Re: Dell Wyse T10 / T50 July 26, 2018 05:10PM |
Admin Registered: 13 years ago Posts: 18,821 |
Koen
Re: Dell Wyse T10 / T50 July 26, 2018 05:28PM |
Re: Dell Wyse T10 / T50 July 27, 2018 01:06AM |
Registered: 9 years ago Posts: 451 |
Quote
Dove family (application processor)
> -----------------------------------
>
> Flavors:
> 88AP510 a.k.a Armada 510
> Product Brief :
> http://www.marvell.com/application-processors/armada-500/assets/Marvell_Armada510_SoC.pdf
> Hardware Spec :
> http://www.marvell.com/application-processors/armada-500/assets/Armada-510-Hardware-Spec.pdf
> Functional Spec :
> http://www.marvell.com/application-processors/armada-500/assets/Armada-510-Functional-Spec.pdf
> Homepage:
> http://www.marvell.com/application-processors/armada-500/
> Core: ARMv7 compatible
>
> Directory: arch/arm/mach-mvebu (DT enabled
> platforms)
> arch/arm/mach-dove (non-DT enabled
> platforms)
Re: Dell Wyse T10 / T50 July 27, 2018 11:52AM |
Registered: 10 years ago Posts: 226 |
Koen
Re: Dell Wyse T10 / T50 July 27, 2018 04:55PM |
koen@koen-ThinkPad-X220:~$ picocom -b 115200 /dev/ttyUSB0 picocom v2.2 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is : omap is : emap is : crcrlf,delbs, Type [C-a] [C-h] to see available commands Terminal ready Bootstrap 2.33> >
Koen
Re: Dell Wyse T10 / T50 July 28, 2018 03:55PM |
root=/dev/sda3 pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x768-32@60,lcd1:1024x768-32@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1 clcd.lcd0_clk=3 clcd.lcd1_clk=1 splash no_console_suspend kb3310_disable=1 cpufreq_disable=1 vmalloc=384M quiet
Koen
Re: Dell Wyse T10 / T50 July 28, 2018 05:53PM |
rootdelay=20 root=/dev/sdb1 pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x768-32@60,lcd1:1024x768-32@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1 clcd.lcd0_clk=3 clcd.lcd1_clk=1 splash no_console_suspend kb3310_disable=1 cpufreq_disable=1 vmalloc=384M
koen@koen-ThinkPad-X220:~$ picocom -b 115200 /dev/ttyUSB0 picocom v2.2 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is : omap is : emap is : crcrlf,delbs, Type [C-a] [C-h] to see available commands Terminal ready Uncompressing Linux........................................................................................................................................................................................................................................ done, booting the kernel.
VFS: Mounted root (ext3 filesystem) on device 8:17. devtmpfs: mounted Freeing init memory: 180K FATAL: kernel too old Kernel panic: - not syncing: Attempted to kill init!
Koen
Re: Dell Wyse T10 / T50 July 28, 2018 06:05PM |
EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 8:3. devtmpfs: mounted Freeing init memory: 180K wco.c:v0.01 10/02/2012 WriteCO Control Driver udev: starting version 151 ADDRCONF(NETDEV_UP): eth0: link is not ready set clk 1 to 64998375 dividers found (in lookup table) for Fout = 64998375. n=234 d=5 odiv 18 set internal refclk divider to 31.0.(accurate mode) set clk 1 to 148500148 dividers found (in lookup table) for Fout = 148500148. n=1188 d=25 odiv 8 DCON fb callback: blank... YC pitch is 0.User program needs refine YC pitch is 0.User program needs refine set clk 1 to 148500148 dividers found (in lookup table) for Fout = 148500148. n=1188 d=25 odiv 8 eth0: link up, 100 Mb/s, full duplex, flow control disabled ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DCON fb callback: unblanking... eth0: link down eth0: link up, 100 Mb/s, full duplex, flow control disabled eth0: link down eth0: link up, 100 Mb/s, full duplex, flow control disabled eth0: no IPv6 routers present
Re: Dell Wyse T10 / T50 July 29, 2018 04:03AM |
Admin Registered: 13 years ago Posts: 18,821 |
> rootdelay=20 root=/dev/sdb1 pm_disable > usb0Mode=host usb1Mode=host > video=dovefb:lcd0:1024x768-32@60,lcd1:1024x768-32@60 > clcd.lcd0_enable=1 clcd.lcd1_enable=1 > clcd.lcd0_clk=3 clcd.lcd1_clk=1 splash > no_console_suspend kb3310_disable=1 > cpufreq_disable=1 vmalloc=384M >>
> koen@koen-ThinkPad-X220:~$ picocom -b 115200 > /dev/ttyUSB0 > picocom v2.2 > > port is : /dev/ttyUSB0 > flowcontrol : none > baudrate is : 115200 > parity is : none > databits are : 8 > stopbits are : 1 > escape is : C-a > local echo is : no > noinit is : no > noreset is : no > nolock is : no > send_cmd is : sz -vv > receive_cmd is : rz -vv -E > imap is : > omap is : > emap is : crcrlf,delbs, > > Type [C-a] [C-h] to see available commands > > Terminal ready > Uncompressing > Linux........................................................................................................................................................................................................................................ > done, booting the kernel. >>
> VFS: Mounted root (ext3 filesystem) on device > 8:17. > devtmpfs: mounted > Freeing init memory: 180K > FATAL: kernel too old > Kernel panic: - not syncing: Attempted to kill > init! >>
Koen
Re: Dell Wyse T10 / T50 July 29, 2018 06:01AM |
root@koen-ThinkPad-X220:/# mkfs.ext3 /dev/sdc1 -L rootfs mke2fs 1.44.1 (24-Mar-2018) /dev/sdc1 contains a ext3 filesystem labelled 'rootfs' last mounted on /media/koen/rootfs on Sun Jul 29 09:15:41 2018 Proceed anyway? (y/N) y Creating filesystem with 1953536 4k blocks and 488640 inodes Filesystem UUID: 527dc62b-426d-4a74-9440-7e11252367d4 Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632 Allocating group tables: done Writing inode tables: done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: done
root@koen-ThinkPad-X220:/mnt# mount /dev/sdc1 /mnt/temp/ root@koen-ThinkPad-X220:/mnt# cd /mnt/temp/ root@koen-ThinkPad-X220:/mnt/temp# tar -xjf ~koen/Documents/DellWyse/Debian/Debian-4.12.4-mvebu-tld-1-rootfs-bodhi.tar.bz2 root@koen-ThinkPad-X220:/mnt/temp# cd boot root@koen-ThinkPad-X220:/mnt/temp/boot# ll total 40644 drwxr-xr-x 3 root root 4096 Aug 22 2017 ./ drwxrwxrwx 21 root root 4096 Jan 20 2017 ../ -rw-r--r-- 1 root root 155806 Jul 30 2017 config-4.12.4-mvebu-tld-1 drwxr-xr-x 2 root root 4096 Jul 30 2017 dts/ -rw-r--r-- 1 root root 7070172 Aug 22 2017 initrd.img-4.12.4-mvebu-tld-1 -rw-r--r-- 1 root root 8525990 Jul 30 2017 linux-headers-4.12.4-mvebu-tld-1_1.0_armhf.deb -rw------- 1 root root 2615209 Jul 30 2017 System.map-4.12.4-mvebu-tld-1 -rw-r--r-- 1 root root 4021360 Aug 22 2017 uImage -rw-r--r-- 1 root root 7070236 Aug 22 2017 uInitrd -rw------- 1 root root 4021296 Jul 30 2017 vmlinuz-4.12.4-mvebu-tld-1 -rwxr-xr-x 1 root root 4021296 Jul 30 2017 zImage* -rwxr-xr-x 1 root root 4021296 Jul 30 2017 zImage-4.12.4-mvebu-tld-1* root@koen-ThinkPad-X220:/mnt/temp/boot# cp -a zImage-4.12.4-mvebu-tld-1 zImage root@koen-ThinkPad-X220:/mnt/temp/boot# cp -a zImage-4.12.4-mvebu-tld-1 zImage.fdt root@koen-ThinkPad-X220:/mnt/temp/boot# cat dts/dove-dove-db.dtb >> zImage.fdt root@koen-ThinkPad-X220:/mnt/temp/boot# mv uImage uImage.orig root@koen-ThinkPad-X220:/mnt/temp/boot# mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.4-mvebu-tld-1 -d zImage.fdt uImage Image Name: Linux-4.12.4-mvebu-tld-1 Created: Sun Jul 29 11:47:53 2018 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4035253 Bytes = 3940.68 kB = 3.85 MB Load Address: 00008000 Entry Point: 00008000 root@koen-ThinkPad-X220:/mnt/temp/boot# sync root@koen-ThinkPad-X220:/mnt/temp/boot# cd / root@koen-ThinkPad-X220:/# umount /mnt/temp/
Koen
Re: Dell Wyse T10 / T50 July 29, 2018 06:37AM |
xorg timings 640 672 720 832 480 481 484 509 mode 16: < 640x 480@75> pico=31746 fb timings 48 16 32 11 96 2 xorg timings 640 656 752 800 480 491 493 525 mode 17: < 640x 480@72> pico=32102 fb timings 128 24 28 9 40 3 xorg timings 640 664 704 832 480 489 492 520 mode 18: < 640x 480@60> pico=39758 fb timings 48 16 31 11 96 2 xorg timings 640 656 752 800 480 491 493 524 found <1024x768@60>, pixclock=15385 set internal refclk divider to 31.0.(accurate mode) YC pitch is 0.User program needs refine o dovefb: frame buffer device was successfully loaded. rtc-mv rtc-mv: setting system clock to 2018-07-29 11:18:12 UTC (1532863092) Waiting 10sec before mounting root device... usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected usb 1-1.1: new low speed USB device using orion-ehci and address 3 usb 1-1.1: configuration #1 chosen from 1 choice input: PixArt Microsoft USB Optical Mouse as /devices/platform/orion-ehci.0/usb1/1-1/1-1.1/1-1.1:1.0/input/input1 generic-usb 0003:045E:00CB.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt Microsoft USB Optical Mouse] on usb-orion-ehci.0-1.1/input0 usb 1-1.2: new low speed USB device using orion-ehci and address 4 usb 1-1.2: configuration #1 chosen from 1 choice input: CHICONY USB Keyboard as /devices/platform/orion-ehci.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input2 generic-usb 0003:04F2:0116.0002: input,hidraw1: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-orion-ehci.0-1.4/input0 usb 1-1.4: new high speed USB device using orion-ehci and address 5 usb 1-1.4: configuration #1 chosen from 1 choice scsi1 : SCSI emulation for USB Mass Storage devices scsi 1:0:0:0: Direct-Access SanDisk Cruzer 1.26 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) sd 1:0:0:0: [sdb] Assuming drive cache: write through sd 1:0:0:0: [sdb] Assuming drive cache: write through sdb: sdb1 sd 1:0:0:0: [sdb] Assuming drive cache: write through sd 1:0:0:0: [sdb] Attached SCSI removable disk kjournald starting. Commit interval 5 seconds EXT3 FS on sdb1, internal journal EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 8:17. devtmpfs: mounted Freeing init memory: 180K FATAL: kernel too old Kernel panic: - not syncing: Attempted to kill init!
