Re: Debian on WD MyCloud EX 4100 June 11, 2017 10:03AM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 11, 2017 02:40PM |
Admin Registered: 13 years ago Posts: 18,994 |
Re: Debian on WD MyCloud EX 4100 June 11, 2017 02:44PM |
Admin Registered: 13 years ago Posts: 18,994 |
> sudo ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-bo > ot-a38x-Yellowstone_2014T30p6_bodhi-tld-1-nand-uar > t.bin -s 0 -q 1>
> CASset=max > MALLOC_len=5 > MPmode=SMP > autoload=no > baudrate=115200 > boot_order=hd_scr usb_scr mmc_scr hd_img usb_img m > mc_img pxe net_img net_scr > bootargs=root=/dev/ram console=ttyS0,115200 > bootargs_dflt=$console $nandEcc $mtdparts $bootarg > s_root nfsroot=$serverip:$rootpath ip=$ipaddr:$ser > verip$bootargs_end $mvNetConfig video=dovefb:lcd0: > $lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lc > d_panel=$lcd_panel > bootargs_end=:10.4.50.254:255.255.255.0:Armada38x: > eth0:none > bootargs_root=root=/dev/nfs rw > bootcmd=nand read.e 0xa00000 0x500000 0x500000;nan > d read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 > 0xf00000 > bootcmd_auto=stage_boot $boot_order > bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboo > t $fdtaddr $fdtfile;setenv bootargs $console $nand > Ecc $mtdparts $bootargs_root nfsroot=$serverip:$ro > otpath ip=$ipaddr:$serverip$bootargs_end $mvNetCon > fig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enabl > e=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x > 2000000 - $fdtaddr; > bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; s > etenv bootargs $console $nandEcc $mtdparts $bootar > gs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$se > rverip$bootargs_end $mvNetConfig video=dovefb:lcd0 > :$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.l > cd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; > bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt a > ddr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot > bootcmd_lgcy=tftpboot 0x2000000 $image_name; seten > v bootargs $bootargs_dflt; bootm 0x2000000; > bootdelay=1 > cacheShare=no > console=console=ttyS0,115200 > device_partition=0:1 > disaMvPnp=no > eeeEnable=no > enaClockGating=no > enaCpuStream=no > enaFPU=yes > enaMonExt=no > enaWrAllo=no > eth1addr=00:50:43:58:31:3c > eth1mtu=1500 > eth2addr=00:50:43:58:54:3c > eth2mtu=1500 > eth3addr=00:50:43:31:54:58 > eth3mtu=1500 > ethact=egiga0 > ethaddr=00:50:43:54:31:3c > ethmtu=1500 > ethprime=egiga0 > fdt_addr=2040000 > fdt_skip_update=no > fdtaddr=0x1000000 > fdtfile=armada-38x-modular.dtb > filesize=24 > ide_path=/ > image_name=uImage > initrd_name=uInitrd > ipaddr=2.66.66.203 > kernel_addr_r=2080000 > lcd0_enable=0 > lcd0_params=640x480-16@60 > lcd_panel=0 > loadaddr=0x02000000 > loads_echo=0 > mtddevname=u-boot > mtddevnum=0 > mtdids=nand0=armada-nand > mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(k > ernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@45 > 6m(rescue_fw),20m@471m(config),10m@491m(reserve1), > 10m@501m(reserve2) > mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1 > :2:3),mtu=1500 > mv_pon_addr=00:50:43:3c:54:58 > nandEcc=nfcConfig=4bitecc > netbsd_en=no > netmask=255.255.255.0 > netretry=no > partition=nand0,0 > pcieTune=no > pexMode=RC > pxe_files_load=:default.arm-armadaxp-db:default.ar > m-armadaxp:default.arm > pxefile_addr_r=3100000 > ramdisk_addr_r=2880000 > rootpath=/srv/nfs/ > sata_delay_reset=0 > sata_dma_mode=yes > script_addr_r=3000000 > script_name=boot.scr > serverip=2.66.66.32 > standalone=fsload 0x2000000 $image_name;setenv boo > targs $console $nandEcc $mtdparts root=/dev/mtdblo > ck0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x > 2000000; > stderr=serial > stdin=serial > stdout=serial > usb0Mode=host > usbActive=0 > usbType=3 > vxworks_en=no > yuk_ethaddr=00:00:00:EE:51:81 > > Environment size: 3202/524284 bytes
Re: Debian on WD MyCloud EX 4100 June 11, 2017 03:48PM |
Registered: 7 years ago Posts: 183 |
printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_usb=usb start; run usb_set_bootargs; run usb_bootcmd; reset bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:40:41:2a eth1mtu=1500 eth2addr=00:50:43:40:96:2a eth2mtu=1500 eth3addr=00:50:43:41:96:40 eth3mtu=1500 ethact=egiga0 ethaddr=00:50:43:96:41:2a ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=24 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=2.66.66.203 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:2a:96:40 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=2.66.66.32 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_bootcmd=echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_initrd ; run usb_set_bootargs; bootm $load_image_addr $load_initrd_addr usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3840/524284 bytes Marvell>> run bootcmd_usb (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3919325 bytes read in 324 ms (11.5 MiB/s) loading uInitrd ... 6210503 bytes read in 347 ms (17.1 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-06-04 8:57:41 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3919261 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: WD My Cloud EX4100 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @eefcd000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2060316K/2097152K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 36836K reserved, 0K cma-reserved, 1310720K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007881] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019057] Console: colour dummy device 80x30 [ 0.023571] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.033975] pid_max: default: 32768 minimum: 301 [ 0.038728] Security Framework initialized [ 0.042921] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.049594] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.057095] CPU: Testing write buffer coherency: ok [ 0.062164] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.067901] Setting up static identity map for 0x100000 - 0x100058 [ 0.074205] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4 [ 0.079464] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283911] Booting CPU 1 [ 0.286756] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286804] Brought up 2 CPUs [ 0.295563] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301882] CPU: All CPU(s) started in SVC mode. [ 0.307113] devtmpfs: initialized [ 0.312392] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320336] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330262] prandom: seed boundary self test passed [ 0.336887] prandom: 100 self tests passed [ 0.341047] pinctrl core: initialized pinctrl subsystem [ 0.346972] NET: Registered protocol family 16 [ 0.352006] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.393868] cpuidle: using governor ladder [ 0.423866] cpuidle: using governor menu [ 0.427933] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.436002] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.441981] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.450136] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.504832] vgaarb: loaded [ 0.507840] SCSI subsystem initialized [ 0.512067] usbcore: registered new interface driver usbfs [ 0.517697] usbcore: registered new interface driver hub [ 0.523121] usbcore: registered new device driver usb [ 0.528441] media: Linux media interface: v0.10 [ 0.533084] Linux video capture interface: v2.00 [ 0.538571] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.570140] VFS: Disk quotas dquot_6.6.0 [ 0.574168] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.587983] NET: Registered protocol family 2 [ 0.592805] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.599953] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.606504] TCP: Hash tables configured (established 8192 bind 8192) [ 0.612976] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.618986] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.625490] NET: Registered protocol family 1 [ 0.630170] RPC: Registered named UNIX socket transport module. [ 0.636146] RPC: Registered udp transport module. [ 0.640926] RPC: Registered tcp transport module. [ 0.645690] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.652315] Unpacking initramfs... [ 0.859337] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.865311] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.872078] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.881235] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.887439] audit: initializing netlink subsys (disabled) [ 0.892952] audit: type=2000 audit(0.880:1): initialized [ 0.898751] Initialise system trusted keyrings [ 0.903397] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.909975] zbud: loaded [ 0.913042] NFS: Registering the id_resolver key type [ 0.918161] Key type id_resolver registered [ 0.922422] Key type id_legacy registered [ 0.926501] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.933264] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.939808] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.947188] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.953802] orangefs_init: module version upstream loaded [ 0.961115] Key type asymmetric registered [ 0.965278] Asymmetric key parser 'x509' registered [ 0.970255] bounce: pool size: 64 pages [ 0.974227] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.981681] io scheduler noop registered [ 0.985669] io scheduler deadline registered [ 0.990022] io scheduler cfq registered (default) [ 0.995588] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.004001] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.010948] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.017270] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.024205] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.030132] PCI: bus0: Fast back to back transfers disabled [ 1.035768] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.043836] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.052001] PCI: bus1: Fast back to back transfers enabled [ 1.057657] PCI: bus2: Fast back to back transfers enabled [ 1.063250] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.068279] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.073727] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.138977] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.146584] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.208971] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.259835] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.267475] console [ttyS0] disabled [ 1.291204] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A [ 1.300237] console [ttyS0] enabled [ 1.300237] console [ttyS0] enabled [ 1.307324] bootconsole [earlycon0] disabled [ 1.307324] bootconsole [earlycon0] disabled [ 