WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 11, 2016 03:37AM |
Registered: 9 years ago Posts: 19 |
BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6820 High speed PHY - Version: 2.0 Load WD GrandTeton Serdes Config: board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | PCIe0 | | 2 | 06 | SATA1 | | 3 | 05 | USB3 HOST1 | | 4 | 05 | USB3 HOST0 | | 5 | 00 | SGMII2 | -------------------------------- PCIe, Idx 0: detected no link High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.03 (Jul 30 2015 - 11:39:08) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fece000:0x1ff95bd4 BSS: 0x1ffef254 Stack: 0x1f9cdf20 Heap: 0x1f9ce000:0x1fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x500000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux-382 Created: 2015-08-02 3:54:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4093292 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Ramdisk Created: 2016-03-21 20:16:03 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 2274640 Bytes = 2.2 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Sun Aug 2 11:53:57 CST 2015 2014T30p5 Build-git3e9fe59 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 1 pages/cpu @c0930000 s8320 r8192 d16256 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16364 Kernel command line: root=/dev/ram console=ttyS0,115200 PID hash table entries: 2048 (order: -2, 8192 bytes) Dentry cache hash table entries: 65536 (order: 3, 262144 bytes) Inode-cache hash table entries: 32768 (order: 2, 131072 bytes) allocated 131072 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 512MB = 512MB total Memory: 511744k/511744k available, 12544k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff8000 ( 32 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0714278 (7217 kB) .init : 0xc0718000 - 0xc075a080 ( 265 kB) .data : 0xc075c000 - 0xc07a7e40 ( 304 kB) .bss : 0xc07a7e40 - 0xc0871570 ( 806 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p5 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 4096 Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc056c2b0 - 0xc056c308 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (5311.69 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 xor: measuring software checksum speed arm4regs : 1424.000 MB/sec 8regs : 940.800 MB/sec 32regs : 918.400 MB/sec xor: using function: arm4regs (1424.000 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ196, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ228, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 355 MB/s raid6: int32x2 347 MB/s raid6: int32x4 447 MB/s raid6: int32x8 384 MB/s raid6: using algorithm int32x4 (447 MB/s) raid6: using intx1 recovery algorithm mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Switching to clocksource armada_370_xp_clocksource NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 0, 32768 bytes) TCP bind hash table entries: 4096 (order: 0, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 1024 (order: 0, 32768 bytes) UDP-Lite hash table entries: 1024 (order: 0, 32768 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 2176K (c0f08000 - c1128000) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 8192 (order 0, 32768 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.22) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 1002 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC Nand Flash Timing = [WP : 12], [WH : 10] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 8 ofpart partitions found on MTD device armada-nand Creating 8 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "U-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "uRamdisk" 0x000000f00000-0x00000c800000 : "image.cfs" 0x00000c800000-0x00000d700000 : "rescue fw" 0x00000d700000-0x00000eb00000 : "config" 0x00000eb00000-0x00000f500000 : "reserve1" 0x00000f500000-0x00000ff00000 : "reserve2" SoC: model = 0x6820, revision = 0x4 mvPncVirtBase = 0xe0e00000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=2 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o egiga0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) port #1: is_sgmii=0, is_rgmii=1, phy_addr=1 o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048 o Port 1 is connected to Linux netdevice o egiga1, ifindex = 3, GbE port = 1 giga p=1: mtu=1500, mac=00:50:43:02:02:02 (platform) port #2: is_sgmii=1, is_rgmii=0, phy_addr=0 o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 o Port 2 is connected to Linux netdevice o egiga2, ifindex = 4, GbE port = 2 giga p=2: mtu=1500, mac=00:50:43:02:02:03 (platform) libphy: orion_mdio_bus: probed mdio_bus f1072004.mdio-mi: cannot get PHY at address 2 mdio_bus f1072004.mdio-mi: cannot get PHY at address 1 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata1.00: ATA-8: Hitachi HDS5C3020ALA632, ML6OAA10, max UDMA/133 ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: ATA-8: Hitachi HDS5C3020ALA632, ML6OAA10, max UDMA/133 ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 ML6O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Direct-Access ATA Hitachi HDS5C302 ML6O PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: Attached scsi generic sg1 type 0 sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sdb: sdb1 sdb2 sdb3 sdb4 sd 1:0:0:0: [sdb] Attached SCSI disk mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c0734f0c) TCP: cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 registered taskstats version 1 mvebu-rtc f10a3800.rtc: setting system clock to 2016-06-24 17:32:34 UTC (1466789554) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. RAMDISK: gzip image found at block 0 VFS: Mounted root (ext2 filesystem) readonly on device 1:0. devtmpfs: mounted Freeing unused kernel memory: 256K (c0718000 - c0758000) init started: BusyBox v1.20.2 (2014-10-30 15:28:59 CST) starting pid 1280, tty '': '/etc/rc.sh' ** Mounting /etc/fstab umount: can't umount /proc: Invalid argument umount: can't umount /usr/local/modules: Invalid argument sh: hotPlug.sh: not found sh: hotPlug.sh: not found offset_flag=1,vaule_flag=1,bit_flag=0 offset_flag=1,vaule_flag=1,bit_flag=0 offset_flag=1,vaulUBI: attaching mtd5 to ubi0 e_flag=1,bit_flag=0 offset_flag=1,vaule_flag=1,bit_flag=0 UBI: scanning is finished UBI: attached mtd5 (name "config", size 20 MiB) to ubi0 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 160, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 22/15, WL threshold: 4096, image sequence number: 379348779 UBI: available PEBs: 22, total reserved PEBs: 138, PEBs reserved for bad PEB handling: 10 UBI: background thread "ubi_bgt0d" started, PID 1302 UBI device number 0, total 160 LEBs (20316160 bytes, 19.4 MiB), available 22 LEBs (2793472 bytes, 2.7 MiB), LEB size 126976 bytes (124.0 KiB) UBIFS: background thread "ubifs_bgt0_0" started, PID 1307 UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "config" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 14475264 bytes (13 MiB, 114 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 683702 bytes (667 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID AE98572A-39B8-4422-A213-57C310B3CDDA, small LPT model umount: can't umount /usr/local/tmp/image.cfs: No such file or directory rm: can't remove '/usr/local/tmp/image.cfs': No such file or directory umount: can't umount /usr/local/tmp: Invalid argument first good block is 0 image len = 110747648 , image checksum = 9df075aa umount: can't umount /usr/local/tmp: Invalid argument dump image checksum=9df075aa mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules cp: can't stat '/tmp1/*': No such file or directory ln: /usr/sbin/./transmission-daemon: File exists ln: /usr/sbin/./transmission-remote: File exists ln: /lib/./liblber-2.4.so.2.5.6: File exists ln: /lib/./libminiupnpc.so: File exists ln: /lib/./libnatpmp.so: File exists ln: /lib/./libpam.so.0.81.6: File exists ln: /usr/local/sbin/alert_email_config.sh: File exists ln: /usr/sbin/language.sh: File exists dev.raid.speed_limit_max = 1000 egiga0 Link encap:Ethernet HWaddr 00:50:43:02:02:01 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:532 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:193 egiga2 Link encap:Ethernet HWaddr 00:50:43:02:02:03 egiga0: mac address changed BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:532 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:195 Do Lan Port Switch egiga2: mac address changed not_egiga0: mac address changed jnl: driver (UFSD_HEAD UFSD_HEAD_r244402_b37, LBD=ON) loaded at bf000000 ufsd: module license 'Commercial product' taints kernel. Disabling lock debugging due to kernel taint ufsd:: trace mask set to 0000000f ufsd: driver (UFSD_HEAD UFSD_HEAD_r244402_b37, build_host("swtest6"), acl, ioctl, bdi, sd2(0), fua, bz, tr, rsrc) loaded at bf020000 NTFS support included Hfs+/HfsJ support included optimized: speed Build_for__WD_Yellowstone_k3.10.39_2015-02-12_16T_UFSD_HEAD_r244402_b37 bio: create slab <bio-1> at 1 Btrfs loaded tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> lrwxrwxrwx 1 root 0 17 Jun 24 17:32 /usr/sbin//raid_config -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jun 24 17:32 /usr/sbin//raid_expand -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jun 24 17:32 /usr/sbin//raid_expand_disks -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jun 24 17:32 /usr/sbin//raid_update_info -> /usr/sbin/diskmgr hardware init pool #1: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga1: link up egiga1: started pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga2: link up egiga2: started mtd check v1.06.06032015 config mtd type is UBIFS device = /usr/local/config Total size = 12384 Kbytes Used size = 196 Kbytes Free size = 12188 Kbytes percentage = 2 /usr/local/config free size is 12480512 ** copy config files *** Copy orion.db from flash **** cp: can't stat '/usr/local/modules/files/fan_temperature.txt': No such file or directory *** symlink onbrd.ini from flash **** /etc/sysinit.d/wdlog: line 13: /etc/system.conf: No such file or directory ** set loopback interface UBI: attaching mtd6 to ubi1 UBI: scanning is finished UBI: attached mtd6 (name "reserve1", size 10 MiB) to ubi1 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 2179809531 UBI: available PEBs: 30, total reserved PEBs: 50, PEBs reserved for bad PEB handling: 12 UBI: background thread "ubi_bgt1d" started, PID 3432 UBI device number 1, total 80 LEBs (10158080 bytes, 9.7 MiB), available 30 LEBs (3809280 bytes, 3.6 MiB), LEB size 126976 bytes (124.0 KiB) UBIFS: background thread "ubifs_bgt1_0" started, PID 3450 UBIFS: mounted UBI device 1, volume 0, name "reserve" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 3047424 bytes (2 MiB, 24 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 143937 bytes (140 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID 27EB37EE-6C69-42ED-9525-C16ECD780B35, small LPT model UBIFS: un-mount UBI device 1, volume 0 UBIFS: background thread "ubifs_bgt1_0" stops UBI: attaching mtd7 to ubi2 UBI: scanning is finished UBI: attached mtd7 (name "reserve2", size 10 MiB) to ubi2 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1017015744 UBI: available PEBs: 20, total reserved PEBs: 60, PEBs reserved for bad PEB handling: 14 UBI: background thread "ubi_bgt2d" started, PID 3465 UBI device number 2, total 80 LEBs (10158080 bytes, 9.7 MiB), available 20 LEBs (2539520 bytes, 2.4 MiB), LEB size 126976 bytes (124.0 KiB) mknod: /dev/mtd7: File exists UBIFS: background thread "ubifs_bgt2_0" started, PID 3478 UBIFS: mounted UBI device 2, volume 0, name "reserve2" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 4063232 bytes (3 MiB, 32 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 191915 bytes (187 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID B08D71E6-2261-481A-AF47-E101DF7B74A7, small LPT model /dev/mtd7 mount ok(ubi) cp: can't stat '/mnt/ubi2/hidden_eccryption': No such file or directory UBIFS: un-mount UBI device 2, volume 0 UBIFS: background thread "ubifs_bgt2_0" stops mac1 = 00:90:A9:E8:51:D7 lan0:ifconfig egiga0 hegiga0: mac address changed w ether 00:90:A9:E8:51:D7 pool #2: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga0: link up egiga0: started set lan0 speed Model ID : GT GT ln: /usr/local/model/web/pages/images/./icon: File exists hidden encryption: 0 Not support chk_sata old firmware ver:2.11.140.0321.2016 new firmware ver:2.11.140.0321.2016 rm: can't remove '/tmp/fix_wd_config': No such file or directory *** execute rc.init.sh awk: /var/run/udhcpc0.pid: No such file or directory udhcpc (v1.20.2) started cat: can't open '/tmp/setip.0': No such file or directory Sending discover... Sending select for 192.168.151.214... Lease of 192.168.151.214 obtained, lease time 604800 deleting routers route: SIOCDELRT: No such process killall: crond: no process killed crond[3701]: crond: crond (busybox 1.20.2) started, log level 8 RTNETLINK answers: Operation not supported RTNETLINK answers: Operation not supported call load_module network Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.151.214 port = 49152 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.151.214:49152/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized crond[3760]: crond: crond (busybox 1.20.2) started, log level 8 /usr/local/modules/script/system_init: line 844: getHddWhiteList.sh: not found Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.151.214 port = 49153 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.151.214:49153/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized sh: you need to specify whom to kill Advertisements Sent Advertisements Sent *** Copy CacheVolume data from flash **** *** set Time Zone **** $Usage: apache {start|stop|restart} {web/dav} Fri Jun 24 17:33:08 PDT 2016 *** get Time from rtc and set it into system **** rtc: RTC time = 2016/6/24 Fri 17:33:8 Fri Jun 24 10:33:08 PDT 2016 Set Date & time : sntp -K /dev/null -S -r time.windows.com sntp 4.2.8@1.3265 Fri Jan 9 06:42:54 UTC 2015 (8) Module IPC SERVER Version:(1.00.20090706) ads=0 created mail daemon thread 0 2016-06-24 10:33:09.130197 (+0800) +0.5 +/- 0.424682 time.windows.com 40.118.103.7 s3 NTP Server connected successfully!!! POWER ON DEVICE!! md0 state is mdadm: /dev/sda1 appears to be part of a raid array: level=raid1 devices=2 ctime=Fri Jun 24 10:08:16 2016 mdadm: /dev/sdb1 appears to be part of a raid array: level=raid1 devices=2 ctime=Fri Jun 24 10:08:16 2016 mdadm: size set to 2097088K mdadm: creation continuing despite oddities due to --run md: bind<sda1> md: bind<sdb1> md/raid1:md0: active with 2 out of 2 mirrors md0: bitmap file is out of date (0 < 1) -- forcing full recovery created bitmap (16 pages) for device md0 md0: bitmap file is out of date, doing full recovery md0: bitmap initialized from disk: read 2 pages, set 262136 of 262136 bits md0: detected capacity change from 0 to 2147418112 mdadm: array /dev/md0 started. md0: unknown partition table Setting up swapspace version 1, size = 2147385344 bytes UUID=8dccf999-7632-4573-90d6-0039314754fe Adding 2097056k swap on /dev/md0. Priority:-1 extents:1 across:2097056k EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: (null) --->isVolumeExist 0 rtc: system time: 2016/6/24 Fri 17:33:13 setRTCTime EXT4-fs (sda2): barriers disabled EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: barrier=0,usrquota,grpquota --->isVolumeExist 0 EXT4-fs (sdb2): barriers disabled EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: barrier=0,usrquota,grpquota Up_Send_Ctl : Can not find specified command "ErrStatus" restart sysinfod... sysinfod: full update begin... cat: can't open '/tmp/hw_detect_sata': No such file or directory sysinfod: disk connected: previous=0xffffffff, now=0x0 sh: getHddWhiteList.sh: not found sysinfod: Disk1(sda) detected. sysinfod: Disk2(sdb) detected. sysinfod: Creating a new entry for md0. mdadm: No md superblock detected on /dev/sda2. mdadm: No md superblock detected on /dev/sdb2. mount: mount point /proc/bus/usb does not exist WD hwlib start.............. Starting system message bus Starting wdtms wdtms started PHY_LAN_NUMBER=1 BOND_ENABLE=0 VLAN0_ENABLE=0 VLAN1_ENABLE=0 **LLTD START** LLTDIF0=egiga0 I/O warning : failed to load external entity "/var/www/xml/internal_backup.xml" /usr/local/modules/script/system_init: line 1063: /mnt/tmp6/ibuki/avahi_tm_serv: not found --2016-06-24 10:33:26-- http://download.wdc.com/apps/WDMyCloudMirrorG2/WDMyCloudMirrorG2.xml Resolving download.wdc.com... cat: can't open '/var/run/traceroute_wd.pid': No such file or directory ash: you need to specify whom to kill 84.53.142.82, 84.53.142.89 Connecting to download.wdc.com|84.53.142.82|:80... killall: traceroute: no process killed connected. HTTP request sent, awaiting response... 200 OK Length: 7698 (7.5K) [application/xml] Saving to: '/var/www/xml/app_info.xml' 100%[======================================>] 7,698 --.-K/s in 0.007s 2016-06-24 10:33:26 (1.07 MB/s) - '/var/www/xml/app_info.xml' saved [7698/7698] I/O warning : failed to load external entity "/var/www/xml/app_update.xml" -------------use hwlib instead of fan_control b c------------- sysinfod: disk connected: previous=0x0, now=0x3 sh: getHddWhiteList.sh: not found waiting : [10] mcu version 1.06 chk_io v1.04.20141112 system daemon v1.04.20141211 PIP is disabled, exiting. Fri Jun 24 10:33:36 PDT 2016 - %W - Communication Manager - startup is disabled, use 'enable' to start process /usr/local/modules/script/system_init: line 1289: vvctl: not found dev.raid.speed_limit_max = 200000 Please press Enter to activate this console. killall: chk_hotplug: no process killed call load_module ### create systemfile ### ### sata_reload_application start ### PID file /var/run/mediaserver.pid not found, stopping server anyway... killall: twonkystarter: no process killed Starting /usr/local/twonky/twonkystarter ... -appdata /mnt/HD/HD_a2/.twonkymedia ¦Vlogfile /mnt/HD/HD_a2/.twonkymedia/twonkymedia-log.txt Daemonizing... Detaching from parent Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.151.214 port = 49154 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.151.214:49154/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized Starting atopacctd cannot switch on process accounting: Function not implemented Starting atop system monitor atop atop started *** APKG Daemon is starting ... *** sh: you need to specify whom to kill 160624 10:33:48 mysqld_safe Logging to '/mnt/HD_a4/.@database@/WDMyCloudMirror.err'. killall: smbd: no process killed Starting wdnotifier Advertisements Sent LOCK itunes.sh Touch itunes tmp file sh: you need to specify whom to kill 160624 10:33:48 mysqld_safe Starting mysqld daemon with databases from /mnt/HD_a4/.@database@ sh: you need to specify whom to kill wdnotifier started mt-daapd started..... UNLOCK itunes.sh Starting wdmcserver Starting wdphotodbmerger WDPhotodbmerger started 0 Fri Jun 24 10:33:51 PDT 2016 /etc/init.d/onbrdnetloccommd - Start killall: smbd: no process killed cp: can't stat '/etc/NAS_CFG/ftp.xml': No such file or directory cp: can't stat '/etc/NAS_CFG/ftp.xml': No such file or directory killall: chk_blockip: no process killed killall: chk_blockip: no process killed sysinfod: full update begin... mdadm: No md superblock detected on /dev/sda2. mdadm: No md superblock detected on /dev/sdb2. 4160 root 4224 S avahi-daemon: running [WDMyCloudMirror.local] killall: elephantdriveDaemon: no process killed Setting up docker Loading ipv6 NET: Registered protocol family 10 Loading drivers Loading /usr/local/modules/driver/nf_conntrack.ko nf_conntrack version 0.5.0 (8034 buckets, 32136 max) Loading /usr/local/modules/driver/nf_nat.ko Loading /usr/local/modules/driver/nf_defrag_ipv4.ko Loading /usr/local/modules/driver/nf_conntrack_ipv4.ko Loading /usr/local/modules/driver/nf_nat_ipv4.ko Loading /usr/local/modules/driver/x_tables.ko Loading /usr/local/modules/driver/xt_conntrack.ko Loading /usr/local/modules/driver/xt_addrtype.ko Loading /usr/local/modules/driver/xt_tcpudp.ko Loading /usr/local/modules/driver/xt_nat.ko Loading /usr/local/modules/driver/ipt_MASQUERADE.ko Loading /usr/local/modules/driveip_tables: (C) 2000-2006 Netfilter Core Team r/ip_tables.ko Loading /usr/local/modules/driver/iptable_filter.ko Loading /usr/local/modules/driver/iptable_nat.ko Loading /usr/local/modules/driver/llc.ko Loading /usr/local/modules/driver/stp.ko Loading /usr/local/modules/driver/bridge.ko Bridge firewalling registered Setting up cgroup Get http:///var/run/docker.sock/v1.19/containers/json: dial unix /var/run/docker.sock: no such file or directory. Are you trying to connect to a TLS-enabled daemon without TLS? wdappmgr_auto_start finished modifying wd apps exit code Starting Docker umount: /mnt/HD/HD_a2/Nas_Prog/_docker/devicemapper: not mounted Total RAM: 514176 KB Creating /sys/fs/cgroup/memory/docker Docker quota: 171392 KB Set memory quota for docker: 175505408 Docker pid 6018 Stopping wdappmgr wdappmgr is already stopped Starting wdappmgr parent exiting! wdappmgr started bio: create slab <bio-2> at 2 % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 2 100 2 0 0 78 0 --:--:-- --:--:-- --:--:-- 80 wdappmgr_auto_start done ### sata_reload_application end ### Create USB dev node rm: can't remove '/tmp/disk_uuid': No such file or directory sysinfod: full update begin... LED_POWER_ON sysinfod: inform: all drives status=Healthy. mdadm: No md superblock detected on /dev/sda2. mdadm: No md superblock detected on /dev/sdb2. starting pid 4838, tty '/dev/ttyS0': '/bin/login' Password of admin: BusyBox v1.20.2 (2014-10-30 15:28:59 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. root@WDMyCloudMirror / #
Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=1 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:20:0d:40 eth1mtu=1500 eth2addr=00:50:43:20:dc:40 eth2mtu=1500 eth3addr=00:50:43:0d:dc:20 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:dc:0d:40 ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:40:dc:20 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3209/524284 bytes
Marvell>> help ? - alias for 'help' Creset - Creset - Run 'reset' or boot command in a loop, while counting. SatR - Sample At Reset sub-system active_units- print active units on board base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' boot_menu- command allows to select boot script from boot device example: boot_menu bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bootz - boot Linux zImage image from memory bubt - bubt - Burn an image on the Boot Nand Flash. chpart - change active partition cmp - memory compare coninfo - print console devices and information cp - memory copy crc32 - checksum calculation date - get/set/reset date & time ddrPhyRead- ddrPhyRead - Read DDR PHY register ddrPhyWrite- ddrPhyWrite - Write DDR PHY register dhcp - boot image via network using DHCP/TFTP protocol diskboot- diskboot- boot from IDE device dma - dma - Perform DMA using the XOR engine echo - echo args to console editenv - edit environment variable eeprom - EEPROM sub-system env - environment handling commands exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) ext4write- create a file in the root directory false - do nothing, unsuccessfully fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fdt - flattened device tree utility commands fsinfo - print information about filesystems fsload - load binary file from a filesystem image go - start application at address 'addr' help - print command description/usage i2c - I2C sub-system ide - ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image ir - ir - reading and changing MV internal register values. itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range ls - list files in a directory (default /) map - map - Display address decode windows md - memory display me - me - PCIe master enable mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mp - mp - map PCIe BAR mtdparts- define flash/nand partitions mtest - simple RAM read/write test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol nm - memory modify (constant address) pci - list and access PCI Configuration Space pciePhyRead- phyRead - Read PCI-E Phy register pciePhyWrite- pciePhyWrite - Write PCI-E Phy register phyRead - phyRead - Read Phy register phyWrite- phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables pxe - commands to get and boot from pxe files rcvr - rcvr - Start recovery process (with TFTP server) reset - Perform RESET of the CPU resetenv- resetenv - Erase environment sector to reset all variables to default. run - run commands in an environment variable scsi - SCSI sub-system scsiboot- boot from SCSI device se - se - PCIe Slave enable setenv - set environment variables sg - sg - scanning the PHYs status showvar - print local hushshell variables sleep - delay execution for some time source - run script from memory sp - scan and detect all devices on PCI-e interface stage_boot- command to load script/image from different devices example: stage_boot hd_img pxe sys_restore- sys_restore - Search for install script on USB DOK and start installation of linux kernel and rootfs. sysboot - command to get and boot from syslinux files temp - temp - Display the device temperature. tempCmd0- tempCmd - This command allocated for monitor extinction tempCmd1- tempCmd - This command allocated for monitor extinction tempCmd2- tempCmd - This command allocated for monitor extinction tempCmd3- tempCmd - This command allocated for monitor extinction test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol training- training - prints the results of the DDR3 Training. trainingStability- training - prints the results of the DDR3 Training. true - do nothing, successfully ts_report- ts_report - report touch screen coordinate ts_test - ts_test - test touch screen ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume ubifsumount- unmount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor, compiler and linker version whoAmI - - reading CPU ID
Marvell>> version U-Boot 2013.01_v1.03 (Jul 30 2015 - 11:39:08) Marvell version: 2014_T3.0p6 arm-marvell-linux-gnueabi-gcc (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) 4.6.4 GNU ld (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) 2.22.0.20120801 Marvell>> bdinfo arch_number = 0x00000210 boot_params = 0x00000100 DRAM bank = 0x00000000 -> start = 0x00000000 -> size = 0x20000000 DRAM bank = 0x00000001 -> start = 0x00000000 -> size = 0x00000000 ethaddr = 00:50:43:6c:28:27 ip_addr = 192.168.151.232 baudrate = 115200 bps TLB addr = 0x1FFF0000 relocaddr = 0x1FECE000 reloc off = 0x1FECE000 irq_sp = 0x1F9CDF30 sp start = 0x1F9CDF20 FB base = 0x00000000 Marvell>> coninfo List of available devices: serial 80000003 SIO stdin stdout stderr Marvell>> fsinfo ### filesystem type is JFFS2 Scanning JFFS2 FS: done. Compression: NONE frag count: 0 compressed sum: 0 uncompressed sum: 0 Compression: ZERO frag count: 0 compressed sum: 0 uncompressed sum: 0 Compression: RTIME frag count: 0 compressed sum: 0 uncompressed sum: 0 Compression: RUBINMIPS frag count: 0 compressed sum: 0 uncompressed sum: 0 Compression: COPY frag count: 0 compressed sum: 0 uncompressed sum: 0 Compression: DYNRUBIN frag count: 0 compressed sum: 0 uncompressed sum: 0 Compression: ZLIB frag count: 0 compressed sum: 0 uncompressed sum: 0 Marvell>> map CPU Interface ------------- SDRAM_CS0 ....base 000000000, size 512MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable DEVICE_CS0 ....no such DEVICE_CS1 ....no such DEVICE_CS2 ....no such DEVICE_CS3 ....no such PEX0_MEM ....base 0e0000000, size 32MB PEX0_IO ....no such PEX1_MEM ....base 0e2000000, size 32MB PEX1_IO ....no such PEX2_MEM ....base 0e4000000, size 32MB PEX2_IO ....no such PEX3_MEM ....base 0e6000000, size 32MB PEX3_IO ....no such INTER_REGS ....base 0f1000000, size 1MB DMA_UART ....no such SPI0_CS0 ....no such SPI0_CS1 ....no such SPI0_CS2 ....no such SPI0_CS3 ....no such SPI1_CS0 ....no such SPI1_CS1 ....no such SPI1_CS2 ....no such SPI1_CS3 ....no such BOOT_ROM_CS ....no such DEV_BOOTCS ....base 0fd000000, size 16MB CRYPT1_ENG ....no such CRYPT2_ENG ....no such PNC_BM ....no such PSS_PORTS ....no such NSS_MAC_NIC ....no such NSS_MGMT ....no such AHB To MBUS Bridge: ------------------- win0 - PEX0_MEM base e0000000, ....size 32MB win1 - PEX1_MEM base e2000000, ....size 32MB win2 - PEX2_MEM base e4000000, ....size 32MB win3 - PEX3_MEM base e6000000, ....size 32MB win4 - disable win5 - disable win6 - disable win7 - disable win8 - disable win9 - DEV_BOOTCS base fd000000, ....size 16MB win10 - disable win11 - disable win12 - disable win13 - disable win14 - disable win15 - disable win16 - disable win17 - disable win18 - disable win19 - disable win20 - INTER_REGS base f1000000, ....size 1MB PEX0: ----- Pex Bars Internal Regs Bar0.... base f1000000, size 1MB DRAM Bar1............. base 00000000, size 512MB Devices Bar2.......... disable Pex Decode Windows win0 - SDRAM_CS0 base 00000000, ....size 512MB win1 - disable win2 - disable win3 - disable win4 - disable win5 - disable default win - SDRAM_CS0 Expansion ROM - SDRAM_CS0 USB 0: ---- win0 - SDRAM_CS0 base 00000000, ....size 512MB win1 - PEX0_MEM base e0000000, ....size 32MB win2 - disable win3 - disable win4 - mvUsbWinRead (dev=0): ERR. Invalid winNum 4 win5 - mvUsbWinRead (dev=0): ERR. Invalid winNum 5 win6 - mvUsbWinRead (dev=0): ERR. Invalid winNum 6 win7 - mvUsbWinRead (dev=0): ERR. Invalid winNum 7 win8 - mvUsbWinRead (dev=0): ERR. Invalid winNum 8 win9 - mvUsbWinRead (dev=0): ERR. Invalid winNum 9 win10 - mvUsbWinRead (dev=0): ERR. Invalid winNum 10 win11 - mvUsbWinRead (dev=0): ERR. Invalid winNum 11 win12 - mvUsbWinRead (dev=0): ERR. Invalid winNum 12 win13 - mvUsbWinRead (dev=0): ERR. Invalid winNum 13 win14 - mvUsbWinRead (dev=0): ERR. Invalid winNum 14 win15 - mvUsbWinRead (dev=0): ERR. Invalid winNum 15 ETH 0: ---- win0 - SDRAM_CS0 base 00000000, ....size 512MB win1 - disable win2 - disable win3 - disable win4 - disable win5 - disable win6 - mvNetaWinGet: ERR. Invalid winNum 6 win7 - mvNetaWinGet: ERR. Invalid winNum 7 win8 - mvNetaWinGet: ERR. Invalid winNum 8 win9 - mvNetaWinGet: ERR. Invalid winNum 9 win10 - mvNetaWinGet: ERR. Invalid winNum 10 win11 - mvNetaWinGet: ERR. Invalid winNum 11 win12 - mvNetaWinGet: ERR. Invalid winNum 12 win13 - mvNetaWinGet: ERR. Invalid winNum 13 win14 - mvNetaWinGet: ERR. Invalid winNum 14 win15 - mvNetaWinGet: ERR. Invalid winNum 15 ETH 1: ---- win0 - SDRAM_CS0 base 00000000, ....size 512MB win1 - disable win2 - disable win3 - disable win4 - disable win5 - disable win6 - mvNetaWinGet: ERR. Invalid winNum 6 win7 - mvNetaWinGet: ERR. Invalid winNum 7 win8 - mvNetaWinGet: ERR. Invalid winNum 8 win9 - mvNetaWinGet: ERR. Invalid winNum 9 win10 - mvNetaWinGet: ERR. Invalid winNum 10 win11 - mvNetaWinGet: ERR. Invalid winNum 11 win12 - mvNetaWinGet: ERR. Invalid winNum 12 win13 - mvNetaWinGet: ERR. Invalid winNum 13 win14 - mvNetaWinGet: ERR. Invalid winNum 14 win15 - mvNetaWinGet: ERR. Invalid winNum 15 ETH 2: ---- win0 - SDRAM_CS0 base 00000000, ....size 512MB win1 - disable win2 - disable win3 - disable win4 - disable win5 - disable win6 - mvNetaWinGet: ERR. Invalid winNum 6 win7 - mvNetaWinGet: ERR. Invalid winNum 7 win8 - mvNetaWinGet: ERR. Invalid winNum 8 win9 - mvNetaWinGet: ERR. Invalid winNum 9 win10 - mvNetaWinGet: ERR. Invalid winNum 10 win11 - mvNetaWinGet: ERR. Invalid winNum 11 win12 - mvNetaWinGet: ERR. Invalid winNum 12 win13 - mvNetaWinGet: ERR. Invalid winNum 13 win14 - mvNetaWinGet: ERR. Invalid winNum 14 win15 - mvNetaWinGet: ERR. Invalid winNum 15 XOR 0: ---- win0 - SDRAM_CS0 base 00000000, ....size 512MB win1 - PEX0_MEM base e0000000, ....size 32MB win2 - PEX1_MEM base e2000000, ....size 32MB win3 - PEX2_MEM base e4000000, ....size 32MB win4 - PEX3_MEM base e6000000, ....size 32MB win5 - disable win6 - disable win7 - disable win8 - win9 - win10 - win11 - win12 - win13 - win14 - win15 - XOR 1: ---- win0 - SDRAM_CS0 base 00000000, ....size 512MB win1 - PEX0_MEM base e0000000, ....size 32MB win2 - PEX1_MEM base e2000000, ....size 32MB win3 - PEX2_MEM base e4000000, ....size 32MB win4 - PEX3_MEM base e6000000, ....size 32MB win5 - disable win6 - disable win7 - disable win8 - win9 - win10 - win11 - win12 - win13 - win14 - win15 - Sata 0: ---- win0 - SDRAM_CS0 base 00000000, ....size 512MB win1 - disable win2 - disable win3 - disable win4 - mvSata3WinRead (dev=0): ERR. Invalid winNum 4 win5 - mvSata3WinRead (dev=0): ERR. Invalid winNum 5 win6 - mvSata3WinRead (dev=0): ERR. Invalid winNum 6 win7 - mvSata3WinRead (dev=0): ERR. Invalid winNum 7 win8 - mvSata3WinRead (dev=0): ERR. Invalid winNum 8 win9 - mvSata3WinRead (dev=0): ERR. Invalid winNum 9 win10 - mvSata3WinRead (dev=0): ERR. Invalid winNum 10 win11 - mvSata3WinRead (dev=0): ERR. Invalid winNum 11 win12 - mvSata3WinRead (dev=0): ERR. Invalid winNum 12 win13 - mvSata3WinRead (dev=0): ERR. Invalid winNum 13 win14 - mvSata3WinRead (dev=0): ERR. Invalid winNum 14 win15 - mvSata3WinRead (dev=0): ERR. Invalid winNum 15 Sata 1: ---- win0 - # it stopped here and needed a hardreset
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 11, 2016 04:00AM |
Admin Registered: 13 years ago Posts: 19,104 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 11, 2016 04:16AM |
Registered: 9 years ago Posts: 19 |
dhcp; setenv serverip 192.168.151.4; tftp 0xa00000 uImage; tftp 0xf00000 uRamdisk; bootm 0xa00000 0xf00000It works, but there is a problem with the network interface, so i can't connect to the box via ssh or http...:
Marvell>> dhcp BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 42 *** Unhandled DHCP Option in OFFER/ACK: 42 DHCP client bound to address 192.168.151.227 Marvell>> setenv serverip 192.168.151.4; tftp 0xa00000 uImage; tftp 0xf00000 uRamdisk; bootm 0xa00000 0xf00000 Using egiga2 device TFTP from server 192.168.151.4; our IP address is 192.168.151.227 Filename 'uImage'. Load address: 0xa00000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################ 1.5 MiB/s done Bytes transferred = 4882732 (4a812c hex) Using egiga2 device TFTP from server 192.168.151.4; our IP address is 192.168.151.227 Filename 'uRamdisk'. Load address: 0xf00000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### 2 MiB/s done Bytes transferred = 2682706 (28ef52 hex) ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux Created: 2016-06-25 12:03:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4882668 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Ramdisk Created: 2016-06-25 10:57:34 UTC Image Type: ARM Linux RAMDisk Image (lzma compressed) Data Size: 2682642 Bytes = 2.6 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (root@buildserver-x86) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #1 SMP Sat Jun 25 17:02:43 YEKT 2016 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 8 pages/cpu @c1698000 s8576 r8192 d16000 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129792 Kernel command line: root=/dev/ram console=ttyS0,115200 PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) allocated 1048576 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 512MB = 512MB total Memory: 505324k/505324k available, 18964k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0889124 (8709 kB) .init : 0xc088a000 - 0xc08ca180 ( 257 kB) .data : 0xc08cc000 - 0xc09212a0 ( 341 kB) .bss : 0xc09212a0 - 0xc096f23c ( 312 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p5 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc0684238 - 0xc0684290 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (5311.69 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 xor: measuring software checksum speed arm4regs : 2361.600 MB/sec 8regs : 1594.800 MB/sec 32regs : 1360.000 MB/sec xor: using function: arm4regs (2361.600 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ196, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ228, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 169 MB/s raid6: int32x2 245 MB/s raid6: int32x4 311 MB/s raid6: int32x8 316 MB/s raid6: using algorithm int32x8 (316 MB/s) raid6: using intx1 recovery algorithm mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Switching to clocksource armada_370_xp_clocksource cfg80211: Calling CRDA to update world regulatory domain FS-Cache: Loaded NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 2612K (c0f01000 - c118e000) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). FS-Cache: Netfs 'cifs' registered for caching Key type cifs.idmap registered SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 992 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC Nand Flash Timing = [WP : 12], [WH : 10] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 8 ofpart partitions found on MTD device armada-nand Creating 8 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "U-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "uRamdisk" 0x000000f00000-0x00000c800000 : "image.cfs" 0x00000c800000-0x00000d700000 : "rescue fw" 0x00000d700000-0x00000eb00000 : "config" 0x00000eb00000-0x00000f500000 : "reserve1" 0x00000f500000-0x00000ff00000 : "reserve2" bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) SoC: model = 0x6820, revision = 0x4 mvPncVirtBase = 0xe1c00000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=2 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 3, GbE port = 0 giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) port #1: is_sgmii=0, is_rgmii=1, phy_addr=1 o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048 o Port 1 is connected to Linux netdevice o eth1, ifindex = 4, GbE port = 1 giga p=1: mtu=1500, mac=00:50:43:02:02:02 (platform) port #2: is_sgmii=1, is_rgmii=0, phy_addr=0 o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 o Port 2 is connected to Linux netdevice o eth2, ifindex = 5, GbE port = 2 giga p=2: mtu=1500, mac=00:50:43:02:02:03 (platform) libphy: orion_mdio_bus: probed mdio_bus f1072004.mdio-mi: cannot get PHY at address 2 mdio_bus f1072004.mdio-mi: cannot get PHY at address 1 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata2.00: ATA-8: Hitachi HDS5C3020ALA632, ML6OAA10, max UDMA/133 ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: ATA-8: Hitachi HDS5C3020ALA632, ML6OAA10, max UDMA/133 ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 ML6O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Direct-Access ATA Hitachi HDS5C302 ML6O PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sdb4 sd 1:0:0:0: [sdb] Attached SCSI disk sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c08a9e9c) Netfilter messages via NETLINK v0.30. nfnl_acct: registering with nfnetlink. nf_conntrack version 0.5.0 (7936 buckets, 31744 max) arp_tables: (C) 2002 David S. Miller TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 registered taskstats version 1 mvebu-rtc f10a3800.rtc: setting system clock to 2016-07-10 10:36:18 UTC (1468146978) Freeing unused kernel memory: 256K (c088a000 - c08ca000) # Loading, please wait... # Mounting filesystems... # Runing a shell... pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added eth0: link up eth0: started udhcpc (v1.24.1) started Setting IP address 0.0.0.0 on eth0 Sending discover... Sending discover... Sending discover... No lease, failing / #
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 11, 2016 08:53AM |
Admin Registered: 13 years ago Posts: 19,104 |
ide reset ext2ls ide 0:1 /
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 11, 2016 01:31PM |
Registered: 9 years ago Posts: 19 |
Marvell>> ide reset Reset IDE: Marvell Serial ATA Adapter no device found
Marvell>> ext2ls ide 0:1 / ** Bad device ide 0 **:-(
Marvell>> active_units Active: cpu0, cpu1, pex0, egiga0, egiga1, egiga2, usb0, usb1, usb2, nand, i2c0
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 11, 2016 01:40PM |
Admin Registered: 13 years ago Posts: 19,104 |
usb start
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 17, 2016 03:16AM |
Registered: 9 years ago Posts: 19 |
Marvell>> usb start (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 18, 2016 03:38AM |
Admin Registered: 13 years ago Posts: 19,104 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 21, 2016 07:19AM |
Registered: 9 years ago Posts: 19 |
Marvell>> setenv usbActive 1 Marvell>> usb start (Re)start USB... USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>> usb info 1: Hub, USB Revision 3.0 - u-boot XHCI Host Controller - Class: Hub - PacketSize: 9 Configurations: 1 - Vendor: 0x0000 Product 0x0000 Version 1.0 Configuration: 1 - Interfaces: 1 Self Powered 0mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms 2: Mass Storage, USB Revision 3.0 - USB DISK 15071003007159 - Class: (from Interface) Mass Storage - PacketSize: 9 Configurations: 1 - Vendor: 0x1f75 Product 0x0917 Version 0.1 Configuration: 1 - Interfaces: 1 Bus Powered 76mA Interface: 0 - Alternate Setting 0, Endpoints: 2 - Class Mass Storage, Transp. SCSI, Bulk only - Endpoint 2 Out Bulk MaxPacket 1024 - Endpoint 1 In Bulk MaxPacket 1024
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 21, 2016 02:28PM |
Admin Registered: 13 years ago Posts: 19,104 |
> Marvell>> setenv usbActive 1 > Marvell>> usb start > (Re)start USB... > USB0: Port (usbActive) : 1 Interface (usbType > = 3) : USB XHCI 1.00 > scanning bus 0 for devices... 2 USB Device(s) > found > scanning usb for storage devices... 1 > Storage Device(s) found > scanning usb for ethernet devices... 0 > Ethernet Device(s) found > Marvell>> usb info > 1: Hub, USB Revision 3.0 > - u-boot XHCI Host Controller > - Class: Hub > - PacketSize: 9 Configurations: 1 > - Vendor: 0x0000 Product 0x0000 Version 1.0 > Configuration: 1 > - Interfaces: 1 Self Powered 0mA > Interface: 0 > - Alternate Setting 0, Endpoints: 1 > - Class Hub > - Endpoint 1 In Interrupt MaxPacket 8 > Interval 255ms > > 2: Mass Storage, USB Revision 3.0 > - USB DISK 15071003007159 > - Class: (from Interface) Mass Storage > - PacketSize: 9 Configurations: 1 > - Vendor: 0x1f75 Product 0x0917 Version 0.1 > Configuration: 1 > - Interfaces: 1 Bus Powered 76mA > Interface: 0 > - Alternate Setting 0, Endpoints: 2 > - Class Mass Storage, Transp. SCSI, Bulk > only > - Endpoint 2 Out Bulk MaxPacket 1024 > - Endpoint 1 In Bulk MaxPacket 1024 >>
ext2ls usb 0:1 /
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 21, 2016 03:19PM |
Registered: 9 years ago Posts: 19 |
Marvell>> fatls usb 0:1 / 22851472 mbam-setup-2.2.1.1043.exe 1399 malwarescanreport.txt autoruns/ processexplorer/ system volume information/ 4883863 uimage 2682706 uramdisk 4 file(s), 3 dir(s)after
ext2ls usb 0:1 /brought me a system halt...
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 21, 2016 04:06PM |
Admin Registered: 13 years ago Posts: 19,104 |
ext2ls usb 0:1 /
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 21, 2016 06:10PM |
Registered: 9 years ago Posts: 19 |
> ext2ls usb 0:1 /I'll do that later.
Marvell>> setenv usbActive 1 Marvell>> usb start (Re)start USB... USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>> fatload usb 0:1 0xa00000 uImage; fatload usb 0:1 0xf00000 uRamdisk reading uImage 4883863 bytes read in 85 ms (54.8 MiB/s) reading uRamdisk 2682706 bytes read in 59 ms (43.4 MiB/s) Marvell>> bootm 0xa00000 0xf00000 ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux Created: 2016-07-18 17:06:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4883799 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Ramdisk Created: 2016-06-25 10:57:34 UTC Image Type: ARM Linux RAMDisk Image (lzma compressed) Data Size: 2682642 Bytes = 2.6 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum ... OKDo you have any idea, why the system halts here?
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 21, 2016 10:08PM |
Admin Registered: 13 years ago Posts: 19,104 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 27, 2016 04:09PM |
Registered: 9 years ago Posts: 19 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 27, 2016 04:54PM |
Admin Registered: 13 years ago Posts: 19,104 |
Quote
Marvell>> fatls usb 0:1 /
22851472 mbam-setup-2.2.1.1043.exe
1399 malwarescanreport.txt
autoruns/
processexplorer/
system volume information/
4883863 uimage
2682706 uramdisk
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) July 28, 2016 05:23AM |
Registered: 9 years ago Posts: 19 |
See above: not the content of the USB-thumbdrive is the rootfs; it is in uramdisk...Quote
Marvell>> fatls usb 0:1 /
> 22851472 mbam-setup-2.2.1.1043.exe
> 1399 malwarescanreport.txt
> autoruns/
> processexplorer/
> system volume information/
> 4883863 uimage
> 2682706 uramdisk
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) September 13, 2016 01:00AM |
Registered: 10 years ago Posts: 143 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) September 14, 2016 03:05AM |
Registered: 9 years ago Posts: 19 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) September 14, 2016 03:23AM |
Registered: 10 years ago Posts: 143 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) September 21, 2016 02:05AM |
Registered: 10 years ago Posts: 143 |
"1" is the Key thats interrupting the bootprocess :-)Quote
Hitting a key didn't interrupt the bootprocess, but shortening RX and TX did. This is the factory preset environment:
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) September 25, 2016 11:42AM |
Registered: 10 years ago Posts: 143 |
peacemaker@debianvm:/media/data/linux-4.6.7$ make -j8 zImage armada-385-ex2.dtb CHK include/config/kernel.release CHK include/generated/uapi/linux/version.h CHK include/generated/utsrelease.h DTC arch/arm/boot/dts/armada-385-ex2.dtb ERROR (duplicate_property_names): Duplicate property name status in /soc/internal-regs/nand@d0000 ERROR: Input tree has errors, aborting (use -f to force output) scripts/Makefile.lib:307: die Regel für Ziel „arch/arm/boot/dts/armada-385-ex2.dtb“ scheiterte make[1]: *** [arch/arm/boot/dts/armada-385-ex2.dtb] Fehler 2 arch/arm/Makefile:334: die Regel für Ziel „armada-385-ex2.dtb“ scheiterte make: *** [armada-385-ex2.dtb] Fehler 2
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) October 01, 2016 12:53PM |
Registered: 10 years ago Posts: 143 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) October 24, 2016 03:54PM |
Registered: 10 years ago Posts: 143 |
MM
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) November 16, 2016 02:00PM |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) November 16, 2016 03:09PM |
Registered: 10 years ago Posts: 143 |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) November 22, 2016 02:53PM |
Registered: 10 years ago Posts: 143 |
sudo tar -xJvf MCMgen2-jessie-basic-armhf.tar.xz sync
set ipaddr 192.168.0.180; set serverip 192.168.0.104; tftp 1200000 uImage-4.8.6_ex2u tftp 2000000 uInitrd; bootm 0x1200000 0x2000000
hostname: WDebian user: root passwd: root
MM
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) November 28, 2016 11:40AM |
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) November 28, 2016 12:54PM |
Registered: 10 years ago Posts: 143 |
MM
Re: WD MyCloud Mirror Gen2 (BWVZ, GrandTeton) November 28, 2016 01:34PM |