Koen
Re: Dell Wyse T10 / T50 July 29, 2018 06:56AM |
Configuration file wloader.cfg Root Path ./; Kernel Image uImage; RAMDisk Image: uInitrd; Kernel Parameter rootdelay=10 root=/dev/sdb1 pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x768-32@60,lcd1:1024x768-32@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1 clcd.lcd0_clk=3 clcd.lcd1_clk=1 splash no_console_suspend kb3310_disable=1 cpufreq_disable=1 vmalloc=384M Recovery Parameter ootdelay=5 root=/dev/ram0 rw ramdisk_size=136314880 usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x600-16@60-edid,lcd1:1024x768-16@60-edid clcd.lcd0_enable=1 clcd.lcd1_enable=1 pm_disable titan
Koen
Re: Dell Wyse T10 / T50 July 29, 2018 11:15AM |
Koen
Re: Dell Wyse T10 / T50 July 29, 2018 11:49AM |
koen@koen-ThinkPad-X220:~$ picocom -b 115200 /dev/ttyUSB0 picocom v2.2 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is : omap is : emap is : crcrlf,delbs, Type [C-a] [C-h] to see available commands Terminal ready Uncompressing Linux... done, booting the kernel. Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Tue Aug 22 17:09:50 PDT 2017 from 192.168.0.220 on pts/0 Linux debian 4.12.4-mvebu-tld-1 #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian Marvell DB-MV88AP510-BP Development Board Linux version 4.12.4-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 Debian 9.1 Sun Jul 29 09:32:02 PDT 2018 up root@debian:~#
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.4-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [560f5815] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Marvell DB-MV88AP510-BP Development Board [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] free_area_init_node: node 0, pgdat c0d9d700, node_mem_map e6ff8000 [ 0.000000] Normal zone: 1264 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 161792 pages, LIFO batch:31 [ 0.000000] HighMem zone: 100352 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu @e6fd9000 s40460 r8192 d20980 u69632 [ 0.000000] pcpu-alloc: s40460 r8192 d20980 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260880 [ 0.000000] Kernel command line: rootdelay=5 root=/dev/sdb1 pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x600-16@60-edid,lcd1:1024x768-16@60-edid clcd.lcd0_enable=1 clcd.lcd1_enable=1 clcd.lcd0_clk=3 clcd.lcd1_clk=1 vmalloc=384M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1019144K/1048576K available (8192K kernel code, 712K rwdata, 2080K rodata, 1024K init, 331K bss, 29432K reserved, 0K cma-reserved, 401408K highmem) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe8000000 - 0xff800000 ( 376 MB) lowmem : 0xc0000000 - 0xe7800000 ( 632 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0900000 (9184 kB) .init : 0xc0c00000 - 0xc0d00000 (1024 kB) .data : 0xc0d00000 - 0xc0db2308 ( 713 kB) .bss : 0xc0db9a84 - 0xc0e0ca58 ( 332 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000007] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000040] Switching to timer-based delay loop, resolution 6ns [ 0.000583] Console: colour dummy device 80x30 [ 0.001328] console [tty0] enabled [ 0.001370] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001434] pid_max: default: 32768 minimum: 301 [ 0.001624] Security Framework initialized [ 0.001739] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001783] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002580] CPU: Testing write buffer coherency: ok [ 0.002936] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.040179] Setting up static identity map for 0x100000 - 0x100060 [ 0.120086] smp: Bringing up secondary CPUs ... [ 0.120139] smp: Brought up 1 node, 1 CPU [ 0.120175] SMP: Total of 1 processors activated (333.33 BogoMIPS). [ 0.120209] CPU: All CPU(s) started in SVC mode. [ 0.121060] devtmpfs: initialized [ 0.130506] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5 [ 0.131055] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.131133] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.131434] prandom: seed boundary self test passed [ 0.134495] prandom: 100 self tests passed [ 0.134528] pinctrl core: initialized pinctrl subsystem [ 0.135638] NET: Registered protocol family 16 [ 0.136600] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.141197] cpuidle: using governor ladder [ 0.141298] cpuidle: using governor menu [ 0.141723] Dove 88AP510 SoC [ 0.141769] Tauros2: Disabling L2 prefetch. [ 0.141801] Tauros2: Disabling burst8 line fill. [ 0.141830] Tauros2: Enabling L2 cache. [ 0.141858] Tauros2: L2 cache support initialised in ARMv7 mode. [ 0.142232] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.240614] vgaarb: loaded [ 0.240949] SCSI subsystem initialized [ 0.250158] libata version 3.00 loaded. [ 0.250411] usbcore: registered new interface driver usbfs [ 0.250508] usbcore: registered new interface driver hub [ 0.250587] usbcore: registered new device driver usb [ 0.250813] media: Linux media interface: v0.10 [ 0.250884] Linux video capture interface: v2.00 [ 0.260660] clocksource: Switched to clocksource orion_clocksource [ 0.335265] VFS: Disk quotas dquot_6.6.0 [ 0.335386] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.353661] NET: Registered protocol family 2 [ 0.354353] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.354451] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.354561] TCP: Hash tables configured (established 8192 bind 8192) [ 0.354679] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.354735] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.354923] NET: Registered protocol family 1 [ 0.366254] RPC: Registered named UNIX socket transport module. [ 0.366298] RPC: Registered udp transport module. [ 0.366328] RPC: Registered tcp transport module. [ 0.366357] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.366394] PCI: CLS 0 bytes, default 64 [ 0.366582] Unpacking initramfs... [ 0.792745] Freeing initrd memory: 6908K [ 0.793191] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.794911] audit: initializing netlink subsys (disabled) [ 0.796097] Initialise system trusted keyrings [ 0.796166] Key type blacklist registered [ 0.796273] audit: type=2000 audit(0.794:1): state=initialized audit_enabled=0 res=1 [ 0.796520] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.796652] zbud: loaded [ 0.817884] NFS: Registering the id_resolver key type [ 0.817936] Key type id_resolver registered [ 0.817966] Key type id_legacy registered [ 0.818003] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.818039] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.818269] jffs2: version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 0.818783] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.819030] orangefs_init: module version upstream loaded [ 0.824397] Key type asymmetric registered [ 0.824438] Asymmetric key parser 'x509' registered [ 0.824523] bounce: pool size: 64 pages [ 0.824595] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.824646] io scheduler noop registered [ 0.824675] io scheduler deadline registered [ 0.824759] io scheduler cfq registered (default) [ 0.825479] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource [ 0.825652] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware. [ 0.826387] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver [ 0.830154] mv_xor f1060800.dma-engine: Marvell shared XOR driver [ 0.891589] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 0.891975] mv_xor f1060900.dma-engine: Marvell shared XOR driver [ 0.951548] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 1.072581] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.075749] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A [ 