Re: Debian on QiZhiTong 501mv2 August 04, 2017 05:58AM |
Admin Registered: 13 years ago Posts: 18,550 |
&mdio { status = "okay"; switch@0 { compatible = "marvell,mv88e6085"; #address-cells = <1>; #size-cells = <0>; reg = <0>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "wan"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <ð0port>; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; ð0 { status = "okay"; ethernet0-port@0 { speed = <1000>; duplex = <1>; }; };
Re: Debian on QiZhiTong 501mv2 August 04, 2017 10:00AM |
Registered: 8 years ago Posts: 166 |
/* * Marvell RD88F6181 A Board descrition * * Andrew Lunn <andrew@lunn.ch> * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. * * This file contains the definitions for the board with the A0 or * higher stepping of the SoC. The ethernet switch does not have a * "wan" port. */ /dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "QiZhiTong 501M V2"; compatible = "qizhitong,501m_v2","marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; chosen { bootargs = "console=ttyS0,9600n8 earlyprintk"; }; mbus { pcie-controller { status = "okay"; pcie@1,0 { status = "okay"; }; }; }; ocp@f1000000 { pinctrl: pin-controller@10000 { pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { marvell,pins = "mpp28"; marvell,function = "gpio"; }; }; serial@12000 { status = "okay"; }; sata@80000 { status = "okay"; nr-ports = <1>; }; mvsdio@90000 { pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; pinctrl-names = "default"; status = "okay"; cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; /* No WP GPIO */ }; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "kernel"; reg = <0x0100000 0x400000>; }; partition@500000 { label = "ubi"; reg = <0x0500000 0x3b00000>; }; }; &mdio { status = "okay"; switch@0 { compatible = "marvell,mv88e6161"; #address-cells = <1>; #size-cells = <0>; reg = <10>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <ð0port>; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; ð0 { status = "okay"; ethernet0-port@0 { }; }; ð1 { status = "okay"; ethernet1-port@0 { }; };
bootm: BOOTCMD2 SD found. Card desciption is: Manufacturer: 0x1b, OEM "SM" Product name: "00000", revision 1.0 Serial number: 460975022 Manufacturing date: 7/2010 CRC: 0x00, b0 = 0 3911705 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.11.3-kirkwood-tld-2 Created: 2017-08-04 14:45:30 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3911641 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.3-kirkwood-tld-2 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Tue Jun 6 17:01:17 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=1 root=/ noinitrd console=ttyS0,9600 rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506316K/524288K available (8192K kernel code, 786K rwdata, 2016K rodata, 1024K init, 280K bss, 17972K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0dc49b4 ( 787 kB) [ 0.000000] .bss : 0xc0dc49b4 - 0xc0e0acc8 ( 281 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000451] Console: colour dummy device 80x30 [ 0.000484] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090104] pid_max: default: 32768 minimum: 301 [ 0.090313] Security Framework initialized [ 0.090434] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090453] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091302] CPU: Testing write buffer coherency: ok [ 0.092299] Setting up static identity map for 0x100000 - 0x100058 [ 0.092530] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.096012] devtmpfs: initialized [ 0.100007] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100032] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.100379] prandom: seed boundary self test passed [ 0.104129] prandom: 100 self tests passed [ 0.104141] pinctrl core: initialized pinctrl subsystem [ 0.105327] NET: Registered protocol family 16 [ 0.106170] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.107698] cpuidle: using governor ladder [ 0.107759] cpuidle: using governor menu [ 0.108176] Feroceon L2: Enabling L2 [ 0.108217] Feroceon L2: Cache support initialised. [ 0.108551] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.108655] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.113393] No ATAGs? [ 0.122175] vgaarb: loaded [ 0.122494] SCSI subsystem initialized [ 0.122966] usbcore: registered new interface driver usbfs [ 0.123040] usbcore: registered new interface driver hub [ 0.123126] usbcore: registered new device driver usb [ 0.124198] clocksource: Switched to clocksource orion_clocksource [ 0.216431] VFS: Disk quotas dquot_6.6.0 [ 0.216511] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.227173] NET: Registered protocol family 2 [ 0.227943] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.228020] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.228088] TCP: Hash tables configured (established 4096 bind 4096) [ 0.228247] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.228288] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.228508] NET: Registered protocol family 1 [ 0.228952] RPC: Registered named UNIX socket transport module. [ 0.228965] RPC: Registered udp transport module. [ 0.228972] RPC: Registered tcp transport module. [ 0.228979] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.229387] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.230291] audit: initializing netlink subsys (disabled) [ 0.230735] Initialise system trusted keyrings [ 0.230865] audit: type=2000 audit(0.220:1): state=initialized audit_enabled=0 res=1 [ 0.230936] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.231024] zbud: loaded [ 0.232017] NFS: Registering the id_resolver key type [ 0.232045] Key type id_resolver registered [ 0.232053] Key type id_legacy registered [ 0.232071] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.232080] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.232581] Key type cifs.spnego registered [ 0.232601] Key type cifs.idmap registered [ 0.232613] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.232873] fuse init (API version 7.26) [ 0.233259] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.233530] orangefs_init: module version upstream loaded [ 0.233542] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.554205] random: fast init done [ 4.342571] Key type asymmetric registered [ 4.342586] Asymmetric key parser 'x509' registered [ 4.342654] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 4.342665] io scheduler noop registered [ 4.342673] io scheduler deadline registered [ 4.342746] io scheduler cfq registered (default) [ 4.343978] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 4.345863] mv_xor f1060800.xor: Marvell shared XOR driver [ 4.404989] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 4.405224] mv_xor f1060900.xor: Marvell shared XOR driver [ 4.464989] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 4.465443] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 4.466632] console [ttyS0] disabled [ 4.466692] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 11.588788] console [ttyS0] enabled [ 11.641190] loop: module loaded [ 11.679290] sata_mv f1080000.sata: slots 32 ports 1 [ 11.739625] scsi host0: sata_mv [ 11.777447] ata1: SATA max UDMA/133 irq 32 [ 11.827135] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 11.903269] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 11.958541] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 12.046146] Scanning device for bad blocks [ 12.225643] ata1: SATA link down (SStatus 0 SControl F300) [ 12.291931] Bad eraseblock 2455 at 0x00000265c000 [ 12.435424] 3 ofpart partitions found on MTD device orion_nand [ 12.435429] Creating 3 MTD partitions on "orion_nand": [ 12.435445] 0x000000000000-0x000000100000 : "u-boot" [ 12.436718] 0x000000100000-0x000000500000 : "kernel" [ 12.438121] 0x000000500000-0x000004000000 : "ubi" [ 12.443449] libphy: Fixed MDIO Bus: probed [ 12.444418] libphy: orion_mdio_bus: probed [ 12.444697] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 12.446216] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 12.446866] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 12.446997] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.447020] ehci-pci: EHCI PCI platform driver [ 12.447086] ehci-orion: EHCI orion driver [ 12.447255] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.447287] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.447470] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 12.517397] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.517664] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.517673] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.517679] usb usb1: Product: EHCI Host Controller [ 12.517685] usb usb1: Manufacturer: Linux 4.11.3-kirkwood-tld-2 ehci_hcd [ 12.517690] usb usb1: SerialNumber: f1050000.ehci [ 12.518403] hub 1-0:1.0: USB hub found [ 12.518450] hub 1-0:1.0: 1 port detected [ 12.519302] mousedev: PS/2 mouse device common for all mice [ 12.519826] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 12.519947] i2c /dev entries driver [ 12.520858] hidraw: raw HID events driver (C) Jiri Kosina [ 12.582778] drop_monitor: Initializing network drop monitor service [ 12.583017] NET: Registered protocol family 17 [ 12.583192] Key type dns_resolver registered [ 12.583967] registered taskstats version 1 [ 12.583974] Loading compiled-in X.509 certificates [ 12.584031] zswap: loaded using pool lzo/zbud [ 12.586942] Key type big_key registered [ 12.588762] Key type encrypted registered [ 12.590095] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 12.945577] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 13.634215] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 [ 13.634223] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 13.716154] hub 1-1:1.0: USB hub found [ 13.802728] hub 1-1:1.0: 2 ports detected [ 15.218300] Waiting 1 sec before mounting root device... [ 16.324251] Waiting for root device /...
Re: Debian on QiZhiTong 501mv2 August 04, 2017 07:31PM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Debian on QiZhiTong 501mv2 August 06, 2017 07:27AM |
Registered: 8 years ago Posts: 166 |
bootm: BOOTCMD2 SD found. Card desciption is: Manufacturer: 0x1b, OEM "SM" Product name: "00000", revision 1.0 Serial number: 460975022 Manufacturing date: 7/2010 CRC: 0x00, b0 = 0 3911729 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.11.3-kirkwood-tld-2 Created: 2017-08-06 12:12:15 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3911665 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.3-kirkwood-tld-2 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Tue Jun 6 17:01:17 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=1 root=/ noinitrd console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506316K/524288K available (8192K kernel code, 786K rwdata, 2016K rodata, 1024K init, 280K bss, 17972K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0dc49b4 ( 787 kB) [ 0.000000] .bss : 0xc0dc49b4 - 0xc0e0acc8 ( 281 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000452] Console: colour dummy device 80x30 [ 0.000486] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090105] pid_max: default: 32768 minimum: 301 [ 0.090312] Security Framework initialized [ 0.090435] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090452] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091308] CPU: Testing write buffer coherency: ok [ 0.092304] Setting up static identity map for 0x100000 - 0x100058 [ 0.092535] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.095998] devtmpfs: initialized [ 0.099962] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.099987] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.100343] prandom: seed boundary self test passed [ 0.104094] prandom: 100 self tests passed [ 0.104106] pinctrl core: initialized pinctrl subsystem [ 0.105294] NET: Registered protocol family 16 [ 0.106114] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.107652] cpuidle: using governor ladder [ 0.107716] cpuidle: using governor menu [ 0.108108] Feroceon L2: Enabling L2 [ 0.108150] Feroceon L2: Cache support initialised. [ 0.108484] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.108588] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.113320] No ATAGs? [ 0.122080] vgaarb: loaded [ 0.122397] SCSI subsystem initialized [ 0.122870] usbcore: registered new interface driver usbfs [ 0.122943] usbcore: registered new interface driver hub [ 0.123029] usbcore: registered new device driver usb [ 0.124079] clocksource: Switched to clocksource orion_clocksource [ 0.216299] VFS: Disk quotas dquot_6.6.0 [ 0.216379] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.227038] NET: Registered protocol family 2 [ 0.227812] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.227888] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.227956] TCP: Hash tables configured (established 4096 bind 4096) [ 0.228123] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.228163] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.228382] NET: Registered protocol family 1 [ 0.228824] RPC: Registered named UNIX socket transport module. [ 0.228836] RPC: Registered udp transport module. [ 0.228844] RPC: Registered tcp transport module. [ 0.228851] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.229236] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.230142] audit: initializing netlink subsys (disabled) [ 0.230590] Initialise system trusted keyrings [ 0.230721] audit: type=2000 audit(0.220:1): state=initialized audit_enabled=0 res=1 [ 0.230791] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.230882] zbud: loaded [ 0.231883] NFS: Registering the id_resolver key type [ 0.231911] Key type id_resolver registered [ 0.231920] Key type id_legacy registered [ 0.231937] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.231947] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.232447] Key type cifs.spnego registered [ 0.232467] Key type cifs.idmap registered [ 0.232480] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.232739] fuse init (API version 7.26) [ 0.233123] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.233393] orangefs_init: module version upstream loaded [ 0.233404] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.554086] random: fast init done [ 4.342499] Key type asymmetric registered [ 4.342513] Asymmetric key parser 'x509' registered [ 4.342579] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 4.342591] io scheduler noop registered [ 4.342599] io scheduler deadline registered [ 4.342671] io scheduler cfq registered (default) [ 4.343905] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 4.345791] mv_xor f1060800.xor: Marvell shared XOR driver [ 4.404871] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 4.405105] mv_xor f1060900.xor: Marvell shared XOR driver [ 4.464869] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 4.465322] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 4.466521] console [ttyS0] disabled [ 4.466582] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 11.579226] console [ttyS0] enabled [ 11.631622] loop: module loaded [ 11.669721] sata_mv f1080000.sata: slots 32 ports 1 [ 11.730071] scsi host0: sata_mv [ 11.767883] ata1: SATA max UDMA/133 irq 32 [ 11.817576] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 11.893705] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 11.948978] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 12.036583] Scanning device for bad blocks [ 12.215523] ata1: SATA link down (SStatus 0 SControl F300) [ 12.282405] Bad eraseblock 2455 at 0x00000265c000 [ 12.425931] 3 ofpart partitions found on MTD device orion_nand [ 12.425936] Creating 3 MTD partitions on "orion_nand": [ 12.425953] 0x000000000000-0x000000100000 : "u-boot" [ 12.427227] 0x000000100000-0x000000500000 : "kernel" [ 12.428632] 0x000000500000-0x000004000000 : "ubi" [ 12.433946] libphy: Fixed MDIO Bus: probed [ 12.434901] libphy: orion_mdio_bus: probed [ 12.435174] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 12.436688] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 12.437340] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 12.437471] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.437493] ehci-pci: EHCI PCI platform driver [ 12.437559] ehci-orion: EHCI orion driver [ 12.437731] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.437762] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.437951] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 12.507936] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.508202] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.508210] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.508216] usb usb1: Product: EHCI Host Controller [ 12.508222] usb usb1: Manufacturer: Linux 4.11.3-kirkwood-tld-2 ehci_hcd [ 12.508228] usb usb1: SerialNumber: f1050000.ehci [ 12.508936] hub 1-0:1.0: USB hub found [ 12.508985] hub 1-0:1.0: 1 port detected [ 12.509835] mousedev: PS/2 mouse device common for all mice [ 12.510360] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 12.510480] i2c /dev entries driver [ 12.511383] hidraw: raw HID events driver (C) Jiri Kosina [ 12.511700] drop_monitor: Initializing network drop monitor service [ 12.511939] NET: Registered protocol family 17 [ 12.512112] Key type dns_resolver registered [ 12.512869] registered taskstats version 1 [ 12.512876] Loading compiled-in X.509 certificates [ 12.512932] zswap: loaded using pool lzo/zbud [ 12.515853] Key type big_key registered [ 12.517676] Key type encrypted registered [ 12.519002] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 12.936119] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 13.624636] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 [ 13.624644] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 13.706600] hub 1-1:1.0: USB hub found [ 13.793166] hub 1-1:1.0: 2 ports detected [ 15.208743] Waiting 1 sec before mounting root device...
