Welcome! Log In Create A New Profile

Advanced

Debian on HP Thin Client T5335z

Posted by bodhi 
Debian on HP Thin Client T5335z
September 02, 2018 01:36PM
Gravelrash is the thread starter for this HP Thin Client T5335z working thread.

Gravelrash post:

Quote

: Specs
Processor
Marvell ARM Armada 510 @ 1.0 GHz
Video
Marvell ARM integrated graphics
Flash
512 MB
DRAM
1 Gb
Connectivity
10/100/1000 Ethernet (RJ-45)
Emulations
DVI-I digital video output (DVI to VGA adapter included)
I/O and peripheral support
4 USB 2.0; 1 RJ-45; 1 DVI-I; 1 headphone; 1 microphone in; DVI-I includes DVI-to-VGA adapter

Commercial review:

https://www.cnet.com/products/hp-smart-client-t5335z-armada-510-1-ghz-monitor-none-series/specs/

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 2 time(s). Last edit at 09/03/2018 02:00PM by bodhi.
Re: Debian on HP Thin Client T5335z
September 02, 2018 03:18PM
Serial console pinouts.

Left-to-Right, Inside facing out.

MicroJST header

1. GND
2. RxD
3. TxD
4. N/A: 3.3V

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 02, 2018 03:25PM
Serial console bootlog.

__   _     .____    
   	    | ||_| |    |  _ \  
   	    |. _   |    | (._)))   
   	    |  |-| |    |  |      
   	    |_ | |_|.   |_ |  ...  
 ** LOADER **


U-Boot 2009.08 (Aug 24 2011 - 15:11:17)HP version: 5.4.2-V28

BootROM:
       Version on chip: 2.33
       Status: OK
       Retries #: 0
Board: RD-88AP510-Avengers
SoC:   88AP510 (A1)
CPU:   Marvell Sheeva (Rev 5)
       CPU @ 1000Mhz, L2 @ 500Mhz
Write Leveling Results:
       CS0, Lane: 0, value: 5
       CS0, Lane: 1, value: 10
       CS0, Lane: 2, value: 43
       CS0, Lane: 3, value: 28
DRAM:   1 GB
       CS 0: base 0x00000000 size  1 GB
       Addresses 12M - 0M are saved for the U-Boot usage.

Streaming disabled 
L2 Cache Prefetch disabled
L2 Cache ECC disabled
USB 0: Host Mode
USB 1: Host Mode
Setting VPU power ON.
Setting GPU power ON.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0

HP>> printenv
[U-boot variables]
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
ub_mfgphase=0000000
console=console=ttys0,115200
mtdids=nor0=spi0.0
mtdparts=mtdparts=spi0.0:768k(u-boot),8k(uboot_env),8k(pu_env),8k(hp_env)
arcNumber=1789
CASset=min
MALLOC_len=5
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::dove:eth0:none
image_name=uImage
mfg_bootargs=console=ttyS0,115200 vmalloc=384M root=/dev/sdb1 rw rootdelay=12 video=dovefb:lcd0:1024x768-24@60-edid,lcd1:1024x768-16@60-edid clcd.lcd0_enable=1 clcd.lcd1_enable=1 oldI2Cbus=1 cpufreq_disable=1 splash quiet
usb_bootargs=root=/dev/ram video=dovefb oldI2Cbus=1 cpufreq_disable=1
bootusb=sleep 2;usb start;mw 0xf10a239c 0x4025;fatload usb 0:1 0x2000000 /boot/uImage.usb.mc2;fatload usb 0 0x3000000 /boot/uInitrd.usb.mc2
usbboot=setenv bootargs ${mtdparts} ${usb_bootargs}; run bootusb; bootm 0x2000000 0x3000000
thinpro_bootargs=root=/dev/sda1 rw init=/init vmalloc=384M video=dovefb oldI2Cbus=1 cpufreq_disable=1 splash quiet
thinpro=ide reset;mw f10a239c 0x4025;ext2load ide 0:1 0x2000000 /boot/uImage; hprecover; setenv bootargs ${mtdparts}  ${thinpro_bootargs};  bootm 0x2000000
mfgargs=setenv bootargs ${mtdparts} ${mfg_bootargs} init=/init 
mfgboot=sleep 2;usb start;mw 0xf10a239c 0x4025;ext2load usb 0:1 0x2000000 /boot/uImage;run mfgargs;bootm 0x2000000
mfgmode=setenv bootdelay 4; setenv in_mfg Yes; setenvh GotoWOL No; setenvh WOLEnabled No; setenv bootcmd run mfgboot; saveenv; reset
hpmode=setenv bootdelay 0;setenv in_mfg No;setenv bootcmd run thinpro; saveenv; reset
disaMvPnp=no
usb0Mode=host
usb1Mode=host
autoload=no
lcd0_enable=0
lcd1_enable=1
lcd0_params=1280x768-16@60
lcd1_params=1024x768-16@60
ethact=egiga0
mb_sn=C2L06335HT2
ethaddr=F4:CE:xx:xx:xx:xx
gatewayip=10.4.50.5
netmask=255.255.255.0
ipaddr=10.4.50.184
serverip=10.4.50.5
bootdelay=0
in_mfg=No
bootcmd=run thinpro
stdin=serial
stdout=serial
stderr=serial
passDramInitTag=yes
mainlineLinux=yes
enaMonExt=no
disL2Cache=no
disL2Ecc=no
sata_dma_mode=yes
enaL2ExtraFeatures=yes
enaCpuStream=no
enaVpuPower=yes
enaGpuPower=yes

Environment size: 2043/8188 bytes
[PUE-variables]
manufacturer=Hewlett-Packard
product_name=hp t5335z
vendor=mitac
mac=F4:CE:xx:xx:xx:xx
uuid=xxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
serial=xxxxxxxxxx

Environment size: 147/8188 bytes
[HP -variables]
UbootVersion=0x11080028
UbootReleaseDate=08242011
AssetNumber=0
AssetLocation=0
InitialNumlock=On
ClockSpeed=1000
GotoWOL=No
WOLEnabled=No

Environment size: 139/8188 bytes



HP>> bdinfo
arch_number = 0x000006FD
env_t       = 0x00000000
boot_params = 0x00000100
DRAM bank   = 0x00000000
-> start    = 0x00000000
-> size     = 0x40000000
DRAM bank   = 0x00000001
-> start    = 0x00000000
-> size     = 0x00000000
DRAM bank   = 0x00000002
-> start    = 0x00000000
-> size     = 0x00000000
DRAM bank   = 0x00000003
-> start    = 0x00000000
-> size     = 0x00000000
ethaddr     = F4:CE:xx:xx:xx:xx
ip_addr     = 10.4.50.184
baudrate    = 115200 bps


HP>> help
?       - alias for 'help'
SatR    - SatR - sample at reset sub-system, relevent for DB only

audioTest- audioTest - Test audio playback

autoscr - DEPRECATED - use "source" command instead
base    - print or set address offset
bdinfo  - print Board Info structure
beep    - beep - Play beep sound

boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootext2- bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name 

bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootvx  - Boot vxWorks from an ELF image
bubt    - bubt	- Burn an image on the Boot SPI Flash.

chpart  - change active partition
cmp     - memory compare
cmpm    - cmpm	- Compare Memory

coninfo - print console devices and information
cp      - memory copy
cpumap  - cpumap - Display CPU memory mapping settings.

crc32   - checksum calculation
date    - get/set/reset date & time
dclk    - dclk	- Display the MV device CLKs.

dhcp    - boot image via network using DHCP/TFTP protocol
diskboot- diskboot- boot from IDE device

dma     - dma	- Perform DMA using the XOR engine

echo    - echo args to console
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fi      - fi	- Find value in the memory.

fsinfo  - print information about filesystems
fsload  - load binary file from a filesystem image
g       - g	- start application at cached address 'addr'(default addr 0x40000)

go      - start application at address 'addr'
help    - print online help
hprecover- hprecover	- T5335 run USB Image recover feature

i2c     - I2C sub-system
ide     - ide     - IDE sub-system

iminfo  - print header information for application image
imxtract- extract a part of a multi-image
ir      - ir	- reading and changing MV internal register values.

itest   - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
ls      - list files in a directory (default /)
map     - map	- Diasplay address decode windows

md      - memory display
me      - me	- PCI master enable

mm      - memory modify (auto-incrementing address)
mp      - mp	- map PCI BAR

mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nfs     - boot image via network using NFS protocol
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
pciePhyRead- phyRead	- Read PCI-E Phy register

pciePhyWrite- pciePhyWrite	- Write PCI-E Phy register

pdma    - pdma	- Perform PDMA

phyRead - phyRead	- Read Phy register

phyWrite- phyWrite	- Write Phy register

ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
resetenv- resetenv	- earse environment sector to reset all variables to default.

run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
se      - se	- PCI Slave enable

setenv  - set environment variables
setenvh - setenvh  - set HP specific Environment variables

setenvp - setenvp  - set Permanent Environemnt variables

sf      - SPI flash sub-system
sg      - sg	- scanning the PHYs status

sleep   - delay execution for some time
source  - run script from memory
sp      - sp	- Scan PCI bus.

sspi    - SPI utility commands
temp    - temp	- Display the device temprature.

tftpboot- boot image via network using TFTP protocol
ts_report- ts_report	- report touch screen cooridate

ts_test - ts_test	- test touch screen

ubi     - ubi commands
ubifsload- load file from an UBIFS filesystem
ubifsls - list files in a directory
ubifsmount- mount UBIFS volume
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version
volt    - volt	- Display the cpu / core voltage.

wol     - wol	- MFG test Wake On Lan features

HP>> boot

Reset IDE: 
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: JMicron                                  Firm: 100415   Ser#: xxxxxxxxxxxxxxx       
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 462.0 MB = 0.4 GB (946176 x 512)

Loading file "/boot/uImage" from ide device 0:1 (hda1)
2600784 bytes read
Checking Button Status: Button Off
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Linux-2.6.32.9-dove-5.3.6-1-arme
   Created:      2011-08-18  21:39:49 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2600720 Bytes =  2.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux.................................................................................................................................................................... done, booting the kernel.

Note: the console output stopped here. And I don't have a display attached. Most likely we need to turn on tty console in stock, like we did for the HP T5235, to be able to see more kernel booting activities.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 09/02/2018 03:44PM by bodhi.
Re: Debian on HP Thin Client T5335z
September 03, 2018 06:11PM
1st boot into Debian with kernel 4.18.5-mvebu-tld-1!


root@T5335z:~# dmesg 
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.18.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018
[    0.000000] CPU: ARMv7 Processor [560f5815] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: HP Thin Client T5335z
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 262144
[    0.000000]   Normal zone: 1536 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 196608 pages, LIFO batch:31
[    0.000000]   HighMem zone: 65536 pages, LIFO batch:15
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] random: get_random_bytes called from start_kernel+0x78/0x4c4 with crng_init=0
[    0.000000] percpu: Embedded 18 pages/cpu @(ptrval) s41548 r8192 d23988 u73728
[    0.000000] pcpu-alloc: s41548 r8192 d23988 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 260608
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:768k(u-boot),8k(uboot_env),8k(pu_env),8k(hp_env) earlyprintk=serial
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1016040K/1048576K available (9216K kernel code, 790K rwdata, 2304K rodata, 1024K init, 327K bss, 32536K reserved, 0K cma-reserved, 262144K highmem)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
                   lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
                   pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
                   modules : 0xbf000000 - 0xbfe00000   (  14 MB)
                     .text : 0x(ptrval) - 0x(ptrval)   (10208 kB)
                     .init : 0x(ptrval) - 0x(ptrval)   (1024 kB)
                     .data : 0x(ptrval) - 0x(ptrval)   ( 791 kB)
                      .bss : 0x(ptrval) - 0x(ptrval)   ( 328 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000007] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.007822] Switching to timer-based delay loop, resolution 6ns
[    0.014407] Console: colour dummy device 80x30
[    0.018899] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.029409] pid_max: default: 32768 minimum: 301
[    0.034234] Security Framework initialized
[    0.038457] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.045056] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.053040] CPU: Testing write buffer coherency: ok
[    0.058292] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.117974] Setting up static identity map for 0x100000 - 0x100060
[    0.124862] Hierarchical SRCU implementation.
[    0.167881] smp: Bringing up secondary CPUs ...
[    0.172401] smp: Brought up 1 node, 1 CPU
[    0.176391] SMP: Total of 1 processors activated (333.33 BogoMIPS).
[    0.182682] CPU: All CPU(s) started in SVC mode.
[    0.188246] devtmpfs: initialized
[    0.198103] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5
[    0.206493] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.216670] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.223143] prandom: seed boundary self test passed
[    0.231114] prandom: 100 self tests passed
[    0.235196] pinctrl core: initialized pinctrl subsystem
[    0.242889] NET: Registered protocol family 16
[    0.249099] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.256446] audit: initializing netlink subsys (disabled)
[    0.264302] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1
[    0.288153] cpuidle: using governor ladder
[    0.292353] cpuidle: using governor menu
[    0.296478] Dove 88AP510 SoC
[    0.299463] Tauros2: Disabling L2 prefetch.
[    0.303631] Tauros2: Disabling burst8 line fill.
[    0.308339] Tauros2: Enabling L2 cache.
[    0.312159] Tauros2: L2 cache support initialised in ARMv7 mode.
[    0.318536] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.418745] vgaarb: loaded
[    0.421761] SCSI subsystem initialized
[    0.428097] libata version 3.00 loaded.
[    0.428336] usbcore: registered new interface driver usbfs
[    0.433838] usbcore: registered new interface driver hub
[    0.440227] usbcore: registered new device driver usb
[    0.445961] media: Linux media interface: v0.10
[    0.451035] videodev: Linux video capture interface: v2.00
[    0.457000] pps_core: LinuxPPS API ver. 1 registered
[    0.462341] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.471643] PTP clock support registered
[    0.477725] clocksource: Switched to clocksource orion_clocksource
[    0.565374] VFS: Disk quotas dquot_6.6.0
[    0.569393] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.595454] NET: Registered protocol family 2
[    0.601096] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.609388] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.616464] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.623171] TCP: Hash tables configured (established 8192 bind 8192)
[    0.629656] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.635567] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.642175] NET: Registered protocol family 1
[    0.677175] RPC: Registered named UNIX socket transport module.
[    0.683134] RPC: Registered udp transport module.
[    0.687850] RPC: Registered tcp transport module.
[    0.692525] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.698951] PCI: CLS 0 bytes, default 64
[    0.699159] Unpacking initramfs...
[    1.264814] Freeing initrd memory: 8960K
[    1.268995] NetWinder Floating Point Emulator V0.97 (double precision)
[    1.278108] Initialise system trusted keyrings
[    1.282565] Key type blacklist registered
[    1.287678] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[    1.294279] zbud: loaded
[    1.307989] NFS: Registering the id_resolver key type
[    1.313033] Key type id_resolver registered
[    1.317197] Key type id_legacy registered
[    1.321264] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.328000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.334567] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.342134] orangefs_debugfs_init: called with debug mask: :none: :0:
[    1.348848] orangefs_init: module version upstream loaded
[    1.360383] Key type asymmetric registered
[    1.364459] Asymmetric key parser 'x509' registered
[    1.369470] bounce: pool size: 64 pages
[    1.373432] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    1.381102] io scheduler noop registered
[    1.385004] io scheduler deadline registered
[    1.389408] io scheduler cfq registered (default)
[    1.396156] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource
[    1.404678] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware.
[    1.415977] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver
[    1.427078] mvebu-pcie mbus:pcie: PCI host bridge to bus 0000:00
[    1.434220] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    1.440604] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    1.447451] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.453095] pci_bus 0000:00: scanning bus
[    1.453206] pci 0000:00:01.0: [11ab:0510] type 01 class 0x060400
[    1.453621] pci 0000:00:02.0: [11ab:0510] type 01 class 0x060400
[    1.454909] pci_bus 0000:00: fixups for bus
[    1.454925] PCI: bus0: Fast back to back transfers disabled
[    1.460682] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 0
[    1.460692] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.468758] pci 0000:00:02.0: scanning [bus 00-00] behind bridge, pass 0
[    1.468766] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.476734] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 1
[    1.476924] pci_bus 0000:01: scanning bus
[    1.478091] pci_bus 0000:01: fixups for bus
[    1.478098] PCI: bus1: Fast back to back transfers enabled
[    1.483555] pci_bus 0000:01: bus scan returning with max=01
[    1.483567] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.483581] pci 0000:00:02.0: scanning [bus 00-00] behind bridge, pass 1
[    1.483889] pci_bus 0000:02: scanning bus
[    1.484941] pci_bus 0000:02: fixups for bus
[    1.484947] PCI: bus2: Fast back to back transfers enabled
[    1.490464] pci_bus 0000:02: bus scan returning with max=02
[    1.490475] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    1.490487] pci_bus 0000:00: bus scan returning with max=02
[    1.490514] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.495460] pci 0000:00:02.0: PCI bridge to [bus 02]
[    1.500524] pcieport 0000:00:01.0: assign IRQ: got 0
[    1.500546] pcieport 0000:00:01.0: enabling bus mastering
[    1.500613] pcieport 0000:00:02.0: assign IRQ: got 0
[    1.500629] pcieport 0000:00:02.0: enabling bus mastering
[    1.501507] mv_xor f1060800.dma-engine: Marvell shared XOR driver
[    1.568755] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr )
[    1.577019] mv_xor f1060900.dma-engine: Marvell shared XOR driver
[    1.638735] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr )
[    1.771338] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.781853] console [ttyS0] disabled
[    1.786149] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A
[    1.795335] console [ttyS0] enabled
[    1.802567] bootconsole [earlycon0] disabled
[    1.812245] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A
[    1.823133] sata_mv f10a0000.sata-host: version 1.28
[    1.823283] sata_mv f10a0000.sata-host: slots 32 ports 1
[    1.840787] scsi host0: sata_mv
[    1.844436] ata1: SATA max UDMA/133 irq 33
[    1.850607] m25p80 spi0.0: sst25vf080b (1024 Kbytes)
[    1.855564] 4 cmdlinepart partitions found on MTD device spi0.0
[    1.862802] Creating 4 MTD partitions on "spi0.0":
[    1.867582] 0x000000000000-0x0000000c0000 : "u-boot"
[    1.873943] 0x0000000c0000-0x0000000c2000 : "uboot_env"
[    1.880711] 0x0000000c2000-0x0000000c4000 : "pu_env"
[    1.887155] 0x0000000c4000-0x0000000c6000 : "hp_env"
[    1.896233] libphy: Fixed MDIO Bus: probed
[    1.903834] libphy: orion_mdio_bus: probed
[    1.909072] [Firmware Warn]: /mbus/internal-regs/mdio-bus@72004/ethernet-phy: Whitelisted compatible string. Please remove
[    1.927401] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    2.029029] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address f4:ce:xx:xx:xx:xx
[    2.038798] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.045320] ehci-pci: EHCI PCI platform driver
[    2.050298] ehci-orion: EHCI orion driver
[    2.054457] orion-ehci f1050000.usb-host: EHCI Host Controller
[    2.060429] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1
[    2.068740] orion-ehci f1050000.usb-host: irq 26, io mem 0xf1050000
[    2.097843] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00
[    2.104466] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[    2.112743] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.119975] usb usb1: Product: EHCI Host Controller
[    2.124833] usb usb1: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd
[    2.131283] usb usb1: SerialNumber: f1050000.usb-host
[    2.137049] hub 1-0:1.0: USB hub found
[    2.141018] hub 1-0:1.0: 1 port detected
[    2.145653] orion-ehci f1051000.usb-host: EHCI Host Controller
[    2.151764] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2
[    2.159940] orion-ehci f1051000.usb-host: irq 27, io mem 0xf1051000
[    2.187760] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00
[    2.194301] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[    2.202553] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.209758] usb usb2: Product: EHCI Host Controller
[    2.214611] usb usb2: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd
[    2.221041] usb usb2: SerialNumber: f1051000.usb-host
[    2.226722] hub 2-0:1.0: USB hub found
[    2.230691] hub 2-0:1.0: 1 port detected
[    2.235918] usbcore: registered new interface driver usblp
[    2.242056] usbcore: registered new interface driver usb-storage
[    2.248671] mousedev: PS/2 mouse device common for all mice
[    2.255511] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time-clock as rtc0
[    2.265334] i2c /dev entries driver
[    2.271522] orion_wdt: Initial timeout 25 sec
[    2.279853] marvell-cesa f1030000.crypto-engine: CESA device successfully registered
[    2.288413] hidraw: raw HID events driver (C) Jiri Kosina
[    2.294533] usbcore: registered new interface driver usbhid
[    2.300117] random: fast init done
[    2.303900] usbhid: USB HID core driver
[    2.308457] drop_monitor: Initializing network drop monitor service
[    2.315128] NET: Registered protocol family 10
[    2.330937] Segment Routing with IPv6
[    2.334659] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    2.342629] NET: Registered protocol family 17
[    2.347107] 8021q: 802.1Q VLAN Support v1.8
[    2.351381] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[    2.358365] Key type dns_resolver registered
[    2.362763] ata1.00: ATA-7: JMicron, 100415, max UDMA/133
[    2.368404] ThumbEE CPU extension supported.
[    2.372659] Registering SWP/SWPB emulation handler
[    2.377430] PJ4 iWMMXt v2 coprocessor enabled.
[    2.381913] ata1.00: 946176 sectors, multi 1: LBA48 
[    2.388117] registered taskstats version 1
[    2.392340] ata1.00: configured for UDMA/133
[    2.396889] Loading compiled-in X.509 certificates
[    2.401791] zswap: loaded using pool lzo/zbud
[    2.407230] scsi 0:0:0:0: Direct-Access     ATA      JMicron          15   PQ: 0 ANSI: 5
[    2.421362] sd 0:0:0:0: [sda] 946176 512-byte logical blocks: (484 MB/462 MiB)
[    2.440998] sd 0:0:0:0: [sda] Write Protect is off
[    2.446292] Key type big_key registered
[    2.454177] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.454333] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    2.467420] Key type encrypted registered
[    2.474926] rtc-mv f10d8500.real-time-clock: setting system clock to 2018-09-03 23:48:22 UTC (1536018502)
[    2.485697]  sda: sda1
[    2.489469] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.496808] Freeing unused kernel memory: 1024K
[    2.503323] Checked W+X mappings: passed, no W+X pages found
[    2.509042] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    2.610797] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    2.626593] random: udevadm: uninitialized urandom read (16 bytes read)
[    2.633999] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    2.718370] usb 1-1: New USB device found, idVendor=058f, idProduct=6254, bcdDevice= 1.00
[    2.726534] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.755819] hub 1-1:1.0: USB hub found
[    2.770106] hub 1-1:1.0: 4 ports detected
[    3.087835] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[    3.132514] i2c i2c-0: Added multiplexed i2c bus 1
[    3.153358] i2c i2c-0: Added multiplexed i2c bus 2
[    3.171788] i2c i2c-0: Added multiplexed i2c bus 3
[    3.234220] sdhci: Secure Digital Host Controller Interface driver
[    3.249108] usb 1-1.1: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00
[    3.257446] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.277831] usb 1-1.1: Product: Ultra Fit
[    3.281855] usb 1-1.1: Manufacturer: SanDisk
[    3.286102] usb 1-1.1: SerialNumber: xxxxxxxxxxxxxxxxxxxx
[    3.308823] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[    3.317860] sdhci: Copyright(c) Pierre Ossman
[    3.323218] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.332837] scsi host1: usb-storage 1-1.1:1.0
[    3.347408] mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
[    3.417083] mmc0: SDHCI controller on f1090000.sdio-host [f1090000.sdio-host] using DMA
[    3.455569] mmc1 bounce up to 128 segments into one, max segment size 65536 bytes
[    3.511416] mmc1: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA
[    4.339215] scsi 1:0:0:0: Direct-Access     SanDisk  Ultra Fit        1.00 PQ: 0 ANSI: 6
[    4.356659] sd 1:0:0:0: [sdb] 30031250 512-byte logical blocks: (15.4 GB/14.3 GiB)
[    4.372406] sd 1:0:0:0: [sdb] Write Protect is off
[    4.377182] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[    4.381067] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    4.407939]  sdb: sdb1
[    4.413530] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[    4.571553] usbcore: registered new interface driver uas
[   15.138937] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem
[   15.172448] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[   17.907913] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   17.964922] sd 1:0:0:0: Attached scsi generic sg1 type 0
[   20.690587] EXT4-fs (sdb1): re-mounted. Opts: user_xattr,acl,errors=remount-ro
[   21.101935] random: crng init done
[   21.105333] random: 7 urandom warning(s) missed due to ratelimiting
[   22.057353] Adding 524284k swap on /swapfile1.  Priority:-2 extents:11 across:10760920k FS
[   26.807279] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   28.575027] fuse init (API version 7.27)
[   29.140474] NET: Registered protocol family 15
[   32.166957] Bluetooth: Core ver 2.22
[   32.174514] NET: Registered protocol family 31
[   32.189226] Bluetooth: HCI device and connection manager initialized
[   32.195573] Bluetooth: HCI socket layer initialized
[   32.213298] Bluetooth: L2CAP socket layer initialized
[   32.224149] Bluetooth: SCO socket layer initialized
[   32.304368] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   32.318022] Bluetooth: BNEP filters: protocol multicast
[   32.323245] Bluetooth: BNEP socket layer initialized
[   38.605793] NFSD: starting 90-second grace period (net f0000029)
[   47.181609] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   47.203288] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)

root@T5335z:~# myinfo 
T5335z
192.168.0.253  
HP Thin Client T5335z
Linux version 4.18.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018
Debian 9.4
console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:768k(u-boot),8k(uboot_env),8k(pu_env),8k(hp_env) earlyprintk=serial
--- System Stats:
/dev/sda: JMicron: 0°C
/dev/sdb: SanDisk:  drive supported, but it doesn't have a temperature sensor.

Mon Sep 3 17:09:39 PDT 2018 up 21 minutes

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 04, 2018 06:00AM
!!!!! WOW !!!!!

I'm impressed at the speed you have gone on this one....
Re: Debian on HP Thin Client T5335z
September 04, 2018 12:35PM
Gravelrash Wrote:
-------------------------------------------------------
> !!!!! WOW !!!!!
>
> I'm impressed at the speed you have gone on this
> one....

:) This box has the same SoC as the Dell Wyse T50.

What we don't have yet for this box is GPL for u-boot and kernel. I'm looking for GPIO info. And see if it will be possible to create new u-boot for this.

And I think your experience will be needed to figure out the graphics capability in this box.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 04, 2018 12:54PM
My unit arrives later this week but it seems like I've missed most of the fun :-)

Koen
Re: Debian on HP Thin Client T5335z
September 04, 2018 02:05PM
Koen Wrote:
-------------------------------------------------------
> My unit arrives later this week but it seems like
> I've missed most of the fun :-)
>

Not really :) Since I had a chance to look at the Marvell Dove SoC for the Wyse T50, this box became quite easy!

I think you and Gravelrash will figure out the Display part. I'll will see if I can activate the LCD devices 0 and 1. We have not seen it in dmesg yet, so that's something to shoot for this box and the Wyse T50.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 05, 2018 06:13AM
@Koen

Please jump in, unless things change drastically at my end, i dont envisage me being able to offer input of any real value till October.


@bofhi
You truly are your handle :)

EDIT: corrected Koen spelling



Edited 1 time(s). Last edit at 09/05/2018 06:16AM by Gravelrash.
Re: Debian on HP Thin Client T5335z
September 05, 2018 06:30AM
I have a contact inside a division of HP - ill see what i can find out in relation to " GPL for u-boot and kernel"

Not going to hold my breath as my experience of large organisations is that the right hand doesnt know what the left hand is doing!
Re: Debian on HP Thin Client T5335z
September 05, 2018 09:02PM
I don't have time to look at this now, but if you want the u-boot source it can be found at ftp://ftp.hp.com/pub/tcdebian/pool/thinpro40/source/uboot-t5335z.tgz. There may be other interesting source files located in that same directory. Good news is it seems to be based on a more modern u-boot 2009.08.



Edited 2 time(s). Last edit at 09/05/2018 09:46PM by rayknight.
Re: Debian on HP Thin Client T5335z
September 05, 2018 09:38PM
Also available from HP ftp server is a restore image which seems to require Windows to create:

TITLE: Smart Zero Core Image

VERSION: Z5D42019 Rev. 1
DESCRIPTION:
This package contains a restore utility and image to be used with the supported
Linux thin client models. The utility included in the package is designed to
aid in the deployment of this image.

This package contains a restore utility and image to be used with the supported
Linux thin client models. The utility included in the package is designed to
aid in the deployment of this image.

PURPOSE: Routine
SOFTPAQ NUMBER: SP60180
SUPERSEDES: SP54767
CATEGORY: Operating System - Enhancements and QFEs
SSM SUPPORTED: No

PRODUCT TYPE(S):
Thin Clients

HARDWARE PRODUCT MODEL(S):
HP t5335z Smart Client

SOFTWARE PRODUCT(S):
None

OPERATING SYSTEM(S):
HP Smart Client

LANGUAGE(S):
Chinese(PRC Simplified)
French
German
Japanese
Spanish
US English

ENHANCEMENTS:
* Adds RDP 7.1
* Adds Certificate Manager
* Adds Citrix 12.1
* Adds Admin Mode
* Adds VNC Shadowing
* Adds Citrix Auto Logout Connection Timer
* Adds Enhanced Citrix Connection Manager
* Adds HP Velocity
* Adds HP Multimedia Keyboard support
* Adds Safenet 650/CAC Card support

For full details of the product enhancements, please see the release notes
inside the installer.

PREREQUISITES:
N/A

INSTALLATION INSTRUCTIONS:
1. Download the file by clicking the Download or Obtain Software button and
saving the file to a folder on your hard drive (make a note of the folder where
the downloaded file is saved).

2. Double-click the downloaded file and follow the on-screen instructions.

NOTE: This product is based on Ubuntu Linux and uses some Open Source
components. All Open Sources packages, including HP modifications, can be found
at the following location:
ftp://ftp.hp.com/pub/tcdebian/pool/thinpro42/source/

NOTE: You also may request a copy of the Open Source source code on CD, or
equivalent, by sending a request to: tc.opensource.request@hp.com. This email
alias only services requests for the Open Source source code.


Copyright (c) 2012 Hewlett-Packard Development Company, L.P. 
Re: Debian on HP Thin Client T5335z
September 05, 2018 11:10PM
> Good news is it
> seems to be based on a more modern u-boot 2009.08.

That's ancient :) even older than some Kirkwood boxes.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 06, 2018 04:38AM
bodhi Wrote:
-------------------------------------------------------
> > Good news is it
> > seems to be based on a more modern u-boot
> 2009.08.
>
> That's ancient :) even older than some Kirkwood
> boxes.

Does that give you what you need though in terms of source code to build a new uboot? and or get pointers towards graphics?
Re: Debian on HP Thin Client T5335z
September 06, 2018 06:14AM
Unit arrived. Ssh in stock is disabled so will need to hook up a monitor and keyboard. Lots of dust inside making it hard to decipher chip numbers at the moment. Will have a closer look this evening.

Koen
Re: Debian on HP Thin Client T5335z
September 06, 2018 12:17PM
Gravelrash,

> > > Good news is it
> > > seems to be based on a more modern u-boot
> > 2009.08.
> >
> > That's ancient :) even older than some Kirkwood
> > boxes.
>
> Does that give you what you need though in terms
> of source code to build a new uboot? and or get
> pointers towards graphics?

Yes, even though this u-boot is old (the design is the same as typical pogoplugs and other NAS stock u-boot circa 2010), the information can be extracted and merge into new u-boot.

Graphics is another story. We know which driver this stock kernel uses: dovefb. However, Armada DRM driver has been in mainline since in kernel 3.13.

Quote

Support the "LCD" controllers found on the Marvell Armada 510 devices. There are two controllers on the device, each controller supports graphics and video overlays.

This driver provides no built-in acceleration; acceleration is performed by other IP found on the SoC. This driver provides kernel mode setting and buffer management to userspace.

So I hope we can just ignore the old dovefb and move on to the Armada DRM driver in mainline.

In the new kernel linux-4.18.5-mvebu-tld-1, I've configured the Armada DRM as a module. As long as the module is loaded during boot, we are OK on the kernel side. However, the LCD devices were not activated yet.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 09/06/2018 12:24PM by bodhi.
Re: Debian on HP Thin Client T5335z
September 06, 2018 12:30PM
List of the markings on the larger chips I can decipher:

jmf601 BGBA1 flash
alcor AU6256 USB controller
4x Samsung k4b2g0846D memory
TFP410 TI PanelBus Digital Transmitter
hynix memory (number unreadable)
marvell ethernet chip (M visible, number unreadable)

Koen
Re: Debian on HP Thin Client T5335z
September 06, 2018 01:21PM
Here is how to boot Debian on the HP T5335z.

1. On another Linux box. Download Debian-4.12.4-mvebu-tld-1-rootfs-bodhi.tar.bz2 from the release thread, create the USB rootfs (or use your existing MVEBU rootfs if you have one before for other boxes).

2. Append the DTB to uImage (assuming the USB drive is mounted at /media/rootfs).

a. Download the attached dove-hp-t5335z.dtb and place it in /media/rootfs/dts.
b. Create new uImage

cd /media/rootfs/boot
cp -a zImage-4.12.4-mvebu-tld-1 zImage.fdt
cat dts/dove-hp-t5335z.dtb >> zImage.fdt 
mv uImage uImage.bak
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.4-mvebu-tld-1 -d zImage.fdt uImage
sync

3. Boot

a. Unmount and remove the USB drive and attach it to the T5335z.
b. Power up and interrupt serial console.

setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x2000000 /boot/uImage; ext2load usb 0:1 0x3000000 /boot/uInitrd'
setenv bootcmd_exec 'run set_bootargs; run bootcmd_usb; bootm 0x2000000 0x3000000'
run bootcmd_exec

4. After booted into Debian, log in and ugrade kernel to linux-4.18.5-mvebu-tld-1 from the release thread. This new kernel version has Armada DRM configured in as module.

5. To make it permannently boot into Debian rootfs on USB, and boot to stock OS when the USB rootfs is not attached:

fw_setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
fw_setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x2000000 /boot/uImage; ext2load usb 0:1 0x3000000 /boot/uInitrd'
fw_setenv bootcmd_exec 'run set_bootargs; run bootcmd_usb; bootm 0x2000000 0x3000000'
fw_setenv bootcmd 'run bootcmd_exec; run thinpro'

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 09/12/2018 11:10PM by bodhi.
Attachments:
open | download - dove-hp-t5335z.dtb (13.4 KB)
open | download - dove-hp-t5335z.dts (1.3 KB)
Re: Debian on HP Thin Client T5335z
September 06, 2018 02:59PM
Hi,

I've logged into stock OS and extracted some info. Not sure if it is useful since bodhi already has Debian working however I may as well put it here as a reference. There is no ssh on the device so all commands have been executed locally and the output saved in text files on a USB drive.

Koen

uname:
Linux HPf4ce4625c9fa 2.6.32.9-dove-5.3.6-1-armel #1 Tue Oct 9 10:08:35 MDT 2012 armv7l GNU/Linux

cpuinfo:
Processor	: Marvell PJ4 v7 Processor-wmmx rev 5 (v7l)
BogoMIPS	: 999.42
Features	: swp half thumb fastmult vfp edsp iwmmxt thumbee 
CPU implementer	: 0x56
CPU architecture: 7
CPU variant	: 0x0
CPU part	: 0x581
CPU revision	: 5

Hardware	: Marvell MV88F6781-RD Avengers MID Board
Revision	: 0000
Serial		: 0000000000000000

dmesg:
[    0.000000] Linux version 2.6.32.9-dove-5.3.6-1-armel (root@ubuntu) (gcc version 4.2.0 20070413 (prerelease) (CodeSourcery 2007q1-10. Marvell 2008q3-13 20081204)) #1 Tue Oct 9 10:08:35 MDT 2012
[    0.000000] CPU: Marvell PJ4 v7 Processor-wmmx [560f5815] revision 5 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Marvell MV88F6781-RD Avengers MID Board
[    0.000000] Marvell Dove DRAM parameters found (version = 0x12030029)
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 204800
[    0.000000] free_area_init_node: node 0, pgdat c050d0d0, node_mem_map c054e000
[    0.000000]   Normal zone: 1200 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 152400 pages, LIFO batch:31
[    0.000000] 
[    0.000000] 
[    0.000000] 
[    0.000000] 
[    0.000000]  wait table c0d4e020
[    0.000000]   HighMem zone: 400 pages used for memmap
[    0.000000]   HighMem zone: 50800 pages, LIFO batch:15
[    0.000000] 
[    0.000000] 
[    0.000000] 
[    0.000000] 
[    0.000000]  wait table c0d50040
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 203200
[    0.000000] Kernel command line: mtdparts=spi0.0:768k(u-boot),8k(uboot_env),8k(pu_env),8k(hp_env) root=/dev/sda1 rw init=/init vmalloc=384M video=dovefb oldI2Cbus=1 cpufreq_disable=1 splash quiet
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 600MB 200MB = 800MB total
[    0.000000] Memory: 804288KB available (4668K code, 425K data, 152K init, 204800K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:135
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty0] enabled
[   25.769971] Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
[   26.029937] Mount-cache hash table entries: 512
[   26.030172] CPU: Testing write buffer coherency: ok
[   26.031846] NET: Registered protocol family 16
[   26.032256] Dove MV88AP510-Rev-Unsupported SoC, TCLK = 167MHz
[   26.032272] DOVE_MC @ 0x280 is 010E0202
[   26.032279] PLiao: DOVE_MC @ 0x510 is 010E0101
[   26.032288] Tauros2: Enabling L2 cache.
[   26.032295] Tauros2: L2 cache support initialised in ARMv7 mode.
[   26.032307] Setting gpu clock to 500000000 (divider: 4)
[   26.032320] Setting axi clock to 333000000 (divider: 5)
[   26.032413] zz dove_rd_avng_gpio_init: orion_gpio_set_valid(21,1)
[   26.032423] zz dove_rd_avng_gpio_init: gpio_direction_input(21)Initializing USB0 Host
[   26.032765] Initializing USB1 Host
[   26.033021] LCD0 doesn't use PLL.
[   26.033027] LCD1 uses PLL.
[   26.033033] Turn on PLL accurate mode.
[   26.033535] Dove PCIe port 0: link down, ignoring
[   26.033544] Dove PCIe port 1: link down, ignoring
[   26.036345] bio: create slab <bio-0> at 0
[   26.036585] vgaarb: loaded
[   26.036849] SCSI subsystem initialized
[   26.036914] libata version 3.00 loaded.
[   26.037089] usbcore: registered new interface driver usbfs
[   26.037151] usbcore: registered new interface driver hub
[   26.037209] usbcore: registered new device driver usb
[   26.037528] Switching to clocksource orion_clocksource
[   26.038052] NET: Registered protocol family 2
[   26.038266] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   26.039077] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   26.041286] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[   26.041837] TCP: Hash tables configured (established 131072 bind 65536)
[   26.041847] TCP reno registered
[   26.041981] NET: Registered protocol family 1
[   26.042241] Power Management for Marvell Dove.
[   26.042260] PMU Detected Frequencies CPU 1000Mhz, AXI 250Mhz, L2 500Mhz, DDR 500Mhz
[   26.046251] Dove hwmon thermal sensor initialized.
[   26.046323] cesadev_modinit
[   26.046346] cesadev_probe
[   26.046353] cesadev_init(c005af94)
[   26.046502] mvCesaInit: sessions=640, queue=64, pSram=fdb00000
[   26.058961] highmem bounce pool size: 64 pages
[   26.059461] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   26.059528] NTFS driver 2.1.29 [Flags: R/O].
[   26.059619] fuse init (API version 7.13)
[   26.059902] aufs 2-standalone.tree-32-20100524
[   26.059920] msgmni has been set to 1171
[   26.060361] alg: No test for stdrng (krng)
[   26.060444] io scheduler noop registered
[   26.060452] io scheduler anticipatory registered
[   26.060460] io scheduler deadline registered
[   26.060507] io scheduler cfq registered (default)
[   26.060649] dovedcon has been initialized.
[   26.060679] dovefb_display_init
[   26.060691] dovefb_display driver init ok.
[   26.065782] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   26.066106] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 7) is a 16550A
[   26.066268] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 8) is a 16550A
[   26.066604] brd: module loaded
[   26.068102] loop: module loaded
[   26.068380] sata_mv sata_mv.0: version 1.28
[   26.068469] sata_mv sata_mv.0: slots 32 ports 1
[   26.068874] scsi0 : sata_mv
[   26.069046] ata1: SATA max UDMA/133 irq 62
[   26.069511] orion_spi orion_spi.0: use polling mode
[   26.069637] m25p80 spi0.0: sst25vf080b (1024 Kbytes)
[   26.069657] 4 cmdlinepart partitions found on MTD device spi0.0
[   26.069666] Creating 4 MTD partitions on "spi0.0":
[   26.069678] 0x000000000000-0x0000000c0000 : "u-boot"
[   26.070047] 0x0000000c0000-0x0000000c2000 : "uboot_env"
[   26.070350] 0x0000000c2000-0x0000000c4000 : "pu_env"
[   26.070664] 0x0000000c4000-0x0000000c6000 : "hp_env"
[   26.071102] MV-643xx 10/100/1000 ethernet driver version 1.5
[   26.071164] mv643xx_eth smi: probed
[   26.577563] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[   26.597666] ata1.00: ATA-7: JMicron, 100415, max UDMA/133
[   26.597677] ata1.00: 946176 sectors, multi 1: LBA48 
[   26.617683] ata1.00: configured for UDMA/133
[   26.617935] scsi 0:0:0:0: Direct-Access     ATA      JMicron          1004 PQ: 0 ANSI: 5
[   26.618295] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   26.618413] sd 0:0:0:0: [sda] 946176 512-byte logical blocks: (484 MB/462 MiB)
[   26.618553] sd 0:0:0:0: [sda] Write Protect is off
[   26.618564] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.618637] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   26.618998]  sda: sda1
[   26.619915] sd 0:0:0:0: [sda] Attached SCSI disk
[   27.808198] net eth0: port 0 with MAC address f4:ce:46:25:c9:fa
[   27.809733] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   27.809980] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   27.810027] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   27.837572] orion-ehci orion-ehci.0: irq 24, io mem 0xf1050000
[   27.857557] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   27.857808] usb usb1: configuration #1 chosen from 1 choice
[   27.857917] hub 1-0:1.0: USB hub found
[   27.857951] hub 1-0:1.0: 1 port detected
[   27.858364] orion-ehci orion-ehci.1: Marvell Orion EHCI
[   27.858389] orion-ehci orion-ehci.1: new USB bus registered, assigned bus number 2
[   27.887568] orion-ehci orion-ehci.1: irq 25, io mem 0xf1051000
[   27.907556] orion-ehci orion-ehci.1: USB 2.0 started, EHCI 1.00
[   27.907774] usb usb2: configuration #1 chosen from 1 choice
[   27.907875] hub 2-0:1.0: USB hub found
[   27.907903] hub 2-0:1.0: 1 port detected
[   27.908204] usbcore: registered new interface driver usblp
[   27.908215] Initializing USB Mass Storage driver...
[   27.908293] usbcore: registered new interface driver usb-storage
[   27.908304] USB Mass Storage support registered.
[   27.908341] usbcore: registered new interface driver ums-datafab
[   27.908378] usbcore: registered new interface driver ums-freecom
[   27.908415] usbcore: registered new interface driver ums-jumpshot
[   27.908452] usbcore: registered new interface driver ums-sddr09
[   27.908489] usbcore: registered new interface driver ums-sddr55
[   27.908615] mice: PS/2 mouse device common for all mice
[   27.908817] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   27.908827] IRQ 133/rtc-mv: IRQF_DISABLED is not guaranteed on shared IRQs
[   27.908866] i2c /dev entries driver
[   27.911551] Linux video capture interface: v2.00
[   27.911702] cpuidle: using governor ladder
[   27.911803] cpuidle: using governor menu
[   27.911831] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[   27.911862] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[   27.947819] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   27.987819] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[   28.027818] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[   28.067610] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[   28.067947] usbcore: registered new interface driver usbhid
[   28.067959] usbhid: v2.6:USB HID core driver
[   28.068037] Advanced Linux Sound Architecture Driver Version 1.0.21.
[   28.068201] No device for DAI RT5623
[   28.068399] rt5623: RT5623 Audio Codec 0.02
[   28.069893] asoc: RT5623 <-> mv88fx-i2s1 mapping ok
[   28.098359] ALSA device list:
[   28.098367]   #0: Dove (RT5623)
[   28.099203] TCP cubic registered
[   28.099323] NET: Registered protocol family 10
[   28.101564] NET: Registered protocol family 17
[   28.101579] ThumbEE CPU extension supported.
[   28.101586] XScale iWMMXt coprocessor detected.
[   28.101671] dove_gpio_power_key_init
[   28.101861] input: t5335_power_key as /devices/platform/t5335_power_key.1/input/input0
[   28.102006] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5
[   28.102261] Dove FB driver:
[   28.135977] Initialize /proc/mv_dump_lcd0
[   28.135986] use cat /proc/mv_dump_lcd0 to see reg settings
[   28.169669] dovefb dovefb.0: use ref clock IDT_CLK0
[   28.171882] DoveFB: No kernel parameters provided, using default.
[   28.171897]   o Kernel parameter: 1024x768-16@60.
[   28.171925] ------------<GFX Layer 0 video mode database>-----------
[   28.171946] mode 0: <1920x1200@60> pico=5177
[   28.171951] 	fb timings    336  128   38    1  208    3
[   28.171956] 	xorg timings 1920 2048 2256 2592 1200 1201 1204 1242
[   28.171977] mode 1: <1920x1080@60> pico=6734
[   28.171982] 	fb timings    148   88   36    4   44    5
[   28.171987] 	xorg timings 1920 2008 2052 2200 1080 1084 1089 1125
[   28.172008] mode 2: <1650x1050@60> pico=6888
[   28.172012] 	fb timings    288  104   33    1  184    3
[   28.172018] 	xorg timings 1650 1754 1938 2226 1050 1051 1054 1087
[   28.172038] mode 3: <1366x 768@60> pico=11659
[   28.172043] 	fb timings    216   72   23    1  144    3
[   28.172048] 	xorg timings 1366 1438 1582 1798  768  769  772  795
[   28.172068] mode 4: <1280x1024@60> pico=9262
[   28.172073] 	fb timings    248   48   38    1  112    3
[   28.172078] 	xorg timings 1280 1328 1440 1688 1024 1025 1028 1066
[   28.172099] mode 5: <1280x 720@60> pico=13468
[   28.172103] 	fb timings    220  110   20    5   40    5
[   28.172109] 	xorg timings 1280 1390 1430 1650  720  725  730  750
[   28.172129] mode 6: <1024x 768@85> pico=10581
[   28.172134] 	fb timings    208   48   36    1   96    3
[   28.172139] 	xorg timings 1024 1072 1168 1376  768  769  772  808
[   28.172159] mode 7: <1024x 768@70> pico=13346
[   28.172164] 	fb timings    144   24   29    3  136    6
[   28.172169] 	xorg timings 1024 1048 1184 1328  768  771  777  806
[   28.172190] mode 8: <1024x 768@60> pico=15385
[   28.172194] 	fb timings    160   24   29    3  136    6
[   28.172200] 	xorg timings 1024 1048 1184 1344  768  771  777  806
[   28.172220] mode 9: <1024x 600@60> pico=22401
[   28.172225] 	fb timings     38   38    8    8  100    4
[   28.172230] 	xorg timings 1024 1062 1162 1200  600  608  612  620
[   28.172250] mode 10: < 800x 600@85> pico=17790
[   28.172255] 	fb timings    152   32   27    1   64    3
[   28.172260] 	xorg timings  800  832  896 1048  600  601  604  631
[   28.172281] mode 11: < 800x 600@75> pico=20234
[   28.172285] 	fb timings    160   16   21    1   80    2
[   28.172291] 	xorg timings  800  816  896 1056  600  601  603  624
[   28.172311] mode 12: < 800x 600@72> pico=20052
[   28.172316] 	fb timings     64   56   23   37  120    6
[   28.172321] 	xorg timings  800  856  976 1040  600  637  643  666
[   28.172341] mode 13: < 800x 600@60> pico=25131
[   28.172346] 	fb timings     88   40   23    1  128    4
[   28.172351] 	xorg timings  800  840  968 1056  600  601  605  628
[   28.172372] mode 14: < 800x 600@56> pico=26515
[   28.172376] 	fb timings    128   32   14    1  128    4
[   28.172382] 	xorg timings  800  832  960 1088  600  601  605  619
[   28.172402] mode 15: < 640x 480@85> pico=27780
[   28.172407] 	fb timings    112   32   25    1   48    3
[   28.172412] 	xorg timings  640  672  720  832  480  481  484  509
[   28.172432] mode 16: < 640x 480@75> pico=31746
[   28.172437] 	fb timings     48   16   32   11   96    2
[   28.172442] 	xorg timings  640  656  752  800  480  491  493  525
[   28.172463] mode 17: < 640x 480@72> pico=32102
[   28.172468] 	fb timings    128   24   28    9   40    3
[   28.172473] 	xorg timings  640  664  704  832  480  489  492  520
[   28.172493] mode 18: < 640x 480@60> pico=39758
[   28.172498] 	fb timings     48   16   31   11   96    2
[   28.172503] 	xorg timings  640  656  752  800  480  491  493  524
[   28.172516] found <1024x768@60>, pixclock=15385
[   28.172530] set clk 0 to 64998375
[   28.172542] dividers found (in lookup table) for Fout = 64998375. n=234 d=5 odiv 18
[   28.177586] YC pitch is 0.User program needs refine
[   28.177878] set clk 0 to 64998375
[   28.177889] dividers found (in lookup table) for Fout = 64998375. n=234 d=5 odiv 18
[   28.189619] Console: switching to colour frame buffer device 128x48
[   28.200932]   o dovefb: frame buffer device was successfully loaded.
[   28.200953] Dove FB driver:
[   28.200980] Initialize /proc/mv_dump_lcd1
[   28.200987] use cat /proc/mv_dump_lcd1 to see reg settings
[   28.201015] dovefb dovefb.1: use ref clock accurate_LCDCLK
[   28.201026] DoveFB: No kernel parameters provided, using default.
[   28.201039]   o Kernel parameter: 1024x768-16@60.
[   28.201057] ------------<GFX Layer 1 video mode database>-----------
[   28.201078] mode 0: <1920x1200@60> pico=5177
[   28.201082] 	fb timings    336  128   38    1  208    3
[   28.201088] 	xorg timings 1920 2048 2256 2592 1200 1201 1204 1242
[   28.201108] mode 1: <1920x1080@60> pico=6734
[   28.201113] 	fb timings    148   88   36    4   44    5
[   28.201118] 	xorg timings 1920 2008 2052 2200 1080 1084 1089 1125
[   28.201139] mode 2: <1650x1050@60> pico=6888
[   28.201143] 	fb timings    288  104   33    1  184    3
[   28.201149] 	xorg timings 1650 1754 1938 2226 1050 1051 1054 1087
[   28.201169] mode 3: <1366x 768@60> pico=11659
[   28.201174] 	fb timings    216   72   23    1  144    3
[   28.201179] 	xorg timings 1366 1438 1582 1798  768  769  772  795
[   28.201199] mode 4: <1280x1024@60> pico=9262
[   28.201204] 	fb timings    248   48   38    1  112    3
[   28.201209] 	xorg timings 1280 1328 1440 1688 1024 1025 1028 1066
[   28.201229] mode 5: <1280x 720@60> pico=13468
[   28.201234] 	fb timings    220  110   20    5   40    5
[   28.201239] 	xorg timings 1280 1390 1430 1650  720  725  730  750
[   28.201260] mode 6: <1024x 768@85> pico=10581
[   28.201264] 	fb timings    208   48   36    1   96    3
[   28.201270] 	xorg timings 1024 1072 1168 1376  768  769  772  808
[   28.201290] mode 7: <1024x 768@70> pico=13346
[   28.201295] 	fb timings    144   24   29    3  136    6
[   28.201300] 	xorg timings 1024 1048 1184 1328  768  771  777  806
[   28.201320] mode 8: <1024x 768@60> pico=15385
[   28.201325] 	fb timings    160   24   29    3  136    6
[   28.201330] 	xorg timings 1024 1048 1184 1344  768  771  777  806
[   28.201350] mode 9: <1024x 600@60> pico=22401
[   28.201355] 	fb timings     38   38    8    8  100    4
[   28.201360] 	xorg timings 1024 1062 1162 1200  600  608  612  620
[   28.201381] mode 10: < 800x 600@85> pico=17790
[   28.201386] 	fb timings    152   32   27    1   64    3
[   28.201391] 	xorg timings  800  832  896 1048  600  601  604  631
[   28.201411] mode 11: < 800x 600@75> pico=20234
[   28.201416] 	fb timings    160   16   21    1   80    2
[   28.201421] 	xorg timings  800  816  896 1056  600  601  603  624
[   28.201441] mode 12: < 800x 600@72> pico=20052
[   28.201446] 	fb timings     64   56   23   37  120    6
[   28.201451] 	xorg timings  800  856  976 1040  600  637  643  666
[   28.201472] mode 13: < 800x 600@60> pico=25131
[   28.201477] 	fb timings     88   40   23    1  128    4
[   28.201482] 	xorg timings  800  840  968 1056  600  601  605  628
[   28.201502] mode 14: < 800x 600@56> pico=26515
[   28.201507] 	fb timings    128   32   14    1  128    4
[   28.201512] 	xorg timings  800  832  960 1088  600  601  605  619
[   28.201533] mode 15: < 640x 480@85> pico=27780
[   28.201537] 	fb timings    112   32   25    1   48    3
[   28.201543] 	xorg timings  640  672  720  832  480  481  484  509
[   28.201563] mode 16: < 640x 480@75> pico=31746
[   28.201568] 	fb timings     48   16   32   11   96    2
[   28.201573] 	xorg timings  640  656  752  800  480  491  493  525
[   28.201593] mode 17: < 640x 480@72> pico=32102
[   28.201598] 	fb timings    128   24   28    9   40    3
[   28.201603] 	xorg timings  640  664  704  832  480  489  492  520
[   28.201624] mode 18: < 640x 480@60> pico=39758
[   28.201628] 	fb timings     48   16   31   11   96    2
[   28.201634] 	xorg timings  640  656  752  800  480  491  493  524
[   28.201645] found <1024x768@60>, pixclock=15385
[   28.201718] set internal refclk divider to 31.0.(accurate mode)
[   28.201734] YC pitch is 0.User program needs refine
[   28.201951]   o dovefb: frame buffer device was successfully loaded.
[   28.202189] rtc-mv rtc-mv: setting system clock to 2018-09-06 19:36:28 UTC (1536262588)
[   28.227576] usb 1-1: new high speed USB device using orion-ehci and address 2
[   28.251064] kjournald starting.  Commit interval 5 seconds
[   28.251690] EXT3 FS on sda1, internal journal
[   28.251711] ext3_orphan_cleanup: deleting unreferenced inode 46838
[   28.251834] ext3_orphan_cleanup: deleting unreferenced inode 46837
[   28.251885] ext3_orphan_cleanup: deleting unreferenced inode 46814
[   28.251917] ext3_orphan_cleanup: deleting unreferenced inode 75194
[   28.252105] ext3_orphan_cleanup: deleting unreferenced inode 75191
[   28.252162] ext3_orphan_cleanup: deleting unreferenced inode 75190
[   28.252188] EXT3-fs: sda1: 6 orphan inodes deleted
[   28.252196] EXT3-fs: recovery complete.
[   28.258411] EXT3-fs: mounted filesystem with writeback data mode.
[   28.258446] VFS: Mounted root (ext3 filesystem) on device 8:1.
[   28.258485] Freeing init memory: 152K
[   28.259675] Warning: unable to open an initial console.
[   28.378469] usb 1-1: configuration #1 chosen from 1 choice
[   28.379241] hub 1-1:1.0: USB hub found
[   28.379362] hub 1-1:1.0: 4 ports detected
[   28.449422] EXT3 FS on sda1, internal journal
[   28.657898] usb 1-1.1: new low speed USB device using orion-ehci and address 3
[   28.801869] usb 1-1.1: configuration #1 chosen from 1 choice
[   28.812933] input: CHICONY USB Keyboard as /devices/platform/orion-ehci.0/usb1/1-1/1-1.1/1-1.1:1.0/input/input1
[   28.813095] generic-usb 0003:04F2:0116.0001: input: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-orion-ehci.0-1.1/input0
[   28.907872] usb 1-1.2: new low speed USB device using orion-ehci and address 4
[   29.047988] usb 1-1.2: configuration #1 chosen from 1 choice
[   29.052039] input: PixArt Microsoft USB Optical Mouse as /devices/platform/orion-ehci.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input2
[   29.052224] generic-usb 0003:045E:00CB.0002: input: USB HID v1.11 Mouse [PixArt Microsoft USB Optical Mouse] on usb-orion-ehci.0-1.2/input0
[   31.841468] ipeak0: ipeak_module_init: allocated ipeak_dev=d1750000
[   31.841581] ipeak0: .139 A: IPQ 1.6.1r11921
[   31.841609] ipeak0: .139 I: systemconfig: initialize system configuration.
[   31.848945] ipeak0: .146 I: Clearing statistics
[   31.848978] ipeak0: .146 I: Allocating 1856 bytes of memory for 1 endpoints
[   31.848991] ipeak0: .146 I: Local metrics collection is enabled.
[   31.849003] ipeak0: .146 I: Remote metrics collection NOT enabled.
[   31.849045] ipeak0: .146 A: Set IP Option Mark to 1
[   31.849055] ipeak0: .146 A: Set TCP Option Mark to 1
[   31.849067] ipeak0: .146 I: Setting burstMode to 2
[   31.849099] ipeak0: .146 I: Globally setting the operating mode to 0
[   31.849112] ipeak0: .146 I: Setting mode range to [0...8]
[   31.849124] ipeak0: .146 I: Setting backoff to true
[   31.849136] ipeak0: .146 A: Applied new configuration
[   31.850796] ipeak0: ipeak_module_init: will attach to eth0...
[   31.850811] ipeak0: ipeak_attach_interface: mac address=f4:ce:46:25:c9:fa
[   32.390220] ipeak1: ipeak_module_init: allocated ipeak_dev=d1da5800
[   32.390326] ipeak1: .688 A: IPQ 1.6.1r11921
[   32.390361] ipeak1: .688 I: systemconfig: initialize system configuration.
[   32.397871] ipeak1: .695 I: Clearing statistics
[   32.397913] ipeak1: .695 I: Allocating 1856 bytes of memory for 1 endpoints
[   32.397926] ipeak1: .695 I: Local metrics collection is enabled.
[   32.397938] ipeak1: .695 I: Remote metrics collection NOT enabled.
[   32.397983] ipeak1: .695 A: Set IP Option Mark to 1
[   32.397994] ipeak1: .695 A: Set TCP Option Mark to 1
[   32.398006] ipeak1: .695 I: Setting burstMode to 2
[   32.398037] ipeak1: .695 I: Globally setting the operating mode to 0
[   32.398051] ipeak1: .695 I: Setting mode range to [0...8]
[   32.398062] ipeak1: .695 I: Setting backoff to true
[   32.398075] ipeak1: .695 A: Applied new configuration
[   32.399902] ipeak1: ipeak_module_init: no interface to bind to, delaying search for later...
[   34.787696] ipeak0: .085 A: BIOS UTIL: Vendor: Hewlett-Packard | Product: hp t5335z
[   35.038113] ipeak1: .335 A: BIOS UTIL: Vendor: Hewlett-Packard | Product: hp t5335z
[   35.368515] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   36.114760] BMM Module Vmeta memroy start: 0x3a000000, size: 100663296
[   36.114881] BMM init with size=96MB
[   36.264898] 
[   36.264902] [galcore] registerBase =0xf1840000, registerMemSize = 0x0003ffff, contiguousBase= 0x32000000, contiguousSize = 0x07ffffff
[   36.265205] 
[   36.265208] [galcore] real contiguouSize = 0x07ffffff 
[   36.265219] 
[   36.265221] [galcore] chipModel=0x600,chipRevision=0x19,chipFeatures=0x87ecd,chipMinorFeatures=0x7
[   36.333944] Setting vmeta clock to 500000000 (divider: 4)
[   37.585076] set clk 0 to 64998375
[   37.585091] dividers found (in lookup table) for Fout = 64998375. n=234 d=5 odiv 18
[   37.595271] set clk 0 to 64998375
[   37.595285] dividers found (in lookup table) for Fout = 64998375. n=234 d=5 odiv 18
[   37.621784] set internal refclk divider to 31.0.(accurate mode)
[   37.687707] set clk 0 to 148500148
[   37.687726] dividers found (in lookup table) for Fout = 148500148. n=1188 d=25 odiv 8
[   37.695293] DCON fb callback: blank...
[   37.799935] YC pitch is 0.User program needs refine
[   37.946921] YC pitch is 0.User program needs refine
[   38.070817] set clk 0 to 148500148
[   38.070835] dividers found (in lookup table) for Fout = 148500148. n=1188 d=25 odiv 8
[   39.029481] DCON fb callback: unblanking...
[   58.039745] NET: Registered protocol family 15
[   59.667161] ipeak0: .964 A: Set IP Option Mark to 1
[   59.667176] ipeak0: .964 A: Set TCP Option Mark to 1
[   59.667206] ipeak0: .965 I: Setting mode range to [0...8]
[   59.667222] ipeak0: .965 A: Applied new configuration
[   59.667400] ipeak1: .965 A: Set IP Option Mark to 1
[   59.667412] ipeak1: .965 A: Set TCP Option Mark to 1
[   59.667441] ipeak1: .965 I: Setting mode range to [0...8]
[   59.667456] ipeak1: .965 A: Applied new configuration
[  331.687810] usb 1-1.4: new high speed USB device using orion-ehci and address 5
[  331.829861] usb 1-1.4: configuration #1 chosen from 1 choice
[  331.834324] scsi1 : SCSI emulation for USB Mass Storage devices
[  331.836825] usb-storage: device found at 5
[  331.836834] usb-storage: waiting for device to settle before scanning
[  336.829561] scsi 1:0:0:0: Direct-Access     Generic  Flash Disk       8.07 PQ: 0 ANSI: 4
[  336.830016] sd 1:0:0:0: Attached scsi generic sg1 type 0
[  336.834846] usb-storage: device scan complete
[  336.838018] sd 1:0:0:0: [sdb] 7866368 512-byte logical blocks: (4.02 GB/3.75 GiB)
[  336.838866] sd 1:0:0:0: [sdb] Write Protect is off
[  336.838878] sd 1:0:0:0: [sdb] Mode Sense: 23 00 00 00
[  336.838888] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[  336.842242] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[  336.842256]  sdb: sdb1
[  336.847395] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[  336.847412] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[  337.241426] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

lsmod:
Module                  Size  Used by
af_key                 29315  0 
galcore                65593  0 
bmm_drv                 5592  0 
hp_velocity_wireless   339967  0 
hp_velocity_wired     339958  0 
regex                  42433  2 hp_velocity_wireless,hp_velocity_wired
snd_pcm_oss            35641  0 
snd_mixer_oss          12900  1 snd_pcm_oss

xvinfo:
X-Video Extension version 2.2
screen #0
  Adaptor #0: "Marvell Mixed Overlay Video"
    number of ports: 1
    port base: 62
    operations supported: PutImage 
    supported visuals:
      depth 24, visualID 0x21
    number of attributes: 5
      "XV_ACTIVE_LCD" (range 0 to 1)
              client settable attribute
              client gettable attribute (current value is -1)
      "XV_COLORKEY" (range 0 to -1)
              client settable attribute
              client gettable attribute (current value is 1)
      "XV_AUTOPAINT_COLORKEY" (range 0 to 1)
              client settable attribute
              client gettable attribute (current value is 0)
      "XV_USE_GPU" (range 0 to 1)
              client settable attribute
              client gettable attribute (current value is 1)
      "XV_DEINTERLACE" (range 0 to 1)
              client settable attribute
              client gettable attribute (current value is 0)
    maximum XvImage size: 2048 x 2048
    Number of image formats: 7
      id: 0x32424752 (RGB2)
        guid: 52474200-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: RGB (packed)
        depth: 16
        red, green, blue masks: 0xf800, 0x7e0, 0x1f
      id: 0x41424752 (RGBA)
        guid: 52474241-0000-0010-8000-00aa00389b71
        bits per pixel: 32
        number of planes: 1
        type: RGB (packed)
        depth: 24
        red, green, blue masks: 0xff0000, 0xff00, 0xff
      id: 0x0
        guid: 52474201-0000-0010-8000-00aa00389b71
        bits per pixel: 24
        number of planes: 1
        type: RGB (packed)
        depth: 24
        red, green, blue masks: 0xff0000, 0xff00, 0xff
      id: 0x59565955 (UYVY)
        guid: 55595659-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: YUV (packed)
      id: 0x32595559 (YUY2)
        guid: 59555932-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: YUV (packed)
      id: 0x32315659 (YV12)
        guid: 59563132-0000-0010-8000-00aa00389b71
        bits per pixel: 12
        number of planes: 3
        type: YUV (planar)
      id: 0x30323449 (I420)
        guid: 49343230-0000-0010-8000-00aa00389b71
        bits per pixel: 12
        number of planes: 3
        type: YUV (planar)
  Adaptor #1: "Marvell Textured Video"
    number of ports: 32
    port base: 63
    operations supported: PutImage 
    supported visuals:
      depth 24, visualID 0x21
    number of attributes: 2
      "XV_ACTIVE_LCD" (range 0 to 1)
              client settable attribute
              client gettable attribute (current value is -1)
      "XV_DEINTERLACE" (range 0 to 1)
              client settable attribute
              client gettable attribute (current value is 0)
    maximum XvImage size: 2048 x 2048
    Number of image formats: 7
      id: 0x32424752 (RGB2)
        guid: 52474200-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: RGB (packed)
        depth: 16
        red, green, blue masks: 0xf800, 0x7e0, 0x1f
      id: 0x41424752 (RGBA)
        guid: 52474241-0000-0010-8000-00aa00389b71
        bits per pixel: 32
        number of planes: 1
        type: RGB (packed)
        depth: 24
        red, green, blue masks: 0xff0000, 0xff00, 0xff
      id: 0x0
        guid: 52474201-0000-0010-8000-00aa00389b71
        bits per pixel: 24
        number of planes: 1
        type: RGB (packed)
        depth: 24
        red, green, blue masks: 0xff0000, 0xff00, 0xff
      id: 0x59565955 (UYVY)
        guid: 55595659-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: YUV (packed)
      id: 0x32595559 (YUY2)
        guid: 59555932-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: YUV (packed)
      id: 0x32315659 (YV12)
        guid: 59563132-0000-0010-8000-00aa00389b71
        bits per pixel: 12
        number of planes: 3
        type: YUV (planar)
      id: 0x30323449 (I420)
        guid: 49343230-0000-0010-8000-00aa00389b71
        bits per pixel: 12
        number of planes: 3
        type: YUV (planar)
  Adaptor #2: "Marvell Overlay Video"
    number of ports: 1
    port base: 95
    operations supported: PutImage 
    supported visuals:
      depth 24, visualID 0x21
    number of attributes: 3
      "XV_ACTIVE_LCD" (range 0 to 1)
              client settable attribute
              client gettable attribute (current value is -1)
      "XV_COLORKEY" (range 0 to -1)
              client settable attribute
              client gettable attribute (current value is 1)
      "XV_AUTOPAINT_COLORKEY" (range 0 to 1)
              client settable attribute
              client gettable attribute (current value is 0)
    maximum XvImage size: 2048 x 2048
    Number of image formats: 7
      id: 0x32424752 (RGB2)
        guid: 52474200-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: RGB (packed)
        depth: 16
        red, green, blue masks: 0xf800, 0x7e0, 0x1f
      id: 0x41424752 (RGBA)
        guid: 52474241-0000-0010-8000-00aa00389b71
        bits per pixel: 32
        number of planes: 1
        type: RGB (packed)
        depth: 24
        red, green, blue masks: 0xff0000, 0xff00, 0xff
      id: 0x0
        guid: 52474201-0000-0010-8000-00aa00389b71
        bits per pixel: 24
        number of planes: 1
        type: RGB (packed)
        depth: 24
        red, green, blue masks: 0xff0000, 0xff00, 0xff
      id: 0x59565955 (UYVY)
        guid: 55595659-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: YUV (packed)
      id: 0x32595559 (YUY2)
        guid: 59555932-0000-0010-8000-00aa00389b71
        bits per pixel: 16
        number of planes: 1
        type: YUV (packed)
      id: 0x32315659 (YV12)
        guid: 59563132-0000-0010-8000-00aa00389b71
        bits per pixel: 12
        number of planes: 3
        type: YUV (planar)
      id: 0x30323449 (I420)
        guid: 49343230-0000-0010-8000-00aa00389b71
        bits per pixel: 12
        number of planes: 3
        type: YUV (planar)

mtdinfo:
Count of MTD devices:           4
Present MTD devices:            mtd0, mtd1, mtd2, mtd3
Sysfs interface supported:      yes

/proc/mtd:
dev:    size   erasesize  name
mtd0: 000c0000 00001000 "u-boot"
mtd1: 00002000 00001000 "uboot_env"
mtd2: 00002000 00001000 "pu_env"
mtd3: 00002000 00001000 "hp_env"

/proc/partitions:
major minor  #blocks  name

   7        0     159336 loop0
  31        0        768 mtdblock0
  31        1          8 mtdblock1
  31        2          8 mtdblock2
  31        3          8 mtdblock3
   8        0     473088 sda
   8        1     454576 sda1
   8       16    3933184 sdb
   8       17    3926016 sdb1

mount:
rootfs on / type rootfs (rw)
/dev/root on / type ext3 (rw,relatime,errors=continue,data=writeback)
none on /dev type tmpfs (rw,relatime,mode=755)
none on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620)
none on /sys type sysfs (rw,nosuid,nodev,noexec,relatime)
none on /proc type proc (rw,nosuid,nodev,noexec,relatime)
/dev/sda1 on /.flash type ext3 (rw,relatime,errors=continue,data=writeback)
/dev/loop0 on /.flash/origfs type squashfs (ro,relatime)
none on / type aufs (rw,relatime,si=7870d1d7,noplink)
none on /writable type aufs (rw,relatime,si=784b1f37,noplink)
none on /tmp type tmpfs (rw,relatime)
none on /dev/shm type tmpfs (rw,nosuid,nodev,relatime,size=402476k)
none on /sys/kernel/debug type debugfs (rw,relatime)
none on /tmp type tmpfs (rw,relatime)
none on /var/run type tmpfs (rw,nosuid,relatime,mode=755)
/dev/sdb1 on /tmp/tmpfs/media/GenericFlash_sdb1 type vfat (rw,nosuid,nodev,noexec,noatime,fmask=0111,dmask=0000,allow_utime=0022,codepage=cp437,iocharset=utf8,shortname=mixed,quiet,utf8,flush,errors=remount-ro)

fw_printenv:
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
ub_mfgphase=0000000
console=console=ttys0,115200
mtdids=nor0=spi0.0
mtdparts=mtdparts=spi0.0:768k(u-boot),8k(uboot_env),8k(pu_env),8k(hp_env)
arcNumber=1789
CASset=min
MALLOC_len=5
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::dove:eth0:none
image_name=uImage
mfg_bootargs=console=ttyS0,115200 vmalloc=384M root=/dev/sdb1 rw rootdelay=12 video=dovefb:lcd0:1024x768-24@60-edid,lcd1:1024x768-16@60-edid clcd.lcd0_enable=1 clcd.lcd1_enable=1 oldI2Cbus=1 cpufreq_disable=1 splash quiet
usb_bootargs=root=/dev/ram video=dovefb oldI2Cbus=1 cpufreq_disable=1
bootusb=sleep 2;usb start;mw 0xf10a239c 0x4025;fatload usb 0:1 0x2000000 /boot/uImage.usb.mc2;fatload usb 0 0x3000000 /boot/uInitrd.usb.mc2
usbboot=setenv bootargs ${mtdparts} ${usb_bootargs}; run bootusb; bootm 0x2000000 0x3000000
thinpro_bootargs=root=/dev/sda1 rw init=/init vmalloc=384M video=dovefb oldI2Cbus=1 cpufreq_disable=1 splash quiet
thinpro=ide reset;mw f10a239c 0x4025;ext2load ide 0:1 0x2000000 /boot/uImage; hprecover; setenv bootargs ${mtdparts}  ${thinpro_bootargs};  bootm 0x2000000
mfgargs=setenv bootargs ${mtdparts} ${mfg_bootargs} init=/init 
mfgboot=sleep 2;usb start;mw 0xf10a239c 0x4025;ext2load usb 0:1 0x2000000 /boot/uImage;run mfgargs;bootm 0x2000000
mfgmode=setenv bootdelay 4; setenv in_mfg Yes; setenvh GotoWOL No; setenvh WOLEnabled No; setenv bootcmd run mfgboot; saveenv; reset
hpmode=setenv bootdelay 0;setenv in_mfg No;setenv bootcmd run thinpro; saveenv; reset
disaMvPnp=no
usb0Mode=host
usb1Mode=host
autoload=no
lcd0_enable=0
lcd1_enable=1
lcd0_params=1280x768-16@60
lcd1_params=1024x768-16@60
ethact=egiga0
mb_sn=C8L02779HT2
ethaddr=F4:CE:46:25:C9:FA
gatewayip=10.4.50.5
netmask=255.255.255.0
ipaddr=10.4.50.39
serverip=10.4.50.5
stdin=serial
stdout=serial
stderr=serial
passDramInitTag=yes
mainlineLinux=yes
enaMonExt=no
disL2Cache=no
disL2Ecc=no
sata_dma_mode=yes
enaL2ExtraFeatures=yes
enaCpuStream=no
enaVpuPower=yes
enaGpuPower=yes
bootdelay=0
in_mfg=No
bootcmd=run thinpro

contents of /:
total 7
drwxr-xr-x 19 root root 1024 2018-09-06 20:36 ./
drwxr-xr-x 19 root root 1024 2018-09-06 20:36 ../
drwxr-xr-x  2 root root 1709 2013-10-26 16:03 bin/
lrwxrwxrwx  1 root root   12 2013-10-26 16:12 boot -> /.flash/boot/
drwxrwxrwx  2 root root 1024 2018-09-06 20:33 .config/
drwxr-xr-x 11 root root 3940 2018-09-06 20:50 dev/
lrwxrwxrwx  1 root root   14 2013-10-26 16:12 etc -> ./writable/etc/
drwxr-xr-x 19 root root 1024 2018-09-06 20:36 .flash/
-rw-r--r--  1 root root    2 2013-10-26 16:11 fonts.dir
lrwxrwxrwx  1 root root   16 2013-10-26 16:12 home -> ../writable/home/
drwxr-xr-x 12 root root 3859 2013-10-26 15:49 lib/
lrwxrwxrwx  1 root root   17 2013-10-26 16:12 media -> ./tmp/tmpfs/media/
lrwxrwxrwx  1 root root   15 2013-10-26 16:12 mnt -> ./tmp/tmpfs/mnt/
drwxr-xr-x  2 root root    3 2013-10-26 02:44 opt/
dr-xr-xr-x 82 root root    0 1970-01-01 01:00 proc/
lrwxrwxrwx  1 root root   16 2013-10-26 16:12 root -> ../writable/root/
drwxr-xr-x  2 root root 2241 2013-10-26 16:02 sbin/
drwxr-xr-x  2 root root    3 2013-09-09 15:55 selinux/
drwxr-xr-x  2 root root    3 2013-10-26 02:44 srv/
drwxr-xr-x 12 root root    0 1970-01-01 01:00 sys/
drwxrwxrwt  8 root root  520 2018-09-06 20:41 tmp/
drwxr-xr-x 10 root root  150 2013-10-26 16:06 usr/
drwxr-xr-x  9 root root 1024 2013-10-26 16:12 var/
drwxr-xr-x 13 root root 1024 2018-09-06 20:41 writable/
Re: Debian on HP Thin Client T5335z
September 06, 2018 03:02PM
Below is the Xorg.0.log from stock Ubuntu OS which may help in getting the graphics working in Debian.


X.Org X Server 1.7.6
Release Date: 2010-03-17
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.32.9-dove-5.3.6-1-armel armv7l Ubuntu
Current Operating System: Linux HPf4ce4625c9fa 2.6.32.9-dove-5.3.6-1-armel #1 Tue Oct 9 10:08:35 MDT 2012 armv7l
Kernel command line: mtdparts=spi0.0:768k(u-boot),8k(uboot_env),8k(pu_env),8k(hp_env) root=/dev/sda1 rw init=/init vmalloc=384M video=dovefb oldI2Cbus=1 cpufreq_disable=1 splash quiet
Build Date: 19 August 2013  11:58:13AM
xorg-server 2:1.7.6-2ubuntu7.12 (For technical support please see http://www.ubuntu.com/support) 
Current version of pixman: 0.16.4
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Sep  6 20:36:37 2018
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using config directory: "/etc/X11/xorg.conf.d"
(==) No Layout section.  Using the first Screen section.
(**) |-->Screen "Primary Screen" (0)
(**) |   |-->Monitor "Primary Monitor"
(**) |   |-->Device "Driver0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
	Entry deleted from font path.
(==) FontPath set to:
	/usr/share/fonts/X11/misc,
	built-ins
(==) ModulePath set to "/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
(==) |-->Input Device "Generic Keyboard"
(==) No Layout section. Using the first core keyboard device.
(II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
(II) Loader magic: 0x13bf38
(II) Module ABI versions:
	X.Org ANSI C Emulation: 0.4
	X.Org Video Driver: 6.0
	X.Org XInput driver : 7.0
	X.Org Server Extension : 2.0
(++) using VT number 7

(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.13.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.1.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "dovefb"
(II) Loading /usr/lib/xorg/modules/drivers/dovefb_drv.so
(II) Module fbdev: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 0.3.0
	ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 2.3.2
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 7.0
(II) dovefb: Support Marvell LCD Controller: 88AP510
(WW) Falling back to old probe method for dovefb
(II) Loading sub module "fbdevhw"
(II) LoadModule: "fbdevhw"
(II) Loading /usr/lib/xorg/modules/linux/libfbdevhw.so
(II) Module fbdevhw: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 0.0.2
	ABI class: X.Org Video Driver, version 6.0
(II) dovefb(0): using default device
(II) dovefb(0): source version <1:0.3.4-1>
(II) Running in FRAMEBUFFER Mode
(II) dovefb(0): Enter into PreInit
(II) dovefb(0): ioctl FBIOGET_VSCREENINFO
(**) dovefb(0): Depth 24, (**) framebuffer bpp 32
(==) dovefb(0): RGB weight 888
(==) dovefb(0): Default visual is TrueColor
(==) dovefb(0): Using gamma correction (1.0, 1.0, 1.0)
(II) dovefb(0): hardware: GFX Layer 0 (video memory: 49152kB)
(**) dovefb(0): Option "ShadowFB" "FALSE"
(**) dovefb(0): Option "EncFunc" "0x0b"
(**) dovefb(0): Option "HWcursor" "FALSE"
(**) dovefb(0): Option "ExaAccel" "FALSE"
(**) dovefb(0): Option "XvAccel" "TRUE"
(**) dovefb(0): Option "Solid" "TRUE"
(**) dovefb(0): Option "Copy" "TRUE"
(**) dovefb(0): Option "Composite" "FALSE"
(**) dovefb(0): Option "Commit" "FALSE"
(**) dovefb(0): Option "SWSolid" "FALSE"
(**) dovefb(0): Option "SWCopy" "FALSE"
(**) dovefb(0): Option "UseGPU" "FALSE"
(**) dovefb(0): Option "UseDriverBuiltInMode" "TRUE"
(**) dovefb(0): Option "EnableDualDisplay" "false"
(**) dovefb(0): enhance function is mode <11>
(II) dovefb(0): shadow fb is disabled
(II) dovefb(0): debug is disabled.
(II) dovefb(0): checking modes against framebuffer device...
(II) dovefb(0): checking modes against monitor...
(--) dovefb(0): Virtual size is 1920x1920 (pitch 1920)
(II) dovefb(0): mrvlCrtcInit: Found 2 fb devices
(II) dovefb(0): mrvlCrtcInit: crtc [0], lcd virtual x 1920, y 5760
(II) dovefb(0): mrvlCrtcInit: create crtc0.
(II) dovefb(0): mrvlCrtcInit: crtc0 has been initialized.
(II) dovefb(0): mrvlCrtcInit: crtc [1], lcd virtual x 1920, y 5760
(II) dovefb(0): mrvlCrtcInit: create crtc1.
(II) dovefb(0): mrvlCrtcInit: crtc1 has been initialized.
(II) dovefb(0): mrvlCrtcInit: completed.
(II) dovefb(0): mrvlOutputInit: create output...
(II) dovefb(0): mrvlOutputInit: create output0 at lvds...
(II) dovefb(0): Output lvds using monitor section Primary Monitor
(**) dovefb(0): Option "Enable" "TRUE"
(**) dovefb(0): Option "Rotate" "Normal"
(II) dovefb(0): mrvlOutputInit: create output1 at VGA...
(II) dovefb(0): Output VGA using monitor section Primary Monitor
(II) dovefb(0): mrvlOutputInit: Init output...
(II) dovefb(0): mrvlOutputInit: Init output0.
(II) dovefb(0): mrvlOutputInit: Init output1.
(II) dovefb(0): *** output <lvds>, x=0, y=0
(II) dovefb(0): *** output <VGA>, x=0, y=0
(II) dovefb(0): enter mrvl_detect_edid, there are 2 crtc, output 0
(II) dovefb(0): *#* output<0> is digital.
(II) dovefb(0): monitor id: <Primary Monitor>
(II) dovefb(0): OPTION_ENABLE in config file = 1.
(II) dovefb(0): OPTION_NoDDCValue not define
(II) dovefb(0): In output 0, has monitor-lvds, has monitor-VGA in device section in xorg.conf.
(II) dovefb(0): *** dual display mode is disabled.
(II) dovefb(0): *#** (*pConnectStatus[0])=1
(II) dovefb(0): *#** (*pConnectStatus[1])=1
(II) dovefb(0): mrvl_get_modes_with_edid!
(II) dovefb(0): EDID for output lvds
(II) dovefb(0): Manufacturer: PHL  Model: c0e5  Serial#: 996
(II) dovefb(0): Year: 2015  Week: 47
(II) dovefb(0): EDID Version: 1.3
(II) dovefb(0): Digital Display Input
(II) dovefb(0): Max Image Size [cm]: horiz.: 48  vert.: 27
(II) dovefb(0): Gamma: 2.20
(II) dovefb(0): DPMS capabilities: Off
(II) dovefb(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
(II) dovefb(0): First detailed timing is preferred mode
(II) dovefb(0): redX: 0.647 redY: 0.338   greenX: 0.302 greenY: 0.632
(II) dovefb(0): blueX: 0.147 blueY: 0.061   whiteX: 0.313 whiteY: 0.329
(II) dovefb(0): Supported established timings:
(II) dovefb(0): 720x400@70Hz
(II) dovefb(0): 640x480@60Hz
(II) dovefb(0): 640x480@67Hz
(II) dovefb(0): 640x480@72Hz
(II) dovefb(0): 640x480@75Hz
(II) dovefb(0): 800x600@60Hz
(II) dovefb(0): 800x600@75Hz
(II) dovefb(0): 1024x768@60Hz
(II) dovefb(0): 1024x768@75Hz
(II) dovefb(0): 1280x1024@75Hz
(II) dovefb(0): Manufacturer's mask: 0
(II) dovefb(0): Supported standard timings:
(II) dovefb(0): #0: hsize: 1920  vsize 1080  refresh: 60  vid: 49361
(II) dovefb(0): #1: hsize: 1440  vsize 900  refresh: 60  vid: 149
(II) dovefb(0): #2: hsize: 1440  vsize 900  refresh: 75  vid: 3989
(II) dovefb(0): #3: hsize: 1680  vsize 1050  refresh: 60  vid: 179
(II) dovefb(0): #4: hsize: 1280  vsize 720  refresh: 60  vid: 49281
(II) dovefb(0): #5: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
(II) dovefb(0): Supported detailed timing:
(II) dovefb(0): clock: 148.5 MHz   Image Size:  477 x 268 mm
(II) dovefb(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) dovefb(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
(II) dovefb(0): Serial No: ZQ01547000996
(II) dovefb(0): Monitor name: PHL 227E6
(II) dovefb(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 170 MHz
(II) dovefb(0): EDID (in hex):
(II) dovefb(0): 	00ffffffffffff00410ce5c0e4030000
(II) dovefb(0): 	2f19010380301b782ae7e5a5564da125
(II) dovefb(0): 	0f5054bd4b00d1c09500950fb30081c0
(II) dovefb(0): 	818001010101023a801871382d40582c
(II) dovefb(0): 	4500dd0c1100001e000000ff005a5130
(II) dovefb(0): 	31353437303030393936000000fc0050
(II) dovefb(0): 	484c2032323745360a202020000000fd
(II) dovefb(0): 	00384c1e5311000a2020202020200021
(II) dovefb(0): EDID vendor "PHL", prod id 49381
(II) dovefb(0): Using hsync ranges from config file
(II) dovefb(0): Using vrefresh ranges from config file
(II) dovefb(0): Printing DDC gathered Modelines:
(II) dovefb(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) dovefb(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) dovefb(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) dovefb(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) dovefb(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) dovefb(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) dovefb(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) dovefb(0): Modeline "1920x1080"x60.0  172.80  1920 2040 2248 2576  1080 1081 1084 1118 -hsync +vsync (67.1 kHz)
(II) dovefb(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) dovefb(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) dovefb(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) dovefb(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz)
(II) dovefb(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) dovefb(0): EDID vendor "PHL", prod id 49381
(II) dovefb(0): mrvl_additional_quirk: vendor = PHL
(II) dovefb(0): Digital Display Input.
(II) dovefb(0): Use EDID modes for output [0x15e798], printing all modes:
(II) dovefb(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) dovefb(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) dovefb(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) dovefb(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) dovefb(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) dovefb(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) dovefb(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) dovefb(0): Modeline "1920x1080"x60.0  172.80  1920 2040 2248 2576  1080 1081 1084 1118 -hsync +vsync (67.1 kHz)
(II) dovefb(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) dovefb(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) dovefb(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) dovefb(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz)
(II) dovefb(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) dovefb(0): Not using mode "1920x1080" (bad mode clock/interlace/doublescan)
(II) dovefb(0): Printing probed modes for output lvds
(II) dovefb(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) dovefb(0): Modeline "1680x1050"x59.9  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) dovefb(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) dovefb(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) dovefb(0): Modeline "1440x900"x75.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) dovefb(0): Modeline "1440x900"x59.9   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) dovefb(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz)
(II) dovefb(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) dovefb(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) dovefb(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) dovefb(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) dovefb(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
(II) dovefb(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) dovefb(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) dovefb(0): enter mrvl_detect_edid, there are 2 crtc, output 1
(II) dovefb(0): *#* output<1> is digital.
(WW) dovefb(0): *#* output1 get digital input
(II) dovefb(0): monitor id: <Primary Monitor>
(II) dovefb(0): OPTION_ENABLE in config file = 1.
(II) dovefb(0): OPTION_NoDDCValue not define
(II) dovefb(0): In output 1, has monitor-lvds, has monitor-VGA in device section in xorg.conf.
(II) dovefb(0): *** dual display mode is disabled.
(II) dovefb(0): *#** (*pConnectStatus[0])=1
(II) dovefb(0): *#** (*pConnectStatus[1])=0
(II) dovefb(0): EDID for output VGA
(II) dovefb(0): Output lvds enabled by config file
(II) dovefb(0): Output VGA enabled by config file
(II) dovefb(0): Using sloppy heuristic for initial modes
(II) dovefb(0): Output lvds using initial mode 1920x1080
(EE) dovefb(0): Output VGA enabled but has no modes
(II) dovefb(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
(**) dovefb(0): Display dimensions: (480, 270) mm
(**) dovefb(0): DPI set to (101, 180)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(II) dovefb(0): Leave PreInit 
(==) Depth 24 pixmap format is 32 bpp
(II) dovefb(0): Enter into FBDevScreenInit
(II) dovefb(0): frame buffer linear address: 0x404cd000, physical address : 14000000
(WW) dovefb(0): Render extension initialisation successful
(II) dovefb(0): Render extension subpixel order is RGB
(==) dovefb(0): Backing store disabled
(**) dovefb(0): DPMS enabled
(II) dovefb(0): Initializing Vivante Hal
(II) dovefb(0): Initialize vivante Hal objects successfully
(II) dovefb(0): Initialize vivnate hal module successfully
(**) dovefb(0): EXA is disabled 
(II) dovefb(0): Dovefb is setting up xv adapter.
(II) dovefb(0): Initializing xv adapter.
(II) dovefb(0): Allocate mixed overly adaptor OK.
(II) dovefb(0): Set up mixed video adaptor
(II) dovefb(0): detecting xv devices.
(II) dovefb(0): try to open </dev/fb1>
(II) dovefb(0): get </dev/fb1> FSCREENINFO.
(II) dovefb(0): check </dev/fb1> is video layer -- [Video Layer 0].
(II) dovefb(0): map </dev/fb1> frame buffer.
(II) dovefb(0): map </dev/fb1> mmio.
(II) dovefb(0): mmap /dev/fb1 mmio to 0x40027000
(II) dovefb(0): try to open </dev/fb3>
(II) dovefb(0): get </dev/fb3> FSCREENINFO.
(II) dovefb(0): check </dev/fb3> is video layer -- [Video Layer 1].
(II) dovefb(0): map </dev/fb3> frame buffer.
(II) dovefb(0): map </dev/fb3> mmio.
(II) dovefb(0): mmap /dev/fb3 mmio to 0x40028000
(II) dovefb(0): resource checking okay.
(II) dovefb(0): Initializing xv adapter.
(II) dovefb(0): Allocate xv adaptor OK.
(II) dovefb(0): Set up overlay video adaptor
(EE) dovefb(0): mrvlFencePoolInit: virtual address 0x494d5000, physical address 38000000
(II) dovefb(0): Set up textured video adaptor
(II) dovefb(0): Register GPU Xv first.
(II) dovefb(0): Dovefb xv has been set up successfully.
(II) dovefb(0): Xv acceleration is loaded successfully
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_dpms
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_crtc_dpms, mode 3
(II) dovefb(0): mrvl_crtc_config: crtc [0x15dd58] get fscreeninfo successfully
(II) dovefb(0): turn off crct1
(II) dovefb(0): entering into mrvl_crtc_lock
(II) dovefb(0): entering into mrvl_mode_fixup
(II) dovefb(0): entering into mrvl_crtc_mode_fixup, orig: width 1920, height 1080, ajust: width 1920, height 1080
(II) dovefb(0): entering into mrvl_mode_prepare
(II) dovefb(0): entering into mrvl_crtc_mode_prepare
(II) dovefb(0): mrvl_crtc_config: crtc [0x15d318] get fscreeninfo successfully
(II) dovefb(0): turn on crtc0
(II) dovefb(0): set mode_set x=0, y=0
(II) dovefb(0): LCD0 crtc mode = <1920x1080>, desired mode <1920x1080>
(II) dovefb(0): entering into mrvl_mode_set, width 1920 height 1080 ajust width 1920 height 1080
(II) dovefb(0): mrvl_output.c: mrvl_check_current_pos()
(II) dovefb(0): Enter mrvl_output_get_fb_info()
(II) dovefb(0): Open fb for CRTC0 [0x15d318] successfully
(II) dovefb(0): Expecting pScrn BPP=32 & Depth=24
(II) dovefb(0): current output BPP=32 & Depth=32
(II) dovefb(0): New output setting BPP=32 & Depth=24 rgba: 8/16, 8/8, 8/0, 0/0
(II) dovefb(0): Enter mrvl_output_get_fb_info()
(II) dovefb(0): Open fb for CRTC0 [0x15d318] successfully
(II) dovefb(0): switch to <1920x1080>....
(II) dovefb(0): New setting has been applied.
(II) dovefb(0): LCD0 probed mode = <1920x1080>, <0x0>
(II) dovefb(0): Enter mrvl_output_get_fb_info()
(II) dovefb(0): Open fb for CRTC0 [0x15d318] successfully
(II) dovefb(0): entering into mrvl_crtc_gamma_set
(II) dovefb(0): entering into mrvl_crtc_mode_commit
(II) dovefb(0): entering into mrvl_mode_commit
(II) dovefb(0): entering into mrvl_crtc_unlock
(II) dovefb(0): entering into mrvl_dpms
(II) dovefb(0): entering into mrvl_crtc_dpms, mode 3
(II) dovefb(0): mrvl_crtc_config: crtc [0x15dd58] get fscreeninfo successfully
(II) dovefb(0): turn off crct1
(II) dovefb(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) dovefb(0): entering into mrvl_create_resource
(II) dovefb(0): entering into mrvl_create_resource
(II) dovefb(0): Leave FBDevScreenInit().
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
(II) AIGLX: Screen 0 is not DRI capable
(EE) AIGLX error: dlopen of /usr/lib/dri/swrast_dri.so failed (/usr/lib/dri/swrast_dri.so: cannot open shared object file: No such file or directory)
(EE) GLX: could not load software renderer
(II) GLX: no usable GL providers found for screen 0
(II) dovefb(0): Setting screen physical size to 508 x 285
(II) dovefb(0): MRVLCRTCResize: width 1920, height 1080 display pitch 1920, screen width 1920, screen height 1080, on scr pix: 0x182108, width 1920, height 1920, pitch 7680
(II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
(**) Option "CoreKeyboard"
(**) Generic Keyboard: always reports core events
(**) Generic Keyboard: Device: "/dev/input/evdev-kbd"
(EE) Unable to open evdev device "/dev/input/evdev-kbd".
(II) UnloadModule: "evdev"
(EE) PreInit returned NULL for "Generic Keyboard"
(II) config/udev: Adding input device t5335_power_key (/dev/input/event0)
(**) t5335_power_key: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) t5335_power_key: always reports core events
(**) t5335_power_key: Device: "/dev/input/event0"
(II) t5335_power_key: Found keys
(II) t5335_power_key: Configuring as keyboard
(II) XINPUT: Adding extended input device "t5335_power_key" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_variant" "wincompat"
(**) Option "xkb_options" "srvrkeys:none"
(II) XKB: reuse xkmfile /var/lib/xkb/server-A251D3D21BCF0B5515FF60E5A5D9C82886AA5316.xkm
(II) config/udev: Adding input device PixArt Microsoft USB Optical Mouse (/dev/input/mouse0)
(**) PixArt Microsoft USB Optical Mouse: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) PixArt Microsoft USB Optical Mouse: always reports core events
(**) PixArt Microsoft USB Optical Mouse: Device: "/dev/input/mouse0"
(II) UnloadModule: "evdev"
(EE) PreInit returned NULL for "PixArt Microsoft USB Optical Mouse"
(II) config/udev: Adding input device PixArt Microsoft USB Optical Mouse (/dev/input/event2)
(**) PixArt Microsoft USB Optical Mouse: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) PixArt Microsoft USB Optical Mouse: always reports core events
(**) PixArt Microsoft USB Optical Mouse: Device: "/dev/input/event2"
(II) PixArt Microsoft USB Optical Mouse: Found 3 mouse buttons
(II) PixArt Microsoft USB Optical Mouse: Found scroll wheel(s)
(II) PixArt Microsoft USB Optical Mouse: Found relative axes
(II) PixArt Microsoft USB Optical Mouse: Found x and y relative axes
(II) PixArt Microsoft USB Optical Mouse: Configuring as mouse
(**) PixArt Microsoft USB Optical Mouse: YAxisMapping: buttons 4 and 5
(**) PixArt Microsoft USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "PixArt Microsoft USB Optical Mouse" (type: MOUSE)
(II) PixArt Microsoft USB Optical Mouse: initialized for relative axes.
(II) XKB: reuse xkmfile /var/lib/xkb/server-493B8CE3BF0591994B7FE65B8594620F77B93ED8.xkm
(II) config/udev: Adding input device PixArt Microsoft USB Optical Mouse (/dev/input/mouse0)
(**) PixArt Microsoft USB Optical Mouse: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) PixArt Microsoft USB Optical Mouse: always reports core events
(**) PixArt Microsoft USB Optical Mouse: Device: "/dev/input/mouse0"
(II) UnloadModule: "evdev"
(EE) PreInit returned NULL for "PixArt Microsoft USB Optical Mouse"
(WW) config/udev: device PixArt Microsoft USB Optical Mouse already added. Ignoring.
(II) XKB: reuse xkmfile /var/lib/xkb/server-493B8CE3BF0591994B7FE65B8594620F77B93ED8.xkm
(II) config/udev: Adding input device CHICONY USB Keyboard (/dev/input/event1)
(**) CHICONY USB Keyboard: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) CHICONY USB Keyboard: always reports core events
(**) CHICONY USB Keyboard: Device: "/dev/input/event1"
(II) CHICONY USB Keyboard: Found keys
(II) CHICONY USB Keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "CHICONY USB Keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_variant" "wincompat"
(**) Option "xkb_options" "srvrkeys:none"
(II) XKB: reuse xkmfile /var/lib/xkb/server-493B8CE3BF0591994B7FE65B8594620F77B93ED8.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-493B8CE3BF0591994B7FE65B8594620F77B93ED8.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-A251D3D21BCF0B5515FF60E5A5D9C82886AA5316.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-A251D3D21BCF0B5515FF60E5A5D9C82886AA5316.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-7396D2A61791D8E37250BAD014B8EE9AFB8F9919.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-7396D2A61791D8E37250BAD014B8EE9AFB8F9919.xkm
Re: Debian on HP Thin Client T5335z
September 06, 2018 03:09PM
Thanks Koen! very useful info to cross refererence with GPL. Now I might not need to boot stock to find stuff :)