1.077455] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A [ 1.078967] sata_mv f10a0000.sata-host: version 1.28 [ 1.079121] sata_mv f10a0000.sata-host: slots 32 ports 1 [ 1.091797] scsi host0: sata_mv [ 1.092254] ata1: SATA max UDMA/133 irq 32 [ 1.093985] m25p80 spi0.0: found s25fl064k, expected m25p32 [ 1.094033] m25p80 spi0.0: s25fl064k (8192 Kbytes) [ 1.096389] libphy: Fixed MDIO Bus: probed [ 1.097559] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.097610] ehci-pci: EHCI PCI platform driver [ 1.097698] ehci-orion: EHCI orion driver [ 1.097883] orion-ehci f1050000.usb-host: EHCI Host Controller [ 1.097942] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1 [ 1.098119] orion-ehci f1050000.usb-host: irq 26, io mem 0xf1050000 [ 1.121074] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.121368] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.121410] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.121460] usb usb1: Product: EHCI Host Controller [ 1.121493] usb usb1: Manufacturer: Linux 4.12.4-mvebu-tld-1 ehci_hcd [ 1.121529] usb usb1: SerialNumber: f1050000.usb-host [ 1.122354] hub 1-0:1.0: USB hub found [ 1.122423] hub 1-0:1.0: 1 port detected [ 1.122936] orion-ehci f1051000.usb-host: EHCI Host Controller [ 1.122997] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2 [ 1.123173] orion-ehci f1051000.usb-host: irq 27, io mem 0xf1051000 [ 1.150673] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.150925] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.150967] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.151017] usb usb2: Product: EHCI Host Controller [ 1.151050] usb usb2: Manufacturer: Linux 4.12.4-mvebu-tld-1 ehci_hcd [ 1.151085] usb usb2: SerialNumber: f1051000.usb-host [ 1.151835] hub 2-0:1.0: USB hub found [ 1.151902] hub 2-0:1.0: 1 port detected [ 1.152941] usbcore: registered new interface driver usblp [ 1.153149] usbcore: registered new interface driver usb-storage [ 1.153604] mousedev: PS/2 mouse device common for all mice [ 1.154706] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 1.155045] i2c /dev entries driver [ 1.158812] orion_wdt: Initial timeout 25 sec [ 1.161579] marvell-cesa f1030000.crypto-engine: CESA device successfully registered [ 1.161862] hidraw: raw HID events driver (C) Jiri Kosina [ 1.162379] usbcore: registered new interface driver usbhid [ 1.162417] usbhid: USB HID core driver [ 1.162651] drop_monitor: Initializing network drop monitor service [ 1.162747] Netfilter messages via NETLINK v0.30. [ 1.162794] ip_set: protocol 6 [ 1.163120] NET: Registered protocol family 10 [ 1.174231] Segment Routing with IPv6 [ 1.174328] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.176142] NET: Registered protocol family 17 [ 1.176232] 8021q: 802.1Q VLAN Support v1.8 [ 1.176298] Key type dns_resolver registered [ 1.176726] ThumbEE CPU extension supported. [ 1.176763] Registering SWP/SWPB emulation handler [ 1.176794] PJ4 iWMMXt v2 coprocessor enabled. [ 1.177645] registered taskstats version 1 [ 1.177682] Loading compiled-in X.509 certificates [ 1.177766] zswap: loaded using pool lzo/zbud [ 1.263330] Key type big_key registered [ 1.270094] Key type encrypted registered [ 1.272321] rtc-mv f10d8500.real-time-clock: setting system clock to 2018-07-29 16:34:17 UTC (1532882057) [ 1.272530] PM: Hibernation image not present or could not be loaded. [ 1.500624] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 1.590632] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300) [ 1.620824] ata1.00: CFA: 1GB ATA Flash Disk, AD B612J, max UDMA/66 [ 1.620863] ata1.00: 2001888 sectors, multi 0: LBA [ 1.650812] ata1.00: configured for UDMA/66 [ 1.661430] scsi 0:0:0:0: Direct-Access ATA 1GB ATA Flash Di 612J PQ: 0 ANSI: 5 [ 1.662880] sd 0:0:0:0: [sda] 2001888 512-byte logical blocks: (1.02 GB/977 MiB) [ 1.662998] sd 0:0:0:0: [sda] Write Protect is off [ 1.663035] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.663144] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.665305] sda: sda1 sda2 sda3 [ 1.667108] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.668758] Freeing unused kernel memory: 1024K [ 1.692765] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 1.692824] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.692862] usb 1-1: Product: USB2.0 Hub [ 1.693822] hub 1-1:1.0: USB hub found [ 1.694249] hub 1-1:1.0: 4 ports detected [ 1.769531] random: udevadm: uninitialized urandom read (16 bytes read) [ 1.773147] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 1.773711] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 1.773852] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 1.779336] random: udevadm: uninitialized urandom read (16 bytes read) [ 1.779969] random: udevadm: uninitialized urandom read (16 bytes read) [ 1.780536] random: udevadm: uninitialized urandom read (16 bytes read) [ 1.781252] random: udevadm: uninitialized urandom read (16 bytes read) [ 1.781728] random: udevadm: uninitialized urandom read (16 bytes read) [ 1.782310] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.010685] usb 1-1.2: new low-speed USB device number 3 using orion-ehci [ 2.149213] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.149647] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.168894] usb 1-1.2: New USB device found, idVendor=04f2, idProduct=0116 [ 2.168950] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.169001] usb 1-1.2: Product: USB Keyboard [ 2.169032] usb 1-1.2: Manufacturer: CHICONY [ 2.175816] input: CHICONY USB Keyboard as /devices/platform/mbus/mbus:internal-regs/f1050000.usb-host/usb1/1-1/1-1.2/1-1.2:1.0/0003:04F2:0116.0001/input/input0 [ 2.176152] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.241603] hid-generic 0003:04F2:0116.0001: input,hidraw0: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-f1050000.usb-host-1.2/input0 [ 2.299700] sdhci: Secure Digital Host Controller Interface driver [ 2.299753] sdhci: Copyright(c) Pierre Ossman [ 2.300522] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.340681] usb 1-1.4: new high-speed USB device number 4 using orion-ehci [ 2.361793] mmc0: SDHCI controller on f1090000.sdio-host [f1090000.sdio-host] using DMA [ 2.421748] mmc1: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA [ 2.459582] random: fast init done [ 2.491624] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5530 [ 2.491683] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.491734] usb 1-1.4: Product: Cruzer [ 2.491765] usb 1-1.4: Manufacturer: SanDisk [ 2.491796] usb 1-1.4: SerialNumber: 20060775210A3B80C5B2 [ 2.492558] usb-storage 1-1.4:1.0: USB Mass Storage device detected [ 2.509763] scsi host1: usb-storage 1-1.4:1.0 [ 3.349187] usbcore: registered new interface driver uas [ 3.531828] scsi 1:0:0:0: Direct-Access SanDisk Cruzer 1.26 PQ: 0 ANSI: 5 [ 3.546418] sd 1:0:0:0: [sdb] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [ 3.547153] sd 1:0:0:0: [sdb] Write Protect is off [ 3.547196] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 3.547929] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.553016] sdb: sdb1 [ 3.556285] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 8.466814] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem [ 8.488050] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) [ 10.861876] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 10.862125] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 12.997412] EXT4-fs (sdb1): re-mounted. Opts: (null) [ 13.219722] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro [ 14.329812] random: crng init done [ 73.549746] usb 1-1.2: USB disconnect, device number 3 root@debian:~#
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00800000 00001000 "spi0.0" root@debian:~# root@debian:~# fw_printenv Cannot open /dev/mtd1: No such file or directory root@debian:~#
Koen
Re: Dell Wyse T10 / T50 July 29, 2018 12:23PM |
recovery parameters=rootdelay=5 root=/dev/sdb1 pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x600-16@60-edid,lcd1:1024x768-16@60-edid clcd.lcd0_enable=1 clcd.lcd1_enable=1 clcd.lcd0_clk=3 clcd.lcd1_clk=1 vmalloc=384M
Koen
Re: Dell Wyse T10 / T50 July 29, 2018 02:22PM |
Re: Dell Wyse T10 / T50 July 30, 2018 12:26AM |
Admin Registered: 13 years ago Posts: 18,821 |
cat /etc/fw_enc.config
Re: Dell Wyse T10 / T50 July 30, 2018 04:59AM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
The main thing which doesn't work so far is the ethernet connection. All commands are send through serial at the moment. I guess this is due to the fact that a generic dove.dtb file was used to embed in the uImage. Is there a way to create a better dtb file by analysing the original / stock system?
