|
how to set MTDs writeable? December 01, 2016 03:08PM |
Registered: 9 years ago Posts: 42 |
root@publik:~# fw_setenv ipaddr 10.9.1.208 Can't open /dev/mtd0: Permission denied Error: can't write fw_env to flash root@publik:~#
|
Re: how to set MTDs writeable? December 01, 2016 03:36PM |
Admin Registered: 13 years ago Posts: 18,997 |
> root@publik:~# fw_setenv ipaddr 10.9.1.208 > Can't open /dev/mtd0: Permission denied > Error: can't write fw_env to flash > root@publik:~# >>
uname -a cat /proc/cmdline cat /proc/mtd dmesg | grep -i mtd dmesg | grep -i 0x000 fw_printenv
|
Re: how to set MTDs writeable? December 01, 2016 03:42PM |
Registered: 9 years ago Posts: 42 |
root@publik:~# uname -a Linux publik 4.8.3-kirkwood-tld-1 #1 PREEMPT Thu Oct 20 23:33:18 PDT 2016 armv5tel GNU/Linux root@publik:~# cat /proc/cmdline console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:1M(u-boot),512K(uboot_env),512K(key_store),512K(info),10M(etc),10M(kernel_1),48896K(rootfs1),10M(kernel_2),-(rootfs2) root@publik:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 00080000 00020000 "uboot_env" mtd2: 00080000 00020000 "key_store" mtd3: 00080000 00020000 "info" mtd4: 00a00000 00020000 "etc" mtd5: 00a00000 00020000 "kernel_1" mtd6: 02fc0000 00020000 "rootfs1" mtd7: 00a00000 00020000 "kernel_2" mtd8: 02fc0000 00020000 "rootfs2" root@publik:~# dmesg | grep -i mtd [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:1M(u-boot),512K(uboot_env),512K(key_store),512K(info),10M(etc),10M(kernel_1),48896K(rootfs1),10M(kernel_2),-(rootfs2) [ 5.919157] 9 ofpart partitions found on MTD device orion_nand [ 5.925042] Creating 9 MTD partitions on "orion_nand": root@publik:~# dmesg | grep -i 0x000 [ 5.893386] Bad eraseblock 852 at 0x000006a80000 [ 5.905878] Bad eraseblock 934 at 0x0000074c0000 [ 5.930205] 0x000000000000-0x000000100000 : "uboot" [ 5.936602] 0x000000100000-0x000000180000 : "uboot_env" [ 5.943207] 0x000000180000-0x000000200000 : "key_store" [ 5.949869] 0x000000200000-0x000000280000 : "info" [ 5.956180] 0x000000280000-0x000000c80000 : "etc" [ 5.962344] 0x000000c80000-0x000001680000 : "kernel_1" [ 5.968911] 0x000001680000-0x000004640000 : "rootfs1" [ 5.975647] 0x000004640000-0x000005040000 : "kernel_2" [ 5.982220] 0x000005040000-0x000008000000 : "rootfs2" root@publik:~# fw_printenv bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec device=0:1 disks=0 1 2 3 ethact=egiga0 if_netconsole=ping $serverip led_error=orange blinking led_exit=green off led_init=green blinking load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15 arcNumber=3956 mtdparts=mtdparts=mtdparts=orion_nand:1M(u-boot),512K(uboot_env),512K(key_store),512K(info),10M(etc),10M(kernel_1),48896K(rootfs1),10M(kernel_2),-(rootfs2) ethaddr=b0:b2:dc:ee:d4:f2 ipaddr=10.9.1.209 serverip=10.9.1.200 bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi; sleep 3 dtb_file=/boot/dts/kirkwood-nsa320.dtb devices=ide bootdelay=5 bootdev=ide stderr=nc stdin=nc stdout=nc usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi load_uimage=ext2load ide 0:1 0x800000 /boot/uImage load_initrd=ext2load ide 0:1 0x1100000 /boot/uInitrd load_dtb=ext2load ide 0:1 0x1c00000 /boot/dts/kirkwood-nsa320.dtb root@publik:~#
|
Re: how to set MTDs writeable? December 01, 2016 03:47PM |
Admin Registered: 13 years ago Posts: 18,997 |
cat /etc/fw_env.config
ls -l /dev/mtd*
|
Re: how to set MTDs writeable? December 01, 2016 10:33PM |
Registered: 9 years ago Posts: 42 |
root@publik:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 root@publik:~# ls -l /dev/mtd* crw------- 1 root root 90, 0 Dec 1 21:36 /dev/mtd0 crw------- 1 root root 90, 1 Dec 1 21:36 /dev/mtd0ro crw------- 1 root root 90, 2 Dec 1 21:36 /dev/mtd1 crw------- 1 root root 90, 3 Dec 1 21:36 /dev/mtd1ro crw------- 1 root root 90, 4 Dec 1 21:36 /dev/mtd2 crw------- 1 root root 90, 5 Dec 1 21:36 /dev/mtd2ro crw------- 1 root root 90, 6 Dec 1 21:36 /dev/mtd3 crw------- 1 root root 90, 7 Dec 1 21:36 /dev/mtd3ro crw------- 1 root root 90, 8 Dec 1 21:36 /dev/mtd4 crw------- 1 root root 90, 9 Dec 1 21:36 /dev/mtd4ro crw------- 1 root root 90, 10 Dec 1 21:36 /dev/mtd5 crw------- 1 root root 90, 11 Dec 1 21:36 /dev/mtd5ro crw------- 1 root root 90, 12 Dec 1 21:36 /dev/mtd6 crw------- 1 root root 90, 13 Dec 1 21:36 /dev/mtd6ro crw------- 1 root root 90, 14 Dec 1 21:36 /dev/mtd7 crw------- 1 root root 90, 15 Dec 1 21:36 /dev/mtd7ro crw------- 1 root root 90, 16 Dec 1 21:36 /dev/mtd8 crw------- 1 root root 90, 17 Dec 1 21:36 /dev/mtd8ro brw-rw---- 1 root disk 31, 0 Dec 1 21:36 /dev/mtdblock0 brw-rw---- 1 root disk 31, 1 Dec 1 21:36 /dev/mtdblock1 brw-rw---- 1 root disk 31, 2 Dec 1 21:36 /dev/mtdblock2 brw-rw---- 1 root disk 31, 3 Dec 1 21:36 /dev/mtdblock3 brw-rw---- 1 root disk 31, 4 Dec 1 21:36 /dev/mtdblock4 brw-rw---- 1 root disk 31, 5 Dec 1 21:36 /dev/mtdblock5 brw-rw---- 1 root disk 31, 6 Dec 1 21:36 /dev/mtdblock6 brw-rw---- 1 root disk 31, 7 Dec 1 21:36 /dev/mtdblock7 brw-rw---- 1 root disk 31, 8 Dec 1 21:36 /dev/mtdblock8 root@publik:~#
|
Re: how to set MTDs writeable? December 01, 2016 10:39PM |
Admin Registered: 13 years ago Posts: 18,997 |
|
Re: how to set MTDs writeable? December 01, 2016 11:54PM |
Registered: 9 years ago Posts: 42 |
nc -lu 666610.9.1.222 nc Test client cmd line:
nc -u 10.9.1.200 6666to ensure this is no Firewall etc. issue. Text i type in either Computers window appears in the other window, but only after i press <Enter>.
|
Re: how to set MTDs writeable? December 20, 2016 07:14PM |
Registered: 7 years ago Posts: 3 |
root@pogo:~# fw_setenv ipaddr '192.168.1.2' Can't open /dev/mtd0: Permission denied Error: can't write fw_env to flash
root@pogo:~# uname -a Linux pogo 4.8.3-kirkwood-tld-1 #1 PREEMPT Thu Oct 20 23:33:18 PDT 2016 armv5tel GNU/Linux root@pogo:~# cat /proc/cmdline console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) root@pogo:~# cat /proc/mtd dev: size erasesize name mtd0: 00200000 00020000 "u-boot" mtd1: 00300000 00020000 "uImage" mtd2: 00300000 00020000 "uImage2" mtd3: 00800000 00020000 "failsafe" mtd4: 07000000 00020000 "root" root@pogo:~# dmesg | grep -i mtd [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) [ 6.948613] 5 ofpart partitions found on MTD device orion_nand [ 6.954440] Creating 5 MTD partitions on "orion_nand": root@pogo:~# dmesg | grep -i 0x000 [ 5.980792] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit] [ 5.980814] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 5.980835] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit] [ 6.942228] Bad eraseblock 1003 at 0x000007d60000 [ 6.959566] 0x000000000000-0x000000200000 : "u-boot" [ 6.966226] 0x000000200000-0x000000500000 : "uImage" [ 6.972777] 0x000000500000-0x000000800000 : "uImage2" [ 6.979475] 0x000000800000-0x000001000000 : "failsafe" [ 6.986284] 0x000001000000-0x000008000000 : "root" [ 8.243380] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010 root@pogo:~# fw_printenv bootcmd_exec=mw 0x800000 0 1; run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 0x1100000; fi; else if run load_dtb; then bootm 0x800000 - 0x1c00000; else bootm 0x800000; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 device=0:1 disks=0 1 2 3 ethact=egiga0 if_netconsole=ping $serverip led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device 0x1c00000 $dtb_file load_initrd=echo loading uInitrd ...; ext2load $bootdev $device 0x1100000 /boot/uInitrd load_uimage=echo loading uImage ...; ext2load $bootdev $device 0x800000 /boot/uImage mainlineLinux=yes mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 0x800000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_import=echo importing envs ...; env import -t 0x810000 uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15 arcNumber=3960 machid=f78 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethaddr=00:25:31:04:d8:e9 ipaddr=192.168.1.22 serverip=192.168.1.3 devices=mmc usb ide bootdev=mmc root@pogo:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 root@pogo:~# ls -l /dev/mtd* crw------- 1 root root 90, 0 Dec 31 1969 /dev/mtd0 crw------- 1 root root 90, 1 Dec 31 1969 /dev/mtd0ro crw------- 1 root root 90, 2 Dec 31 1969 /dev/mtd1 crw------- 1 root root 90, 3 Dec 31 1969 /dev/mtd1ro crw------- 1 root root 90, 4 Dec 31 1969 /dev/mtd2 crw------- 1 root root 90, 5 Dec 31 1969 /dev/mtd2ro crw------- 1 root root 90, 6 Dec 31 1969 /dev/mtd3 crw------- 1 root root 90, 7 Dec 31 1969 /dev/mtd3ro crw------- 1 root root 90, 8 Dec 31 1969 /dev/mtd4 crw------- 1 root root 90, 9 Dec 31 1969 /dev/mtd4ro brw-rw---- 1 root disk 31, 0 Dec 31 1969 /dev/mtdblock0 brw-rw---- 1 root disk 31, 1 Dec 31 1969 /dev/mtdblock1 brw-rw---- 1 root disk 31, 2 Dec 31 1969 /dev/mtdblock2 brw-rw---- 1 root disk 31, 3 Dec 31 1969 /dev/mtdblock3 brw-rw---- 1 root disk 31, 4 Dec 31 1969 /dev/mtdblock4
mtdparts=mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
|
Re: how to set MTDs writeable? December 21, 2016 05:07PM |
Admin Registered: 13 years ago Posts: 18,997 |
Quote
root@pogo:~# cat /proc/cmdline
console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
mtd partitions were not detected at all, i had to add to /boot/uEnv.txt
mtdparts=mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
|
Re: how to set MTDs writeable? December 22, 2016 03:21PM |
Registered: 7 years ago Posts: 3 |
root@pogo:/boot# mv uEnv.txt Disabled_uEnv.txt root@pogo:/boot# cd root@pogo:~# shutdown -r now
root@pogo:~# uptime
15:15:00 up 1 min, 1 user, load average: 0.96, 0.36, 0.13
root@pogo:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.8.3-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Thu Oct 20 23:33:18 PDT 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt:Machine model: Pogoplug v4
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat c08b1e78, node_mem_map c7ef9000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 113384K/131072K available (6149K kernel code, 614K rwdata, 1664K rodata, 308K init, 318K bss, 17688K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0609718 (6150 kB)
.init : 0xc07dd000 - 0xc082a000 ( 308 kB)
.data : 0xc082a000 - 0xc08c391c ( 615 kB)
.bss : 0xc08c391c - 0xc0913170 ( 319 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.000648] Console: colour dummy device 80x30
[ 0.000689] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
[ 0.090115] pid_max: default: 32768 minimum: 301
[ 0.090369] Security Framework initialized
[ 0.090558] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090586] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091946] CPU: Testing write buffer coherency: ok
[ 0.092478] Setting up static identity map for 0x8200 - 0x8258
[ 0.092796] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.097763] devtmpfs: initialized
[ 0.104338] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.104666] prandom: seed boundary self test passed
[ 0.109155] prandom: 100 self tests passed
[ 0.109171] pinctrl core: initialized pinctrl subsystem
[ 0.110847] NET: Registered protocol family 16
[ 0.111465] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.140136] cpuidle: using governor ladder
[ 0.170132] cpuidle: using governor menu
[ 0.170680] Feroceon L2: Enabling L2
[ 0.170734] Feroceon L2: Cache support initialised.
[ 0.171244] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.177178] No ATAGs?
[ 0.211843] vgaarb: loaded
[ 0.212262] usbcore: registered new interface driver usbfs
[ 0.212379] usbcore: registered new interface driver hub
[ 0.212455] usbcore: registered new device driver usb
[ 0.213802] clocksource: Switched to clocksource orion_clocksource
[ 0.268773] VFS: Disk quotas dquot_6.6.0
[ 0.268871] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.282531] NET: Registered protocol family 2
[ 0.283549] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.283583] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.283608] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.283688] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.283714] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.283987] NET: Registered protocol family 1
[ 0.284599] RPC: Registered named UNIX socket transport module.
[ 0.284614] RPC: Registered udp transport module.
[ 0.284623] RPC: Registered tcp transport module.
[ 0.284632] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.284647] PCI: CLS 0 bytes, default 32
[ 0.284929] Unpacking initramfs...
[ 1.061335] Freeing initrd memory: 7176K (c7411000 - c7b13000)
[ 1.061535] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.062744] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 1.062801] audit: initializing netlink subsys (disabled)
[ 1.062862] audit: type=2000 audit(1.050:1): initialized
[ 1.063241] Initialise system trusted keyrings
[ 1.063479] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 1.063588] zbud: loaded
[ 1.064773] NFS: Registering the id_resolver key type
[ 1.064808] Key type id_resolver registered
[ 1.064818] Key type id_legacy registered
[ 1.064838] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.064850] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.065168] jffs2: version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.
[ 1.065497] orangefs_init: called with debug mask: :none: :0:
[ 1.065950] orangefs: module version upstream loaded
[ 1.066257] Key type big_key registered
[ 2.553810] random: fast init done
[ 5.975117] Key type asymmetric registered
[ 5.975137] Asymmetric key parser 'x509' registered
[ 5.975238] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 5.975253] io scheduler noop registered
[ 5.975263] io scheduler deadline registered
[ 5.975302] io scheduler cfq registered (default)
[ 5.976320] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[ 5.976340] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[ 5.976736] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 5.977787] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
[ 5.978602] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated
[ 5.979575] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00
[ 5.979599] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 5.979616] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 5.979632] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 5.979646] pci_bus 0000:00: scanning bus
[ 5.979683] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 5.979740] pci 0000:00:01.0: calling pci_fixup_ide_bases+0x0/0x40
[ 5.980074] pci_bus 0000:00: fixups for bus
[ 5.980087] PCI: bus0: Fast back to back transfers disabled
[ 5.980106] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 0
[ 5.980116] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 5.980137] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 1
[ 5.980387] pci_bus 0000:01: scanning bus
[ 5.980432] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[ 5.980468] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[ 5.980491] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[ 5.980512] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit]
[ 5.980551] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x40
[ 5.980625] pci 0000:01:00.0: supports D1
[ 5.980635] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 5.980647] pci 0000:01:00.0: PME# disabled
[ 6.003868] pci_bus 0000:01: fixups for bus
[ 6.003883] PCI: bus1: Fast back to back transfers disabled
[ 6.003899] pci_bus 0000:01: bus scan returning with max=01
[ 6.003913] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 6.003926] pci_bus 0000:00: bus scan returning with max=01
[ 6.003942] pci 0000:00:01.0: fixup irq: got 0
[ 6.003951] pci 0000:00:01.0: assigning IRQ 00
[ 6.004014] pci 0000:01:00.0: fixup irq: got 84
[ 6.004024] pci 0000:01:00.0: assigning IRQ 84
[ 6.004063] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[ 6.004088] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 6.004117] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[ 6.004144] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[ 6.004167] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 6.004186] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 6.004285] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[ 6.004315] pcieport 0000:00:01.0: enabling bus mastering
[ 6.004368] pci 0000:01:00.0: calling quirk_usb_early_handoff+0x0/0x634
[ 6.004382] pci 0000:00:01.0: enabling bus mastering
[ 6.004395] pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 6.004746] mv_xor f1060800.xor: Marvell shared XOR driver
[ 6.064678] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 6.064952] mv_xor f1060900.xor: Marvell shared XOR driver
[ 6.124672] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 6.125275] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 6.126925] console [ttyS0] disabled
[ 6.126999] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[ 6.824710] console [ttyS0] enabled
[ 6.829832] nand: Could not find valid ONFI parameter page; aborting
[ 6.836229] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 6.842552] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 6.847000] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 6.854568] Scanning device for bad blocks
[ 6.940731] Bad eraseblock 1003 at 0x000007d60000
[ 6.947105] 5 ofpart partitions found on MTD device orion_nand
[ 6.952911] Creating 5 MTD partitions on "orion_nand":
[ 6.958055] 0x000000000000-0x000000200000 : "u-boot"
[ 6.964733] 0x000000200000-0x000000500000 : "uImage"
[ 6.971288] 0x000000500000-0x000000800000 : "uImage2"
[ 6.977968] 0x000000800000-0x000001000000 : "failsafe"
[ 6.984754] 0x000001000000-0x000008000000 : "root"
[ 6.993732] libphy: Fixed MDIO Bus: probed
[ 6.998047] libphy: mdio_driver_register: mv88e6085
[ 7.003314] libphy: orion_mdio_bus: probed
[ 7.013445] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 8.113402] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:d8:e9
[ 8.122268] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.128814] ehci-pci: EHCI PCI platform driver
[ 8.133311] ehci-orion: EHCI orion driver
[ 8.137527] orion-ehci f1050000.ehci: EHCI Host Controller
[ 8.143026] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 8.150897] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 8.183842] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 8.190076] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.196871] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.204085] usb usb1: Product: EHCI Host Controller
[ 8.208946] usb usb1: Manufacturer: Linux 4.8.3-kirkwood-tld-1 ehci_hcd
[ 8.215548] usb usb1: SerialNumber: f1050000.ehci
[ 8.221096] hub 1-0:1.0: USB hub found
[ 8.224946] hub 1-0:1.0: 1 port detected
[ 8.229572] xhci_hcd 0000:01:00.0: enabling bus mastering
[ 8.229587] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 8.234892] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 8.243432] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010
[ 8.251897] xhci_hcd 0000:01:00.0: enabling Mem-Wr-Inval
[ 8.252147] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.258941] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.266154] usb usb2: Product: xHCI Host Controller
[ 8.271015] usb usb2: Manufacturer: Linux 4.8.3-kirkwood-tld-1 xhci-hcd
[ 8.277618] usb usb2: SerialNumber: 0000:01:00.0
[ 8.283086] hub 2-0:1.0: USB hub found
[ 8.286930] hub 2-0:1.0: 2 ports detected
[ 8.291575] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 8.296857] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[ 8.304387] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 8.312595] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[ 8.319384] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.326599] usb usb3: Product: xHCI Host Controller
[ 8.331460] usb usb3: Manufacturer: Linux 4.8.3-kirkwood-tld-1 xhci-hcd
[ 8.338770] usb usb3: SerialNumber: 0000:01:00.0
[ 8.344251] hub 3-0:1.0: USB hub found
[ 8.348023] hub 3-0:1.0: 2 ports detected
[ 8.353215] mousedev: PS/2 mouse device common for all mice
[ 8.643840] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[ 8.815704] usb 2-1: New USB device found, idVendor=0bc2, idProduct=3322
[ 8.822379] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 8.829515] usb 2-1: Product: Expansion Desk
[ 8.833772] usb 2-1: Manufacturer: Seagate
[ 8.837872] usb 2-1: SerialNumber: NA8ERWZQ
[ 8.953903] usb 3-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 8.984629] usb 3-2: New USB device found, idVendor=0bc2, idProduct=a0a4
[ 8.991308] usb 3-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 8.998443] usb 3-2: Product: Backup+ Desk
[ 9.002520] usb 3-2: Manufacturer: Seagate
[ 9.006622] usb 3-2: SerialNumber: NA5KY6LH
[ 9.443833] rtc-mv f1010300.rtc: internal RTC not ticking
[ 9.449425] i2c /dev entries driver
[ 9.454335] hidraw: raw HID events driver (C) Jiri Kosina
[ 9.460259] drop_monitor: Initializing network drop monitor service
[ 9.466826] NET: Registered protocol family 17
[ 9.471491] Key type dns_resolver registered
[ 9.476804] registered taskstats version 1
[ 9.480890] Loading compiled-in X.509 certificates
[ 9.485745] zswap: loaded using pool lzo/zbud
[ 9.512093] Key type encrypted registered
[ 9.516845] hctosys: unable to open rtc device (rtc0)
[ 9.523251] PM: Hibernation image not present or could not be loaded.
[ 9.524794] Freeing unused kernel memory: 308K (c07dd000 - c082a000)
[ 9.531121] This architecture does not have kernel memory protection.
[ 9.620835] systemd-udevd[94]: starting version 215
[ 9.819865] SCSI subsystem initialized
[ 9.828523] usb 3-2: USB controller 0000:01:00.0 does not support streams, which are required by the UAS driver.
[ 9.899635] usb 3-2: Please try an other USB controller if you wish to use UAS.
[ 9.908613] mvsdio f1090000.mvsdio: Got CD GPIO
[ 9.917622] libata version 3.00 loaded.
[ 9.938523] usb-storage 3-2:1.0: USB Mass Storage device detected
[ 9.967717] sata_mv f1080000.sata: version 1.28
[ 9.971629] sata_mv f1080000.sata: slots 32 ports 1
[ 9.979702] scsi host0: sata_mv
[ 9.980209] ata1: SATA max UDMA/133 irq 32
[ 10.010288] mmc0: host does not support reading read-only switch, assuming write-enable
[ 10.014760] mmc0: new high speed SDHC card at address 1234
[ 10.107392] usb-storage 3-2:1.0: Quirks match for vid 0bc2 pid a0a4: 2000000
[ 10.124083] scsi host1: usb-storage 3-2:1.0
[ 10.130556] usbcore: registered new interface driver usb-storage
[ 10.136754] mmcblk0: mmc0:1234 SA16G 14.4 GiB
[ 10.143545] mmcblk0: p1
[ 10.159060] scsi host2: uas
[ 10.165687] usbcore: registered new interface driver uas
[ 10.172335] scsi 2:0:0:0: Direct-Access Seagate Expansion Desk 9401 PQ: 0 ANSI: 6
[ 10.306092] ata1: SATA link down (SStatus 0 SControl F300)
[ 10.338936] sd 2:0:0:0: [sda] 5860533167 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 10.347894] sd 2:0:0:0: [sda] 4096-byte physical blocks
[ 10.354303] sd 2:0:0:0: [sda] Write Protect is off
[ 10.359085] sd 2:0:0:0: [sda] Mode Sense: 4f 00 00 00
[ 10.359618] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.593167] sda: sda1 sda2
[ 10.600757] sd 2:0:0:0: [sda] Attached SCSI disk
[ 10.610244] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 11.204659] scsi 1:0:0:0: Direct-Access Seagate Backup+ Desk 050B PQ: 0 ANSI: 6
[ 11.215928] sd 1:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.73 TiB)
[ 11.225976] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 11.237321] sd 1:0:0:0: [sdb] Write Protect is off
[ 11.242110] sd 1:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[ 11.245575] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.478620] sdb: sdb1 sdb2 sdb3
[ 11.489419] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 20.892756] PM: Starting manual resume from disk
[ 20.898053] PM: Hibernation image partition 8:17 present
[ 20.898059] PM: Looking for hibernation image.
[ 20.917798] PM: Image not found (code -22)
[ 20.917809] PM: Hibernation image not present or could not be loaded.
[ 21.173377] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem
[ 21.224504] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 22.980451] systemd-udevd[314]: starting version 215
[ 23.330612] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 23.734537] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 23.770438] orion_wdt: Initial timeout 25 sec
[ 24.901018] Adding 204796k swap on /dev/sdb1. Priority:1 extents:1 across:204796k FS
[ 24.988552] Adding 196600k swap on /dev/sda1. Priority:1 extents:1 across:196600k FS
[ 25.130911] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[ 25.430881] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro
[ 26.587547] random: crng init done
[ 27.976121] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[ 28.235768] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null)
[ 28.667064] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 32.950245] NET: Registered protocol family 10
[ 32.955919] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 33.976432] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 33.986284] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 41.978017] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 41.995822] NFSD: starting 90-second grace period (net c08a83d0)
[ 61.484381] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[ 65.334125] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
root@pogo:~# cat /proc/cmdline
console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
root@pogo:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00200000 00020000 "u-boot"
mtd1: 00300000 00020000 "uImage"
mtd2: 00300000 00020000 "uImage2"
mtd3: 00800000 00020000 "failsafe"
mtd4: 07000000 00020000 "root"
root@pogo:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd0 0xc0000 0x20000 0x20000
root@pogo:~# fw_printenv
bootcmd_exec=mw 0x800000 0 1; run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 0x1100000; fi; else if run load_dtb; then bootm 0x800000 - 0x1c00000; else bootm 0x800000; fi; fi
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
device=0:1
disks=0 1 2 3
ethact=egiga0
if_netconsole=ping $serverip
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device 0x1c00000 $dtb_file
load_initrd=echo loading uInitrd ...; ext2load $bootdev $device 0x1100000 /boot/uInitrd
load_uimage=echo loading uImage ...; ext2load $bootdev $device 0x800000 /boot/uImage
mainlineLinux=yes
mtdids=nand0=orion_nand
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 0x800000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x810000
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
usb_ready_retry=15
arcNumber=3960
machid=f78
mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb
ethaddr=00:25:31:04:d8:e9
ipaddr=192.168.1.22
serverip=192.168.1.3
devices=mmc usb ide
bootdev=mmc
root@pogo:~# fw_setenv ipaddr '192.168.1.2' Can't open /dev/mtd0: Permission denied Error: can't write fw_env to flash root@pogo:~# ls -la /dev/mtd0 crw------- 1 root root 90, 0 Dec 31 1969 /dev/mtd0
|
Re: how to set MTDs writeable? December 22, 2016 04:38PM |
Admin Registered: 13 years ago Posts: 18,997 |
cd /boot touch uEnv.txt echo "mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)" > uEnv.txtVerify:
cat uEnv.txt expected output: mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
|
Re: how to set MTDs writeable? December 23, 2016 10:00AM |
Registered: 7 years ago Posts: 3 |
fw_setenv mtdparts 'mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)'And now everything works with a empty uEnv.txt
|
Re: how to set MTDs writeable? September 23, 2017 06:11AM |
Registered: 9 years ago Posts: 42 |
cat /proc/cmdline cd /boot touch uEnv.txt echo "mtdparts=mtdparts=orion_nand:1M(u-boot),512K(uboot_env),512K(key_store),512K(info),10M(etc),10M(kernel_1),48896K(rootfs1),10M(kernel_2),-(rootfs2)" >uEnv.txt cat uEnv.txt mtdparts=mtdparts=orion_nand:1M(u-boot),512K(uboot_env),512K(key_store),512K(info),10M(etc),10M(kernel_1),48896K(rootfs1),10M(kernel_2),-(rootfs2)
|
Re: how to set MTDs writeable? December 31, 2021 03:22AM |
Registered: 13 years ago Posts: 26 |
# fw_setenv test test Can't open /dev/mtd0: Permission denied Error: can't write fw_env to flash
# uname -a Linux dockstar-multimedia 5.10.0-8-marvell #1 Debian 5.10.46-3 (2021-07-28) armv5tel GNU/Linux # cat /proc/cmdline console=ttyS0,115200 root=/dev/nfs rw rootfstype=nfs rootwait nfsroot=192.168.10.1:/srv/nfs/hosts/dockstar-1A8AAA,rsize=32768,wsize=32768,hard,intr,v3 ip=192.168.10.11:192.168.10.1::255.255.255.0:dockstar:eth0:off mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) # cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00400000 00020000 "uImage" mtd2: 0fb00000 00020000 "data" # dmesg | grep -i mtd [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/nfs rw rootfstype=nfs rootwait nfsroot=192.168.10.1:/srv/nfs/hosts/dockstar-1A8AAA,rsize=32768,wsize=32768,hard,intr,v3 ip=192.168.10.11:192.168.10.1::255.255.255.0:dockstar:eth0:off mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 2.173189] mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 23.936465] 3 fixed-partitions partitions found on MTD device orion_nand [ 23.943248] Creating 3 MTD partitions on "orion_nand": # dmesg | grep -i 0x000 [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 22.184652] Bad eraseblock 1092 at 0x000008880000 [ 22.337982] Bad eraseblock 1328 at 0x00000a600000 [ 23.982877] 0x000000000000-0x000000100000 : "u-boot" [ 24.006601] 0x000000100000-0x000000500000 : "uImage" [ 24.038402] 0x000000500000-0x000010000000 : "data" # fw_printenv arcNumber=2998 autoload=no baudrate=115200 bootcmd=run net_bootcmd bootcmd.bak=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=3 bootdev=usb console=ttyS0,115200 custom_params=init=/bin/systemd device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-dockstar.dtb ethact=egiga0 ethaddr=00:10:75:1A:8A:AA if_netconsole=ping $serverip ipaddr=192.168.10.11 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x02000000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) net_bootcmd=run net_check_dhcp_c; run net_check_dhcp_s; run net_set_bootargs; run net_bootcmd_exec net_bootcmd_exec=run net_load_uimage; if run net_load_initrd; then if run net_load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi net_check_dhcp_c=if test $net_dhcp_c -eq 1 ; then run net_set_c_ip_dhcp; else run net_set_c_ip_stat; fi;echo ** IP Address: $ipaddr; echo ** Subnet Mask: $netmask; echo ** Def Gateway: $gatewayip net_check_dhcp_s=if test $net_dhcp_s -eq 1 && test $net_dhcp_c -eq 1 ; then run net_set_s_ip_dhcp; else run net_set_s_ip_stat; fi; echo ** NFS Boot Server: $net_nfs_server; echo net_dhcp_c=1 net_dhcp_s=1 net_load_dtb=echo NFS loading DTB :$net_nfs_server:$net_nfs_path/$net_nfs_dtb ... ; nfs $load_dtb_addr $net_nfs_server:$net_nfs_path/$net_nfs_dtb; echo net_load_initrd=echo NFS loading uInitrd :$net_nfs_server:$net_nfs_path/$net_nfs_initrd ...; nfs $load_initrd_addr $net_nfs_server:$net_nfs_path/$net_nfs_initrd; echo net_load_uimage=echo NFS loading uImage :$net_nfs_server:$net_nfs_path/$net_nfs_kernel ...; nfs $load_uimage_addr $net_nfs_server:$net_nfs_path/$net_nfs_kernel; echo net_nfs_dtb=boot/dts/kirkwood-dockstar.dtb net_nfs_initrd=boot/uInitrd net_nfs_kernel=boot/uImage net_nfs_path=/srv/nfs/hosts/dockstar-1A8AAA net_set_bootargs=setenv serverip $net_nfs_server; setenv bootargs console=$console root=/dev/nfs rw rootfstype=nfs rootwait nfsroot=$net_nfs_server:$net_nfs_path,rsize=32768,wsize=32768,hard,intr,v3 ip=$ipaddr:$net_nfs_server:$gatewayip:$netmask:dockstar:eth0:off $mtdparts net_set_c_ip_dhcp=dhcp; echo; echo ** Getting IP Settings by DHCP (net_dhcp_c = 1): net_set_c_ip_stat=setenv ipaddr $net_c_ipaddr; setenv netmask $net_c_netmask; setenv gatewayip $net_c_gatewayip; echo; echo ** Using static IP Settings (net_dhcp_c = 0): net_set_s_ip_dhcp=setenv net_nfs_server $serverip;echo; echo ** Getting NFS Boot Server by DHCP (net_dhcp_s and net_dhcp_c = 1): net_set_s_ip_stat=echo; echo ** Using static NFS Boot Server (net_dhcp_s or net_dhcp_c = 0) : partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run bootcmd; fi rescue_installed=1 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 # cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. (DockStar) # Up to two entries are valid; in this case the redundant # environment sector is assumed present. # Note that "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 # ls -l /dev/mtd* crw------- 1 root root 90, 0 2021-07-31 15:01 /dev/mtd0 crw------- 1 root root 90, 1 2021-07-31 15:01 /dev/mtd0ro crw------- 1 root root 90, 2 2021-07-31 15:01 /dev/mtd1 crw------- 1 root root 90, 3 2021-07-31 15:01 /dev/mtd1ro crw------- 1 root root 90, 4 2021-07-31 15:01 /dev/mtd2 crw------- 1 root root 90, 5 2021-07-31 15:01 /dev/mtd2ro
|
Re: how to set MTDs writeable? December 31, 2021 03:26PM |
Admin Registered: 13 years ago Posts: 18,997 |
diff -Naur --no-dereference a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts 2021-11-25 00:49:08.000000000 -0800
+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts 2021-11-28 17:36:56.143843287 -0800
@@ -79,7 +79,6 @@
partition@0 {
label = "u-boot";
reg = <0x0000000 0x100000>;
- read-only;
};
partition@100000 {
4b. Boot with DTB file embedded in the kernel image.Again, this step 4b is for stock U-Boot only. Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box. Generate the uImage and uInitrd (the kernel files vmlinuz-5.15.5-kirkwood-tld-1 and initrd.img-5.15.5-kirkwood-tld-1 were generated by dpkg in Step 3): cd /boot mv uImage uImage.orig mv uInitrd uInitrd.orig cp -a zImage-5.15.5-kirkwood-tld-1 zImage.fdt cat dts/kirkwood-goflexnet.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.15.5-kirkwood-tld-1 -d zImage.fdt uImage mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-5.15.5-kirkwood-tld-1 -d initrd.img-5.15.5-kirkwood-tld-1 uInitrd
|
Re: how to set MTDs writeable? December 31, 2021 05:46PM |
Registered: 13 years ago Posts: 26 |
|
Re: how to set MTDs writeable? December 31, 2021 06:17PM |
Admin Registered: 13 years ago Posts: 18,997 |