Debian on Verbatim MediaShare Mini September 06, 2016 12:49AM |
Registered: 9 years ago Posts: 442 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6281A-BP LE The board type is Topkick0281 U-Boot 1.1.4 (Jul 13 2010 - 12:04:50) Marvell version: 3.4.27 USISH-SMB Ver: topkick0281-20100706-axentra U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0120 Soc: 88F6281 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv^M baudrate=115200 loads_echo=0 ipaddr=192.168.58.21 serverip=192.168.58.135 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 run_diag=yes CASset=min ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 bootargs=console=ttyS0,115200;version=topkick0281-002-001-20100701-verbatim initializeKernelRamdisk=run initializeUSB; nand erase clean 0x200000 0x600000; nand write.e 0x1200000 0x200000 0x300000; nand erase clean 0x800000 0x1000000; nand write.e 0x1800000 0x800000 0x800000 filesize=61123C ethaddr=00:27:13:ff:f1:f3 PK=VPRQ-FPTA-NWKT-QWWR console=console=ttyS0,115200 initializeDev=run initializeKernel; setenv bootargs console=ttyS0,115200 root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000 initializeKernel=run initializeUSB; nand erase clean 0x00200000 0x00600000; nand write.e 0x00800000 0x00200000 0x00600000 initializeUSB=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd save_crc=true install_mode=false bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console2=console=ttyS0,115200 bootcmd=nand read.e 0x800000 0x200000 0x600000; setenv bootargs $(console2) $(bootargs_root); bootm 0x800000 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no Environment size: 1920/131068 bytes Marvell>> help^M ? - alias for 'help' SatR - sample at reset sub-system, relevent for DB only base - print or set address offset boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol bubt - Burn an image on the Boot Nand Flash. chpart - change active partition cmp - memory compare cmpm - Compare Memory cp - memory copy cpumap - Display CPU memory mapping settings. crc32 - checksum calculation date - get/set/reset date & time dclk - Display the MV device CLKs. dhcp - invoke DHCP client to obtain IP/boot params diskboot- boot from IDE device echo - echo args to console eeprom - EEPROM sub-system erase - erase FLASH memory ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fi - Find value in the memory. flinfo - print FLASH memory information fsinfo - print information about filesystems fsload - load binary file from a filesystem image g - start application at cached address 'addr'(default addr 0x40000) go - start application at address 'addr' help - print online help icrc32 - checksum calculation ide - IDE sub-system iloop - infinite loop on address range imd - i2c memory display iminfo - print header information for application image imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing) imw - memory write (fill) inm - memory modify (constant address) iprobe - probe to discover valid I2C chip addresses ir - reading and changing MV internal register values. loop - infinite loop on address range ls - list files in a directory (default /) map - Diasplay address decode windows md - memory display me - PCI master enable mm - memory modify (auto-incrementing) mmcinit - init mmc card mp - map PCI BAR mtdparts- define flash/nand partitions mtest - simple RAM test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nbubt - Burn a boot loader image on the Boot Nand Flash. nm - memory modify (constant address) pci - list and access PCI Configuration Space phyRead - Read PCI-E Phy register pciePhyWrite - Write PCI-E Phy register phyRead - Read Phy register phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol rcvr - Satrt recovery process (Distress Beacon with TFTP server) reset - Perform RESET of the CPU resetenv - Return all environment variable to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage se - PCI Slave enable setenv - set environment variables sflash - read, write or erase the external SPI Flash. sg - scanning the PHYs status sp - Scan PCI bus. switchRegRead - Read switch register switchRegWrite - Write switch register tftpboot- boot image via network using TFTP protocol usb - USB sub-system usbboot - boot from USB device version - print monitor version Marvell>>
Re: Debian on Verbatim MediaShare Mini September 06, 2016 01:40AM |
Admin Registered: 13 years ago Posts: 18,580 |
ETH chip1: Marvell 88F6281 ETH chip2: Marvell 88E1116R LAN speed: 10/100/1000 LAN ports: 1
Re: Debian on Verbatim MediaShare Mini September 06, 2016 01:47AM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Debian on Verbatim MediaShare Mini September 06, 2016 01:58AM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Debian on Verbatim MediaShare Mini September 06, 2016 02:21AM |
Registered: 9 years ago Posts: 442 |
> ETH chip1: Marvell 88F6281 > ETH chip2: Marvell 88E1116R > LAN speed: 10/100/1000 > LAN ports: 1 >>
Re: Debian on Verbatim MediaShare Mini September 06, 2016 02:33AM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Debian on Verbatim MediaShare Mini September 06, 2016 02:35AM |
Registered: 9 years ago Posts: 442 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6281A-BP LE The board type is Topkick0281 U-Boot 1.1.4 (Jul 13 2010 - 12:04:50) Marvell version: 3.4.27 USISH-SMB Ver: topkick0281-20100706-axentra U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0120 Soc: 88F6281 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x200000, size 0x600000 ^MReading data from 0x200000 -- 0% complete.^MReading data from 0x20f000 -- 1% complete.^MReading data from 0x21e800 -- 2% complete.^MReading data from 0x22e000 -- 3% complete.^MReading data from 0x23d000 -- 4% complete.^M^MReading data from 0x24c800 -- 5% complete.^MReading data from 0x25c000 -- 6% complete.^MReading data from 0x26b800 -- 7% complete.^MReading data from 0x27a800 -- 8% complete.^MReading data from 0x28a000 -- 9% complete.^M^MReading data from 0x299800 -- 10% complete.^MReading data from 0x2a8800 -- 11% complete.^MReading data from 0x2b8000 -- 12% complete.^MReading data from 0x2c7800 -- 13% complete.^MReading data from 0x2d7000 -- 14% complete.^M^MReading data from 0x2e6000 -- 15% complete.^MReading data from 0x2f5800 -- 16% complete.^MReading data from 0x305000 -- 17% complete.^MReading data from 0x314000 -- 18% complete.^MReading data from 0x323800 -- 19% complete.^M^MReading data from 0x333000 -- 20% complete.^MReading data from 0x342800 -- 21% complete.^MReading data from 0x351800 -- 22% complete.^MReading data from 0x361000 -- 23% complete.^MReading data from 0x370800 -- 24% complete.^M^MReading data from 0x37f800 -- 25% complete.^MReading data from 0x38f000 -- 26% complete.^MReading data from 0x39e800 -- 27% complete.^MReading data from 0x3ae000 -- 28% complete.^MReading data from 0x3bd000 -- 29% complete.^M^MReading data from 0x3cc800 -- 30% complete.^MReading data from 0x3dc000 -- 31% complete.^MReading data from 0x3eb800 -- 32% complete.^MReading data from 0x3fa800 -- 33% complete.^MReading data from 0x40a000 -- 34% complete.^M^MReading data from 0x419800 -- 35% complete.^MReading data from 0x428800 -- 36% complete.^MReading data from 0x438000 -- 37% complete.^MReading data from 0x447800 -- 38% complete.^MReading data from 0x457000 -- 39% complete.^M^MReading data from 0x466000 -- 40% complete.^MReading data from 0x475800 -- 41% complete.^MReading data from 0x485000 -- 42% complete.^MReading data from 0x494000 -- 43% complete.^MReading data from 0x4a3800 -- 44% complete.^M^MReading data from 0x4b3000 -- 45% complete.^MReading data from 0x4c2800 -- 46% complete.^MReading data from 0x4d1800 -- 47% complete.^MReading data from 0x4e1000 -- 48% complete.^MReading data from 0x4f0800 -- 49% complete.^M^MReading data from 0x4ff800 -- 50% complete.^MReading data from 0x50f000 -- 51% complete.^MReading data from 0x51e800 -- 52% complete.^MReading data from 0x52e000 -- 53% complete.^MReading data from 0x53d000 -- 54% complete.^M^MReading data from 0x54c800 -- 55% complete.^MReading data from 0x55c000 -- 56% complete.^MReading data from 0x56b800 -- 57% complete.^MReading data from 0x57a800 -- 58% complete.^MReading data from 0x58a000 -- 59% complete.^M^MReading data from 0x599800 -- 60% complete.^MReading data from 0x5a8800 -- 61% complete.^MReading data from 0x5b8000 -- 62% complete.^MReading data from 0x5c7800 -- 63% complete.^MReading data from 0x5d7000 -- 64% complete.^M^MReading data from 0x5e6000 -- 65% complete.^MReading data from 0x5f5800 -- 66% complete.^MReading data from 0x605000 -- 67% complete.^MReading data from 0x614000 -- 68% complete.^MReading data from 0x623800 -- 69% complete.^M^MReading data from 0x633000 -- 70% complete.^MReading data from 0x642800 -- 71% complete.^MReading data from 0x651800 -- 72% complete.^MReading data from 0x661000 -- 73% complete.^MReading data from 0x670800 -- 74% complete.^M^MReading data from 0x67f800 -- 75% complete.^MReading data from 0x68f000 -- 76% complete.^MReading data from 0x69e800 -- 77% complete.^MReading data from 0x6ae000 -- 78% complete.^MReading data from 0x6bd000 -- 79% complete.^M^MReading data from 0x6cc800 -- 80% complete.^MReading data from 0x6dc000 -- 81% complete.^MReading data from 0x6eb800 -- 82% complete.^MReading data from 0x6fa800 -- 83% complete.^MReading data from 0x70a000 -- 84% complete.^M^MReading data from 0x719800 -- 85% complete.^MReading data from 0x728800 -- 86% complete.^MReading data from 0x738000 -- 87% complete.^MReading data from 0x747800 -- 88% complete.^MReading data from 0x757000 -- 89% complete.^M^MReading data from 0x766000 -- 90% complete.^MReading data from 0x775800 -- 91% complete.^MReading data from 0x785000 -- 92% complete.^MReading data from 0x794000 -- 93% complete.^MReading data from 0x7a3800 -- 94% complete.^M^MReading data from 0x7b3000 -- 95% complete.^MReading data from 0x7c2800 -- 96% complete.^MReading data from 0x7d1800 -- 97% complete.^MReading data from 0x7e1000 -- 98% complete.^MReading data from 0x7f0800 -- 99% complete.^M^MReading data from 0x7ff800 -- 100% complete. 6291456 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-07-16 14:28:07 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1657568 Bytes = 1.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux................................................................................................. ......... done, booting the kernel. ^MLinux version 2.6.22.18 (khaled@es5x86.axentra.com) (gcc version 4.3.2 (sdk3.2rc1-ct-ng-1.4.1) ) #1 Fri Jul 16 10: 28:00 EDT 2010 CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977 Machine: Feroceon-KW Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists. Total pages: 65024 Kernel command line: console=ttyS0,115200 ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc PID hash table entries: 1024 (order: 10, 4096 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB 0MB 0MB 0MB = 256MB total Memory: 256384KB available (3060K code, 221K data, 108K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 256MB SDRAM_CS1 ....base 10000000, size 256MB SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e8000000, size 128MB PEX0_IO ....base f2000000, size 1MB INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version kernel-2.6.22-topkick-1.0.0.2)-- USI-88F6281A Soc: 88F6281 A1 LE Detected Tclk 166666667 and SysClk 200000000 MV Buttons Device Load Marvell USB EHCI Host controller #0: c05c0600 PEX0 interface detected no Link. PCI: bus0: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: kw_clocksource clocksource has been installed. IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered RTC registered Use the XOR engines (acceleration) for enhancing the following functions: o RAID 5 Xor calculation o kernel memcpy o kenrel memzero Number of XOR engines to use: 4 cesadev_init(c0010ddc) mvCesaInit: sessions=640, queue=64, pSram=f0000000 MV Buttons Driver Load io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: module loaded Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o Single RX Queue support - ETH_DEF_RXQ=0 o Single TX Queue support - ETH_DEF_TXQ=0 o TCP segmentation offload enabled o Receive checksum offload enabled o Transmit checksum offload enabled o Network Fast Processing (Routing) supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Proc tool API enabled o Rx descripors: q0=128 o Tx descripors: q0=532 o Loading network interface(s): o eth0, ifindex = 1, GbE port = 0 Warning: Giga 1 is Powered Off mvFpRuleDb (cfd14000): 2048 entries, 8192 bytes Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Using static partition definition Creating 3 MTD partitions on "nand_mtd": 0x00000000-0x00200000 : "u-boot" 0x00200000-0x00800000 : "uImage" 0x00800000-0x10000000 : "root" UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd2 to ubi0 UBI: MTD device name: "root" UBI: MTD device size: 248 MiB UBI: number of good PEBs: 1984 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 1984 UBI: number of PEBs reserved for bad PEB handling: 38 UBI: max/mean erase counter: 1/0 UBI: background thread "ubi_bgt0d" started, PID 316 ehci_marvell ehci_marvell.70059: Marvell Orion EHCI ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected USB Universal Host Controller Interface driver v3.0 usb 1-1: new high speed USB device using ehci_marvell and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected usish: set gpio39 to 1 usb 1-1.4: new high speed USB device using ehci_marvell and address 3 usb 1-1.4: configuration #1 chosen from 1 choice usish: set gpio39 to 1 usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice pwrctl: dev_t_NO. = 0xdd00000, major = 221 pwrctl: HDD1(0),HDD2(0) TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: file system size: 239857664 bytes (234236 KiB, 228 MiB, 1889 LEBs) UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) UBIFS: media format: 4 (latest is 4) UBIFS: default compressor: zlib UBIFS: reserved for root: 0 bytes (0 KiB) VFS: Mounted root (ubifs filesystem). Freeing init memory: 108K Failed to execute /linuxrc. Attempting defaults... ^MINIT: version 2.86 booting^M Welcome to HipServ Press 'I' to enter interactive startup. Setting clock (utc): Tue Sep 6 03:27:33 EDT 2016 [ OK ]^M Starting udev: [ OK ]^M Setting hostname axentraserver.mediashareminirk.myverbatim.com: [ OK ]^M Checking filesystems Checking all file systems. [ OK ]^M Mounting local filesystems: mount: sysfs already mounted or /sys busy mount: according to mtab, /sys is already mounted on /sys [FAILED]^M Enabling /etc/fstab swaps: [ OK ] ^MINIT: Entering runlevel: 3^M Entering non-interactive startup HipServ startup:[ OK ]^M Starting reset: [ OK ]^M Bringing up loopback interface: [ OK ]^M Bringing up interface eth0: Determining IP information for eth0... done. /etc/init.d/iptables: line 42: /etc/sysconfig/networking/oe-profiles/default/ifcfg-eth0: No such file or directory Flushing all current rules and user defined chains: [ OK ]^M Clearing all current rules and user defined chains: [ OK ]^M [ OK ]^M[ OK ]^MApplying iptables firewall rules: [ OK ]^M [ OK ]^M Starting system logger: [ OK ]^M Starting kernel logger: [ OK ]^M Starting locator:[ OK ]^M Starting system message bus: [ OK ]^M Starting sshd: [ OK ]^M Starting cups: [ OK ]^M Starting xinetd: [ OK ]^M Starting vsftpd for vsftpd: [ OK ]^M Starting access-patrol:[ OK ]^M Starting httpd: [ OK ]^M Starting appserver: [ OK ]^M Starting crond: [ OK ]^M Starting SMB services: [ OK ]^M Starting NMB services: [ OK ]^M check_igd.pl: no process killed Starting igd-daemon:[ OK ]^M[ OK ]^M Starting OEone System Proxy: SPD starting....log level=1, uid=0 [ OK ]^M Starting Avahi daemon... [ OK ]^M Starting twonky: Starting /usr/local/TwonkyVision/twonkymedia ... Daemonizing... [ OK ]^M Starting DAAP server: [ OK ]^M Starting mynetworkd:[ OK ]^M HipServ - Checking if RAID needs to be rebuilt HipServ - No RAID found HipServ - Bringing up iptables HipServ - Updating date... [ OK ]^M success HipServ - Checking for updates... [ OK ]^M success HipServ - Enabling swap HipServ - Cleaning USB mountpoints HipServ - Mounting USB devices ufsd: module license 'Commercial product' taints kernel. ufsd: driver 8.1 (022_A) LBD=ON with ioctl loaded at bf04f000 NTFS read/write support included Hfs+/HfsX read/write support included Unknown HZ value! (88) Assume 100. Unknown HZ value! (88) Assume 100. Unknown HZ value! (88) Assume 100. Unknown HZ value! (88) Assume 100. HipServ - Checking for FTPS certificate HipServ - Found vsftpd key file HipServ - Starting usbreaderd: [ OK ] HipServ - boot complete axentraserver.mediashareminirk.myverbatim.com login:
Re: Debian on Verbatim MediaShare Mini September 06, 2016 02:49AM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Debian on Verbatim MediaShare Mini September 06, 2016 11:24PM |
Registered: 9 years ago Posts: 442 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6281A-BP LE The board type is Topkick0281 U-Boot 1.1.4 (Jul 13 2010 - 12:04:50) Marvell version: 3.4.27 USISH-SMB Ver: topkick0281-20100706-axentra U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0120 Soc: 88F6281 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10^M Marvell>> usb start^M (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Marvell>> ext2load usb 0:1 0x800000 /boot/uImage^M .... . ...... ............ ......................... ................................................... ...................................................................................................... ........................................................................................................ 3165294 bytes read Marvell>> ext2load usb 0:1 0x1100000 /boot/uInitrd^M .... . ...... ............ ......................... ................................................... ...................................................................................................... ................................................................................................................................................................................................................. .............................................................................................................................................................................................................................................................................................. 7179935 bytes read Marvell>> bootm 0x800000 0x1100000^M ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-09-07 3:59:49 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3165230 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Seagate FreeAgent Dockstar [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 243580K/262144K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 18564K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000016] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000529] Console: colour dummy device 80x30 [ 0.000582] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 0.090145] pid_max: default: 32768 minimum: 301 [ 0.090329] Security Framework initialized [ 0.090454] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090488] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091841] Initializing cgroup subsys io [ 0.091901] Initializing cgroup subsys devices [ 0.091942] Initializing cgroup subsys freezer [ 0.092001] Initializing cgroup subsys net_cls [ 0.092148] CPU: Testing write buffer coherency: ok [ 0.092941] Setting up static identity map for 0x8200 - 0x8258 [ 0.093424] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.099554] devtmpfs: initialized [ 0.107347] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.108151] prandom: seed boundary self test passed [ 0.113850] prandom: 100 self tests passed [ 0.113912] pinctrl core: initialized pinctrl subsystem [ 0.116298] NET: Registered protocol family 16 [ 0.117011] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.140186] cpuidle: using governor ladder [ 0.170181] cpuidle: using governor menu [ 0.170813] Feroceon L2: Enabling L2 [ 0.170882] Feroceon L2: Cache support initialised. [ 0.171465] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.178698] No ATAGs? [ 0.212447] vgaarb: loaded [ 0.213020] usbcore: registered new interface driver usbfs [ 0.213143] usbcore: registered new interface driver hub [ 0.213267] usbcore: registered new device driver usb [ 0.214945] clocksource: Switched to clocksource orion_clocksource [ 0.300536] NET: Registered protocol family 2 [ 0.301865] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.301928] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.301981] TCP: Hash tables configured (established 2048 bind 2048) [ 0.302089] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.302127] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.302450] NET: Registered protocol family 1 [ 0.303095] RPC: Registered named UNIX socket transport module. [ 0.303114] RPC: Registered udp transport module. [ 0.303125] RPC: Registered tcp transport module. [ 0.303136] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.303577] Unpacking initramfs... [ 1.255435] Freeing initrd memory: 7012K (c1100000 - c17d9000) [ 1.255624] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.257421] futex hash table entries: 256 (order: -1, 3072 bytes) [ 1.257536] audit: initializing netlink subsys (disabled) [ 1.257631] audit: type=2000 audit(1.250:1): initialized [ 1.258194] Initialise system trusted keyring [ 1.258853] zbud: loaded [ 1.259312] VFS: Disk quotas dquot_6.6.0 [ 1.259404] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.260265] NFS: Registering the id_resolver key type [ 1.260351] Key type id_resolver registered [ 1.260364] Key type id_legacy registered [ 1.260405] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.260426] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.260772] jffs2: version 2.2. (NAND) (SUMMARY) <C2><A9> 2001-2006 Red Hat, Inc. [ 1.261574] Key type big_key registered [ 1.292341] Key type asymmetric registered [ 1.292377] Asymmetric key parser 'x509' registered [ 1.292537] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.292568] io scheduler noop registered [ 1.292592] io scheduler deadline registered [ 1.292693] io scheduler cfq registered (default) [ 1.294756] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 1.296193] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated [ 1.296846] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated [ 1.297662] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.336046] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.336440] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.376018] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.376854] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.379070] console [ttyS0] disabled [ 1.379175] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 1.969260] console [ttyS0] enabled [ 1.974874] nand: Could not find valid ONFI parameter page; aborting [ 1.981304] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 1.987657] nand: Hynix NAND 256MiB 3,3V 8-bit [ 1.992085] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.999667] Scanning device for bad blocks [ 2.144862] libphy: Fixed MDIO Bus: probed [ 2.149651] libphy: orion_mdio_bus: probed [ 2.154184] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.161889] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.168603] ehci-pci: EHCI PCI platform driver [ 2.173141] ehci-orion: EHCI orion driver [ 2.177459] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.182964] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.190926] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.214990] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.221347] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.228156] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.235380] usb usb1: Product: EHCI Host Controller [ 2.240244] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 2.246860] usb usb1: SerialNumber: f1050000.ehci [ 2.252680] hub 1-0:1.0: USB hub found [ 2.256548] hub 1-0:1.0: 1 port detected [ 2.261915] mousedev: PS/2 mouse device common for all mice [ 2.268566] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 2.275760] i2c /dev entries driver [ 2.281130] hidraw: raw HID events driver (C) Jiri Kosina [ 2.287212] drop_monitor: Initializing network drop monitor service [ 2.293854] NET: Registered protocol family 17 [ 2.298740] Key type dns_resolver registered [ 2.304245] registered taskstats version 1 [ 2.308450] Loading compiled-in X.509 certificates [ 2.313323] zswap: loaded using pool lzo/zbud [ 2.331302] Key type encrypted registered [ 2.336667] rtc-mv f1010300.rtc: setting system clock to 2013-01-01 04:14:56 UTC (1357013696) [ 2.349081] Freeing unused kernel memory: 296K (c07d8000 - c0822000) Loading, please wait... [ 2.463843] systemd-udevd[79]: starting version 215 [ 2.478252] random: systemd-udevd urandom read with 3 bits of entropy available [ 2.575149] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 2.735715] usb 1-1: New USB device found, idVendor=058f, idProduct=6254 [ 2.742443] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.765235] hub 1-1:1.0: USB hub found [ 2.773282] hub 1-1:1.0: 4 ports detected [ 3.054991] usb 1-1.4: new high-speed USB device number 3 using orion-ehci [ 3.186811] usb 1-1.4: New USB device found, idVendor=154b, idProduct=009f [ 3.193688] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.201021] usb 1-1.4: Product: USB 2.0 FD [ 3.205130] usb 1-1.4: Manufacturer: PNY Technologies [ 3.210163] usb 1-1.4: SerialNumber: 0400000000015713 [ 3.240933] SCSI subsystem initialized [ 3.252249] usb-storage 1-1.4:1.0: USB Mass Storage device detected [ 3.259328] scsi host0: usb-storage 1-1.4:1.0 [ 3.266808] usbcore: registered new interface driver usb-storage [ 3.277720] usbcore: registered new interface driver uas [ 4.532606] scsi 0:0:0:0: Direct-Access PNY USB 2.0 FD 1100 PQ: 0 ANSI: 4 [ 4.554163] sd 0:0:0:0: [sda] 15826944 512-byte logical blocks: (8.10 GB/7.54 GiB) [ 4.564384] sd 0:0:0:0: [sda] Write Protect is off [ 4.570109] sd 0:0:0:0: [sda] No Caching mode page found [ 4.575487] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 4.588946] sda: sda1 [ 4.595989] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 4.608362] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Checking root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 18.151189] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.171744] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [ESC[36minfoESC[39;49m] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 19.949053] systemd-udevd[282]: starting version 215 ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Synthesizing the initial hotplug events...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [....] Waiting for /dev to be fully populated...[ 20.621720] orion_wdt: Initial timeout 25 sec [ 20.658836] marvell-cesa: probe of f1030000.crypto failed with error -524 [ 20.721949] random: nonblocking pool is initialized ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [....] Activating swap...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [ 22.670267] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 14518/494832 files, 167035/1978315 blocks ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [ 24.487097] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [....] Activating lvm and md swap...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [....] Checking file systems...fsck from util-linux 2.25.2 ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [....] Loading kernel modules...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [....] Cleaning up temporary files... /tmpESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Mounting local filesystems...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [....] Activating swapfile swap...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [....] Cleaning up temporary files...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Setting kernel variables ...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [ 28.245861] NET: Registered protocol family 10 [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Cannot find device "eth0" Bind socket to interface: No such device If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging.. exiting. Failed to bring up eth0. ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone. [....] Starting rpcbind daemon...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Starting NFS common utilities: statd idmapdESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Cleaning up temporary files...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. ^MINIT: Entering runlevel: 2^M [ESC[36minfoESC[39;49m] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1165 (syslogd) ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Starting system message bus: dbusESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Starting NFS common utilities: statd idmapdESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemonESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Not starting NFS kernel daemon: no exports. ...ESC[?25lESC[?1cESC7ESC[1G[ESC[33mwarnESC[39;49mESC8ESC[?25hESC[?0c ESC[33m(warning).ESC[39;49m [....] Starting NTP server: ntpdESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1163 (klogd) ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. [....] Starting OpenBSD Secure Shell server: sshdESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c. ^M Debian GNU/Linux 8 debian ttyS0 debian login: root^M Password: Last login: Mon Dec 31 20:08:40 PST 2012 on ttyS0 Linux debian 4.4.0-kirkwood-tld-1 #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@debian:~#
Re: Debian on Verbatim MediaShare Mini September 07, 2016 12:04AM |
Admin Registered: 13 years ago Posts: 18,580 |