Quote
[ 1.093985] m25p80 spi0.0: found s25fl064k, expected m25p32
[ 1.094033] m25p80 spi0.0: s25fl064k (8192 Kbytes)
Quote
The original system also has a lot of firmware files in /lib/firmware. Should I copy those files to the new rootfs?
Koen
Re: Dell Wyse T10 / T50 July 30, 2018 04:02PM |
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0000 0x80000 0x20000 4 root@debian:~#
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00800000 00001000 "spi0.0" root@debian:~#
root@debian:/etc# cat /etc/fw_env.config # MTD device offset size erase_size /dev/mtd0 0xc0000 0x10000 0x10000 root@debian:/etc#
root@debian:/etc# fw_printenv baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 console=console=ttyS0,115200 useNandHal=single mtdparts=mtdparts=spi0.0:768k(u-boot)ro,128k(uboot_env),-(kernel) arcNumber=1789 CASset=min MALLOC_len=5 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::dove:eth0:none image_name=uImage tftpbootcmd=tftpboot 0x2000000 ${image_name}; setenv bootargs ${console} ${mtdparts} ${bootargs_root} nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}${bootargs_end} usb0Mode=${usb0Mode} usb1Mode=${usb1Mode} video=dovefb:lcd0:${lcd0_params},lcd1:${lcd1_params} clcd.lcd0_enable=${lcd0_enable} clcd.lcd1_enable=${lcd1_enable}; bootm 0x2000000; standalone=fsload 0x2000000 ${image_name};setenv bootargs ${console} ${mtdparts} root=/dev/mtdblock0 rw ip=${ipaddr}:${serverip}${bootargs_end} usb0Mode=${usb0Mode} usb1Mode=${usb1Mode} video=dovefb:lcd0:${lcd0_params},lcd1:${lcd1_params} clcd.lcd0_enable=${lcd0_enable} clcd.lcd1_enable=${lcd1_enable}; bootm 0x2000000; bootsd=sflash read a0000 0x2000000 0x300000;setenv bootargs ${console} ${mtdparts} rootdelay=5 root=/dev/mmcblk0 rw usb0Mode=${usb0Mode} usb1Mode=${usb1Mode} video=dovefb:lcd0:${lcd0_params},lcd1:${lcd1_params} clcd.lcd0_enable=${lcd0_enable} clcd.lcd1_enable=${lcd1_enable}; bootm 0x2000000; bootusb=sflash read a0000 0x2000000 0x300000;setenv bootargs ${console} ${mtdparts} rootdelay=5 root=/dev/sda rw usb0Mode=${usb0Mode} usb1Mode=${usb1Mode} video=dovefb:lcd0:${lcd0_params},lcd1:${lcd1_params} clcd.lcd0_enable=${lcd0_enable} clcd.lcd1_enable=${lcd1_enable}; bootm 0x2000000; bootnand=sflash read a0000 0x2000000 0x300000;setenv bootargs ${console} ${mtdparts} ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs rw usb0Mode=${usb0Mode} usb1Mode=${usb1Mode} video=dovefb:lcd0:${lcd0_params},lcd1:${lcd1_params} clcd.lcd0_enable=${lcd0_enable} clcd.lcd1_enable=${lcd1_enable}; bootm 0x2000000; disaMvPnp=no usb0Mode=host usb1Mode=host yuk_ethaddr=00:00:00:EE:51:81 lcd0_enable=0 lcd1_enable=1 ethact=egiga0 bootcmd=sf read 0x2000000 0x400000 0x380000;bootm 0x2000000 stdin=serial stdout=serial stderr=serial passDramInitTag=yes mainlineLinux=yes enaMonExt=no pexMode=RC disL2Cache=no disL2Ecc=no sata_dma_mode=yes netbsd_en=no vxworks_en=no bootcmd_orig=echo Scanning for boot devices;usb start;ide reset;for i in usb ide;do for j in 0 1; do for l in / /boot/;do for m in fat ext2;do setenv interface $i;setenv device $j;setenv prefix $l;setenv fs $m;setenv partition 1;echo Scanning ${fs} ${interface} ${device} on prefix ${prefix} ...;if ${fs}load ${interface} ${device} 1000 ${prefix}boot.scr; then;if imi 1000; then echo boot.scr found! Executing ...;autoscr 1000;fi;fi;done;done;done;done;echo No boot device found. Falling back to TFTP boot;run tftpbootcmd; bootdelay=3 menucmd=wtest t;wconsole y;run usb_kbd get=tftpboot 0x2000000 u-boot-m.bin;go 0x2000000 usb_kbd=echo no USB Keyboard support enaL2ExtraFeatures=yes enaCpuStream=no enaVpuPower=yes enaGpuPower=yes ethaddr=00:80:64:2a:1b:3a bootargs=rootdelay=10 mtdparts=spi0.0:8192k(u-boot)rw root=/dev/sda3 rw ip=10.4.50.165:10.4.50.5:::dove:eth0:none usb0Mode=host usb1Mode=host video=dovefb:lcd0:1366x768-16@60-edid,lcd1:1366x768-16@60-edid clcd.lcd0_enable=1 clcd.lcd1_enable=1 pm_disable no_console_suspend clcd.lcd0_clk=3 clcd.lcd1_clk=1 cpufreq_disable quiet vmalloc=384MB root@debian:/etc#
Koen
Re: Dell Wyse T10 / T50 July 30, 2018 04:25PM |
root@debian:~# dmesg | grep pci [ 1.107385] ehci-pci: EHCI PCI platform driver
Lankom elec Lg-2405s-1 1246mY
Koen
Re: Dell Wyse T10 / T50 July 30, 2018 05:02PM |
Re: Dell Wyse T10 / T50 July 31, 2018 12:19AM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
PCIE: ? not sure, I plugged a wifi card in the slot but the only line mentioning pci in dmesg is as follows:
root@debian:~# dmesg | grep pci [ 1.107385] ehci-pci: EHCI PCI platform driver
Quote
The ethernet chip has the following printed on it:
Lankom elec
Lg-2405s-1
1246mY
Koen
Re: Dell Wyse T10 / T50 July 31, 2018 04:34PM |
[ 1.093985] m25p80 spi0.0: found s25fl064k, expected m25p32 [ 1.094033] m25p80 spi0.0: s25fl064k (8192 Kbytes)
spi-flash@0 { compatible = "st,m25p32"; spi-max-frequency = <0x1312d00>; reg = <0x0>; };
spi-flash@0 { compatible = "st,m25p80"; spi-max-frequency = <0x1312d00>; reg = <0x0>; };
root@debian:~# dmesg | grep spi [ 1.103881] m25p80 spi0.0: found s25fl064k, expected m25p80 [ 1.103929] m25p80 spi0.0: s25fl064k (8192 Kbytes)
&dspi1 { bus-num = <0>; status = "okay"; dspiflash: s25fl064k@0 { #address-cells = <1>; #size-cells = <1>; compatible = "spansion,s25fl064k"; spi-max-frequency = <16000000>; spi-cpol; spi-cpha; reg = <0>; }; };
Re: Dell Wyse T10 / T50 August 01, 2018 03:55AM |
Admin Registered: 13 years ago Posts: 18,821 |
Koen
Re: Dell Wyse T10 / T50 August 01, 2018 03:58PM |
dtc -I dts -O dtb -o dove-T50.dtb dove-T50.dts
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.4-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [560f5815] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Marvell DB-MV88AP510-BP Development Board [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] free_area_init_node: node 0, pgdat c0d9d700, node_mem_map e6ff8000 [ 0.000000] Normal zone: 1264 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 161792 pages, LIFO batch:31 [ 0.000000] HighMem zone: 100352 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu @e6fd9000 s40460 r8192 d20980 u69632 [ 0.000000] pcpu-alloc: s40460 r8192 d20980 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260880 [ 0.000000] Kernel command line: rootdelay=5 root=/dev/sdb1 pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x600-16@60-edid,lcd1:1024x768-16@60-edid clcd.lcd0_enable=1 clcd.lcd1_enable=1 clcd.lcd0_clk=3 clcd.lcd1_clk=1 vmalloc=384M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1019144K/1048576K available (8192K kernel code, 712K rwdata, 2080K rodata, 1024K init, 331K bss, 29432K reserved, 0K cma-reserved, 401408K highmem) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe8000000 - 0xff800000 ( 376 MB) lowmem : 0xc0000000 - 0xe7800000 ( 632 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0900000 (9184 kB) .init : 0xc0c00000 - 0xc0d00000 (1024 kB) .data : 0xc0d00000 - 0xc0db2308 ( 713 kB) .bss : 0xc0db9a84 - 0xc0e0ca58 ( 332 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000007] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000041] Switching to timer-based delay loop, resolution 6ns [ 0.000581] Console: colour dummy device 80x30 [ 0.001326] console [tty0] enabled [ 0.001369] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001433] pid_max: default: 32768 minimum: 301 [ 0.001623] Security Framework initialized [ 0.001738] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001783] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002580] CPU: Testing write buffer coherency: ok [ 0.002939] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.040180] Setting up static identity map for 0x100000 - 0x100060 [ 0.120088] smp: Bringing up secondary CPUs ... [ 0.120140] smp: Brought up 1 node, 1 CPU [ 0.120176] SMP: Total of 1 processors activated (333.33 BogoMIPS). [ 0.120210] CPU: All CPU(s) started in SVC mode. [ 0.121067] devtmpfs: initialized [ 0.130507] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5 [ 0.131053] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.131134] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.131435] prandom: seed boundary self test passed [ 0.134496] prandom: 100 self tests passed [ 0.134528] pinctrl core: initialized pinctrl subsystem [ 0.135634] NET: Registered protocol family 16 [ 0.136597] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.141195] cpuidle: using governor ladder [ 0.141294] cpuidle: using governor menu [ 0.141719] Dove 88AP510 SoC [ 0.141764] Tauros2: Disabling L2 prefetch. [ 0.141797] Tauros2: Disabling burst8 line fill. [ 0.141826] Tauros2: Enabling L2 cache. [ 0.141855] Tauros2: L2 cache support initialised in ARMv7 mode. [ 0.142230] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.240611] vgaarb: loaded [ 0.240954] SCSI subsystem initialized [ 0.250156] libata version 3.00 loaded. [ 0.250398] usbcore: registered new interface driver usbfs [ 0.250490] usbcore: registered new interface driver hub [ 0.250568] usbcore: registered new device driver usb [ 0.250807] media: Linux media interface: v0.10 [ 0.250879] Linux video capture interface: v2.00 [ 0.260654] clocksource: Switched to clocksource orion_clocksource [ 0.335336] VFS: Disk quotas dquot_6.6.0 [ 0.335457] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.353940] NET: Registered protocol family 2 [ 0.354987] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.355086] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.355195] TCP: Hash tables configured (established 8192 bind 8192) [ 0.355314] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.355370] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.355552] NET: Registered protocol family 1 [ 0.376256] RPC: Registered named UNIX socket transport module. [ 0.376300] RPC: Registered udp transport module. [ 0.376330] RPC: Registered tcp transport module. [ 0.376360] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.376397] PCI: CLS 0 bytes, default 64 [ 0.376586] Unpacking initramfs... [ 0.802386] Freeing initrd memory: 6908K [ 0.802833] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.804575] audit: initializing netlink subsys (disabled) [ 0.805761] Initialise system trusted keyrings [ 0.805836] Key type blacklist registered [ 0.805942] audit: type=2000 audit(0.804:1): state=initialized audit_enabled=0 res=1 [ 0.806192] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.806329] zbud: loaded [ 0.827565] NFS: Registering the id_resolver key type [ 0.827616] Key type id_resolver registered [ 0.827646] Key type id_legacy registered [ 0.827683] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.827718] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.827950] jffs2: version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 0.828465] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.828706] orangefs_init: module version upstream loaded [ 0.834081] Key type asymmetric registered [ 0.834122] Asymmetric key parser 'x509' registered [ 0.834207] bounce: pool size: 64 pages [ 0.834279] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.834330] io scheduler noop registered [ 0.834359] io scheduler deadline registered [ 0.834435] io scheduler cfq registered (default) [ 0.835181] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource [ 0.835358] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware. [ 0.836092] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver [ 0.839878] mv_xor f1060800.dma-engine: Marvell shared XOR driver [ 0.901610] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 0.901998] mv_xor f1060900.dma-engine: Marvell shared XOR driver [ 0.961541] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 1.082541] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.085794] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A [ 1.086853] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A [ 1.089000] sata_mv f10a0000.sata-host: version 1.28 [ 1.089155] sata_mv f10a0000.sata-host: slots 32 ports 1 [ 1.101724] scsi host0: sata_mv [ 1.102154] ata1: SATA max UDMA/133 irq 33 [ 1.103877] m25p80 spi0.0: s25fl064k (8192 Kbytes) [ 1.117825] libphy: Fixed MDIO Bus: probed [ 1.122451] libphy: orion_mdio_bus: probed [ 1.122502] mdio_bus f1072004.mdio-bus-mii: /mbus/internal-regs/mdio-bus@72004/ethernet-phy has invalid PHY address [ 1.122564] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 0 [ 1.122820] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 1 [ 1.128775] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 2 [ 1.129042] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 3 [ 1.129296] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 4 [ 1.129555] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 5 [ 1.129816] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 6 [ 1.130078] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 7 [ 1.130338] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 8 [ 1.130840] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 9 [ 1.131123] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 10 [ 1.131384] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 11 [ 1.131644] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 12 [ 1.131905] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 13 [ 1.132167] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 14 [ 1.132427] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 15 [ 1.132689] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 16 [ 1.132950] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 17 [ 1.133211] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 18 [ 1.133472] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 19 [ 1.133733] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 20 [ 1.133994] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 21 [ 1.134256] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 22 [ 1.134516] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 23 [ 1.134777] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 24 [ 1.135038] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 25 [ 1.135300] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 26 [ 1.135561] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 27 [ 1.135822] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 28 [ 1.136083] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 29 [ 1.136344] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 30 [ 1.136605] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 31 [ 1.137133] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 1.231934] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:80:64:aa:7d:6c [ 1.232704] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.232763] ehci-pci: EHCI PCI platform driver [ 1.232905] ehci-orion: EHCI orion driver [ 1.233096] orion-ehci f1050000.usb-host: EHCI Host Controller [ 1.233157] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1 [ 1.233332] orion-ehci f1050000.usb-host: irq 26, io mem 0xf1050000 [ 