Re: My Cloud Mirror Gen2 July 18, 2017 12:14AM |
Registered: 7 years ago Posts: 119 |
Quote
mcmg2
it shows 512MB not 2GB
--- a/tools/marvell/bin_hdr/inc/common/ddr3_hws_hw_training_def.h +++ b/tools/marvell/bin_hdr/inc/common/ddr3_hws_hw_training_def.h @@ -97,7 +97,7 @@ #define REG_SDRAM_ADDRESS_CTRL_ADDR 0x1410 #define REG_SDRAM_ADDRESS_SIZE_OFFS 2 -#if 0 //ALPHA_CUSTOMIZE +#if 1 //ALPHA_CUSTOMIZE /* DRAM: 1GB */ #define REG_SDRAM_ADDRESS_SIZE_HIGH_OFFS 21 #else
Quote
mcmg2
after apt-get install build-essential
still not able to build deb
mcmg2
Re: My Cloud Mirror Gen2 July 18, 2017 12:40AM |
mcmg2
Re: My Cloud Mirror Gen2 July 18, 2017 05:50AM |
mint@mint ~/kwboot $ sudo ./kwboot -f -t -B 115200 /dev/ttyUSB0 -b u-boot-a38x-GrandTeton_2014T3_PQ-nand-uart.bin -s 0 -q 1 Sending boot message. Please reboot the target...| Sending boot image... 0 % [+.....................................................................] 0 % [......................................................................] 1 % [......................................................................] 2 % [......................................................................] 3 % [......................................................................] 4 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 7 % [......................................................................] 8 % [......................................................................] 9 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 12 % [......................................................................] 13 % [......................................................................] 14 % [......................................................................] 15 % [......................................................................] 15 % [......................................................................] 16 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 19 % [......................................................................] 20 % [......................................................................] 21 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 24 % [......................................................................] 25 % [......................................................................] 26 % [......................................................................] 27 % [......................................................................] 28 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 30 % [......................................................................] 31 % [......................................................................] 32 % [......................................................................] 33 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 36 % [......................................................................] 37 % [......................................................................] 38 % [......................................................................] 39 % [......................................................................] 40 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 43 % [......................................................................] 44 % [......................................................................] 45 % [......................................................................] 45 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 48 % [......................................................................] 49 % [......................................................................] 50 % [......................................................................] 51 % [......................................................................] 52 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 55 % [......................................................................] 56 % [......................................................................] 57 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 60 % [......................................................................] 60 % [......................................................................] 61 % [......................................................................] 62 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 65 % [......................................................................] 66 % [......................................................................] 67 % [......................................................................] 68 % [......................................................................] 69 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 72 % [......................................................................] 73 % [......................................................................] 74 % [......................................................................] 75 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 77 % [......................................................................] 78 % [......................................................................] 79 % [......................................................................] 80 % [......................................................................] 81 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 84 % [......................................................................] 85 % [......................................................................] 86 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 89 % [......................................................................] 90 % [......................................................................] 91 % [......................................................................] 91 % [......................................................................] 92 % [......................................................................] 93 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 96 % [......................................................................] 97 % [......................................................................] 98 % [......................................................................] 99 % [..........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-g7c1da33-dirty_v1.04 (Jul 17 2017 - 18:43:06) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fece000:0x1ff96010 BSS: 0x1ffef654 Stack: 0x1f9cdf20 Heap: 0x1f9ce000:0x1fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev 'usb' Marvell>> setenv device '0:1' Marvell>> setenv load_image_addr '0x02000000' Marvell>> setenv load_initrd_addr '0x2900000' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' Marvell>> run bootcmd_usb Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3920526 bytes read in 422 ms (8.9 MiB/s) loading uInitrd ... 6210503 bytes read in 493 ms (12 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-07-09 9:45:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3920462 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Western Digital MyCloud EX2 Ultra [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/printk/printk.c:2612 register_console+0x3c/0x398 [ 0.000000] console 'earlycon0' already registered [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.9.0-mvebu-tld-12 #2 [ 0.000000] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000] [<c01160bc>] (unwind_backtrace) from [<c0110bb4>] (show_stack+0x10/0x14) [ 0.000000] [<c0110bb4>] (show_stack) from [<c04ba5a4>] (dump_stack+0x70/0x8c) [ 0.000000] [<c04ba5a4>] (dump_stack) from [<c0123ce0>] (__warn+0xc8/0xfc) [ 0.000000] [<c0123ce0>] (__warn) from [<c0123d48>] (warn_slowpath_fmt+0x34/0x44) [ 0.000000] [<c0123d48>] (warn_slowpath_fmt) from [<c0171b1c>] (register_console+0x3c/0x398) [ 0.000000] [<c0171b1c>] (register_console) from [<c0c04dc0>] (setup_early_printk+0x14/0x24) [ 0.000000] [<c0c04dc0>] (setup_early_printk) from [<c0c00478>] (do_early_param+0x6c/0xbc) [ 0.000000] [<c0c00478>] (do_early_param) from [<c013f774>] (parse_args+0x2dc/0x40c) [ 0.000000] [<c013f774>] (parse_args) from [<c0c0088c>] (parse_early_options+0x2c/0x3c) [ 0.000000] [<c0c0088c>] (parse_early_options) from [<c0c008c8>] (parse_early_param+0x2c/0x44) [ 0.000000] [<c0c008c8>] (parse_early_param) from [<c0c03350>] (setup_arch+0x4fc/0xa24) [ 0.000000] [<c0c03350>] (setup_arch) from [<c0c00934>] (start_kernel+0x50/0x390) [ 0.000000] [<c0c00934>] (start_kernel) from [<0000807c>] (0x807c) [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @dfbcc000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 libata.force=3.0G root=LABEL=rootfs earlyprintk console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 500128K/524288K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 24160K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007883] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019112] Console: colour dummy device 80x30 [ 0.023627] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.034036] pid_max: default: 32768 minimum: 301 [ 0.038804] Security Framework initialized [ 0.043004] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.049678] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.057251] CPU: Testing write buffer coherency: ok [ 0.062343] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.068084] Setting up static identity map for 0x100000 - 0x100058 [ 0.074514] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.079798] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283603] Booting CPU 1 [ 0.286473] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286529] Brought up 2 CPUs [ 0.295290] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301610] CPU: All CPU(s) started in SVC mode. [ 0.306846] devtmpfs: initialized [ 0.312747] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320731] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330670] prandom: seed boundary self test passed [ 0.337632] prandom: 100 self tests passed [ 0.341793] pinctrl core: initialized pinctrl subsystem [ 0.347821] NET: Registered protocol family 16 [ 0.352986] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.383454] cpuidle: using governor ladder [ 0.413421] cpuidle: using governor menu [ 0.417536] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.425611] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.483823] vgaarb: loaded [ 0.486863] SCSI subsystem initialized [ 0.491159] usbcore: registered new interface driver usbfs [ 0.496815] usbcore: registered new interface driver hub [ 0.502248] usbcore: registered new device driver usb [ 0.507598] media: Linux media interface: v0.10 [ 0.512243] Linux video capture interface: v2.00 [ 0.517916] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.554069] VFS: Disk quotas dquot_6.6.0 [ 0.558140] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.573419] NET: Registered protocol family 2 [ 0.578292] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.585414] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.591979] TCP: Hash tables configured (established 4096 bind 4096) [ 0.598428] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.604328] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.610779] NET: Registered protocol family 1 [ 0.615463] RPC: Registered named UNIX socket transport module. [ 0.621458] RPC: Registered udp transport module. [ 0.626223] RPC: Registered tcp transport module. [ 