Re: Debian on CISCO ON100-K9 August 13, 2016 06:59PM |
Admin Registered: 13 years ago Posts: 18,591 |
Re: Debian on CISCO ON100-K9 August 13, 2016 07:13PM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 August 14, 2016 03:49AM |
Admin Registered: 13 years ago Posts: 18,591 |
Re: Debian on CISCO ON100-K9 August 14, 2016 12:43PM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 August 14, 2016 03:40PM |
Admin Registered: 13 years ago Posts: 18,591 |
Re: Debian on CISCO ON100-K9 August 14, 2016 05:52PM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 August 14, 2016 06:09PM |
Admin Registered: 13 years ago Posts: 18,591 |
Re: Debian on CISCO ON100-K9 August 15, 2016 12:29AM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 August 18, 2016 03:12AM |
Admin Registered: 13 years ago Posts: 18,591 |
kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2016.05-tld-2.1.on100_k9.mtd0.kwb -p
Re: Debian on CISCO ON100-K9 August 18, 2016 02:32PM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 August 18, 2016 03:09PM |
Admin Registered: 13 years ago Posts: 18,591 |
Quote
Important Note: If possible, try to test this boot image with UART booting before flashing to NAND. See davygravy's UART booting using kwboot instruction here in this thread. The latest u-boot image released here should be used for UART booting, if your box is the type that supports it (these do not: Dockstar, Pogo E02, iConnect).
Re: Debian on CISCO ON100-K9 August 18, 2016 03:11PM |
Registered: 8 years ago Posts: 298 |
Re: Debian on CISCO ON100-K9 August 18, 2016 07:58PM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 August 19, 2016 12:36AM |
Registered: 9 years ago Posts: 442 |
> kwboot -t -B 115200 /dev/ttyUSB0 -b > uboot.2016.05-tld-2.1.on100_k9.mtd0.kwb -p >>
99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-2.1 (Aug 18 2016 - 01:44:47 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0, egiga1 Error: egiga1 address not set. MV88E1310 PHY initialized on egiga0 Hit any key to stop autoboot: 0 ON100_K9> ping 192.168.11.1 *** ERROR: `ipaddr' not set ping failed; host 192.168.11.1 is not alive ON100_K9> setenv ipaddr 192.168.11.100 ON100_K9> ping 192.168.11.1 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.11.1 is not alive ON100_K9>
Re: Debian on CISCO ON100-K9 August 19, 2016 01:38AM |
Admin Registered: 13 years ago Posts: 18,591 |
Quote
> I did notice that this has egiga0 and egaga1
> switched from what stock U-Boot identifies. Your
> U-Boot identifies the MON port as egiga0 device
> while stock identifies the LAN port as egiga0.
Re: Debian on CISCO ON100-K9 August 19, 2016 10:10PM |
Admin Registered: 13 years ago Posts: 18,591 |
Quote
> I did notice that this has egiga0 and
> egaga1
> > switched from what stock U-Boot identifies.
> Your
> > U-Boot identifies the MON port as egiga0 device
> > while stock identifies the LAN port as
> egiga0.