1.316913] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.326019] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.335566] scsi host0: ahci-mvebu [ 1.339289] scsi host1: ahci-mvebu [ 1.342897] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.350862] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.358950] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.368038] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.387423] scsi host2: ahci-mvebu [ 1.391069] scsi host3: ahci-mvebu [ 1.394627] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 43 [ 1.402591] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 43 [ 1.411046] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.418913] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc [ 1.425294] nand: Hynix H27U4G8F2DTR-BC [ 1.429173] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.436777] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.443968] Bad block table found at page 262080, version 0x01 [ 1.450155] Bad block table found at page 262016, version 0x01 [ 1.456182] nand_read_bbt: bad block at 0x00000dcc0000 [ 1.461352] nand_read_bbt: bad block at 0x00000fb00000 [ 1.466512] nand_read_bbt: bad block at 0x000012180000 [ 1.471680] nand_read_bbt: bad block at 0x0000139a0000 [ 1.476841] nand_read_bbt: bad block at 0x000017880000 [ 1.482005] nand_read_bbt: bad block at 0x0000178a0000 [ 1.487166] nand_read_bbt: bad block at 0x00001a640000 [ 1.492331] nand_read_bbt: bad block at 0x00001e9c0000 [ 1.497523] 3 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.503649] Creating 3 MTD partitions on "pxa3xx_nand-0": [ 1.509080] 0x000000000000-0x000000800000 : "U-Boot" [ 1.524743] 0x000000800000-0x000001000000 : "Linux" [ 1.540277] 0x000001000000-0x000040000000 : "Filesystem" [ 1.545613] mtd: partition "Filesystem" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x1f000000 [ 1.569457] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.576102] libphy: Fixed MDIO Bus: probed [ 1.580513] libphy: mdio_driver_register: mv88e6085 [ 1.585551] libphy: orion_mdio_bus: probed [ 1.595074] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 1.604120] mvneta f1070000.ethernet eth0: Using random mac address 42:55:87:01:d3:d2 [ 1.613514] mvneta f1030000.ethernet eth1: Using random mac address b2:19:be:01:48:46 [ 1.621575] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.628142] ehci-pci: EHCI PCI platform driver [ 1.632656] ehci-orion: EHCI orion driver [ 1.636776] orion-ehci f1058000.usb: EHCI Host Controller [ 1.642238] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.649911] orion-ehci f1058000.usb: irq 38, io mem 0xf1058000 [ 1.678580] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.684639] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.689866] ata1: SATA link down (SStatus 0 SControl 300) [ 1.696919] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.700004] ata2: SATA link down (SStatus 0 SControl 300) [ 1.709619] usb usb1: Product: EHCI Host Controller [ 1.714517] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 ehci_hcd [ 1.720998] usb usb1: SerialNumber: f1058000.usb [ 1.725949] hub 1-0:1.0: USB hub found [ 1.729750] hub 1-0:1.0: 1 port detected [ 1.734128] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.739496] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.747086] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.749845] ata4: SATA link down (SStatus 0 SControl 300) [ 1.755668] ata3: SATA link down (SStatus 0 SControl 300) [ 1.766549] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000 [ 1.772407] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.779248] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.786500] usb usb2: Product: xHCI Host Controller [ 1.791407] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.797874] usb usb2: SerialNumber: f10f0000.usb3 [ 1.802891] hub 2-0:1.0: USB hub found [ 1.806675] hub 2-0:1.0: 1 port detected [ 1.810787] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.816127] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 1.823701] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.831895] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.838795] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.846048] usb usb3: Product: xHCI Host Controller [ 1.850955] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.857423] usb usb3: SerialNumber: f10f0000.usb3 [ 1.862427] hub 3-0:1.0: USB hub found [ 1.866206] hub 3-0:1.0: 1 port detected [ 1.870381] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.875726] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.883319] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.891912] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000 [ 1.897762] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.904588] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.911848] usb usb4: Product: xHCI Host Controller [ 1.916745] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.923255] usb usb4: SerialNumber: f10f8000.usb3 [ 1.928273] hub 4-0:1.0: USB hub found [ 1.932066] hub 4-0:1.0: 1 port detected [ 1.936164] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.941516] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 1.949078] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.957260] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.964087] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.971347] usb usb5: Product: xHCI Host Controller [ 1.976244] usb usb5: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.982763] usb usb5: SerialNumber: f10f8000.usb3 [ 1.987760] hub 5-0:1.0: USB hub found [ 1.991551] hub 5-0:1.0: 1 port detected [ 1.995735] usbcore: registered new interface driver usblp [ 2.001325] usbcore: registered new interface driver usb-storage [ 2.007527] mousedev: PS/2 mouse device common for all mice [ 2.013489] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 2.021169] i2c /dev entries driver [ 2.035979] orion_wdt: Initial timeout 171 sec [ 2.041652] marvell-cesa f1090000.crypto: CESA device successfully registered [ 2.048942] hidraw: raw HID events driver (C) Jiri Kosina [ 2.054541] usbcore: registered new interface driver usbhid [ 2.060151] usbhid: USB HID core driver [ 2.064122] drop_monitor: Initializing network drop monitor service [ 2.070458] Netfilter messages via NETLINK v0.30. [ 2.075189] ip_set: protocol 6 [ 2.078423] NET: Registered protocol family 10 [ 2.083449] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.090238] NET: Registered protocol family 17 [ 2.094817] 8021q: 802.1Q VLAN Support v1.8 [ 2.099173] Key type dns_resolver registered [ 2.103544] ThumbEE CPU extension supported. [ 2.107835] Registering SWP/SWPB emulation handler [ 2.112984] registered taskstats version 1 [ 2.117099] Loading compiled-in X.509 certificates [ 2.121951] zswap: loaded using pool lzo/zbud [ 2.168604] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 2.175303] Key type big_key registered [ 2.182615] Key type encrypted registered [ 2.187575] armada38x-rtc f10a3800.rtc: setting system clock to 2017-06-11 20:37:51 UTC (1497213471) [ 2.197757] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.236254] systemd-udevd[1323]: starting version 215 [ 2.242189] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.348852] usb 2-1: New USB device found, idVendor=045b, idProduct=0209 [ 2.355595] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.363228] hub 2-1:1.0: USB hub found [ 2.372238] hub 2-1:1.0: 4 ports detected [ 2.488851] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.530176] usb 3-1: New USB device found, idVendor=045b, idProduct=0210 [ 2.536912] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.544734] hub 3-1:1.0: USB hub found [ 2.548750] hub 3-1:1.0: 4 ports detected [ 2.698592] usb 2-1.3: new high-speed USB device number 3 using xhci-hcd [ 2.829218] usb 2-1.3: New USB device found, idVendor=0781, idProduct=5571 [ 2.836124] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.843478] usb 2-1.3: Product: Cruzer Fit [ 2.847591] usb 2-1.3: Manufacturer: SanDisk [ 2.851886] usb 2-1.3: SerialNumber: 4C530302071223122304 [ 2.857813] usb-storage 2-1.3:1.0: USB Mass Storage device detected [ 2.874294] scsi host4: usb-storage 2-1.3:1.0 [ 2.880510] usbcore: registered new interface driver uas [ 3.929102] scsi 4:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6 [ 3.939076] sd 4:0:0:0: [sda] 61489152 512-byte logical blocks: (31.5 GB/29.3 GiB) [ 3.947603] sd 4:0:0:0: Attached scsi generic sg0 type 0 [ 3.952973] sd 4:0:0:0: [sda] Write Protect is off [ 3.958552] sd 4:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.970868] sda: sda1 [ 3.979382] sd 4:0:0:0: [sda] Attached SCSI removable disk [ 3.994042] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.663632] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.679396] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 18.443139] systemd-udevd[1530]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 19.906781] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 34130/1925120 files, 299583/7685888 blocks done. [ 20.024095] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 21.088975] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/42:55:87:01:d3:d2 Sending on LPF/eth0/42:55:87:01:d3:d2 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. [....] Starting [ 82.595771] random: crng init done [ ok nd daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2455 (syslogd) . ok [ ok ] Starting NTP server: ntpd. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2454 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login: root Password: Last login: Fri Feb 3 22:22:51 PST 2017 from 192.168.0.100 on pts/0 Linux debian 4.9.0-mvebu-tld-12 #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian WD My Cloud EX4100 Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 13:39:53 up 2 min, 1 user, load average: 0.03, 0.02, 0.00 root@debian:~#
Re: Debian on WD MyCloud EX 4100 June 11, 2017 04:07PM |
Admin Registered: 13 years ago Posts: 18,994 |
Re: Debian on WD MyCloud EX 4100 June 11, 2017 10:58PM |
Admin Registered: 13 years ago Posts: 18,994 |
Re: Debian on WD MyCloud EX 4100 June 12, 2017 03:48AM |
Registered: 7 years ago Posts: 183 |
Marvell>> setenv bootdev usb Marvell>> setenv device '0:1' Marvell>> setenv load_initr 0x2900000 Marvell>> setenv load_imag000000 Marvell>> setenv load_initading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' > setenv load_imageho loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' ** Bad device usb 0 ** Marvell>> setenv usb_set_b,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' > setenv usb_bootc'echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_initrd ; run usb_set_bootargs; bootm $load_image_addr $load_initrd_addr' > setenv bootcmd_usb start; run usb_set_bootargs; run usb_bootcmd; reset' > printenv<INTERRUPT> Marvell>> setenv load_initrd_addr 0x2900000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv usb_set_bsetenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' > setenv usb_bootc'cho Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_initrd ; run usb_set_bootargs; bootm $load_image_addr $load_initrd_addr' > setenv bootcmd_ub start; run usb_set_bootargs; run usb_bootcmd; reset'<INTERRUPT> Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' Marvell>> setenv usb_bootcmd 'echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_initrd ; run usb_set_bootargs; bootm $load_image_addr $load_initrd_addr' Marvell>> setenv bootcmd_usb 'usb start; run usb_set_bootargs; run usb_bootcmd; reset' Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_usb=usb start; run usb_set_bootargs; run usb_bootcmd; reset bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:0a:2d:22 eth1mtu=1500 eth2addr=00:50:43:0a:da:22 eth2mtu=1500 eth3addr=00:50:43:2d:da:0a eth3mtu=1500 ethact=egiga0 ethaddr=00:50:43:da:2d:22 ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=24 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=2.66.66.203 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000000 load_initading=uInitrd ... load_initr=0x2900000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:22:da:0a nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=2.66.66.32 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_bootcmd=echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_initrd ; run usb_set_bootargs; bootm $load_image_addr $load_initrd_addr usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3892/524284 bytes Marvell>> run bootcmd_usb (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3919325 bytes read in 324 ms (11.5 MiB/s) loading uInitrd ... 6210503 bytes read in 347 ms (17.1 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-06-04 8:57:41 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3919261 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: WD My Cloud EX4100 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @eefcd000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) earlyprintk=serial [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2060316K/2097152K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 36836K reserved, 0K cma-reserved, 1310720K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007882] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019057] Console: colour dummy device 80x30 [ 0.023570] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.033974] pid_max: default: 32768 minimum: 301 [ 0.038728] Security Framework initialized [ 0.042922] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.049595] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.057099] CPU: Testing write buffer coherency: ok [ 0.062169] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.067908] Setting up static identity map for 0x100000 - 0x100058 [ 0.074212] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4 [ 0.079471] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283913] Booting CPU 1 [ 0.286759] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286808] Brought up 2 CPUs [ 0.295567] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301886] CPU: All CPU(s) started in SVC mode. [ 0.307121] devtmpfs: initialized [ 0.312402] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320345] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330270] prandom: seed boundary self test passed [ 0.336895] prandom: 100 self tests passed [ 0.341055] pinctrl core: initialized pinctrl subsystem [ 0.346972] NET: Registered protocol family 16 [ 0.352014] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.393870] cpuidle: using governor ladder [ 0.423868] cpuidle: using governor menu [ 0.427933] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.436002] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.441983] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.450138] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.504817] vgaarb: loaded [ 0.507825] SCSI subsystem initialized [ 0.512054] usbcore: registered new interface driver usbfs [ 0.517687] usbcore: registered new interface driver hub [ 0.523110] usbcore: registered new device driver usb [ 0.528431] media: Linux media interface: v0.10 [ 0.533075] Linux video capture interface: v2.00 [ 0.538569] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.569975] VFS: Disk quotas dquot_6.6.0 [ 0.574002] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.587828] NET: Registered protocol family 2 [ 0.592648] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.599795] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.606346] TCP: Hash tables configured (established 8192 bind 8192) [ 0.612813] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.618826] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.625333] NET: Registered protocol family 1 [ 0.630018] RPC: Registered named UNIX socket transport module. [ 0.635994] RPC: Registered udp transport module. [ 0.640771] RPC: Registered tcp transport module. [ 0.645535] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.652160] Unpacking initramfs... [ 0.859678] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.865653] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.872434] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.881595] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.887802] audit: initializing netlink subsys (disabled) [ 0.893315] audit: type=2000 audit(0.880:1): initialized [ 0.899108] Initialise system trusted keyrings [ 0.903740] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.910319] zbud: loaded [ 0.913387] NFS: Registering the id_resolver key type [ 0.918504] Key type id_resolver registered [ 0.922767] Key type id_legacy registered [ 0.926846] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.933609] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.940156] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.947540] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.954156] orangefs_init: module version upstream loaded [ 0.961409] Key type asymmetric registered [ 0.965570] Asymmetric key parser 'x509' registered [ 0.970546] bounce: pool size: 64 pages [ 0.974516] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.981973] io scheduler noop registered [ 0.985960] io scheduler deadline registered [ 0.990314] io scheduler cfq registered (default) [ 0.995882] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.004310] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.011257] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.017579] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.024514] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.030437] PCI: bus0: Fast back to back transfers disabled [ 1.036073] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.044141] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.052305] PCI: bus1: Fast back to back transfers enabled [ 1.057963] PCI: bus2: Fast back to back transfers enabled [ 1.063556] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.068594] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.074036] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.138976] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.146583] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.208969] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.259665] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.267289] console [ttyS0] disabled [ 1.291014] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A [ 1.300056] console [ttyS0] enabled [ 1.300056] console [ttyS0] enabled [ 1.307143] bootconsole [earlycon0] disabled [ 1.307143] bootconsole [earlycon0] disabled [ 1.316715] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.325833] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.335398] scsi host0: ahci-mvebu [ 1.339104] scsi host1: ahci-mvebu [ 1.342708] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.350672] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.358767] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.367854] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.377225] scsi host2: ahci-mvebu [ 1.380870] scsi host3: ahci-mvebu [ 1.384424] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 43 [ 1.392389] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 43 [ 1.400817] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.408665] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc [ 1.415046] nand: Hynix H27U4G8F2DTR-BC [ 1.418911] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.426515] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.433709] Bad block table found at page 262080, version 0x01 [ 1.439901] Bad block table found at page 262016, version 0x01 [ 1.445930] nand_read_bbt: bad block at 0x00000dcc0000 [ 1.451099] nand_read_bbt: bad block at 0x00000fb00000 [ 1.456259] nand_read_bbt: bad block at 0x000012180000 [ 1.461426] nand_read_bbt: bad block at 0x0000139a0000 [ 1.466586] nand_read_bbt: bad block at 0x000017880000 [ 1.471753] nand_read_bbt: bad block at 0x0000178a0000 [ 1.476914] nand_read_bbt: bad block at 0x00001a640000 [ 1.482082] nand_read_bbt: bad block at 0x00001e9c0000 [ 1.487273] 3 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.493399] Creating 3 MTD partitions on "pxa3xx_nand-0": [ 1.498828] 0x000000000000-0x000000800000 : "U-Boot" [ 1.514495] 0x000000800000-0x000001000000 : "Linux" [ 1.530036] 0x000001000000-0x000040000000 : "Filesystem" [ 1.535371] mtd: partition "Filesystem" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x1f000000 [ 1.559252] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.565923] libphy: Fixed MDIO Bus: probed [ 1.570339] libphy: mdio_driver_register: mv88e6085 [ 1.575380] libphy: orion_mdio_bus: probed [ 1.585093] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 1.594133] mvneta f1070000.ethernet eth0: Using random mac address 06:c7:0e:e3:8a:6e [ 1.603534] mvneta f1030000.ethernet eth1: Using random mac address f2:f8:3a:a1:17:79 [ 1.611608] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.618175] ehci-pci: EHCI PCI platform driver [ 1.622687] ehci-orion: EHCI orion driver [ 1.626804] orion-ehci f1058000.usb: EHCI Host Controller [ 1.632251] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.639915] orion-ehci f1058000.usb: irq 38, io mem 0xf1058000 [ 1.668586] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.674636] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.681467] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.688727] usb usb1: Product: EHCI Host Controller [ 1.689919] ata1: SATA link down (SStatus 0 SControl 300) [ 1.699067] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 ehci_hcd [ 1.699867] ata2: SATA link down (SStatus 0 SControl 300) [ 1.710958] usb usb1: SerialNumber: f1058000.usb [ 1.715909] hub 1-0:1.0: USB hub found [ 1.719702] hub 1-0:1.0: 1 port detected [ 1.724075] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.729433] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.729824] ata3: SATA link down (SStatus 0 SControl 300) [ 1.739835] ata4: SATA link down (SStatus 0 SControl 300) [ 1.747858] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.756450] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000 [ 1.762310] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.769151] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.776404] usb usb2: Product: xHCI Host Controller [ 1.781311] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.787779] usb usb2: SerialNumber: f10f0000.usb3 [ 1.792797] hub 2-0:1.0: USB hub found [ 1.796581] hub 2-0:1.0: 1 port detected [ 1.800693] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.806033] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 1.813608] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.821801] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.828799] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.836052] usb usb3: Product: xHCI Host Controller [ 1.840960] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.847428] usb usb3: SerialNumber: f10f0000.usb3 [ 1.852431] hub 3-0:1.0: USB hub found [ 1.856211] hub 3-0:1.0: 1 port detected [ 1.860386] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.865729] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.873316] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.881915] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000 [ 1.887765] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.894592] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.901852] usb usb4: Product: xHCI Host Controller [ 1.906751] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.913263] usb usb4: SerialNumber: f10f8000.usb3 [ 1.918283] hub 4-0:1.0: USB hub found [ 1.922076] hub 4-0:1.0: 1 port detected [ 1.926174] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.931527] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 1.939089] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.947271] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.954097] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.961357] usb usb5: Product: xHCI Host Controller [ 1.966255] usb usb5: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.972773] usb usb5: SerialNumber: f10f8000.usb3 [ 1.977773] hub 5-0:1.0: USB hub found [ 1.981563] hub 5-0:1.0: 1 port detected [ 1.985748] usbcore: registered new interface driver usblp [ 1.991337] usbcore: registered new interface driver usb-storage [ 1.997541] mousedev: PS/2 mouse device common for all mice [ 2.003504] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 2.011182] i2c /dev entries driver [ 2.025985] orion_wdt: Initial timeout 171 sec [ 2.031636] marvell-cesa f1090000.crypto: CESA device successfully registered [ 2.038924] hidraw: raw HID events driver (C) Jiri Kosina [ 2.044529] usbcore: registered new interface driver usbhid [ 2.050137] usbhid: USB HID core driver [ 2.054103] drop_monitor: Initializing network drop monitor service [ 2.060442] Netfilter messages via NETLINK v0.30. [ 2.065173] ip_set: protocol 6 [ 2.068408] NET: Registered protocol family 10 [ 2.073440] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.080162] NET: Registered protocol family 17 [ 2.084739] 8021q: 802.1Q VLAN Support v1.8 [ 2.089146] Key type dns_resolver registered [ 2.093518] ThumbEE CPU extension supported. [ 2.097811] Registering SWP/SWPB emulation handler [ 2.102969] registered taskstats version 1 [ 2.107084] Loading compiled-in X.509 certificates [ 2.111936] zswap: loaded using pool lzo/zbud [ 2.158603] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 2.165296] Key type big_key registered [ 2.172605] Key type encrypted registered [ 2.177570] armada38x-rtc f10a3800.rtc: setting system clock to 2017-06-12 08:25:09 UTC (1497255909) [ 2.187767] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.226333] systemd-udevd[1323]: starting version 215 [ 2.232314] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.338798] usb 2-1: New USB device found, idVendor=045b, idProduct=0209 [ 2.345541] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.359945] hub 2-1:1.0: USB hub found [ 2.366640] hub 2-1:1.0: 4 ports detected [ 2.479071] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.510108] usb 3-1: New USB device found, idVendor=045b, idProduct=0210 [ 2.516840] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.524587] hub 3-1:1.0: USB hub found [ 2.528606] hub 3-1:1.0: 4 ports detected [ 2.688591] usb 2-1.3: new high-speed USB device number 3 using xhci-hcd [ 2.819209] usb 2-1.3: New USB device found, idVendor=0781, idProduct=5571 [ 2.826115] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.833467] usb 2-1.3: Product: Cruzer Fit [ 2.837580] usb 2-1.3: Manufacturer: SanDisk [ 2.841874] usb 2-1.3: SerialNumber: 4C530302071223122304 [ 2.848117] usb-storage 2-1.3:1.0: USB Mass Storage device detected [ 2.854568] scsi host4: usb-storage 2-1.3:1.0 [ 2.860512] usbcore: registered new interface driver uas [ 3.929111] scsi 4:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6 [ 3.939413] sd 4:0:0:0: Attached scsi generic sg0 type 0 [ 3.944863] sd 4:0:0:0: [sda] 61489152 512-byte logical blocks: (31.5 GB/29.3 GiB) [ 3.953959] sd 4:0:0:0: [sda] Write Protect is off [ 3.959092] sd 4:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.971219] sda: sda1 [ 3.979391] sd 4:0:0:0: [sda] Attached SCSI removable disk [ 3.994170] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.643619] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.652687] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 17.659605] EXT4-fs (sda1): write access will be enabled during recovery [ 18.430937] EXT4-fs (sda1): recovery complete [ 18.437855] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 19.154219] systemd-udevd[1530]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 20.057122] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 34132/1925120 files, 299594/7685888 blocks done. [ 20.171740] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 21.198981] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/06:c7:0e:e3:8a:6e Sending on LPF/eth0/06:c7:0e:e3:8a:6e Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.[ 82.452690] random: crng init done 255.255 port 67 interval 10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2475 (syslogd) . ok [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting NTP server: ntpd. [ ok ] Starting system message bus: dbus. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2476 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login: root Password: Last login: Sun Jun 11 13:39:53 PDT 2017 on ttyS0 Linux debian 4.9.0-mvebu-tld-12 #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian WD My Cloud EX4100 Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 01:36:51 up 11 min, 1 user, load average: 0.00, 0.00, 0.00 root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00800000 00020000 "U-Boot" mtd1: 00800000 00020000 "Linux" mtd2: 1f000000 00020000 "Filesystem"
Re: Debian on WD MyCloud EX 4100 June 12, 2017 01:38PM |
Admin Registered: 13 years ago Posts: 18,994 |
Re: Debian on WD MyCloud EX 4100 June 16, 2017 04:28AM |
Registered: 7 years ago Posts: 183 |
dev: size erasesize name mtd0: 00500000 00020000 "U-Boot" mtd1: 00a00000 00020000 "uImage" mtd2: 00f00000 00020000 "uRamdisk" mtd3: 1c800000 00020000 "image.cfs" mtd4: 03800000 00020000 "rescue_fw" mtd5: 02900000 00020000 "config" mtd6: 01500000 00020000 "reserve1" mtd7: 00b00000 00020000 "reserve2"
Warning: Bad CRC, using default environment bootargs= bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=3 baudrate=115200 stdin=serial,cros-ec-keyb stdout=serial,lcd stderr=serial,lcd
Cannot read bad block mark: Invalid argument
setenv bootdev usb setenv device '0:1' setenv load_initrd_addr 0x2900000 setenv load_image_addr 0x02000000 setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 earlyprintk=serial' setenv mtdparts 'mtdparts=armada-nand-0:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2)' setenv usb_bootcmd 'echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_initrd ; run usb_set_bootargs; bootm $load_image_addr $load_initrd_addr' setenv bootcmd_usb 'usb start; run usb_set_bootargs; run usb_bootcmd; reset' printenv run bootcmd_usb
sudo ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-boot-a38x-Ylowstone_2014T30p6_bodhi-tld-1-nand-uart.bin -s 0 -q 1 Sending boot message. Please reboot the target...|▒"▒&T▒▒▒"3DUfw▒"3DUfw▒"3DUf/▒"3DUfw▒"3DUfw Sending boot image... 0 % [......................................................................] 0 % [......................................................................] 1 % [......................................................................] 2 % [......................................................................] 3 % [......................................................................] 4 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 7 % [......................................................................] 8 % [......................................................................] 9 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 12 % [......................................................................] 13 % [......................................................................] 14 % [......................................................................] 15 % [......................................................................] 15 % [......................................................................] 16 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 19 % [......................................................................] 20 % [......................................................................] 21 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 24 % [......................................................................] 25 % [......................................................................] 26 % [......................................................................] 27 % [......................................................................] 28 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 30 % [......................................................................] 31 % [......................................................................] 32 % [......................................................................] 33 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 36 % [......................................................................] 37 % [......................................................................] 38 % [......................................................................] 39 % [......................................................................] 40 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 43 % [......................................................................] 44 % [......................................................................] 45 % [......................................................................] 45 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 48 % [......................................................................] 49 % [......................................................................] 50 % [......................................................................] 51 % [......................................................................] 52 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 55 % [......................................................................] 56 % [......................................................................] 57 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 60 % [......................................................................] 60 % [......................................................................] 61 % [......................................................................] 62 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 65 % [......................................................................] 66 % [......................................................................] 67 % [......................................................................] 68 % [......................................................................] 69 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 72 % [......................................................................] 73 % [......................................................................] 74 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 76 % [......................................................................] 77 % [......................................................................] 78 % [......................................................................] 79 % [......................................................................] 80 % [......................................................................] 81 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 84 % [......................................................................] 85 % [......................................................................] 86 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 89 % [......................................................................] 90 % [......................................................................] 91 % [......................................................................] 91 % [......................................................................] 92 % [......................................................................] 93 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 96 % [......................................................................] 97 % [......................................................................] 98 % [......................................................................] 99 % [.........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.06 (Jun 08 2017 - 21:25:53) Marvell version: 2014_T3.0p6 - bodhi-tld-1 mvBoardSatRRead: Error: Read from S@R failed mvBoardSatRRead: Error: Read from S@R failed mvBoardSatRRead: Error: Read from S@R failed Board: DB-88F6820-BP SoC: MV88F6828 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1600 [MHz] L2 @ 800 [MHz] TClock @ 200 [MHz] DDR @ 800 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 2 GiB Map: Code: 0x7fece000:0x7ff95d14 BSS: 0x7ffef254 Stack: 0x7f9cdf20 Heap: 0x7f9ce000:0x7fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: dcad ,512 MiB MMC: mv_sdh: 0 USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00001f500000-0x00001ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 36 (0x00000024)... Done lan mac_addr : 00 90 a9 e5 19 1e Set lan 0 WakeOnLan ok Set lan 1 WakeOnLan ok MicroP Enable HD Enable HD1 Enable HD2 Enable HD3 Enable HD4 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | SGMII | 0x01 | egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Marvell>> setenv bootdev usb Marvell>> setenv device '0:1' Marvell>> setenv load_initrd_addr 0x2900000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 earlyprintk=serial' Marvell>> setenv mtdparts 'mtdparts=armada-nand-0:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2)' Marvell>> setenv usb_bootcmd 'echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_initrd ; run usb_set_bootargs; bootm $load_image_addr $load_initrd_addr' Marvell>> setenv bootcmd_usb 'usb start; run usb_set_bootargs; run usb_bootcmd; reset' Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_usb=usb start; run usb_set_bootargs; run usb_bootcmd; reset bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:e0:2c:2d eth1mtu=1500 eth2addr=00:50:43:e0:32:2d eth2mtu=1500 eth3addr=00:50:43:2c:32:e0 eth3mtu=1500 ethact=egiga0 ethaddr=00:50:43:32:2c:2d ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=24 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=2.66.66.203 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand-0:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:2d:32:e0 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=2.66.66.32 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_bootcmd=echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_initrd ; run usb_set_bootargs; bootm $load_image_addr $load_initrd_addr usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 earlyprintk=serial vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3831/524284 bytes Marvell>> run bootcmd_usb (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3919689 bytes read in 282 ms (13.3 MiB/s) loading uInitrd ... 6210503 bytes read in 368 ms (16.1 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-06-12 5:14:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3919625 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: WD My Cloud EX4100 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @eefcd000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 earlyprintk=serial [ 0.000000] [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2060316K/2097152K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 36836K reserved, 0K cma-reserved, 1310720K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007882] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019061] Console: colour dummy device 80x30 [ 0.023575] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.033979] pid_max: default: 32768 minimum: 301 [ 0.038731] Security Framework initialized [ 0.042925] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.049599] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.057103] CPU: Testing write buffer coherency: ok [ 0.062173] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.067910] Setting up static identity map for 0x100000 - 0x100058 [ 0.074215] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4 [ 0.079474] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283911] Booting CPU 1 [ 0.286758] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286806] Brought up 2 CPUs [ 0.295564] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301884] CPU: All CPU(s) started in SVC mode. [ 0.307116] devtmpfs: initialized [ 0.312412] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320359] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330285] prandom: seed boundary self test passed [ 0.336909] prandom: 100 self tests passed [ 0.341069] pinctrl core: initialized pinctrl subsystem [ 0.346988] NET: Registered protocol family 16 [ 0.352014] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.393867] cpuidle: using governor ladder [ 0.423865] cpuidle: using governor menu [ 0.427918] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.435986] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.441966] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.450121] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.504827] vgaarb: loaded [ 0.507837] SCSI subsystem initialized [ 0.512058] usbcore: registered new interface driver usbfs [ 0.517691] usbcore: registered new interface driver hub [ 0.523125] usbcore: registered new device driver usb [ 0.528450] media: Linux media interface: v0.10 [ 0.533087] Linux video capture interface: v2.00 [ 0.538574] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.569957] VFS: Disk quotas dquot_6.6.0 [ 0.573984] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.587855] NET: Registered protocol family 2 [ 0.592671] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.599819] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.606369] TCP: Hash tables configured (established 8192 bind 8192) [ 0.612838] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.618848] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.625354] NET: Registered protocol family 1 [ 0.630039] RPC: Registered named UNIX socket transport module. [ 0.636015] RPC: Registered udp transport module. [ 0.640795] RPC: Registered tcp transport module. [ 0.645560] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.652184] Unpacking initramfs... [ 0.859064] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.865024] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.871808] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.880957] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.887162] audit: initializing netlink subsys (disabled) [ 0.892674] audit: type=2000 audit(0.880:1): initialized [ 0.898440] Initialise system trusted keyrings [ 0.903098] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.909675] zbud: loaded [ 0.912740] NFS: Registering the id_resolver key type [ 0.917858] Key type id_resolver registered [ 0.922120] Key type id_legacy registered [ 0.926200] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.932962] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.939509] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.946896] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.953501] orangefs_init: module version upstream loaded [ 0.960787] Key type asymmetric registered [ 0.964949] Asymmetric key parser 'x509' registered [ 0.969925] bounce: pool size: 64 pages [ 0.973898] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.981352] io scheduler noop registered [ 0.985340] io scheduler deadline registered [ 0.989693] io scheduler cfq registered (default) [ 0.995257] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.003688] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.010634] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.016956] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.023890] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.029823] PCI: bus0: Fast back to back transfers disabled [ 1.035459] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.043527] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.051691] PCI: bus1: Fast back to back transfers enabled [ 1.057342] PCI: bus2: Fast back to back transfers enabled [ 1.062933] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.067961] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.073408] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.138980] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.146580] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.208975] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.258980] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.266640] console [ttyS0] disabled [ 1.290385] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A [ 1.299440] console [ttyS0] enabled [ 1.299440] console [ttyS0] enabled [ 1.306528] bootconsole [earlycon0] disabled [ 1.306528] bootconsole [earlycon0] disabled [ 1.316108] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.325214] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.334760] scsi host0: ahci-mvebu [ 1.338441] scsi host1: ahci-mvebu [ 1.342075] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.350038] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.358118] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.367217] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.376591] scsi host2: ahci-mvebu [ 1.380237] scsi host3: ahci-mvebu [ 1.383789] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 43 [ 1.391754] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 43 [ 1.400175] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.408024] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc [ 1.414418] nand: Hynix H27U4G8F2DTR-BC [ 1.418270] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.425881] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.433072] Bad block table found at page 262080, version 0x01 [ 1.439262] Bad block table found at page 262016, version 0x01 [ 1.445292] nand_read_bbt: bad block at 0x00000dcc0000 [ 1.450462] nand_read_bbt: bad block at 0x00000fb00000 [ 1.455622] nand_read_bbt: bad block at 0x000012180000 [ 1.460787] nand_read_bbt: bad block at 0x0000139a0000 [ 1.465948] nand_read_bbt: bad block at 0x000017880000 [ 1.471115] nand_read_bbt: bad block at 0x0000178a0000 [ 1.476276] nand_read_bbt: bad block at 0x00001a640000 [ 1.481442] nand_read_bbt: bad block at 0x00001e9c0000 [ 1.486639] 8 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.492767] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 1.498189] 0x000000000000-0x000000500000 : "U-Boot" [ 1.513855] 0x000000500000-0x000000f00000 : "uImage" [ 1.519475] 0x000000a00000-0x000001900000 : "uRamdisk" [ 1.535267] 0x000000f00000-0x00001d700000 : "image.cfs" [ 1.552756] 0x00001c800000-0x000039f00000 : "rescue_fw" [ 1.558004] mtd: partition "rescue_fw" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x3800000 [ 1.579543] 0x00001d700000-0x00003c200000 : "config" [ 1.584530] mtd: partition "config" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x2900000 [ 1.605758] 0x00001eb00000-0x00003e000000 : "reserve1" [ 1.610932] mtd: partition "reserve1" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x1500000 [ 1.622262] 0x00001f500000-0x00003f400000 : "reserve2" [ 1.627423] mtd: partition "reserve2" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0xb00000 [ 1.639233] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.645891] libphy: Fixed MDIO Bus: probed [ 1.650293] libphy: mdio_driver_register: mv88e6085 [ 1.655323] libphy: orion_mdio_bus: probed [ 1.665040] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 1.674074] mvneta f1070000.ethernet eth0: Using random mac address e2:72:92:83:d3:29 [ 1.683481] mvneta f1030000.ethernet eth1: Using random mac address f6:b2:55:63:6d:07 [ 1.689844] ata1: SATA link down (SStatus 0 SControl 300) [ 1.697061] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.699983] ata2: SATA link down (SStatus 0 SControl 300) [ 1.709067] ehci-pci: EHCI PCI platform driver [ 1.713571] ehci-orion: EHCI orion driver [ 1.717695] orion-ehci f1058000.usb: EHCI Host Controller [ 1.723142] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.729849] ata3: SATA link down (SStatus 0 SControl 300) [ 1.736222] orion-ehci f1058000.usb: irq 38, io mem 0xf1058000 [ 1.739904] ata4: SATA link down (SStatus 0 SControl 300) [ 1.768590] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.774640] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.781471] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.788731] usb usb1: Product: EHCI Host Controller [ 1.793629] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 ehci_hcd [ 1.800103] usb usb1: SerialNumber: f1058000.usb [ 1.805073] hub 1-0:1.0: USB hub found [ 1.808865] hub 1-0:1.0: 1 port detected [ 1.813250] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.818609] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.826196] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.834787] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000 [ 1.840646] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.847464] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.854739] usb usb2: Product: xHCI Host Controller [ 1.859646] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.866114] usb usb2: SerialNumber: f10f0000.usb3 [ 1.871139] hub 2-0:1.0: USB hub found [ 1.874919] hub 2-0:1.0: 1 port detected [ 1.879025] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.884365] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 1.891938] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.900135] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.906953] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.914213] usb usb3: Product: xHCI Host Controller [ 1.919175] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.925643] usb usb3: SerialNumber: f10f0000.usb3 [ 1.930649] hub 3-0:1.0: USB hub found [ 1.934430] hub 3-0:1.0: 1 port detected [ 1.938598] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.943942] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.951524] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.960122] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000 [ 1.965969] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.972796] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.980056] usb usb4: Product: xHCI Host Controller [ 1.984953] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.991464] usb usb4: SerialNumber: f10f8000.usb3 [ 1.996465] hub 4-0:1.0: USB hub found [ 2.000257] hub 4-0:1.0: 1 port detected [ 2.004356] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 2.009706] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 2.017262] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.025451] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 2.032279] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.039585] usb usb5: Product: xHCI Host Controller [ 2.044482] usb usb5: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 2.050958] usb usb5: SerialNumber: f10f8000.usb3 [ 2.055945] hub 5-0:1.0: USB hub found [ 2.059739] hub 5-0:1.0: 1 port detected [ 2.063926] usbcore: registered new interface driver usblp [ 2.069514] usbcore: registered new interface driver usb-storage [ 2.075714] mousedev: PS/2 mouse device common for all mice [ 2.081672] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 2.089396] i2c /dev entries driver [ 2.104196] orion_wdt: Initial timeout 171 sec [ 2.109883] marvell-cesa f1090000.crypto: CESA device successfully registered [ 2.117154] hidraw: raw HID events driver (C) Jiri Kosina [ 2.122781] usbcore: registered new interface driver usbhid [ 2.128377] usbhid: USB HID core driver [ 2.132357] drop_monitor: Initializing network drop monitor service [ 2.138692] Netfilter messages via NETLINK v0.30. [ 2.143426] ip_set: protocol 6 [ 2.146660] NET: Registered protocol family 10 [ 2.151843] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.158512] NET: Registered protocol family 17 [ 2.163116] 8021q: 802.1Q VLAN Support v1.8 [ 2.167337] Key type dns_resolver registered [ 2.171813] ThumbEE CPU extension supported. [ 2.176106] Registering SWP/SWPB emulation handler [ 2.181270] registered taskstats version 1 [ 2.185385] Loading compiled-in X.509 certificates [ 2.190238] zswap: loaded using pool lzo/zbud [ 2.236593] Key type big_key registered [ 2.240480] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 2.250477] Key type encrypted registered [ 2.255439] armada38x-rtc f10a3800.rtc: setting system clock to 2017-06-16 09:00:59 UTC (1497603659) [ 2.265625] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.304034] systemd-udevd[1348]: starting version 215 [ 2.310126] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.408931] usb 2-1: New USB device found, idVendor=045b, idProduct=0209 [ 2.415676] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.426174] hub 2-1:1.0: USB hub found [ 2.431933] hub 2-1:1.0: 4 ports detected [ 2.548854] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.580175] usb 3-1: New USB device found, idVendor=045b, idProduct=0210 [ 2.586907] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.594659] hub 3-1:1.0: USB hub found [ 2.598673] hub 3-1:1.0: 4 ports detected [ 2.758594] usb 2-1.3: new high-speed USB device number 3 using xhci-hcd [ 2.889219] usb 2-1.3: New USB device found, idVendor=0781, idProduct=5571 [ 2.896125] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.903477] usb 2-1.3: Product: Cruzer Fit [ 2.907591] usb 2-1.3: Manufacturer: SanDisk [ 2.911885] usb 2-1.3: SerialNumber: 4C530302071223122304 [ 2.918128] usb-storage 2-1.3:1.0: USB Mass Storage device detected [ 2.924575] scsi host4: usb-storage 2-1.3:1.0 [ 2.930494] usbcore: registered new interface driver uas [ 4.009112] scsi 4:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6 [ 4.019456] sd 4:0:0:0: Attached scsi generic sg0 type 0 [ 4.025527] sd 4:0:0:0: [sda] 61489152 512-byte logical blocks: (31.5 GB/29.3 GiB) [ 4.034021] sd 4:0:0:0: [sda] Write Protect is off [ 4.039143] sd 4:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 4.051358] sda: sda1 [ 4.055265] sd 4:0:0:0: [sda] Attached SCSI removable disk [ 4.069405] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.713617] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.729582] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 18.499917] systemd-udevd[1555]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 19.136288] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 34187/1925120 files, 319002/7685888 blocks done. [ 19.255810] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 20.308982] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/e2:72:92:83:d3:29 Sending on LPF/eth0/e2:72:92:83:d3:29 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 17 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runl[ 81.752872] random: crng init done evel 2. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2503 (syslogd) . ok [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2502 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login: root Password: Last login: Fri Jun 16 01:09:52 PDT 2017 on ttyS0 Linux debian 4.9.0-mvebu-tld-12 #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian WD My Cloud EX4100 Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 02:02:46 up 1 min, 1 user, load average: 0.00, 0.00, 0.00 root@debian:~#
Re: Debian on WD MyCloud EX 4100 June 16, 2017 02:59PM |
Admin Registered: 13 years ago Posts: 18,994 |
> dev: size erasesize name > mtd0: 00500000 00020000 "U-Boot" > mtd1: 00a00000 00020000 "uImage" > mtd2: 00f00000 00020000 "uRamdisk" > mtd3: 1c800000 00020000 "image.cfs" > mtd4: 03800000 00020000 "rescue_fw" > mtd5: 02900000 00020000 "config" > mtd6: 01500000 00020000 "reserve1" > mtd7: 00b00000 00020000 "reserve2" >
> sudo ./kwboot -f -t -B 115200 /dev/ttyAMA0 -b u-bo > ot-a38x-Ylowstone_2014T30p6_bodhi-tld-1-nand-uart. > bin -s 0 -q 1 > Sending boot message. Please reboot the target...| > U-Boot 2013.01_v1.06 (Jun 08 2017 - 21:25:53) Marv > ell version: 2014_T3.0p6 - bodhi-tld-1
> /dev/mtd0 0x100000 0x80000 0x20000 in /etc/fw_env. > config gives me > > Warning: Bad CRC, using default environment > bootargs= > bootcmd=bootp; setenv bootargs root=/dev/nfs nfsro > ot=${serverip}:${rootpath} ip=${ipaddr}:${serverip > }:${gatewayip}:${netmask}:${hostname}::off; bootm > bootdelay=3 > baudrate=115200 > stdin=serial,cros-ec-keyb > stdout=serial,lcd > stderr=serial,lcd > > /dev/mtd0 0x500000 0x80000 0x20000 in /etc/fw_env > .config gives me > Cannot read bad block mark: Invalid argument >
Re: Debian on WD MyCloud EX 4100 June 16, 2017 09:30PM |
Admin Registered: 13 years ago Posts: 18,994 |
cd /tmp wget http://forum.doozan.com/file.php?2,file=1374,filename=find_uboot_env_location.sh chmod +x find_uboot_env_location.sh ./find_uboot_env_location.sh
Re: Debian on WD MyCloud EX 4100 June 18, 2017 12:34PM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 18, 2017 03:26PM |
Registered: 7 years ago Posts: 119 |
Re: Debian on WD MyCloud EX 4100 June 18, 2017 04:21PM |
Admin Registered: 13 years ago Posts: 18,994 |
grep -i bootcmd mtd0 grep -i bootcmd mtd1
Re: Debian on WD MyCloud EX 4100 June 18, 2017 04:45PM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 18, 2017 04:57PM |
Admin Registered: 13 years ago Posts: 18,994 |
Re: Debian on WD MyCloud EX 4100 June 19, 2017 02:02PM |
Registered: 7 years ago Posts: 119 |
Re: Debian on WD MyCloud EX 4100 June 19, 2017 02:13PM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 19, 2017 02:16PM |
Registered: 7 years ago Posts: 119 |
Re: Debian on WD MyCloud EX 4100 June 19, 2017 06:39PM |
Admin Registered: 13 years ago Posts: 18,994 |
Re: Debian on WD MyCloud EX 4100 June 20, 2017 12:50AM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 20, 2017 03:20AM |
Admin Registered: 13 years ago Posts: 18,994 |
003e42e0 30 2c 31 31 35 32 30 30 20 65 61 72 6c 79 70 72 |0,115200 earlypr| 003e42f0 69 6e 74 6b 00 00 00 00 00 00 00 02 00 00 00 01 |intk............| 003e4300 61 6c 69 61 73 65 73 00 00 00 00 03 00 00 00 1e |aliases.........| 003e4310 00 00 00 35 2f 73 6f 63 2f 69 6e 74 65 72 6e 61 |...5/soc/interna| 003e4320 6c 2d 72 65 67 73 2f 67 70 69 6f 40 31 38 31 30 |l-regs/gpio@1810| 003e4330 30 00 00 00 00 00 00 03 00 00 00 1e 00 00 00 3b |0..............;|
/dev/mtd0 0xa0000 /dev/mtd0 0xc0000
cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000or
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xa0000 0x20000 0x20000
Re: Debian on WD MyCloud EX 4100 June 20, 2017 03:41AM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 20, 2017 03:57AM |
Admin Registered: 13 years ago Posts: 18,994 |
Re: Debian on WD MyCloud EX 4100 June 20, 2017 04:19AM |
Registered: 7 years ago Posts: 183 |
root@debian:/media/ex4100nandbackup# cd no_oob_ecc root@debian:/media/ex4100nandbackup/no_oob_ecc# nanddump --noecc --omitoob -f mtd0 /dev/mtd0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00500000... root@debian:/media/ex4100nandbackup/no_oob_ecc# nanddump --noecc --omitoob -f mtd1 /dev/mtd1 /dev/mtd7Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00a00000... root@debian:/media/ex4100nandbackup/no_oob_ecc# nanddump --noecc --omitoob -f mtd2 /dev/mtd2 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00f00000... root@debian:/media/ex4100nandbackup/no_oob_ecc# nanddump --noecc --omitoob -f mtd3 /dev/mtd3 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x1c800000... root@debian:/media/ex4100nandbackup/no_oob_ecc# nanddump --noecc --omitoob -f mtd4 /dev/mtd4 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x03800000... root@debian:/media/ex4100nandbackup/no_oob_ecc# nanddump --noecc --omitoob -f mtd5 /dev/mtd5 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x02900000... root@debian:/media/ex4100nandbackup/no_oob_ecc# nanddump --noecc --omitoob -f mtd6 /dev/mtd6 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x01500000... root@debian:/media/ex4100nandbackup/no_oob_ecc# nanddump --noecc --omitoob -f mtd7 /dev/mtd7 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00b00000... root@debian:/media/ex4100nandbackup/no_oob_ecc# dir mtd0 mtd1 mtd2 mtd3 mtd4 mtd5 mtd6 mtd7 root@debian:/media/ex4100nandbackup/no_oob_ecc# cd .. root@debian:/media/ex4100nandbackup# dir no_oob_ecc oob_ecc root@debian:/media/ex4100nandbackup# cd oob_ecc root@debian:/media/ex4100nandbackup/oob_ecc# nanddump -f mtd0 /dev/mtd0 ECC failed: 0 ECC corrected: 0 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00500000... root@debian:/media/ex4100nandbackup/oob_ecc# nanddump -f mtd1 /dev/mtd1 ECC failed: 0 ECC corrected: 0 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00a00000... root@debian:/media/ex4100nandbackup/oob_ecc# nanddump -f mtd2 /dev/mtd2 ECC failed: 0 ECC corrected: 0 Number of bad blocks: 0 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00f00000... root@debian:/media/ex4100nandbackup/oob_ecc# nanddump -f mtd3 /dev/mtd3 ECC failed: 0 ECC corrected: 0 Number of bad blocks: 7 Number of bbt blocks: 0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x1c800000... root@debian:/media/ex4100nandbackup/oob_ecc# nanddump -f mtd4 /dev/mtd4 ECC failed: 0 ECC corrected: 0 Number of bad blocks: 1 Number of bbt blocks: 8 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x03800000... root@debian:/media/ex4100nandbackup/oob_ecc# nanddump -f mtd5 /dev/mtd5 ECC failed: 0 ECC corrected: 0 Number of bad blocks: 1 Number of bbt blocks: 8 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x02900000... root@debian:/media/ex4100nandbackup/oob_ecc# nanddump -f mtd6 /dev/mtd6 ECC failed: 0 ECC corrected: 0 Number of bad blocks: 0 Number of bbt blocks: 8 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x01500000... root@debian:/media/ex4100nandbackup/oob_ecc# nanddump -f mtd7 /dev/mtd7 ECC failed: 0 ECC corrected: 0 Number of bad blocks: 0 Number of bbt blocks: 8 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00b00000... root@debian:/media/ex4100nandbackup/oob_ecc#
Re: Debian on WD MyCloud EX 4100 June 20, 2017 04:38AM |
Admin Registered: 13 years ago Posts: 18,994 |
Re: Debian on WD MyCloud EX 4100 June 20, 2017 05:19AM |
Registered: 7 years ago Posts: 183 |
Re: Debian on WD MyCloud EX 4100 June 20, 2017 12:54PM |
Registered: 7 years ago Posts: 119 |
$ kwboot -f -t -B 115200 /dev/ttyUSB0 -b /tmp/u-boot-a38x-Yosemite_2014T3_PQ-nand-uart.bin -s 0 -q 1 (waiting) Marvell>> printenv ... serverip=192.168.11.114 ... Environment size: 3209/524284 bytes Marvell>> setenv serverip 192.168.11.110 Marvell>> saveenv Saving Environment to NAND... Erasing Nand... Writing to Nand... done Marvell>> reset resetting ... Marvell>> printenv ... serverip=192.168.11.110 ... Environment size: 3209/524284 bytes Marvell>>
Re: Debian on WD MyCloud EX 4100 June 20, 2017 01:08PM |
Registered: 7 years ago Posts: 183 |
Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 10:11:24 up 18 min, 1 user, load average: 0.00, 0.00, 0.00 root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00500000 00020000 "U-Boot" mtd1: 00a00000 00020000 "uImage" mtd2: 00f00000 00020000 "uRamdisk" mtd3: 1c800000 00020000 "image.cfs" mtd4: 03800000 00020000 "rescue_fw" mtd5: 02900000 00020000 "config" mtd6: 01500000 00020000 "reserve1" mtd7: 00b00000 00020000 "reserve2" root@debian:~# cd /media/ex4100nandbackup/no_oob_ecc root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd0 | grep -A 5 -i bootcmd 000b82f0 65 6e 74 20 62 6f 6f 74 63 6d 64 3a 20 25 73 0a |ent bootcmd: %s.| 000b8300 00 0a 50 65 72 6d 61 6e 65 6e 74 20 63 6f 6e 73 |..Permanent cons| 000b8310 6f 6c 65 3a 20 25 73 0a 00 69 70 61 64 64 72 00 |ole: %s..ipaddr.| 000b8320 73 65 72 76 65 72 69 70 00 62 6f 6f 74 61 72 67 |serverip.bootarg| 000b8330 73 5f 65 6e 64 00 65 74 68 31 61 64 64 72 00 73 |s_end.eth1addr.s| 000b8340 65 74 65 6e 76 20 62 6f 6f 74 61 72 67 73 20 24 |etenv bootargs $| -- 000b9900 20 62 6f 6f 74 63 6d 64 20 24 62 6f 6f 74 63 6d | bootcmd $bootcm| 000b9910 64 5f 66 64 74 5f 62 6f 6f 74 00 62 6f 6f 74 63 |d_fdt_boot.bootc| 000b9920 6d 64 5f 66 64 74 00 74 66 74 70 62 6f 6f 74 20 |md_fdt.tftpboot | 000b9930 30 78 32 30 30 30 30 30 30 20 24 69 6d 61 67 65 |0x2000000 $image| 000b9940 5f 6e 61 6d 65 3b 74 66 74 70 62 6f 6f 74 20 24 |_name;tftpboot $| 000b9950 66 64 74 61 64 64 72 20 24 66 64 74 66 69 6c 65 |fdtaddr $fdtfile| -- 000bdaa0 2c 20 72 75 6e 20 27 62 6f 6f 74 63 6d 64 27 00 |, run 'bootcmd'.| 000bdab0 62 6f 6f 74 6d 00 62 6f 6f 74 20 61 70 70 6c 69 |bootm.boot appli| 000bdac0 63 61 74 69 6f 6e 20 69 6d 61 67 65 20 66 72 6f |cation image fro| 000bdad0 6d 20 6d 65 6d 6f 72 79 00 6c 6f 61 64 6f 73 00 |m memory.loados.| 000bdae0 72 61 6d 64 69 73 6b 00 63 6d 64 6c 69 6e 65 00 |ramdisk.cmdline.| 000bdaf0 62 64 74 00 70 72 65 70 00 4c 69 73 74 20 6f 66 |bdt.prep.List of| -- 000cd190 62 6f 6f 74 63 6d 64 5f 6c 67 63 79 00 74 66 74 |bootcmd_lgcy.tft| 000cd1a0 70 62 6f 6f 74 20 30 78 32 30 30 30 30 30 30 20 |pboot 0x2000000 | 000cd1b0 24 69 6d 61 67 65 5f 6e 61 6d 65 3b 20 73 65 74 |$image_name; set| 000cd1c0 65 6e 76 20 62 6f 6f 74 61 72 67 73 20 24 62 6f |env bootargs $bo| 000cd1d0 6f 74 61 72 67 73 5f 64 66 6c 74 3b 20 62 6f 6f |otargs_dflt; boo| 000cd1e0 74 6d 20 30 78 32 30 30 30 30 30 30 3b 20 00 3a |tm 0x2000000; .:| -- 000cd450 5f 62 6f 6f 74 63 6d 64 00 72 75 6e 20 6e 65 74 |_bootcmd.run net| 000cd460 62 73 64 5f 67 65 74 20 3b 20 72 75 6e 20 6e 65 |bsd_get ; run ne| 000cd470 74 62 73 64 5f 73 65 74 5f 61 72 67 73 20 3b 20 |tbsd_set_args ; | 000cd480 72 75 6e 20 6e 65 74 62 73 64 5f 62 6f 6f 74 00 |run netbsd_boot.| 000cd490 76 78 77 6f 72 6b 73 5f 65 6e 00 6d 67 69 28 30 |vxworks_en.mgi(0| 000cd4a0 2c 30 29 20 68 6f 73 74 3a 76 78 57 6f 72 6b 73 |,0) host:vxWorks| root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd1 | grep -A 5 -i bootcmd root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd2 | grep -A 5 -i bootcmd root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd3 | grep -A 5 -i bootcmd root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd4 | grep -A 5 -i bootcmd root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd5 | grep -A 5 -i bootcmd root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd6 | grep -A 5 -i bootcmd root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd7 | grep -A 5 -i bootcmd root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd0 | grep -A 5 -i 115200 000b0570 74 79 53 30 2c 31 31 35 32 30 30 00 62 6f 6f 74 |tyS0,115200.boot| 000b0580 64 65 6c 61 79 3d 31 00 62 61 75 64 72 61 74 65 |delay=1.baudrate| 000b0590 3d 31 31 35 32 30 30 00 6c 6f 61 64 73 5f 65 63 |=115200.loads_ec| 000b05a0 68 6f 3d 30 00 69 70 61 64 64 72 3d 32 2e 36 36 |ho=0.ipaddr=2.66| 000b05b0 2e 36 36 2e 32 30 33 00 73 65 72 76 65 72 69 70 |.66.203.serverip| 000b05c0 3d 32 2e 36 36 2e 36 36 2e 33 32 00 72 6f 6f 74 |=2.66.66.32.root| 000b05d0 70 61 74 68 3d 2f 73 72 76 2f 6e 66 73 2f 00 6e |path=/srv/nfs/.n| 000b05e0 65 74 6d 61 73 6b 3d 32 35 35 2e 32 35 35 2e 32 |etmask=255.255.2| -- 000b0630 61 75 64 72 61 74 65 3d 31 31 35 32 30 30 00 6c |audrate=115200.l| 000b0640 6f 61 64 73 5f 65 63 68 6f 3d 30 00 69 70 61 64 |oads_echo=0.ipad| 000b0650 64 72 3d 32 2e 36 36 2e 36 36 2e 32 30 33 00 73 |dr=2.66.66.203.s| 000b0660 65 72 76 65 72 69 70 3d 32 2e 36 36 2e 36 36 2e |erverip=2.66.66.| 000b0670 33 32 00 72 6f 6f 74 70 61 74 68 3d 2f 73 72 76 |32.rootpath=/srv| 000b0680 2f 6e 66 73 2f 00 6e 65 74 6d 61 73 6b 3d 32 35 |/nfs/.netmask=25| -- 000b82e0 30 2c 31 31 35 32 30 30 00 0a 50 65 72 6d 61 6e |0,115200..Perman| 000b82f0 65 6e 74 20 62 6f 6f 74 63 6d 64 3a 20 25 73 0a |ent bootcmd: %s.| 000b8300 00 0a 50 65 72 6d 61 6e 65 6e 74 20 63 6f 6e 73 |..Permanent cons| 000b8310 6f 6c 65 3a 20 25 73 0a 00 69 70 61 64 64 72 00 |ole: %s..ipaddr.| 000b8320 73 65 72 76 65 72 69 70 00 62 6f 6f 74 61 72 67 |serverip.bootarg| 000b8330 73 5f 65 6e 64 00 65 74 68 31 61 64 64 72 00 73 |s_end.eth1addr.s| -- 000cdd30 65 3d 74 74 79 53 30 2c 31 31 35 32 30 30 20 65 |e=ttyS0,115200 e| 000cdd40 61 72 6c 79 70 72 69 6e 74 6b 3d 74 74 79 53 30 |arlyprintk=ttyS0| 000cdd50 20 72 6f 6f 74 3d 2f 64 65 76 2f 73 64 61 32 20 | root=/dev/sda2 | 000cdd60 72 6f 20 70 6d 5f 64 69 73 61 62 6c 65 00 73 65 |ro pm_disable.se| 000cdd70 74 65 6e 76 20 62 6f 6f 74 61 72 67 73 20 00 62 |tenv bootargs .b| 000cdd80 6f 6f 74 5f 73 6f 75 72 63 65 5f 64 65 76 69 63 |oot_source_devic| root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd1 | grep -A 5 -i 115200 00115200 1a ac ff a6 b4 61 ae 91 fe 5d 85 7e ff f5 a7 b9 |.....a...].~....| 00115210 6c 6f b2 d3 5b 17 ed f4 ea 8d f9 69 8e d3 51 7e |lo..[......i..Q~| 00115220 79 71 55 5e 49 22 19 62 99 a7 e9 3e 7f e8 df 7b |yqU^I".b...>...{| 00115230 25 3f 43 be 9e 66 95 c6 58 ef c5 de b3 2e da e6 |%?C..f..X.......| 00115240 65 45 0f 7e b9 f8 04 93 9e 17 9b 2d 26 fa 67 24 |eE.~.......-&.g$| 00115250 fb 33 1c 6f c2 78 5e ec 82 9e 2e a3 5f 1a d7 cc |.3.o.x^....._...| -- 003e42e0 30 2c 31 31 35 32 30 30 20 65 61 72 6c 79 70 72 |0,115200 earlypr| 003e42f0 69 6e 74 6b 00 00 00 00 00 00 00 02 00 00 00 01 |intk............| 003e4300 61 6c 69 61 73 65 73 00 00 00 00 03 00 00 00 1e |aliases.........| 003e4310 00 00 00 35 2f 73 6f 63 2f 69 6e 74 65 72 6e 61 |...5/soc/interna| 003e4320 6c 2d 72 65 67 73 2f 67 70 69 6f 40 31 38 31 30 |l-regs/gpio@1810| 003e4330 30 00 00 00 00 00 00 03 00 00 00 1e 00 00 00 3b |0..............;| root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd2 | grep -A 5 -i 115200 00115200 ff ee d4 ad f6 9a 58 fa af ec bf 4b f5 32 47 41 |......X....K.2GA| 00115210 ff 77 fe 6c ef bf 4b 32 6b 62 a9 bf b0 26 96 6c |.w.l..K2kb...&.l| 00115220 ca b1 26 66 4d 2c 67 6b f3 fb ef f6 6d b1 d7 c4 |..&fM,gk....m...| 00115230 56 67 db 36 d1 ce d1 68 31 ee 5d 5c fe 68 bb 1e |Vg.6...h1.]\.h..| 00115240 b2 e0 32 ee fb 71 eb 46 d9 63 ae 37 c7 b6 61 3a |..2..q.F.c.7..a:| 00115250 9a 7a 11 5d b3 f7 85 dd 79 50 bd ec 8d 29 77 2b |.z.]....yP...)w+| root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd3 | grep -A 5 -i 115200 00115200 d0 a2 87 96 a4 4f a9 bc b8 fd 2c 75 dc 10 d5 ea |.....O....,u....| 00115210 1c 46 58 37 59 85 f5 d9 d7 cb b6 0a 90 ae 84 22 |.FX7Y.........."| 00115220 5f 36 e5 12 38 91 c0 dd 9c bf 77 4d c6 23 3c 37 |_6..8.....wM.#<7| 00115230 2a f7 d4 44 24 52 ab 16 dd 3b 26 ff 01 41 6b 13 |*..D$R...;&..Ak.| 00115240 93 65 89 5f 87 c4 b5 dd 07 71 23 75 b9 b1 27 e5 |.e._.....q#u..'.| 00115250 2a 0b 2a 7b 4d 7f 9d 9d 1a 4d 79 97 f5 9a ef f0 |*.*{M....My.....| -- 01115200 f7 62 80 58 bc 2b 6d c8 ba 9c 56 00 62 75 ed 96 |.b.X.+m...V.bu..| 01115210 1d f9 3a 5a 13 e3 ef 19 fa 86 39 66 9b aa 69 c3 |..:Z......9f..i.| 01115220 4f 11 65 b5 51 5a 46 aa d2 84 77 71 17 e3 62 e1 |O.e.QZF...wq..b.| 01115230 d0 7e 3c 4f 2b eb c5 47 ad cf e8 33 51 21 11 35 |.~<O+..G...3Q!.5| 01115240 da a0 66 71 1a 19 68 1f be ff e4 c8 07 96 f2 44 |..fq..h........D| 01115250 93 b2 c9 eb 02 3e 38 52 88 b0 1d 05 57 e4 55 de |.....>8R....W.U.| -- 01152000 06 03 f7 b7 c3 5e bd d9 40 23 f7 77 da 94 d0 c3 |.....^..@#.w....| 01152010 15 7c ac d6 a4 e2 a0 99 80 41 8d a2 27 47 f9 67 |.|.......A..'G.g| 01152020 d8 e6 77 51 57 88 a2 f1 33 92 5f fc 31 60 03 1f |..wQW...3._.1`..| 01152030 d2 57 78 e2 d9 be 2b 8c 72 40 09 9f 21 0f 2d d1 |.Wx...+.r@..!.-.| 01152040 c2 cc 35 7e 87 52 d9 46 d9 83 09 9e ab 53 f8 2e |..5~.R.F.....S..| 01152050 c8 46 69 c9 5c ee 7f 22 6f 89 a9 12 cf a1 ca e5 |.Fi.\.."o.......| -- 02115200 6c be 28 73 29 d9 bc ad e8 9f 42 8a 08 d1 f7 e0 |l.(s).....B.....| 02115210 9c 49 26 75 af 80 f4 8d bd 2b 0b 55 47 90 36 dd |.I&u.....+.UG.6.| 02115220 e2 91 87 a4 a4 d3 f1 d3 bc f4 df 55 7f 6a 24 a5 |...........U.j$.| 02115230 49 c7 d7 28 f4 38 6b 8e c9 50 a3 df c1 39 7e 4b |I..(.8k..P...9~K| 02115240 42 fd 25 ae d5 ba ab 12 ac 74 c0 f2 79 55 f5 81 |B.%......t..yU..| 02115250 4b ba 10 56 a6 22 e8 06 c8 83 a8 05 5d a2 4a af |K..V."......].J.| -- 03115200 43 aa 22 29 92 95 2a bd 04 ea 2c 13 d0 e0 8d 40 |C.")..*...,....@| 03115210 8c c9 d8 bb c8 98 93 84 15 ff 9f 28 a3 7d 1e 1e |...........(.}..| 03115220 05 1d b3 d7 5f a0 fd c0 c8 af 4d 0d bf 78 77 0e |...._.....M..xw.| 03115230 bf 07 c4 f1 81 73 56 d7 0d 5b be ee c8 3c 09 d8 |.....sV..[...<..| 03115240 fe 62 12 80 2e 36 65 0d 25 7e e0 10 89 4d 89 83 |.b...6e.%~...M..| 03115250 76 67 34 d7 f3 5d cc ab 97 84 bf 68 8c 94 b9 58 |vg4..].....h...X| -- 04115200 9c 0a 2d a9 4d e1 22 00 3d e9 82 a7 9d 61 e2 b4 |..-.M.".=....a..| 04115210 9d 91 8a 86 fb e0 cb 8d ce ca 0e 4d 44 cd 1d 8e |...........MD...| 04115220 1a f2 ac ec 68 68 0f 3b 1b e4 46 2c c8 bb 4b c2 |....hh.;..F,..K.| 04115230 85 e6 1e d9 84 88 0c 59 b1 0e 50 af ce b3 f6 6d |.......Y..P....m| 04115240 2d 27 ba 28 10 d6 13 b6 7b 50 5f 01 39 0f 81 5a |-'.(....{P_.9..Z| 04115250 87 13 86 b0 eb 76 68 c1 f2 77 d3 a4 2b 57 c1 ad |.....vh..w..+W..| -- 05115200 50 e1 bc bc ea 37 3c 18 f9 f0 92 99 e0 a3 49 5d |P....7<.......I]| 05115210 dd c5 23 ab ca 0a 95 d5 c2 50 9a 0f 7c ff 46 3d |..#......P..|.F=| 05115220 a6 fa ca fa 69 d8 05 26 00 62 93 22 15 05 26 3f |....i..&.b."..&?| 05115230 33 65 9f a6 26 71 6f 7f ec c9 7d 7b 93 71 fc ce |3e..&qo...}{.q..| 05115240 f1 26 a6 8d 02 14 ad 5f b3 c8 2f fa db 29 a3 9b |.&....._../..)..| 05115250 ff 7b 61 dc a4 21 3f 74 d1 2c da 16 0f 92 11 0f |.{a..!?t.,......| -- 1bbde200 30 2c 31 31 35 32 30 30 20 65 61 72 6c 79 70 72 |0,115200 earlypr| 1bbde210 69 6e 74 6b 00 00 00 00 00 00 00 02 00 00 00 01 |intk............| 1bbde220 61 6c 69 61 73 65 73 00 00 00 00 03 00 00 00 1e |aliases.........| 1bbde230 00 00 00 35 2f 73 6f 63 2f 69 6e 74 65 72 6e 61 |...5/soc/interna| 1bbde240 6c 2d 72 65 67 73 2f 67 70 69 6f 40 31 38 31 30 |l-regs/gpio@1810| 1bbde250 30 00 00 00 00 00 00 03 00 00 00 1e 00 00 00 3b |0..............;| -- 1c115200 97 5e d1 6a 31 f2 f6 d1 9c 7b 6c ef 1e fc e1 87 |.^.j1....{l.....| 1c115210 8d c4 2a ac 45 7f cc fb 57 3d e4 77 aa 82 81 d5 |..*.E...W=.w....| 1c115220 58 92 19 72 f8 01 97 ef d9 86 6c 7e 06 4b 58 be |X..r......l~.KX.| 1c115230 e4 04 2e 18 19 df 0d 7e c3 cb 8a 81 9b 46 8b 70 |.......~.....F.p| 1c115240 53 0d 70 c8 e1 ff a7 a4 a8 64 69 f7 f6 9c 2b 44 |S.p......di...+D| 1c115250 92 13 c1 ad 8a ba 20 99 24 b0 15 82 00 7e 90 a6 |...... .$....~..| root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd4 | grep -A 5 -i 115200 00115200 8d 66 d4 17 7f 8d 7d ac 12 18 d3 2e 2b 32 a4 d1 |.f....}.....+2..| 00115210 d9 a9 73 6b 6c b0 38 16 f5 ee 0e 1d ff 86 3a 04 |..skl.8.......:.| 00115220 d2 ec 7f dc a6 f4 b4 b7 62 6f 5e f0 70 95 1d 0c |........bo^.p...| 00115230 60 ff 04 cc 85 56 87 ad 94 81 7a 78 c6 91 0a 1f |`....V....zx....| 00115240 96 d8 10 c4 f7 d5 39 55 ce 4c e0 fa 25 d7 1d 4e |......9U.L..%..N| 00115250 b3 ed d9 68 7b 5e 8e aa 7f 1c da fe 04 f2 e7 d4 |...h{^..........| -- 003be200 30 2c 31 31 35 32 30 30 20 65 61 72 6c 79 70 72 |0,115200 earlypr| 003be210 69 6e 74 6b 00 00 00 00 00 00 00 02 00 00 00 01 |intk............| 003be220 61 6c 69 61 73 65 73 00 00 00 00 03 00 00 00 1e |aliases.........| 003be230 00 00 00 35 2f 73 6f 63 2f 69 6e 74 65 72 6e 61 |...5/soc/interna| 003be240 6c 2d 72 65 67 73 2f 67 70 69 6f 40 31 38 31 30 |l-regs/gpio@1810| 003be250 30 00 00 00 00 00 00 03 00 00 00 1e 00 00 00 3b |0..............;| root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd5 | grep -A 5 -i 115200 root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd6 | grep -A 5 -i 115200 root@debian:/media/ex4100nandbackup/no_oob_ecc# hexdump -C mtd7 | grep -A 5 -i 115200 root@debian:/media/ex4100nandbackup/no_oob_ecc#
Re: Debian on WD MyCloud EX 4100 June 20, 2017 04:21PM |
Admin Registered: 13 years ago Posts: 18,994 |
# MTD device name Device offset Env. size Flash sector size $ /dev/mtd0 0xa0000 0x20000 0x20000 fw_printenv Warning: Bad CRC, using default environment bootargs= bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=3 baudrate=115200 stdin=serial,cros-ec-keyb stdout=serial,lcd stderr=serial,lcd nano /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size $ /dev/mtd0 0xc0000 0x20000 0x20000 fw_printenv Warning: Bad CRC, using default environment bootargs= bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=3 baudrate=115200 stdin=serial,cros-ec-keyb stdout=serial,lcd stderr=serial,lcd