0.631015] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.637640] Unpacking initramfs... [ 0.882396] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.888538] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.895240] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.904558] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.910806] audit: initializing netlink subsys (disabled) [ 0.916287] audit: type=2000 audit(0.900:1): initialized [ 0.922133] Initialise system trusted keyrings [ 0.926798] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.933392] zbud: loaded [ 0.936552] NFS: Registering the id_resolver key type [ 0.941691] Key type id_resolver registered [ 0.945938] Key type id_legacy registered [ 0.950032] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.956786] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.963365] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.970810] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.977427] orangefs_init: module version upstream loaded [ 0.985067] Key type asymmetric registered [ 0.989245] Asymmetric key parser 'x509' registered [ 0.994273] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.001730] io scheduler noop registered [ 1.005719] io scheduler deadline registered [ 1.010076] io scheduler cfq registered (default) [ 1.015764] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.024448] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.031399] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.037723] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.044660] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.050661] PCI: bus0: Fast back to back transfers disabled [ 1.056299] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.064371] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.072555] PCI: bus1: Fast back to back transfers enabled [ 1.078240] PCI: bus2: Fast back to back transfers enabled [ 1.083829] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.088876] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.094396] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.158408] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.166031] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.228386] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.287076] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.294965] console [ttyS0] disabled [ 1.318731] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 12500000) is a 16550A [ 1.327756] console [ttyS0] enabled [ 1.327756] console [ttyS0] enabled [ 1.334859] bootconsole [earlycon0] disabled [ 1.334859] bootconsole [earlycon0] disabled [ 1.364242] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 12500000) is a 16550A [ 1.374256] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.383363] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.393069] scsi host0: ahci-mvebu [ 1.396807] scsi host1: ahci-mvebu [ 1.400464] ata1: FORCE: PHY spd limit set to 3.0Gbps [ 1.405540] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.413505] ata2: FORCE: PHY spd limit set to 3.0Gbps [ 1.418587] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.427081] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.434994] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 1.441388] nand: Hynix H27U2G8F2CTR-BC [ 1.445242] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.452857] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.460059] Bad block table found at page 131008, version 0x01 [ 1.466260] Bad block table found at page 130944, version 0x01 [ 1.472364] 8 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.478495] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 1.483920] 0x000000000000-0x000000500000 : "U-Boot" [ 1.489744] 0x000000500000-0x000000a00000 : "uImage" [ 1.505468] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 1.521356] 0x000000f00000-0x00000c800000 : "image.cfs" [ 1.538089] 0x00000c800000-0x00000d700000 : "rescue fw" [ 1.554081] 0x00000d700000-0x00000eb00000 : "config" [ 1.569869] 0x00000eb00000-0x00000f500000 : "reserve1" [ 1.585787] 0x00000f500000-0x00000ff00000 : "reserve2" [ 1.602327] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.609141] libphy: Fixed MDIO Bus: probed [ 1.613567] libphy: mdio_driver_register: mv88e6085 [ 1.618728] libphy: orion_mdio_bus: probed [ 1.627771] mvneta f1034000.ethernet eth0: Using random mac address 1a:ab:35:b9:8e:f4 [ 1.635900] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.642483] ehci-pci: EHCI PCI platform driver [ 1.646992] ehci-orion: EHCI orion driver [ 1.651337] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.656687] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 1.664297] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.672911] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000 [ 1.678800] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.685619] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.692883] usb usb1: Product: xHCI Host Controller [ 1.697782] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.704260] usb usb1: SerialNumber: f10f0000.usb3 [ 1.709377] hub 1-0:1.0: USB hub found [ 1.713165] hub 1-0:1.0: 1 port detected [ 1.717296] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.722656] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.730241] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.738445] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.745265] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.749208] ata1: SATA link down (SStatus 0 SControl 320) [ 1.757975] usb usb2: Product: xHCI Host Controller [ 1.759162] ata2: SATA link down (SStatus 0 SControl 320) [ 1.768299] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.774768] usb usb2: SerialNumber: f10f0000.usb3 [ 1.779856] hub 2-0:1.0: USB hub found [ 1.783640] hub 2-0:1.0: 1 port detected [ 1.787854] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.793217] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 1.800815] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.809433] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000 [ 1.815294] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.822170] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.829433] usb usb3: Product: xHCI Host Controller [ 1.834332] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.840809] usb usb3: SerialNumber: f10f8000.usb3 [ 1.845869] hub 3-0:1.0: USB hub found [ 1.849670] hub 3-0:1.0: 1 port detected [ 1.853802] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.859157] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.866724] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.874930] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.881764] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.889096] usb usb4: Product: xHCI Host Controller [ 1.893995] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.900475] usb usb4: SerialNumber: f10f8000.usb3 [ 1.905539] hub 4-0:1.0: USB hub found [ 1.909335] hub 4-0:1.0: 1 port detected [ 1.913570] usbcore: registered new interface driver usblp [ 1.919170] usbcore: registered new interface driver usb-storage [ 1.925394] mousedev: PS/2 mouse device common for all mice [ 1.931594] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 1.939413] i2c /dev entries driver [ 1.954882] orion_wdt: Initial timeout 171 sec [ 1.961316] marvell-cesa f1090000.crypto: CESA device successfully registered [ 1.968693] hidraw: raw HID events driver (C) Jiri Kosina [ 1.974440] usbcore: registered new interface driver usbhid [ 1.980052] usbhid: USB HID core driver [ 1.984064] drop_monitor: Initializing network drop monitor service [ 1.990413] Netfilter messages via NETLINK v0.30. [ 1.995151] ip_set: protocol 6 [ 1.998482] NET: Registered protocol family 10 [ 2.003518] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.010502] NET: Registered protocol family 17 [ 2.015131] 8021q: 802.1Q VLAN Support v1.8 [ 2.019464] Key type dns_resolver registered [ 2.023885] ThumbEE CPU extension supported. [ 2.028191] Registering SWP/SWPB emulation handler [ 2.033529] registered taskstats version 1 [ 2.037646] Loading compiled-in X.509 certificates [ 2.042508] zswap: loaded using pool lzo/zbud [ 2.095311] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 2.105784] Key type big_key registered [ 2.113426] Key type encrypted registered [ 2.118576] armada38x-rtc f10a3800.rtc: setting system clock to 2017-07-18 19:39:32 UTC (1500406772) [ 2.128956] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.171648] systemd-udevd[1315]: starting version 215 [ 2.177740] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.270270] usb 1-1: New USB device found, idVendor=090c, idProduct=1000 [ 2.277017] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.285512] usb 1-1: Product: POLLEX 8G [ 2.289392] usb 1-1: Manufacturer: SRT [ 2.293158] usb 1-1: SerialNumber: 033113111111135234000373 [ 2.299280] usb-storage 1-1:1.0: USB Mass Storage device detected [ 2.319351] scsi host2: usb-storage 1-1:1.0 [ 2.484375] usbcore: registered new interface driver uas [ 3.368663] scsi 2:0:0:0: Direct-Access SRT POLLEX 8G 1100 PQ: 0 ANSI: 4 [ 3.381265] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 3.386626] sd 2:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) [ 3.395583] sd 2:0:0:0: [sda] Write Protect is off [ 3.401106] sd 2:0:0:0: [sda] No Caching mode page found [ 3.406443] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 3.415836] sda: sda1 [ 3.420704] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 3.459375] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.593452] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.610997] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 17.916366] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR) [ 17.929957] systemd[1]: Detected architecture 'arm'. Welcome to Debian GNU/Linux 8 (jessie)! [ 17.979130] systemd[1]: Set hostname to <debian>. [ 18.329472] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory. [ 18.346180] systemd[1]: Starting Forward Password Requests to Wall Directory Watch. [ 18.354165] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 18.361854] systemd[1]: Expecting device dev-ttyS0.device... Expecting device dev-ttyS0.device... [ 18.397996] systemd[1]: Starting Remote File Systems (Pre). [ OK ] Reached target Remote File Systems (Pre). [ 18.437972] systemd[1]: Reached target Remote File Systems (Pre). [ 18.444191] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point. [ OK ] Set up automount Arbitrary Executable File Formats F...utomount Point. [ OK ] Reached target Swap. [ OK ] Created slice Root Slice. [ OK ] Created slice User and Session Slice. [ OK ] Listening on Delayed Shutdown Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on LVM2 metadata daemon socket. [ OK ] Listening on Device-mapper event daemon FIFOs. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on Journal Socket. [ OK ] Created slice System Slice. [ OK ] Created slice system-getty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. Starting Increase datagram queue length... Starting Nameserver information manager... Mounting Debug File System... Starting Create list of required static device nodes...rrent kernel... Starting udev Coldplug all Devices... Starting Load Kernel Modules... Mounting POSIX Message Queue File System... Starting Remount Root and Kernel File Systems... [ OK ] Reached target Slices. [ 19.215680] fuse init (API version 7.26) [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Started Increase datagram queue length. [ OK ] Started Create list of required static device nodes ...current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Nameserver information manager. [ OK ] Started udev Coldplug all Devices. Starting udev Wait for Complete Device Initialization... Starting Initial Check File System Quotas... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Mounting FUSE Control File System... Starting Create Static Device Nodes in /dev... [ OK ] Listening on Syslog Socket. Starting Journal Service... [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [FAILED] Failed to start Load/Save Random Seed. See 'systemctl status systemd-random-seed.service' for details. [FAILED] Failed to start Initial Check File System Quotas. See 'systemctl status quota.service' for details. [ OK ] Started Apply Kernel Variables. [ 20.106433] quota-initial-check.sh[1419]: Checking quotas...done. [ OK ] Started Create Static Device Nodes in /dev. [ 20.151001] quota-initial-check.sh[1419]: rm: cannot remove ‘/var/lib/quota/new’: Read-only file system Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ 20.277311] systemd-udevd[1441]: starting version 215 Mounting /tmp... [ OK ] Started udev Kernel Device Manager. [ OK ] Mounted /tmp. [ OK ] Started udev Wait for Complete Device Initialization. Starting Activation of LVM2 logical volumes... Starting Copy rules generated while the root was ro... Starting LSB: Tune IDE hard disks... Starting LSB: MD array assembly... [ OK ] Started Copy rules generated while the root was ro. [ OK ] Found device /dev/ttyS0. [ OK ] Started Activation of LVM2 logical volumes. [ OK ] Reached target Encrypted Volumes. Starting Activation of LVM2 logical volumes... [ OK ] Started LSB: Tune IDE hard disks. [ OK ] Started Activation of LVM2 logical volumes. [ OK ] Started LSB: MD array assembly. Starting Monitoring of LVM2 mirrors, snapshots etc. ...ress polling... [ OK ] Started Monitoring of LVM2 mirrors, snapshots etc. u...ogress polling. [ OK ] Reached target Local File Systems. Starting Cleanup PHP session files... Starting Cleanup monit state file... Starting Create Volatile Files and Directories... [ OK ] Reached target Remote File Systems. Starting Trigger Flushing of Journal to Persistent Storage... Starting LSB: Raise network interfaces.... [ OK ] Started Cleanup PHP session files. [FAILED] Failed to start Cleanup monit state file. See 'systemctl status openmediavault-cleanup-monit.service' for details. [ OK ] Started Create Volatile Files and Directories. [ 21.643550] systemd-journald[1435]: Received request to flush runtime journal from PID 1 Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Trigger Flushing of Journal to Persistent Storage. [FAILED] Failed to start Update UTMP about System Boot/Shutdown. See 'systemctl status systemd-update-utmp.service' for details. [DEPEND] Dependency failed for Update UTMP about System Runlevel Changes. [ 26.168386] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ OK ] Started LSB: Raise network interfaces.. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting LSB: RPC portmapper replacement... [ 31.275765] random: crng init done [ OK ] Started LSB: RPC portmapper replacement. [ OK ] Reached target RPC Port Mapper. Starting LSB: NFS support files common to client and server... [ OK ] Started LSB: NFS support files common to client and server. [ OK ] Reached target System Initialization. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on ACPID Listen Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Timers. [ OK ] Reached target Paths. [ OK ] Reached target Basic System. Starting The OpenMediaVault engine daemon that proce... RPC request... Starting A high performance web server and a reverse proxy server... Starting Run anacron jobs... [ OK ] Started Run anacron jobs. Starting Self Monitoring and Reporting Technology (SMART) Daemon... [ OK ] Started Self Monitoring and Reporting Technology (SMART) Daemon. Starting The PHP FastCGI Process Manager... Starting Regular background program processing daemon... [ OK ] Started Regular background program processing daemon. Starting RPC Remote Quota Server... Starting OpenBSD Secure Shell server... [ OK ] Started OpenBSD Secure Shell server. Starting /etc/rc.local Compatibility... Starting Login Service... Starting LSB: Start NTP daemon... Starting LSB: Courier IMAP server... Starting LSB: Ajenti... Starting LSB: start the RRDtool data caching daemon... Starting LSB: SNMP agents... Starting LSB: Start and stop the mysql database server daemon... Starting LSB: Start/stop supervisor... Starting LSB: start Samba daemons for the AD DC... Starting (null)... Starting LSB: service and resource monitoring daemon... Starting LSB: Load kernel modules needed to enable cpufreq scaling... Starting LSB: Kernel NFS server support... Starting LSB: start Samba NetBIOS nameserver (nmbd)... Starting LSB: Starts syslogd... Starting LSB: Starts ProFTPD daemon... Starting LSB: Courier IMAP-SSL server... Starting Avahi mDNS/DNS-SD Stack... Starting D-Bus System Message Bus... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Avahi mDNS/DNS-SD Stack. Starting System Logging Service... Starting Permit User Sessions... Starting ACPI event daemon... [ OK ] Started ACPI event daemon. [FAILED] Failed to start A high performance web server and a ...e proxy server. See 'systemctl status nginx.service' for details. [ OK ] Started RPC Remote Quota Server. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started LSB: Start NTP daemon. [ OK ] Started LSB: Courier IMAP server. [FAILED] Failed to start LSB: start the RRDtool data caching daemon. See 'systemctl status rrdcached.service' for details. [ OK ] Started (null). [ OK ] Started LSB: service and resource monitoring daemon. [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling. [ OK ] Started LSB: Kernel NFS server support. [ OK ] Started LSB: Starts syslogd. [ OK ] Started LSB: Courier IMAP-SSL server. [ OK ] Started Permit User Sessions. [ OK ] Started Login Service. [ OK ] Started System Logging Service. Mounting Arbitrary Executable File Formats File System... Starting LSB: Starts klogd... Starting LSB: set CPUFreq kernel parameters... Starting Getty on tty1... [ OK ] Started Getty on tty1. Starting Serial Getty on ttyS0... [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started The OpenMediaVault engine daemon that proces...he RPC request. [ OK ] Started LSB: Starts klogd. [FAILED] Failed to start The PHP FastCGI Process Manager. See 'systemctl status php5-fpm.service' for details. [ OK ] Mounted Arbitrary Executable File Formats File System. [ OK ] Started LSB: set CPUFreq kernel parameters. [ OK ] Started LSB: SNMP agents. [FAILED] Failed to start LSB: Starts ProFTPD daemon. See 'systemctl status proftpd.service' for details. Starting LSB: manage the statistics collection daemon... [ OK ] Started LSB: manage the statistics collection daemon. [FAILED] Failed to start LSB: Start/stop supervisor. See 'systemctl status supervisor.service' for details. [ OK ] Started LSB: Ajenti. [ OK ] Started LSB: start Samba daemons for the AD DC. [FAILED] Failed to start LSB: start Samba NetBIOS nameserver (nmbd). See 'systemctl status nmbd.service' for details. Starting LSB: start Samba SMB/CIFS daemon (smbd)... [FAILED] Failed to start LSB: start Samba SMB/CIFS daemon (smbd). See 'systemctl status smbd.service' for details. openmediavault 3.0.84 (Erasmus) debian ttyS0 Copyright (C) 2009-2017 by Volker Theile. All rights reserved. To manage the system visit the openmediavault web control panel: No network interface(s) available By default the web control panel administrator account has the username 'admin' and password 'openmediavault'. It is recommended that you change the password for this account within the web control panel or using the 'omv-firstaid' CLI command. For more information regarding this appliance, please visit the web site: http://www.openmediavault.org debian login: root Password: Linux debian 4.9.0-mvebu-tld-12 #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian 192.168.2.209 Western Digital MyCloud EX2 Ultra Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 10:45:37 up 1 min, 1 user, load average: 0.73, 0.24, 0.08 root@debian:~# df -h Filesystem Size Used Avail Use% Mounted on udev 10M 0 10M 0% /dev tmpfs 100M 5.4M 94M 6% /run /dev/sda1 7.3G 2.2G 4.8G 31% / tmpfs 248M 0 248M 0% /dev/shm tmpfs 5.0M 0 5.0M 0% /run/lock tmpfs 248M 0 248M 0% /sys/fs/cgroup tmpfs 248M 0 248M 0% /tmp root@debian:~/mcm-daemon# omv-initsystem /usr/sbin/omv-initsystem: 38: /usr/sbin/omv-initsystem: cannot create /var/log/openmediavault/initsystem.log: Read-only file system root@debian:~/mcm-daemon#
Re: My Cloud Mirror Gen2 July 18, 2017 03:31PM |
Registered: 7 years ago Posts: 119 |
Quote
mcmg2
please advise me to skip kwboot.
root@debian:~# mtd_debug info /dev/mtd0 mtd.type = MTD_NANDFLASH mtd.flags = MTD_CAP_ROM mtd.size = 5242880 (5M) mtd.erasesize = 131072 (128K) mtd.writesize = 2048 (2K) mtd.oobsize = 64 regions = 0
# mtd_debug info /dev/mtd0 mtd.type = MTD_NANDFLASH mtd.flags = MTD_CAP_NANDFLASH mtd.size = 5242880 (5M) mtd.erasesize = 131072 (128K) mtd.writesize = 2048 (2K) mtd.oobsize = 64 regions = 0
# nanddump -s 0x100000 -l 0x80000 -f ubootenv.bin /dev/mtd0
# flash_erase /dev/mtd0 0 8 # nandwrite -p /dev/mtd0 u-boot-a38x-GrandTeton_2014T3_PQ-nand.bin
# nandwrite -p /dev/mtd0 -s 0x100000 ubootenv.bin
mcmg2
Re: My Cloud Mirror Gen2 July 18, 2017 05:50PM |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-g7c1da33-dirty_v1.04 (Jul 17 2017 - 18:43:06) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fece000:0x1ff96010 BSS: 0x1ffef654 Stack: 0x1f9cdf20 Heap: 0x1f9ce000:0x1fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x500000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux-382 Created: 2015-08-02 3:54:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4093292 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Ramdisk Created: 2015-10-13 10:23:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 2278194 Bytes = 2.2 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Sun Aug 2 11:53:57 CST 2015 2014T30p5 Build-git3e9fe59 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 1 pages/cpu @c0930000 s8320 r8192 d16256 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16364 Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial PID hash table entries: 2048 (order: -2, 8192 bytes) Dentry cache hash table entries: 65536 (order: 3, 262144 bytes) Inode-cache hash table entries: 32768 (order: 2, 131072 bytes) allocated 131072 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 512MB = 512MB total Memory: 511744k/511744k available, 12544k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff8000 ( 32 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0714278 (7217 kB) .init : 0xc0718000 - 0xc075a080 ( 265 kB) .data : 0xc075c000 - 0xc07a7e40 ( 304 kB) .bss : 0xc07a7e40 - 0xc0871570 ( 806 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p5 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 4096 Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc056c2b0 - 0xc056c308 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (5311.69 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 xor: measuring software checksum speed arm4regs : 1420.800 MB/sec 8regs : 940.800 MB/sec 32regs : 918.400 MB/sec xor: using function: arm4regs (1420.800 