Debian does not boot on Pogoplug V4 September 29, 2017 11:09AM |
Registered: 6 years ago Posts: 3 |
[root@pcke mmc]# tar -xjf ../Downloads/Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 [root@pcke mmc]# cd boot/ [root@pcke boot]# ls config-4.12.1-kirkwood-tld-1 linux-headers-4.12.1-kirkwood-tld-1_1.0_armel.deb uInitrd dts System.map-4.12.1-kirkwood-tld-1 vmlinuz-4.12.1-kirkwood-tld-1 initrd.img-4.12.1-kirkwood-tld-1 uImage zImage-4.12.1-kirkwood-tld-1 [root@pcke boot]# cp zImage-4.12.1-kirkwood-tld-1 zImage.fdt [root@pcke boot]# cat dts/kirkwood-pogoplug_v4.dtb >> zImage.fdt [root@pcke boot]# mv uImage uImage.orig [root@pcke boot]# mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage Image Name: Linux-4.12.1-kirkwood-tld-1 Created: Fri Sep 29 16:38:19 2017 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3831812 Bytes = 3742.00 KiB = 3.65 MiB Load Address: 00008000 Entry Point: 00008000 [root@pcke boot]# sync [root@pcke boot]# cd ../.. [root@pcke bubble]# umount mmc
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 23068672 bda82d74-01 83 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Card did not respond to voltage select! no IDE devices available 3831876 bytes read in 440 ms (8.3 MiB/s) 7245696 bytes read in 455 ms (15.2 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-09-29 14:38:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3831812 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
[root@pcke bubble]# mkfs.ext3 -L rootfs /dev/sdd1 mke2fs 1.43.6 (29-Aug-2017) /dev/sdd1 contains a ext3 file system labelled 'rootfs' last mounted on /home/bubble/mmc on Fri Sep 29 16:36:10 2017 Proceed anyway? (y,N) y Creating filesystem with 2883584 4k blocks and 720896 inodes Filesystem UUID: b99813de-c562-42f0-a3da-9102a2cc9caa Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208 Allocating group tables: done Writing inode tables: done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: done [root@pcke bubble]# mount /dev/sdd1 mmc [root@pcke bubble]# cd mmc [root@pcke mmc]# tar -xjf ../Downloads/Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 [root@pcke mmc]# cat etc/fstab # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> LABEL=rootfs / ext3 noatime,errors=remount-ro 0 1 tmpfs /tmp tmpfs defaults 0 0 [root@pcke mmc]# cd .. [root@pcke bubble]# sync [root@pcke bubble]# umount mmc
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST9500325AS Firm: 0005HPM1 Ser#: S2W9178P Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) no USB devices available Partition Map for IDE device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 23068672 bda82d74-01 83 loading envs from ide 0 ... ** File not found /boot/uEnv.txt ** ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! ** Bad device mmc 0 ** ** Bad device mmc 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST9500325AS Firm: 0005HPM1 Ser#: S2W9178P Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) 3821592 bytes read in 1188 ms (3.1 MiB/s) 7245696 bytes read in 1797 ms (3.8 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_uenv; run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:31:05:39:9C if_netconsole=ping $serverip ipaddr=172.17.17.27 led_error=orange blinking led_exit=green off led_init=green blinking machid=f78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) ncip=172.17.17.2 partition=nand0,2 preboot=run if_netconsole start_netconsole preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=172.17.17.2 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1
Re: Debian does not boot on Pogoplug V4 September 29, 2017 04:50PM |
Admin Registered: 13 years ago Posts: 18,560 |
Quote
8. Flashing default u-boot envs image:
As described in step 1, u-boot envs must be defined in etc/fw_env.config as
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd0 0xc0000 0x20000 0x20000
A special section (B. Flashing default u-boot envs image) about flashing default u-boot envs is included at the end of this installation procedure. Please follow the instruction in this section B to perform this step before continuing with step 9.
Re: Debian does not boot on Pogoplug V4 October 01, 2017 04:39AM |
Registered: 6 years ago Posts: 3 |
Re: Debian does not boot on Pogoplug V4 October 01, 2017 07:18AM |
Registered: 6 years ago Posts: 3 |
Re: Debian does not boot on Pogoplug V4 October 01, 2017 01:45PM |
Admin Registered: 13 years ago Posts: 18,560 |
Re: Debian does not boot on Pogoplug V4 December 28, 2017 10:42PM |
Registered: 6 years ago Posts: 5 |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> ptintenv Unknown command 'ptintenv' - try 'help' Pogov4> printenv arcNumber=3960 baudrate=115200 bootargs=console=ttyS0,115200 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) bootargs_lede= bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; run bootcmd_pogo; reset bootcmd_exec=if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi bootcmd_lede=run set_bootargs_lede; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 \ uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 bootzubi=echo Booting from nand ...; run setargsubi; bootz ${loadaddr} - ${fdt_addr}; device=0:1 ethact=egiga0 ethaddr=00:25:31:05:c6:4a fdt_addr=0x1c00000 fdt_file=/boot/kirkwood-pogoplug_v4.dtb if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking loadaddr=0x800000 loadubi=echo Trying to boot from NAND ...;if run mountubi; then run loadubizimage;run loadubifdt;ubifsumount;run bootzubi;fi loadubifdt=ubifsload ${fdt_addr} ${fdt_file} loadubizimage=ubifsload ${loadaddr} ${zimage} machid=F78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc 0:1 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mountubi=ubi part rootfs; ubifsmount ubi0:rootfs mtddevname=u-boot mtddevnum=0 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,0 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.0.220 set_bootargs_lede=setenv bootargs console=ttyS0,115200 $mtdparts set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts setargsubi=setenv bootargs console=${console},${baudrate} ${optargs} ubi.mtd=1 root=ubi0:rootfs rw rootfstype=ubifs rootwait ${mtdparts} start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb 0:1 0x800000 /uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 usb_rootfstype=ext3 zimage=/boot/zImage Environment size: 3616/131068 bytes Pogov4> boot (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! MMC rescan: current device # 0 initialized OK 2875692 bytes read in 1597 ms (1.7 MiB/s) 6535284 bytes read in 2175 ms (2.9 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.18.5-kirkwood-tld-1 Created: 2015-11-11 5:03:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2875628 Bytes = 2.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.18.5-kirkwood-tld-1 Created: 2015-02-19 1:49:36 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6535220 Bytes = 6.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel.
Re: Debian does not boot on Pogoplug V4 December 28, 2017 11:20PM |
Admin Registered: 13 years ago Posts: 18,560 |
printenv
Re: Debian does not boot on Pogoplug V4 December 29, 2017 08:03AM |
Registered: 6 years ago Posts: 5 |
Re: Debian does not boot on Pogoplug V4 December 29, 2017 01:44PM |
Registered: 6 years ago Posts: 5 |
Re: Debian does not boot on Pogoplug V4 December 29, 2017 01:46PM |
Admin Registered: 13 years ago Posts: 18,560 |
Re: Debian does not boot on Pogoplug V4 December 29, 2017 05:01PM |
Registered: 6 years ago Posts: 5 |
Re: Debian does not boot on Pogoplug V4 December 30, 2017 12:04AM |
Admin Registered: 13 years ago Posts: 18,560 |
> U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) > Pogoplug V4
> Uncompressing Linux... done, booting the kernel.
Re: Debian does not boot on Pogoplug V4 December 30, 2017 07:23PM |
Registered: 6 years ago Posts: 5 |
Re: Debian does not boot on Pogoplug V4 December 30, 2017 09:24PM |
Admin Registered: 13 years ago Posts: 18,560 |
> Uncompressing Linux... done, booting the kernel.was most likely because of your uImage, and/or the lack of DTB loading.
juandbotiva
Re: Debian does not boot on Pogoplug V4 August 06, 2018 07:35PM |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed no USB devices available no IDE devices available running scan_disk ... Scan device usb (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found device usb 0:1 Unknown command 'load' - try 'help' device usb 1:1 Unknown command 'load' - try 'help' device usb 2:1 Unknown command 'load' - try 'help' device usb 3:1 Unknown command 'load' - try 'help' Scan device ide Reset IDE: ide_preinit failed device ide 0:1 Unknown command 'load' - try 'help' device ide 1:1 Unknown command 'load' - try 'help' device ide 2:1 Unknown command 'load' - try 'help' device ide 3:1 Unknown command 'load' - try 'help' Scan device mmc device mmc 0:1 Unknown command 'load' - try 'help' device mmc 1:1 Unknown command 'load' - try 'help' device mmc 2:1 Unknown command 'load' - try 'help' device mmc 3:1 Unknown command 'load' - try 'help' loading uImage ... Unknown command 'load' - try 'help' loading uInitrd ... Unknown command 'load' - try 'help' loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ... Unknown command 'load' - try 'help' Wrong Image Format for bootm command ERROR: can't get kernel image!
Pogov4> printenv arcNumber=3960 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_usb=usb start ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3130/131068 bytes
Re: Debian does not boot on Pogoplug V4 August 07, 2018 12:49AM |
Admin Registered: 13 years ago Posts: 18,560 |
Unknown command 'load' - try 'help'
juandbotiva
Re: Debian does not boot on Pogoplug V4 August 08, 2018 11:13AM |
Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000831). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
Using machid 0xffffffff from environment Starting kernel ... Uncompressing Linux... done, booting the kernel.
Re: Debian does not boot on Pogoplug V4 August 08, 2018 12:22PM |
Admin Registered: 13 years ago Posts: 18,560 |
Pogov4> printenv
juandbotiva
Re: Debian does not boot on Pogoplug V4 August 08, 2018 01:14PM |
Pogov4> printenv arcNumber=2097 baudrate=115200 bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 filesize=a1a if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=ffffffff mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_ready_retry=15 usb_root=/dev/sda1 Environment size: 4406/131068 bytes
Re: Debian does not boot on Pogoplug V4 August 09, 2018 12:29AM |
Admin Registered: 13 years ago Posts: 18,560 |
cp -a uboot.2014.07-tld-3.environment.scr /media/sdb1/boot/ sync
usb start ext2load usb 0:1 0x800000 /boot/uboot.2014.07-tld-3.environment.scr source 0x800000
setenv load_dtb 'ext2load $bootdev $device 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb'
boot
usb start ext2load usb 0:1 0x800000 /boot/uboot.2014.07-tld-3.environment.scr source 0x800000 setenv load_dtb 'ext2load $bootdev $device 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb' saveenv boot
juandbotiva
Re: Debian does not boot on Pogoplug V4 August 09, 2018 10:15AM |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> ext2load mmc 0:1 0x800000 /boot/uboot.2014.07-tld-3.environment.scr 2822 bytes read in 1110 ms (2 KiB/s) Pogov4> source 0x800000 ## Executing script at 00800000 Pogov4> setenv load_dtb 'ext2load $bootdev $device 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb' Pogov4> printenv arcNumber=2097 baudrate=115200 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=mw 0x800000 0 1;run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 filesize=b06 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=ext2load $bootdev $device 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb load_dtb_addr=0x1c00000 load_initrd=ext2load $bootdev $device 0x1100000 /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=ext2load $bootdev $device 0x800000 /boot/uImage load_uimage_addr=0x800000 machid=0x831 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 scan_disk=scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 0x800000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=$console root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t 0x810000 uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_ready_retry=15 usb_root=/dev/sda1 Envir Pogovext2lo2load mmc 0:1 0x800000 /boot/uboot.2014.07-tld-3.environment.scr Unknown command 'ext2lo' - try 'help' Pogov4> ext2l ext2load ext2ls Pogov4> ext2l ext2load ext2ls Pogov4> ext2load ext2load - load binary file from a Ext2 filesystem Usage: ext2load <interface> <dev[:part]> [addr] [filename] [bytes] - load binary file 'filename' from 'dev' on 'interface' to address 'addr' from ext2 filesystem. Pogov4> setenv bootdev mmc Pogov4> boot (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK no USB devices available no IDE devices available Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 63 30876867 00000000-01 83 loading envs from mmc 0 ... Unknown command 'load' - try 'help' Scan device usb (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device size - ide 0 ** device ide 1:1 ** Bad device size - ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 997 ms (0 Bytes/s) Found bootable drive on mmc 0 10284 bytes read in 2435 ms (3.9 KiB/s) 3821592 bytes read in 1406 ms (2.6 MiB/s) 7245696 bytes read in 1620 ms (4.3 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0742f000, end 07b17f40 ... OK Loading Device Tree to 07429000, end 0742e82b ... OK Using machid 0x831 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Pogoplug v4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 109428K/131072K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 21644K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000066] Switching to timer-based delay loop, resolution 6ns [ 0.000767] Console: colour dummy device 80x30 [ 0.000818] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.000853] pid_max: default: 32768 minimum: 301 [ 0.001146] Security Framework initialized [ 0.001333] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001360] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002658] CPU: Testing write buffer coherency: ok [ 0.004230] Setting up static identity map for 0x100000 - 0x100058 [ 0.004627] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.009549] devtmpfs: initialized [ 0.015399] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.015441] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.016050] prandom: seed boundary self test passed [ 0.021784] prandom: 100 self tests passed [ 0.021812] pinctrl core: initialized pinctrl subsystem [ 0.023550] NET: Registered protocol family 16 [ 0.024288] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.026657] cpuidle: using governor ladder [ 0.026767] cpuidle: using governor menu [ 0.027414] Feroceon L2: Enabling L2 [ 0.027479] Feroceon L2: Cache support initialised. [ 0.028028] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.035061] No ATAGs? [ 0.048352] vgaarb: loaded [ 0.048817] SCSI subsystem initialized [ 0.049482] usbcore: registered new interface driver usbfs [ 0.049606] usbcore: registered new interface driver hub [ 0.049727] usbcore: registered new device driver usb [ 0.051397] clocksource: Switched to clocksource orion_clocksource [ 0.183712] VFS: Disk quotas dquot_6.6.0 [ 0.183829] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.198699] NET: Registered protocol family 2 [ 0.199765] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.199806] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.199837] TCP: Hash tables configured (established 1024 bind 1024) [ 0.199967] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.200001] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.200250] NET: Registered protocol family 1 [ 0.200839] RPC: Registered named UNIX socket transport module. [ 0.200856] RPC: Registered udp transport module. [ 0.200867] RPC: Registered tcp transport module. [ 0.200878] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.201213] Unpacking initramfs... [ 1.168680] Freeing initrd memory: 7076K [ 1.168885] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.170259] audit: initializing netlink subsys (disabled) [ 1.170961] Initialise system trusted keyrings [ 1.171044] Key type blacklist registered [ 1.171178] audit: type=2000 audit(1.169:1): state=initialized audit_enabled=0 res=1 [ 1.171312] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.171498] zbud: loaded [ 1.172944] NFS: Registering the id_resolver key type [ 1.172981] Key type id_resolver registered [ 1.172993] Key type id_legacy registered [ 1.173018] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.173033] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.173319] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.173597] fuse init (API version 7.26) [ 1.174112] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.174510] orangefs_init: module version upstream loaded [ 1.174527] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.551406] random: fast init done [ 9.945821] Key type asymmetric registered [ 9.945846] Asymmetric key parser 'x509' registered [ 9.945946] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 9.945962] io scheduler noop registered [ 9.945974] io scheduler deadline registered [ 9.946090] io scheduler cfq registered (default) [ 9.947344] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47 [ 9.947368] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49 [ 9.947868] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.950663] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 9.950695] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 9.950714] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.950734] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.951218] PCI: bus0: Fast back to back transfers disabled [ 9.951254] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.981470] PCI: bus1: Fast back to back transfers disabled [ 9.981760] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 9.981790] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit] [ 9.981824] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit] [ 9.981855] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit] [ 9.981884] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.981908] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 9.982035] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 9.982173] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 9.982900] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.042523] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 10.042838] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.102550] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 10.103178] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.105089] console [ttyS0] disabled [ 10.105183] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 10.811851] console [ttyS0] enabled [ 10.827758] loop: module loaded [ 10.831797] sata_mv f1080000.sata: slots 32 ports 2 [ 10.840544] scsi host0: sata_mv [ 10.844377] scsi host1: sata_mv [ 10.847846] ata1: SATA max UDMA/133 irq 32 [ 10.851998] ata2: SATA max UDMA/133 irq 32 [ 10.857346] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 10.863781] nand: Hynix H27U1G8F2BTR-BC [ 10.867604] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 10.875180] Scanning device for bad blocks [ 10.885193] Bad eraseblock 71 at 0x0000008e0000 [ 10.968559] 4 cmdlinepart partitions found on MTD device orion_nand [ 10.974826] Creating 4 MTD partitions on "orion_nand": [ 10.979957] 0x000000000000-0x000000100000 : "u-boot" [ 10.986777] 0x000000100000-0x000000500000 : "uImage" [ 10.993621] 0x000000500000-0x000002500000 : "rootfs" [ 11.000665] 0x000002500000-0x000008000000 : "data" [ 11.009962] libphy: Fixed MDIO Bus: probed [ 11.015213] libphy: orion_mdio_bus: probed [ 11.026565] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 11.183037] ata1: SATA link down (SStatus 0 SControl F300) [ 11.532927] ata2: SATA link down (SStatus 0 SControl F300) [ 12.143502] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:41:5f [ 12.152398] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.158932] ehci-pci: EHCI PCI platform driver [ 12.163481] ehci-orion: EHCI orion driver [ 12.167770] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.173317] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.181177] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 12.211445] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.217776] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.224585] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.231811] usb usb1: Product: EHCI Host Controller [ 12.236673] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 12.243377] usb usb1: SerialNumber: f1050000.ehci [ 12.249034] hub 1-0:1.0: USB hub found [ 12.252917] hub 1-0:1.0: 1 port detected [ 12.257662] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 12.262992] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 12.272018] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010 [ 12.280732] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.287537] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.294762] usb usb2: Product: xHCI Host Controller [ 12.299625] usb usb2: Manufacturer: Linux 4.12.1-kirkwood-tld-1 xhci-hcd [ 12.306329] usb usb2: SerialNumber: 0000:01:00.0 [ 12.311944] hub 2-0:1.0: USB hub found [ 12.315733] hub 2-0:1.0: 2 ports detected [ 12.320421] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 12.325732] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 12.333284] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 12.341571] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 12.348341] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.355565] usb usb3: Product: xHCI Host Controller [ 12.360425] usb usb3: Manufacturer: Linux 4.12.1-kirkwood-tld-1 xhci-hcd [ 12.368070] usb usb3: SerialNumber: 0000:01:00.0 [ 12.373644] hub 3-0:1.0: USB hub found [ 12.377449] hub 3-0:1.0: 2 ports detected [ 12.382581] usbcore: registered new interface driver usb-storage [ 12.389047] mousedev: PS/2 mouse device common for all mice [ 13.441444] rtc-mv f1010300.rtc: internal RTC not ticking [ 13.447067] i2c /dev entries driver [ 13.452606] hidraw: raw HID events driver (C) Jiri Kosina [ 13.458518] drop_monitor: Initializing network drop monitor service [ 13.465166] NET: Registered protocol family 17 [ 13.469710] Key type dns_resolver registered [ 13.475132] registered taskstats version 1 [ 13.479215] Loading compiled-in X.509 certificates [ 13.484109] zswap: loaded using pool lzo/zbud [ 13.503124] Key type big_key registered [ 13.520610] Key type encrypted registered [ 13.526876] hctosys: unable to open rtc device (rtc0) [ 13.536996] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 14.190327] mvsdio f1090000.mvsdio: Got CD GPIO [ 14.327844] mmc0: host does not support reading read-only switch, assuming write-enable [ 14.343395] mmc0: new high speed SDHC card at address 59b4 [ 14.558024] mmcblk0: mmc0:59b4 SDU1 14.7 GiB [ 14.566507] mmcblk0: p1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping root file system [ 24.895438] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 24.931122] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ 27.616050] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ ok done. [....] Waiting for /dev to be fully populated...[ 28.085970] orion_wdt: Initial timeout 25 sec [ 28.207250] marvell-cesa f1030000.crypto: CESA device successfully registered done. [ ok ] Activating swap:. [ 29.742189] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/mmcblk0p1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14458/966656 files, 223559/3859608 blocks . ok [ 30.190592] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:05:41:5f Sending on LPF/eth0/00:25:31:05:41:5f Sending on Socket/fallback DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 [ 38.340635] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 46.661878] NET: Registered protocol family 10 [ 46.673609] Segment Routing with IPv6 DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 DHCPNAK from 10.10.10.10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPREQUEST of 10.10.10.14 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 10.10.10.14 from 10.10.10.10 DHCPACK of 10.10.10.14 from 10.10.10.10 bound to 10.10.10.14 -- renewal in 3492 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1324 (syslogd) . ok [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1323 (klogd) . ok [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0
Re: Debian does not boot on Pogoplug V4 August 09, 2018 12:31PM |
Admin Registered: 13 years ago Posts: 18,560 |
Re: Debian does not boot on Pogoplug V4 August 09, 2018 01:31PM |
Registered: 5 years ago Posts: 1 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 MMC rescan: current device # 0 initialized OK starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 63 30876867 00000000-01 83 loading envs from mmc 0 ... ** File not found /boot/uEnv.txt ** ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** running scan_disk ... Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 17 ms (0 Bytes/s) Found bootable drive on mmc 0 loading uImage ... 3821592 bytes read in 102 ms (35.7 MiB/s) loading uInitrd ... 7245696 bytes read in 175 ms (39.5 MiB/s) loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ... 10284 bytes read in 38 ms (263.7 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 07420000, end 07b08f40 ... OK Loading Device Tree to 0741a000, end 0741f82b ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. ... Debian GNU/Linux 9 debian ttyS0
Re: Debian does not boot on Pogoplug V4 August 28, 2018 04:52PM |
Registered: 7 years ago Posts: 156 |
Re: Debian does not boot on Pogoplug V4 August 28, 2018 07:46PM |
Admin Registered: 13 years ago Posts: 18,560 |