295768] loop: module loaded [ 13.333890] sata_mv f1080000.sata: slots 32 ports 1 [ 13.393824] scsi host0: sata_mv [ 13.431625] ata1: SATA max UDMA/133 irq 32 [ 13.481262] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 13.557443] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 13.612715] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 13.700316] Scanning device for bad blocks [ 13.878857] Bad eraseblock 2455 at 0x00000265c000 [ 14.021486] 3 ofpart partitions found on MTD device orion_nand [ 14.091332] Creating 3 MTD partitions on "orion_nand": [ 14.152909] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 14.228202] ata1.00: ATA-7: JMicron, 100415, max UDMA/133 [ 14.228209] ata1.00: 7856128 sectors, multi 1: LBA48 [ 14.293197] ata1.00: configured for UDMA/133 [ 14.354240] scsi 0:0:0:0: Direct-Access ATA JMicron 15 PQ: 0 ANSI: 5 [ 14.355649] sd 0:0:0:0: [sda] 7856128 512-byte logical blocks: (4.02 GB/3.75 GiB) [ 14.355716] sd 0:0:0:0: [sda] Write Protect is off [ 14.355838] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 14.505407] sda: sda1 sda2 [ 14.507081] sd 0:0:0:0: [sda] Attached SCSI disk [ 14.852326] 0x000000000000-0x000000100000 : "u-boot" [ 14.913093] 0x000000100000-0x000000500000 : "kernel" [ 14.974029] 0x000000500000-0x000004000000 : "ubi" [ 15.035906] libphy: Fixed MDIO Bus: probed [ 15.085794] libphy: orion_mdio_bus: probed [ 15.135172] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 15.217857] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 15.322656] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 15.426991] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 15.505219] ehci-pci: EHCI PCI platform driver [ 15.558477] ehci-orion: EHCI orion driver [ 15.606622] orion-ehci f1050000.ehci: EHCI Host Controller [ 15.672410] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 15.764301] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 15.863373] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 15.935506] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 16.016869] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.103392] usb usb1: Product: EHCI Host Controller [ 16.161827] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 16.242130] usb usb1: SerialNumber: f1050000.ehci [ 16.299105] hub 1-0:1.0: USB hub found [ 16.344070] hub 1-0:1.0: 1 port detected [ 16.391608] usbcore: registered new interface driver usb-storage [ 16.463935] mousedev: PS/2 mouse device common for all mice [ 16.531335] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 16.613833] i2c /dev entries driver [ 16.656622] hidraw: raw HID events driver (C) Jiri Kosina [ 16.721740] drop_monitor: Initializing network drop monitor service [ 16.797151] NET: Registered protocol family 17 [ 16.850406] Key type dns_resolver registered [ 16.901589] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 16.982697] registered taskstats version 1 [ 17.031798] Loading compiled-in X.509 certificates [ 17.089327] zswap: loaded using pool lzo/zbud [ 17.143894] Key type big_key registered [ 17.191750] Key type encrypted registered [ 17.241128] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 04:27:56 UTC (946700876) [ 17.342822] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 [ 17.423254] Waiting 10 sec before mounting root device... [ 17.487943] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 17.574275] hub 1-1:1.0: USB hub found [ 17.619317] hub 1-1:1.0: 2 ports detected [ 17.983365] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 18.215937] usb 1-1.1: New USB device found, idVendor=0bda, idProduct=0109 [ 18.298363] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 18.385965] usb 1-1.1: Product: USB2.0-CRW [ 18.435015] usb 1-1.1: Manufacturer: Generic [ 18.486153] usb 1-1.1: SerialNumber: 20090815198100000 [ 18.558884] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 18.634278] scsi host1: usb-storage 1-1.1:1.0 [ 19.764656] scsi 1:0:0:0: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 0 CCS [ 20.409857] sd 1:0:0:0: [sdb] 15261696 512-byte logical blocks: (7.81 GB/7.28 GiB) [ 20.501345] sd 1:0:0:0: [sdb] Write Protect is off [ 20.559468] sd 1:0:0:0: [sdb] No Caching mode page found [ 20.623113] sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 20.700453] sdb: sdb1 [ 20.731467] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 28.003937] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 28.094448] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 28.186249] VFS: Mounted root (ext3 filesystem) readonly on device 8:1. [ 28.268087] devtmpfs: mounted [ 28.306497] Freeing unused kernel memory: 1024K INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. ERROR: could not open /proc/stat: No such file or directory findfs: unable to resolve 'LABEL=rootfs' [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 29.888806] marvell-cesa f1030000.crypto: CESA device successfully registered [ 30.046299] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 30.046929] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 30.065418] usbcore: registered new interface driver uas [ 30.114000] mv88e6085: probe of f1072004.mdio-bus-mii:10 failed with error -110 [ 30.853598] orion_wdt: Initial timeout 21 sec [ 30.908660] mvsdio f1090000.mvsdio: Got CD GPIO done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 31.742111] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean,[ 31.988590] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro 14459/196608 files, 198302/786432 blocks . ok [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files.... [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 34.414353] mv643xx_eth: no PHY [ 34.414390] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:90:0b:19:ee:25 Sending on LPF/eth0/00:90:0b:19:ee:25 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13 DHCPDI[ 96.336083] NET: Registered protocol family 10 SCOVER on eth0 t[ 96.394154] Segment Routing with IPv6 o 255.255.255.255 port 67 interval 13 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. INIT: Entering runlevel: 2ry files... [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1221 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1219 (klogd) . ok [ ok ] Running local boot scripts (/etc/rc.local).
Re: Debian on QiZhiTong 501mv2 August 17, 2017 03:09AM |
Registered: 8 years ago Posts: 166 |
Re: Debian on QiZhiTong 501mv2 August 17, 2017 04:33AM |
Admin Registered: 13 years ago Posts: 18,576 |
.phy_read = mv88e6xxx_g2_smi_phy_read, .phy_write = mv88e6xxx_g2_smi_phy_write,
static const struct mv88e6xxx_ops mv88e6161_ops = { /* MV88E6XXX_FAMILY_6165 */ .set_switch_mac = mv88e6xxx_g2_set_switch_mac, .phy_read = mv88e6165_phy_read, .phy_write = mv88e6165_phy_write,
Re: Debian on QiZhiTong 501mv2 August 18, 2017 04:47PM |
Admin Registered: 13 years ago Posts: 18,576 |
Re: Debian on QiZhiTong 501mv2 August 19, 2017 09:12AM |
Registered: 8 years ago Posts: 166 |
MB302>> run bootcmd4 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: JMicron Firm: 100415 Ser#: 00000000002E9 Type: Hard Disk Supports 48-bit addressing Capacity: 3836.0 MB = 3.7 GB (7856128 x 512) 3815077 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.12.8-kirkwood-tld-1 Created: 2017-08-19 13:59:36 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3815013 Bytes = 3.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.8-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 PREEMPT Thu Aug 17 04:51:51 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=1 root=/dev/sda1 console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506352K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 17936K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db32d4 ( 717 kB) [ 0.000000] .bss : 0xc0db9dac - 0xc0e01fc0 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000041] Switching to timer-based delay loop, resolution 5ns [ 0.000494] Console: colour dummy device 80x30 [ 0.000526] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000549] pid_max: default: 32768 minimum: 301 [ 0.000740] Security Framework initialized [ 0.000875] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000894] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001732] CPU: Testing write buffer coherency: ok [ 0.002610] Setting up static identity map for 0x100000 - 0x100058 [ 0.002851] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.006362] devtmpfs: initialized [ 0.010014] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.010091] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.010446] prandom: seed boundary self test passed [ 0.014648] prandom: 100 self tests passed [ 0.014659] pinctrl core: initialized pinctrl subsystem [ 0.015702] NET: Registered protocol family 16 [ 0.016102] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017531] cpuidle: using governor ladder [ 0.017594] cpuidle: using governor menu [ 0.017983] Feroceon L2: Enabling L2 [ 0.018026] Feroceon L2: Cache support initialised. [ 0.018372] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.018479] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.023129] No ATAGs? [ 0.031964] vgaarb: loaded [ 0.032283] SCSI subsystem initialized [ 0.032738] usbcore: registered new interface driver usbfs [ 0.032813] usbcore: registered new interface driver hub [ 0.032892] usbcore: registered new device driver usb [ 0.033943] clocksource: Switched to clocksource orion_clocksource [ 0.122772] VFS: Disk quotas dquot_6.6.0 [ 0.122848] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.133190] NET: Registered protocol family 2 [ 0.133914] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.134019] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.134072] TCP: Hash tables configured (established 4096 bind 4096) [ 0.134155] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.134178] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.134348] NET: Registered protocol family 1 [ 0.134733] RPC: Registered named UNIX socket transport module. [ 0.134745] RPC: Registered udp transport module. [ 0.134752] RPC: Registered tcp transport module. [ 0.134759] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.135083] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.135965] audit: initializing netlink subsys (disabled) [ 0.136406] Initialise system trusted keyrings [ 0.136462] Key type blacklist registered [ 0.136560] audit: type=2000 audit(0.132:1): state=initialized audit_enabled=0 res=1 [ 0.136643] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.136709] zbud: loaded [ 0.137677] NFS: Registering the id_resolver key type [ 0.137704] Key type id_resolver registered [ 0.137713] Key type id_legacy registered [ 0.137731] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.137740] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.137938] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.138119] fuse init (API version 7.26) [ 0.138510] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.138767] orangefs_init: module version upstream loaded [ 0.138777] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.553951] random: fast init done [ 6.084862] Key type asymmetric registered [ 6.084876] Asymmetric key parser 'x509' registered [ 6.084940] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.084951] io scheduler noop registered [ 6.084960] io scheduler deadline registered [ 6.085030] io scheduler cfq registered (default) [ 6.086274] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.088037] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.144711] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.144922] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.204703] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.205099] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.206306] console [ttyS0] disabled [ 6.206368] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 13.334566] console [ttyS0] enabled [ 13.384658] loop: module loaded [ 13.422751] sata_mv f1080000.sata: slots 32 ports 1 [ 13.482644] scsi host0: sata_mv [ 13.520498] ata1: SATA max UDMA/133 irq 32 [ 13.570130] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 13.646315] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 13.701589] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 13.789188] Scanning device for bad blocks [ 13.967748] Bad eraseblock 2455 at 0x00000265c000 [ 14.110442] 3 ofpart partitions found on MTD device orion_nand [ 14.180309] Creating 3 MTD partitions on "orion_nand": [ 14.241887] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 14.317178] ata1.00: ATA-7: JMicron, 100415, max UDMA/133 [ 14.317185] ata1.00: 7856128 sectors, multi 1: LBA48 [ 14.382173] ata1.00: configured for UDMA/133 [ 14.443117] scsi 0:0:0:0: Direct-Access ATA JMicron 15 PQ: 0 ANSI: 5 [ 14.444540] sd 0:0:0:0: [sda] 7856128 512-byte logical blocks: (4.02 GB/3.75 GiB) [ 14.444606] sd 0:0:0:0: [sda] Write Protect is off [ 14.444724] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 14.594280] sda: sda1 sda2 [ 14.595936] sd 0:0:0:0: [sda] Attached SCSI disk [ 14.941197] 0x000000000000-0x000000100000 : "u-boot" [ 15.001958] 0x000000100000-0x000000500000 : "kernel" [ 15.062860] 0x000000500000-0x000004000000 : "ubi" [ 15.124871] libphy: Fixed MDIO Bus: probed [ 15.174790] libphy: orion_mdio_bus: probed [ 15.224092] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 15.306832] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 15.411631] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 15.515965] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 15.594194] ehci-pci: EHCI PCI platform driver [ 15.647454] ehci-orion: EHCI orion driver [ 15.695599] orion-ehci f1050000.ehci: EHCI Host Controller [ 15.761387] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 15.853274] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 15.953980] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 16.026179] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 16.107484] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.194033] usb usb1: Product: EHCI Host Controller [ 16.252469] usb usb1: Manufacturer: Linux 4.12.8-kirkwood-tld-1 ehci_hcd [ 16.332771] usb usb1: SerialNumber: f1050000.ehci [ 16.389739] hub 1-0:1.0: USB hub found [ 16.434709] hub 1-0:1.0: 1 port detected [ 16.482246] usbcore: registered new interface driver usb-storage [ 16.554574] mousedev: PS/2 mouse device common for all mice [ 16.621980] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 16.704473] i2c /dev entries driver [ 16.747270] hidraw: raw HID events driver (C) Jiri Kosina [ 16.812376] drop_monitor: Initializing network drop monitor service [ 16.887823] NET: Registered protocol family 17 [ 16.941157] Key type dns_resolver registered [ 16.992336] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 17.073444] registered taskstats version 1 [ 17.122540] Loading compiled-in X.509 certificates [ 17.180152] zswap: loaded using pool lzo/zbud [ 17.234633] Key type big_key registered [ 17.282481] Key type encrypted registered [ 17.331849] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 17.433547] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 [ 17.514069] Waiting 1 sec before mounting root device... [ 17.577750] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 17.664174] hub 1-1:1.0: USB hub found [ 17.709167] hub 1-1:1.0: 2 ports detected [ 18.564600] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.655264] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 18.747084] VFS: Mounted root (ext3 filesystem) readonly on device 8:1. [ 18.828928] devtmpfs: mounted [ 18.867326] Freeing unused kernel memory: 1024K INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. ERROR: could not open /proc/stat: No such file or directory findfs: unable to resolve 'LABEL=rootfs' [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 30.841026] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean,[ 31.086767] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro 14460/196608 files, 198308/786432 blocks . ok [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files.... [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 33.512501] mv643xx_eth: no PHY [ 33.512538] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:90:0b:19:ee:25 Sending on LPF/eth0/00:90:0b:19:ee:25 Sending on Socket/fallback DHCPREQUEST of 192.168.1.128 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.128 from 192.168.1.1 bound to 192.168.1.128 -- renewal in 21124 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1176 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1179 (klogd) . ok [ ok ] Running local boot scripts (/etc/rc.local). y Debian GNU/Linux 9 debian ttyS0 debian login: Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Sat Mar 11 11:16:01 PST 2000 on ttyS0 Linux debian 4.12.8-kirkwood-tld-1 #1 PREEMPT Thu Aug 17 04:51:51 PDT 2017 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# root@debian:~# root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.313 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.225 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.213 ms ^C --- 192.168.1.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2088ms rtt min/avg/max/mdev = 0.213/0.250/0.313/0.046 ms root@debian:~# ifconfig -a eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.128 netmask 255.255.255.0 broadcast 192.168.1.255 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 56 bytes 4669 (4.5 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 22 bytes 2171 (2.1 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 36 eth1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:26 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 37 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 loop txqueuelen 1000 (Local Loopback) RX packets 3 bytes 169 (169.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3 bytes 169 (169.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@debian:~# modprobe mv88e6085 modprobe: ERROR: ../libkmod/libkmod.c:586 kmod_search_moddep() could not open moddep file '/lib/modules/4.12.8-kirkwood-tld-1/modules.dep.bin' modprobe: FATAL: Module mv88e6085 not found in directory /lib/modules/4.12.8-kirkwood-tld-1 root@debian:~#
Re: Debian on QiZhiTong 501mv2 August 19, 2017 04:38PM |
Admin Registered: 13 years ago Posts: 18,576 |
Re: Debian on QiZhiTong 501mv2 August 19, 2017 06:22PM |
Registered: 8 years ago Posts: 166 |
MB302>> pri bootdelay=5 baudrate=9600 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 run_diag=yes console=console=ttyS0,9600 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=mem=512M root=/dev/ram bootargs_end=:::DB88FXX81:eth0:none image_name=uImage boottitle1=QiZhiTong Bootup bootcmd2=ide reset; ext2load ide 0:c 0x2000000 /boot/uImage;setenv bootargs ro root=/dev/sda12 $(console) $(mvNetConfig) quiet;bootm 0x2000000 boottitle2=QiZhiTong Restore password=$1$F5w1D$nzHGehkXN8JlDdjraKy1n/ bootdefault=1 bootcmd=nand read.e 0x2800000 0x400000 0x700000; nand read.e 0x2000000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root) $(mvNetConfig);bootm 0x2000000 0x2800000 standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000; ethaddr=00:90:0b:19:ee:25 ethmtu=1500 eth1addr=00:90:0b:19:ee:26 eth1mtu=1500 mvNetConfig=mv_net_config=(00:90:0b:19:ee:26,0:1:2:3)(00:90:0b:19:ee:27,4),mtu=1500 usb0Mode=host nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 bootcmd1=setenv bootargs $(console);nand read.e $(loadaddr) 0x100000 0x400000;bootm $(loadaddr) ipaddr=192.168.1.200 serverip=192.168.1.3 bootcmd4=ide reset;ext2load ide 0:1 0x00800000 /boot/uImage;setenv bootargs rootdelay=1 root=/dev/sda1 console=ttyS0,9600;bootm 0x800000 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no enaAutoRecovery=no pcieTune=no Environment size: 1656/131068 bytes
Re: Debian on QiZhiTong 501mv2 August 19, 2017 06:32PM |
Admin Registered: 13 years ago Posts: 18,576 |
setenv bootcmd4 'ide reset; ext2load ide 0:1 0x00800000 /boot/uImage; ext2load ide 0:1 0x1100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=LABEL=rootfs console=ttyS0,9600 earlyprintk=serial; bootm 0x800000 0x1100000'
Re: Debian on QiZhiTong 501mv2 August 19, 2017 11:38PM |
Registered: 8 years ago Posts: 166 |
bootm: BOOTCMD4 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: JMicron Firm: 100415 Ser#: 00000000002E9 Type: Hard Disk Supports 48-bit addressing Capacity: 3836.0 MB = 3.7 GB (7856128 x 512) 3815077 bytes read 7680389 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.12.8-kirkwood-tld-1 Created: 2000-01-01 0:17:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3815013 Bytes = 3.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.12.8-kirkwood-tld-1 Created: 2000-01-01 0:18:00 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7680325 Bytes = 7.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.8-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 PREEMPT Thu Aug 17 04:51:51 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=10 root=LABEL=rootfs console=ttyS0,9600 earlyprintk=serial [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 498860K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 25428K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db32d4 ( 717 kB) [ 0.000000] .bss : 0xc0db9dac - 0xc0e01fc0 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.094908] Switching to timer-based delay loop, resolution 5ns [ 0.167347] Console: colour dummy device 80x30 [ 0.221599] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.348757] pid_max: default: 32768 minimum: 301 [ 0.405283] Security Framework initialized [ 0.455547] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.535837] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.622167] CPU: Testing write buffer coherency: ok [ 0.682543] Setting up static identity map for 0x100000 - 0x100058 [ 0.757847] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.823902] devtmpfs: initialized [ 0.868462] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.987306] futex hash table entries: 256 (order: -1, 3072 bytes) [ 1.061667] prandom: seed boundary self test passed [ 1.125325] prandom: 100 self tests passed [ 1.175365] pinctrl core: initialized pinctrl subsystem [ 1.240049] NET: Registered protocol family 16 [ 1.294751] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.379567] cpuidle: using governor ladder [ 1.429703] cpuidle: using governor menu [ 1.478165] Feroceon L2: Enabling L2 [ 1.522048] Feroceon L2: Cache support initialised. [ 1.581819] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 1.708022] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 1.838791] No ATAGs? [ 1.847671] vgaarb: loaded [ 1.909583] SCSI subsystem initialized [ 1.955960] usbcore: registered new interface driver usbfs [ 2.022788] usbcore: registered new interface driver hub [ 2.087561] usbcore: registered new device driver usb [ 2.150106] clocksource: Switched to clocksource orion_clocksource [ 2.314053] VFS: Disk quotas dquot_6.6.0 [ 2.362144] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.456935] NET: Registered protocol family 2 [ 2.510903] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 2.596477] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 2.674682] TCP: Hash tables configured (established 4096 bind 4096) [ 2.751893] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 2.822774] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 2.899058] NET: Registered protocol family 1 [ 2.952608] RPC: Registered named UNIX socket transport module. [ 3.024562] RPC: Registered udp transport module. [ 3.081935] RPC: Registered tcp transport module. [ 3.139296] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.217760] Unpacking initramfs... [ 3.259533] Initramfs unpacking failed: junk in compressed archive [ 3.355505] Freeing initrd memory: 7504K [ 3.403688] NetWinder Floating Point Emulator V0.97 (double precision) [ 3.483793] audit: initializing netlink subsys (disabled) [ 3.549919] Initialise system trusted keyrings [ 3.604188] audit: type=2000 audit(1.739:1): state=initialized audit_enabled=0 res=1 [ 3.698046] Key type blacklist registered [ 3.747241] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 3.825501] zbud: loaded [ 3.857822] NFS: Registering the id_resolver key type [ 3.919398] Key type