1.260701] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.260965] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.261007] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.261058] usb usb1: Product: EHCI Host Controller [ 1.261090] usb usb1: Manufacturer: Linux 4.12.4-mvebu-tld-1 ehci_hcd [ 1.261126] usb usb1: SerialNumber: f1050000.usb-host [ 1.261939] hub 1-0:1.0: USB hub found [ 1.262007] hub 1-0:1.0: 1 port detected [ 1.262514] orion-ehci f1051000.usb-host: EHCI Host Controller [ 1.262573] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2 [ 1.262740] orion-ehci f1051000.usb-host: irq 27, io mem 0xf1051000 [ 1.290658] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.290950] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.290991] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.291042] usb usb2: Product: EHCI Host Controller [ 1.291074] usb usb2: Manufacturer: Linux 4.12.4-mvebu-tld-1 ehci_hcd [ 1.291109] usb usb2: SerialNumber: f1051000.usb-host [ 1.291849] hub 2-0:1.0: USB hub found [ 1.291920] hub 2-0:1.0: 1 port detected [ 1.292988] usbcore: registered new interface driver usblp [ 1.293199] usbcore: registered new interface driver usb-storage [ 1.293654] mousedev: PS/2 mouse device common for all mice [ 1.294770] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 1.295130] i2c /dev entries driver [ 1.298888] orion_wdt: Initial timeout 25 sec [ 1.301653] marvell-cesa f1030000.crypto-engine: CESA device successfully registered [ 1.301964] hidraw: raw HID events driver (C) Jiri Kosina [ 1.302436] usbcore: registered new interface driver usbhid [ 1.302473] usbhid: USB HID core driver [ 1.302705] drop_monitor: Initializing network drop monitor service [ 1.302800] Netfilter messages via NETLINK v0.30. [ 1.302847] ip_set: protocol 6 [ 1.303173] NET: Registered protocol family 10 [ 1.314413] Segment Routing with IPv6 [ 1.314508] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.316229] NET: Registered protocol family 17 [ 1.316324] 8021q: 802.1Q VLAN Support v1.8 [ 1.316394] Key type dns_resolver registered [ 1.316822] ThumbEE CPU extension supported. [ 1.316858] Registering SWP/SWPB emulation handler [ 1.316890] PJ4 iWMMXt v2 coprocessor enabled. [ 1.317741] registered taskstats version 1 [ 1.317777] Loading compiled-in X.509 certificates [ 1.317858] zswap: loaded using pool lzo/zbud [ 1.405259] Key type big_key registered [ 1.412226] Key type encrypted registered [ 1.414398] rtc-mv f10d8500.real-time-clock: setting system clock to 2018-08-01 20:43:12 UTC (1533156192) [ 1.414596] PM: Hibernation image not present or could not be loaded. [ 1.600633] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300) [ 1.630825] ata1.00: CFA: 1GB ATA Flash Disk, AD B612J, max UDMA/66 [ 1.630864] ata1.00: 2001888 sectors, multi 0: LBA [ 1.640617] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 1.660595] random: fast init done [ 1.660851] ata1.00: configured for UDMA/66 [ 1.671482] scsi 0:0:0:0: Direct-Access ATA 1GB ATA Flash Di 612J PQ: 0 ANSI: 5 [ 1.672952] sd 0:0:0:0: [sda] 2001888 512-byte logical blocks: (1.02 GB/977 MiB) [ 1.673068] sd 0:0:0:0: [sda] Write Protect is off [ 1.673105] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.673210] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.675383] sda: sda1 sda2 sda3 [ 1.677213] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.678861] Freeing unused kernel memory: 1024K [ 1.832589] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 1.832649] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.832687] usb 1-1: Product: USB2.0 Hub [ 1.835503] hub 1-1:1.0: USB hub found [ 1.835845] hub 1-1:1.0: 4 ports detected [ 2.150706] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 2.170522] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.203629] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.204070] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.296835] sdhci: Secure Digital Host Controller Interface driver [ 2.296889] sdhci: Copyright(c) Pierre Ossman [ 2.297582] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.301712] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5530 [ 2.301767] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.301818] usb 1-1.3: Product: Cruzer [ 2.301848] usb 1-1.3: Manufacturer: SanDisk [ 2.301880] usb 1-1.3: SerialNumber: 20060775210A3B80C5B2 [ 2.302641] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 2.319793] scsi host1: usb-storage 1-1.3:1.0 [ 2.370726] mmc0: SDHCI controller on f1090000.sdio-host [f1090000.sdio-host] using DMA [ 2.420792] mmc0: new high speed SD card at address b368 [ 2.433092] mmc1: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA [ 3.347668] usbcore: registered new interface driver uas [ 3.362518] mmcblk0: mmc0:b368 SDC 1.87 GiB [ 3.365383] mmcblk0: p1 [ 3.373286] scsi 1:0:0:0: Direct-Access SanDisk Cruzer 1.26 PQ: 0 ANSI: 5 [ 3.385748] sd 1:0:0:0: [sdb] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [ 3.386494] sd 1:0:0:0: [sdb] Write Protect is off [ 3.386537] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 3.387241] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.392601] sdb: sdb1 [ 3.395994] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 8.875650] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem [ 8.896902] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) [ 11.240153] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 11.242386] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 13.475803] EXT4-fs (sdb1): re-mounted. Opts: (null) [ 13.698558] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro [ 13.919149] random: crng init done [ 16.243337] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 18.776603] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 18.776717] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
root@debian:~# ping google.com PING google.com (172.217.17.238) 56(84) bytes of data. 64 bytes from ber01s08-in-f238.1e100.net (172.217.17.238): icmp_seq=1 ttl=50 time=48.7 ms 64 bytes from ber01s08-in-f238.1e100.net (172.217.17.238): icmp_seq=2 ttl=50 time=50.4 ms 64 bytes from ber01s08-in-f238.1e100.net (172.217.17.238): icmp_seq=3 ttl=50 time=48.7 ms 64 bytes from ber01s08-in-f238.1e100.net (172.217.17.238): icmp_seq=4 ttl=50 time=48.5 ms 64 bytes from ber01s08-in-f238.1e100.net (172.217.17.238): icmp_seq=5 ttl=50 time=48.1 ms 64 bytes from ber01s08-in-f238.1e100.net (172.217.17.238): icmp_seq=6 ttl=50 time=48.0 ms ^C --- google.com ping statistics --- 6 packets transmitted, 6 received, 0% packet loss, time 5007ms rtt min/avg/max/mdev = 48.085/48.769/50.470/0.842 ms root@debian:~#
Re: Dell Wyse T10 / T50 August 01, 2018 04:11PM |
Registered: 6 years ago Posts: 183 |
Re: Dell Wyse T10 / T50 August 02, 2018 12:40AM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
I don't compile the file but use the following command:
dtc -I dts -O dtb -o dove-T50.dtb dove-T50.dts
Anyway I changed the values like your example in my dove-T50.dts file. I also had a quick search for the term 'eth' and this showed up in two sections / nodes which were both set to 'disabled'. So I took a gamble and set the status to 'okay' and reconstructed the dove-T50.dtb file. I've re-created the uImage and now ethernet works although the setup is probably not complete / correct as shown in dmesg below.
Quote
This result does make it very tempting to also switch the audio controller, gpu and lcd sections from 'disabled' to 'okay'. Is there much risk in trying this or do wrongly defined parts just not work?
Re: Dell Wyse T10 / T50 August 02, 2018 07:52AM |
Registered: 6 years ago Posts: 183 |
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.4-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [560f5815] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Marvell DB-MV88AP510-BP Development Board [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] free_area_init_node: node 0, pgdat c0d9d700, node_mem_map e6ff8000 [ 0.000000] Normal zone: 1264 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 161792 pages, LIFO batch:31 [ 0.000000] HighMem zone: 100352 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu @e6fd9000 s40460 r8192 d20980 u69632 [ 0.000000] pcpu-alloc: s40460 r8192 d20980 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260880 [ 0.000000] Kernel command line: rootdelay=5 root=/dev/sdb1 pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x600-16@60-edid,lcd1:1024x768-16@60-edid clcd.lcd0_enable=1 clcd.lcd1_enable=1 clcd.lcd0_clk=3 clcd.lcd1_clk=1 vmalloc=384M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1019144K/1048576K available (8192K kernel code, 712K rwdata, 2080K rodata, 1024K init, 331K bss, 29432K reserved, 0K cma-reserved, 401408K highmem) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe8000000 - 0xff800000 ( 376 MB) lowmem : 0xc0000000 - 0xe7800000 ( 632 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0900000 (9184 kB) .init : 0xc0c00000 - 0xc0d00000 (1024 kB) .data : 0xc0d00000 - 0xc0db2308 ( 713 kB) .bss : 0xc0db9a84 - 0xc0e0ca58 ( 332 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000007] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000041] Switching to timer-based delay loop, resolution 6ns [ 0.000579] Console: colour dummy device 80x30 [ 0.001323] console [tty0] enabled [ 0.001365] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001428] pid_max: default: 32768 minimum: 301 [ 0.001620] Security Framework initialized [ 0.001733] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001778] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002576] CPU: Testing write buffer coherency: ok [ 0.002934] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.040179] Setting up static identity map for 0x100000 - 0x100060 [ 0.120089] smp: Bringing up secondary CPUs ... [ 0.120142] smp: Brought up 1 node, 1 CPU [ 0.120177] SMP: Total of 1 processors activated (333.33 BogoMIPS). [ 0.120211] CPU: All CPU(s) started in SVC mode. [ 0.121064] devtmpfs: initialized [ 0.130507] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5 [ 0.131051] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.131132] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.131433] prandom: seed boundary self test passed [ 0.134494] prandom: 100 self tests passed [ 0.134527] pinctrl core: initialized pinctrl subsystem [ 0.135640] NET: Registered protocol family 16 [ 0.136603] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.141191] cpuidle: using governor ladder [ 0.141289] cpuidle: using governor menu [ 0.141715] Dove 88AP510 SoC [ 0.141760] Tauros2: Disabling L2 prefetch. [ 0.141792] Tauros2: Disabling burst8 line fill. [ 0.141821] Tauros2: Enabling L2 cache. [ 0.141850] Tauros2: L2 cache support initialised in ARMv7 mode. [ 0.142224] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.240628] vgaarb: loaded [ 0.240965] SCSI subsystem initialized [ 0.250156] libata version 3.00 loaded. [ 0.250412] usbcore: registered new interface driver usbfs [ 0.250506] usbcore: registered new interface driver hub [ 0.250584] usbcore: registered new device driver usb [ 0.250829] media: Linux media interface: v0.10 [ 0.250901] Linux video capture interface: v2.00 [ 0.260656] clocksource: Switched to clocksource orion_clocksource [ 0.335270] VFS: Disk quotas dquot_6.6.0 [ 0.335393] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.353907] NET: Registered protocol family 2 [ 0.354994] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.355093] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.355203] TCP: Hash tables configured (established 8192 bind 8192) [ 0.355323] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.355379] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.355565] NET: Registered protocol family 1 [ 0.376211] RPC: Registered named UNIX socket transport module. [ 0.376255] RPC: Registered udp transport module. [ 0.376285] RPC: Registered tcp transport module. [ 0.376314] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.376351] PCI: CLS 0 bytes, default 64 [ 0.376538] Unpacking initramfs... [ 0.802424] Freeing initrd memory: 6908K [ 0.802871] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.804643] audit: initializing netlink subsys (disabled) [ 0.805850] Initialise system trusted keyrings [ 0.805922] Key type blacklist registered [ 0.806028] audit: type=2000 audit(0.804:1): state=initialized audit_enabled=0 res=1 [ 0.806277] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.806410] zbud: loaded [ 0.827641] NFS: Registering the id_resolver key type [ 0.827698] Key type id_resolver registered [ 0.827727] Key type id_legacy registered [ 0.827764] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.827799] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.828036] jffs2: version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 0.828560] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.828813] orangefs_init: module version upstream loaded [ 0.834172] Key type asymmetric registered [ 0.834212] Asymmetric key parser 'x509' registered [ 0.834298] bounce: pool size: 64 pages [ 0.834372] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.834423] io scheduler noop registered [ 0.834452] io scheduler deadline registered [ 0.834529] io scheduler cfq registered (default) [ 0.835312] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource [ 0.835484] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware. [ 0.836215] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver [ 0.839814] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 0.839866] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.839904] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.839943] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.839978] pci_bus 0000:00: scanning bus [ 0.840009] pci 0000:00:01.0: [11ab:0510] type 01 class 0x060400 [ 0.840053] pci 0000:00:01.0: calling pci_fixup_ide_bases+0x0/0x3c [ 0.841885] pci_bus 0000:00: fixups for bus [ 0.841899] PCI: bus0: Fast back to back transfers disabled [ 0.841944] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 0 [ 0.841953] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.842011] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 1 [ 0.842249] pci_bus 0000:01: scanning bus [ 0.842289] pci 0000:01:00.0: [1814:3090] type 00 class 0x028000 [ 0.842321] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff] [ 0.842385] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x3c [ 0.870655] pci_bus 0000:01: fixups for bus [ 0.870668] PCI: bus1: Fast back to back transfers disabled [ 0.870710] pci_bus 0000:01: bus scan returning with max=01 [ 0.870722] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.870733] pci_bus 0000:00: bus scan returning with max=01 [ 0.870745] pci 0000:00:01.0: fixup irq: got 0 [ 0.870752] pci 0000:00:01.0: assigning IRQ 00 [ 0.870861] pci 0000:01:00.0: fixup irq: got 44 [ 0.870869] pci 0000:01:00.0: assigning IRQ 44 [ 0.870902] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 0.870947] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff] [ 0.870989] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.871027] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 0.871140] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 0.871191] pcieport 0000:00:01.0: enabling bus mastering [ 0.872000] mv_xor f1060800.dma-engine: Marvell shared XOR driver [ 0.931556] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 0.931926] mv_xor f1060900.dma-engine: Marvell shared XOR driver [ 0.991565] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 1.112491] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.115899] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A [ 1.116972] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A [ 1.119140] sata_mv f10a0000.sata-host: version 1.28 [ 1.119294] sata_mv f10a0000.sata-host: slots 32 ports 1 [ 1.131812] scsi host0: sata_mv [ 1.132209] ata1: SATA max UDMA/133 irq 33 [ 1.134005] m25p80 spi0.0: s25fl064k (8192 Kbytes) [ 1.146866] libphy: Fixed MDIO Bus: probed [ 1.147724] libphy: orion_mdio_bus: probed [ 1.147766] mdio_bus f1072004.mdio-bus-mii: /mbus/internal-regs/mdio-bus@72004/ethernet-phy has invalid PHY address [ 1.147826] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 0 [ 1.152067] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 1 [ 1.158129] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 2 [ 1.158436] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 3 [ 1.158684] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 4 [ 1.158944] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 5 [ 1.159205] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 6 [ 1.159466] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 7 [ 1.159772] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 8 [ 1.160041] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 9 [ 1.160302] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 10 [ 1.160563] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 11 [ 1.161039] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 12 [ 1.161295] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 13 [ 1.161556] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 14 [ 1.161817] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 15 [ 1.162077] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 16 [ 1.162338] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 17 [ 1.162600] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 18 [ 1.162861] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 19 [ 1.163122] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 20 [ 1.163383] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 21 [ 1.163644] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 22 [ 1.163905] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 23 [ 1.164166] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 24 [ 1.164427] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 25 [ 1.164689] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 26 [ 1.164950] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 27 [ 1.165211] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 