Re: Debian on CISCO ON100-K9 August 20, 2016 02:55AM |
Admin Registered: 13 years ago Posts: 18,591 |
ping <router ip> usb start mmc rescan
Re: Debian on CISCO ON100-K9 August 20, 2016 05:30PM |
Registered: 9 years ago Posts: 442 |
> ping <router ip> > usb start > mmc rescan >
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Feb 22 2011 - 14:06:09) Marvell version: 3.5.9 - Cisco Plasma U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D2340 Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:512 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled Module 0 is RGMII USB 0: host mode PEX 0: interface detected no Link. PEX 1: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Plasma>> ping 192.168.11.1 Using egiga0 device host 192.168.11.1 is alive Plasma>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Plasma>> mmc rescan Usage: mmcinit - init mmc card Plasma>> mmcinit SDHC found. Card desciption is: Manufacturer: 0x27, OEM "PH" Product name: "SD04G", revision 2.0 Serial number: 2084250414 Manufacturing date: 10/2010 Capacity : 3796 MB Total blocks: 7774208 ( 512 bytes per block) CRC: 0x00, b0 = 0 Plasma>>
[Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-2.2 (Aug 20 2016 - 00:24:37 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0, egiga1 Error: egiga1 address not set. MV88E1310 PHY initialized on egiga0 PHY reset timed out MV88E1310 PHY initialized on egiga1 Hit any key to stop autoboot: 0 ON100_K9> ping 192.168.11.1 No link on egiga0 *** ERROR: `ipaddr' not set ping failed; host 192.168.11.1 is not alive ON100_K9> usb start starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found ON100_K9> mmc rescan Unknown command 'mmc' - try 'help' ON100_K9> help mmc Unknown command 'mmc' - try 'help' without arguments for list of all known commands ON100_K9> setenv ipaddr 192.168.11.100 ON100_K9> ping 192.168.11.1 *** ERROR: `eth1addr' not set ping failed; host 192.168.11.1 is not alive ON100_K9> setenv eth1addr 64:00:F1:20:DF:66 ON100_K9> ping 192.168.11.1 Using egiga1 device ARP Retry count exceeded; starting again ping failed; host 192.168.11.1 is not alive ON100_K9>
Re: Debian on CISCO ON100-K9 August 20, 2016 06:09PM |
Admin Registered: 13 years ago Posts: 18,591 |
Now same setup but using kwboot with your latest uboot file. This time Link and Act lites are on for the MON port and Act is on for the LAN port. Other lites are the same as with stock U-Boot.
ON100_K9> setenv eth1addr 64:00:F1:20:DF:66 ON100_K9> ping 192.168.11.1 Using egiga1 device
PHY reset timed out
Re: Debian on CISCO ON100-K9 August 20, 2016 06:37PM |
Registered: 9 years ago Posts: 442 |
> Now same setup but using kwboot with your latest > uboot file. This time Link and Act lites are on > for the MON port and Act is on for the LAN port. > Other lites are the same as with stock U-Boot. >>
> ON100_K9> setenv eth1addr 64:00:F1:20:DF:66 > ON100_K9> ping 192.168.11.1 > Using egiga1 device >>
Re: Debian on CISCO ON100-K9 August 20, 2016 10:51PM |
Registered: 9 years ago Posts: 442 |
Re: Debian on CISCO ON100-K9 August 21, 2016 02:13AM |
Admin Registered: 13 years ago Posts: 18,591 |
Re: Debian on CISCO ON100-K9 August 23, 2016 11:53PM |
Registered: 9 years ago Posts: 1,516 |
root@debian:/usr/local/bin# ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2016.05-tld-2.2.on100_k9.mtd0.kwb -p
Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. >ping 192.168.178.110 Pinging 192.168.178.110 with 32 bytes of data: Reply from 192.168.178.110: bytes=32 time<1ms TTL=64 Reply from 192.168.178.110: bytes=32 time<1ms TTL=64 Reply from 192.168.178.110: bytes=32 time<1ms TTL=64 Reply from 192.168.178.110: bytes=32 time<1ms TTL=64 Ping statistics for 192.168.178.110: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms 7x64>
Re: Debian on CISCO ON100-K9 August 25, 2016 02:41AM |
Admin Registered: 13 years ago Posts: 18,591 |
Re: Debian on CISCO ON100-K9 August 25, 2016 09:53AM |
Registered: 9 years ago Posts: 1,037 |
Re: Debian on CISCO ON100-K9 August 25, 2016 11:22AM |
Registered: 9 years ago Posts: 39 |
Re: Debian on CISCO ON100-K9 August 25, 2016 03:09PM |
Registered: 9 years ago Posts: 442 |
Re: Debian on CISCO ON100-K9 August 25, 2016 03:33PM |
Admin Registered: 13 years ago Posts: 18,591 |
Re: Debian on CISCO ON100-K9 August 25, 2016 04:05PM |
Registered: 8 years ago Posts: 298 |
Re: Debian on CISCO ON100-K9 August 25, 2016 04:30PM |
Registered: 9 years ago Posts: 1,516 |
root@debian:/usr/local/bin# ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2016.05-tld-2.3.on100_k9.mtd0.kwb -p Sending boot message. Please reboot the target...|
### JFFS2 loading 'boot.img' to 0x400000 Scanning JFFS2 FS: . done. ### JFFS2 load complete: 382 bytes loaded to 0x400000 ## Executing script at 00400000 "PLASMA Booting FIRST partition @ 0x400000" NAND read: device 0 offset 0x400000, size 0x600000 Reading data from 0x9ff800 -- 100% complete. 6291456 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.31.8PATCH-29 Created: 2011-06-01 21:56:16 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2323016 Bytes = 2.2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................................................................................... done, booting the kernel. Linux version 2.6.31.8PATCH-29 (jamwyatt@aesop) (gcc version 4.3.2 (sdk3.2rc1-ct-ng-1.4.1) ) #1 Wed Jun 1 16:56:06 CDT 2011 CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 CPU: VIVT data cache, VIVT instruction cache Machine: Feroceon-KW Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping off. Total pages: 130048 Kernel command line: console=ttyS0,115200 max_loop=64 mtdparts=nand_mtd:2m(uBoot)ro,2m(dualboot),6m(kernel1),8m(rootfs1),6m(kernel2),8m(rootfs2),470m(datafs),-(misc) root=/dev/mtdblock3 ro serialNo=DNI15440BHM hwVer=ON100-K9_V01 ip=::::DB88FXX81:eth0:none rootfstype=jffs2 PID hash table entries: 2048 (order: 11, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 256MB 256MB = 512MB total Memory: 510592KB available (4348K code, 315K data, 124K init, 0K highmem) Hierarchical RCU implementation. NR_IRQS:128 Console: colour dummy device 80x30 Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 Feroceon L2: Enabling L2 Feroceon L2: Cache support initialised. CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 256MB SDRAM_CS1 ....base 10000000, size 256MB SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PEX1_MEM ....base e8000000, size 128MB PEX1_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version KW_LSP_5.1.3_patch29)-- DB-88F6282A-BP Soc: 88F6282 A1 LE Detected Tclk 200000000 and SysClk 400000000 MV Buttons Device Load btns_init_data - plasma btns_init_data - Number of configured buttons: 1 Marvell USB EHCI Host controller #0: d0054740 PEX0 interface detected no Link. PEX1 interface detected no Link. PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered NET: Registered protocol family 1 rtc mv_rtc: rtc core: registered kw-rtc as rtc0 RTC registered cpufreq: Init kirkwood cpufreq driver Kirkwood hwmon thermal sensor initialized. XOR registered 4 channels XOR 2nd invalidate WA enabled cesadev_init(c000c990) mvCesaInit: sessions=640, queue=64, pSram=f0000000 Warning: TS unit is powered off. MV Buttons Driver Load JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 997 alg: No test for cipher_null (cipher_null-generic) alg: No test for ecb(cipher_null) (ecb-cipher_null) alg: No test for digest_null (digest_null-generic) alg: No test for compress_null (compress_null-generic) alg: No test for stdrng (krng) alg: No test for hmac(digest_null) (hmac(digest_null-generic)) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler anticipatory registered (default) Initializing ths8200_init Initializing dove_adi9889_init Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A console [ttyS0] enabled loop: module loaded Integrated Sata device found IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o 2 Giga ports supported o Single RX Queue support - ETH_DEF_RXQ=0 o Single TX Queue support - ETH_DEF_TXQ=0 o TCP segmentation offload (TSO) supported o Large Receive offload (LRO) supported o Receive checksum offload supported o Transmit checksum offload supported o Network Fast Processing (Routing) supported - (Disabled) o Driver ERROR statistics enabled o Proc tool API enabled o SKB Reuse supported - (Disabled) o SKB Recycle supported - (Disabled) o Rx descripors: q0=128 o Tx descripors: q0=532 o Loading network interface(s): o register under mv88fx_eth platform o eth0, ifindex = 2, GbE port = 0 o eth1, ifindex = 3, GbE port = 1 mvFpRuleDb (d07f0000): 16384 entries, 65536 bytes Counter=0, opIdx=6, overhead=16 Counter=1, opIdx=2, overhead=0 Counter=2, opIdx=1, overhead=18 Counter=3, opIdx=2, overhead=0 Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI Copyright (c) 1999-2006 Intel Corporation. e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 e1000e: Copyright (c) 1999-2008 Intel Corporation. e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI e100: Copyright(c) 1999-2006 Intel Corporation tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 1471 at 0x00000b7e0000 Bad eraseblock 1911 at 0x00000eee0000 Bad eraseblock 2539 at 0x000013d60000 Bad eraseblock 2854 at 0x0000164c0000 Bad eraseblock 3405 at 0x00001a9a0000 8 cmdlinepart partitions found on MTD device nand_mtd Using command line partition definition Creating 8 MTD partitions on "nand_mtd": 0x000000000000-0x000000200000 : "uBoot" 0x000000200000-0x000000400000 : "dualboot" 0x000000400000-0x000000a00000 : "kernel1" 0x000000a00000-0x000001200000 : "rootfs1" 0x000001200000-0x000001800000 : "kernel2" 0x000001800000-0x000002000000 : "rootfs2" 0x000002000000-0x00001f600000 : "datafs" 0x00001f600000-0x000020000000 : "misc" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.70059: Marvell Orion EHCI ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 usbcore: registered new interface driver ums-usbat mice: PS/2 mouse device common for all mice i2c /dev entries driver Orion Watchdog Timer: Initial timeout 21 sec sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman mmc0: mvsdio driver initialized, lacking card detect (fall back to polling) Registered led device: plasma:green:s1 Registered led device: plasma:red:s1 Registered led device: plasma:green:s2 Registered led device: plasma:red:s2 GRE over IPv4 tunneling driver TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> rtc mv_rtc: setting system clock to 2016-08-26 06:16:39 UTC (1472192199) CLEANMARKER node found at 0x00000000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00020000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00040000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00060000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00080000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x000a0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x000c0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x000e0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00100000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00120000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00140000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00160000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00180000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x001a0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x001c0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x001e0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00200000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00220000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00240000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00260000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00280000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x002a0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x002c0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x002e0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00300000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00320000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00340000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00360000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x00380000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x003a0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x003c0000 has totlen 0xc != normal 0x0 CLEANMARKER node found at 0x003e0000 has totlen 0xc != normal 0x0 VFS: Mounted root (jffs2 filesystem) readonly on device 31:3. Freeing init memory: 124K Creating R/W root Start up on R/W root Root Filesystem Version: 18.45 Set LED STATE to: init_state Linux ON100_6400F120FFB6 2.6.31.8PATCH-29 #1 Wed Jun 1 16:56:06 CDT 2011 eth0: link down eth0: started eth0: link up, full duplex, speed 1 Gbps eth1: started initFinish.sh: Starting HTTPD - Status info now available UBI: attaching mtd6 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd6 to ubi0 UBI: MTD device name: "datafs" UBI: MTD device size: 470 MiB UBI: number of good PEBs: 3755 UBI: number of bad PEBs: 5 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 3755 UBI: number of PEBs reserved for bad PEB handling: 37 UBI: max/mean erase counter: 37/35 UBI: image sequence number: 2124868612 UBI: background thread "ubi_bgt0d" started, PID 749 UBI device number 0, total 3755 LEBs (484485120 bytes, 462.0 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB) initFinish.sh: ubiattach was successful to ubi0 initFinish.sh: mknod was successful for /dev/ubi0 initFinish.sh: Starting mount of internal flash .... ubi0 onto /mnt/INTFLASH UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "datafs" UBIFS: file system size: 477388800 bytes (466200 KiB, 455 MiB, 3700 LEBs) UBIFS: journal size: 23869440 bytes (23310 KiB, 22 MiB, 185 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 4952683 bytes (4836 KiB) initFinish.sh: .... successfully completed mount Set LED STATE to: netconf_active killall: udhcpc: no process killed info, udhcpc (v0.9.9-pre) started debug, Sending discover... debug, Sending select for 192.168.178.110... info, Lease of 192.168.178.110 obtained, lease time 86400 udhcpc.sh: update default gw udhcpc.sh: deleting routes udhcpc.sh: Router is 192.168.178.1 eth0 udhcpc.sh: skip update dns Set LED STATE to: net_complete initFinish.sh: Attempting to mount /dev/sda1 flash device mount: Mounting /dev/sda1 on /mnt/EXTFLASH failed: No such device or address mount: Mounting /dev/sda1 on /mnt/EXTFLASH failed: No such device or address net.ipv4.neigh.eth0.gc_stale_time = 360 net.ipv4.neigh.default.gc_stale_time = 360 net.ipv4.conf.all.arp_filter = 1 vm.swappiness = 0 initFinish.sh: No CRAMFS file, we have run out of options .... failsafe time Set LED STATE to: netconf_active info, udhcpc (v0.9.9-pre) started debug, Sending discover... debug, Sending select for 192.168.178.110... info, Lease of 192.168.178.110 obtained, lease time 86400 udhcpc.sh: update default gw udhcpc.sh: deleting routes udhcpc.sh: Router is 192.168.178.1 eth0 udhcpc.sh: skip update dns Set LED STATE to: net_complete Set LED STATE to: failsafe ap_failSafeUpdate: Beginning fail safe recovery ap_failSafeUpdate: Cleaning up left-over rogue processes ... should already have stopped UBIFS: un-mount UBI device 0, volume 0 ap_failSafeUpdate: Beginning reformat of internal flash .... ubi0 Volumes count: 1 Logical eraseblockUBI: mtd6 is detached from ubi0 size: 129024 bytes, 126.0 KiB Total amount of logical eraseblocks: 3755 (484485120 bytes, 462.0 MiB) Amount of available logical eraseblocks: 0 (0 bytes) Maximum count of volumes 128 Count of bad physical eraseblocks: 5 Count of reserved physical eraseblocks: 37 Current maximum erase counter value: 37 Minimum input/output unit size: 2048 bytes Character device major/minor: 252:0 Present volumes: 0 ap_formatInternalFlash-ON100: Detached the UBI volume from mtd6 ubiformat: mtd6 (nand), size 492830720 bytes (470.0 MiB), 3760 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes libscan: scanning eraseblock 3759 -- 100 % complete ubiformat: 3755 eraseblocks have valid erase counter, mean value is 35 ubiformat: 5 bad eraseblocks found, numbers: 1215, 1655, 2283, 2598, 3149 ubiformat: formatting eraseblock 3748 UBI: attaching mtd6 to ubi0 -- 99 % completeUBI: physical eraseblock size: 131072 bytes (128 KiB) ubiformat: foUBI: logical eraseblock size: 129024 bytes rmatting eraseblUBI: smallest flash I/O unit: 2048 ock 3749 -- 99 %UBI: sub-page size: 512 ubifUBI: VID header offset: 512 (aligned 512) ormat: formattinUBI: data offset: 2048 ubiformat: formatting eraseblock 3759 -- 100 % complete ap_formatInternalFlash-ON100: UBI Format completed UBI: attached mtd6 to ubi0 UBI: MTD device name: "datafs" UBI: MTD device size: 470 MiB UBI: number of good PEBs: 3755 UBI: number of bad PEBs: 5 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 3714 UBI: total number of reserved PEBs: 41 UBI: number of PEBs reserved for bad PEB handling: 37 UBI: max/mean erase counter: 38/36 UBI: image sequence number: 1208912032 UBI: background thread "ubi_bgt0d" started, PID 1271 UBI device number 0, total 3755 LEBs (484485120 bytes, 462.0 MiB), available 3714 LEBs (479195136 bytes, 457.0 MiB), LEB size 129024 bytes (126.0 KiB) ap_formatInternalFlash-ON100: ubiattach was successful to ubi0 ap_formatInternalFlash-ON100: mknod was successful for /dev/ubi0 Set volume size to 479195136 Volume ID 0, size 3714 LEBs (479195136 bytes, 457.0 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "datafs", alignment 1 ap_formatInternalFlash-ON100: ubimkvol was successful for /dev/ubi0 UBIFS: default file-system created UBIFS: mounted UBI device 0, volume 0, name "datafs" UBIFS: file system size: 477388800 bytes (466200 KiB, 455 MiB, 3700 LEBs) UBIFS: journal size: 23869440 bytes (23310 KiB, 22 MiB, 185 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 4952683 bytes (4836 KiB) ap_failSafeUpdate: .... Format Completed ap_failSafeUpdate: Attempt #1 to retrieve http://failsafe.imageboot.com/failsafe/failsafe.html?model=ON100&mac=64:00:F1:20:FF:B6&serial=DNI15440BHM&pid=ON100-K9&vid=01 ap_failSafeUpdate: Bundle download was successful - in terms of a successful transfer ... ap_failSafeUpdate: Downloaded the bundle fine, but the tar file is corrupt ap_failSafeUpdate: Failed attempt 1 to download the recovery file!
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Feb 22 2011 - 14:06:09) Marvell version: 3.5.9 - Cisco Plasma U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D2340 Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:512 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled Module 0 is RGMII USB 0: host mode PEX 0: interface detected no Link. PEX 1: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0