id_resolver registered [ 3.970516] Key type id_legacy registered [ 4.019564] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 4.100901] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 4.178279] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 4.263991] fuse init (API version 7.26) [ 4.312424] orangefs_debugfs_init: called with debug mask: :none: :0: [ 4.390933] orangefs_init: module version upstream loaded [ 4.456611] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 6.300115] random: fast init done [ 10.531673] Key type asymmetric registered [ 10.581979] Asymmetric key parser 'x509' registered [ 10.641518] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 10.731289] io scheduler noop registered [ 10.779350] io scheduler deadline registered [ 10.831595] io scheduler cfq registered (default) [ 10.890140] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.975951] loop: module loaded [ 11.016180] libphy: Fixed MDIO Bus: probed [ 11.067048] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.146306] ehci-pci: EHCI PCI platform driver [ 11.200610] ehci-orion: EHCI orion driver [ 11.249802] usbcore: registered new interface driver usb-storage [ 11.323145] mousedev: PS/2 mouse device common for all mice [ 11.391252] i2c /dev entries driver [ 11.434475] kirkwood-cpufreq kirkwood-cpufreq: Unable to get cpuclk [ 11.510695] kirkwood-cpufreq: probe of kirkwood-cpufreq failed with error -22 [ 11.597585] hidraw: raw HID events driver (C) Jiri Kosina [ 11.663665] drop_monitor: Initializing network drop monitor service [ 11.740048] NET: Registered protocol family 17 [ 11.794345] Key type dns_resolver registered [ 11.847299] registered taskstats version 1 [ 11.897391] Loading compiled-in X.509 certificates [ 11.955864] zswap: loaded using pool lzo/zbud [ 12.011354] Key type big_key registered [ 12.060279] Key type encrypted registered [ 12.110681] hctosys: unable to open rtc device (rtc0) [ 16.528517] Unable to handle kernel paging request at virtual address e0000004 [ 16.616120] pgd = c0004000 [ 16.649554] [e0000004] *pgd=00000000 [ 16.693411] Internal error: Oops: 5 [#1] PREEMPT ARM [ 16.753923] Modules linked in: [ 16.791529] CPU: 0 PID: 1 Comm: swapper Not tainted 4.12.8-kirkwood-tld-1 #1 [ 16.877039] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 16.953182] task: df484020 task.stack: df486000 [ 17.008498] PC is at crc32_be+0xac/0x160 [ 17.056508] LR is at 0xe0000000 [ 17.095154] pc : [<c057dfa0>] lr : [<e0000000>] psr: 80000053 [ 17.095154] sp : df487ef0 ip : 00000007 fp : 00000000 [ 17.234830] r10: c0c4a838 r9 : c0c57544 r8 : 00000000 [ 17.298472] r7 : 00000000 r6 : 02a03bb1 r5 : bc652662 r4 : c115b238 [ 17.377738] r3 : c0950af0 r2 : b1f4b018 r1 : f0defde0 r0 : 0cbc7f85 [ 17.457005] Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none [ 17.544602] Control: 0005397f Table: 00004000 DAC: 00000053 [ 17.614493] Process swapper (pid: 1, stack limit = 0xdf486190) [ 17.685426] Stack: (0xdf487ef0 to 0xdf488000) [ 17.738656] 7ee0: c115b238 f0defde7 c0dfb790 c0c4a834 [ 17.837715] 7f00: 00000000 c0c3ef6c c0c3ef3c ffffe000 c0db9dc0 c0101824 c0a6bc2b c0132f70 [ 17.936770] 7f20: 00000000 c02981d0 60000053 c0aec06c 000000b8 00000007 00000007 c0aececc [ 18.035826] 7f40: 000000b7 c0aececc dfffce72 dfffce7e c0d0bbd8 00000007 000000b8 c0db9dc0 [ 18.134882] 7f60: 00000008 000000b8 c0db9dc0 c0c4a834 c0db9dc0 c0c00e8c 00000007 00000007 [ 18.233938] 7f80: 00000000 c0c005b0 00000000 c0829284 00000000 00000000 00000000 00000000 [ 18.332994] 7fa0: 00000000 c082928c 00000000 c0106f70 00000000 00000000 00000000 00000000 [ 18.432050] 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 18.531106] 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 9a1a1000 faeeda50 [ 18.630178] [<c057dfa0>] (crc32_be) from [<c0c3ef6c>] (of_fdt_raw_init+0x30/0x74) [ 18.720892] [<c0c3ef6c>] (of_fdt_raw_init) from [<c0101824>] (do_one_initcall+0x12c/0x158) [ 18.820988] [<c0101824>] (do_one_initcall) from [<c0c00e8c>] (kernel_init_freeable+0x208/0x250) [ 18.926296] [<c0c00e8c>] (kernel_init_freeable) from [<c082928c>] (kernel_init+0x8/0x108) [ 19.025352] [<c082928c>] (kernel_init) from [<c0106f70>] (ret_from_fork+0x14/0x24) [ 19.117112] Code: e0230420 1afffff7 ebff8684 e8bd81f0 (e59e6004) [ 19.191169] ---[ end trace a30bee26ee48793f ]--- [ 19.247745] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 19.247745] [ 19.359285] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 19.359285]
Re: Debian on QiZhiTong 501mv2 August 20, 2017 12:08AM |
Admin Registered: 13 years ago Posts: 18,576 |
setenv bootcmd4 'ide reset; ext2load ide 0:1 0x00800000 /boot/uImage; ext2load ide 0:1 0x02100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=LABEL=rootfs console=ttyS0,9600 earlyprintk=serial; bootm 0x800000 0x02100000'
Re: Debian on QiZhiTong 501mv2 August 20, 2017 12:49AM |
Registered: 8 years ago Posts: 166 |
bootm: BOOTCMD4 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: JMicron Firm: 100415 Ser#: 00000000002E9 Type: Hard Disk Supports 48-bit addressing Capacity: 3836.0 MB = 3.7 GB (7856128 x 512) 3815077 bytes read 7680389 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.12.8-kirkwood-tld-1 Created: 2000-01-01 0:17:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3815013 Bytes = 3.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-4.12.8-kirkwood-tld-1 Created: 2000-01-01 0:18:00 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7680325 Bytes = 7.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.8-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 PREEMPT Thu Aug 17 04:51:51 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=10 root=LABEL=rootfs console=ttyS0,9600 earlyprintk=serial [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 498848K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 25440K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db32d4 ( 717 kB) [ 0.000000] .bss : 0xc0db9dac - 0xc0e01fc0 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.094908] Switching to timer-based delay loop, resolution 5ns [ 0.167348] Console: colour dummy device 80x30 [ 0.221600] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.348758] pid_max: default: 32768 minimum: 301 [ 0.405285] Security Framework initialized [ 0.455547] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.535837] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.622174] CPU: Testing write buffer coherency: ok [ 0.682543] Setting up static identity map for 0x100000 - 0x100058 [ 0.757847] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.823900] devtmpfs: initialized [ 0.868441] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.987305] futex hash table entries: 256 (order: -1, 3072 bytes) [ 1.061667] prandom: seed boundary self test passed [ 1.125328] prandom: 100 self tests passed [ 1.175365] pinctrl core: initialized pinctrl subsystem [ 1.240044] NET: Registered protocol family 16 [ 1.294752] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.379572] cpuidle: using governor ladder [ 1.429703] cpuidle: using governor menu [ 1.478167] Feroceon L2: Enabling L2 [ 1.522048] Feroceon L2: Cache support initialised. [ 1.581819] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 1.708022] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 1.838792] No ATAGs? [ 1.847667] vgaarb: loaded [ 1.909582] SCSI subsystem initialized [ 1.955955] usbcore: registered new interface driver usbfs [ 2.022788] usbcore: registered new interface driver hub [ 2.087562] usbcore: registered new device driver usb [ 2.150106] clocksource: Switched to clocksource orion_clocksource [ 2.314007] VFS: Disk quotas dquot_6.6.0 [ 2.362145] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.456931] NET: Registered protocol family 2 [ 2.510902] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 2.596476] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 2.674681] TCP: Hash tables configured (established 4096 bind 4096) [ 2.751893] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 2.822774] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 2.899057] NET: Registered protocol family 1 [ 2.952606] RPC: Registered named UNIX socket transport module. [ 3.024562] RPC: Registered udp transport module. [ 3.081934] RPC: Registered tcp transport module. [ 3.139296] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.217759] Unpacking initramfs... [ 3.925441] Freeing initrd memory: 7504K [ 3.973621] NetWinder Floating Point Emulator V0.97 (double precision) [ 4.053796] audit: initializing netlink subsys (disabled) [ 4.120008] Initialise system trusted keyrings [ 4.174255] audit: type=2000 audit(2.309:1): state=initialized audit_enabled=0 res=1 [ 4.268116] Key type blacklist registered [ 4.317304] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 4.395567] zbud: loaded [ 4.427877] NFS: Registering the id_resolver key type [ 4.489465] Key type id_resolver registered [ 4.540585] Key type id_legacy registered [ 4.589632] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 4.670969] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 4.748347] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 4.834061] fuse init (API version 7.26) [ 4.882494] orangefs_debugfs_init: called with debug mask: :none: :0: [ 4.961009] orangefs_init: module version upstream loaded [ 5.026680] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 6.230114] random: fast init done [ 11.110415] Key type asymmetric registered [ 11.160612] Asymmetric key parser 'x509' registered [ 11.220172] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 11.309853] io scheduler noop registered [ 11.357855] io scheduler deadline registered [ 11.410096] io scheduler cfq registered (default) [ 11.468758] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 11.559167] mv_xor f1060800.xor: Marvell shared XOR driver [ 11.680874] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 11.772807] mv_xor f1060900.xor: Marvell shared XOR driver [ 11.900873] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 11.992979] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 12.071393] console [ttyS0] disabled [ 12.115267] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 12.223778] console [ttyS0] enabled [ 12.223778] console [ttyS0] enabled [ 12.308216] bootconsole [earlycon0] disabled [ 12.308216] bootconsole [earlycon0] disabled [ 12.419638] loop: module loaded [ 12.457778] sata_mv f1080000.sata: slots 32 ports 1 [ 12.517658] scsi host0: sata_mv [ 12.555518] ata1: SATA max UDMA/133 irq 32 [ 12.605141] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 12.681333] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 12.736608] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 12.824214] Scanning device for bad blocks [ 13.002439] Bad eraseblock 2455 at 0x00000265c000 [ 13.145034] 3 ofpart partitions found on MTD device orion_nand [ 13.214907] Creating 3 MTD partitions on "orion_nand": [ 13.276487] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 13.351780] ata1.00: ATA-7: JMicron, 100415, max UDMA/133 [ 13.351787] ata1.00: 7856128 sectors, multi 1: LBA48 [ 13.416775] ata1.00: configured for UDMA/133 [ 13.477728] scsi 0:0:0:0: Direct-Access ATA JMicron 15 PQ: 0 ANSI: 5 [ 13.479122] sd 0:0:0:0: [sda] 7856128 512-byte logical blocks: (4.02 GB/3.75 GiB) [ 13.479188] sd 0:0:0:0: [sda] Write Protect is off [ 13.479307] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 13.628985] sda: sda1 sda2 [ 13.630689] sd 0:0:0:0: [sda] Attached SCSI disk [ 13.976119] 0x000000000000-0x000000100000 : "u-boot" [ 14.036885] 0x000000100000-0x000000500000 : "kernel" [ 14.097764] 0x000000500000-0x000004000000 : "ubi" [ 14.159661] libphy: Fixed MDIO Bus: probed [ 14.209570] libphy: orion_mdio_bus: probed [ 14.258872] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 14.341640] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 14.446449] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 14.550778] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 14.629005] ehci-pci: EHCI PCI platform driver [ 14.682266] ehci-orion: EHCI orion driver [ 14.730410] orion-ehci f1050000.ehci: EHCI Host Controller [ 14.796195] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 14.888086] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 14.980144] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 15.052312] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 15.133648] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 15.220197] usb usb1: Product: EHCI Host Controller [ 15.278631] usb usb1: Manufacturer: Linux 4.12.8-kirkwood-tld-1 ehci_hcd [ 15.358936] usb usb1: SerialNumber: f1050000.ehci [ 15.415905] hub 1-0:1.0: USB hub found [ 15.460875] hub 1-0:1.0: 1 port detected [ 15.508420] usbcore: registered new interface driver usb-storage [ 15.580738] mousedev: PS/2 mouse device common for all mice [ 15.648143] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 15.730639] i2c /dev entries driver [ 15.773443] hidraw: raw HID events driver (C) Jiri Kosina [ 15.838530] drop_monitor: Initializing network drop monitor service [ 15.914069] NET: Registered protocol family 17 [ 15.967334] Key type dns_resolver registered [ 16.018503] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 16.099647] registered taskstats version 1 [ 16.148705] Loading compiled-in X.509 certificates [ 16.206236] zswap: loaded using pool lzo/zbud [ 16.267965] Key type big_key registered [ 16.323103] Key type encrypted registered [ 16.372455] rtc-mv f1010300.rtc: setting system clock to 2000-03-11 19:13:08 UTC (952801988) [ 16.474110] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 Loading, please wait... [ 16.557451] Freeing unused kernel memory: 1024K starting version 232 [ 16.740262] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.916995] hub 1-1:1.0: USB hub found [ 17.036876] hub 1-1:1.0: 2 ports detected [ 17.227875] mv88e6085 f1072004.mdio-bus-mii:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 17.356154] mvsdio f1090000.mvsdio: Got CD GPIO [ 17.911231] libphy: mv88e6xxx SMI: probed [ 17.959245] DSA: switch 0 0 parsed [ 17.999916] DSA: tree 0 parsed [ 19.015532] Marvell 88E1121R mv88e6xxx-0:00: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:00, irq=-1) [ 19.267870] Marvell 88E1121R mv88e6xxx-0:01: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:01, irq=-1) [ 19.522604] Marvell 88E1121R mv88e6xxx-0:02: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:02, irq=-1) [ 19.782606] Marvell 88E1121R mv88e6xxx-0:03: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:03, irq=-1) [ 20.042604] Marvell 88E1121R mv88e6xxx-0:04: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:04, irq=-1) Begin: Loading essential drivers ... done. [ 21.330174] random: crng init done Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done[ 30.406679] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem . Begin: Runnin[ 30.500701] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) g /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: clean, 34659/196608 files, 264025/786432 blocks done. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 32.616043] orion_wdt: Initial timeout 21 sec [ 32.787947] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 33.379386] marvell-cesa f1030000.crypto: CESA device successfully registered done. [ ok ] Activating swap:. [ 34.079257] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files.... [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 36.514224] mv643xx_eth: no PHY [ 36.514263] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:90:0b:19:ee:25 Sending on LPF/eth0/00:90:0b:19:ee:25 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 No DHCPOFFERS received. No working leases in persistent database - sleeping. 98.014860] NET: Registered protocol family 10 [ 98.087214] Segment Routing with IPv6 2done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. INIT: Entering runlevel: 2ry files... [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1297 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1301 (klogd) . ok [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Sat Mar 11 11:04:33 PST 2000 on ttyS0 Linux debian 4.12.8-kirkwood-tld-1 #1 PREEMPT Thu Aug 17 04:51:51 PDT 2017 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# ping 192.168.1.1 connect: Network is unreachable root@debian:~# ping 192.168.1.1 connect: Network is unreachable root@debian:~# ifconfig -a aux: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::290:bff:fe19:ee25 prefixlen 64 scopeid 0x20<link> ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 190 bytes 50742 (49.5 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 24 bytes 4344 (4.2 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 36 eth1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:26 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 37 lan1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan2: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 177 bytes 43422 (42.4 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan3: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan4: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 2 bytes 140 (140.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 2 bytes 140 (140.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@debian:~# ifconfig lan2 192.168.1.41 netmask 255.255.255.0 [ 156.457739] IPv6: ADDRCONF(NETDEV_UP): lan2: link is not ready root@debian:~# [ 157.587862] mv88e6085 f1072004.mdio-bus-mii:0a lan2: Link is Down [ 159.662246] mv88e6085 f1072004.mdio-bus-mii:0a lan2: Link is Up - 1Gbps/Full - flow control off [ 159.671037] IPv6: ADDRCONF(NETDEV_CHANGE): lan2: link becomes ready root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.627 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.236 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.264 ms ^C --- 192.168.1.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2052ms rtt min/avg/max/mdev = 0.236/0.375/0.627/0.179 msseems that the switch is working properly.
root@debian:~# ifconfig eth1 192.168.1.42 netmask 255.255.255.0 [ 222.678710] mv643xx_eth: no PHY [ 222.678749] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 10 Mb/s, half duplex, flow control disabled root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. From 192.168.1.42 icmp_seq=1 Destination Host Unreachable From 192.168.1.42 icmp_seq=2 Destination Host Unreachable From 192.168.1.42 icmp_seq=3 Destination Host Unreachable ^C --- 192.168.1.1 ping statistics --- 5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 4122ms pipe 4
Re: Debian on QiZhiTong 501mv2 August 20, 2017 01:46AM |
Admin Registered: 13 years ago Posts: 18,576 |
but the eth1(wan) working not properly(log after a reboot): root@debian:~# ifconfig eth1 192.168.1.42 netmask 255.255.255.0 [ 222.678710] mv643xx_eth: no PHY [ 222.678749] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 10 Mb/s, half duplex, flow control disabled
Re: Debian on QiZhiTong 501mv2 August 20, 2017 03:39AM |
Admin Registered: 13 years ago Posts: 18,576 |
--- kirkwood-qizhitong_501m_v2.dts 2017-08-20 00:01:46.071914874 -0700 +++ kirkwood-qizhitong_501m_v2.dts.update_2 2017-08-20 01:36:48.322023088 -0700 @@ -131,6 +131,10 @@ &mdio { status = "okay"; + ethphy1: ethernet-phy@1 { + reg = <1>; + }; + switch@10 { compatible = "marvell,mv88e6085"; #address-cells = <1>; @@ -189,8 +193,9 @@ }; ð1 { - status = "okay"; + status = "okay"; ethernet1-port@0 { + phy-handle = <ðphy1>; }; };
Re: Debian on QiZhiTong 501mv2 August 20, 2017 06:35AM |
Registered: 8 years ago Posts: 166 |
bootm: BOOTCMD4 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: JMicron Firm: 100415 Ser#: 00000000002E9 Type: Hard Disk Supports 48-bit addressing Capacity: 3836.0 MB = 3.7 GB (7856128 x 512) 3815176 bytes read 7680389 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.12.8-kirkwood-tld-1 Created: 2017-08-20 11:14:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3815112 Bytes = 3.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-4.12.8-kirkwood-tld-1 Created: 2000-01-01 0:18:00 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7680325 Bytes = 7.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.8-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 PREEMPT Thu Aug 17 04:51:51 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=10 root=LABEL=rootfs console=ttyS0,9600 earlyprintk=serial [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 498848K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 25440K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db32d4 ( 717 kB) [ 0.000000] .bss : 0xc0db9dac - 0xc0e01fc0 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.094908] Switching to timer-based delay loop, resolution 5ns [ 0.167344] Console: colour dummy device 80x30 [ 0.221599] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.348756] pid_max: default: 32768 minimum: 301 [ 0.405285] Security Framework initialized [ 0.455546] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.535836] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.622171] CPU: Testing write buffer coherency: ok [ 0.682543] Setting up static identity map for 0x100000 - 0x100058 [ 0.757847] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.823905] devtmpfs: initialized [ 0.868451] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.987307] futex hash table entries: 256 (order: -1, 3072 bytes) [ 1.061671] prandom: seed boundary self test passed [ 1.125322] prandom: 100 self tests passed [ 1.175365] pinctrl core: initialized pinctrl subsystem [ 1.240043] NET: Registered protocol family 16 [ 1.294751] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.379582] cpuidle: using governor ladder [ 1.429702] cpuidle: using governor menu [ 1.478153] Feroceon L2: Enabling L2 [ 1.522048] Feroceon L2: Cache support initialised. [ 1.581818] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 1.708023] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 1.838791] No ATAGs? [ 1.847668] vgaarb: loaded [ 1.909581] SCSI subsystem initialized [ 1.955957] usbcore: registered new interface driver usbfs [ 2.022788] usbcore: registered new interface driver hub [ 2.087562] usbcore: registered new device driver usb [ 2.150103] clocksource: Switched to clocksource orion_clocksource [ 2.313998] VFS: Disk quotas dquot_6.6.0 [ 2.362041] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.456839] NET: Registered protocol family 2 [ 2.510824] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 2.596372] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 2.674577] TCP: Hash tables configured (established 4096 bind 4096) [ 2.751789] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 2.822669] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 2.898950] NET: Registered protocol family 1 [ 2.952502] RPC: Registered named UNIX socket transport module. [ 3.024458] RPC: Registered udp transport module. [ 3.081830] RPC: Registered tcp transport module. [ 3.139192] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.217659] Unpacking initramfs... [ 3.925520] Freeing initrd memory: 7504K [ 3.973727] NetWinder Floating Point Emulator V0.97 (double precision) [ 4.053900] audit: initializing netlink subsys (disabled) [ 4.120147] Initialise system trusted keyrings [ 4.174454] audit: type=2000 audit(2.309:1): state=initialized audit_enabled=0 res=1 [ 4.268327] Key type blacklist registered [ 4.317511] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 4.395775] zbud: loaded [ 4.428093] NFS: Registering the id_resolver key type [ 4.489676] Key type id_resolver registered [ 4.540792] Key type id_legacy registered [ 4.589840] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 4.671177] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 4.748556] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 4.834271] fuse init (API version 7.26) [ 4.882692] orangefs_debugfs_init: called with debug mask: :none: :0: [ 4.961118] orangefs_init: module version upstream loaded [ 5.026785] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 6.210111] random: fast init done [ 11.110877] Key type asymmetric registered [ 11.161134] Asymmetric key parser 'x509' registered [ 11.220643] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 11.310370] io scheduler noop registered [ 11.358388] io scheduler deadline registered [ 11.410621] io scheduler cfq registered (default) [ 11.469312] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 11.559689] mv_xor f1060800.xor: Marvell shared XOR driver [ 11.680870] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 11.772803] mv_xor f1060900.xor: Marvell shared XOR driver [ 11.900876] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 11.992985] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 12.071391] console [ttyS0] disabled [ 12.115268] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 12.223778] console [ttyS0] enabled [ 12.223778] console [ttyS0] enabled [ 12.308216] bootconsole [earlycon0] disabled [ 12.308216] bootconsole [earlycon0] disabled [ 12.419667] loop: module loaded [ 12.457759] sata_mv f1080000.sata: slots 32 ports 1 [ 12.517663] scsi host0: sata_mv [ 12.555511] ata1: SATA max UDMA/133 irq 32 [ 12.605141] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 12.681332] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 12.736608] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 12.824223] Scanning device for bad blocks [ 13.002440] Bad eraseblock 2455 at 0x00000265c000 [ 13.144965] 3 ofpart partitions found on MTD device orion_nand [ 13.214803] Creating 3 MTD partitions on "orion_nand": [ 13.276384] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 13.351678] ata1.00: ATA-7: JMicron, 100415, max UDMA/133 [ 13.351685] ata1.00: 7856128 sectors, multi 1: LBA48 [ 13.416672] ata1.00: configured for UDMA/133 [ 13.477612] scsi 0:0:0:0: Direct-Access ATA JMicron 15 PQ: 0 ANSI: 5 [ 13.479003] sd 0:0:0:0: [sda] 7856128 512-byte logical blocks: (4.02 GB/3.75 GiB) [ 13.479068] sd 0:0:0:0: [sda] Write Protect is off [ 13.479187] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 13.628881] sda: sda1 sda2 [ 13.630633] sd 0:0:0:0: [sda] Attached SCSI disk [ 13.976016] 0x000000000000-0x000000100000 : "u-boot" [ 14.036783] 0x000000100000-0x000000500000 : "kernel" [ 14.097670] 0x000000500000-0x000004000000 : "ubi" [ 14.159562] libphy: Fixed MDIO Bus: probed [ 14.209451] libphy: orion_mdio_bus: probed [ 14.263242] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 14.346004] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 15.551719] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 15.656115] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 15.734351] ehci-pci: EHCI PCI platform driver [ 15.787611] ehci-orion: EHCI orion driver [ 15.835760] orion-ehci f1050000.ehci: EHCI Host Controller [ 15.901644] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 15.993548] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 16.090136] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 16.162345] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 16.243680] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.330230] usb usb1: Product: EHCI Host Controller [ 16.388663] usb usb1: Manufacturer: Linux 4.12.8-kirkwood-tld-1 ehci_hcd [ 16.468973] usb usb1: SerialNumber: f1050000.ehci [ 16.525959] hub 1-0:1.0: USB hub found [ 16.570909] hub 1-0:1.0: 1 port detected [ 16.618475] usbcore: registered new interface driver usb-storage [ 16.690764] mousedev: PS/2 mouse device common for all mice [ 16.758175] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 16.840675] i2c /dev entries driver [ 16.883477] hidraw: raw HID events driver (C) Jiri Kosina [ 16.948558] drop_monitor: Initializing network drop monitor service [ 17.024022] NET: Registered protocol family 17 [ 17.077352] Key type dns_resolver registered [ 17.128534] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 17.209678] registered taskstats version 1 [ 17.258739] Loading compiled-in X.509 certificates [ 17.316270] zswap: loaded using pool lzo/zbud [ 17.377926] Key type big_key registered [ 17.433117] Key type encrypted registered [ 17.482497] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 17.584197] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 Loading, please wait... [ 17.667544] Freeing unused kernel memory: 1024K starting version 232 [ 17.850257] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 18.026945] hub 1-1:1.0: USB hub found [ 18.147585] hub 1-1:1.0: 2 ports detected [ 18.350503] mv88e6085 f1072004.mdio-bus-mii:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 18.478328] mvsdio f1090000.mvsdio: Got CD GPIO [ 19.107069] libphy: mv88e6xxx SMI: probed [ 19.155110] DSA: switch 0 0 parsed [ 19.195782] DSA: tree 0 parsed [ 20.205539] Marvell 88E1121R mv88e6xxx-0:00: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:00, irq=-1) [ 20.455526] Marvell 88E1121R mv88e6xxx-0:01: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:01, irq=-1) [ 20.705520] Marvell 88E1121R mv88e6xxx-0:02: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:02, irq=-1) [ 20.957906] Marvell 88E1121R mv88e6xxx-0:03: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:03, irq=-1) [ 21.100175] random: crng init done [ 21.203199] Marvell 88E1121R mv88e6xxx-0:04: attached PHY driver [Marvell 88E1121R] (mii_bus:phy_addr=mv88e6xxx-0:04, irq=-1) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... do[ 31.602289] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem ne. Begin: Will[ 31.710666] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: recovering journal rootfs: clean, 34659/196608 files, 264028/786432 blocks done. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 33.794067] orion_wdt: Initial timeout 21 sec [ 34.107944] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 34.547440] marvell-cesa f1030000.crypto: CESA device successfully registered done. [ ok ] Activating swap:. [ 44.520751] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files.... [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 46.945923] mv643xx_eth: no PHY [ 46.945964] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:90:0b:19:ee:25 Sending on LPF/eth0/00:90:0b:19:ee:25 Sending on Socket/fallback DHCPREQUEST of 192.168.1.128 on eth0 to 255.255.255.255 port 67 [ 127.828800] NET: Registered protocol family 10 [ 127.885678] Segment Routing with IPv6 DHCPREQUEST of 192.168.1.128 on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 16 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 No DHCPOFFERS received. Trying recorded lease 192.168.1.128 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. done. NIT: Entering runlevel: 2mapper daemon: rpcbind [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1308 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1307 (klogd) . ok [ ok ] Running local boot scripts (/etc/rc.local). 7GDebian GNU/Linux 9 debian ttyS0 debian login: Debian GNU/Linux 9 debian ttyS0 debian login: Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Sat Mar 11 11:21:13 PST 2000 on ttyS0 Linux debian 4.12.8-kirkwood-tld-1 #1 PREEMPT Thu Aug 17 04:51:51 PDT 2017 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# ifconfig -a aux: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::290:bff:fe19:ee25 prefixlen 64 scopeid 0x20<link> ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 17 bytes 3964 (3.8 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 28 bytes 4772 (4.6 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 36 eth1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:26 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 37 lan1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan2: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan3: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan4: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 3 bytes 252 (252.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3 bytes 252 (252.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@debian:~# ifconfig -a aux: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::290:bff:fe19:ee25 prefixlen 64 scopeid 0x20<link> ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 17 bytes 3964 (3.8 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 29 bytes 4842 (4.7 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 36 eth1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:26 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 37 lan1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan2: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan3: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan4: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 3 bytes 252 (252.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3 bytes 252 (252.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@debian:~# ifconfig -a aux: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::290:bff:fe19:ee25 prefixlen 64 scopeid 0x20<link> ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 17 bytes 3964 (3.8 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 29 bytes 4842 (4.7 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 36 eth1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:26 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 37 lan1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan2: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan3: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan4: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 3 bytes 252 (252.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3 bytes 252 (252.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@debian:~# ifconfig eth1 192.168.1.43 netmask 255.255.255.0 [ 185.482243] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready root@debian:~# [ 187.900721] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 1000 Mb/s, full duplex, flow control disabled [ 187.910649] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready root@debian:~# root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.76 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.814 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.804 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.834 ms ^C --- 192.168.1.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3102ms rtt min/avg/max/mdev = 0.804/1.055/1.768/0.411 ms root@debian:~# ip addr del 192.168.1.43 dev eth1 Warning: Executing wildcard deletion to stay compatible with old scripts. Explicitly specify the prefix length (192.168.1.43/32) to avoid this warning. This special behaviour is likely to disappear in further releases, fix your scripts! root@debian:~# ip addr del 192.168.1.43/24 dev eth1 RTNETLINK answers: Cannot assign requested address root@debian:~# ifconfig -a aux: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::290:bff:fe19:ee25 prefixlen 64 scopeid 0x20<link> ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 17 bytes 3964 (3.8 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 32 bytes 5052 (4.9 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 36 eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::290:bff:fe19:ee26 prefixlen 64 scopeid 0x20<link> ether 00:90:0b:19:ee:26 txqueuelen 1000 (Ethernet) RX packets 353 bytes 26579 (25.9 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 61 bytes 8997 (8.7 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 37 lan1: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan2: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan3: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lan4: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 00:90:0b:19:ee:25 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 3 bytes 252 (252.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 3 bytes 252 (252.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@debian:~# [ 541.496758] mv643xx_eth_port mv643xx_eth_port.1 eth1: link down root@debian:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface root@debian:~# ifconfig lan1 192.168.1.43 netmask 255.255.255.0 [ 560.717524] IPv6: ADDRCONF(NETDEV_UP): lan1: link is not ready root@debian:~# [ 561.830243] mv88e6085 f1072004.mdio-bus-mii:0a lan1: Link is Down [ 563.902234] mv88e6085 f1072004.mdio-bus-mii:0a lan1: Link is Up - 1Gbps/Full - flow control off [ 563.911020] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready root@debian:~# root@debian:~# root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.40 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.801 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.867 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.816 ms 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=0.959 ms 64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=0.843 ms ^C --- 192.168.1.1 ping statistics --- 6 packets transmitted, 6 received, 0% packet loss, time 5103ms rtt min/avg/max/mdev = 0.801/0.947/1.401/0.212 ms root@debian:~# ip addr del 192.168.1.43/24 dev lan1 root@debian:~# [ 599.267888] mv88e6085 f1072004.mdio-bus-mii:0a lan1: Link is Down root@debian:~# root@debian:~# root@debian:~# ifconfig lan2 192.168.1.43 netmask 255.255.255.0 [ 607.987479] IPv6: ADDRCONF(NETDEV_UP): lan2: link is not ready root@debian:~# [ 609.110243] mv88e6085 f1072004.mdio-bus-mii:0a lan2: Link is Down [ 611.189282] mv88e6085 f1072004.mdio-bus-mii:0a lan2: Link is Up - 1Gbps/Full - flow control off [ 611.198071] IPv6: ADDRCONF(NETDEV_CHANGE): lan2: link becomes ready root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.820 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.828 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.818 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.865 ms ^C --- 192.168.1.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3042ms rtt min/avg/max/mdev = 0.818/0.832/0.865/0.040 ms root@debian:~# ip addr del 192.168.1.43/24 dev lan2 root@debian:~# [ 628.870239] mv88e6085 f1072004.mdio-bus-mii:0a lan2: Link is Down root@debian:~# ifconfig lan3 192.168.1.43 netmask 255.255.255.0 [ 641.997624] IPv6: ADDRCONF(NETDEV_UP): lan3: link is not ready root@debian:~# [ 643.108395] mv88e6085 f1072004.mdio-bus-mii:0a lan3: Link is Down [ 645.182737] mv88e6085 f1072004.mdio-bus-mii:0a lan3: Link is Up - 1Gbps/Full - flow control off [ 645.191525] IPv6: ADDRCONF(NETDEV_CHANGE): lan3: link becomes ready root@debian:~# root@debian:~# root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.68 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.830 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.825 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.819 ms ^C --- 192.168.1.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3092ms rtt min/avg/max/mdev = 0.819/1.039/1.683/0.372 ms root@debian:~# ip addr del 192.168.1.43/24 dev lan3 root@debian:~# [ 664.950740] mv88e6085 f1072004.mdio-bus-mii:0a lan3: Link is Down root@debian:~# ifconfig lan4 192.168.1.43 netmask 255.255.255.0 [ 674.207557] IPv6: ADDRCONF(NETDEV_UP): lan4: link is not ready root@debian:~# [ 675.270211] mv88e6085 f1072004.mdio-bus-mii:0a lan4: Link is Down [ 677.342199] mv88e6085 f1072004.mdio-bus-mii:0a lan4: Link is Up - 1Gbps/Full - flow control off [ 677.350990] IPv6: ADDRCONF(NETDEV_CHANGE): lan4: link becomes ready root@debian:~# root@debian:~# root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.67 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.831 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.821 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.828 ms ^C --- 192.168.1.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3062ms rtt min/avg/max/mdev = 0.821/1.038/1.673/0.367 ms root@debian:~# ip addr del 192.168.1.43/24 dev lan4 root@debian:~# [ 697.110246] mv88e6085 f1072004.mdio-bus-mii:0a lan4: Link is Down root@debian:~# root@debian:~# ifconfig aux 192.168.1.43 netmask 255.255.255.0 [ 708.077606] IPv6: ADDRCONF(NETDEV_UP): aux: link is not ready root@debian:~# [ 709.187888] mv88e6085 f1072004.mdio-bus-mii:0a aux: Link is Down [ 711.264579] mv88e6085 f1072004.mdio-bus-mii:0a aux: Link is Up - 1Gbps/Full - flow control off [ 711.273281] IPv6: ADDRCONF(NETDEV_CHANGE): aux: link becomes ready root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.752 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.829 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.826 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.821 ms 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=0.828 ms ^C --- 192.168.1.1 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4122ms rtt min/avg/max/mdev = 0.752/0.811/0.829/0.034 ms root@debian:~# [ 797.590219] mv88e6085 f1072004.mdio-bus-mii:0a aux: Link is Down [ 833.984571] mv88e6085 f1072004.mdio-bus-mii:0a aux: Link is Up - 100Mbps/Full - flow control rx/tx root@debian:~# root@debian:~# root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.995 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.447 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.861 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.870 ms 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=0.697 ms ^C --- 192.168.1.1 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4082ms rtt min/avg/max/mdev = 0.447/0.774/0.995/0.188 ms root@debian:~# [ 850.630229] mv88e6085 f1072004.mdio-bus-mii:0a aux: Link is Down root@debian:~# root@debian:~# ip addr del 192.168.1.43/24 dev aux root@debian:~# ifconfig eth1 192.168.1.43 netmask 255.255.255.0 root@debian:~# [ 891.781435] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 100 Mb/s, full duplex, flow control disabled root@debian:~# root@debian:~# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.38 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.848 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.432 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.844 ms 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=0.845 ms ^C --- 192.168.1.1 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4062ms rtt min/avg/max/mdev = 0.432/0.869/1.380/0.303 ms root@debian:~# ip addr del 192.168.1.43/24 dev eth1 root@debian:~# root@debian:~# root@debian:~# [ 925.109400] mv643xx_eth_port mv643xx_eth_port.1 eth1: link down
Re: Debian on QiZhiTong 501mv2 August 20, 2017 04:07PM |
Admin Registered: 13 years ago Posts: 18,576 |
Re: Debian on QiZhiTong 501mv2 September 04, 2017 10:34AM |
Registered: 8 years ago Posts: 166 |
/* Device tree file for the QiZhiTong 501M V2 box. * * Copyright (c) 2015-2017 bodhi <mibodhi@gmail.com> * wacke <cao88yu@gmail.com> * * Based on * Marvell RD88F6181 A Board descrition * Andrew Lunn <andrew@lunn.ch> */ /dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "QiZhiTong 501M V2"; compatible = "qizhitong,501m_v2","marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; chosen { bootargs = "console=ttyS0,9600n8 earlyprintk"; }; ocp@f1000000 { pinctrl: pin-controller@10000 { pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { marvell,pins = "mpp28"; marvell,function = "gpio"; }; }; serial@12000 { status = "okay"; }; sata@80000 { status = "okay"; nr-ports = <1>; }; mvsdio@90000 { pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; pinctrl-names = "default"; status = "okay"; cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; /* No WP GPIO */ }; }; dsa { status = "disabled"; compatible = "marvell,dsa"; #address-cells = <2>; #size-cells = <0>; dsa,ethernet = <ð0port>; dsa,mii-bus = <&mdio>; switch@10,0 { #address-cells = <1>; #size-cells = <0>; reg = <10 0>; /* MDIO address 16, switch 0 in tree */ port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; }; }; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "kernel"; reg = <0x0100000 0x400000>; }; partition@500000 { label = "ubi"; reg = <0x0500000 0x3b00000>; }; }; &mdio { status = "okay"; ethphy1: ethernet-phy@1 { reg = <1>; }; switch@10{ compatible = "marvell,mv88e6085"; #address-cells = <1>; #size-cells = <0>; reg = <10>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <ð0port>; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; &pciec { status = "okay"; }; &pcie0 { status = "okay"; }; ð0 { status = "okay"; ethernet0-port@0 { speed = <1000>; duplex = <1>; }; }; ð1 { status = "okay"; ethernet1-port@0 { phy-handle = <ðphy1>; }; };
Re: Debian on QiZhiTong 501mv2 September 04, 2017 05:59PM |
Admin Registered: 13 years ago Posts: 18,576 |