28 [ 1.165472] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 29 [ 1.165733] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 30 [ 1.165995] mdio_bus f1072004.mdio-bus-mii: scan phy ethernet-phy at address 31 [ 1.166548] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 1.261966] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:80:64:aa:7d:6c [ 1.262780] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.262838] ehci-pci: EHCI PCI platform driver [ 1.262983] ehci-orion: EHCI orion driver [ 1.263178] orion-ehci f1050000.usb-host: EHCI Host Controller [ 1.263239] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1 [ 1.263416] orion-ehci f1050000.usb-host: irq 26, io mem 0xf1050000 [ 1.290702] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.290979] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.291021] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.291071] usb usb1: Product: EHCI Host Controller [ 1.291104] usb usb1: Manufacturer: Linux 4.12.4-mvebu-tld-1 ehci_hcd [ 1.291139] usb usb1: SerialNumber: f1050000.usb-host [ 1.291967] hub 1-0:1.0: USB hub found [ 1.292034] hub 1-0:1.0: 1 port detected [ 1.292563] orion-ehci f1051000.usb-host: EHCI Host Controller [ 1.292621] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2 [ 1.292788] orion-ehci f1051000.usb-host: irq 27, io mem 0xf1051000 [ 1.320657] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.320904] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.320945] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.320995] usb usb2: Product: EHCI Host Controller [ 1.321028] usb usb2: Manufacturer: Linux 4.12.4-mvebu-tld-1 ehci_hcd [ 1.321063] usb usb2: SerialNumber: f1051000.usb-host [ 1.321830] hub 2-0:1.0: USB hub found [ 1.321899] hub 2-0:1.0: 1 port detected [ 1.322951] usbcore: registered new interface driver usblp [ 1.323152] usbcore: registered new interface driver usb-storage [ 1.323570] mousedev: PS/2 mouse device common for all mice [ 1.324634] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 1.324980] i2c /dev entries driver [ 1.328778] orion_wdt: Initial timeout 25 sec [ 1.331605] marvell-cesa f1030000.crypto-engine: CESA device successfully registered [ 1.331920] hidraw: raw HID events driver (C) Jiri Kosina [ 1.332400] usbcore: registered new interface driver usbhid [ 1.332436] usbhid: USB HID core driver [ 1.332680] drop_monitor: Initializing network drop monitor service [ 1.332769] Netfilter messages via NETLINK v0.30. [ 1.332821] ip_set: protocol 6 [ 1.333148] NET: Registered protocol family 10 [ 1.344397] Segment Routing with IPv6 [ 1.344495] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.346286] NET: Registered protocol family 17 [ 1.346378] 8021q: 802.1Q VLAN Support v1.8 [ 1.346449] Key type dns_resolver registered [ 1.346878] ThumbEE CPU extension supported. [ 1.346914] Registering SWP/SWPB emulation handler [ 1.346946] PJ4 iWMMXt v2 coprocessor enabled. [ 1.347820] registered taskstats version 1 [ 1.347856] Loading compiled-in X.509 certificates [ 1.347941] zswap: loaded using pool lzo/zbud [ 1.436555] Key type big_key registered [ 1.443549] Key type encrypted registered [ 1.445791] rtc-mv f10d8500.real-time-clock: setting system clock to 2018-08-02 12:27:20 UTC (1533212840) [ 1.445988] PM: Hibernation image not present or could not be loaded. [ 1.630634] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300) [ 1.660826] ata1.00: CFA: 1GB ATA Flash Disk, AD B612J, max UDMA/66 [ 1.660866] ata1.00: 2001888 sectors, multi 0: LBA [ 1.670619] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 1.671020] random: fast init done [ 1.690817] ata1.00: configured for UDMA/66 [ 1.701449] scsi 0:0:0:0: Direct-Access ATA 1GB ATA Flash Di 612J PQ: 0 ANSI: 5 [ 1.702945] sd 0:0:0:0: [sda] 2001888 512-byte logical blocks: (1.02 GB/977 MiB) [ 1.703064] sd 0:0:0:0: [sda] Write Protect is off [ 1.703102] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.703208] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.705409] sda: sda1 sda2 sda3 [ 1.707329] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.708979] Freeing unused kernel memory: 1024K [ 1.862550] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 1.862611] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.862648] usb 1-1: Product: USB2.0 Hub [ 1.865442] hub 1-1:1.0: USB hub found [ 1.865803] hub 1-1:1.0: 4 ports detected [ 2.180687] usb 1-1.4: new high-speed USB device number 3 using orion-ehci [ 2.220985] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.223407] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.230921] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.319619] sdhci: Secure Digital Host Controller Interface driver [ 2.319672] sdhci: Copyright(c) Pierre Ossman [ 2.320340] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.331671] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5530 [ 2.331727] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.331777] usb 1-1.4: Product: Cruzer [ 2.331808] usb 1-1.4: Manufacturer: SanDisk [ 2.331839] usb 1-1.4: SerialNumber: 20060775210A3B80C5B2 [ 2.332605] usb-storage 1-1.4:1.0: USB Mass Storage device detected [ 2.348295] scsi host1: usb-storage 1-1.4:1.0 [ 2.401739] mmc0: SDHCI controller on f1090000.sdio-host [f1090000.sdio-host] using DMA [ 2.461796] mmc1: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA [ 3.375758] scsi 1:0:0:0: Direct-Access SanDisk Cruzer 1.26 PQ: 0 ANSI: 5 [ 3.392095] sd 1:0:0:0: [sdb] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [ 3.392828] sd 1:0:0:0: [sdb] Write Protect is off [ 3.392872] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 3.393577] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.394517] usbcore: registered new interface driver uas [ 3.399054] sdb: sdb1 [ 3.402458] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 8.685611] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem [ 8.707011] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) [ 11.123811] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 11.124062] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 11.932052] pci 0000:00:01.0: enabling bus mastering [ 11.932070] rt2800pci 0000:01:00.0: enabling device (0140 -> 0142) [ 11.932134] rt2800pci 0000:01:00.0: enabling bus mastering [ 11.932145] rt2800pci 0000:01:00.0: enabling Mem-Wr-Inval [ 11.937610] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3090, rev 3212 detected [ 11.952429] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected [ 11.982533] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 12.948778] rt2800pci 0000:01:00.0 wlp1s0: renamed from wlan0 [ 13.576022] EXT4-fs (sdb1): re-mounted. Opts: (null) [ 13.801520] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro [ 14.530239] random: crng init done [ 16.363337] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 18.014538] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 18.014654] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready root@debian:~#
Re: Dell Wyse T10 / T50 August 02, 2018 01:02PM |
Admin Registered: 13 years ago Posts: 18,821 |
[ 0.839866] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.839904] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.839943] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.839978] pci_bus 0000:00: scanning bus [ 0.840009] pci 0000:00:01.0: [11ab:0510] type 01 class 0x060400 [ 0.840053] pci 0000:00:01.0: calling pci_fixup_ide_bases+0x0/0x3c [ 0.841885] pci_bus 0000:00: fixups for bus [ 0.841899] PCI: bus0: Fast back to back transfers disabled [ 0.841944] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 0 [ 0.841953] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.842011] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 1 [ 0.842249] pci_bus 0000:01: scanning bus [ 0.842289] pci 0000:01:00.0: [1814:3090] type 00 class 0x028000 [ 0.842321] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff] [ 0.842385] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x3c [ 0.870655] pci_bus 0000:01: fixups for bus [ 0.870668] PCI: bus1: Fast back to back transfers disabled [ 0.870710] pci_bus 0000:01: bus scan returning with max=01 [ 0.870722] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.870733] pci_bus 0000:00: bus scan returning with max=01 [ 0.870745] pci 0000:00:01.0: fixup irq: got 0 [ 0.870752] pci 0000:00:01.0: assigning IRQ 00 [ 0.870861] pci 0000:01:00.0: fixup irq: got 44 [ 0.870869] pci 0000:01:00.0: assigning IRQ 44 [ 0.870902] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 0.870947] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff] [ 0.870989] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.871027] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 0.871140] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 0.871191] pcieport 0000:00:01.0: enabling bus mastering [ 11.932052] pci 0000:00:01.0: enabling bus mastering [ 11.932070] rt2800pci 0000:01:00.0: enabling device (0140 -> 0142) [ 11.932134] rt2800pci 0000:01:00.0: enabling bus mastering [ 11.932145] rt2800pci 0000:01:00.0: enabling Mem-Wr-Inval [ 11.937610] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3090, rev 3212 detected [ 11.952429] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected [ 11.982533] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 12.948778] rt2800pci 0000:01:00.0 wlp1s0: renamed from wlan0
Re: Dell Wyse T10 / T50 August 02, 2018 03:06PM |
Registered: 6 years ago Posts: 183 |
root@debian:~# ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.233 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fe80::280:64ff:feaa:7d6c prefixlen 64 scopeid 0x20<link> ether 00:80:64:aa:7d:6c txqueuelen 1000 (Ethernet) RX packets 420 bytes 36693 (35.8 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 552 bytes 129208 (126.1 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 47 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 4 bytes 218 (218.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 4 bytes 218 (218.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 wlp1s0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 ether 00:0e:8e:29:4a:1e txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@debian:~#
[ 16.243337] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 18.776603] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 18.776717] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 16.363337] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 18.014538] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 18.014654] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready