Debian Stretch on Sata disk in WD MyCloud EX2 Ultra
Posted by LinAdmin
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 25, 2022 03:24PM |
Registered: 7 months ago Posts: 142 |
Thanks, but....
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> setenv fdt_skip_update yes
Marvell>> setenv bootargs root=/dev/sda2 console=ttyS0,115200 earlyprintk=serial
Marvell>> fatload usb 0:1 0x02000000 uimage
reading uimage
5236606 bytes read in 226 ms (22.1 MiB/s)
Marvell>> bootm 0x02000000
## Booting image at 02000000 ...
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.13.8-mvebu-tld-1
Created: 2022-11-25 9:49:59 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5236542 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 25, 2022 04:07PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js,
Strange!
I guess you should
1. Try booting with tftp. Just load the uImage over from tftp and boot the same way.
2. Read the Ex2 Ultra thread to see if others found anything weird like this: https://forum.doozan.com/read.php?2,99079
-bodhi
===========================
Forum Wiki
bodhi's corner
Strange!
I guess you should
1. Try booting with tftp. Just load the uImage over from tftp and boot the same way.
2. Read the Ex2 Ultra thread to see if others found anything weird like this: https://forum.doozan.com/read.php?2,99079
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 26, 2022 01:50AM |
Registered: 7 months ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 26, 2022 10:45AM |
Registered: 7 months ago Posts: 142 |
@bodhi, you are a fucking genius!!!
Edited 3 time(s). Last edit at 11/26/2022 11:33AM by i5Js.
Marvell>> setenv fdt_skip_update yes
Marvell>> setenv bootargs console=ttyS0,115200 root=/dev/sda2
Marvell>> setenv ipaddr 192.168.1.110; setenv serverip 192.168.1.23; tftp 0x02000000
*** Warning: no boot file name; using 'C0A8016E.img'
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'C0A8016E.img'.
Load address: 0x2000000
Loading: *
TFTP error: 'File not found' (1)
Not retrying...
Marvell>> setenv ipaddr 192.168.1.110; setenv serverip 192.168.1.23; tftp 0x02000000 uimage
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'uimage'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#####
425.8 KiB/s
done
Bytes transferred = 3886355 (3b4d13 hex)
Marvell>> bootm 0x2000000
## Booting image at 02000000 ...
## Booting kernel from Legacy Image at 02000000 ...
Image Name: WDMC-Gen2
Created: 2022-11-23 15:00:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3886291 Bytes = 3.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
DTB:0x003B8540 (0x00004793)
C:0x000080E0-0x003BCD20->0x00C7C400-0x01031040
DTB:0x0102C860 (0x000047CC)
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 5.15.79 (root@virtsrv) (arm-none-eabi-gcc (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027], GNU ld (2.35.2-2+14+b2) 2.35.2) #1 SMP Wed Nov 23 15:27:2
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: WD MyCloud Ex2 Ultra
Memory policy: Data cache writealloc
Zone ranges:
Normal [mem 0x0000000000000000-0x000000002fffffff]
HighMem [mem 0x0000000030000000-0x000000003fffffff]
Edited 3 time(s). Last edit at 11/26/2022 11:33AM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 26, 2022 10:45AM |
Registered: 7 months ago Posts: 142 |
lMovable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000003fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] percpu: Embedded 11 pages/cpu s14028 r8192 d22836 u45056 Built 1 zonelists, mobility grouping on. Total pages: 260416 Kernel command line: console=ttyS0,115200 root=/dev/sda2 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 1026284K/1048576K available (7650K kernel code, 494K rwdata, 1916K rodata, 1024K init, 335K bss, 22292K reserved, 0K cma-reserved, 262144K highmem) rcu: Hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 D prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns Switching to timer-based delay loop, resolution 1ns Ignoring duplicate/late registration of read_current_timer delay clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: Spectre v2: using BPIALL workaround CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 mvebu-pmsu: Initializing Power Management Service Unit rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... Booting CPU 1 CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU1: Spectre v2: using BPIALL workaround smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (2664.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered PF_NETLINK/PF_ROUTE protocol family DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' cpuidle: using governor ladder mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling cryptd: max_cpu_qlen set to 1000 raid6: neonx8 gen() 592 MB/s raid6: neonx8 xor() 502 MB/s raid6: neonx4 gen() 1694 MB/s raid6: neonx4 xor() 1122 MB/s raid6: neonx2 gen() 2071 MB/s raid6: neonx2 xor() 1328 MB/s raid6: neonx1 gen() 1751 MB/s raid6: neonx1 xor() 1164 MB/s raid6: int32x8 gen() 244 MB/s raid6: int32x8 xor() 170 MB/s raid6: int32x4 gen() 280 MB/s raid6: int32x4 xor() 180 MB/s raid6: int32x2 gen() 449 MB/s raid6: int32x2 xor() 236 MB/s raid6: int32x1 gen() 512 MB/s raid6: int32x1 xor() 196 MB/s raid6: using algorithm neonx2 gen() 2071 MB/s raid6: .... xor() 1328 MB/s, rmw enabled raid6: using neon recovery algorithm SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered clocksource: Switched to clocksource arm_global_timer VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) FS-Cache: Loaded CacheFiles: Loaded NET: Registered PF_INET protocol family IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) TCP: Hash tables configured (established 8192 bind 8192) UDP hash table entries: 512 (order: 2, 16384 bytes, linear) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Initialise system trusted keyrings workingset: timestamp_bits=14 max_order=18 bucket_order=4 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). FS-Cache: Netfs 'cifs' registered for caching Key type cifs.idmap registered ksmbd: The ksmbd server is experimental, use at your own risk. ntfs3: Max link count 4000 ntfs3: Read-only LZX/Xpress compression included xor: measuring software checksum speed arm4regs : 2172 MB/sec 8regs : 1637 MB/sec 32regs : 1733 MB/sec neon : 1598 MB/sec xor: using function: arm4regs (2172 MB/sec) async_tx: api initialized (async) Key type asymmetric registered Asymmetric key parser 'x509' registered bounce: pool size: 64 pages Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler kyber registered armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled printk: console [ttyS0] disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 12500000) is a 16550A printk: console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, base_baud = 12500000) is a 16550A brd: module loaded loop: module loaded ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi host0: ahci-mvebu scsi host1: ahci-mvebu ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 52 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 52 hwmon hwmon0: temp1_input not attached to any thermal zone mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled mvneta f1034000.ethernet eth0: Using hardware mac address 00:50:43:36:98:34 usbcore: registered new interface driver lan78xx ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 48, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 5.15.79 ehci_hcd usb usb1: SerialNumber: f1058000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver ohci-platform: OHCI generic platform driver uhci_hcd: USB Universal Host Controller Interface driver xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000 xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 5.15.79 xhci-hcd usb usb2: SerialNumber: f10f0000.usb3 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 5.15.79 xhci-hcd usb usb3: SerialNumber: f10f0000.usb3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000 xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 5.15.79 xhci-hcd usb usb4: SerialNumber: f10f8000.usb3 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: xHCI Host Controller usb usb5: Manufacturer: Linux 5.15.79 xhci-hcd usb usb5: SerialNumber: f10f8000.usb3 ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected fotg210_hcd: FOTG210 Host Controller (EHCI) Driver Warning! fotg210_hcd should always be loaded before uhci_hcd and ohci_hcd, not after SPI driver max3421-hcd has no spi_device_id for maxim,max3421 usbcore: registered new interface driver usb-storage i2c_dev: i2c /dev entries driver mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs marvell-cesa f1090000.crypto: CESA device successfully registered hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered PF_INET6 protocol family Segment Routing with IPv6 In-situ OAM (IOAM) with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered PF_PACKET protocol family Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates input: gpio-keys as /devices/platform/gpio-keys/input/input0 md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. VFS: Cannot open root device "sda2" or unknown-block(0,0): error -6 Please append a correct "root=" boot option; here are the available partitions: 0100 4096 ram0 (driver?) 0101 4096 ram1 (driver?) 0102 4096 ram2 (driver?) 0103 4096 ram3 (driver?) 0104 4096 ram4 (driver?) 0105 4096 ram5 (driver?) 0106 4096 ram6 (driver?) 0107 4096 ram7 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) CPU1: stopping CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.15.79 #1 Hardware name: Marvell Armada 380/385 (Device Tree) [<c010ddd8>] (unwind_backtrace) from [<c0109530>] (show_stack+0x10/0x14) [<c0109530>] (show_stack) from [<c086d234>] (dump_stack_lvl+0x40/0x4c) [<c086d234>] (dump_stack_lvl) from [<c010b83c>] (do_handle_IPI+0x84/0x128) [<c010b83c>] (do_handle_IPI) from [<c010b8f4>] (ipi_handler+0x14/0x20) [<c010b8f4>] (ipi_handler) from [<c0167f2c>] (handle_percpu_devid_irq+0x4c/0xe8) [<c0167f2c>] (handle_percpu_devid_irq) from [<c016320c>] (handle_irq_desc+0x24/0x34) [<c016320c>] (handle_irq_desc) from [<c016327c>] (handle_domain_irq+0x3c/0x54) [<c016327c>] (handle_domain_irq) from [<c0499e18>] (gic_handle_irq+0x70/0x80) [<c0499e18>] (gic_handle_irq) from [<c01012fc>] (__irq_svc+0x5c/0x78) Exception stack(0xc1481f68 to 0xc1481fb0) 1f60: 00000bea 00000000 00000001 c01133e0 00000000 00000000 1f80: 00000002 c0c05fcc ffffe000 c0c06010 c0b4ac70 00000000 00000000 c1481fb8 1fa0: c0106e60 c0106e50 60000013 ffffffff [<c01012fc>] (__irq_svc) from [<c0106e50>] (arch_cpu_idle+0x1c/0x38) [<c0106e50>] (arch_cpu_idle) from [<c08782bc>] (default_idle_call+0x2c/0x38) [<c08782bc>] (default_idle_call) from [<c01494ac>] (do_idle+0x10c/0x1c8) [<c01494ac>] (do_idle) from [<c0149828>] (cpu_startup_entry+0x18/0x20) [<c0149828>] (cpu_startup_entry) from [<00101c70>] (0x101c70) ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
Edited 3 time(s). Last edit at 11/26/2022 11:34AM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 26, 2022 11:22AM |
Registered: 7 months ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 26, 2022 02:27PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js,
Now try tftp the umage Linux-5.13.8-mvebu-tld-1, and boot the same way.
-bodhi
===========================
Forum Wiki
bodhi's corner
Now try tftp the umage Linux-5.13.8-mvebu-tld-1, and boot the same way.
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 26, 2022 02:31PM |
Registered: 7 months ago Posts: 142 |
Game, Set and Match!!!