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ196, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ228, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 355 MB/s raid6: int32x2 347 MB/s raid6: int32x4 447 MB/s raid6: int32x8 384 MB/s raid6: using algorithm int32x4 (447 MB/s) raid6: using intx1 recovery algorithm mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Switching to clocksource armada_370_xp_clocksource NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 0, 32768 bytes) TCP bind hash table entries: 4096 (order: 0, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 1024 (order: 0, 32768 bytes) UDP-Lite hash table entries: 1024 (order: 0, 32768 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 2176K (c0f08000 - c1128000) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 8192 (order 0, 32768 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.22) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 1002 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC Nand Flash Timing = [WP : 12], [WH : 10] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 8 ofpart partitions found on MTD device armada-nand Creating 8 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "U-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "uRamdisk" 0x000000f00000-0x00000c800000 : "image.cfs" 0x00000c800000-0x00000d700000 : "rescue fw" 0x00000d700000-0x00000eb00000 : "config" 0x00000eb00000-0x00000f500000 : "reserve1" 0x00000f500000-0x00000ff00000 : "reserve2" SoC: model = 0x6820, revision = 0x4 mvPncVirtBase = 0xe0e00000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=2 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o egiga0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) port #1: is_sgmii=0, is_rgmii=1, phy_addr=1 o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048 o Port 1 is connected to Linux netdevice o egiga1, ifindex = 3, GbE port = 1 giga p=1: mtu=1500, mac=00:50:43:02:02:02 (platform) port #2: is_sgmii=1, is_rgmii=0, phy_addr=0 o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 o Port 2 is connected to Linux netdevice o egiga2, ifindex = 4, GbE port = 2 giga p=2: mtu=1500, mac=00:50:43:02:02:03 (platform) libphy: orion_mdio_bus: probed mdio_bus f1072004.mdio-mi: cannot get PHY at address 2 mdio_bus f1072004.mdio-mi: cannot get PHY at address 1 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 hub 5-0:1.0: USB hub found ata2: SATA link down (SStatus 0 SControl 300) hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage ata1: SATA link down (SStatus 0 SControl 300) usb 2-1: new high-speed USB device number 2 using xhci-hcd usb 2-1: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes usb 2-1: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes usb-storage 2-1:1.0: USB Mass Storage device detected scsi2 : usb-storage 2-1:1.0 mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c0734f0c) TCP: cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 registered taskstats version 1 mvebu-rtc f10a3800.rtc: setting system clock to 2017-07-18 22:16:38 UTC (1500416198) Waiting 10sec before mounting root device... scsi 2:0:0:0: Direct-Access SRT POLLEX 8G 1100 PQ: 0 ANSI: 4 sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] Attached SCSI removable disk md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. RAMDISK: gzip image found at block 0 VFS: Mounted root (ext2 filesystem) on device 1:0. linuxrc: applet VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6 not found Please append a correct "root=" boot option; here are the available partitions: 1f00 5120 mtdblock0 (driver?) 1f01 5120 mtdblock1 (driver?) 1f02 5120 mtdblock2 (driver?) 1f03 189440 mtdblock3 (driver?) 1f04 15360 mtdblock4 (driver?) 1f05 20480 mtdblock5 (driver?) 1f06 10240 mtdblock6 (driver?) 1f07 10240 mtdblock7 (driver?) 0800 7864320 sda driver: sd 0801 7863296 sda1 0001bf63-01 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) CPU0: stopping CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.39 #1 [<c0015130>] (unwind_backtrace+0x0/0xfc) from [<c0011768>] (show_stack+0x10/0x18) [<c0011768>] (show_stack+0x10/0x18) from [<c0013908>] (handle_IPI+0x100/0x134) [<c0013908>] (handle_IPI+0x100/0x134) from [<c0008624>] (gic_handle_irq+0x5c/0x64) [<c0008624>] (gic_handle_irq+0x5c/0x64) from [<c000dd40>] (__irq_svc+0x40/0x50) Exception stack(0xc075df70 to 0xc075dfb8) df60: ffffffed 001d8000 c076790c c0019c20 df80: c075c000 c0766564 c0570d74 c07a7d2a c07a7d2a 414fc091 00000001 00000000 dfa0: 01000000 c075dfb8 c000f344 c000f330 60000113 ffffffff [<c000dd40>] (__irq_svc+0x40/0x50) from [<c000f330>] (arch_cpu_idle+0x28/0x48) [<c000f330>] (arch_cpu_idle+0x28/0x48) from [<c0056754>] (cpu_startup_entry+0x4c/0x11c) [<c0056754>] (cpu_startup_entry+0x4c/0x11c) from [<c0718a54>] (start_kernel+0x2e4/0x34c) [<c0718a54>] (start_kernel+0x2e4/0x34c) from [<00008074>] (0x8074) BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6820 High speed PHY - Version: 2.0 Load WD GrandTeton Serdes Config: board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | PCIe0 | | 2 | 06 | SATA1 | | 3 | 05 | USB3 HOST1 | | 4 | 05 | USB3 HOST0 | | 5 | 00 | SGMII2 | -------------------------------- PCIe, Idx 0: detected no link High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED
| \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-g7c1da33-dirty_v1.04 (Jul 17 2017 - 18:43:06) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fece000:0x1ff96010 BSS: 0x1ffef654 Stack: 0x1f9cdf20 Heap: 0x1f9ce000:0x1fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_usb=echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:20:21:3e eth1mtu=1500 eth2addr=00:50:43:20:f2:3e eth2mtu=1500 eth3addr=00:50:43:21:f2:20 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:f2:21:3e ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:3e:f2:20 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4028/524284 bytes Marvell>> run bootcmd_usb Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3920526 bytes read in 421 ms (8.9 MiB/s) loading uInitrd ... 6210503 bytes read in 498 ms (11.9 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-07-09 9:45:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3920462 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Western Digital MyCloud EX2 Ultra [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/printk/printk.c:2612 register_console+0x3c/0x398 [ 0.000000] console 'earlycon0' already registered [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.9.0-mvebu-tld-12 #2 [ 0.000000] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000] [<c01160bc>] (unwind_backtrace) from [<c0110bb4>] (show_stack+0x10/0x14) [ 0.000000] [<c0110bb4>] (show_stack) from [<c04ba5a4>] (dump_stack+0x70/0x8c) [ 0.000000] [<c04ba5a4>] (dump_stack) from [<c0123ce0>] (__warn+0xc8/0xfc) [ 0.000000] [<c0123ce0>] (__warn) from [<c0123d48>] (warn_slowpath_fmt+0x34/0x44) [ 0.000000] [<c0123d48>] (warn_slowpath_fmt) from [<c0171b1c>] (register_console+0x3c/0x398) [ 0.000000] [<c0171b1c>] (register_console) from [<c0c04dc0>] (setup_early_printk+0x14/0x24) [ 0.000000] [<c0c04dc0>] (setup_early_printk) from [<c0c00478>] (do_early_param+0x6c/0xbc) [ 0.000000] [<c0c00478>] (do_early_param) from [<c013f774>] (parse_args+0x2dc/0x40c) [ 0.000000] [<c013f774>] (parse_args) from [<c0c0088c>] (parse_early_options+0x2c/0x3c) [ 0.000000] [<c0c0088c>] (parse_early_options) from [<c0c008c8>] (parse_early_param+0x2c/0x44) [ 0.000000] [<c0c008c8>] (parse_early_param) from [<c0c03350>] (setup_arch+0x4fc/0xa24) [ 0.000000] [<c0c03350>] (setup_arch) from [<c0c00934>] (start_kernel+0x50/0x390) [ 0.000000] [<c0c00934>] (start_kernel) from [<0000807c>] (0x807c) [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @dfbcc000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 libata.force=3.0G root=LABEL=rootfs earlyprintk console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 500128K/524288K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 24160K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000004] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007883] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019111] Console: colour dummy device 80x30 [ 0.023627] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.034034] pid_max: default: 32768 minimum: 301 [ 0.038803] Security Framework initialized [ 0.043003] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.049678] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.057253] CPU: Testing write buffer coherency: ok [ 0.062343] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.068085] Setting up static identity map for 0x100000 - 0x100058 [ 0.074518] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.079801] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283603] Booting CPU 1 [ 0.286473] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286531] Brought up 2 CPUs [ 0.295292] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301613] CPU: All CPU(s) started in SVC mode. [ 0.306844] devtmpfs: initialized [ 0.312765] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320754] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330692] prandom: seed boundary self test passed [ 0.337654] prandom: 100 self tests passed [ 0.341815] pinctrl core: initialized pinctrl subsystem [ 0.347847] NET: Registered protocol family 16 [ 0.353037] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.383453] cpuidle: using governor ladder [ 0.413420] cpuidle: using governor menu [ 0.417551] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.425625] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.483820] vgaarb: loaded [ 0.486860] SCSI subsystem initialized [ 0.491161] usbcore: registered new interface driver usbfs [ 0.496818] usbcore: registered new interface driver hub [ 0.502254] usbcore: registered new device driver usb [ 0.507605] media: Linux media interface: v0.10 [ 0.512250] Linux video capture interface: v2.00 [ 0.517950] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.554179] VFS: Disk quotas dquot_6.6.0 [ 0.558251] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.573572] NET: Registered protocol family 2 [ 0.578434] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.585556] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.592117] TCP: Hash tables configured (established 4096 bind 4096) [ 0.598564] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.604464] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.610911] NET: Registered protocol family 1 [ 0.615597] RPC: Registered named UNIX socket transport module. [ 0.621589] RPC: Registered udp transport module. [ 0.626355] RPC: Registered tcp transport module. [ 0.631146] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.637768] Unpacking initramfs... [ 0.882800] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.888963] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.895663] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.904978] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.911227] audit: initializing netlink subsys (disabled) [ 0.916709] audit: type=2000 audit(0.900:1): initialized [ 0.922566] Initialise system trusted keyrings [ 0.927229] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.933821] zbud: loaded [ 0.936981] NFS: Registering the id_resolver key type [ 0.942121] Key type id_resolver registered [ 0.946368] Key type id_legacy registered [ 0.950462] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.957215] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.963793] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.971239] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.977857] orangefs_init: module version upstream loaded [ 0.985494] Key type asymmetric registered [ 0.989673] Asymmetric key parser 'x509' registered [ 0.994702] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.002159] io scheduler noop registered [ 1.006147] io scheduler deadline registered [ 1.010506] io scheduler cfq registered (default) [ 1.016195] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.024883] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.031835] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.038167] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.045095] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.051094] PCI: bus0: Fast back to back transfers disabled [ 1.056732] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.064804] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.072991] PCI: bus1: Fast back to back transfers enabled [ 1.078676] PCI: bus2: Fast back to back transfers enabled [ 1.084266] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.089313] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.094837] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.158440] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.166059] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.228418] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.286955] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.294889] console [ttyS0] disabled [ 1.318631] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 12500000) is a 16550A [ 1.327660] console [ttyS0] enabled [ 1.327660] console [ttyS0] enabled [ 1.334761] bootconsole [earlycon0] disabled [ 1.334761] bootconsole [earlycon0] disabled [ 1.364144] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 12500000) is a 16550A [ 1.374164] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.383273] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.392957] scsi host0: ahci-mvebu [ 1.396699] scsi host1: ahci-mvebu [ 1.400362] ata1: FORCE: PHY spd limit set to 3.0Gbps [ 1.405437] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.413400] ata2: FORCE: PHY spd limit set to 3.0Gbps [ 1.418485] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.426981] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.434894] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 1.441291] nand: Hynix H27U2G8F2CTR-BC [ 1.445144] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.452759] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.459962] Bad block table found at page 131008, version 0x01 [ 1.466162] Bad block table found at page 130944, version 0x01 [ 1.472270] 8 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.478404] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 1.483828] 0x000000000000-0x000000500000 : "U-Boot" [ 1.499655] 0x000000500000-0x000000a00000 : "uImage" [ 1.505373] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 1.521260] 0x000000f00000-0x00000c800000 : "image.cfs" [ 1.538011] 0x00000c800000-0x00000d700000 : "rescue fw" [ 1.554007] 0x00000d700000-0x00000eb00000 : "config" [ 1.569788] 0x00000eb00000-0x00000f500000 : "reserve1" [ 1.585712] 0x00000f500000-0x00000ff00000 : "reserve2" [ 1.602260] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.609078] libphy: Fixed MDIO Bus: probed [ 1.613498] libphy: mdio_driver_register: mv88e6085 [ 1.618598] libphy: orion_mdio_bus: probed [ 1.627575] mvneta f1034000.ethernet eth0: Using random mac address f6:01:60:d3:a9:77 [ 1.635652] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.642236] ehci-pci: EHCI PCI platform driver [ 1.646744] ehci-orion: EHCI orion driver [ 1.651094] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.656445] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 1.664058] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.672671] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000 [ 1.678569] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.685388] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.692653] usb usb1: Product: xHCI Host Controller [ 1.697553] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.704030] usb usb1: SerialNumber: f10f0000.usb3 [ 1.709152] hub 1-0:1.0: USB hub found [ 1.712938] hub 1-0:1.0: 1 port detected [ 1.717071] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.722430] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.730015] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.738223] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.745041] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.749271] ata1: SATA link down (SStatus 0 SControl 320) [ 1.757744] usb usb2: Product: xHCI Host Controller [ 1.759191] ata2: SATA link down (SStatus 0 SControl 320) [ 1.768079] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.774548] usb usb2: SerialNumber: f10f0000.usb3 [ 1.779636] hub 2-0:1.0: USB hub found [ 1.783421] hub 2-0:1.0: 1 port detected [ 1.787639] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.793002] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 1.800597] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.809198] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000 [ 1.815063] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.822019] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.829293] usb usb3: Product: xHCI Host Controller [ 1.834192] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.840671] usb usb3: SerialNumber: f10f8000.usb3 [ 1.845735] hub 3-0:1.0: USB hub found [ 1.849532] hub 3-0:1.0: 1 port detected [ 1.853671] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.859026] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.866594] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.874797] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.881631] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.888964] usb usb4: Product: xHCI Host Controller [ 1.893865] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.900344] usb usb4: SerialNumber: f10f8000.usb3 [ 1.905412] hub 4-0:1.0: USB hub found [ 1.909208] hub 4-0:1.0: 1 port detected [ 1.913442] usbcore: registered new interface driver usblp [ 1.919043] usbcore: registered new interface driver usb-storage [ 1.925268] mousedev: PS/2 mouse device common for all mice [ 1.931488] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 1.939383] i2c /dev entries driver [ 1.954835] orion_wdt: Initial timeout 171 sec [ 1.961283] marvell-cesa f1090000.crypto: CESA device successfully registered [ 1.968660] hidraw: raw HID events driver (C) Jiri Kosina [ 1.974412] usbcore: registered new interface driver usbhid [ 1.980025] usbhid: USB HID core driver [ 1.984037] drop_monitor: Initializing network drop monitor service [ 1.990388] Netfilter messages via NETLINK v0.30. [ 1.995126] ip_set: protocol 6 [ 1.998455] NET: Registered protocol family 10 [ 2.003494] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.010485] NET: Registered protocol family 17 [ 2.015110] 8021q: 802.1Q VLAN Support v1.8 [ 2.019443] Key type dns_resolver registered [ 2.023881] ThumbEE CPU extension supported. [ 2.028187] Registering SWP/SWPB emulation handler [ 2.033517] registered taskstats version 1 [ 2.037634] Loading compiled-in X.509 certificates [ 2.042494] zswap: loaded using pool lzo/zbud [ 2.095389] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 2.105853] Key type big_key registered [ 2.113530] Key type encrypted registered [ 2.118676] armada38x-rtc f10a3800.rtc: setting system clock to 2017-07-18 22:18:33 UTC (1500416313) [ 2.129067] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.172194] systemd-udevd[1315]: starting version 215 [ 2.178402] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.270290] usb 1-1: New USB device found, idVendor=090c, idProduct=1000 [ 2.277029] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.284725] usb 1-1: Product: POLLEX 8G [ 2.288603] usb 1-1: Manufacturer: SRT [ 2.292371] usb 1-1: SerialNumber: 033113111111135234000373 [ 2.298504] usb-storage 1-1:1.0: USB Mass Storage device detected [ 2.318122] scsi host2: usb-storage 1-1:1.0 [ 2.457327] usbcore: registered new interface driver uas [ 3.368687] scsi 2:0:0:0: Direct-Access SRT POLLEX 8G 1100 PQ: 0 ANSI: 4 [ 3.380074] sd 2:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) [ 3.387747] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 3.393199] sd 2:0:0:0: [sda] Write Protect is off [ 3.399006] sd 2:0:0:0: [sda] No Caching mode page found [ 3.404344] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 3.413494] sda: sda1 [ 3.421131] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 3.458324] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.573485] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.600934] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 18.470003] systemd-udevd[1520]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 19.211335] EXT4-fs (sda1): re-mounted. Opts: (null) [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 20.388720] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/f6:01:60:d3:a9:77 Sending on LPF/eth0/f6:01:60:d3:a9:77 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 [ 24.568425] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 24.576310] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPOFFER from 192.168.2.1 DHCPACK from 192.168.2.1 bound to 192.168.2.129 -- renewal in 41200 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2449 (syslogd) . ok [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting NTP server: ntpd. [ ok ] Starting system message bus: dbus. [ 36.523210] random: crng init done [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2448 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login: root Password: Last login: Tue Jul 18 14:56:02 PDT 2017 on ttyS0 Linux debian 4.9.0-mvebu-tld-12 #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian 192.168.2.129 Western Digital MyCloud EX2 Ultra Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 15:19:29 up 0 min, 1 user, load average: 0.35, 0.09, 0.03 root@debian:~#
mcmg2
Re: My Cloud Mirror Gen2 July 18, 2017 08:35PM |
setenv set_bootargs_stock 'setenv bootargs root=/dev/ram console=ttyS0,115200' setenv bootcmd_stock 'echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000' setenv bootdev 'usb' setenv device '0:1' setenv load_image_addr '0x02000000' setenv load_initrd_addr '0x2900000' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2)' setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' setenv bootcmd_custom 'if run bootcmd_usb; then ; fi; run bootcmd_stock; reset'
mcmg2
Re: My Cloud Mirror Gen2 July 18, 2017 09:39PM |
setenv set_bootargs_stock 'setenv bootargs root=/dev/ram console=ttyS0,115200' setenv bootcmd_stock 'echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000' setenv bootdev 'usb' setenv device '0:1' setenv load_image_addr '0x02000000' setenv load_initrd_addr '0x2900000' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2)' setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' setenv bootcmd_custom 'if run bootcmd_usb; then ; fi; run bootcmd_stock; reset' setenv bootcmd 'run bootcmd_usb; run bootcmd_stock; reset'
mcmg2
Re: My Cloud Mirror Gen2 July 18, 2017 09:43PM |
Re: My Cloud Mirror Gen2 July 18, 2017 11:30PM |
Admin Registered: 13 years ago Posts: 18,821 |
setenv bootcmd_custom 'if run bootcmd_usb; then ; fi; run bootcmd_stock; reset'
mcmg2
Re: My Cloud Mirror Gen2 July 18, 2017 11:52PM |
| \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-g7c1da33-dirty_v1.04 (Jul 17 2017 - 18:43:06) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fece000:0x1ff96010 BSS: 0x1ffef654 Stack: 0x1f9cdf20 Heap: 0x1f9ce000:0x1fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=run bootcmd_usb; run bootcmd_stock; reset bootcmd_auto=stage_boot $boot_order bootcmd_custom=if run bootcmd_usb; then ; fi; run bootcmd_stock; reset bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock=echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_usb=echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:20:21:3e eth1mtu=1500 eth2addr=00:50:43:20:f2:3e eth2mtu=1500 eth3addr=00:50:43:21:f2:20 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:f2:21:3e ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:3e:f2:20 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 set_bootargs_stock=setenv bootargs root=/dev/ram console=ttyS0,115200 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4304/524284 bytes Marvell>> setenv bootcmd_custom Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=run bootcmd_usb; run bootcmd_stock; reset bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock=echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_usb=echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:20:21:3e eth1mtu=1500 eth2addr=00:50:43:20:f2:3e eth2mtu=1500 eth3addr=00:50:43:21:f2:20 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:f2:21:3e ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:3e:f2:20 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 set_bootargs_stock=setenv bootargs root=/dev/ram console=ttyS0,115200 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4231/524284 bytes Marvell>> saveenv Saving Environment to NAND... Erasing Nand... Writing to Nand... done Marvell>> boot Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3920526 bytes read in 423 ms (8.8 MiB/s) loading uInitrd ... 6210503 bytes read in 498 ms (11.9 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-07-09 9:45:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3920462 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Western Digital MyCloud EX2 Ultra [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/printk/printk.c:2612 register_console+0x3c/0x398 [ 0.000000] console 'earlycon0' already registered [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.9.0-mvebu-tld-12 #2 [ 0.000000] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000] [<c01160bc>] (unwind_backtrace) from [<c0110bb4>] (show_stack+0x10/0x14) [ 0.000000] [<c0110bb4>] (show_stack) from [<c04ba5a4>] (dump_stack+0x70/0x8c) [ 0.000000] [<c04ba5a4>] (dump_stack) from [<c0123ce0>] (__warn+0xc8/0xfc) [ 0.000000] [<c0123ce0>] (__warn) from [<c0123d48>] (warn_slowpath_fmt+0x34/0x44) [ 0.000000] [<c0123d48>] (warn_slowpath_fmt) from [<c0171b1c>] (register_console+0x3c/0x398) [ 0.000000] [<c0171b1c>] (register_console) from [<c0c04dc0>] (setup_early_printk+0x14/0x24) [ 0.000000] [<c0c04dc0>] (setup_early_printk) from [<c0c00478>] (do_early_param+0x6c/0xbc) [ 0.000000] [<c0c00478>] (do_early_param) from [<c013f774>] (parse_args+0x2dc/0x40c) [ 0.000000] [<c013f774>] (parse_args) from [<c0c0088c>] (parse_early_options+0x2c/0x3c) [ 0.000000] [<c0c0088c>] (parse_early_options) from [<c0c008c8>] (parse_early_param+0x2c/0x44) [ 0.000000] [<c0c008c8>] (parse_early_param) from [<c0c03350>] (setup_arch+0x4fc/0xa24) [ 0.000000] [<c0c03350>] (setup_arch) from [<c0c00934>] (start_kernel+0x50/0x390) [ 0.000000] [<c0c00934>] (start_kernel) from [<0000807c>] (0x807c) [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @dfbcc000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 libata.force=3.0G root=LABEL=rootfs earlyprintk console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 500128K/524288K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 24160K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000004] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007883] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019112] Console: colour dummy device 80x30 [ 0.023627] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.034035] pid_max: default: 32768 minimum: 301 [ 0.038803] Security Framework initialized [ 0.043004] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.049679] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.057252] CPU: Testing write buffer coherency: ok [ 0.062343] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.068086] Setting up static identity map for 0x100000 - 0x100058 [ 0.074517] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.079802] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283603] Booting CPU 1 [ 0.286473] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286531] Brought up 2 CPUs [ 0.295291] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301612] CPU: All CPU(s) started in SVC mode. [ 0.306849] devtmpfs: initialized [ 0.312766] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320751] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330691] prandom: seed boundary self test passed [ 0.337654] prandom: 100 self tests passed [ 0.341815] pinctrl core: initialized pinctrl subsystem [ 0.347851] NET: Registered protocol family 16 [ 0.353035] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.383454] cpuidle: using governor ladder [ 0.413421] cpuidle: using governor menu [ 0.417553] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.425626] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.474480] vgaarb: loaded [ 0.477534] SCSI subsystem initialized [ 0.481836] usbcore: registered new interface driver usbfs [ 0.487493] usbcore: registered new interface driver hub [ 0.492929] usbcore: registered new device driver usb [ 0.498303] media: Linux media interface: v0.10 [ 0.502949] Linux video capture interface: v2.00 [ 0.508648] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.544868] VFS: Disk quotas dquot_6.6.0 [ 0.548939] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.564233] NET: Registered protocol family 2 [ 0.569100] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.576222] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.582767] TCP: Hash tables configured (established 4096 bind 4096) [ 0.589213] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.595113] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.601546] NET: Registered protocol family 1 [ 0.606233] RPC: Registered named UNIX socket transport module. [ 0.612230] RPC: Registered udp transport module. [ 0.616996] RPC: Registered tcp transport module. [ 0.621771] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.628393] Unpacking initramfs... [ 0.872764] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.878910] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.885608] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.894923] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.901163] audit: initializing netlink subsys (disabled) [ 0.906645] audit: type=2000 audit(0.890:1): initialized [ 0.912495] Initialise system trusted keyrings [ 0.917155] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.923742] zbud: loaded [ 0.926902] NFS: Registering the id_resolver key type [ 0.932046] Key type id_resolver registered [ 0.936293] Key type id_legacy registered [ 0.940387] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.947140] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.953714] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.961160] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.967778] orangefs_init: module version upstream loaded [ 0.975433] Key type asymmetric registered [ 0.979612] Asymmetric key parser 'x509' registered [ 0.984641] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.992099] io scheduler noop registered [ 0.996087] io scheduler deadline registered [ 1.000448] io scheduler cfq registered (default) [ 1.006141] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.014825] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.021776] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.028099] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.035036] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.041035] PCI: bus0: Fast back to back transfers disabled [ 1.046673] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.054745] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.062932] PCI: bus1: Fast back to back transfers enabled [ 1.068604] PCI: bus2: Fast back to back transfers enabled [ 1.074208] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.079250] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.084772] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.149139] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.156763] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.219117] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.278049] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.285958] console [ttyS0] disabled [ 1.309712] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 12500000) is a 16550A [ 1.318749] console [ttyS0] enabled [ 1.318749] console [ttyS0] enabled [ 1.325839] bootconsole [earlycon0] disabled [ 1.325839] bootconsole [earlycon0] disabled [ 1.355228] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 12500000) is a 16550A [ 1.365252] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.374362] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.384067] scsi host0: ahci-mvebu [ 1.387790] scsi host1: ahci-mvebu [ 1.391451] ata1: FORCE: PHY spd limit set to 3.0Gbps [ 1.396527] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.404492] ata2: FORCE: PHY spd limit set to 3.0Gbps [ 1.409574] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.418067] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.425967] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 1.432362] nand: Hynix H27U2G8F2CTR-BC [ 1.436215] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.443830] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.451032] Bad block table found at page 131008, version 0x01 [ 1.457232] Bad block table found at page 130944, version 0x01 [ 1.463341] 8 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.469472] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 1.474897] 0x000000000000-0x000000500000 : "U-Boot" [ 1.480732] 0x000000500000-0x000000a00000 : "uImage" [ 1.496457] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 1.512350] 0x000000f00000-0x00000c800000 : "image.cfs" [ 1.529107] 0x00000c800000-0x00000d700000 : "rescue fw" [ 1.545107] 0x00000d700000-0x00000eb00000 : "config" [ 1.560899] 0x00000eb00000-0x00000f500000 : "reserve1" [ 1.576822] 0x00000f500000-0x00000ff00000 : "reserve2" [ 1.593354] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.600167] libphy: Fixed MDIO Bus: probed [ 1.604594] libphy: mdio_driver_register: mv88e6085 [ 1.609752] libphy: orion_mdio_bus: probed [ 1.618846] mvneta f1034000.ethernet eth0: Using random mac address e2:80:f9:4c:4a:13 [ 1.626899] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.633480] ehci-pci: EHCI PCI platform driver [ 1.637987] ehci-orion: EHCI orion driver [ 1.642324] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.647673] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 1.655286] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.663891] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000 [ 1.669794] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.676614] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.683881] usb usb1: Product: xHCI Host Controller [ 1.688789] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.695258] usb usb1: SerialNumber: f10f0000.usb3 [ 1.700373] hub 1-0:1.0: USB hub found [ 1.704160] hub 1-0:1.0: 1 port detected [ 1.708294] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.713652] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.721240] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.729444] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.736264] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.739943] ata1: SATA link down (SStatus 0 SControl 320) [ 1.748975] usb usb2: Product: xHCI Host Controller [ 1.753874] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.759889] ata2: SATA link down (SStatus 0 SControl 320) [ 1.765770] usb usb2: SerialNumber: f10f0000.usb3 [ 1.770860] hub 2-0:1.0: USB hub found [ 1.774644] hub 2-0:1.0: 1 port detected [ 1.778879] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.784225] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 1.791824] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.800441] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000 [ 1.806304] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.813182] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.820447] usb usb3: Product: xHCI Host Controller [ 1.825347] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.831823] usb usb3: SerialNumber: f10f8000.usb3 [ 1.836893] hub 3-0:1.0: USB hub found [ 1.840691] hub 3-0:1.0: 1 port detected [ 1.844826] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.850179] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.857745] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.865947] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.872779] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.880042] usb usb4: Product: xHCI Host Controller [ 1.884941] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.891487] usb usb4: SerialNumber: f10f8000.usb3 [ 1.896551] hub 4-0:1.0: USB hub found [ 1.900348] hub 4-0:1.0: 1 port detected [ 1.904580] usbcore: registered new interface driver usblp [ 1.910177] usbcore: registered new interface driver usb-storage [ 1.916402] mousedev: PS/2 mouse device common for all mice [ 1.922610] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 1.930427] i2c /dev entries driver [ 1.945899] orion_wdt: Initial timeout 171 sec [ 1.952350] marvell-cesa f1090000.crypto: CESA device successfully registered [ 1.959728] hidraw: raw HID events driver (C) Jiri Kosina [ 1.965481] usbcore: registered new interface driver usbhid [ 1.971093] usbhid: USB HID core driver [ 1.975110] drop_monitor: Initializing network drop monitor service [ 1.981459] Netfilter messages via NETLINK v0.30. [ 1.986197] ip_set: protocol 6 [ 1.989528] NET: Registered protocol family 10 [ 1.994569] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.001544] NET: Registered protocol family 17 [ 2.006176] 8021q: 802.1Q VLAN Support v1.8 [ 2.010510] Key type dns_resolver registered [ 2.014947] ThumbEE CPU extension supported. [ 2.019254] Registering SWP/SWPB emulation handler [ 2.024582] registered taskstats version 1 [ 2.028713] Loading compiled-in X.509 certificates [ 2.033560] zswap: loaded using pool lzo/zbud [ 2.086664] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 2.097189] Key type big_key registered [ 2.104814] Key type encrypted registered [ 2.109956] armada38x-rtc f10a3800.rtc: setting system clock to 2017-07-19 04:41:51 UTC (1500439311) [ 2.120348] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.163310] systemd-udevd[1315]: starting version 215 [ 2.170009] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.261007] usb 1-1: New USB device found, idVendor=090c, idProduct=1000 [ 2.267746] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.275091] usb 1-1: Product: POLLEX 8G [ 2.285513] usb 1-1: Manufacturer: SRT [ 2.289323] usb 1-1: SerialNumber: 033113111111135234000373 [ 2.302834] usb-storage 1-1:1.0: USB Mass Storage device detected [ 2.317110] scsi host2: usb-storage 1-1:1.0 [ 2.451739] usbcore: registered new interface driver uas [ 3.369385] scsi 2:0:0:0: Direct-Access SRT POLLEX 8G 1100 PQ: 0 ANSI: 4 [ 3.380540] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 3.385903] sd 2:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) [ 3.395221] sd 2:0:0:0: [sda] Write Protect is off [ 3.400747] sd 2:0:0:0: [sda] No Caching mode page found [ 3.406084] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 3.415468] sda: sda1 [ 3.424420] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 3.465402] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.584191] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.592845] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 17.599766] EXT4-fs (sda1): write access will be enabled during recovery [ 38.183491] random: crng init done [ 52.663227] EXT4-fs (sda1): orphan cleanup on readonly fs [ 52.672862] EXT4-fs (sda1): 1 orphan inode deleted [ 52.677676] EXT4-fs (sda1): recovery complete [ 54.111671] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 54.395929] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR) [ 54.409485] systemd[1]: Detected architecture 'arm'. Welcome to Debian GNU/Linux 8 (jessie)! [ 54.459813] systemd[1]: Set hostname to <debian>. [ 54.776489] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory. [ 54.793107] systemd[1]: Starting Forward Password Requests to Wall Directory Watch. [ 54.801058] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 54.808731] systemd[1]: Expecting device dev-ttyS0.device... Expecting device dev-ttyS0.device... [ 54.838721] systemd[1]: Starting Remote File Systems (Pre). [ OK ] Reached target Remote File Systems (Pre). [ 54.878696] systemd[1]: Reached target Remote File Systems (Pre). [ 54.884909] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point. [ OK ] Set up automount Arbitrary Executable File Formats F...utomount Point. [ OK ] Reached target Swap. [ OK ] Created slice Root Slice. [ OK ] Created slice User and Session Slice. [ OK ] Listening on Delayed Shutdown Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on LVM2 metadata daemon socket. [ OK ] Listening on Device-mapper event daemon FIFOs. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on Journal Socket. [ OK ] Created slice System Slice. [ OK ] Created slice system-getty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. Starting Increase datagram queue length... Starting Nameserver information manager... Mounting Debug File System... Starting Create list of required static device nodes...rrent kernel... Starting udev Coldplug all Devices... Starting Load Kernel Modules... Mounting POSIX Message Queue File System... Starting Remount Root and Kernel File Systems... [ OK [ 55.640725] fuse init (API version 7.26) ] Reached target Slices. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Started Increase datagram queue length. [ OK ] Started Create list of required static device nodes ...current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Nameserver information manager. [ OK ] Started udev Coldplug all Devices. Starting udev Wait for Complete Device Initialization... Starting Initial Check File System Quotas... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Mounting FUSE Control File System... Starting Create Static Device Nodes in /dev... [ OK ] Listening on Syslog Socket. Starting Journal Service... [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [FAILED] Failed to start Load/Save Random Seed. See 'systemctl status systemd-random-seed.service' for details. [ OK ] Started Apply Kernel Variables. [FAILED] Failed to start Initial Check File System Quotas. See 'systemctl status quota.service' for details. [ OK ] Started Create Static Device Nodes in /dev. [ 56.477365] quota-initial-check.sh[1424]: Checking quotas...done. [ 56.531107] quota-initial-check.sh[1424]: rm: cannot remove ‘/var/lib/quota/new’: Read-only file system Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ 56.614812] systemd-udevd[1441]: starting version 215 Mounting /tmp... [ OK ] Started udev Kernel Device Manager. [ OK ] Mounted /tmp. Starting LSB: Tune IDE hard disks... Starting LSB: MD array assembly... [ OK ] Started LSB: Tune IDE hard disks. [ OK ] Found device /dev/ttyS0. [ OK ] Started LSB: MD array assembly. [ OK ] Started udev Wait for Complete Device Initialization. Starting Activation of LVM2 logical volumes... Starting Copy rules generated while the root was ro... [ OK ] Started Copy rules generated while the root was ro. [ OK ] Started Activation of LVM2 logical volumes. [ OK ] Reached target Encrypted Volumes. Starting Activation of LVM2 logical volumes... [ OK ] Started Activation of LVM2 logical volumes. Starting Monitoring of LVM2 mirrors, snapshots etc. ...ress polling... [ OK ] Started Monitoring of LVM2 mirrors, snapshots etc. u...ogress polling. [ OK ] Reached target Local File Systems. Starting Cleanup PHP session files... Starting Cleanup monit state file... Starting Create Volatile Files and Directories... [ OK ] Reached target Remote File Systems. Starting Trigger Flushing of Journal to Persistent Storage... Starting LSB: Raise network interfaces.... [ OK ] Started Cleanup PHP session files. [FAILED] Failed to start Cleanup monit state file. See 'systemctl status openmediavault-cleanup-monit.service' for details. [ OK ] Started Create Volatile Files and Directories. [ 58.227931] systemd-journald[1435]: Received request to flush runtime journal from PID 1 Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Trigger Flushing of Journal to Persistent Storage. [FAILED] Failed to start Update UTMP about System Boot/Shutdown. See 'systemctl status systemd-update-utmp.service' for details. [DEPEND] Dependency failed for Update UTMP about System Runlevel Changes. [ 62.729122] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ OK ] Started LSB: Raise network interfaces.. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting LSB: RPC portmapper replacement... [ OK ] Started LSB: RPC portmapper replacement. [ OK ] Reached target RPC Port Mapper. Starting LSB: NFS support files common to client and server... [ OK ] Started LSB: NFS support files common to client and server. [ OK ] Reached target System Initialization. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on ACPID Listen Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Timers. [ OK ] Reached target Paths. [ OK ] Reached target Basic System. Starting The OpenMediaVault engine daemon that proce... RPC request... Starting A high performance web server and a reverse proxy server... Starting Run anacron jobs... [ OK ] Started Run anacron jobs. Starting Self Monitoring and Reporting Technology (SMART) Daemon... [ OK ] Started Self Monitoring and Reporting Technology (SMART) Daemon. Starting The PHP FastCGI Process Manager... Starting Regular background program processing daemon... [ OK ] Started Regular background program processing daemon. Starting RPC Remote Quota Server... Starting OpenBSD Secure Shell server... [ OK ] Started OpenBSD Secure Shell server. Starting /etc/rc.local Compatibility... Starting Login Service... Starting LSB: Start NTP daemon... Starting LSB: start the RRDtool data caching daemon... Starting LSB: SNMP agents... Starting LSB: start Samba daemons for the AD DC... Starting LSB: service and resource monitoring daemon... Starting LSB: Load kernel modules needed to enable cpufreq scaling... Starting LSB: Postfix Mail Transport Agent... Starting LSB: Kernel NFS server support... Starting LSB: start Samba NetBIOS nameserver (nmbd)... Starting LSB: Starts syslogd... Starting LSB: Starts ProFTPD daemon... Starting Avahi mDNS/DNS-SD Stack... Starting D-Bus System Message Bus... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Avahi mDNS/DNS-SD Stack. Starting System Logging Service... Starting Permit User Sessions... Starting ACPI event daemon... [ OK ] Started ACPI event daemon. [ OK ] Started RPC Remote Quota Server. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started LSB: Start NTP daemon. [FAILED] Failed to start LSB: start the RRDtool data caching daemon. See 'systemctl status rrdcached.service' for details. [ OK ] Started LSB: service and resource monitoring daemon. [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling. [ OK ] Started LSB: Postfix Mail Transport Agent. [FAILED] Failed to start A high performance web server and a ...e proxy server. See 'systemctl status nginx.service' for details. [ OK ] Started LSB: Kernel NFS server support. [ OK ] Started LSB: Starts syslogd. [ OK ] Started Permit User Sessions. [ OK ] Started The OpenMediaVault engine daemon that proces...he RPC request. [ OK ] Started System Logging Service. [FAILED] Failed to start LSB: Starts ProFTPD daemon. See 'systemctl status proftpd.service' for details. [ OK ] Started Login Service. Mounting Arbitrary Executable File Formats File System... Starting LSB: Starts klogd... [ OK ] Reached target Mail Transport Agent. Starting LSB: set CPUFreq kernel parameters... Starting Getty on tty1... [ OK ] Started Getty on tty1. Starting Serial Getty on ttyS0... [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Mounted Arbitrary Executable File Formats File System. [ OK ] Started LSB: Starts klogd. [ OK ] Started LSB: SNMP agents. [ OK ] Started LSB: set CPUFreq kernel parameters. [FAILED] Failed to start The PHP FastCGI Process Manager. See 'systemctl status php5-fpm.service' for details. Starting LSB: manage the statistics collection daemon... [ OK ] Started LSB: manage the statistics collection daemon. [ OK ] Started LSB: start Samba daemons for the AD DC. [FAILED] Failed to start LSB: start Samba NetBIOS nameserver (nmbd). See 'systemctl status nmbd.service' for details. Starting LSB: start Samba SMB/CIFS daemon (smbd)... [FAILED] Failed to start LSB: start Samba SMB/CIFS daemon (smbd). See 'systemctl status smbd.service' for details. [ OK ] Reached target Multi-User System. Starting Beep after system start... [ OK ] Reached target Graphical Interface. [ OK ] Started Beep after system start. openmediavault 3.0.84 (Erasmus) debian ttyS0 Copyright (C) 2009-2017 by Volker Theile. All rights reserved. To manage the system visit the openmediavault web control panel: No network interface(s) available By default the web control panel administrator account has the username 'admin' and password 'openmediavault'. It is recommended that you change the password for this account within the web control panel or using the 'omv-firstaid' CLI command. For more information regarding this appliance, please visit the web site: http://www.openmediavault.org debian login: root Password: Linux debian 4.9.0-mvebu-tld-12 #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian Western Digital MyCloud EX2 Ultra Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 13:44:09 up 2 min, 1 user, load average: 1.00, 0.37, 0.14 root@debian:~# omv-initsystem /usr/sbin/omv-initsystem: 38: /usr/sbin/omv-initsystem: cannot create /var/log/openmediavault/initsystem.log: Read-only file system root@debian:~# fw_printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=run bootcmd_usb; run bootcmd_stock; reset bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock=echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_usb=echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:20:21:3e eth1mtu=1500 eth2addr=00:50:43:20:f2:3e eth2mtu=1500 eth3addr=00:50:43:21:f2:20 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:f2:21:3e ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:3e:f2:20 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 set_bootargs_stock=setenv bootargs root=/dev/ram console=ttyS0,115200 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 root@debian:~#
mcmg2
Re: My Cloud Mirror Gen2 July 19, 2017 12:04AM |
root@debian:~/mcm-daemon# omv-initsystem /usr/sbin/omv-initsystem: 38: /usr/sbin/omv-initsystem: cannot create /var/log/o penmediavault/initsystem.log: Read-only file system root@debian:~/mcm-daemon# fw_printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$root path ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_para ms clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=run bootcmd_usb; run bootcmd_stock; reset bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv boo targs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip= $ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd. lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandE cc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$boo targs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_ena ble clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $ bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; boo tm 0x2000000; bootcmd_stock=echo Booting from stock ... ; run set_bootargs_stock; printenv boo targs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x50 0000;bootm 0xa00000 0xf00000 bootcmd_usb=echo Booting from USB ...; usb start; setenv fdt_skip_update yes; us b start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:20:21:3e eth1mtu=1500 eth2addr=00:50:43:20:f2:3e eth2mtu=1500 eth3addr=00:50:43:21:f2:20 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:f2:21:3e ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /b oot/uImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_add r /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@1 5m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(r eserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:3e:f2:20 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 set_bootargs_stock=setenv bootargs root=/dev/ram console=ttyS0,115200 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdpa rts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdela y=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(u Ramdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reser ve1),10m@245m(reserve2) vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 root@debian:~/mcm-daemon# htop root@debian:~/mcm-daemon# service samba start Failed to start samba.service: Unit samba.service is masked. root@debian:~/mcm-daemon#
Re: My Cloud Mirror Gen2 July 19, 2017 12:08AM |
Admin Registered: 13 years ago Posts: 18,821 |
Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.584191] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.592845] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 17.599766] EXT4-fs (sda1): write access will be enabled during recovery [ 38.183491] random: crng init done [ 52.663227] EXT4-fs (sda1): orphan cleanup on readonly fs [ 52.672862] EXT4-fs (sda1): 1 orphan inode deleted [ 52.677676] EXT4-fs (sda1): recovery complete [ 54.111671] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
dmesg | tailAnd then
umount /dev/sdb1 e2fsck /dev/sdb1
syncRemove the USB drive and put it back to the Mirror Gen2, power up. Let it boot and post serial console log here.
mcmg2
Re: My Cloud Mirror Gen2 July 19, 2017 12:16AM |
mint kwboot # dmesg | tail [43257.191142] sd 3:0:0:0: Attached scsi generic sg2 type 0 [43257.207627] sd 3:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) [43257.219325] sd 3:0:0:0: [sda] Write Protect is off [43257.219328] sd 3:0:0:0: [sda] Mode Sense: 43 00 00 00 [43257.228379] sd 3:0:0:0: [sda] No Caching mode page found [43257.228385] sd 3:0:0:0: [sda] Assuming drive cache: write through [43257.301754] sda: sda1 [43257.362715] sd 3:0:0:0: [sda] Attached SCSI removable disk [43258.590264] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [43258.653374] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) mint kwboot # umount /dev/sda1 mint kwboot # e2fsck /dev/sda1 e2fsck 1.42.13 (17-May-2015) rootfs: clean, 58649/491520 files, 427405/1965824 blocks mint kwboot # sync mint kwboot #
Re: My Cloud Mirror Gen2 July 19, 2017 01:05AM |
Registered: 7 years ago Posts: 119 |
Quote
mcmg2
why is samba.service masked?
mcmg2
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 02:12AM |
setenv set_bootargs_stock 'setenv bootargs root=/dev/ram console=ttyS0,115200' setenv bootcmd_stock 'echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000' setenv bootdev 'usb' setenv device '0:1' setenv load_image_addr '0x02000000' setenv load_initrd_addr '0x2900000' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2)' setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' setenv bootcmd 'run bootcmd_usb; run bootcmd_stock; reset'
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 02:15AM |
Admin Registered: 13 years ago Posts: 18,821 |
mcmg2
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 07:26AM |
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 07:55AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 03:17PM |
Registered: 7 years ago Posts: 119 |
Quote
bodhi
What you said is extremely interesting! I need you to describe a little more.
mcmg2
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 05:07PM |
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 05:44PM |
Admin Registered: 13 years ago Posts: 18,821 |
./kwboot -f -t -B 115200 /dev/ttyUSB0 -b u-boot-a38x-GrandTeton_2014T3_PQ-nand-uart.bin -s 0 -q 1
http://www.ieeebcit.org/product/pinheader10m/
http://hobbycomponents.com/usb-interface/618-usb-to-rs232-ttl-serial-interface-cable
Quote
> I was trying to kwboot and it happens in less than
> 5 seconds. sometimes it took me more than 1 hours(
> I've watched 2episode of suit season5).
Quote
> I touched cable by mistake(of course, my eyes on drama and h
> ands moving from keyboard to power cable of my clo
> ud mirror) and it gives some gabage letter.
> so I try to move the cable around to see what happ
> ens. and I used finger to give it different angle.
> by experience, 90 degree(like soldered on pcbboard
> ) and hold steady with finger works good. it took
> me less than 5 min try.
mcmg2
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 06:04PM |
Re: My Cloud Mirror Gen2 u-boot July 19, 2017 06:12PM |
Admin Registered: 13 years ago Posts: 18,821 |
mcmg2
Re: My Cloud Mirror Gen2 u-boot November 06, 2018 04:31PM |
cd /media/sdb1/boot cp -a zImage-4.12.4-mvebu-tld-1 zImage.fdt cat dts/armada-385-wd.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.4-mvebu-tld-1 -d zImage.fdt uImage
Re: My Cloud Mirror Gen2 u-boot November 06, 2018 10:12PM |
Admin Registered: 13 years ago Posts: 18,821 |
> cd /media/sdb1/boot > > cp -a zImage-4.12.4-mvebu-tld-1 zImage.fdt > > cat dts/armada-385-wd.dtb >> zImage.fdt > > mkimage -A arm -O linux -T kernel -C none -a > 0x00008000 -e 0x00008000 -n > Linux-4.12.4-mvebu-tld-1 -d zImage.fdt uImage >
mcmg2
Re: My Cloud Mirror Gen2 u-boot June 29, 2020 10:59PM |
Re: My Cloud Mirror Gen2 u-boot March 02, 2024 04:37AM |
Registered: 5 years ago Posts: 50 |
Marvell>> SatR read mvBoardSatRRead: Error: Read from S@R failed Error reading from TWSI