Re: Debian on QiZhiTong 501mv2 August 06, 2017 08:18PM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Debian on QiZhiTong 501mv2 August 06, 2017 09:42PM |
Registered: 8 years ago Posts: 166 |
Re: Debian on QiZhiTong 501mv2 August 07, 2017 01:20AM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Debian on QiZhiTong 501mv2 August 07, 2017 10:05AM |
Registered: 8 years ago Posts: 166 |
/* * Marvell RD88F6181 A Board descrition * * Andrew Lunn <andrew@lunn.ch> * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. * * This file contains the definitions for the board with the A0 or * higher stepping of the SoC. The ethernet switch does not have a * "wan" port. */ /dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "QiZhiTong 501M V2"; compatible = "qizhitong,501m_v2","marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; chosen { bootargs = "console=ttyS0,9600n8 earlyprintk"; }; mbus { pcie-controller { status = "okay"; pcie@1,0 { status = "okay"; }; }; }; ocp@f1000000 { pinctrl: pin-controller@10000 { pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { marvell,pins = "mpp28"; marvell,function = "gpio"; }; }; serial@12000 { status = "okay"; }; sata@80000 { status = "okay"; nr-ports = <1>; }; mvsdio@90000 { pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; pinctrl-names = "default"; status = "okay"; cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; /* No WP GPIO */ }; }; mvsw61xx { compatible = "marvell,88e6161"; status = "okay"; reg = <0x10>; is-indirect; mii-bus = <&mdio>; ethernet = <ð1port>; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "kernel"; reg = <0x0100000 0x400000>; }; partition@500000 { label = "ubi"; reg = <0x0500000 0x3b00000>; }; }; &mdio { status = "okay"; switch@0 { compatible = "marvell,mv88e6085"; #address-cells = <1>; #size-cells = <0>; reg = <10 0>; status = "okay"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <ð1port>; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; ð0 { status = "okay"; ethernet0-port@0 { }; }; ð1 { status = "okay"; ethernet1-port@0 { }; };
bootm: BOOTCMD2 SD found. Card desciption is: Manufacturer: 0x1b, OEM "SM" Product name: "00000", revision 1.0 Serial number: 460975022 Manufacturing date: 7/2010 CRC: 0x00, b0 = 0 3911909 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.11.3-kirkwood-tld-2 Created: 2017-08-07 14:57:47 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3911845 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.11.3-kirkwood-tld-2 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Tue Jun 6 17:01:17 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=1 root=/ noinitrd console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506316K/524288K available (8192K kernel code, 786K rwdata, 2016K rodata, 1024K init, 280K bss, 17972K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0dc49b4 ( 787 kB) [ 0.000000] .bss : 0xc0dc49b4 - 0xc0e0acc8 ( 281 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000447] Console: colour dummy device 80x30 [ 0.000480] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090105] pid_max: default: 32768 minimum: 301 [ 0.090312] Security Framework initialized [ 0.090433] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090451] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091299] CPU: Testing write buffer coherency: ok [ 0.092293] Setting up static identity map for 0x100000 - 0x100058 [ 0.092524] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.096022] devtmpfs: initialized [ 0.100042] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100119] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.100419] prandom: seed boundary self test passed [ 0.104169] prandom: 100 self tests passed [ 0.104181] pinctrl core: initialized pinctrl subsystem [ 0.105383] NET: Registered protocol family 16 [ 0.106200] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.107708] cpuidle: using governor ladder [ 0.107770] cpuidle: using governor menu [ 0.108166] Feroceon L2: Enabling L2 [ 0.108208] Feroceon L2: Cache support initialised. [ 0.108543] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.108647] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.113501] No ATAGs? [ 0.122317] vgaarb: loaded [ 0.122642] SCSI subsystem initialized [ 0.123104] usbcore: registered new interface driver usbfs [ 0.123179] usbcore: registered new interface driver hub [ 0.123267] usbcore: registered new device driver usb [ 0.124318] clocksource: Switched to clocksource orion_clocksource [ 0.216376] VFS: Disk quotas dquot_6.6.0 [ 0.216453] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.227125] NET: Registered protocol family 2 [ 0.227894] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.227971] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.228038] TCP: Hash tables configured (established 4096 bind 4096) [ 0.228216] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.228246] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.228462] NET: Registered protocol family 1 [ 0.228909] RPC: Registered named UNIX socket transport module. [ 0.228921] RPC: Registered udp transport module. [ 0.228928] RPC: Registered tcp transport module. [ 0.228935] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.229320] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.230243] audit: initializing netlink subsys (disabled) [ 0.230698] Initialise system trusted keyrings [ 0.230842] audit: type=2000 audit(0.220:1): state=initialized audit_enabled=0 res=1 [ 0.230913] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.231001] zbud: loaded [ 0.231991] NFS: Registering the id_resolver key type [ 0.232015] Key type id_resolver registered [ 0.232024] Key type id_legacy registered [ 0.232041] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.232050] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.232548] Key type cifs.spnego registered [ 0.232568] Key type cifs.idmap registered [ 0.232581] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.232842] fuse init (API version 7.26) [ 0.233220] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.233494] orangefs_init: module version upstream loaded [ 0.233506] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.554326] random: fast init done [ 4.342914] Key type asymmetric registered [ 4.342930] Asymmetric key parser 'x509' registered [ 4.342997] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 4.343008] io scheduler noop registered [ 4.343017] io scheduler deadline registered [ 4.343091] io scheduler cfq registered (default) [ 4.344434] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 4.346222] mv_xor f1060800.xor: Marvell shared XOR driver [ 4.405113] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 4.405340] mv_xor f1060900.xor: Marvell shared XOR driver [ 4.465108] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 4.465560] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 4.466769] console [ttyS0] disabled [ 4.466830] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 11.579540] console [ttyS0] enabled [ 11.631945] loop: module loaded [ 11.670049] sata_mv f1080000.sata: slots 32 ports 1 [ 11.730341] scsi host0: sata_mv [ 11.768208] ata1: SATA max UDMA/133 irq 32 [ 11.817883] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 11.894019] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 11.949292] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 12.036898] Scanning device for bad blocks [ 12.215764] ata1: SATA link down (SStatus 0 SControl F300) [ 12.282668] Bad eraseblock 2455 at 0x00000265c000 [ 12.426171] 3 ofpart partitions found on MTD device orion_nand [ 12.426176] Creating 3 MTD partitions on "orion_nand": [ 12.426192] 0x000000000000-0x000000100000 : "u-boot" [ 12.427467] 0x000000100000-0x000000500000 : "kernel" [ 12.428881] 0x000000500000-0x000004000000 : "ubi" [ 12.434193] libphy: Fixed MDIO Bus: probed [ 12.435165] libphy: orion_mdio_bus: probed [ 12.685720] mv88e6085 f1072004.mdio-bus-mii:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 12.981131] libphy: mv88e6xxx SMI: probed [ 13.029846] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 13.112843] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 13.217916] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 13.322283] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 13.400470] ehci-pci: EHCI PCI platform driver [ 13.453739] ehci-orion: EHCI orion driver [ 13.501863] orion-ehci f1050000.ehci: EHCI Host Controller [ 13.567553] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 13.659479] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 13.754352] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 13.826474] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 13.907818] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 13.994372] usb usb1: Product: EHCI Host Controller [ 14.052803] usb usb1: Manufacturer: Linux 4.11.3-kirkwood-tld-2 ehci_hcd [ 14.133107] usb usb1: SerialNumber: f1050000.ehci [ 14.190112] hub 1-0:1.0: USB hub found [ 14.235044] hub 1-0:1.0: 1 port detected [ 14.282780] mousedev: PS/2 mouse device common for all mice [ 14.350114] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 14.432719] i2c /dev entries driver [ 14.475409] hidraw: raw HID events driver (C) Jiri Kosina [ 14.540492] drop_monitor: Initializing network drop monitor service [ 14.616029] NET: Registered protocol family 17 [ 14.669454] Key type dns_resolver registered [ 14.720597] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 14.801708] registered taskstats version 1 [ 14.850801] Loading compiled-in X.509 certificates [ 14.908330] zswap: loaded using pool lzo/zbud [ 14.963149] Key type big_key registered [ 15.011122] Key type encrypted registered [ 15.060657] mv88e6085 f1072004.mdio-bus-mii:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 15.168637] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 [ 15.249040] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 15.335530] hub 1-1:1.0: USB hub found [ 15.380620] hub 1-1:1.0: 2 ports detected [ 15.460890] libphy: mv88e6xxx SMI: probed [ 15.508940] DSA: switch 0 0 parsed [ 15.549792] DSA: tree 0 parsed [ 15.732097] mv88e6085 f1072004.mdio-bus-mii:0a lan1: no phy at 0 [ 15.804063] mv88e6085 f1072004.mdio-bus-mii:0a lan1: failed to connect to port 0: -19 [ 15.897895] mv643xx_eth_port mv643xx_eth_port.1 eth1: error -19 setting up slave phy [ 16.014376] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 0: -19 [ 16.100448] mv88e6085 f1072004.mdio-bus-mii:0a lan2: no phy at 1 [ 16.172395] mv88e6085 f1072004.mdio-bus-mii:0a lan2: failed to connect to port 1: -19 [ 16.266226] mv643xx_eth_port mv643xx_eth_port.1 eth1: error -19 setting up slave phy [ 16.384372] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 1: -19 [ 16.470380] mv88e6085 f1072004.mdio-bus-mii:0a lan3: no phy at 2 [ 16.542368] mv88e6085 f1072004.mdio-bus-mii:0a lan3: failed to connect to port 2: -19 [ 16.636202] mv643xx_eth_port mv643xx_eth_port.1 eth1: error -19 setting up slave phy [ 16.754371] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 2: -19 [ 16.840454] mv88e6085 f1072004.mdio-bus-mii:0a lan4: no phy at 3 [ 16.912448] mv88e6085 f1072004.mdio-bus-mii:0a lan4: failed to connect to port 3: -19 [ 17.006283] mv643xx_eth_port mv643xx_eth_port.1 eth1: error -19 setting up slave phy [ 17.124380] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 3: -19 [ 17.210432] mv88e6085 f1072004.mdio-bus-mii:0a aux: no phy at 4 [ 17.281381] mv88e6085 f1072004.mdio-bus-mii:0a aux: failed to connect to port 4: -19 [ 17.374176] mv643xx_eth_port mv643xx_eth_port.1 eth1: error -19 setting up slave phy [ 17.494372] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 4: -19 [ 17.583333] rtc-mv f1010300.rtc: setting system clock to 2000-02-13 11:41:26 UTC (950442086) [ 17.684835] Waiting 1 sec before mounting root device...
Re: Debian on QiZhiTong 501mv2 August 11, 2017 07:54PM |
Admin Registered: 13 years ago Posts: 18,550 |
compatible = "marvell,mv88e6161";
/dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "QiZhiTong 501M V2"; compatible = "qizhitong,501m_v2","marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; chosen { bootargs = "console=ttyS0,9600n8 earlyprintk"; }; mbus { pcie-controller { status = "okay"; pcie@1,0 { status = "okay"; }; }; }; ocp@f1000000 { pinctrl: pin-controller@10000 { pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { marvell,pins = "mpp28"; marvell,function = "gpio"; }; }; serial@12000 { status = "okay"; }; sata@80000 { status = "okay"; nr-ports = <1>; }; mvsdio@90000 { pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; pinctrl-names = "default"; status = "okay"; cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; /* No WP GPIO */ }; }; dsa { status = "disabled"; compatible = "marvell,dsa"; #address-cells = <2>; #size-cells = <0>; dsa,ethernet = <ð0port>; dsa,mii-bus = <&mdio>; switch@10,0 { #address-cells = <1>; #size-cells = <0>; reg = <10 0>; /* MDIO address 16, switch 0 in tree */ port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; }; }; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "kernel"; reg = <0x0100000 0x400000>; }; partition@500000 { label = "ubi"; reg = <0x0500000 0x3b00000>; }; }; &mdio { status = "okay"; switch@0 { compatible = "marvell,mv88e6161"; #address-cells = <1>; #size-cells = <0>; reg = <10>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <ð0port>; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; ð0 { status = "okay"; ethernet0-port@0 { speed = <1000>; duplex = <1>; }; }; ð1 { status = "okay"; ethernet1-port@0 { }; };
Re: Debian on QiZhiTong 501mv2 August 12, 2017 08:28AM |
Registered: 8 years ago Posts: 166 |
Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=1 root=/ noinitrd console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506352K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 17936K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000038] Switching to timer-based delay loop, resolution 5ns [ 0.000473] Console: colour dummy device 80x30 [ 0.000506] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000527] pid_max: default: 32768 minimum: 301 [ 0.000734] Security Framework initialized [ 0.000858] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000876] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001711] CPU: Testing write buffer coherency: ok [ 0.002717] Setting up static identity map for 0x100000 - 0x100058 [ 0.002950] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.006027] devtmpfs: initialized [ 0.009892] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.009916] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.010343] prandom: seed boundary self test passed [ 0.014093] prandom: 100 self tests passed [ 0.014104] pinctrl core: initialized pinctrl subsystem [ 0.015253] NET: Registered protocol family 16 [ 0.016078] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017581] cpuidle: using governor ladder [ 0.017647] cpuidle: using governor menu [ 0.018039] Feroceon L2: Enabling L2 [ 0.018081] Feroceon L2: Cache support initialised. [ 0.018424] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.018529] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.023168] No ATAGs? [ 0.032047] vgaarb: loaded [ 0.032367] SCSI subsystem initialized [ 0.032845] usbcore: registered new interface driver usbfs [ 0.032920] usbcore: registered new interface driver hub [ 0.033006] usbcore: registered new device driver usb [ 0.034097] clocksource: Switched to clocksource orion_clocksource [ 0.126894] VFS: Disk quotas dquot_6.6.0 [ 0.126976] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.137677] NET: Registered protocol family 2 [ 0.138460] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.138537] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.138600] TCP: Hash tables configured (established 4096 bind 4096) [ 0.138769] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.138798] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.139013] NET: Registered protocol family 1 [ 0.139450] RPC: Registered named UNIX socket transport module. [ 0.139463] RPC: Registered udp transport module. [ 0.139471] RPC: Registered tcp transport module. [ 0.139478] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.139820] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.140733] audit: initializing netlink subsys (disabled) [ 0.141188] Initialise system trusted keyrings [ 0.141240] Key type blacklist registered [ 0.141349] audit: type=2000 audit(0.136:1): state=initialized audit_enabled=0 res=1 [ 0.141438] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.141503] zbud: loaded [ 0.142523] NFS: Registering the id_resolver key type [ 0.142551] Key type id_resolver registered [ 0.142560] Key type id_legacy registered [ 0.142577] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.142587] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.142805] jffs2: version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc. [ 0.142996] fuse init (API version 7.26) [ 0.143381] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.143644] orangefs_init: module version upstream loaded [ 0.143655] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.554106] random: fast init done [ 6.015876] Key type asymmetric registered [ 6.015891] Asymmetric key parser 'x509' registered [ 6.015962] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.015974] io scheduler noop registered [ 6.015982] io scheduler deadline registered [ 6.016057] io scheduler cfq registered (default) [ 6.017324] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.019057] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.074886] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.075130] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.134884] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.135320] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.136553] console [ttyS0] disabled [ 6.136617] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 13.256499] console [ttyS0] enabled [ 13.308890] loop: module loaded [ 13.347072] sata_mv f1080000.sata: slots 32 ports 1 [ 13.407357] scsi host0: sata_mv [ 13.445162] ata1: SATA max UDMA/133 irq 32 [ 13.494808] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 13.570975] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 13.626246] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 13.713849] Scanning device for bad blocks [ 13.892396] Bad eraseblock 2455 at 0x00000265c000 [ 13.948741] ata1: SATA link down (SStatus 0 SControl F300) [ 14.100706] 3 ofpart partitions found on MTD device orion_nand [ 14.170585] Creating 3 MTD partitions on "orion_nand": [ 14.232153] 0x000000000000-0x000000100000 : "u-boot" [ 14.292910] 0x000000100000-0x000000500000 : "kernel" [ 14.353777] 0x000000500000-0x000004000000 : "ubi" [ 14.415604] libphy: Fixed MDIO Bus: probed [ 14.465454] libphy: orion_mdio_bus: probed [ 14.514824] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 14.597754] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 14.702698] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 14.807033] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 14.885248] ehci-pci: EHCI PCI platform driver [ 14.938516] ehci-orion: EHCI orion driver [ 14.986654] orion-ehci f1050000.ehci: EHCI Host Controller [ 15.052454] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 15.144449] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 15.244131] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 15.316264] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 15.397600] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 15.484148] usb usb1: Product: EHCI Host Controller [ 15.542581] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 15.622887] usb usb1: SerialNumber: f1050000.ehci [ 15.679871] hub 1-0:1.0: USB hub found [ 15.724829] hub 1-0:1.0: 1 port detected [ 15.772339] usbcore: registered new interface driver usb-storage [ 15.844701] mousedev: PS/2 mouse device common for all mice [ 15.912087] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 15.994587] i2c /dev entries driver [ 16.037373] hidraw: raw HID events driver (C) Jiri Kosina [ 16.102519] drop_monitor: Initializing network drop monitor service [ 16.178029] NET: Registered protocol family 17 [ 16.231273] Key type dns_resolver registered [ 16.282455] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 16.363562] registered taskstats version 1 [ 16.412657] Loading compiled-in X.509 certificates [ 16.470194] zswap: loaded using pool lzo/zbud [ 16.525718] Key type big_key registered [ 16.573704] Key type encrypted registered [ 16.623048] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 16.724721] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 [ 16.805214] Waiting 1 sec before mounting root device... [ 16.868916] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.955151] hub 1-1:1.0: USB hub found [ 17.000214] hub 1-1:1.0: 2 ports detected
Re: Debian on QiZhiTong 501mv2 August 12, 2017 04:48PM |
Admin Registered: 13 years ago Posts: 18,550 |
14.415604] libphy: Fixed MDIO Bus: probed [ 14.465454] libphy: orion_mdio_bus: probed [ 14.514824] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 14.597754] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 14.702698] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26
&mdio { status = "okay"; switch@10 { compatible = "marvell,mv88e6085"; #address-cells = <1>; #size-cells = <0>; reg = <16>;
[ 7.580854] libphy: Fixed MDIO Bus: probed [ 7.585779] libphy: orion_mdio_bus: probed [ 7.590170] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 7.598122] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address ....... [ 8.363296] mv88e6085 f1072004.mdio-bus-mii:10: switch 0x171 detected: Marvell 88E6171, revision 2
Re: Debian on QiZhiTong 501mv2 August 12, 2017 05:06PM |
Admin Registered: 13 years ago Posts: 18,550 |
static const struct of_device_id mv88e6xxx_of_match[] = { { .compatible = "marvell,mv88e6085", .data = &mv88e6xxx_table[MV88E6085], }, { .compatible = "marvell,mv88e6190", .data = &mv88e6xxx_table[MV88E6190], }, { /* sentinel */ }, };
MODULE_DEVICE_TABLE(of, mv88e6xxx_of_match); static struct mdio_driver mv88e6xxx_driver = { .probe = mv88e6xxx_probe, .remove = mv88e6xxx_remove, .mdiodrv.driver = { .name = "mv88e6085", .of_match_table = mv88e6xxx_of_match, }, }; static int __init mv88e6xxx_init(void) { register_switch_driver(&mv88e6xxx_switch_drv); return mdio_driver_register(&mv88e6xxx_driver); } module_init(mv88e6xxx_init); static void __exit mv88e6xxx_cleanup(void) { mdio_driver_unregister(&mv88e6xxx_driver); unregister_switch_driver(&mv88e6xxx_switch_drv); } module_exit(mv88e6xxx_cleanup);
/dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "QiZhiTong 501M V2"; compatible = "qizhitong,501m_v2","marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; chosen { bootargs = "console=ttyS0,9600n8 earlyprintk"; }; mbus { pcie-controller { status = "okay"; pcie@1,0 { status = "okay"; }; }; }; ocp@f1000000 { pinctrl: pin-controller@10000 { pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { marvell,pins = "mpp28"; marvell,function = "gpio"; }; }; serial@12000 { status = "okay"; }; sata@80000 { status = "okay"; nr-ports = <1>; }; mvsdio@90000 { pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; pinctrl-names = "default"; status = "okay"; cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; /* No WP GPIO */ }; }; dsa { status = "disabled"; compatible = "marvell,dsa"; #address-cells = <2>; #size-cells = <0>; dsa,ethernet = <ð0port>; dsa,mii-bus = <&mdio>; switch@10,0 { #address-cells = <1>; #size-cells = <0>; reg = <10 0>; /* MDIO address 16, switch 0 in tree */ port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; }; }; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "kernel"; reg = <0x0100000 0x400000>; }; partition@500000 { label = "ubi"; reg = <0x0500000 0x3b00000>; }; }; &mdio { status = "okay"; switch@0 { compatible = "marvell,mv88e6085"; #address-cells = <1>; #size-cells = <0>; reg = <10>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <ð0port>; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; ð0 { status = "okay"; ethernet0-port@0 { speed = <1000>; duplex = <1>; }; }; ð1 { status = "okay"; ethernet1-port@0 { }; };
Re: Debian on QiZhiTong 501mv2 August 13, 2017 08:10AM |
Registered: 8 years ago Posts: 166 |
Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=1 root=/ initrd=/boot/uInitrd console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506352K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 17936K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000037] Switching to timer-based delay loop, resolution 5ns [ 0.000471] Console: colour dummy device 80x30 [ 0.000504] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000526] pid_max: default: 32768 minimum: 301 [ 0.000733] Security Framework initialized [ 0.000857] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000874] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001718] CPU: Testing write buffer coherency: ok [ 0.002725] Setting up static identity map for 0x100000 - 0x100058 [ 0.002957] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.006064] devtmpfs: initialized [ 0.009926] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.009951] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.010380] prandom: seed boundary self test passed [ 0.014131] prandom: 100 self tests passed [ 0.014142] pinctrl core: initialized pinctrl subsystem [ 0.015289] NET: Registered protocol family 16 [ 0.016112] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017627] cpuidle: using governor ladder [ 0.017690] cpuidle: using governor menu [ 0.018080] Feroceon L2: Enabling L2 [ 0.018122] Feroceon L2: Cache support initialised. [ 0.018466] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.018571] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.023204] No ATAGs? [ 0.032096] vgaarb: loaded [ 0.032417] SCSI subsystem initialized [ 0.032887] usbcore: registered new interface driver usbfs [ 0.032963] usbcore: registered new interface driver hub [ 0.033050] usbcore: registered new device driver usb [ 0.034143] clocksource: Switched to clocksource orion_clocksource [ 0.126942] VFS: Disk quotas dquot_6.6.0 [ 0.127023] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.137720] NET: Registered protocol family 2 [ 0.138507] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.138584] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.138648] TCP: Hash tables configured (established 4096 bind 4096) [ 0.138818] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.138847] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.139058] NET: Registered protocol family 1 [ 0.139498] RPC: Registered named UNIX socket transport module. [ 0.139510] RPC: Registered udp transport module. [ 0.139517] RPC: Registered tcp transport module. [ 0.139525] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.139863] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.140773] audit: initializing netlink subsys (disabled) [ 0.141236] Initialise system trusted keyrings [ 0.141289] Key type blacklist registered [ 0.141394] audit: type=2000 audit(0.136:1): state=initialized audit_enabled=0 res=1 [ 0.141481] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.141545] zbud: loaded [ 0.142567] NFS: Registering the id_resolver key type [ 0.142596] Key type id_resolver registered [ 0.142604] Key type id_legacy registered [ 0.142621] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.142631] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.142851] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.143041] fuse init (API version 7.26) [ 0.143429] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.143692] orangefs_init: module version upstream loaded [ 0.143703] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.554153] random: fast init done [ 6.015937] Key type asymmetric registered [ 6.015953] Asymmetric key parser 'x509' registered [ 6.016022] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.016034] io scheduler noop registered [ 6.016042] io scheduler deadline registered [ 6.016115] io scheduler cfq registered (default) [ 6.017388] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.019127] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.074933] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.075178] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.134927] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.135365] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.136595] console [ttyS0] disabled [ 6.136658] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 13.269052] console [ttyS0] enabled [ 13.321461] loop: module loaded [ 13.359603] sata_mv f1080000.sata: slots 32 ports 1 [ 13.419888] scsi host0: sata_mv [ 13.457697] ata1: SATA max UDMA/133 irq 32 [ 13.507347] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 13.583508] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 13.638781] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 13.726382] Scanning device for bad blocks [ 13.904945] Bad eraseblock 2455 at 0x00000265c000 [ 13.961276] ata1: SATA link down (SStatus 0 SControl F300) [ 14.113221] 3 ofpart partitions found on MTD device orion_nand [ 14.183119] Creating 3 MTD partitions on "orion_nand": [ 14.244687] 0x000000000000-0x000000100000 : "u-boot" [ 14.305446] 0x000000100000-0x000000500000 : "kernel" [ 14.366314] 0x000000500000-0x000004000000 : "ubi" [ 14.428126] libphy: Fixed MDIO Bus: probed [ 14.477993] libphy: orion_mdio_bus: probed [ 14.527358] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 14.610281] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 14.715231] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 14.819562] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 14.897783] ehci-pci: EHCI PCI platform driver [ 14.951050] ehci-orion: EHCI orion driver [ 14.999190] orion-ehci f1050000.ehci: EHCI Host Controller [ 15.064987] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 15.156967] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 15.254177] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 15.326404] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 15.407738] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 15.494286] usb usb1: Product: EHCI Host Controller [ 15.552719] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 15.633025] usb usb1: SerialNumber: f1050000.ehci [ 15.690006] hub 1-0:1.0: USB hub found [ 15.734967] hub 1-0:1.0: 1 port detected [ 15.782478] usbcore: registered new interface driver usb-storage [ 15.854840] mousedev: PS/2 mouse device common for all mice [ 15.922206] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 16.004752] i2c /dev entries driver [ 16.047597] hidraw: raw HID events driver (C) Jiri Kosina [ 16.112760] drop_monitor: Initializing network drop monitor service [ 16.188276] NET: Registered protocol family 17 [ 16.241621] Key type dns_resolver registered [ 16.292799] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 16.373901] registered taskstats version 1 [ 16.423006] Loading compiled-in X.509 certificates [ 16.480538] zswap: loaded using pool lzo/zbud [ 16.536059] Key type big_key registered [ 16.584060] Key type encrypted registered [ 16.633388] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 16.735114] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 [ 16.815617] Waiting 1 sec before mounting root device... [ 16.879258] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.965541] hub 1-1:1.0: USB hub found [ 17.010606] hub 1-1:1.0: 2 ports detectedStill did not found the switch....
Re: Debian on QiZhiTong 501mv2 August 13, 2017 06:42PM |
Admin Registered: 13 years ago Posts: 18,550 |
Quote
- the management port (cpu) is connected to eth0 with no PHY.
- In this box, eth1 is for the separate connection (it is not connected to the switch). So we leave it active.
Re: Debian on QiZhiTong 501mv2 August 13, 2017 11:17PM |
Registered: 8 years ago Posts: 166 |
this is corect,the eth1 is connected to a 88e1116 chip.Quote
- In this box, eth1 is for the separate connection (it is not connected to the switch). So we leave it active.
i'm not sure about this...Quote
- the management port (cpu) is connected to eth0 with no PHY.
Re: Debian on QiZhiTong 501mv2 August 14, 2017 12:35AM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Debian on QiZhiTong 501mv2 August 14, 2017 12:59AM |
Registered: 8 years ago Posts: 166 |
Re: Debian on QiZhiTong 501mv2 August 14, 2017 01:13AM |
Admin Registered: 13 years ago Posts: 18,550 |
compatible = "marvell, mv88e6190";
port@5 { reg = <5>; label = "cpu"; ethernet = <ð0port>; fixed-link { speed = <1000>; full-duplex; }; };
Re: Debian on QiZhiTong 501mv2 August 14, 2017 09:17AM |
Registered: 8 years ago Posts: 166 |
> compatible = "marvell, mv88e6190"; >
> port@5 { > reg = <5>; > label = "cpu"; > ethernet = <ð0port>; > fixed-link { > speed = <1000>; > full-duplex; > }; > }; >
/* * Marvell RD88F6181 A Board descrition * * Andrew Lunn <andrew@lunn.ch> * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. * * This file contains the definitions for the board with the A0 or * higher stepping of the SoC. The ethernet switch does not have a * "wan" port. */ /dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "QiZhiTong 501M V2"; compatible = "qizhitong,501m_v2","marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; chosen { bootargs = "console=ttyS0,9600n8 earlyprintk"; }; mbus { pcie-controller { status = "okay"; pcie@1,0 { status = "okay"; }; }; }; ocp@f1000000 { pinctrl: pin-controller@10000 { pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { marvell,pins = "mpp28"; marvell,function = "gpio"; }; }; serial@12000 { status = "okay"; }; sata@80000 { status = "okay"; nr-ports = <1>; }; mvsdio@90000 { pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; pinctrl-names = "default"; status = "okay"; cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; /* No WP GPIO */ }; }; dsa@0 { compatible = "marvell,dsa"; #address-cells = <2>; #size-cells = <0>; interrupts = <10>; dsa,ethernet = <ð0port>; dsa,mii-bus = <&mdio>; switch@0 { #address-cells = <1>; #size-cells = <0>; status = "okay"; reg = <10 0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; }; }; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "kernel"; reg = <0x0100000 0x400000>; }; partition@500000 { label = "ubi"; reg = <0x0500000 0x3b00000>; }; }; &mdio { status = "okay"; ethphy0: ethernet-phy@0 { device_type = "ethernet-phy"; reg = <1>; }; }; ð0 { status = "okay"; ethernet0-port@0 { speed = <1000>; duplex = <1>; }; }; ð1 { status = "okay"; ethernet1-port@0 { }; };
Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.74 (Wacke@HOME-Server) (gcc version 7.1.0 (LEDE GCC 7.1.0 r4235-61eb18d3f7) ) #0 Thu Jul 27 10:12:21 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512132K/524288K available (4807K kernel code, 276K rwdata, 1968K rodata, 248K init, 225K bss, 12156K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc06a5e44 (6776 kB) [ 0.000000] .init : 0xc06a6000 - 0xc06e4000 ( 248 kB) [ 0.000000] .data : 0xc06e4000 - 0xc07293c0 ( 277 kB) [ 0.000000] .bss : 0xc07293c0 - 0xc07618b0 ( 226 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000082] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090088] pid_max: default: 32768 minimum: 301 [ 0.090222] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090242] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090977] CPU: Testing write buffer coherency: ok [ 0.091400] Setting up static identity map for 0x81e0 - 0x821c [ 0.091667] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.096680] VFP support v0.3: not present [ 0.096924] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.096960] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.097143] pinctrl core: initialized pinctrl subsystem [ 0.098388] NET: Registered protocol family 16 [ 0.099137] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.103266] cpuidle: using governor ladder [ 0.103608] Feroceon L2: Enabling L2 [ 0.103649] Feroceon L2: Cache support initialised. [ 0.103927] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.104032] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.108424] No ATAGs? [ 0.126917] SCSI subsystem initialized [ 0.127919] usbcore: registered new interface driver usbfs [ 0.128012] usbcore: registered new interface driver hub [ 0.128088] usbcore: registered new device driver usb [ 0.129172] clocksource: Switched to clocksource orion_clocksource [ 0.146395] NET: Registered protocol family 2 [ 0.147129] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.147204] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.147274] TCP: Hash tables configured (established 4096 bind 4096) [ 0.147414] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.147444] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.147668] NET: Registered protocol family 1 [ 0.152512] Crashlog allocated RAM at address 0x3f00000 [ 0.168461] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.168516] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.175621] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.175642] io scheduler noop registered [ 0.175656] io scheduler deadline registered (default) [ 0.177099] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.177802] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated [ 0.178229] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated [ 0.178859] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 0.178877] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.178890] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.178903] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.179263] PCI: bus0: Fast back to back transfers disabled [ 0.179279] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.179422] PCI: bus1: Fast back to back transfers enabled [ 0.179470] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.221181] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.222333] console [ttyS0] disabled [ 0.222405] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 5.947199] console [ttyS0] enabled [ 5.990238] sata_mv f1080000.sata: slots 32 ports 1 [ 6.051274] scsi host0: sata_mv [ 6.089321] ata1: SATA max UDMA/133 irq 32 [ 6.138885] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 6.214993] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 6.270291] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 6.357904] Scanning device for bad blocks [ 6.537937] Bad eraseblock 2455 at 0x00000265c000 [ 6.681715] 3 ofpart partitions found on MTD device orion_nand [ 6.751614] Creating 3 MTD partitions on "orion_nand": [ 6.813179] 0x000000000000-0x000000100000 : "u-boot" [ 6.874515] 0x000000100000-0x000000500000 : "kernel" [ 6.935403] 0x000000500000-0x000004000000 : "ubi" [ 6.995174] libphy: orion_mdio_bus: probed [ 7.045301] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 7.128034] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 7.232982] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 7.337278] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.415437] ehci-pci: EHCI PCI platform driver [ 7.468734] ehci-orion: EHCI orion driver [ 7.516954] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.582635] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.674528] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 7.759204] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.831901] hub 1-0:1.0: USB hub found [ 7.876849] ata1: SATA link down (SStatus 0 SControl F300) [ 7.942790] hub 1-0:1.0: 1 port detected [ 7.990301] usbcore: registered new interface driver usb-storage [ 8.062801] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 8.145263] i2c /dev entries driver [ 8.187951] orion_wdt: Initial timeout 21 sec [ 8.241159] mvsdio f1090000.mvsdio: Got CD GPIO [ 8.334541] marvell-cesa f1030000.crypto: CESA device successfully registered [ 8.421333] NET: Registered protocol family 10 [ 8.476689] NET: Registered protocol family 17 [ 8.530053] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 8.681344] Distributed Switch Architecture driver version 0.1 [ 8.751891] mv643xx_eth_port mv643xx_eth_port.0 eth0: [0]: detected a Marvell 88E6161 (A1) switch [ 8.858293] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 9.080331] hub 1-1:1.0: USB hub found [ 9.125459] hub 1-1:1.0: 2 ports detected [ 9.188125] libphy: dsa slave smi: probed [ 9.247017] 8021q: 802.1Q VLAN Support v1.8 [ 9.300926] Key type encrypted registered [ 9.349529] UBI: auto-attach mtd2 [ 9.387113] ubi0: attaching mtd2 [ 9.744812] ubi0: scanning is finished [ 9.801795] ubi0: attached mtd2 (name "ubi", size 59 MiB) [ 9.866444] ubi0: PEB size: 16384 bytes (16 KiB), LEB size: 15872 bytes [ 9.945681] ubi0: min./max. I/O unit sizes: 512/512, sub-page size 256 [ 10.023908] ubi0: VID header offset: 256 (aligned 256), data offset: 512 [ 10.104211] ubi0: good PEBs: 3775, bad PEBs: 1, corrupted PEBs: 0 [ 10.177230] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 92 [ 10.262756] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1830178591 [ 10.372219] ubi0: available PEBs: 0, total reserved PEBs: 3775, PEBs reserved for bad PEB handling: 79 [ 10.484414] ubi0: background thread "ubi_bgt0d" started, PID 950 [ 10.557159] block ubiblock0_0: created from ubi0:0(rootfs) [ 10.622846] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 10.706527] rtc-mv f1010300.rtc: setting system clock to 2000-02-28 15:47:15 UTC (951752835) [ 10.813734] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 10.899991] Freeing unused kernel memory: 248K (c06a6000 - c06e4000) [ 11.571501] init: Console is alive [ 11.612417] init: - watchdog - [ 11.688474] init: - preinit - [ 12.229058] random: jshn: uninitialized urandom read (4 bytes read, 37 bits of entropy available) [ 12.403805] random: jshn: uninitialized urandom read (4 bytes read, 37 bits of entropy available) [ 12.535021] random: jshn: uninitialized urandom read (4 bytes read, 37 bits of entropy available) [ 12.668258] random: jshn: uninitialized urandom read (4 bytes read, 37 bits of entropy available) [ 12.797944] random: jshn: uninitialized urandom read (4 bytes read, 37 bits of entropy available) RTNETLINK answers: Network is down sendto(): Network unreachable Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 15.172270] mount_root: loading kmods from internal overlay [ 15.245100] mount_root: failed to launch kmodloader from internal overlay [ 15.709362] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 1019 [ 15.796166] UBIFS (ubi0:1): recovery needed [ 15.875499] random: procd: uninitialized urandom read (4 bytes read, 42 bits of entropy available) [ 16.014003] UBIFS (ubi0:1): recovery completed [ 16.067265] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 16.161134] UBIFS (ubi0:1): LEB size: 15872 bytes (15 KiB), min./max. I/O unit sizes: 512 bytes/512 bytes [ 16.275807] UBIFS (ubi0:1): FS size: 18824192 bytes (17 MiB, 1186 LEBs), journal size 936448 bytes (0 MiB, 59 LEBs) [ 16.400897] UBIFS (ubi0:1): reserved for root: 889112 bytes (868 KiB) [ 16.478080] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID B8615344-E6AD-4B1A-AB04-06EA22F30C5E, small LPT model [ 16.613827] UBIFS (ubi0:1): full atime support is enabled. [ 16.681937] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 16.767810] block: extroot: not configured [ 16.816980] UBIFS (ubi0:1): un-mount UBI device 0 [ 16.873287] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops [ 16.959728] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 1021 [ 17.046583] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 17.140443] UBIFS (ubi0:1): LEB size: 15872 bytes (15 KiB), min./max. I/O unit sizes: 512 bytes/512 bytes [ 17.255119] UBIFS (ubi0:1): FS size: 18824192 bytes (17 MiB, 1186 LEBs), journal size 936448 bytes (0 MiB, 59 LEBs) [ 17.380208] UBIFS (ubi0:1): reserved for root: 889112 bytes (868 KiB) [ 17.457391] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID B8615344-E6AD-4B1A-AB04-06EA22F30C5E, small LPT model [ 17.593291] UBIFS (ubi0:1): full atime support is enabled. [ 17.860321] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 17.945990] block: extroot: not configured [ 17.996251] mount_root: switching to ubifs overlay [ 18.061241] urandom-seed: Seeding with /etc/urandom.seed [ 18.190267] procd: - early - [ 18.224818] procd: - watchdog - [ 19.366208] procd: - watchdog - [ 19.423441] procd: - ubus - [ 19.560123] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available) [ 19.767225] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available) [ 19.979424] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 20.181227] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 21.107853] procd: - init - Please press Enter to activate this console.
Re: Debian on QiZhiTong 501mv2 August 14, 2017 05:54PM |
Admin Registered: 13 years ago Posts: 18,550 |
Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=1 root=/ initrd=/boot/uInitrd console=ttyS0,9600
modprobe mv88e6085
/dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "QiZhiTong 501M V2"; compatible = "qizhitong,501m_v2","marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; chosen { bootargs = "console=ttyS0,9600n8 earlyprintk"; }; mbus { pcie-controller { status = "okay"; pcie@1,0 { status = "okay"; }; }; }; ocp@f1000000 { pinctrl: pin-controller@10000 { pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { marvell,pins = "mpp28"; marvell,function = "gpio"; }; }; serial@12000 { status = "okay"; }; sata@80000 { status = "okay"; nr-ports = <1>; }; mvsdio@90000 { pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; pinctrl-names = "default"; status = "okay"; cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; /* No WP GPIO */ }; }; dsa { status = "disabled"; compatible = "marvell,dsa"; #address-cells = <2>; #size-cells = <0>; dsa,ethernet = <ð0port>; dsa,mii-bus = <&mdio>; switch@10,0 { #address-cells = <1>; #size-cells = <0>; reg = <10 0>; /* MDIO address 16, switch 0 in tree */ port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; }; }; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "kernel"; reg = <0x0100000 0x400000>; }; partition@500000 { label = "ubi"; reg = <0x0500000 0x3b00000>; }; }; &mdio { status = "okay"; switch@0 { compatible = "marvell,mv88e6085"; #address-cells = <1>; #size-cells = <0>; reg = <10>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <ð0port>; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; ð0 { status = "okay"; ethernet0-port@0 { speed = <1000>; duplex = <1>; }; }; ð1 { status = "okay"; ethernet1-port@0 { }; };
Re: Debian on QiZhiTong 501mv2 August 15, 2017 01:29AM |
Registered: 8 years ago Posts: 166 |
Re: Debian on QiZhiTong 501mv2 August 15, 2017 03:39AM |
Admin Registered: 13 years ago Posts: 18,550 |
printenv mmc help
Re: Debian on QiZhiTong 501mv2 August 15, 2017 08:59AM |
Registered: 8 years ago Posts: 166 |
bootm: BOOTCMD4 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: JMicron Firm: 100415 Ser#: 00000000002E9 Type: Hard Disk Supports 48-bit addressing Capacity: 3836.0 MB = 3.7 GB (7856128 x 512) 3832261 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.12.1-KIRKWOOD-TLD-1 Created: 2017-08-15 7:27:35 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3832197 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: rootdelay=10 root=/dev/sda1 console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 506352K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 17936K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000038] Switching to timer-based delay loop, resolution 5ns [ 0.000483] Console: colour dummy device 80x30 [ 0.000513] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000534] pid_max: default: 32768 minimum: 301 [ 0.000724] Security Framework initialized [ 0.000841] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000859] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001659] CPU: Testing write buffer coherency: ok [ 0.002556] Setting up static identity map for 0x100000 - 0x100058 [ 0.002793] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.005834] devtmpfs: initialized [ 0.009648] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.009673] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.010088] prandom: seed boundary self test passed [ 0.013840] prandom: 100 self tests passed [ 0.013851] pinctrl core: initialized pinctrl subsystem [ 0.014916] NET: Registered protocol family 16 [ 0.015310] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.016799] cpuidle: using governor ladder [ 0.016863] cpuidle: using governor menu [ 0.017237] Feroceon L2: Enabling L2 [ 0.017280] Feroceon L2: Cache support initialised. [ 0.017626] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.017733] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.022395] No ATAGs? [ 0.031357] vgaarb: loaded [ 0.031663] SCSI subsystem initialized [ 0.032128] usbcore: registered new interface driver usbfs [ 0.032205] usbcore: registered new interface driver hub [ 0.032290] usbcore: registered new device driver usb [ 0.033333] clocksource: Switched to clocksource orion_clocksource [ 0.121555] VFS: Disk quotas dquot_6.6.0 [ 0.121630] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.132100] NET: Registered protocol family 2 [ 0.132814] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.132875] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.132927] TCP: Hash tables configured (established 4096 bind 4096) [ 0.133007] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.133031] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.133198] NET: Registered protocol family 1 [ 0.133644] RPC: Registered named UNIX socket transport module. [ 0.133657] RPC: Registered udp transport module. [ 0.133664] RPC: Registered tcp transport module. [ 0.133671] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.133989] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.134877] audit: initializing netlink subsys (disabled) [ 0.135319] Initialise system trusted keyrings [ 0.135370] Key type blacklist registered [ 0.135469] audit: type=2000 audit(0.131:1): state=initialized audit_enabled=0 res=1 [ 0.135552] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.135618] zbud: loaded [ 0.136589] NFS: Registering the id_resolver key type [ 0.136618] Key type id_resolver registered [ 0.136626] Key type id_legacy registered [ 0.136643] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.136653] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.136860] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.137044] fuse init (API version 7.26) [ 0.137403] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.137658] orangefs_init: module version upstream loaded [ 0.137669] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.553344] random: fast init done [ 6.002439] Key type asymmetric registered [ 6.002454] Asymmetric key parser 'x509' registered [ 6.002516] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.002527] io scheduler noop registered [ 6.002535] io scheduler deadline registered [ 6.002605] io scheduler cfq registered (default) [ 6.003912] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.005667] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.064066] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.064280] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.124062] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.124452] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.125659] console [ttyS0] disabled [ 6.125721] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 13.245609] console [ttyS0] enabled [ 13.295779] loop: module loaded [ 13.333927] sata_mv f1080000.sata: slots 32 ports 1 [ 13.393866] scsi host0: sata_mv [ 13.431663] ata1: SATA max UDMA/133 irq 32 [ 13.481299] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 13.557478] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 13.612754] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 13.700353] Scanning device for bad blocks [ 13.878535] Bad eraseblock 2455 at 0x00000265c000 [ 14.021002] 3 ofpart partitions found on MTD device orion_nand [ 14.090849] Creating 3 MTD partitions on "orion_nand": [ 14.152426] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 14.227718] ata1.00: ATA-7: JMicron, 100415, max UDMA/133 [ 14.227725] ata1.00: 7856128 sectors, multi 1: LBA48 [ 14.292713] ata1.00: configured for UDMA/133 [ 14.353673] scsi 0:0:0:0: Direct-Access ATA JMicron 15 PQ: 0 ANSI: 5 [ 14.355083] sd 0:0:0:0: [sda] 7856128 512-byte logical blocks: (4.02 GB/3.75 GiB) [ 14.355149] sd 0:0:0:0: [sda] Write Protect is off [ 14.355271] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 14.504925] sda: sda1 sda2 [ 14.506601] sd 0:0:0:0: [sda] Attached SCSI disk [ 14.851841] 0x000000000000-0x000000100000 : "u-boot" [ 14.912612] 0x000000100000-0x000000500000 : "kernel" [ 14.973547] 0x000000500000-0x000004000000 : "ubi" [ 15.035423] libphy: Fixed MDIO Bus: probed [ 15.085306] libphy: orion_mdio_bus: probed [ 15.134691] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 15.217369] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 15.322174] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 15.426507] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 15.504733] ehci-pci: EHCI PCI platform driver [ 15.557994] ehci-orion: EHCI orion driver [ 15.606137] orion-ehci f1050000.ehci: EHCI Host Controller [ 15.671926] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 15.763816] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 15.863370] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 15.935543] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 16.016906] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.103429] usb usb1: Product: EHCI Host Controller [ 16.161864] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 16.242167] usb usb1: SerialNumber: f1050000.ehci [ 16.299141] hub 1-0:1.0: USB hub found [ 16.344106] hub 1-0:1.0: 1 port detected [ 16.391640] usbcore: registered new interface driver usb-storage [ 16.463974] mousedev: PS/2 mouse device common for all mice [ 16.531371] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 16.613869] i2c /dev entries driver [ 16.656657] hidraw: raw HID events driver (C) Jiri Kosina [ 16.721775] drop_monitor: Initializing network drop monitor service [ 16.797187] NET: Registered protocol family 17 [ 16.850445] Key type dns_resolver registered [ 16.901626] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 16.982733] registered taskstats version 1 [ 17.031836] Loading compiled-in X.509 certificates [ 17.089361] zswap: loaded using pool lzo/zbud [ 17.143937] Key type big_key registered [ 17.191793] Key type encrypted registered [ 17.241174] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 17.342837] usb 1-1: New USB device found, idVendor=04cc, idProduct=1520 [ 17.423318] Waiting 10 sec before mounting root device... [ 17.488077] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 17.574418] hub 1-1:1.0: USB hub found [ 17.619455] hub 1-1:1.0: 2 ports detected [ 28.003949] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 28.091126] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 28.173527] EXT4-fs (sda1): write access will be enabled during recovery [ 28.268947] EXT4-fs (sda1): recovery complete [ 28.322094] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 28.413936] VFS: Mounted root (ext3 filesystem) readonly on device 8:1. [ 28.495695] devtmpfs: mounted [ 28.534068] Freeing unused kernel memory: 1024K INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. ERROR: could not open /proc/stat: No such file or directory findfs: unable to resolve 'LABEL=rootfs' [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 30.138684] marvell-cesa f1030000.crypto: CESA device successfully registered [ 30.269353] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 30.287373] mv88e6085 f1072004.mdio-bus-mii:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 30.400988] libphy: mv88e6xxx SMI: probed [ 30.401052] DSA: switch 0 0 parsed [ 30.401054] DSA: tree 0 parsed [ 31.275102] orion_wdt: Initial timeout 21 sec [ 31.331253] mvsdio f1090000.mvsdio: Got CD GPIO [ 31.855153] random: crng init done [ 31.904867] mv88e6085 f1072004.mdio-bus-mii:0a lan1: no phy at 0 [ 31.976815] mv88e6085 f1072004.mdio-bus-mii:0a lan1: failed to connect to port 0: -19 [ 32.070670] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.193401] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 0: -19 [ 32.280404] mv88e6085 f1072004.mdio-bus-mii:0a lan2: no phy at 1 [ 32.352458] mv88e6085 f1072004.mdio-bus-mii:0a lan2: failed to connect to port 1: -19 [ 32.446267] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.563396] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 1: -19 [ 32.650506] mv88e6085 f1072004.mdio-bus-mii:0a lan3: no phy at 2 [ 32.722538] mv88e6085 f1072004.mdio-bus-mii:0a lan3: failed to connect to port 2: -19 [ 32.816349] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.933398] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 2: -19 [ 33.020505] mv88e6085 f1072004.mdio-bus-mii:0a lan4: no phy at 3 [ 33.092516] mv88e6085 f1072004.mdio-bus-mii:0a lan4: failed to connect to port 3: -19 [ 33.186516] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 33.303397] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 3: -19 [ 33.390453] mv88e6085 f1072004.mdio-bus-mii:0a aux: no phy at 4 [ 33.461449] mv88e6085 f1072004.mdio-bus-mii:0a aux: failed to connect to port 4: -19 [ 33.554218] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 33.673397] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 4: -19 done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 40.937604] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14453/196608 fi[ 41.193645] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro les, 198268/786432 blocks . ok [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files.... [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Initializing random number generator...done. [ ok ] Setting kernel variables...done. [ 43.616298] mv643xx_eth: no PHY [ 43.616336] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:90:0b:19:ee:25 Sending on LPF/eth0/00:90:0b:19:ee:25 Sending on Socket/fallback DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 [ 125.589432] NET: Registered protocol family 10 [ 125.646164] Segment Routing with IPv6 DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 2 No DHCPOFFERS received. Trying recorded lease 192.168.0.14 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. --- 192.168.0.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1288 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1286 (klogd) . ok [ ok ] Running local boot scripts (/etc/rc.local).
Re: Debian on QiZhiTong 501mv2 August 15, 2017 04:35PM |
Admin Registered: 13 years ago Posts: 18,550 |
[ 30.287373] mv88e6085 f1072004.mdio-bus-mii:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 30.400988] libphy: mv88e6xxx SMI: probed [ 30.401052] DSA: switch 0 0 parsed [ 30.401054] DSA: tree 0 parsed [ 31.275102] orion_wdt: Initial timeout 21 sec [ 31.331253] mvsdio f1090000.mvsdio: Got CD GPIO [ 31.855153] random: crng init done [ 31.904867] mv88e6085 f1072004.mdio-bus-mii:0a lan1: no phy at 0 [ 31.976815] mv88e6085 f1072004.mdio-bus-mii:0a lan1: failed to connect to port 0: -19 [ 32.070670] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.193401] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 0: -19 [ 32.280404] mv88e6085 f1072004.mdio-bus-mii:0a lan2: no phy at 1 [ 32.352458] mv88e6085 f1072004.mdio-bus-mii:0a lan2: failed to connect to port 1: -19 [ 32.446267] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.563396] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 1: -19 [ 32.650506] mv88e6085 f1072004.mdio-bus-mii:0a lan3: no phy at 2 [ 32.722538] mv88e6085 f1072004.mdio-bus-mii:0a lan3: failed to connect to port 2: -19 [ 32.816349] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.933398] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 2: -19 [ 33.020505] mv88e6085 f1072004.mdio-bus-mii:0a lan4: no phy at 3 [ 33.092516] mv88e6085 f1072004.mdio-bus-mii:0a lan4: failed to connect to port 3: -19 [ 33.186516] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 33.303397] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 3: -19 [ 33.390453] mv88e6085 f1072004.mdio-bus-mii:0a aux: no phy at 4 [ 33.461449] mv88e6085 f1072004.mdio-bus-mii:0a aux: failed to connect to port 4: -19 [ 33.554218] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 33.673397] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 4: -19
Re: Debian on QiZhiTong 501mv2 August 15, 2017 06:24PM |
Admin Registered: 13 years ago Posts: 18,550 |
&mdio { status = "okay"; switch@0 { compatible = "marvell,mv88e6085"; #address-cells = <1>; #size-cells = <0>; reg = <10>;
switch@a {or
switch@10 {or
switch@16 {
switch@10 {
Re: Debian on QiZhiTong 501mv2 August 15, 2017 10:34PM |
Registered: 8 years ago Posts: 166 |
[ 30.098888] mv88e6085 f1072004.mdio-bus-mii:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 30.213967] libphy: mv88e6xxx SMI: probed [ 30.214037] DSA: switch 0 0 parsed [ 30.214040] DSA: tree 0 parsed [ 31.329260] orion_wdt: Initial timeout 21 sec [ 31.385499] mvsdio f1090000.mvsdio: Got CD GPIO [ 31.658546] random: crng init done [ 31.911864] mv88e6085 f1072004.mdio-bus-mii:0a lan1: no phy at 0 [ 31.983897] mv88e6085 f1072004.mdio-bus-mii:0a lan1: failed to connect to port 0: -19 [ 32.077829] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.193386] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 0: -19 [ 32.280474] mv88e6085 f1072004.mdio-bus-mii:0a lan2: no phy at 1 [ 32.352452] mv88e6085 f1072004.mdio-bus-mii:0a lan2: failed to connect to port 1: -19 [ 32.446270] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.563388] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 1: -19 [ 32.650557] mv88e6085 f1072004.mdio-bus-mii:0a lan3: no phy at 2 [ 32.722533] mv88e6085 f1072004.mdio-bus-mii:0a lan3: failed to connect to port 2: -19 [ 32.816348] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 32.933383] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 2: -19 [ 33.020540] mv88e6085 f1072004.mdio-bus-mii:0a lan4: no phy at 3 [ 33.092587] mv88e6085 f1072004.mdio-bus-mii:0a lan4: failed to connect to port 3: -19 [ 33.186561] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 33.303387] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 3: -19 [ 33.390528] mv88e6085 f1072004.mdio-bus-mii:0a aux: no phy at 4 [ 33.461548] mv88e6085 f1072004.mdio-bus-mii:0a aux: failed to connect to port 4: -19 [ 33.554322] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -19 setting up slave phy [ 33.673386] mv88e6085 f1072004.mdio-bus-mii:0a: Failed to create slave 4: -19
Re: Debian on QiZhiTong 501mv2 August 16, 2017 12:27AM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Debian on QiZhiTong 501mv2 August 16, 2017 05:09PM |
Admin Registered: 13 years ago Posts: 18,550 |
ls -lR /proc/device-tree/dsa -Rand
ls -lR /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii*
Re: Debian on QiZhiTong 501mv2 August 16, 2017 08:03PM |
Admin Registered: 13 years ago Posts: 18,550 |
[MV88E6161] = {
.prod_num = PORT_SWITCH_ID_PROD_NUM_6161,
.family = MV88E6XXX_FAMILY_6165,
.name = "Marvell 88E6161",
.num_databases = 4096,
.num_ports = 6,
.max_vid = 4095,
.port_base_addr = 0x10,
.global1_addr = 0x1b,
.age_time_coeff = 15000,
.g1_irqs = 9,
.atu_move_port_mask = 0xf,
.pvt = true,
.tag_protocol = DSA_TAG_PROTO_DSA,
.flags = MV88E6XXX_FLAGS_FAMILY_6165,
.ops = &mv88e6161_ops,
},
/dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "QiZhiTong 501M V2"; compatible = "qizhitong,501m_v2","marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; chosen { bootargs = "console=ttyS0,9600n8 earlyprintk"; }; mbus { pcie-controller { status = "okay"; pcie@1,0 { status = "okay"; }; }; }; ocp@f1000000 { pinctrl: pin-controller@10000 { pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { marvell,pins = "mpp28"; marvell,function = "gpio"; }; }; serial@12000 { status = "okay"; }; sata@80000 { status = "okay"; nr-ports = <1>; }; mvsdio@90000 { pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; pinctrl-names = "default"; status = "okay"; cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; /* No WP GPIO */ }; }; dsa { status = "disabled"; compatible = "marvell,dsa"; #address-cells = <2>; #size-cells = <0>; dsa,ethernet = <ð0port>; dsa,mii-bus = <&mdio>; switch@10,0 { #address-cells = <1>; #size-cells = <0>; reg = <10 0>; /* MDIO address 16, switch 0 in tree */ port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; }; }; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "kernel"; reg = <0x0100000 0x400000>; }; partition@500000 { label = "ubi"; reg = <0x0500000 0x3b00000>; }; }; &mdio { status = "okay"; switch@16 { compatible = "marvell,mv88e6085"; #address-cells = <1>; #size-cells = <0>; reg = <16>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan1"; }; port@1 { reg = <1>; label = "lan2"; }; port@2 { reg = <2>; label = "lan3"; }; port@3 { reg = <3>; label = "lan4"; }; port@4 { reg = <4>; label = "aux"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <ð0port>; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; ð0 { status = "okay"; ethernet0-port@0 { speed = <1000>; duplex = <1>; }; }; ð1 { status = "okay"; ethernet1-port@0 { }; };
Re: Debian on QiZhiTong 501mv2 August 16, 2017 08:53PM |
Registered: 8 years ago Posts: 166 |
Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.37 (Wacke@HOME-Server) (gcc version 7.1.0 (LEDE GCC 7.1.0 r4235-61eb18d3f7) ) #0 Thu Jul 27 10:12:21 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt:Machine model: QiZhiTong 501M V2 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,9600 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 513260K/524288K available (4433K kernel code, 282K rwdata, 1208K rodata, 240K init, 224K bss, 11028K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc045c700 (4434 kB) [ 0.000000] .init : 0xc058c000 - 0xc05c8000 ( 240 kB) [ 0.000000] .data : 0xc05c8000 - 0xc060e938 ( 283 kB) [ 0.000000] .bss : 0xc060e938 - 0xc0646d30 ( 225 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000098] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090090] pid_max: default: 32768 minimum: 301 [ 0.090216] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090235] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090866] CPU: Testing write buffer coherency: ok [ 0.091172] Setting up static identity map for 0x81e0 - 0x821c [ 0.091434] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.096654] VFP support v0.3: not present [ 0.096858] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.096884] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.096982] pinctrl core: initialized pinctrl subsystem [ 0.097951] NET: Registered protocol family 16 [ 0.098277] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.099696] cpuidle: using governor ladder [ 0.100070] Feroceon L2: Enabling L2 [ 0.100111] Feroceon L2: Cache support initialised. [ 0.100394] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.100509] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.105111] No ATAGs? [ 0.122385] SCSI subsystem initialized [ 0.123168] usbcore: registered new interface driver usbfs [ 0.123255] usbcore: registered new interface driver hub [ 0.123323] usbcore: registered new device driver usb [ 0.125461] clocksource: Switched to clocksource orion_clocksource [ 0.141203] NET: Registered protocol family 2 [ 0.141826] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.141886] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.141938] TCP: Hash tables configured (established 4096 bind 4096) [ 0.142001] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.142024] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.142183] NET: Registered protocol family 1 [ 0.145083] Crashlog allocated RAM at address 0x3f00000 [ 0.145602] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.154714] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.154727] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.162726] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.162741] io scheduler noop registered [ 0.162749] io scheduler deadline registered (default) [ 0.164004] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.199702] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.200746] console [ttyS0] disabled [ 0.200815] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 5.243790] console [ttyS0] enabled [ 5.286629] sata_mv f1080000.sata: slots 32 ports 1 [ 5.347203] scsi host0: sata_mv [ 5.385251] ata1: SATA max UDMA/133 irq 32 [ 5.434776] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x76 [ 5.510853] nand: ST Micro NAND 64MiB 3,3V 8-bit [ 5.566154] nand: 64 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 5.653757] Scanning device for bad blocks [ 5.833475] Bad eraseblock 2455 at 0x00000265c000 [ 5.977053] 3 ofpart partitions found on MTD device orion_nand [ 6.046957] Creating 3 MTD partitions on "orion_nand": [ 6.108519] 0x000000000000-0x000000100000 : "u-boot" [ 6.169817] 0x000000100000-0x000000500000 : "kernel" [ 6.230721] 0x000000500000-0x000004000000 : "ubi" [ 6.292070] libphy: Fixed MDIO Bus: probed [ 6.341687] libphy: mdio_driver_register: mv88e6085 [ 6.400363] libphy: orion_mdio_bus: probed [ 6.449471] mdio_bus f1072004.mdio-bu:0a: mdio_device_register [ 6.521753] mv88e6085 f1072004.mdio-bu:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 6.629116] ata1: SATA link down (SStatus 0 SControl F300) [ 6.708636] random: fast init done [ 6.769318] libphy: /ocp@f1000000/mdio-bus@72004/switch@10: probed [ 6.843917] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.926876] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:90:0b:19:ee:25 [ 7.031870] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:90:0b:19:ee:26 [ 7.136212] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.214384] ehci-pci: EHCI PCI platform driver [ 7.267679] ehci-orion: EHCI orion driver [ 7.315791] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.381494] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.473346] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 7.565484] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.638239] hub 1-0:1.0: USB hub found [ 7.683318] hub 1-0:1.0: 1 port detected [ 7.730771] usbcore: registered new interface driver usb-storage [ 7.803128] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 7.885547] i2c /dev entries driver [ 7.927919] orion_wdt: Initial timeout 21 sec [ 7.980668] mvsdio f1090000.mvsdio: Got CD GPIO [ 8.091100] marvell-cesa f1030000.crypto: CESA device successfully registered [ 8.177462] NET: Registered protocol family 10 [ 8.232583] NET: Registered protocol family 17 [ 8.285954] 8021q: 802.1Q VLAN Support v1.8 [ 8.340236] mv88e6085 f1072004.mdio-bu:0a: switch 0x161 detected: Marvell 88E6161, revision 2 [ 8.442585] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.563474] libphy: /ocp@f1000000/mdio-bus@72004/switch@10: probed [ 8.637576] DSA: switch 0 0 parsed [ 8.678248] DSA: tree 0 parsed [ 8.826535] hub 1-1:1.0: USB hub found [ 8.871645] hub 1-1:1.0: 2 ports detected [ 9.779657] mv88e6085 f1072004.mdio-bu:0a lan1: failed to connect to port 0: -110 [ 9.869329] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -110 setting up slave phy [ 9.963789] mv88e6085 f1072004.mdio-bu:0a: Failed to create slave 0: -110 [ 10.889628] mv88e6085 f1072004.mdio-bu:0a lan2: failed to connect to port 1: -110 [ 10.979257] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -110 setting up slave phy [ 11.073620] mv88e6085 f1072004.mdio-bu:0a: Failed to create slave 1: -110 [ 11.999642] mv88e6085 f1072004.mdio-bu:0a lan3: failed to connect to port 2: -110 [ 12.089292] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -110 setting up slave phy [ 12.183645] mv88e6085 f1072004.mdio-bu:0a: Failed to create slave 2: -110 [ 13.109657] mv88e6085 f1072004.mdio-bu:0a lan4: failed to connect to port 3: -110 [ 13.199322] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -110 setting up slave phy [ 13.293675] mv88e6085 f1072004.mdio-bu:0a: Failed to create slave 3: -110 [ 14.219629] mv88e6085 f1072004.mdio-bu:0a aux: failed to connect to port 4: -110 [ 14.308209] mv643xx_eth_port mv643xx_eth_port.0 eth0: error -110 setting up slave phy [ 14.402563] mv88e6085 f1072004.mdio-bu:0a: Failed to create slave 4: -110 [ 14.484352] UBI: auto-attach mtd2 [ 14.524036] ubi0: attaching mtd2 [ 14.888107] ubi0: scanning is finished [ 14.945216] ubi0: attached mtd2 (name "ubi", size 59 MiB) [ 15.009958] ubi0: PEB size: 16384 bytes (16 KiB), LEB size: 15872 bytes [ 15.089191] ubi0: min./max. I/O unit sizes: 512/512, sub-page size 256 [ 15.167417] ubi0: VID header offset: 256 (aligned 256), data offset: 512 [ 15.247724] ubi0: good PEBs: 3775, bad PEBs: 1, corrupted PEBs: 0 [ 15.320741] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 92 [ 15.406254] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1830178591 [ 15.515729] ubi0: available PEBs: 0, total reserved PEBs: 3775, PEBs reserved for bad PEB handling: 79 [ 15.627635] ubi0: background thread "ubi_bgt0d" started, PID 968 [ 15.700342] block ubiblock0_0: created from ubi0:0(rootfs) [ 15.766041] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 15.849483] rtc-mv f1010300.rtc: setting system clock to 2000-02-16 12:30:34 UTC (950704234) [ 15.955567] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 16.041806] Freeing unused kernel memory: 240K (c058c000 - c05c8000) [ 16.117885] This architecture does not have kernel memory protection. [ 16.575454] init: Console is alive [ 16.616324] init: - watchdog - [ 17.870955] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 18.040229] exFAT: Version 1.2.9 [ 18.082329] ehci-platform: EHCI generic platform driver [ 18.149792] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 18.225017] ohci-platform: OHCI generic platform driver [ 18.289302] uhci_hcd: USB Universal Host Controller Interface driver [ 18.371774] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 18.468657] init: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 22.541121] mount_root: loading kmods from internal overlay [ 22.637850] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 22.724337] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 23.216763] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 1065 [ 23.303503] UBIFS (ubi0:1): recovery needed [ 23.374348] UBIFS (ubi0:1): recovery completed [ 23.427610] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 23.521475] UBIFS (ubi0:1): LEB size: 15872 bytes (15 KiB), min./max. I/O unit sizes: 512 bytes/512 bytes [ 23.636160] UBIFS (ubi0:1): FS size: 18824192 bytes (17 MiB, 1186 LEBs), journal size 936448 bytes (0 MiB, 59 LEBs) [ 23.761247] UBIFS (ubi0:1): reserved for root: 889112 bytes (868 KiB) [ 23.838430] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID B8615344-E6AD-4B1A-AB04-06EA22F30C5E, small LPT model [ 23.976288] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 24.062142] block: extroot: not configured [ 24.111396] UBIFS (ubi0:1): un-mount UBI device 0 [ 24.167698] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops [ 24.255937] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 1067 [ 24.342793] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 24.436631] UBIFS (ubi0:1): LEB size: 15872 bytes (15 KiB), min./max. I/O unit sizes: 512 bytes/512 bytes [ 24.551303] UBIFS (ubi0:1): FS size: 18824192 bytes (17 MiB, 1186 LEBs), journal size 936448 bytes (0 MiB, 59 LEBs) [ 24.676398] UBIFS (ubi0:1): reserved for root: 889112 bytes (868 KiB) [ 24.753578] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID B8615344-E6AD-4B1A-AB04-06EA22F30C5E, small LPT model [ 25.094642] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 25.180271] block: extroot: not configured [ 25.230443] mount_root: switching to ubifs overlay [ 25.318252] urandom-seed: Seeding with /etc/urandom.seed [ 25.441829] procd: - early - [ 25.476768] procd: - watchdog - [ 26.555302] procd: - watchdog - [ 26.593623] procd: - ubus - [ 26.827831] procd: - init - Please press Enter to activate this console. [ 27.390919] kmodloader: loading kernel modules from /etc/modules.d/* [ 27.582980] ntfs: driver 2.1.32 [Flags: R/O MODULE]. [ 27.752933] tun: Universal TUN/TAP device driver, 1.6 [ 27.813408] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 28.026723] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 28.163552] l2tp_core: L2TP core driver, V2.0 [ 28.276605] l2tp_netlink: L2TP netlink interface [ 28.381796] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 28.528022] gre: GRE over IPv4 demultiplexor driver [ 28.646969] ip_gre: GRE over IPv4 tunneling driver [ 28.768295] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 28.911347] Netfilter messages via NETLINK v0.30. [ 29.028037] ip_set: protocol 6 [ 29.155664] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f [ 29.251634] Backport generated by backports.git backports-20160324-13-g24da7d3c [ 29.668940] u32 classifier [ 29.701297] input device check on [ 29.745125] Actions configured [ 29.907381] Mirror/redirect action on [ 29.994772] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 30.199722] fuse init (API version 7.26) [ 30.363527] usbcore: registered new interface driver cdc_wdm [ 30.508389] ip_tables: (C) 2000-2006 Netfilter Core Team [ 30.640146] lib80211: common routines for IEEE802.11 drivers [ 30.785114] ctnetlink v0.93: registering with nfnetlink. [ 31.038574] wireguard: WireGuard 0.0.20170706 loaded. See www.wireguard.io for information. [ 31.138725] wireguard: Copyright (C) 2015-2017 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 31.530034] xt_time: kernel timezone is -0000 [ 31.649967] usbcore: registered new interface driver ath9k_htc [ 31.842103] PPP generic driver version 2.4.2 [ 31.949656] PPP MPPE Compression module registered [ 32.066995] NET: Registered protocol family 24 [ 32.176907] PPTP driver version 0.8.5 [ 32.256409] usbcore: registered new interface driver qmi_wwan [ 32.428717] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 32.551599] kmodloader: done loading kernel modules from /etc/modules.d/* [ 48.347387] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 48.779243] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 49.501489] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 50.095392] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 104.325508] random: crng init done
root@debian:~# ls -lR /proc/device-tree/dsa -R /proc/device-tree/dsa: total 0 -r--r--r-- 1 root root 4 Dec 31 16:03 #address-cells -r--r--r-- 1 root root 4 Dec 31 16:03 #size-cells drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 12 Dec 31 16:03 compatible -r--r--r-- 1 root root 4 Dec 31 16:03 dsa,ethernet -r--r--r-- 1 root root 4 Dec 31 16:03 dsa,mii-bus -r--r--r-- 1 root root 4 Dec 31 16:03 name -r--r--r-- 1 root root 9 Dec 31 16:03 status drwxr-xr-x 8 root root 0 Dec 31 16:03 switch@10,0 /proc/device-tree/dsa/switch@10,0: total 0 -r--r--r-- 1 root root 4 Dec 31 16:03 #address-cells -r--r--r-- 1 root root 4 Dec 31 16:03 #size-cells drwxr-xr-x 8 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 7 Dec 31 16:03 name drwxr-xr-x 2 root root 0 Dec 31 16:03 port@0 drwxr-xr-x 2 root root 0 Dec 31 16:03 port@1 drwxr-xr-x 2 root root 0 Dec 31 16:03 port@2 drwxr-xr-x 2 root root 0 Dec 31 16:03 port@3 drwxr-xr-x 2 root root 0 Dec 31 16:03 port@4 drwxr-xr-x 2 root root 0 Dec 31 16:03 port@5 -r--r--r-- 1 root root 8 Dec 31 16:03 reg /proc/device-tree/dsa/switch@10,0/port@0: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 8 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 5 Dec 31 16:03 label -r--r--r-- 1 root root 5 Dec 31 16:03 name -r--r--r-- 1 root root 4 Dec 31 16:03 reg /proc/device-tree/dsa/switch@10,0/port@1: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 8 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 5 Dec 31 16:03 label -r--r--r-- 1 root root 5 Dec 31 16:03 name -r--r--r-- 1 root root 4 Dec 31 16:03 reg /proc/device-tree/dsa/switch@10,0/port@2: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 8 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 5 Dec 31 16:03 label -r--r--r-- 1 root root 5 Dec 31 16:03 name -r--r--r-- 1 root root 4 Dec 31 16:03 reg /proc/device-tree/dsa/switch@10,0/port@3: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 8 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 5 Dec 31 16:03 label -r--r--r-- 1 root root 5 Dec 31 16:03 name -r--r--r-- 1 root root 4 Dec 31 16:03 reg /proc/device-tree/dsa/switch@10,0/port@4: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 8 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4 Dec 31 16:03 label -r--r--r-- 1 root root 5 Dec 31 16:03 name -r--r--r-- 1 root root 4 Dec 31 16:03 reg /proc/device-tree/dsa/switch@10,0/port@5: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 8 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4 Dec 31 16:03 label -r--r--r-- 1 root root 5 Dec 31 16:03 name -r--r--r-- 1 root root 4 Dec 31 16:03 reg
us-mii*bian:~# ls -lR /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bu /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a: total 0 drwxr-xr-x 4 root root 0 Dec 31 16:03 . drwxr-xr-x 4 root root 0 Dec 31 16:03 .. lrwxrwxrwx 1 root root 0 Dec 31 16:03 driver -> ../../../../../../../bus/mdio_bus/drivers/mv88e6085 drwxr-xr-x 3 root root 0 Dec 31 16:03 mdio_bus lrwxrwxrwx 1 root root 0 Dec 31 16:03 of_node -> ../../../../../../../firmware/devicetree/base/ocp@f1000000/mdio-bus@72004/switch@10 drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../bus/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus: total 0 drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 4 root root 0 Dec 31 16:03 .. drwxr-xr-x 10 root root 0 Dec 31 16:03 mv88e6xxx-0 /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0: total 0 drwxr-xr-x 10 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. lrwxrwxrwx 1 root root 0 Dec 31 16:03 device -> ../../../f1072004.mdio-bus-mii:0a drwxr-xr-x 3 root root 0 Dec 31 16:03 mv88e6xxx-0:10 drwxr-xr-x 3 root root 0 Dec 31 16:03 mv88e6xxx-0:11 drwxr-xr-x 3 root root 0 Dec 31 16:03 mv88e6xxx-0:12 drwxr-xr-x 3 root root 0 Dec 31 16:03 mv88e6xxx-0:13 drwxr-xr-x 3 root root 0 Dec 31 16:03 mv88e6xxx-0:14 drwxr-xr-x 3 root root 0 Dec 31 16:03 mv88e6xxx-0:15 drwxr-xr-x 3 root root 0 Dec 31 16:03 mv88e6xxx-0:1b drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../../../class/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:10: total 0 drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_has_fixups -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_id -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_interface drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../../../../bus/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:10/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:11: total 0 drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_has_fixups -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_id -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_interface drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../../../../bus/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:11/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:12: total 0 drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_has_fixups -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_id -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_interface drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../../../../bus/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:12/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:13: total 0 drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_has_fixups -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_id -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_interface drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../../../../bus/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:13/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:14: total 0 drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_has_fixups -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_id -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_interface drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../../../../bus/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:14/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:15: total 0 drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_has_fixups -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_id -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_interface drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../../../../bus/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:15/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:1b: total 0 drwxr-xr-x 3 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_has_fixups -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_id -r--r--r-- 1 root root 4096 Dec 31 16:03 phy_interface drwxr-xr-x 2 root root 0 Dec 31 16:03 power lrwxrwxrwx 1 root root 0 Dec 31 16:03 subsystem -> ../../../../../../../../../../bus/mdio_bus -rw-r--r-- 1 root root 4096 Dec 31 16:03 uevent /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/mv88e6xxx-0:1b/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 3 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/mdio_bus/mv88e6xxx-0/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 10 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time /sys/class/mdio_bus/f1072004.mdio-bus-mii/f1072004.mdio-bus-mii:0a/power: total 0 drwxr-xr-x 2 root root 0 Dec 31 16:03 . drwxr-xr-x 4 root root 0 Dec 31 16:03 .. -rw-r--r-- 1 root root 4096 Dec 31 16:03 autosuspend_delay_ms -rw-r--r-- 1 root root 4096 Dec 31 16:03 control -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_active_time -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_status -r--r--r-- 1 root root 4096 Dec 31 16:03 runtime_suspended_time