Marvell>> setenv fdt_skip_update yes
Marvell>> setenv bootargs console=ttyS0,115200 root=/dev/sda2
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> setenv initrd_high 0xffffffff
Marvell>> setenv ipaddr 192.168.1.110; setenv serverip 192.168.1.23; tftp 0xa00000 uimage; tftp 0x1200000 uramdisk
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'uimage'.
Load address: 0xa00000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#####
423.8 KiB/s
done
Bytes transferred = 3886355 (3b4d13 hex)
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'uramdisk'.
Load address: 0x1200000
Loading: #################################################################
##############################################
387.7 KiB/s
done
Bytes transferred = 1622632 (18c268 hex)
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> bootm 0xa00000 0x1200000
## Booting image at 00a00000 ...
## Booting kernel from Legacy Image at 00a00000 ...
Image Name: WDMC-Gen2
Created: 2022-11-23 15:00:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3886291 Bytes = 3.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01200000 ...
Image Name: Custom initramfs
Created: 2021-07-28 7:11:31 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1622568 Bytes = 1.5 MiB
Load Address: 00e00000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
DTB:0x003B8540 (0x00004793)
C:0x000080E0-0x003BCD60->0x00C7C400-0x01031080
DTB:0x0102C860 (0x00004810)
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 5.15.79 (root@virtsrv) (arm-none-eabi-gcc (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027], GNU ld (2.35.2-2+14+b2) 2.35.2) #1 SMP Wed Nov 23 15:27:2
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: WD MyCloud Ex2 Ultra
Memory policy: Data cache writealloc
Zone ranges:
Normal [mem 0x0000000000000000-0x000000002fffffff]
HighMem [mem 0x0000000030000000-0x000000003fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000000000-0x000000003fffffff]
Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
percpu: Embedded 11 pages/cpu s14028 r8192 d22836 u45056
Built 1 zonelists, mobility grouping on. Total pages: 260416
Kernel command line: console=ttyS0,115200 root=/dev/sda2
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 1024696K/1048576K available (7650K kernel code, 494K rwdata, 1916K rodata, 1024K init, 335K bss, 23880K reserved, 0K cma-reserved, 262144K highmem)
rcu: Hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 D prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
Switching to timer-based delay loop, resolution 1ns
Ignoring duplicate/late registration of read_current_timer delay
clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
CPU: Testing write buffer coherency: ok
CPU0: Spectre v2: using BPIALL workaround
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100060
mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
mvebu-pmsu: Initializing Power Management Service Unit
rcu: Hierarchical SRCU implementation.
smp: Bringing up secondary CPUs ...
Booting CPU 1
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU1: Spectre v2: using BPIALL workaround
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (2664.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 26, 2022 02:31PM |
Registered: 7 months ago Posts: 142 |
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered PF_NETLINK/PF_ROUTE protocol family DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' cpuidle: using governor ladder mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling cryptd: max_cpu_qlen set to 1000 raid6: neonx8 gen() 592 MB/s raid6: neonx8 xor() 502 MB/s raid6: neonx4 gen() 1693 MB/s raid6: neonx4 xor() 1121 MB/s raid6: neonx2 gen() 2071 MB/s raid6: neonx2 xor() 1327 MB/s raid6: neonx1 gen() 1749 MB/s raid6: neonx1 xor() 1163 MB/s raid6: int32x8 gen() 244 MB/s raid6: int32x8 xor() 168 MB/s raid6: int32x4 gen() 280 MB/s raid6: int32x4 xor() 180 MB/s raid6: int32x2 gen() 448 MB/s raid6: int32x2 xor() 251 MB/s raid6: int32x1 gen() 512 MB/s raid6: int32x1 xor() 207 MB/s raid6: using algorithm neonx2 gen() 2071 MB/s raid6: .... xor() 1327 MB/s, rmw enabled raid6: using neon recovery algorithm SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered clocksource: Switched to clocksource arm_global_timer VFS: Disk quotas dquot_6.6.0 VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) FS-Cache: Loaded CacheFiles: Loaded NET: Registered PF_INET protocol family IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) TCP: Hash tables configured (established 8192 bind 8192) UDP hash table entries: 512 (order: 2, 16384 bytes, linear) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Trying to unpack rootfs image as initramfs... Initialise system trusted keyrings workingset: timestamp_bits=14 max_order=18 bucket_order=4 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). FS-Cache: Netfs 'cifs' registered for caching Key type cifs.idmap registered ksmbd: The ksmbd server is experimental, use at your own risk. ntfs3: Max link count 4000 ntfs3: Read-only LZX/Xpress compression included Freeing initrd memory: 1588K xor: measuring software checksum speed arm4regs : 2172 MB/sec 8regs : 1637 MB/sec 32regs : 1733 MB/sec neon : 1598 MB/sec xor: using function: arm4regs (2172 MB/sec) async_tx: api initialized (async) Key type asymmetric registered Asymmetric key parser 'x509' registered bounce: pool size: 64 pages Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler kyber registered armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled printk: console [ttyS0] disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 12500000) is a 16550A printk: console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, base_baud = 12500000) is a 16550A brd: module loaded loop: module loaded ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi host0: ahci-mvebu scsi host1: ahci-mvebu ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 52 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 52 hwmon hwmon0: temp1_input not attached to any thermal zone mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled mvneta f1034000.ethernet eth0: Using hardware mac address 00:50:43:36:98:34 usbcore: registered new interface driver lan78xx ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 48, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 5.15.79 ehci_hcd usb usb1: SerialNumber: f1058000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver ohci-platform: OHCI generic platform driver uhci_hcd: USB Universal Host Controller Interface driver xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000 xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 5.15.79 xhci-hcd usb usb2: SerialNumber: f10f0000.usb3 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 5.15.79 xhci-hcd usb usb3: SerialNumber: f10f0000.usb3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000 xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 5.15.79 xhci-hcd usb usb4: SerialNumber: f10f8000.usb3 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 ata1: SATA link down (SStatus 0 SControl 300) usb usb5: Product: xHCI Host Controller ata2: SATA link down (SStatus 0 SControl 300) usb usb5: Manufacturer: Linux 5.15.79 xhci-hcd usb usb5: SerialNumber: f10f8000.usb3 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected fotg210_hcd: FOTG210 Host Controller (EHCI) Driver Warning! fotg210_hcd should always be loaded before uhci_hcd and ohci_hcd, not after SPI driver max3421-hcd has no spi_device_id for maxim,max3421 usbcore: registered new interface driver usb-storage i2c_dev: i2c /dev entries driver mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs marvell-cesa f1090000.crypto: CESA device successfully registered hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered PF_INET6 protocol family Segment Routing with IPv6 In-situ OAM (IOAM) with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered PF_PACKET protocol family Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates input: gpio-keys as /devices/platform/gpio-keys/input/input0 Freeing unused kernel image (initmem) memory: 1024K Run /init as init process ### Press any key to stop and run shell... (2)usb 4-1: new high-speed USB device number 2 using xhci-hcd usb 4-1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 1.00 usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 4-1: Product: DataTraveler 2.0 usb 4-1: Manufacturer: Kingston usb 4-1: SerialNumber: 00241D8CE480FE10B97245FE usb-storage 4-1:1.0: USB Mass Storage device detected scsi host2: usb-storage 4-1:1.0 scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 4 sd 2:0:0:0: [sda] 15131636 512-byte logical blocks: (7.75 GB/7.21 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 2:0:0:0: [sda] Attached SCSI removable disk EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem EXT4-fs (sda2): INFO: recovery required on readonly filesystem EXT4-fs (sda2): write access will be enabled during recovery EXT4-fs (sda2): recovery complete EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. /init: line 79: can't create /sys/class/leds/system-blue/trigger: nonexistent directory /init: line 80: can't create /sys/class/leds/system-green/trigger: nonexistent directory /init: line 81: can't create /sys/class/leds/system-red/trigger: nonexistent directory ip: command line is not complete, try "help" INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. findfs: unable to resolve 'LABEL=rootfs' Files under mount point '/run' will be hidden. ... (warning). Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...done. Setting hostname to 'debian'...done. Activating swap:. EXT4-fs (sda2): re-mounted. Opts: (null). Quota mode: none. Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda2 e2fsck 1.46.2 (28-Feb-2021) rootfs: clean, 22098/470496 files, 246061/1878398 blocks . EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... random: dd: uninitialized urandom read (32 bytes read) Initializing random number generator...done. Starting Setting kernel variables: sysctl. mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL) mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:36:98:34 Sending on LPF/eth0/00:50:43:36:98:34 Sending on Socket/fallback DHCPREQUEST for 192.168.0.18 on eth0 to 255.255.255.255 port 67 mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST for 192.168.0.18 on eth0 to 255.255.255.255 port 67 DHCPNAK from 192.168.1.254 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPOFFER of 192.168.1.108 from 192.168.1.254 DHCPREQUEST for 192.168.1.108 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.108 from 192.168.1.254 bound to 192.168.1.108 -- renewal in 34475 seconds. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Not starting NFS kernel daemon: no exports. ... (warning). Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1829 (syslogd) . Starting periodic command scheduler: cron. random: dbus-daemon: uninitialized urandom read (12 bytes read) random: dbus-daemon: uninitialized urandom read (12 bytes read) Starting NTP server: ntpd. Starting system message bus: dbus. random: avahi-daemon: uninitialized urandom read (4 bytes read) Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. random: crng init done random: 1 urandom warning(s) missed due to ratelimiting Starting OpenBSD Secure Shell server: sshd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1859 (klogd) . Running local boot scripts (/etc/rc.local) Configuration file wrong or corrupted <13>Dec 31 16:00:31 root[1943]: Cannot read u-boot env ethaddr . Debian GNU/Linux 11 debian ttyS0 debian login:
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 26, 2022 03:46PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js,
Congrats!
Now try tftp the umage from kernel 6.0.7-mvebu-tld-1
and boot the same way.
-bodhi
===========================
Forum Wiki
bodhi's corner
Congrats!
Now try tftp the umage from kernel 6.0.7-mvebu-tld-1
Quote
https://forum.doozan.com/read.php?2,32146
Updated 09 Nov 2022:
Kernel 6.0.7-mvebu-tld-1 package has been uploaded.
and boot the same way.
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 27, 2022 12:21PM |
Registered: 7 months ago Posts: 142 |
With K6, can't detect or mount sda2
Perhaps because I was not using the K6 uRamdisk??
Edited 1 time(s). Last edit at 11/27/2022 12:23PM by i5Js.
Marvell>> setenv fdt_skip_update yes
Marvell>> setenv bootargs console=ttyS0,115200 root=/dev/sda2
Marvell>> setenv initrd_high 0xffffffff
Marvell>> setenv ipaddr 192.168.1.110; setenv serverip 192.168.1.23; tftp 0xa00000 uimagek6; tftp 0x1200000 uramdisk
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'uimagek6'.
Load address: 0xa00000
Loading: T T T T #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################
156.3 KiB/s
done
Bytes transferred = 5241862 (4ffc06 hex)
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'uramdisk'.
Load address: 0x1200000
Loading: #################################################################
##############################################
252 KiB/s
done
Bytes transferred = 1622632 (18c268 hex)
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... Device NOT ready
Request Sense returned 02 3A 00
1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> bootm 0xa00000 0x1200000
## Booting image at 00a00000 ...
## Booting kernel from Legacy Image at 00a00000 ...
Image Name: Linux-6.0.7-mvebu-tld-1
Created: 2022-11-27 18:04:37 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5241798 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01200000 ...
Image Name: Custom initramfs
Created: 2021-07-28 7:11:31 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1622568 Bytes = 1.5 MiB
Load Address: 00e00000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.0.7-mvebu-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 SMP PREEMPT Tue Nov 8 16:49:35 2
[ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Ex2 Ultra
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] percpu: Embedded 17 pages/cpu s38996 r8192 d22444 u69632
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda2
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1018376K/1048576K available (10240K kernel code, 1513K rwdata, 3472K rodata, 1024K init, 470K bss, 30200K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval)
[ 0.000001][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.000014][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
[ 0.000034][ T0] Switching to timer-based delay loop, resolution 1ns
[ 0.000260][ T0] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000267][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.001051][ T0] Console: colour dummy device 80x30
[ 0.001080][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000)
[ 0.001091][ T0] pid_max: default: 32768 minimum: 301
[ 0.001304][ T0] LSM: Security Framework initializing
[ 0.001453][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.001464][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.002128][ T0] CPU: Testing write buffer coherency: ok
[ 0.002152][ T0] CPU0: Spectre v2: using BPIALL workaround
[ 0.002367][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.003078][ T1] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.003085][ T1] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.003176][ T1] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.003266][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.003373][ T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.003489][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.003627][ T1] rcu: Hierarchical SRCU implementation.
[ 0.003632][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.004309][ T1] smp: Bringing up secondary CPUs ...
[ 0.004829][ T1] Booting CPU 1
[ 0.004997][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.005008][ T0] CPU1: Spectre v2: using BPIALL workaround
[ 0.005098][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.005105][ T1] SMP: Total of 2 processors activated (2664.00 BogoMIPS).
[ 0.005112][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.005568][ T1] devtmpfs: initialized
[ 0.008819][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.009073][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.009099][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.009197][ T1] prandom: seed boundary self test passed
[ 0.010849][ T1] prandom: 100 self tests passed
[ 0.010855][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.011776][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.012449][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.013118][ T1] audit: initializing netlink subsys (disabled)
[ 0.013302][ T24] audit: type=2000 audit(0.010:1): state=initialized audit_enabled=0 res=1
[ 0.013650][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.013859][ T1] cpuidle: using governor ladder
[ 0.013881][ T1] cpuidle: using governor menu
[ 0.013964][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.013971][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.014122][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.014130][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.200236][ T1] raid6: int32x8 gen() 244 MB/s
[ 0.370144][ T1] raid6: int32x4 gen() 263 MB/s
[ 0.540115][ T1] raid6: int32x2 gen() 459 MB/s
[ 0.710122][ T1] raid6: int32x1 gen() 532 MB/s
[ 0.710127][ T1] raid6: using algorithm int32x1 gen() 532 MB/s
[ 0.880136][ T1] raid6: .... xor() 205 MB/s, rmw enabled
[ 0.880141][ T1] raid6: using intx1 recovery algorithm
[ 0.880860][ T1] SCSI subsystem initialized
[ 0.881219][ T1] usbcore: registered new interface driver usbfs
[ 0.881252][ T1] usbcore: registered new interface driver hub
[ 0.881279][ T1] usbcore: registered new device driver usb
[ 0.881512][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 0.881517][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.881530][ T1] PTP clock support registered
[ 0.882494][ T1] vgaarb: loaded
[ 0.882851][ T1] clocksource: Switched to clocksource arm_global_timer
[ 0.883314][ T1] VFS: Disk quotas dquot_6.6.0
[ 0.883389][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.889794][ T1] NET: Registered PF_INET protocol family
[ 0.889955][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.891536][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.891620][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.891642][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.891710][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.891787][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.891969][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.892030][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.892057][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.892230][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.892811][ T1] RPC: Registered named UNIX socket transport module.
[ 0.892819][ T1] RPC: Registered udp transport module.
[ 0.892823][ T1] RPC: Registered tcp transport module.
[ 0.892826][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.892833][ T1] PCI: CLS 0 bytes, default 64
[ 0.892947][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.893194][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 0.903173][ T10] Trying to unpack rootfs image as initramfs...
[ 0.903192][ T10] Initramfs unpacking failed: invalid magic at start of compressed archive
[ 0.905611][ T10] Freeing initrd memory: 1588K
[ 0.929875][ T1] Initialise system trusted keyrings
[ 0.929943][ T1] Key type blacklist registered
[ 0.930276][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 0.930387][ T1] zbud: loaded
[ 0.931752][ T1] NFS: Registering the id_resolver key type
[ 0.931782][ T1] Key type id_resolver registered
[ 0.931786][ T1] Key type id_legacy registered
[ 0.931822][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.931832][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.987089][ T1] xor: measuring software checksum speed
[ 0.991624][ T1] arm4regs : 2172 MB/sec
[ 0.997531][ T1] 8regs : 1669 MB/sec
[ 1.003219][ T1] 32regs : 1733 MB/sec
[ 1.003223][ T1] xor: using function: arm4regs (2172 MB/sec)
[ 1.003232][ T1] async_tx: api initialized (async)
[ 1.003239][ T1] Key type asymmetric registered
[ 1.003243][ T1] Asymmetric key parser 'x509' registered
[ 1.004027][ T1] alg: self-tests for CTR-KDF (hmac(sha256)) passed
[ 1.004203][ T1] bounce: pool size: 64 pages
[ 1.004348][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 1.004451][ T1] io scheduler bfq registered
[ 1.006993][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 1.008067][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present!
[ 1.008734][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present!
[ 1.009697][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 1.063497][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 1.065503][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 1.123572][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 1.192306][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.195615][ T1] printk: console [ttyS0] disabled
[ 1.216100][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 39, base_baud = 12500000) is a 16550A
[ 2.253570][ T1] printk: console [ttyS0] enabled
[ 2.279478][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 40, base_baud = 12500000) is a 16550A
[ 2.290474][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
[ 2.298951][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
[ 2.307264][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
[ 2.315951][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 2.325767][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 2.336396][ T1] scsi host0: ahci-mvebu
[ 2.340993][ T1] scsi host1: ahci-mvebu
[ 2.345332][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
[ 2.354019][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
[ 2.364288][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 2.371386][ T1] nand: Macronix MX30LF2G18AC
[ 2.375976][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.384586][ T1] Bad block table found at page 131008, version 0x01
[ 2.391468][ T1] Bad block table found at page 130944, version 0x01
[ 2.398214][ T1] nand_read_bbt: bad block at 0x000002020000
[ 2.404103][ T1] nand_read_bbt: bad block at 0x0000062e0000
[ 2.409976][ T1] nand_read_bbt: bad block at 0x00000bac0000
[ 2.415851][ T1] nand_read_bbt: bad block at 0x00000d300000
[ 2.421717][ T1] nand_read_bbt: bad block at 0x00000dc60000
[ 2.427721][ T1] 8 fixed-partitions partitions found on MTD device pxa3xx_nand-0
[ 2.435445][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0":
[ 2.441577][ T1] 0x000000000000-0x000000500000 : "U-Boot"
[ 2.448648][ T1] 0x000000500000-0x000000a00000 : "uImage"
[ 2.455614][ T1] 0x000000a00000-0x000000f00000 : "uRamdisk"
[ 2.462739][ T1] 0x000000f00000-0x00000c800000 : "image.cfs"
[ 2.470335][ T1] 0x00000c800000-0x00000d700000 : "rescue fw"
[ 2.477561][ T1] 0x00000d700000-0x00000eb00000 : "config"
[ 2.484611][ T1] 0x00000eb00000-0x00000f500000 : "reserve1"
[ 2.491703][ T1] 0x00000f500000-0x00000ff00000 : "reserve2"
[ 2.499870][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 2.508473][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 2.524233][ T1] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 2.532299][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 2.545883][ T1] mvneta f1034000.ethernet eth0: Using hardware mac address 00:50:43:36:98:34
[ 2.555311][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.562598][ T1] ehci-pci: EHCI PCI platform driver
[ 2.567902][ T1] ehci-orion: EHCI orion driver
[ 2.572893][ T1] orion-ehci f1058000.usb: EHCI Host Controller
[ 2.579041][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 2.587469][ T1] orion-ehci f1058000.usb: irq 44, io mem 0xf1058000
[ 2.622865][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 2.629708][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
[ 2.638754][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.646755][ T1] usb usb1: Product: EHCI Host Controller
[ 2.652375][ T1] usb usb1: Manufacturer: Linux 6.0.7-mvebu-tld-1 ehci_hcd
[ 2.659486][ T1] usb usb1: SerialNumber: f1058000.usb
[ 2.665499][ T1] hub 1-0:1.0: USB hub found
[ 2.670015][ T1] hub 1-0:1.0: 1 port detected
[ 2.676361][ T1] usbcore: registered new interface driver usblp
[ 2.682725][ T1] usbcore: registered new interface driver usb-storage
[ 2.689962][ T1] mousedev: PS/2 mouse device common for all mice
[ 2.696301][ T663] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.702470][ T668] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.704179][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 2.714941][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2022-11-27T18:19:07 UTC (1669573147)
[ 2.725322][ T1] i2c_dev: i2c /dev entries driver
[ 2.730592][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported
[ 2.739658][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported
[ 2.751726][ T1] orion_wdt: Initial timeout 171 sec
[ 2.757539][ T1] device-mapper: uevent: version 1.0.3
[ 2.763145][ T1] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[ 2.772622][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 2.779914][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 2.787275][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 2.794668][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 2.801495][ T1] device-mapper: raid: Loading target version 1.15.1
[ 2.810542][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 2.818897][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 2.825270][ T1] usbcore: registered new interface driver usbhid
[ 2.831579][ T1] usbhid: USB HID core driver
[ 2.836597][ T1] drop_monitor: Initializing network drop monitor service
[ 2.844040][ T1] NET: Registered PF_INET6 protocol family
[ 2.850780][ T1] Segment Routing with IPv6
[ 2.855192][ T1] RPL Segment Routing with IPv6
[ 2.859968][ T1] In-situ OAM (IOAM) with IPv6
[ 2.864781][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.872938][ T1] NET: Registered PF_PACKET protocol family
[ 2.878864][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 2.883834][ T1] Key type dns_resolver registered
[ 2.888893][ T1] ThumbEE CPU extension supported.
[ 2.893906][ T1] Registering SWP/SWPB emulation handler
[ 2.899931][ T1] registered taskstats version 1
[ 2.904784][ T1] Loading compiled-in X.509 certificates
[ 2.910821][ T1] zswap: loaded using pool lzo/zbud
[ 2.916349][ T1] Key type ._fscrypt registered
[ 2.921087][ T1] Key type .fscrypt registered
[ 2.925751][ T1] Key type fscrypt-provisioning registered
[ 2.933052][ T1] Key type big_key registered
[ 2.938495][ T1] Key type encrypted registered
[ 2.950059][ T42] usb_phy_generic usb3_0_phy: dummy supplies not allowed for exclusive requests
[ 2.959258][ T42] usb_phy_generic usb3_1_phy: dummy supplies not allowed for exclusive requests
[ 2.968527][ T42] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 2.974668][ T42] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 2.983014][ T42] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 2.993046][ T42] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000
[ 2.999681][ T42] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 3.005746][ T42] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 3.014006][ T42] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 3.021226][ T42] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
[ 3.030257][ T42] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.038253][ T42] usb usb2: Product: xHCI Host Controller
[ 3.043870][ T42] usb usb2: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd
[ 3.050960][ T42] usb usb2: SerialNumber: f10f0000.usb3
[ 3.056835][ T42] hub 2-0:1.0: USB hub found
[ 3.061334][ T42] hub 2-0:1.0: 1 port detected
[ 3.066331][ T42] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.075280][ T42] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
[ 3.084307][ T42] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.092271][ T42] usb usb3: Product: xHCI Host Controller
[ 3.098078][ T42] usb usb3: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd
[ 3.105187][ T42] usb usb3: SerialNumber: f10f0000.usb3
[ 3.110998][ T42] hub 3-0:1.0: USB hub found
[ 3.115507][ T42] hub 3-0:1.0: 1 port detected
[ 3.120707][ T42] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 3.126875][ T42] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 3.135205][ T42] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 3.145238][ T42] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000
[ 3.151855][ T42] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 3.157995][ T42] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 3.166268][ T42] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 3.173478][ T42] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
[ 3.182492][ T42] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.190538][ T42] usb usb4: Product: xHCI Host Controller
[ 3.196160][ T42] usb usb4: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd
[ 3.203257][ T42] usb usb4: SerialNumber: f10f8000.usb3
[ 3.209115][ T42] hub 4-0:1.0: USB hub found
[ 3.213702][ T42] hub 4-0:1.0: 1 port detected
[ 3.218672][ T42] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.227691][ T42] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
[ 3.236720][ T42] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.244920][ T42] usb usb5: Product: xHCI Host Controller
[ 3.250527][ T42] usb usb5: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd
[ 3.257653][ T42] usb usb5: SerialNumber: f10f8000.usb3
[ 3.263511][ T42] hub 5-0:1.0: USB hub found
[ 3.268007][ T42] hub 5-0:1.0: 1 port detected
[ 3.273674][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 3.282264][ T1] md: Waiting for all devices to be available before autodetect
[ 3.289829][ T1] md: If you don't use raid, use raid=noautodetect
[ 3.296254][ T1] md: Autodetecting RAID arrays.
[ 3.301074][ T1] md: autorun ...
[ 3.304630][ T1] md: ... autorun DONE.
[ 3.309051][ T1] /dev/root: Can't open blockdev
[ 3.313904][ T1] VFS: Cannot open root device "sda2" or unknown-block(0,0): error -6
[ 3.321955][ T1] Please append a correct "root=" boot option; here are the available partitions:
[ 3.331061][ T1] 1f00 5120 mtdblock0
[ 3.331067][ T1] (driver?)
[ 3.339049][ T1] 1f01 5120 mtdblock1
[ 3.339054][ T1] (driver?)
[ 3.347034][ T1] 1f02 5120 mtdblock2
[ 3.347038][ T1] (driver?)
[ 3.355026][ T1] 1f03 189440 mtdblock3
[ 3.355031][ T1] (driver?)
[ 3.363012][ T1] 1f04 15360 mtdblock4
[ 3.363018][ T1] (driver?)
[ 3.370990][ T1] 1f05 20480 mtdblock5
[ 3.370995][ T1] (driver?)
[ 3.378978][ T1] 1f06 10240 mtdblock6
[ 3.378983][ T1] (driver?)
[ 3.386962][ T1] 1f07 10240 mtdblock7
[ 3.386966][ T1] (driver?)
[ 3.394943][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 3.403953][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.0.7-mvebu-tld-1 #1.0
[ 3.411742][ T1] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 3.418395][ T1] unwind_backtrace from show_stack+0x10/0x14
[ 3.424365][ T1] show_stack from dump_stack_lvl+0x40/0x4c
[ 3.430152][ T1] dump_stack_lvl from panic+0x104/0x328
[ 3.435677][ T1] panic from mount_block_root+0x150/0x1d8
[ 3.441377][ T1] mount_block_root from prepare_namespace+0x144/0x180
[ 3.448123][ T1] prepare_namespace from kernel_init_freeable+0x210/0x274
[ 3.455217][ T1] kernel_init_freeable from kernel_init+0x14/0x130
[ 3.461702][ T1] kernel_init from ret_from_fork+0x14/0x2c
[ 3.467486][ T1] Exception stack(0xf0831fb0 to 0xf0831ff8)
[ 3.473266][ T1] 1fa0: 00000000 00000000 00000000 00000000
[ 3.482189][ T1] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.491112][ T1] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 3.498463][ C1] CPU1: stopping
[ 3.501889][ C1] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.0.7-mvebu-tld-1 #1.0
[ 3.509678][ C1] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 3.516330][ C1] unwind_backtrace from show_stack+0x10/0x14
[ 3.522293][ C1] show_stack from dump_stack_lvl+0x40/0x4c
[ 3.528077][ C1] dump_stack_lvl from do_handle_IPI+0x208/0x2c0
[ 3.534296][ C1] do_handle_IPI from ipi_handler+0x14/0x20
[ 3.540078][ C1] ipi_handler from handle_percpu_devid_irq+0x58/0xfc
[ 3.546734][ C1] handle_percpu_devid_irq from handle_irq_desc+0x1c/0x2c
[ 3.553742][ C1] handle_irq_desc from gic_handle_irq+0x60/0x70
[ 3.559966][ C1] gic_handle_irq from generic_handle_arch_irq+0x28/0x3c
[ 3.566885][ C1] generic_handle_arch_irq from call_with_stack+0x18/0x20
[ 3.573894][ C1] call_with_stack from __irq_svc+0x98/0xc8
[ 3.579676][ C1] Exception stack(0xf0871f50 to 0xf0871f98)
[ 3.585456][ C1] 1f40: 00000001 00000000 00001101 c011d800
[ 3.594380][ C1] 1f60: 00000000 00000000 00000001 c0f65be8 c18db480 c100a070 00000000 00000000
[ 3.603301][ C1] 1f80: c1003d40 f0871fa0 c010c900 c010c8f0 60000113 ffffffff
[ 3.610651][ C1] __irq_svc from arch_cpu_idle+0x1c/0x38
[ 3.616259][ C1] arch_cpu_idle from default_idle_call+0x30/0x50
[ 3.622566][ C1] default_idle_call from do_idle+0x108/0x280
[ 3.628527][ C1] do_idle from cpu_startup_entry+0x18/0x1c
[ 3.634311][ C1] cpu_startup_entry from secondary_start_kernel+0x104/0x124
[ 3.641579][ C1] secondary_start_kernel from 0x101ec0
[ 3.647018][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
Perhaps because I was not using the K6 uRamdisk??
Edited 1 time(s). Last edit at 11/27/2022 12:23PM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 27, 2022 03:54PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js ,
> Perhaps because I was not using the K6 uRamdisk??
Perhaps! try kernel 6.0.7 initramfs (you are booting a much newer Debian rootfs on USB than that ramdisk).
-bodhi
===========================
Forum Wiki
bodhi's corner
> Perhaps because I was not using the K6 uRamdisk??
Perhaps! try kernel 6.0.7 initramfs (you are booting a much newer Debian rootfs on USB than that ramdisk).
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 28, 2022 08:19AM |
Registered: 7 months ago Posts: 142 |
Ok, I will update the uRamdisk.
I have also compiled a new Kernel 6 and uRamdisk, but I don't understand what means the lines after "Starting kernel..." but it stops there:
Now I will follow your steps to update the uRam and boot your K6
I have also compiled a new Kernel 6 and uRamdisk, but I don't understand what means the lines after "Starting kernel..." but it stops there:
Marvell>> setenv fdt_skip_update yes
Marvell>> setenv bootargs console=ttyS0,115200 root=/dev/sda2
Marvell>> setenv initrd_high 0xffffffff
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> setenv ipaddr 192.168.1.110; setenv serverip 192.168.1.23; tftp 0xa00000 uimage6; tftp 0x1200000 uramdisk
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'uimage6'.
Load address: 0xa00000
Loading: #################################################################
#################################################################
#################################################################
##############################
376 KiB/s
done
Bytes transferred = 3289507 (3231a3 hex)
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'uramdisk'.
Load address: 0x1200000
Loading: T #################################################################
##############################################
174.8 KiB/s
done
Bytes transferred = 1622632 (18c268 hex)
Marvell>> bootm 0xa00000 0x1200000
## Booting image at 00a00000 ...
## Booting kernel from Legacy Image at 00a00000 ...
Image Name: WDMC-Gen2
Created: 2022-11-28 13:25:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3289443 Bytes = 3.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01200000 ...
Image Name: Custom initramfs
Created: 2021-07-28 7:11:31 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1622568 Bytes = 1.5 MiB
Load Address: 00e00000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
DTB:0x003266D0 (0x00004A93)
C:0x000080E0-0x0032B1E0->0x00B71300-0x00E94400
DTB:0x00E8F8F0 (0x00004B10)
Uncompressing Linux... done, booting the kernel.
Now I will follow your steps to update the uRam and boot your K6
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 29, 2022 08:43AM |
Registered: 7 months ago Posts: 142 |
Hi,
I found why it was not working with the kernel 6, it was the kernel config. I have it up and running:
The sizes are perfect for the nand. @bodhi, any tip to flash it?
Then I should modify the envs to get the rootfs from the hard drive.
I found why it was not working with the kernel 6, it was the kernel config. I have it up and running:
root@wdmycloud:~# uname -a Linux wdmycloud 6.0.10+ #1 SMP Tue Nov 29 14:49:09 CET 2022 armv7l GNU/Linux
The sizes are perfect for the nand. @bodhi, any tip to flash it?
Then I should modify the envs to get the rootfs from the hard drive.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 29, 2022 02:40PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js,
> I found why it was not working with the kernel 6,
> it was the kernel config.
In what way?
> The sizes are perfect for the nand. @bodhi, any
> tip to flash it?
This is a NAS box, so you would want to update your kernel often. I always try to discourage people from storing kernel files in NAND. You dont really gain much using this approach.
The exception is when you want to run the rootfs from RAID array.
-bodhi
===========================
Forum Wiki
bodhi's corner
> I found why it was not working with the kernel 6,
> it was the kernel config.
In what way?
> The sizes are perfect for the nand. @bodhi, any
> tip to flash it?
This is a NAS box, so you would want to update your kernel often. I always try to discourage people from storing kernel files in NAND. You dont really gain much using this approach.
The exception is when you want to run the rootfs from RAID array.
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 29, 2022 03:54PM |
Registered: 7 months ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 29, 2022 03:56PM |
Registered: 7 months ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 30, 2022 02:25PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js,
Let recap where you are, and why you have to boot a certain way (tftp, USB, SATA,...) and which kernel. And post serial boot log, too.
-bodhi
===========================
Forum Wiki
bodhi's corner
Let recap where you are, and why you have to boot a certain way (tftp, USB, SATA,...) and which kernel. And post serial boot log, too.
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 30, 2022 03:21PM |
Registered: 7 months ago Posts: 142 |
Hi,
Many thanks.
The idea is get a kernel an uImage thin enough to fit into a nand. As I said, my idea is not to test a lot, just to have a box with latest OMV. I have followed this repository to compile my own kernel, using the dts for ex2 ultra I found here: https://github.com/Heisath/wdmc2-kernel
The first issue I have had is I am unable to boot from USB. I don’t know why, but it is what it is. Then you suggested to boot from tftp and worked flawless. The boot log is in my post: https://forum.doozan.com/read.php?2,67249,133455#msg-133455
Checking it, I have found that the mtd partitions are not detected, perhaps I missed something in the Linux.conf from that repository.
With your rootfs, kernel and uImage, the mtd partitions are there, but I don’t know why the sda is not mounted to continue booting: https://forum.doozan.com/read.php?2,67249,133463#msg-133463 in addition they are to big to flash into the nand, but ok, I could use the usb instead the nand.
And that is all,
Let me know if you need anything else.
And really appreciate your support with this forum.
Many thanks.
The idea is get a kernel an uImage thin enough to fit into a nand. As I said, my idea is not to test a lot, just to have a box with latest OMV. I have followed this repository to compile my own kernel, using the dts for ex2 ultra I found here: https://github.com/Heisath/wdmc2-kernel
The first issue I have had is I am unable to boot from USB. I don’t know why, but it is what it is. Then you suggested to boot from tftp and worked flawless. The boot log is in my post: https://forum.doozan.com/read.php?2,67249,133455#msg-133455
Checking it, I have found that the mtd partitions are not detected, perhaps I missed something in the Linux.conf from that repository.
With your rootfs, kernel and uImage, the mtd partitions are there, but I don’t know why the sda is not mounted to continue booting: https://forum.doozan.com/read.php?2,67249,133463#msg-133463 in addition they are to big to flash into the nand, but ok, I could use the usb instead the nand.
And that is all,
Let me know if you need anything else.
And really appreciate your support with this forum.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra November 30, 2022 07:57PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js,
OK. tftp is just a temporary mode of booting. And you have problem with this u-boot regarding USB Ext2 driver. So the next logical thing to do is to boot from NAND.
But before I help you with that, I think we need to try a bit more to see if we can get it to boot entirely from USB. And get some info along the way to see where things are on this box.
In reference to the successful tftp boot:
https://forum.doozan.com/read.php?2,67249,133459#msg-133459
This time, try:
Recreate the USB rootfs with 2 partitions, the first partition is type Ext2, the second partition is type Ext3. On the 1st partition, put the kernel files on /boot
Attach the USB drive, power up, interrupt serial console. And,
Now, if the 1st ext2ls command is successful but not with the 2nd, then this u-boot driver does not understand Ext3 filesystem. If both are succesfful then we made some mistake in testing before. And you can load the kernel files from that Ext2 partition using ext2load and boot it the same way as tftp.
Please post the serial console log from the u-boot banner until the last output.
-bodhi
===========================
Forum Wiki
bodhi's corner
OK. tftp is just a temporary mode of booting. And you have problem with this u-boot regarding USB Ext2 driver. So the next logical thing to do is to boot from NAND.
But before I help you with that, I think we need to try a bit more to see if we can get it to boot entirely from USB. And get some info along the way to see where things are on this box.
In reference to the successful tftp boot:
https://forum.doozan.com/read.php?2,67249,133459#msg-133459
This time, try:
Recreate the USB rootfs with 2 partitions, the first partition is type Ext2, the second partition is type Ext3. On the 1st partition, put the kernel files on /boot
/boot/uImage /boot/uInitrdAnd extract the rootfs to the 2nd partition like you did.
Attach the USB drive, power up, interrupt serial console. And,
ver printenv usb start sleep 5 ext2ls usb 0:1 / ext2ls usb 0:2 /
Now, if the 1st ext2ls command is successful but not with the 2nd, then this u-boot driver does not understand Ext3 filesystem. If both are succesfful then we made some mistake in testing before. And you can load the kernel files from that Ext2 partition using ext2load and boot it the same way as tftp.
Please post the serial console log from the u-boot banner until the last output.
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 01, 2022 03:34AM |
Registered: 7 months ago Posts: 142 |
Hi bodhi, below the logs requested:
And silence. I can't type or do anything. Your are right, something is wrong because I can't see any ext2 or ext3 partitions here.
I have tested with another usb key, using gpt instead mbr, and it can't detect it (as expected per https://forum.doozan.com/read.php?2,132015,132472#msg-132472)
Edited 3 time(s). Last edit at 12/01/2022 07:41AM by i5Js.
Press CTRL-A Z for help on special keys
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Load WD GrandTeton Serdes Config:
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | USB3 HOST0 |
| 5 | 00 | SGMII2 |
--------------------------------
PCIe, Idx 0: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
Creating 1 MTD partitions on "nand0":
0x00000f500000-0x00000ff00000 : "mtd=7"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=7"
UBI: MTD device size: 10 MiB
UBI: number of good PEBs: 80
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 48
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 9/4
UBIFS: mounted UBI device 0, volume 0, name "reserve2"
UBIFS: mounted read-only
UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 200807 bytes (196 KiB)
Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)...
Done
Set lan 2 WakeOnLan ok
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>> ver
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
arm-marvell-linux-gnueabi-gcc (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-4
GNU ld (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPA1
Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
autoload=no
baudrate=115200
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
bootargs=root=/dev/ram console=ttyS0,115200
bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rool
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=nand read.e 0x02000020 0x0500000 0x0500000; nand read.e 0x2900000 0x0a00
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bo;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nand;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd t
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bo
bootdelay=1
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=00:50:43:36:2c:34
eth1mtu=1500
eth2addr=00:50:43:36:98:34
eth2mtu=1500
eth3addr=00:50:43:2c:98:36
eth3mtu=1500
ethact=egiga2
ethaddr=00:50:43:98:2c:34
ethmtu=1500
ethprime=egiga2
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x-modular.dtb
filesize=12
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.11.110
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
loadaddr=0x02000000
loads_echo=0
mtddevname=u-boot
mtddevnum=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:34:98:36
nandEcc=nfcConfig=4bitecc
netbsd_en=no
netmask=255.255.255.0
netretry=no
partition=nand0,0
pcieTune=no
pexMode=RC
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
serverip=192.168.11.114
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdp;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usbActive=1
usbType=3
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3221/524284 bytes
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> sleep 5
Marvell>> ext2ls usb 0:1 /
And silence. I can't type or do anything. Your are right, something is wrong because I can't see any ext2 or ext3 partitions here.
I have tested with another usb key, using gpt instead mbr, and it can't detect it (as expected per https://forum.doozan.com/read.php?2,132015,132472#msg-132472)
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Edited 3 time(s). Last edit at 12/01/2022 07:41AM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 01, 2022 03:11PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js,
OK. So that proved the Ext2 driver is not working in this u-boot.
Your log was not good. It got cut off on the right side, especially the important part (printenv). Please post the printenv output again and make sure that it's legible on your browser.
-bodhi
===========================
Forum Wiki
bodhi's corner
OK. So that proved the Ext2 driver is not working in this u-boot.
Your log was not good. It got cut off on the right side, especially the important part (printenv). Please post the printenv output again and make sure that it's legible on your browser.
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 01, 2022 03:23PM |
Registered: 7 months ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 01, 2022 03:30PM |
Registered: 7 months ago Posts: 142 |
Let's see now.
Edited 1 time(s). Last edit at 12/01/2022 03:32PM by i5Js.
Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0x02000020 0x0500000 0x0500000; nand read.e 0x2900000 0x0a00000 0x0500000; bootm 0x02000020 0x2900000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=1 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:36:2c:34 eth1mtu=1500 eth2addr=00:50:43:36:98:34 eth2mtu=1500 eth3addr=00:50:43:2c:98:36 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:98:2c:34 ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:34:98:36 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=1 usbType=3 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3221/524284 bytes
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6 arm-marvell-linux-gnueabi-gcc (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) 4.6.4 GNU ld (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) 2.22.0.20120801
Edited 1 time(s). Last edit at 12/01/2022 03:32PM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 01, 2022 06:02PM |
Admin Registered: 12 years ago Posts: 17,721 |
i5Js,
We'll enable the mtd partitions in Linux so that they are accessible for flashing kernel files.
Again, in reference to the successful tftp boot:
https://forum.doozan.com/read.php?2,67249,133459#msg-133459
This time change the envs a bit:
And boot.
Log into Debian,
And then post the entire serial console log here.
-bodhi
===========================
Forum Wiki
bodhi's corner
We'll enable the mtd partitions in Linux so that they are accessible for flashing kernel files.
Again, in reference to the successful tftp boot:
https://forum.doozan.com/read.php?2,67249,133459#msg-133459
This time change the envs a bit:
setenv mtdparts 'mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2)'
setenv bootargs 'console=ttyS0,115200 root=/dev/sda2 ${mtdparts} earlyprintk=serial'
And boot.
Log into Debian,
cat /proc/mtd
And then post the entire serial console log here.
-bodhi
===========================
Forum Wiki
bodhi's corner
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 02, 2022 03:22AM |
Registered: 7 months ago Posts: 142 |
I have several logs here:
With your uImage:
It can detect the mtd partition, but it can not mount the sda2 USB partition to continue booting.
Edited 1 time(s). Last edit at 12/02/2022 03:23AM by i5Js.
With your uImage:
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Load WD GrandTeton Serdes Config:
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | USB3 HOST0 |
| 5 | 00 | SGMII2 |
--------------------------------
PCIe, Idx 0: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
l
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
Creating 1 MTD partitions on "nand0":
0x00000f500000-0x00000ff00000 : "mtd=7"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=7"
UBI: MTD device size: 10 MiB
UBI: number of good PEBs: 80
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 48
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 9/4
UBIFS: mounted UBI device 0, volume 0, name "reserve2"
UBIFS: mounted read-only
UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 200807 bytes (196 KiB)
Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)...
Done
Set lan 2 WakeOnLan ok
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>> setenv initrd_high 0xffffffff
Marvell>> setenv mtdparts 'mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2)'
Marvell>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda2 ${mtdparts} earlyprintk=serial'
Marvell>> setenv ipaddr 192.168.1.110; setenv serverip 192.168.1.23; tftp 0xa00000 boot.b/uImage; tftp 0x1200000 boot.b/uramdisk
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'boot.b/uImage'.
Load address: 0xa00000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################
168 KiB/s
done
Bytes transferred = 5241862 (4ffc06 hex)
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'boot.b/uramdisk'.
Load address: 0x1200000
Loading: #################################################################
##############################################
200.2 KiB/s
done
Bytes transferred = 1622632 (18c268 hex)
Marvell>> bootm 0xa00000 0x1200000
## Booting image at 00a00000 ...
## Booting kernel from Legacy Image at 00a00000 ...
Image Name: Linux-6.0.7-mvebu-tld-1
Created: 2022-11-27 18:04:37 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5241798 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01200000 ...
Image Name: Custom initramfs
Created: 2021-07-28 7:11:31 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1622568 Bytes = 1.5 MiB
Load Address: 00e00000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.0.7-mvebu-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 SMP PREEMPT Tue Nov 8 16:49:35 PST 2022
[ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Ex2 Ultra
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] percpu: Embedded 17 pages/cpu s38996 r8192 d22444 u69632
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda2 ${mtdparts} earlyprintk=serial
[ 0.000000][ T0] Unknown kernel command line parameters "${mtdparts}", will be passed to user space.
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1018376K/1048576K available (10240K kernel code, 1513K rwdata, 3472K rodata, 1024K init, 470K bss, 30200K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval)
[ 0.000000][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.008677][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
[ 0.020384][ T0] Switching to timer-based delay loop, resolution 1ns
[ 0.027197][ T0] Ignoring duplicate/late registration of read_current_timer delay
[ 0.034914][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.047246][ T0] Console: colour dummy device 80x30
[ 0.052392][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000)
[ 0.063665][ T0] pid_max: default: 32768 minimum: 301
[ 0.069171][ T0] LSM: Security Framework initializing
[ 0.074612][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.082599][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.091675][ T0] CPU: Testing write buffer coherency: ok
[ 0.097261][ T0] CPU0: Spectre v2: using BPIALL workaround
[ 0.103194][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.110256][ T1] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.118169][ T1] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.125016][ T1] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.131882][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.138854][ T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.144779][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.151775][ T1] rcu: Hierarchical SRCU implementation.
[ 0.157258][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.163847][ T1] smp: Bringing up secondary CPUs ...
[ 0.169611][ T1] Booting CPU 1
[ 0.173079][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.173090][ T0] CPU1: Spectre v2: using BPIALL workaround
[ 0.185233][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.190035][ T1] SMP: Total of 2 processors activated (2664.00 BogoMIPS).
[ 0.197068][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.202811][ T1] devtmpfs: initialized
[ 0.210153][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.218805][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.229328][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.236880][ T1] prandom: seed boundary self test passed
[ 0.244035][ T1] prandom: 100 self tests passed
[ 0.248815][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.255625][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.262956][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.271179][ T1] audit: initializing netlink subsys (disabled)
[ 0.277438][ T24] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1
[ 0.277786][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.286049][ T1] cpuidle: using governor ladder
[ 0.297537][ T1] cpuidle: using governor menu
[ 0.302258][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.310939][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.317594][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.326350][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.537222][ T1] raid6: int32x8 gen() 244 MB/s
[ 0.707128][ T1] raid6: int32x4 gen() 263 MB/s
[ 0.877094][ T1] raid6: int32x2 gen() 459 MB/s
[ 1.047045][ T1] raid6: int32x1 gen() 532 MB/s
[ 1.051993][ T1] raid6: using algorithm int32x1 gen() 532 MB/s
[ 1.227085][ T1] raid6: .... xor() 205 MB/s, rmw enabled
[ 1.232644][ T1] raid6: using intx1 recovery algorithm
[ 1.238717][ T1] SCSI subsystem initialized
[ 1.243482][ T1] usbcore: registered new interface driver usbfs
[ 1.249706][ T1] usbcore: registered new interface driver hub
[ 1.255716][ T1] usbcore: registered new device driver usb
[ 1.261727][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.267377][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.277186][ T1] PTP clock support registered
[ 1.282736][ T1] vgaarb: loaded
[ 1.286537][ T1] clocksource: Switched to clocksource arm_global_timer
[ 1.293832][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.298559][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.313444][ T1] NET: Registered PF_INET protocol family
[ 1.319226][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.328852][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 1.338041][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.346470][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.354997][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.362908][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.370126][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 1.378259][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.385564][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.393456][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.400327][ T1] RPC: Registered named UNIX socket transport module.
[ 1.406970][ T1] RPC: Registered udp transport module.
[ 1.412350][ T1] RPC: Registered tcp transport module.
[ 1.417736][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.424848][ T1] PCI: CLS 0 bytes, default 64
[ 1.429563][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.429632][ T10] Trying to unpack rootfs image as initramfs...
[ 1.442883][ T10] Initramfs unpacking failed: invalid magic at start of compressed archive
[ 1.442897][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 1.453671][ T10] Freeing initrd memory: 1588K
[ 1.461150][ T1] Initialise system trusted keyrings
[ 1.469935][ T1] Key type blacklist registered
[ 1.474757][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 1.481982][ T1] zbud: loaded
[ 1.486517][ T1] NFS: Registering the id_resolver key type
[ 1.492326][ T1] Key type id_resolver registered
[ 1.497201][ T1] Key type id_legacy registered
[ 1.501929][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.509316][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.571380][ T1] xor: measuring software checksum speed
[ 1.581391][ T1] arm4regs : 2172 MB/sec
[ 1.592321][ T1] 8regs : 1669 MB/sec
[ 1.603031][ T1] 32regs : 1733 MB/sec
[ 1.608072][ T1] xor: using function: arm4regs (2172 MB/sec)
[ 1.613976][ T1] async_tx: api initialized (async)
[ 1.619018][ T1] Key type asymmetric registered
[ 1.623791][ T1] Asymmetric key parser 'x509' registered
[ 1.630135][ T1] alg: self-tests for CTR-KDF (hmac(sha256)) passed
[ 1.636740][ T1] bounce: pool size: 64 pages
[ 1.641368][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 1.649569][ T1] io scheduler bfq registered
[ 1.656759][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 1.665374][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present!
[ 1.674495][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present!
[ 1.683906][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 1.757183][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 1.767261][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 1.827257][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 1.912682][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.922279][ T1] printk: console [ttyS0] disabled
[ 1.947745][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 39, base_baud = 12500000) is a 16550A
[ 1.957426][ T1] printk: console [ttyS0] enabled
[ 1.957426][ T1] printk: console [ttyS0] enabled
[ 1.967250][ T1] printk: bootconsole [earlycon0] disabled
[ 1.967250][ T1] printk: bootconsole [earlycon0] disabled
[ 1.999533][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 40, base_baud = 12500000) is a 16550A
[ 2.010470][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
[ 2.018929][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
[ 2.027228][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
[ 2.035852][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 2.045666][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 2.056320][ T1] scsi host0: ahci-mvebu
[ 2.060968][ T1] scsi host1: ahci-mvebu
[ 2.065278][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
[ 2.074048][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
[ 2.083786][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 2.090948][ T1] nand: Macronix MX30LF2G18AC
[ 2.095507][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.104104][ T1] Bad block table found at page 131008, version 0x01
[ 2.111026][ T1] Bad block table found at page 130944, version 0x01
[ 2.117767][ T1] nand_read_bbt: bad block at 0x000002020000
[ 2.123638][ T1] nand_read_bbt: bad block at 0x0000062e0000
[ 2.129518][ T1] nand_read_bbt: bad block at 0x00000bac0000
[ 2.135385][ T1] nand_read_bbt: bad block at 0x00000d300000
[ 2.141256][ T1] nand_read_bbt: bad block at 0x00000dc60000
[ 2.147247][ T1] 8 fixed-partitions partitions found on MTD device pxa3xx_nand-0
[ 2.154956][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0":
[ 2.161095][ T1] 0x000000000000-0x000000500000 : "U-Boot"
[ 2.167874][ T1] 0x000000500000-0x000000a00000 : "uImage"
[ 2.174520][ T1] 0x000000a00000-0x000000f00000 : "uRamdisk"
[ 2.181490][ T1] 0x000000f00000-0x00000c800000 : "image.cfs"
[ 2.188907][ T1] 0x00000c800000-0x00000d700000 : "rescue fw"
[ 2.195823][ T1] 0x00000d700000-0x00000eb00000 : "config"
[ 2.202549][ T1] 0x00000eb00000-0x00000f500000 : "reserve1"
[ 2.209398][ T1] 0x00000f500000-0x00000ff00000 : "reserve2"
[ 2.216929][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 2.225511][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 2.239365][ T1] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 2.247209][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 2.259435][ T1] mvneta f1034000.ethernet eth0: Using hardware mac address 00:50:43:36:98:34
[ 2.268584][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.275869][ T1] ehci-pci: EHCI PCI platform driver
[ 2.281095][ T1] ehci-orion: EHCI orion driver
[ 2.286046][ T1] orion-ehci f1058000.usb: EHCI Host Controller
[ 2.292204][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 2.300617][ T1] orion-ehci f1058000.usb: irq 44, io mem 0xf1058000
[ 2.346557][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 2.353477][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
[ 2.362524][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.370510][ T1] usb usb1: Product: EHCI Host Controller
[ 2.376129][ T1] usb usb1: Manufacturer: Linux 6.0.7-mvebu-tld-1 ehci_hcd
[ 2.383237][ T1] usb usb1: SerialNumber: f1058000.usb
[ 2.389067][ T1] hub 1-0:1.0: USB hub found
[ 2.393567][ T1] hub 1-0:1.0: 1 port detected
[ 2.399403][ T1] usbcore: registered new interface driver usblp
[ 2.405717][ T1] usbcore: registered new interface driver usb-storage
[ 2.408138][ T668] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.418721][ T663] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.424994][ T1] mousedev: PS/2 mouse device common for all mice
[ 2.432742][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 2.439073][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-02T09:20:20 UTC (1669972820)
[ 2.449280][ T1] i2c_dev: i2c /dev entries driver
[ 2.454462][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported
[ 2.463300][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported
[ 2.474487][ T1] orion_wdt: Initial timeout 171 sec
[ 2.480200][ T1] device-mapper: uevent: version 1.0.3
[ 2.485724][ T1] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[ 2.495171][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 2.502452][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 2.509810][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 2.517203][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 2.524030][ T1] device-mapper: raid: Loading target version 1.15.1
[ 2.532711][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 2.540833][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 2.547017][ T1] usbcore: registered new interface driver usbhid
[ 2.553324][ T1] usbhid: USB HID core driver
[ 2.558245][ T1] drop_monitor: Initializing network drop monitor service
[ 2.565642][ T1] NET: Registered PF_INET6 protocol family
[ 2.572351][ T1] Segment Routing with IPv6
[ 2.576765][ T1] RPL Segment Routing with IPv6
[ 2.581538][ T1] In-situ OAM (IOAM) with IPv6
[ 2.586252][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.593968][ T1] NET: Registered PF_PACKET protocol family
[ 2.599941][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 2.604890][ T1] Key type dns_resolver registered
[ 2.610012][ T1] ThumbEE CPU extension supported.
[ 2.615010][ T1] Registering SWP/SWPB emulation handler
[ 2.620980][ T1] registered taskstats version 1
[ 2.625811][ T1] Loading compiled-in X.509 certificates
[ 2.631872][ T1] zswap: loaded using pool lzo/zbud
[ 2.637378][ T1] Key type ._fscrypt registered
[ 2.642115][ T1] Key type .fscrypt registered
[ 2.646776][ T1] Key type fscrypt-provisioning registered
[ 2.654090][ T1] Key type big_key registered
[ 2.659538][ T1] Key type encrypted registered
[ 2.671148][ T10] usb_phy_generic usb3_0_phy: dummy supplies not allowed for exclusive requests
[ 2.680532][ T10] usb_phy_generic usb3_1_phy: dummy supplies not allowed for exclusive requests
[ 2.690071][ T10] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 2.696132][ T10] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 2.704635][ T10] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 2.714699][ T10] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000
[ 2.721331][ T10] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 2.727394][ T10] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 2.735636][ T10] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 2.742856][ T10] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
[ 2.751886][ T10] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.759870][ T10] usb usb2: Product: xHCI Host Controller
[ 2.765475][ T10] usb usb2: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd
[ 2.772572][ T10] usb usb2: SerialNumber: f10f0000.usb3
[ 2.778645][ T10] hub 2-0:1.0: USB hub found
[ 2.783147][ T10] hub 2-0:1.0: 1 port detected
[ 2.788301][ T10] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.797253][ T10] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
[ 2.806267][ T10] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.814245][ T10] usb usb3: Product: xHCI Host Controller
[ 2.819941][ T10] usb usb3: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd
[ 2.827044][ T10] usb usb3: SerialNumber: f10f0000.usb3
[ 2.833013][ T10] hub 3-0:1.0: USB hub found
[ 2.837524][ T10] hub 3-0:1.0: 1 port detected
[ 2.842750][ T10] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 2.848920][ T10] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 2.857245][ T10] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 2.867264][ T10] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000
[ 2.873883][ T10] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 2.880026][ T10] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 2.888412][ T10] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 2.895611][ T10] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
[ 2.904637][ T10] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.912674][ T10] usb usb4: Product: xHCI Host Controller
[ 2.918293][ T10] usb usb4: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd
[ 2.925382][ T10] usb usb4: SerialNumber: f10f8000.usb3
[ 2.931222][ T10] hub 4-0:1.0: USB hub found
[ 2.935720][ T10] hub 4-0:1.0: 1 port detected
[ 2.940783][ T10] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.949801][ T10] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
[ 2.958828][ T10] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.966946][ T10] usb usb5: Product: xHCI Host Controller
[ 2.972554][ T10] usb usb5: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd
[ 2.979669][ T10] usb usb5: SerialNumber: f10f8000.usb3
[ 2.985477][ T10] hub 5-0:1.0: USB hub found
[ 2.989988][ T10] hub 5-0:1.0: 1 port detected
[ 2.995589][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 3.004217][ T1] md: Waiting for all devices to be available before autodetect
[ 3.011770][ T1] md: If you don't use raid, use raid=noautodetect
[ 3.018199][ T1] md: Autodetecting RAID arrays.
[ 3.023018][ T1] md: autorun ...
[ 3.026526][ T1] md: ... autorun DONE.
[ 3.030935][ T1] /dev/root: Can't open blockdev
[ 3.035763][ T1] VFS: Cannot open root device "sda2" or unknown-block(0,0): error -6
[ 3.043849][ T1] Please append a correct "root=" boot option; here are the available partitions:
[ 3.052965][ T1] 1f00 5120 mtdblock0
[ 3.052972][ T1] (driver?)
[ 3.060977][ T1] 1f01 5120 mtdblock1
[ 3.060982][ T1] (driver?)
[ 3.068987][ T1] 1f02 5120 mtdblock2
[ 3.068992][ T1] (driver?)
[ 3.076977][ T1] 1f03 189440 mtdblock3
[ 3.076983][ T1] (driver?)
[ 3.084956][ T1] 1f04 15360 mtdblock4
[ 3.084960][ T1] (driver?)
[ 3.092956][ T1] 1f05 20480 mtdblock5
[ 3.092962][ T1] (driver?)
[ 3.100944][ T1] 1f06 10240 mtdblock6
[ 3.100949][ T1] (driver?)
[ 3.108933][ T1] 1f07 10240 mtdblock7
[ 3.108938][ T1] (driver?)
[ 3.116934][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 3.125944][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.0.7-mvebu-tld-1 #1.0
[ 3.133733][ T1] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 3.140385][ T1] unwind_backtrace from show_stack+0x10/0x14
[ 3.146355][ T1] show_stack from dump_stack_lvl+0x40/0x4c
[ 3.152142][ T1] dump_stack_lvl from panic+0x104/0x328
[ 3.157668][ T1] panic from mount_block_root+0x150/0x1d8
[ 3.163369][ T1] mount_block_root from prepare_namespace+0x144/0x180
[ 3.170114][ T1] prepare_namespace from kernel_init_freeable+0x210/0x274
[ 3.177209][ T1] kernel_init_freeable from kernel_init+0x14/0x130
[ 3.183695][ T1] kernel_init from ret_from_fork+0x14/0x2c
[ 3.189479][ T1] Exception stack(0xf0831fb0 to 0xf0831ff8)
[ 3.195259][ T1] 1fa0: 00000000 00000000 00000000 00000000
[ 3.204181][ T1] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.213102][ T1] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 3.220454][ C1] CPU1: stopping
[ 3.223880][ C1] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.0.7-mvebu-tld-1 #1.0
[ 3.231670][ C1] Hardware name: Marvell Armada 380/385 (Device Tree)
[ 3.238321][ C1] unwind_backtrace from show_stack+0x10/0x14
[ 3.244283][ C1] show_stack from dump_stack_lvl+0x40/0x4c
[ 3.250068][ C1] dump_stack_lvl from do_handle_IPI+0x208/0x2c0
[ 3.256287][ C1] do_handle_IPI from ipi_handler+0x14/0x20
[ 3.262068][ C1] ipi_handler from handle_percpu_devid_irq+0x58/0xfc
[ 3.268723][ C1] handle_percpu_devid_irq from handle_irq_desc+0x1c/0x2c
[ 3.275730][ C1] handle_irq_desc from gic_handle_irq+0x60/0x70
[ 3.281953][ C1] gic_handle_irq from generic_handle_arch_irq+0x28/0x3c
[ 3.288874][ C1] generic_handle_arch_irq from call_with_stack+0x18/0x20
[ 3.295883][ C1] call_with_stack from __irq_svc+0x98/0xc8
[ 3.301666][ C1] Exception stack(0xf0871f50 to 0xf0871f98)
[ 3.307445][ C1] 1f40: 00000001 00000000 000024a1 c011d800
[ 3.316368][ C1] 1f60: 00000000 00000000 00000001 c0f65be8 c18da180 c100a070 00000000 00000000
[ 3.325289][ C1] 1f80: c1003d40 f0871fa0 c010c900 c010c8f0 60000113 ffffffff
[ 3.332638][ C1] __irq_svc from arch_cpu_idle+0x1c/0x38
[ 3.338246][ C1] arch_cpu_idle from default_idle_call+0x30/0x50
[ 3.344553][ C1] default_idle_call from do_idle+0x108/0x280
[ 3.350513][ C1] do_idle from cpu_startup_entry+0x18/0x1c
[ 3.356297][ C1] cpu_startup_entry from secondary_start_kernel+0x104/0x124
[ 3.363565][ C1] secondary_start_kernel from 0x101ec0
[ 3.369004][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
It can detect the mtd partition, but it can not mount the sda2 USB partition to continue booting.
Edited 1 time(s). Last edit at 12/02/2022 03:23AM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 02, 2022 03:29AM |
Registered: 7 months ago Posts: 142 |
With my own kernel compiled:
It can boot to debian, but it can not detected the mtd partitions
Edited 1 time(s). Last edit at 12/02/2022 06:45AM by i5Js.
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Load WD GrandTeton Serdes Config:
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | USB3 HOST0 |
| 5 | 00 | SGMII2 |
--------------------------------
PCIe, Idx 0: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
Creating 1 MTD partitions on "nand0":
0x00000f500000-0x00000ff00000 : "mtd=7"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=7"
UBI: MTD device size: 10 MiB
UBI: number of good PEBs: 80
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 48
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 9/4
UBIFS: mounted UBI device 0, volume 0, name "reserve2"
UBIFS: mounted read-only
UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 200807 bytes (196 KiB)
Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)...
Done
Set lan 2 WakeOnLan ok
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv fdt_skip_update yes
Marvell>> setenv initrd_high 0xffffffff
Marvell>> setenv mtdparts 'mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2)'
Marvell>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda2 ${mtdparts} earlyprintk=serial'
Marvell>> setenv ipaddr 192.168.1.110; setenv serverip 192.168.1.23; tftp 0xa00000 boot/uImage-6.0.10; tftp 0x1200000 boot/uramdiskk6
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'boot/uImage-6.0.10'.
Load address: 0xa00000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
760.7 KiB/s
done
Bytes transferred = 3804547 (3a0d83 hex)
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'boot/uramdiskk6'.