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 06, 2018 03:18PM
Hi bodhi,

the post from Rayknight points to the HP ftp server. The following file may be of interest to you since it seems to contain the patches of the stock kernel.

ftp://ftp.hp.com/pub/tcdebian/pool/thinpro42/source/linux-2.6.32.9_patches.tar.gz

There also is a different more recent uboot archive file in the same folder:

ftp://ftp.hp.com/pub/tcdebian/pool/thinpro42/source/u-boot-2010.06-psp04.04.00.01.tar.bz2

Koen



Edited 2 time(s). Last edit at 09/06/2018 03:27PM by Koen.
Re: Debian on HP Thin Client T5335z
September 06, 2018 04:12PM
rayknight Wrote:
-------------------------------------------------------
> I don't have time to look at this now, but if you
> want the u-boot source it can be found at
> ftp://ftp.hp.com/pub/tcdebian/pool/thinpro40/source/uboot-t5335z.tgz.
> There may be other interesting source files
> located in that same directory. Good news is it
> seems to be based on a more modern u-boot 2009.08.


Thanks Ray! That was very useful.

======

As usual when looking at GPL code, I want to curse :) even with open source, they made life a little harder for us (to have to decipher a few things before understanding why a bit is set and what it does).

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 06, 2018 08:10PM
Koen Wrote:
> There also is a different more recent uboot
> archive file in the same folder:
>
> ftp://ftp.hp.com/pub/tcdebian/pool/thinpro42/source/u-boot-2010.06-psp04.04.00.01.tar.bz2
>
>
That's actually the u-boot source for the HP t410 which uses a TI ARM chip similar to the Beaglebone.
Re: Debian on HP Thin Client T5335z
September 07, 2018 02:22AM
@Koen

can you extract the following file and post here for safe keeping

"/etc/X11/xorg.conf"


there look to be a few static linked modules as well as kernel modules we MAY be able to nab.
Re: Debian on HP Thin Client T5335z
September 07, 2018 05:49AM
@bodhi - Im "brain farting" as i have 5 minutes spare at my desk

i think we will need to have this module generated when you do your run time build "fbdevhw"

also if i remember correctly we added fbcon to /etc/initramfs-tools/modules initialise the console output. so we should look there to enable console outputs etc

The graphics in xorg seem to driven by xf86-video-armada http://git.arm.linux.org.uk/cgit/xf86-video-armada.git/tree/README?h=unstable-devel
and this supports the following
Freescale i.MX
Marvell Armada 510 (Dove)
and GPU drivers:
Vivante libGAL (Armada only)
Etnaviv (Armada and i.MX) with galcore kernel driver
Etnaviv (Armada and i.MX) with etnaviv DRM kernel driver

So I wonder if anyone on here would be able to take up a conversation with the chaps over at LAKKA http://www.lakka.tv/get/linux/ as they have a Cubox system running already utilising the iMX chip and i believe the marvel graphics driver


Edit : added link to same chip as the one used over at Archlinuxarm
https://archlinuxarm.org/platforms/armv7/marvell/cubox



Edited 1 time(s). Last edit at 09/07/2018 06:09AM by Gravelrash.
Attachments:
open | download - 52529f1be34e242f50ea9d16.pdf (384.9 KB)
Re: Debian on HP Thin Client T5335z
September 07, 2018 04:19PM
GPIO button

There is a "USB-recover" button. This button will trigger the USB recovery during stock u-boot booting.

Do we know where is this button? the only one that I can see outside the case is the Power button.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 07, 2018 05:10PM
Gravelrash Wrote:
-------------------------------------------------------
> @Koen
>
> can you extract the following file and post here
> for safe keeping
>
> "/etc/X11/xorg.conf"
>
>
> there look to be a few static linked modules as
> well as kernel modules we MAY be able to nab.

I'll do that on Monday when I'm back home.

@bodhi

I think I saw a small metal square with a white button on the board but can't remember where. Will have another look on Monday if nobody else has found it before then.
Re: Debian on HP Thin Client T5335z
September 08, 2018 05:22PM
I've uploaded new DTB and DTS in this instruction:

https://forum.doozan.com/read.php?2,66989,67269#msg-67269

This now has power off working properly.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Debian on HP Thin Client T5335z
September 09, 2018 02:04PM
@bodhi I mixed up different thin clients. couldn't find a button in the HP T5335Z. I did buy what looked like another Dell Wyse T10 from ebay but it was a TX0D and that has a button on the board (and uses a different CPU than the T10 / T50)

@Gravelrash below some files which may provide useful info to get graphics working.

Koen


/etc/X11/xorg.conf

Section "InputDevice"
	Identifier	"Generic Keyboard"
        Option          "XLeds" "1 2 3"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option	"XkbModel"	"evdev"
	Option	"XkbLayout"	"us"
	Option	"XkbVariant"	"wincompat"
	Option  "XkbOptions"	"srvrkeys:none"
	Driver		"evdev" 
	Option		"Device"	"/dev/input/evdev-kbd" 
EndSection
Section "Monitor"
	Identifier	"Primary Monitor"
	Option		"DPMS" 	"true"
	Option	"Enable"	"TRUE" 
	HorizSync	1-10000
	VertRefresh	1-10000
	Option		"Rotate"	"Normal" 
EndSection
Section "Device"
	Identifier	"Driver0"
	Screen		0
	Driver		"dovefb"	 
	Option		"ShadowFB" "FALSE" 
	Option		"UseGPU" "FALSE" 
	Option		"ExaAccel" "FALSE" 
	Option		"Solid" "TRUE" 
	Option		"Copy" "TRUE" 
	Option		"Composite" "FALSE" 
	Option		"SWSolid" "FALSE" 
	Option		"SWCopy" "FALSE" 
	Option		"Commit" "FALSE" 
	Option		"XvAccel" "TRUE" 
	Option		"HWCursor" "FALSE" 
	Option		"UseDriverBuiltInMode" "TRUE" 
	Option		"EncFunc" "0x0b"
	Option		"Monitor-lvds"	"Primary Monitor" 
	Option		"Monitor-vga"	"Primary Monitor" 
	Option		"EnableDualDisplay" "false"
EndSection
Section "Screen"
	Device		"Driver0"
	Monitor		"Primary Monitor"
	Identifier	"Primary Screen"
	DefaultDepth	24
	DefaultFbBpp	32
	SubSection	"Display"
		Viewport	0 0
		Virtual	1920 1920
	EndSubSection
EndSection


/etc/X11/xorg.conf.fb1


Section "DRI"
	Mode	0666
EndSection
Section "ServerFlags"
	Option "DontVTSwitch" "true"
	Option "DontZap" "true"
	Option "DontZoom" "true"	
EndSection
Section "InputDevice"
	Identifier	"Generic Keyboard"
        Option          "XLeds" "1 2 3"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option "XkbModel"	"evdev"
	Option "XkbLayout"	"us"
	Option "XkbVariant"	"wincompat"
	Option "XkbOptions"	"srvrkeys:none"
	Driver		"evdev"
	Option		"Device"	"/dev/input/evdev-kbd" 
EndSection
Section "Monitor"
	Identifier	"Primary Monitor"
	Option		"DPMS" 	"true"
EndSection
Section "Device"
	Identifier	"Driver0"
	Screen		0
	Driver		"fbdev"
	Option "fbdev" "/dev/fb1"
EndSection
Section "Screen"
	Device		"Driver0"
	Monitor		"Primary Monitor"
	Identifier	"Primary Screen"
	DefaultDepth	24
	SubSection	"Display"
		ViewPort	0 0
	EndSubSection
EndSection


Xorg.0.log


X.Org X Server 1.7.6
Release Date: 2010-03-17
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.32.9-dove-5.3.6-1-armel armv7l Ubuntu
Current Operating System: Linux HPf4ce4625c9fa 2.6.32.9-dove-5.3.6-1-armel #1 Tue Oct 9 10:08:35 MDT 2012 armv7l
Kernel command line: mtdparts=spi0.0:768k(u-boot),8k(uboot_env),8k(pu_env),8k(hp_env) root=/dev/sda1 rw init=/init vmalloc=384M video=dovefb oldI2Cbus=1 cpufreq_disable=1 splash quiet
Build Date: 19 August 2013  11:58:13AM
xorg-server 2:1.7.6-2ubuntu7.12 (For technical support please see http://www.ubuntu.com/support) 
Current version of pixman: 0.16.4
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Sep  6 20:36:37 2018
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using config directory: "/etc/X11/xorg.conf.d"
(==) No Layout section.  Using the first Screen section.
(**) |-->Screen "Primary Screen" (0)
(**) |   |-->Monitor "Primary Monitor"
(**) |   |-->Device "Driver0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
	Entry deleted from font path.
(WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
	Entry deleted from font path.
(==) FontPath set to:
	/usr/share/fonts/X11/misc,
	built-ins
(==) ModulePath set to "/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
(==) |-->Input Device "Generic Keyboard"
(==) No Layout section. Using the first core keyboard device.
(II) The server relies on udev to provide the list of input devices.
	If no devices become available, reconfigure udev or disable AutoAddDevices.
(II) Loader magic: 0x13bf38
(II) Module ABI versions:
	X.Org ANSI C Emulation: 0.4
	X.Org Video Driver: 6.0
	X.Org XInput driver : 7.0
	X.Org Server Extension : 2.0
(++) using VT number 7

(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.13.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.1.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "dovefb"
(II) Loading /usr/lib/xorg/modules/drivers/dovefb_drv.so
(II) Module fbdev: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 0.3.0
	ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 2.3.2
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 7.0
(II) dovefb: Support Marvell LCD Controller: 88AP510
(WW) Falling back to old probe method for dovefb
(II) Loading sub module "fbdevhw"
(II) LoadModule: "fbdevhw"
(II) Loading /usr/lib/xorg/modules/linux/libfbdevhw.so
(II) Module fbdevhw: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 0.0.2
	ABI class: X.Org Video Driver, version 6.0
(II) dovefb(0): using default device
(II) dovefb(0): source version <1:0.3.4-1>
(II) Running in FRAMEBUFFER Mode
(II) dovefb(0): Enter into PreInit
(II) dovefb(0): ioctl FBIOGET_VSCREENINFO
(**) dovefb(0): Depth 24, (**) framebuffer bpp 32
(==) dovefb(0): RGB weight 888
(==) dovefb(0): Default visual is TrueColor
(==) dovefb(0): Using gamma correction (1.0, 1.0, 1.0)
(II) dovefb(0): hardware: GFX Layer 0 (video memory: 49152kB)
(**) dovefb(0): Option "ShadowFB" "FALSE"
(**) dovefb(0): Option "EncFunc" "0x0b"
(**) dovefb(0): Option "HWcursor" "FALSE"
(**) dovefb(0): Option "ExaAccel" "FALSE"
(**) dovefb(0): Option "XvAccel" "TRUE"
(**) dovefb(0): Option "Solid" "TRUE"
(**) dovefb(0): Option "Copy" "TRUE"
(**) dovefb(0): Option "Composite" "FALSE"
(**) dovefb(0): Option "Commit" "FALSE"
(**) dovefb(0): Option "SWSolid" "FALSE"
(**) dovefb(0): Option "SWCopy" "FALSE"
(**) dovefb(0): Option "UseGPU" "FALSE"
(**) dovefb(0): Option "UseDriverBuiltInMode" "TRUE"
(**) dovefb(0): Option "EnableDualDisplay" "false"
(**) dovefb(0): enhance function is mode <11>
(II) dovefb(0): shadow fb is disabled
(II) dovefb(0): debug is disabled.
(II) dovefb(0): checking modes against framebuffer device...
(II) dovefb(0): checking modes against monitor...
(--) dovefb(0): Virtual size is 1920x1920 (pitch 1920)
(II) dovefb(0): mrvlCrtcInit: Found 2 fb devices
(II) dovefb(0): mrvlCrtcInit: crtc [0], lcd virtual x 1920, y 5760
(II) dovefb(0): mrvlCrtcInit: create crtc0.
(II) dovefb(0): mrvlCrtcInit: crtc0 has been initialized.
(II) dovefb(0): mrvlCrtcInit: crtc [1], lcd virtual x 1920, y 5760
(II) dovefb(0): mrvlCrtcInit: create crtc1.
(II) dovefb(0): mrvlCrtcInit: crtc1 has been initialized.
(II) dovefb(0): mrvlCrtcInit: completed.
(II) dovefb(0): mrvlOutputInit: create output...
(II) dovefb(0): mrvlOutputInit: create output0 at lvds...
(II) dovefb(0): Output lvds using monitor section Primary Monitor
(**) dovefb(0): Option "Enable" "TRUE"
(**) dovefb(0): Option "Rotate" "Normal"
(II) dovefb(0): mrvlOutputInit: create output1 at VGA...
(II) dovefb(0): Output VGA using monitor section Primary Monitor
(II) dovefb(0): mrvlOutputInit: Init output...
(II) dovefb(0): mrvlOutputInit: Init output0.
(II) dovefb(0): mrvlOutputInit: Init output1.
(II) dovefb(0): *** output <lvds>, x=0, y=0
(II) dovefb(0): *** output <VGA>, x=0, y=0
(II) dovefb(0): enter mrvl_detect_edid, there are 2 crtc, output 0
(II) dovefb(0): *#* output<0> is digital.
(II) dovefb(0): monitor id: <Primary Monitor>
(II) dovefb(0): OPTION_ENABLE in config file = 1.
(II) dovefb(0): OPTION_NoDDCValue not define
(II) dovefb(0): In output 0, has monitor-lvds, has monitor-VGA in device section in xorg.conf.
(II) dovefb(0): *** dual display mode is disabled.
(II) dovefb(0): *#** (*pConnectStatus[0])=1
(II) dovefb(0): *#** (*pConnectStatus[1])=1
(II) dovefb(0): mrvl_get_modes_with_edid!
(II) dovefb(0): EDID for output lvds
(II) dovefb(0): Manufacturer: PHL  Model: c0e5  Serial#: 996
(II) dovefb(0): Year: 2015  Week: 47
(II) dovefb(0): EDID Version: 1.3
(II) dovefb(0): Digital Display Input
(II) dovefb(0): Max Image Size [cm]: horiz.: 48  vert.: 27
(II) dovefb(0): Gamma: 2.20
(II) dovefb(0): DPMS capabilities: Off
(II) dovefb(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
(II) dovefb(0): First detailed timing is preferred mode
(II) dovefb(0): redX: 0.647 redY: 0.338   greenX: 0.302 greenY: 0.632
(II) dovefb(0): blueX: 0.147 blueY: 0.061   whiteX: 0.313 whiteY: 0.329
(II) dovefb(0): Supported established timings:
(II) dovefb(0): 720x400@70Hz
(II) dovefb(0): 640x480@60Hz
(II) dovefb(0): 640x480@67Hz
(II) dovefb(0): 640x480@72Hz
(II) dovefb(0): 640x480@75Hz
(II) dovefb(0): 800x600@60Hz
(II) dovefb(0): 800x600@75Hz
(II) dovefb(0): 1024x768@60Hz
(II) dovefb(0): 1024x768@75Hz
(II) dovefb(0): 1280x1024@75Hz
(II) dovefb(0): Manufacturer's mask: 0
(II) dovefb(0): Supported standard timings:
(II) dovefb(0): #0: hsize: 1920  vsize 1080  refresh: 60  vid: 49361
(II) dovefb(0): #1: hsize: 1440  vsize 900  refresh: 60  vid: 149
(II) dovefb(0): #2: hsize: 1440  vsize 900  refresh: 75  vid: 3989
(II) dovefb(0): #3: hsize: 1680  vsize 1050  refresh: 60  vid: 179
(II) dovefb(0): #4: hsize: 1280  vsize 720  refresh: 60  vid: 49281
(II) dovefb(0): #5: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
(II) dovefb(0): Supported detailed timing:
(II) dovefb(0): clock: 148.5 MHz   Image Size:  477 x 268 mm
(II) dovefb(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) dovefb(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
(II) dovefb(0): Serial No: ZQ01547000996
(II) dovefb(0): Monitor name: PHL 227E6
(II) dovefb(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 170 MHz
(II) dovefb(0): EDID (in hex):
(II) dovefb(0): 	00ffffffffffff00410ce5c0e4030000
(II) dovefb(0): 	2f19010380301b782ae7e5a5564da125
(II) dovefb(0): 	0f5054bd4b00d1c09500950fb30081c0
(II) dovefb(0): 	818001010101023a801871382d40582c
(II) dovefb(0): 	4500dd0c1100001e000000ff005a5130
(II) dovefb(0): 	31353437303030393936000000fc0050
(II) dovefb(0): 	484c2032323745360a202020000000fd
(II) dovefb(0): 	00384c1e5311000a2020202020200021
(II) dovefb(0): EDID vendor "PHL", prod id 49381
(II) dovefb(0): Using hsync ranges from config file
(II) dovefb(0): Using vrefresh ranges from config file
(II) dovefb(0): Printing DDC gathered Modelines:
(II) dovefb(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) dovefb(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) dovefb(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) dovefb(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) dovefb(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) dovefb(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) dovefb(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) dovefb(0): Modeline "1920x1080"x60.0  172.80  1920 2040 2248 2576  1080 1081 1084 1118 -hsync +vsync (67.1 kHz)
(II) dovefb(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) dovefb(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) dovefb(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) dovefb(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz)
(II) dovefb(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) dovefb(0): EDID vendor "PHL", prod id 49381
(II) dovefb(0): mrvl_additional_quirk: vendor = PHL
(II) dovefb(0): Digital Display Input.
(II) dovefb(0): Use EDID modes for output [0x15e798], printing all modes:
(II) dovefb(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) dovefb(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
(II) dovefb(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) dovefb(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) dovefb(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) dovefb(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) dovefb(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) dovefb(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) dovefb(0): Modeline "1920x1080"x60.0  172.80  1920 2040 2248 2576  1080 1081 1084 1118 -hsync +vsync (67.1 kHz)
(II) dovefb(0): Modeline "1440x900"x0.0   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) dovefb(0): Modeline "1440x900"x0.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) dovefb(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) dovefb(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz)
(II) dovefb(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) dovefb(0): Not using mode "1920x1080" (bad mode clock/interlace/doublescan)
(II) dovefb(0): Printing probed modes for output lvds
(II) dovefb(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) dovefb(0): Modeline "1680x1050"x59.9  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) dovefb(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) dovefb(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) dovefb(0): Modeline "1440x900"x75.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz)
(II) dovefb(0): Modeline "1440x900"x59.9   88.75  1440 1488 1520 1600  900 903 909 926 +hsync -vsync (55.5 kHz)
(II) dovefb(0): Modeline "1280x720"x60.0   74.48  1280 1336 1472 1664  720 721 724 746 -hsync +vsync (44.8 kHz)
(II) dovefb(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) dovefb(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) dovefb(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) dovefb(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) dovefb(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) dovefb(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
(II) dovefb(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) dovefb(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) dovefb(0): enter mrvl_detect_edid, there are 2 crtc, output 1
(II) dovefb(0): *#* output<1> is digital.
(WW) dovefb(0): *#* output1 get digital input
(II) dovefb(0): monitor id: <Primary Monitor>
(II) dovefb(0): OPTION_ENABLE in config file = 1.
(II) dovefb(0): OPTION_NoDDCValue not define
(II) dovefb(0): In output 1, has monitor-lvds, has monitor-VGA in device section in xorg.conf.
(II) dovefb(0): *** dual display mode is disabled.
(II) dovefb(0): *#** (*pConnectStatus[0])=1
(II) dovefb(0): *#** (*pConnectStatus[1])=0
(II) dovefb(0): EDID for output VGA
(II) dovefb(0): Output lvds enabled by config file
(II) dovefb(0): Output VGA enabled by config file
(II) dovefb(0): Using sloppy heuristic for initial modes
(II) dovefb(0): Output lvds using initial mode 1920x1080
(EE) dovefb(0): Output VGA enabled but has no modes
(II) dovefb(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
(**) dovefb(0): Display dimensions: (480, 270) mm
(**) dovefb(0): DPI set to (101, 180)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 1.7.6, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(II) dovefb(0): Leave PreInit 
(==) Depth 24 pixmap format is 32 bpp
(II) dovefb(0): Enter into FBDevScreenInit
(II) dovefb(0): frame buffer linear address: 0x404cd000, physical address : 14000000
(WW) dovefb(0): Render extension initialisation successful
(II) dovefb(0): Render extension subpixel order is RGB
(==) dovefb(0): Backing store disabled
(**) dovefb(0): DPMS enabled
(II) dovefb(0): Initializing Vivante Hal
(II) dovefb(0): Initialize vivante Hal objects successfully
(II) dovefb(0): Initialize vivnate hal module successfully
(**) dovefb(0): EXA is disabled 
(II) dovefb(0): Dovefb is setting up xv adapter.
(II) dovefb(0): Initializing xv adapter.
(II) dovefb(0): Allocate mixed overly adaptor OK.
(II) dovefb(0): Set up mixed video adaptor
(II) dovefb(0): detecting xv devices.
(II) dovefb(0): try to open </dev/fb1>
(II) dovefb(0): get </dev/fb1> FSCREENINFO.
(II) dovefb(0): check </dev/fb1> is video layer -- [Video Layer 0].
(II) dovefb(0): map </dev/fb1> frame buffer.
(II) dovefb(0): map </dev/fb1> mmio.
(II) dovefb(0): mmap /dev/fb1 mmio to 0x40027000
(II) dovefb(0): try to open </dev/fb3>
(II) dovefb(0): get </dev/fb3> FSCREENINFO.
(II) dovefb(0): check </dev/fb3> is video layer -- [Video Layer 1].
(II) dovefb(0): map </dev/fb3> frame buffer.
(II) dovefb(0): map </dev/fb3> mmio.
(II) dovefb(0): mmap /dev/fb3 mmio to 0x40028000
(II) dovefb(0): resource checking okay.
(II) dovefb(0): Initializing xv adapter.
(II) dovefb(0): Allocate xv adaptor OK.
(II) dovefb(0): Set up overlay video adaptor
(EE) dovefb(0): mrvlFencePoolInit: virtual address 0x494d5000, physical address 38000000
(II) dovefb(0): Set up textured video adaptor
(II) dovefb(0): Register GPU Xv first.
(II) dovefb(0): Dovefb xv has been set up successfully.
(II) dovefb(0): Xv acceleration is loaded successfully
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_dpms
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_get_crtc
(II) dovefb(0): entering into mrvl_crtc_dpms, mode 3
(II) dovefb(0): mrvl_crtc_config: crtc [0x15dd58] get fscreeninfo successfully
(II) dovefb(0): turn off crct1
(II) dovefb(0): entering into mrvl_crtc_lock
(II) dovefb(0): entering into mrvl_mode_fixup
(II) dovefb(0): entering into mrvl_crtc_mode_fixup, orig: width 1920, height 1080, ajust: width 1920, height 1080
(II) dovefb(0): entering into mrvl_mode_prepare
(II) dovefb(0): entering into mrvl_crtc_mode_prepare
(II) dovefb(0): mrvl_crtc_config: crtc [0x15d318] get fscreeninfo successfully
(II) dovefb(0): turn on crtc0
(II) dovefb(0): set mode_set x=0, y=0
(II) dovefb(0): LCD0 crtc mode = <1920x1080>, desired mode <1920x1080>
(II) dovefb(0): entering into mrvl_mode_set, width 1920 height 1080 ajust width 1920 height 1080
(II) dovefb(0): mrvl_output.c: mrvl_check_current_pos()
(II) dovefb(0): Enter mrvl_output_get_fb_info()
(II) dovefb(0): Open fb for CRTC0 [0x15d318] successfully
(II) dovefb(0): Expecting pScrn BPP=32 & Depth=24
(II) dovefb(0): current output BPP=32 & Depth=32
(II) dovefb(0): New output setting BPP=32 & Depth=24 rgba: 8/16, 8/8, 8/0, 0/0
(II) dovefb(0): Enter mrvl_output_get_fb_info()
(II) dovefb(0): Open fb for CRTC0 [0x15d318] successfully
(II) dovefb(0): switch to <1920x1080>....
(II) dovefb(0): New setting has been applied.
(II) dovefb(0): LCD0 probed mode = <1920x1080>, <0x0>
(II) dovefb(0): Enter mrvl_output_get_fb_info()
(II) dovefb(0): Open fb for CRTC0 [0x15d318] successfully
(II) dovefb(0): entering into mrvl_crtc_gamma_set
(II) dovefb(0): entering into mrvl_crtc_mode_commit
(II) dovefb(0): entering into mrvl_mode_commit
(II) dovefb(0): entering into mrvl_crtc_unlock
(II) dovefb(0): entering into mrvl_dpms
(II) dovefb(0): entering into mrvl_crtc_dpms, mode 3
(II) dovefb(0): mrvl_crtc_config: crtc [0x15dd58] get fscreeninfo successfully
(II) dovefb(0): turn off crct1
(II) dovefb(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) dovefb(0): entering into mrvl_create_resource
(II) dovefb(0): entering into mrvl_create_resource
(II) dovefb(0): Leave FBDevScreenInit().
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
(II) AIGLX: Screen 0 is not DRI capable
(EE) AIGLX error: dlopen of /usr/lib/dri/swrast_dri.so failed (/usr/lib/dri/swrast_dri.so: cannot open shared object file: No such file or directory)
(EE) GLX: could not load software renderer
(II) GLX: no usable GL providers found for screen 0
(II) dovefb(0): Setting screen physical size to 508 x 285
(II) dovefb(0): MRVLCRTCResize: width 1920, height 1080 display pitch 1920, screen width 1920, screen height 1080, on scr pix: 0x182108, width 1920, height 1920, pitch 7680
(II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
(**) Option "CoreKeyboard"
(**) Generic Keyboard: always reports core events
(**) Generic Keyboard: Device: "/dev/input/evdev-kbd"
(EE) Unable to open evdev device "/dev/input/evdev-kbd".
(II) UnloadModule: "evdev"
(EE) PreInit returned NULL for "Generic Keyboard"
(II) config/udev: Adding input device t5335_power_key (/dev/input/event0)
(**) t5335_power_key: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) t5335_power_key: always reports core events
(**) t5335_power_key: Device: "/dev/input/event0"
(II) t5335_power_key: Found keys
(II) t5335_power_key: Configuring as keyboard
(II) XINPUT: Adding extended input device "t5335_power_key" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_variant" "wincompat"
(**) Option "xkb_options" "srvrkeys:none"
(II) XKB: reuse xkmfile /var/lib/xkb/server-A251D3D21BCF0B5515FF60E5A5D9C82886AA5316.xkm
(II) config/udev: Adding input device PixArt Microsoft USB Optical Mouse (/dev/input/mouse0)
(**) PixArt Microsoft USB Optical Mouse: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) PixArt Microsoft USB Optical Mouse: always reports core events
(**) PixArt Microsoft USB Optical Mouse: Device: "/dev/input/mouse0"
(II) UnloadModule: "evdev"
(EE) PreInit returned NULL for "PixArt Microsoft USB Optical Mouse"
(II) config/udev: Adding input device PixArt Microsoft USB Optical Mouse (/dev/input/event2)
(**) PixArt Microsoft USB Optical Mouse: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) PixArt Microsoft USB Optical Mouse: always reports core events
(**) PixArt Microsoft USB Optical Mouse: Device: "/dev/input/event2"
(II) PixArt Microsoft USB Optical Mouse: Found 3 mouse buttons
(II) PixArt Microsoft USB Optical Mouse: Found scroll wheel(s)
(II) PixArt Microsoft USB Optical Mouse: Found relative axes
(II) PixArt Microsoft USB Optical Mouse: Found x and y relative axes
(II) PixArt Microsoft USB Optical Mouse: Configuring as mouse
(**) PixArt Microsoft USB Optical Mouse: YAxisMapping: buttons 4 and 5
(**) PixArt Microsoft USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "PixArt Microsoft USB Optical Mouse" (type: MOUSE)
(II) PixArt Microsoft USB Optical Mouse: initialized for relative axes.
(II) XKB: reuse xkmfile /var/lib/xkb/server-493B8CE3BF0591994B7FE65B8594620F77B93ED8.xkm
(II) config/udev: Adding input device PixArt Microsoft USB Optical Mouse (/dev/input/mouse0)
(**) PixArt Microsoft USB Optical Mouse: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) PixArt Microsoft USB Optical Mouse: always reports core events
(**) PixArt Microsoft USB Optical Mouse: Device: "/dev/input/mouse0"
(II) UnloadModule: "evdev"
(EE) PreInit returned NULL for "PixArt Microsoft USB Optical Mouse"
(WW) config/udev: device PixArt Microsoft USB Optical Mouse already added. Ignoring.
(II) XKB: reuse xkmfile /var/lib/xkb/server-493B8CE3BF0591994B7FE65B8594620F77B93ED8.xkm
(II) config/udev: Adding input device CHICONY USB Keyboard (/dev/input/event1)
(**) CHICONY USB Keyboard: Applying InputClass "Generic Keyboard"
(**) Option "CoreKeyboard"
(**) CHICONY USB Keyboard: always reports core events
(**) CHICONY USB Keyboard: Device: "/dev/input/event1"
(II) CHICONY USB Keyboard: Found keys
(II) CHICONY USB Keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "CHICONY USB Keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_variant" "wincompat"
(**) Option "xkb_options" "srvrkeys:none"
(II) XKB: reuse xkmfile /var/lib/xkb/server-493B8CE3BF0591994B7FE65B8594620F77B93ED8.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-493B8CE3BF0591994B7FE65B8594620F77B93ED8.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-A251D3D21BCF0B5515FF60E5A5D9C82886AA5316.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-A251D3D21BCF0B5515FF60E5A5D9C82886AA5316.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-7396D2A61791D8E37250BAD014B8EE9AFB8F9919.xkm
(II) XKB: reuse xkmfile /var/lib/xkb/server-7396D2A61791D8E37250BAD014B8EE9AFB8F9919.xkm

Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: