Re: Debian on WD MyCloud EX 4100 June 07, 2017 04:21PM |
Admin Registered: 13 years ago Posts: 19,103 |
Re: Debian on WD MyCloud EX 4100 June 07, 2017 04:26PM |
Admin Registered: 13 years ago Posts: 19,103 |
Re: Debian on WD MyCloud EX 4100 June 07, 2017 07:21PM |
Admin Registered: 13 years ago Posts: 19,103 |
setenv bootdev scsi setenv device '0:1' setenv load_initrd_addr 0x2900000 setenv load_image_addr 0x02000000 setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' setenv sata_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' setenv sata_bootcmd 'echo Booting from SATA ...; setenv fdt_skip_update yes; run load_image; run load_initrd ; run sata_set_bootargs; bootm $load_image_addr $load_initrd_addr' setenv bootcmd_sata 'scsi init; run sata_set_bootargs; run sata_bootcmd; reset' run bootcmd_sata
Re: Debian on WD MyCloud EX 4100 June 08, 2017 01:19AM |
Registered: 7 years ago Posts: 183 |
Marvell>> setenv dtb_file '/boot/dts/armada-385-wd-ex4100.dtb' Marvell>> setenv bootdev scsi Marvell>> setenv device '0:1' Marvell>> setenv load_initr 0x2900000 Marvell>> setenv load_imag2000000 Marvell>> Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> Marvell>> setenv sata_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' Marvell>> Marvell>> setenv sata_bootcmd 'echo Booting from SATA ...; setenv fdt_skip_update yes; run load_image; run load_initrd ; run sata_set_bootargs; bootm $load_image_addr $load_initrd_addr' Marvell>> setenv bootcmd_sata 'scsi init; run sata_set_bootargs; run sata_bootcmd; reset' Marvell>> Marvell>> run bootcmd_sata AHCI init for unit0 SATA link 0 timeout. SATA link 1 timeout. AHCI init for unit1 Target spinup took 0 ms. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (2:0) Vendor: ATA Prod.: ST3250318AS Rev: CC44 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Found 1 device(s). Booting from SATA ... loading Image ... ** No boot file defined ** loading uInitrd ... ** No boot file defined ** ## Booting image at 02000000 ... NAND read: device 0 offset 0x1c800800, size 0xf00000 15728640 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux-388 Created: 2014-12-26 7:32:50 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3934970 Bytes = 3.8 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK stopping USB.. Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #22 SMP Fri Dec 26 15:32:44 CST 2014 a388-2014T30p1 Build-003 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Marvell Armada 380/385/388 (Device Tree), model: Marvell Armada 385 Development Board bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 1 pages/cpu @c09c8000 s8192 r8192 d16384 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65511 Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial PID hash table entries: 4096 (order: -1, 16384 bytes) Dentry cache hash table entries: 131072 (order: 4, 524288 bytes) Inode-cache hash table entries: 65536 (order: 3, 262144 bytes) Memory: 2048MB = 2048MB total Memory: 2085984k/2085984k available, 11168k reserved, 1303552K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff8000 ( 32 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xf0800000 - 0xfff00000 ( 247 MB) lowmem : 0xc0000000 - 0xf0700000 ( 775 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc06d24a0 (6954 kB) .init : 0xc06d8000 - 0xc071a000 ( 264 kB) .data : 0xc071a000 - 0xc0765aa0 ( 303 kB) .bss : 0xc0765aa0 - 0xc07abdb0 ( 281 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p1 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 3188.32 BogoMIPS (lpj=15941632) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 4096 Initializing cgroup subsys devices CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc0531788 - 0xc05317e0 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (6376.65 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized xor: measuring software checksum speed arm4regs : 1721.600 MB/sec 8regs : 1158.400 MB/sec 32regs : 1104.000 MB/sec xor: using function: arm4regs (1721.600 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated Initializing Suspend to RAM bio: create slab <bio-0> at 0 raid6: int32x1 427 MB/s raid6: int32x2 416 MB/s raid6: int32x4 535 MB/s raid6: int32x8 462 MB/s raid6: using algorithm int32x4 (535 MB/s) raid6: using intx1 recovery algorithm mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Switching to clocksource armada_370_xp_clocksource NET: Registered protocol family 2 TCP established hash table entries: 8192 (order: 1, 65536 bytes) TCP bind hash table entries: 8192 (order: 1, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP: reno registered UDP hash table entries: 1024 (order: 0, 32768 bytes) UDP-Lite hash table entries: 1024 (order: 0, 32768 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 8192 (order 0, 32768 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.22) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 1528 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 ahci_mv f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi2 : ahci_mv_platform scsi3 : ahci_mv_platform ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 60 ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 60 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64 Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_read_bbt: bad block at 0x00000dcc0000 nand_read_bbt: bad block at 0x00000fb00000 nand_read_bbt: bad block at 0x000012180000 nand_read_bbt: bad block at 0x0000139a0000 nand_read_bbt: bad block at 0x000017880000 nand_read_bbt: bad block at 0x0000178a0000 nand_read_bbt: bad block at 0x00001a640000 nand_read_bbt: bad block at 0x00001e9c0000 8 cmdlinepart partitions found on MTD device armada-nand Creating 8 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "u-boot" 0x000000500000-0x000000a00000 : "kernel" 0x000000a00000-0x000000f00000 : "uRamdisk" 0x000000f00000-0x00001c800000 : "image.cfs" 0x00001c800000-0x00001d700000 : "rescue_fw" 0x00001d700000-0x00001eb00000 : "config" 0x00001eb00000-0x00001f500000 : "reserve1" 0x00001f500000-0x00001ff00000 : "reserve2" o 3 Giga ports supported o NETA acceleration mode 1 o RX Queue support: 8 Queues * 128 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=0 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o egiga0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) port #1: is_sgmii=1, is_rgmii=0, phy_addr=1 o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048 o Port 1 is connected to Linux netdevice o egiga1, ifindex = 3, GbE port = 1 giga p=1: mtu=1500, mac=00:50:43:02:02:02 (platform) libphy: orion_mdio_bus: probed ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage ata2: SATA link down (SStatus 0 SControl 300) ata1: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: ST3250318AS, CC44, max UDMA/133 ata3.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133 scsi 2:0:0:0: Direct-Access ATA ST3250318AS CC44 PQ: 0 ANSI: 5 sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 2:0:0:0: [sda] Attached SCSI disk usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd usb 3-1: Parent hub missing LPM exit latency info. Power management will be impacted. hub 3-1:1.0: USB hub found hub 3-1:1.0: 4 ports detected mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 usb 2-1: new high-speed USB device number 2 using xhci-hcd md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=64 hub 2-1:1.0: USB hub found armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c06f44b0) hub 2-1:1.0: 4 ports detected TCP: cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 mvebu-rtc f10a3800.rtc: setting system clock to 2017-06-08 06:12:47 UTC (1496902367) Waiting 10sec before mounting root device... md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs (sda1): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) readonly on device 8:1. devtmpfs: mounted Freeing unused kernel memory: 256K (c06d8000 - c0718000) Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevdsystemd-udevd[1325]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 34129/15269888 files, 1138509/61049390 blocks done. EXT3-fs (sda1): using internal journal [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Cannot find device "eth0" Bind socket to interface: No such device If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging.. exiting. Failed to bring up eth0. done. rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 [ ok ] Starting rpcbind daemon.... [FAIL] Starting NFS common utilities: statd idmapd failed! [ ok ] Cleaning up temporary files.... [FAIL] startpar: service(s) returned failure: nfs-common ... failed! INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2290 (syslogd) . ok [ ok ] Starting NTP server: ntpd. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2289 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login:
Re: Debian on WD MyCloud EX 4100 June 08, 2017 01:26AM |
Admin Registered: 13 years ago Posts: 19,103 |
Device 0: (2:0) Vendor: ATA Prod.: ST3250318AS Rev: CC44 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Found 1 device(s). Booting from SATA ...
scsi init ext2ls scsi 0:1 /boot
Re: Debian on WD MyCloud EX 4100 June 08, 2017 01:41AM |
Registered: 7 years ago Posts: 183 |
Marvell>> scsi init AHCI init for unit0 SATA link 0 timeout. SATA link 1 timeout. AHCI init for unit1 Target spinup took 0 ms. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (2:0) Vendor: ATA Prod.: ST3250318AS Rev: CC44 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Found 1 device(s). Marvell>> ext2ls scsi 0:1 /boot <DIR> 4096 . <DIR> 4096 .. 3904400 zImage-4.9.0-mvebu-tld-12 3904400 zImage 6210503 uInitrd 3904400 vmlinuz-4.9.0-mvebu-tld-12 6210439 initrd.img-4.9.0-mvebu-tld-12 2845228 System.map-4.9.0-mvebu-tld-12 <DIR> 4096 dts 3904464 uImage 150531 config-4.9.0-mvebu-tld-12 Marvell>>
Re: Debian on WD MyCloud EX 4100 June 08, 2017 02:21AM |
Admin Registered: 13 years ago Posts: 19,103 |
Booting from SATA ... loading Image ... ** No boot file defined ** loading uInitrd ... ** No boot file defined **
ext2load scsi 0:1 0x02000000 /boot/uImage ext2load scsi 0:1 0x2900000 /boot/uInitrd
Re: Debian on WD MyCloud EX 4100 June 08, 2017 02:52AM |
Registered: 7 years ago Posts: 183 |
> ext2load scsi 0:1 0x02000000 /boot/uImage > ext2load scsi 0:1 0x2900000 /boot/uInitrd >
Marvell>> scsi init AHCI init for unit0 SATA link 0 timeout. SATA link 1 timeout. AHCI init for unit1 Target spinup took 0 ms. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (2:0) Vendor: ATA Prod.: ST3250318AS Rev: CC44 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Found 1 device(s). Marvell>> ext2load scsi 0:1 0x02000000 /boot/uImage 3904464 bytes read in 219 ms (17 MiB/s) Marvell>> ext2load scsi 0:1 0x2900000 /boot/uInitrd 6210503 bytes read in 237 ms (25 MiB/s)
Re: Debian on WD MyCloud EX 4100 June 08, 2017 01:00PM |
Admin Registered: 13 years ago Posts: 19,103 |
setenv load_initrd_addr 0x2900000 setenv load_image_addr 0x02000000 setenv load_initrd 'echo loading uInitrd ...; ext2load scsi 0:1 $load_initrd_addr /boot/uInitrd' setenv load_image 'echo loading Image ...; ext2load scsi 0:1 $load_image_addr /boot/uImage' setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial' setenv fdt_skip_update yes scsi init run load_image run load_initrd bootm $load_image_addr $load_initrd_addr
Re: Debian on WD MyCloud EX 4100 June 08, 2017 01:51PM |
Registered: 7 years ago Posts: 183 |
Marvell>> setenv load_initrd_addr 0x2900000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv dtb_file '/boot/dts/armada-385-wd-ex4100.dtb' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load scsi 0:1 $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load scsi 0:1 $load_image_addr /boot/uImage' Marvell>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial' Marvell>> setenv fdt_skip_update yes Marvell>> scsi init AHCI init for unit0 SATA link 0 timeout. SATA link 1 timeout. AHCI init for unit1 Target spinup took 0 ms. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (2:0) Vendor: ATA Prod.: ST3250318AS Rev: CC44 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Found 1 device(s). Marvell>> run load_image loading Image ... 3904464 bytes read in 218 ms (17.1 MiB/s) Marvell>> run load_initrd loading uInitrd ... 6210503 bytes read in 237 ms (25 MiB/s) Marvell>> bootm $load_image_addr $load_initrd_addr ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-02-04 0:22:26 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3904400 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK stopping USB.. Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000210). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Armada 39x (Device Tree) ffffffff Marvell Armada 380/385 (Device Tree) ffffffff Marvell Armada 375 (Device Tree) ffffffff Marvell Armada 370/XP (Device Tree) ffffffff Marvell Dove Please check your kernel config and/or bootloader.
Re: Debian on WD MyCloud EX 4100 June 08, 2017 02:30PM |
Admin Registered: 13 years ago Posts: 19,103 |
Re: Debian on WD MyCloud EX 4100 June 08, 2017 02:37PM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 08, 2017 02:43PM |
Admin Registered: 13 years ago Posts: 19,103 |
Re: Debian on WD MyCloud EX 4100 June 08, 2017 02:48PM |
Registered: 7 years ago Posts: 183 |
Marvell>> setenv load_initrd_addr 0x2900000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load scsi 0:1 $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load scsi 0:1 $load_image_addr /boot/uImage' Marvell>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial' Marvell>> setenv fdt_skip_update yes Marvell>> scsi init AHCI init for unit0 SATA link 0 timeout. SATA link 1 timeout. AHCI init for unit1 Target spinup took 0 ms. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (2:0) Vendor: ATA Prod.: ST3250318AS Rev: CC44 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Found 1 device(s). Marvell>> run load_image loading Image ... 3919325 bytes read in 192 ms (19.5 MiB/s) Marvell>> run load_initrd loading uInitrd ... 6210503 bytes read in 239 ms (24.8 MiB/s) Marvell>> bootm $load_image_addr $load_initrd_addr ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-06-08 19:40:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3919261 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK stopping USB.. Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: WD My Cloud EX4100 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @eefcd000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2060316K/2097152K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 36836K reserved, 0K cma-reserved, 1310720K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007881] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019058] Console: colour dummy device 80x30 [ 0.023572] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.033976] pid_max: default: 32768 minimum: 301 [ 0.038730] Security Framework initialized [ 0.042924] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.049597] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.057102] CPU: Testing write buffer coherency: ok [ 0.062172] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.067911] Setting up static identity map for 0x100000 - 0x100058 [ 0.074214] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4 [ 0.079473] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283911] Booting CPU 1 [ 0.286757] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286806] Brought up 2 CPUs [ 0.295565] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301885] CPU: All CPU(s) started in SVC mode. [ 0.307118] devtmpfs: initialized [ 0.312401] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320345] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330271] prandom: seed boundary self test passed [ 0.336896] prandom: 100 self tests passed [ 0.341056] pinctrl core: initialized pinctrl subsystem [ 0.346977] NET: Registered protocol family 16 [ 0.352011] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.393867] cpuidle: using governor ladder [ 0.423865] cpuidle: using governor menu [ 0.427931] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.436000] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.441981] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.450135] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.504833] vgaarb: loaded [ 0.507844] SCSI subsystem initialized [ 0.512070] usbcore: registered new interface driver usbfs [ 0.517702] usbcore: registered new interface driver hub [ 0.523126] usbcore: registered new device driver usb [ 0.528447] media: Linux media interface: v0.10 [ 0.533092] Linux video capture interface: v2.00 [ 0.538579] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.569900] VFS: Disk quotas dquot_6.6.0 [ 0.573928] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.587761] NET: Registered protocol family 2 [ 0.592582] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.599731] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.606282] TCP: Hash tables configured (established 8192 bind 8192) [ 0.612750] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.618763] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.625271] NET: Registered protocol family 1 [ 0.629954] RPC: Registered named UNIX socket transport module. [ 0.635930] RPC: Registered udp transport module. [ 0.640710] RPC: Registered tcp transport module. [ 0.645474] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.652100] Unpacking initramfs... [ 0.859227] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.865200] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.871971] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.881124] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.887327] audit: initializing netlink subsys (disabled) [ 0.892840] audit: type=2000 audit(0.880:1): initialized [ 0.898641] Initialise system trusted keyrings [ 0.903278] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.909860] zbud: loaded [ 0.912928] NFS: Registering the id_resolver key type [ 0.918048] Key type id_resolver registered [ 0.922311] Key type id_legacy registered [ 0.926391] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.933166] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.939713] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.947096] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.953721] orangefs_init: module version upstream loaded [ 0.960945] Key type asymmetric registered [ 0.965107] Asymmetric key parser 'x509' registered [ 0.970095] bounce: pool size: 64 pages [ 0.974064] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.981519] io scheduler noop registered [ 0.985506] io scheduler deadline registered [ 0.989871] io scheduler cfq registered (default) [ 0.995440] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.003855] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.010817] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.017140] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.024077] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.030018] PCI: bus0: Fast back to back transfers disabled [ 1.035654] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.043725] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.051903] PCI: bus1: Fast back to back transfers enabled [ 1.057561] PCI: bus2: Fast back to back transfers enabled [ 1.063155] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.068184] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.073647] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.138978] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.146586] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.208984] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.258807] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.266471] console [ttyS0] disabled [ 1.290228] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A [ 1.299276] console [ttyS0] enabled [ 1.299276] console [ttyS0] enabled [ 1.306365] bootconsole [earlycon0] disabled [ 1.306365] bootconsole [earlycon0] disabled [ 1.315975] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.325081] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.334660] scsi host0: ahci-mvebu [ 1.338362] scsi host1: ahci-mvebu [ 1.341991] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.349968] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.358046] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.367146] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.376535] scsi host2: ahci-mvebu [ 1.380179] scsi host3: ahci-mvebu [ 1.383735] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 43 [ 1.391712] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 43 [ 1.400143] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.407975] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc [ 1.414378] nand: Hynix H27U4G8F2DTR-BC [ 1.418231] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.425843] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.433045] Bad block table found at page 262080, version 0x01 [ 1.439233] Bad block table found at page 262016, version 0x01 [ 1.445261] nand_read_bbt: bad block at 0x00000dcc0000 [ 1.450441] nand_read_bbt: bad block at 0x00000fb00000 [ 1.455602] nand_read_bbt: bad block at 0x000012180000 [ 1.460768] nand_read_bbt: bad block at 0x0000139a0000 [ 1.465929] nand_read_bbt: bad block at 0x000017880000 [ 1.471105] nand_read_bbt: bad block at 0x0000178a0000 [ 1.476265] nand_read_bbt: bad block at 0x00001a640000 [ 1.481433] nand_read_bbt: bad block at 0x00001e9c0000 [ 1.486617] 3 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.492752] Creating 3 MTD partitions on "pxa3xx_nand-0": [ 1.498175] 0x000000000000-0x000000800000 : "U-Boot" [ 1.513839] 0x000000800000-0x000001000000 : "Linux" [ 1.529371] 0x000001000000-0x000040000000 : "Filesystem" [ 1.534708] mtd: partition "Filesystem" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x1f000000 [ 1.558621] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.565268] libphy: Fixed MDIO Bus: probed [ 1.569691] libphy: mdio_driver_register: mv88e6085 [ 1.574730] libphy: orion_mdio_bus: probed [ 1.584380] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 1.593439] mvneta f1070000.ethernet eth0: Using random mac address 42:8d:11:83:11:d6 [ 1.602825] mvneta f1030000.ethernet eth1: Using random mac address 52:06:2d:4c:a8:c4 [ 1.610910] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.617477] ehci-pci: EHCI PCI platform driver [ 1.622007] ehci-orion: EHCI orion driver [ 1.626129] orion-ehci f1058000.usb: EHCI Host Controller [ 1.631587] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.639249] orion-ehci f1058000.usb: irq 38, io mem 0xf1058000 [ 1.668599] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.674653] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.681482] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.688753] usb usb1: Product: EHCI Host Controller [ 1.689867] ata1: SATA link down (SStatus 0 SControl 300) [ 1.699091] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 ehci_hcd [ 1.699876] ata2: SATA link down (SStatus 0 SControl 300) [ 1.710992] usb usb1: SerialNumber: f1058000.usb [ 1.715941] hub 1-0:1.0: USB hub found [ 1.719742] hub 1-0:1.0: 1 port detected [ 1.724110] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.729467] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.737047] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.739854] ata4: SATA link down (SStatus 0 SControl 300) [ 1.751078] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000 [ 1.756928] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.763778] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.771039] usb usb2: Product: xHCI Host Controller [ 1.775937] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.782421] usb usb2: SerialNumber: f10f0000.usb3 [ 1.787432] hub 2-0:1.0: USB hub found [ 1.791222] hub 2-0:1.0: 1 port detected [ 1.795324] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.800689] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 1.808256] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.816444] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.823281] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.831133] usb usb3: Product: xHCI Host Controller [ 1.836031] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.842516] usb usb3: SerialNumber: f10f0000.usb3 [ 1.847515] hub 3-0:1.0: USB hub found [ 1.851304] hub 3-0:1.0: 1 port detected [ 1.855469] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.860837] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.868422] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.877014] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000 [ 1.882878] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.889704] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.896956] usb usb4: Product: xHCI Host Controller [ 1.898593] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.908123] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.908131] ata3.00: ATA-8: ST3250318AS, CC44, max UDMA/133 [ 1.908135] ata3.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.926943] usb usb4: SerialNumber: f10f8000.usb3 [ 1.926953] ata3.00: configured for UDMA/133 [ 1.936270] hub 4-0:1.0: USB hub found [ 1.937275] scsi 2:0:0:0: Direct-Access ATA ST3250318AS CC44 PQ: 0 ANSI: 5 [ 1.948194] hub 4-0:1.0: 1 port detected [ 1.952311] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.957651] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 1.965274] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.973469] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.980297] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.987549] usb usb5: Product: xHCI Host Controller [ 1.992454] usb usb5: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.998929] usb usb5: SerialNumber: f10f8000.usb3 [ 2.003938] hub 5-0:1.0: USB hub found [ 2.007719] hub 5-0:1.0: 1 port detected [ 2.009060] sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB) [ 2.009169] sd 2:0:0:0: [sda] Write Protect is off [ 2.009220] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.019359] sda: sda1 [ 2.020046] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 2.041384] usbcore: registered new interface driver usblp [ 2.046963] usbcore: registered new interface driver usb-storage [ 2.053196] mousedev: PS/2 mouse device common for all mice [ 2.059282] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 2.067089] i2c /dev entries driver [ 2.082283] orion_wdt: Initial timeout 171 sec [ 2.087942] marvell-cesa f1090000.crypto: CESA device successfully registered [ 2.095372] hidraw: raw HID events driver (C) Jiri Kosina [ 2.101107] usbcore: registered new interface driver usbhid [ 2.106703] usbhid: USB HID core driver [ 2.110712] drop_monitor: Initializing network drop monitor service [ 2.117034] Netfilter messages via NETLINK v0.30. [ 2.121791] ip_set: protocol 6 [ 2.125029] NET: Registered protocol family 10 [ 2.140052] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.146871] NET: Registered protocol family 17 [ 2.148613] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 2.158066] 8021q: 802.1Q VLAN Support v1.8 [ 2.162298] Key type dns_resolver registered [ 2.166667] ThumbEE CPU extension supported. [ 2.170981] Registering SWP/SWPB emulation handler [ 2.176201] registered taskstats version 1 [ 2.180329] Loading compiled-in X.509 certificates [ 2.185176] zswap: loaded using pool lzo/zbud [ 2.232300] Key type big_key registered [ 2.239558] Key type encrypted registered [ 2.244612] armada38x-rtc f10a3800.rtc: setting system clock to 2017-06-08 19:42:43 UTC (1496950963) [ 2.254792] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.295070] systemd-udevd[1333]: starting version 215 [ 2.301013] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.318864] usb 2-1: New USB device found, idVendor=045b, idProduct=0209 [ 2.325608] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.349292] hub 2-1:1.0: USB hub found [ 2.358642] hub 2-1:1.0: 4 ports detected [ 2.404211] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 2.458803] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.490206] usb 3-1: New USB device found, idVendor=045b, idProduct=0210 [ 2.496962] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.509141] hub 3-1:1.0: USB hub found [ 2.514828] hub 3-1:1.0: 4 ports detected Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 [ 12.651785] random: fast init done fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.673353] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.740602] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 20.387609] systemd-udevd[1536]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 22.069797] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 34131/15269888 files, 1139475/61049390 blocks done. [ 22.498142] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 24.558991] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 24.567775] random: crng init done [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/42:8d:11:83:11:d6 Sending on LPF/eth0/42:8d:11:83:11:d6 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 2 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2490 (syslogd) . ok [ ok ] Starting NTP server: ntpd. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2493 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login:
Re: Debian on WD MyCloud EX 4100 June 08, 2017 03:40PM |
Admin Registered: 13 years ago Posts: 19,103 |
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 ${mtdparts} earlyprintk=serial'If the above did not work then, use
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $(mtdparts) earlyprintk=serial'If the above did not work then, use
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial'
cat /proc/mtd
cat /etc/fw_env.config
fw_printenv
Re: Debian on WD MyCloud EX 4100 June 09, 2017 03:36AM |
Registered: 7 years ago Posts: 183 |
> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 ${mtdparts} earlyprintk=serial' >
> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $(mtdparts) earlyprintk=serial' >
> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro ,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs ),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial' >
Re: Debian on WD MyCloud EX 4100 June 09, 2017 01:35PM |
Admin Registered: 13 years ago Posts: 19,103 |
> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro ,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs ),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial'
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial
Re: Debian on WD MyCloud EX 4100 June 09, 2017 03:15PM |
Registered: 7 years ago Posts: 183 |
Marvell>> setenv load_initrd_addr 0x2900000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load scsi 0:1 $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load scsi 0:1 $load_image_addr /boot/uImage' Marvell>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial' Marvell>> setenv fdt_skip_update yes Marvell>> scsi init AHCI init for unit0 SATA link 0 timeout. SATA link 1 timeout. AHCI init for unit1 Target spinup took 0 ms. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (2:0) Vendor: ATA Prod.: ST3250318AS Rev: CC44 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Found 1 device(s). Marvell>> run load_image loading Image ... 3919325 bytes read in 200 ms (18.7 MiB/s) Marvell>> run load_initrd loading uInitrd ... 6210503 bytes read in 237 ms (25 MiB/s) Marvell>> bootm $load_image_addr $load_initrd_addr ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-06-08 19:40:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3919261 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK stopping USB.. Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: WD My Cloud EX4100 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @eefcd000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2060316K/2097152K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 36836K reserved, 0K cma-reserved, 1310720K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007881] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019057] Console: colour dummy device 80x30 [ 0.023572] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.033976] pid_max: default: 32768 minimum: 301 [ 0.038729] Security Framework initialized [ 0.042922] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.049595] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.057098] CPU: Testing write buffer coherency: ok [ 0.062167] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.067904] Setting up static identity map for 0x100000 - 0x100058 [ 0.074208] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4 [ 0.079468] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283913] Booting CPU 1 [ 0.286759] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286808] Brought up 2 CPUs [ 0.295567] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301887] CPU: All CPU(s) started in SVC mode. [ 0.307120] devtmpfs: initialized [ 0.312412] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320353] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330278] prandom: seed boundary self test passed [ 0.336903] prandom: 100 self tests passed [ 0.341063] pinctrl core: initialized pinctrl subsystem [ 0.346986] NET: Registered protocol family 16 [ 0.352028] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.393869] cpuidle: using governor ladder [ 0.423867] cpuidle: using governor menu [ 0.427933] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.436002] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.441981] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.450136] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.514854] vgaarb: loaded [ 0.517846] SCSI subsystem initialized [ 0.522072] usbcore: registered new interface driver usbfs [ 0.527692] usbcore: registered new interface driver hub [ 0.533116] usbcore: registered new device driver usb [ 0.538432] media: Linux media interface: v0.10 [ 0.543077] Linux video capture interface: v2.00 [ 0.548565] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.579917] VFS: Disk quotas dquot_6.6.0 [ 0.583945] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.597986] NET: Registered protocol family 2 [ 0.602784] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.609929] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.616479] TCP: Hash tables configured (established 8192 bind 8192) [ 0.622935] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.628940] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.635445] NET: Registered protocol family 1 [ 0.640110] RPC: Registered named UNIX socket transport module. [ 0.646086] RPC: Registered udp transport module. [ 0.650861] RPC: Registered tcp transport module. [ 0.655625] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.662237] Unpacking initramfs... [ 0.869212] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.875186] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.881955] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.891115] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.897319] audit: initializing netlink subsys (disabled) [ 0.902823] audit: type=2000 audit(0.890:1): initialized [ 0.908619] Initialise system trusted keyrings [ 0.913252] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.919822] zbud: loaded [ 0.922885] NFS: Registering the id_resolver key type [ 0.928003] Key type id_resolver registered [ 0.932265] Key type id_legacy registered [ 0.936345] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.943107] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.949653] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.957035] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.963647] orangefs_init: module version upstream loaded [ 0.970942] Key type asymmetric registered [ 0.975104] Asymmetric key parser 'x509' registered [ 0.980080] bounce: pool size: 64 pages [ 0.984052] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.991507] io scheduler noop registered [ 0.995494] io scheduler deadline registered [ 0.999847] io scheduler cfq registered (default) [ 1.005410] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.013841] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.020787] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.027109] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.034043] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.039968] PCI: bus0: Fast back to back transfers disabled [ 1.045604] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.053672] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.061838] PCI: bus1: Fast back to back transfers enabled [ 1.067498] PCI: bus2: Fast back to back transfers enabled [ 1.073090] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.078119] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.083568] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.148970] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.156578] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.218965] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.269402] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.277058] console [ttyS0] disabled [ 1.300788] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A [ 1.309822] console [ttyS0] enabled [ 1.309822] console [ttyS0] enabled [ 1.316909] bootconsole [earlycon0] disabled [ 1.316909] bootconsole [earlycon0] disabled [ 1.326514] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.335621] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.345187] scsi host0: ahci-mvebu [ 1.348889] scsi host1: ahci-mvebu [ 1.352496] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.360459] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.368542] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.377646] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.387025] scsi host2: ahci-mvebu [ 1.400679] scsi host3: ahci-mvebu [ 1.404248] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 43 [ 1.412213] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 43 [ 1.420641] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.428491] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc [ 1.434908] nand: Hynix H27U4G8F2DTR-BC [ 1.438807] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.446411] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.453604] Bad block table found at page 262080, version 0x01 [ 1.459793] Bad block table found at page 262016, version 0x01 [ 1.465821] nand_read_bbt: bad block at 0x00000dcc0000 [ 1.470991] nand_read_bbt: bad block at 0x00000fb00000 [ 1.476151] nand_read_bbt: bad block at 0x000012180000 [ 1.481318] nand_read_bbt: bad block at 0x0000139a0000 [ 1.486479] nand_read_bbt: bad block at 0x000017880000 [ 1.491643] nand_read_bbt: bad block at 0x0000178a0000 [ 1.496803] nand_read_bbt: bad block at 0x00001a640000 [ 1.501970] nand_read_bbt: bad block at 0x00001e9c0000 [ 1.507162] 3 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.513287] Creating 3 MTD partitions on "pxa3xx_nand-0": [ 1.518717] 0x000000000000-0x000000800000 : "U-Boot" [ 1.524366] 0x000000800000-0x000001000000 : "Linux" [ 1.539900] 0x000001000000-0x000040000000 : "Filesystem" [ 1.545236] mtd: partition "Filesystem" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x1f000000 [ 1.569123] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.575771] libphy: Fixed MDIO Bus: probed [ 1.580181] libphy: mdio_driver_register: mv88e6085 [ 1.585218] libphy: orion_mdio_bus: probed [ 1.594992] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 1.604039] mvneta f1070000.ethernet eth0: Using random mac address de:89:bf:74:98:f1 [ 1.613433] mvneta f1030000.ethernet eth1: Using random mac address 42:e3:60:15:2d:96 [ 1.621493] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.628059] ehci-pci: EHCI PCI platform driver [ 1.632574] ehci-orion: EHCI orion driver [ 1.636693] orion-ehci f1058000.usb: EHCI Host Controller [ 1.642139] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.649803] orion-ehci f1058000.usb: irq 38, io mem 0xf1058000 [ 1.678573] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.684632] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.691472] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.698741] usb usb1: Product: EHCI Host Controller [ 1.699909] ata1: SATA link down (SStatus 0 SControl 300) [ 1.709088] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 ehci_hcd [ 1.710015] ata2: SATA link down (SStatus 0 SControl 300) [ 1.720996] usb usb1: SerialNumber: f1058000.usb [ 1.725945] hub 1-0:1.0: USB hub found [ 1.729748] hub 1-0:1.0: 1 port detected [ 1.734126] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.739494] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.747085] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.755687] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000 [ 1.761552] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.768380] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.775649] ata4: SATA link down (SStatus 0 SControl 300) [ 1.781110] usb usb2: Product: xHCI Host Controller [ 1.786008] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.792484] usb usb2: SerialNumber: f10f0000.usb3 [ 1.797500] hub 2-0:1.0: USB hub found [ 1.801295] hub 2-0:1.0: 1 port detected [ 1.805394] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.810747] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 1.818314] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.826504] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.833331] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.840687] usb usb3: Product: xHCI Host Controller [ 1.845586] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.852064] usb usb3: SerialNumber: f10f0000.usb3 [ 1.857063] hub 3-0:1.0: USB hub found [ 1.860852] hub 3-0:1.0: 1 port detected [ 1.865016] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.870371] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.877954] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.886545] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000 [ 1.892402] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.899228] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.906482] usb usb4: Product: xHCI Host Controller [ 1.911427] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.917895] usb usb4: SerialNumber: f10f8000.usb3 [ 1.918577] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.928855] ata3.00: ATA-8: ST3250318AS, CC44, max UDMA/133 [ 1.934507] ata3.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.934632] hub 4-0:1.0: USB hub found [ 1.934648] hub 4-0:1.0: 1 port detected [ 1.934811] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.934818] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 1.934860] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.934918] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.934922] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.934924] usb usb5: Product: xHCI Host Controller [ 1.934927] usb usb5: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.934929] usb usb5: SerialNumber: f10f8000.usb3 [ 1.941486] hub 5-0:1.0: USB hub found [ 1.941503] hub 5-0:1.0: 1 port detected [ 1.941802] usbcore: registered new interface driver usblp [ 1.941897] usbcore: registered new interface driver usb-storage [ 1.949090] mousedev: PS/2 mouse device common for all mice [ 1.954487] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 1.954634] i2c /dev entries driver [ 1.984530] orion_wdt: Initial timeout 171 sec [ 1.985832] marvell-cesa f1090000.crypto: CESA device successfully registered [ 1.985940] hidraw: raw HID events driver (C) Jiri Kosina [ 1.989569] usbcore: registered new interface driver usbhid [ 1.989571] usbhid: USB HID core driver [ 1.989682] drop_monitor: Initializing network drop monitor service [ 1.989711] Netfilter messages via NETLINK v0.30. [ 1.989723] ip_set: protocol 6 [ 1.996172] NET: Registered protocol family 10 [ 2.008837] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.009659] NET: Registered protocol family 17 [ 2.009800] 8021q: 802.1Q VLAN Support v1.8 [ 2.009823] Key type dns_resolver registered [ 2.009908] ThumbEE CPU extension supported. [ 2.009914] Registering SWP/SWPB emulation handler [ 2.033596] registered taskstats version 1 [ 2.033599] Loading compiled-in X.509 certificates [ 2.033634] zswap: loaded using pool lzo/zbud [ 2.088400] Key type big_key registered [ 2.105892] Key type encrypted registered [ 2.114814] armada38x-rtc f10a3800.rtc: setting system clock to 2017-06-09 20:08:48 UTC (1497038928) [ 2.142371] ata3.00: configured for UDMA/133 [ 2.158590] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 2.167026] scsi 2:0:0:0: Direct-Access ATA ST3250318AS CC44 PQ: 0 ANSI: 5 [ 2.248901] sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB) [ 2.256684] sd 2:0:0:0: [sda] Write Protect is off [ 2.261571] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.282400] sda: sda1 [ 2.285403] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 2.291549] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.328873] usb 2-1: New USB device found, idVendor=045b, idProduct=0209 [ 2.335631] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.343399] systemd-udevd[1333]: starting version 215 [ 2.344276] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.361225] hub 2-1:1.0: USB hub found [ 2.365053] hub 2-1:1.0: 4 ports detected [ 2.425824] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 2.468833] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.500161] usb 3-1: New USB device found, idVendor=045b, idProduct=0210 [ 2.506940] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.520072] hub 3-1:1.0: USB hub found [ 2.524135] hub 3-1:1.0: 4 ports detected Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 [ 12.643333] random: fast init done fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.673293] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.683568] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 17.690491] EXT4-fs (sda1): write access will be enabled during recovery [ 17.850533] EXT4-fs (sda1): recovery complete [ 17.881241] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 20.465754] systemd-udevd[1536]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 22.081443] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 34135/15269888 files, 1139490/61049390 blocks done. [ 22.509696] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 24.389135] random: crng init done [ 24.538975] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/de:89:bf:74:98:f1 Sending on LPF/eth0/de:89:bf:74:98:f1 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2497 (syslogd) . ok [ ok ] Starting NTP server: ntpd. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2496 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login: root Password: Last login: Wed Jun 7 23:18:44 PDT 2017 on ttyS0 Linux debian 4.9.0-mvebu-tld-12 #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian WD My Cloud EX4100 Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 13:12:52 up 4 min, 1 user, load average: 0.08, 0.03, 0.01 root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00800000 00020000 "U-Boot" mtd1: 00800000 00020000 "Linux" mtd2: 1f000000 00020000 "Filesystem" root@debian:~#
Re: Debian on WD MyCloud EX 4100 June 09, 2017 03:22PM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 09, 2017 03:24PM |
Admin Registered: 13 years ago Posts: 19,103 |
8 ofpart partitions found on MTD device armada-nand Creating 8 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "U-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "uRamdisk" 0x000000f00000-0x00001c800000 : "image.cfs" 0x00001c800000-0x00001d700000 : "rescue fw" 0x00001d700000-0x00001eb00000 : "config" 0x00001eb00000-0x00001f500000 : "reserve1" 0x00001f500000-0x00001ff00000 : "reserve2"
Re: Debian on WD MyCloud EX 4100 June 09, 2017 03:26PM |
Admin Registered: 13 years ago Posts: 19,103 |
> > cat /etc/fw_env.config > >>
cat /proc/mtd cat /etc/fv_env.config fw_printenv
Re: Debian on WD MyCloud EX 4100 June 09, 2017 03:32PM |
Registered: 7 years ago Posts: 183 |
> cat /proc/mtd > cat /etc/fv_env.config > fw_printenv >
Re: Debian on WD MyCloud EX 4100 June 09, 2017 06:53PM |
Admin Registered: 13 years ago Posts: 19,103 |
setenv mtdparts 'mtdparts=pxa3xx_nand-0:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2)'
Re: Debian on WD MyCloud EX 4100 June 09, 2017 07:43PM |
Admin Registered: 13 years ago Posts: 19,103 |
Quote
u-boot-a38x-Yellowstone_2014T30p6_bodhi-tld-1-nand-uart.bin
./kwboot -f -t -B 115200 /dev/ttyUSB0 -b u-boot-a38x-Yellowstone_2014T30p6_bodhi-tld-1-nand-uart.bin -s 0 -q 1
Re: Debian on WD MyCloud EX 4100 June 10, 2017 05:07AM |
Registered: 7 years ago Posts: 183 |
> setenv mtdparts 'mtdparts=pxa3xx_nand-0:5m(u-boot) > ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.c > fs),15m@456m(rescue_fw),20m@471m(config),10m@491m( > reserve1),10m@501m(reserve2)' >
Re: Debian on WD MyCloud EX 4100 June 10, 2017 05:15AM |
Admin Registered: 13 years ago Posts: 19,103 |
Re: Debian on WD MyCloud EX 4100 June 10, 2017 05:30AM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 10, 2017 06:27AM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 10, 2017 08:12AM |
Registered: 7 years ago Posts: 119 |
--- a/armada-385-wd.dts 2017-06-10 15:14:06.992723200 +0200 +++ b/armada-385-ex2u.dts 2017-06-10 15:13:20.936057940 +0200 @@ -17,11 +17,11 @@ #include <dt-bindings/gpio/gpio.h> / { - model = "Western Digital MyCloud EX2 Ultra"; + model = "Marvell Armada 385 Development Board"; compatible = "marvell,a385-db", "marvell,armada385", "marvell,armada38x"; chosen { - bootargs = "console=ttyS0,115200 libata.force=3.0G root=LABEL=rootfs earlyprintk"; + bootargs = "console=ttyS0,115200 root=LABEL=rootfs earlyprintk"; }; memory { @@ -103,23 +103,14 @@ no-1-8-v; }; - serial@12000 { - status = "okay"; - }; - - /* ttyS1 is connected to w Welltrend 6703F-OG240WT Micocontroller - * which controls power fan and other things */ serial@12100 { status = "okay"; }; - - poweroff@12100 { - compatible = "wdmcex2u,power-off"; - reg = <0x12100 0x100>; - clocks = <&coreclk 0>; + + serial@12000 { status = "okay"; }; - + spi0: spi@10600 { status = "okay"; @@ -228,34 +219,5 @@ }; - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&sata_leds>; - pinctrl-names = "default"; - - red-sata1-led { - label = "wdmcex2u:red:hdd1"; - gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; - }; - red-sata2-led { - label = "wdmcex2u:red:hdd2"; - gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>; - }; - blue-sata1-led { - label = "wdmcex2u:blue:hdd1"; - gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; - }; - blue-sata2-led { - label = "wdmcex2u:blue:hdd2"; - gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; - }; - }; - }; -&pinctrl { - sata_leds: sata-leds { - marvell,pins = "mpp43", "mpp52", "mpp53", "mpp54"; - marvell,function = "gpio"; - }; -};
Re: Debian on WD MyCloud EX 4100 June 10, 2017 01:27PM |
Admin Registered: 13 years ago Posts: 19,103 |
setenv mtdparts 'mtdparts=armada-nand-0:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2)'