Load address: 0x1200000
Loading: #################################################################
##############################################
606.4 KiB/s
done
Bytes transferred = 1622632 (18c268 hex)
Marvell>> bootm 0xa00000 0x1200000
## Booting image at 00a00000 ...
## Booting kernel from Legacy Image at 00a00000 ...
Image Name: WDMC-Gen2
Created: 2022-11-29 14:24:14 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3804483 Bytes = 3.6 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01200000 ...
Image Name: Custom initramfs
Created: 2021-07-28 7:11:31 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1622568 Bytes = 1.5 MiB
Load Address: 00e00000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
DTB:0x003A42B0 (0x00004A93)
C:0x000080E0-0x003A8DE0->0x00C7C500-0x0101D200
DTB:0x010186D0 (0x00004B30)
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 6.0.10+ (root@virtsrv) (arm-none-eabi-gcc (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027], GNU ld (2.35.2-2+14+b2) 2.35.2) #1 SMP Tue Nov 29 14:49:09 CET 2022
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: WD MyCloud Ex2 Ultra
Memory policy: Data cache writealloc
Zone ranges:
Normal [mem 0x0000000000000000-0x000000002fffffff]
HighMem [mem 0x0000000030000000-0x000000003fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000000000-0x000000003fffffff]
Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
percpu: Embedded 11 pages/cpu s14164 r8192 d22700 u45056
Built 1 zonelists, mobility grouping on. Total pages: 260416
Kernel command line: console=ttyS0,115200 root=/dev/sda2 ${mtdparts} earlyprintk=serial
Unknown kernel command line parameters "${mtdparts} earlyprintk=serial", will be passed to user space.
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 1024692K/1048576K available (7389K kernel code, 494K rwdata, 1928K rodata, 1024K init, 338K bss, 23884K reserved, 0K cma-reserved, 262144K highmem)
rcu: Hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 D prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
rcu: srcu_init: Setting srcu_struct sizes based on contention.
sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
Switching to timer-based delay loop, resolution 1ns
Ignoring duplicate/late registration of read_current_timer delay
clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
CPU: Testing write buffer coherency: ok
CPU0: Spectre v2: using BPIALL workaround
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100060
mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
mvebu-pmsu: Initializing Power Management Service Unit
rcu: Hierarchical SRCU implementation.
rcu: Max phase no-delay instances is 1000.
smp: Bringing up secondary CPUs ...
Booting CPU 1
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU1: Spectre v2: using BPIALL workaround
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (2664.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes, linear)
pinctrl core: initialized pinctrl subsystem
NET: Registered PF_NETLINK/PF_ROUTE protocol family
DMA: preallocated 256 KiB pool for atomic coherent allocations
thermal_sys: Registered thermal governor 'step_wise'
cpuidle: using governor ladder
mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
cryptd: max_cpu_qlen set to 1000
raid6: neonx8 gen() 592 MB/s
raid6: neonx4 gen() 1694 MB/s
raid6: neonx2 gen() 2070 MB/s
raid6: neonx1 gen() 1749 MB/s
raid6: int32x8 gen() 244 MB/s
raid6: int32x4 gen() 280 MB/s
raid6: int32x2 gen() 448 MB/s
raid6: int32x1 gen() 515 MB/s
raid6: using algorithm neonx2 gen() 2070 MB/s
raid6: .... xor() 1328 MB/s, rmw enabled
raid6: using neon recovery algorithm
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
clocksource: Switched to clocksource arm_global_timer
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
FS-Cache: Loaded
CacheFiles: Loaded
NET: Registered PF_INET protocol family
IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
TCP: Hash tables configured (established 8192 bind 8192)
UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
Initialise system trusted keyrings
workingset: timestamp_bits=14 max_order=18 bucket_order=4
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
Key type cifs.idmap registered
Freeing initrd memory: 1588K
xor: measuring software checksum speed
arm4regs : 2172 MB/sec
8regs : 1549 MB/sec
32regs : 1733 MB/sec
neon : 1634 MB/sec
xor: using function: arm4regs (2172 MB/sec)
async_tx: api initialized (async)
Key type asymmetric registered
Asymmetric key parser 'x509' registered
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
io scheduler kyber registered
armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
mv_xor f1060800.xor: Marvell shared XOR driver
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
printk: console [ttyS0] disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 38, base_baud = 12500000) is a 16550A
printk: console [ttyS0] enabled
f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 39, base_baud = 12500000) is a 16550A
brd: module loaded
loop: module loaded
ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi host0: ahci-mvebu
scsi host1: ahci-mvebu
ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 40
ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 40
hwmon hwmon0: temp1_input not attached to any thermal zone
mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
mvneta f1034000.ethernet eth0: Using hardware mac address 00:50:43:36:98:34
usbcore: registered new interface driver lan78xx
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-orion: EHCI orion driver
orion-ehci f1058000.usb: EHCI Host Controller
orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
orion-ehci f1058000.usb: irq 42, io mem 0xf1058000
orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 6.0.10+ ehci_hcd
usb usb1: SerialNumber: f1058000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-platform: OHCI generic platform driver
uhci_hcd: USB Universal Host Controller Interface driver
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
xhci-hcd f10f0000.usb3: irq 43, io mem 0xf10f0000
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 6.0.10+ xhci-hcd
usb usb2: SerialNumber: f10f0000.usb3
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 6.0.10+ xhci-hcd
usb usb3: SerialNumber: f10f0000.usb3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
xhci-hcd f10f8000.usb3: irq 44, io mem 0xf10f8000
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 6.0.10+ xhci-hcd
usb usb4: SerialNumber: f10f8000.usb3
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
ata2: SATA link down (SStatus 0 SControl 300)
usb usb5: Product: xHCI Host Controller
ata1: SATA link down (SStatus 0 SControl 300)
usb usb5: Manufacturer: Linux 6.0.10+ xhci-hcd
usb usb5: SerialNumber: f10f8000.usb3
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
fotg210_hcd: FOTG210 Host Controller (EHCI) Driver
Warning! fotg210_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
SPI driver max3421-hcd has no spi_device_id for maxim,max3421
usbcore: registered new interface driver usb-storage
i2c_dev: i2c /dev entries driver
mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported
mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported
device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
ledtrig-cpu: registered to indicate activity on CPUs
marvell-cesa f1090000.crypto: CESA device successfully registered
hid: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
NET: Registered PF_INET6 protocol family
Segment Routing with IPv6
In-situ OAM (IOAM) with IPv6
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
NET: Registered PF_PACKET protocol family
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
Registering SWP/SWPB emulation handler
Loading compiled-in X.509 certificates
input: gpio-keys as /devices/platform/gpio-keys/input/input0
Freeing unused kernel image (initmem) memory: 1024K
Run /init as init process
### Press any key to stop and run shell... (2)usb 4-1: new high-speed USB device number 2 using xhci-hcd
usb 4-1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 1.00
usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-1: Product: DataTraveler 2.0
usb 4-1: Manufacturer: Kingston
usb 4-1: SerialNumber: 00241D8CE480FE10B97245FE
usb-storage 4-1:1.0: USB Mass Storage device detected
scsi host2: usb-storage 4-1:1.0
scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 4
sd 2:0:0:0: [sda] 15131636 512-byte logical blocks: (7.75 GB/7.21 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI removable disk
EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem
EXT4-fs (sda2): mounted filesystem with ordered data mode. Quota mode: none.
/init: line 79: can't create /sys/class/leds/system-blue/trigger: nonexistent directory
/init: line 80: can't create /sys/class/leds/system-green/trigger: nonexistent directory
/init: line 81: can't create /sys/class/leds/system-red/trigger: nonexistent directory
ip: command line is not complete, try "help"
systemd[1]: System time before build time, advancing clock.
systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
It can boot to debian, but it can not detected the mtd partitions
root@wdmycloud:~# cat /proc/mtd dev: size erasesize name
Edited 1 time(s). Last edit at 12/02/2022 06:45AM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 02, 2022 03:29AM |
Registered: 7 months ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 02, 2022 06:30AM |
Registered: 7 months ago Posts: 142 |
I have compiled the kernel one more time, following this script (https://github.com/piotrekzurek/WDMC-Ex2-Ultra)
It has some improvements, and it seems he plays with the nand creating more partitions, I guess for stock kernel and Debian. Anyway, apart of that, this time, it boots successfully, and it detects the mtd partitions. Logs below:
It has some improvements, and it seems he plays with the nand creating more partitions, I guess for stock kernel and Debian. Anyway, apart of that, this time, it boots successfully, and it detects the mtd partitions. Logs below:
OPTIONS: I18n
Compiled on Aug 13 2017, 15:25:34.
Port /dev/ttyUSB0, 13:21:02
Press CTRL-A Z for help on special keys
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Load WD GrandTeton Serdes Config:
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | USB3 HOST0 |
| 5 | 00 | SGMII2 |
--------------------------------
PCIe, Idx 0: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01_v1.04 (Apr 19 2020 - 23:10:38) Marvell version: 2014_T3.0p6
mvBoardIdIndexGet(boardId) = 1
Board: GrandTeton DB6820
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 200 [MHz]
DDR @ 666 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fece000:0x3ff96000
BSS: 0x3ffef654
Stack: 0x3f9cdf20
Heap: 0x3f9ce000:0x3fece000
raise: Signal # 8 caught
raise: Signal # 8 caught
U-Boot Environment: 0x00000000:0x00080000 (NAND)
NAND: ID: dac2 ,256 MiB
MMC: mv_sdh: 0
PCI-e 0: Detected No Link.
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Board configuration detected:
Creating 1 MTD partitions on "nand0":
0x00000f500000-0x00000ff00000 : "mtd=7"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=7"
UBI: MTD device size: 10 MiB
UBI: number of good PEBs: 80
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 48
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 9/4
UBIFS: mounted UBI device 0, volume 0, name "reserve2"
UBIFS: mounted read-only
UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 200807 bytes (196 KiB)
Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)...
Done
Set lan 2 WakeOnLan ok
Enable HD1
Enable HD2
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | In-Band |
| egiga1 | RGMII | In-Band |
| egiga2 | SGMII | 0x00 |
egiga0, egiga1, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv fdt_skip_update yes
Marvell>> setenv initrd_high 0xffffffff
Marvell>> setenv mtdparts 'mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2)'
Marvell>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda2 ${mtdparts} earlyprintk=serial'
Marvell>> setenv ipaddr 192.168.1.110; setenv serverip 192.168.1.23; tftp 0xa00000 boot.p/uImage; tftp 0x1200000 boot.p/uramdisk
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'boot.p/uImage'.
Load address: 0xa00000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################
286.1 KiB/s
done
Bytes transferred = 4525593 (450e19 hex)
Using egiga2 device
TFTP from server 192.168.1.23; our IP address is 192.168.1.110
Filename 'boot.p/uramdisk'.
Load address: 0x1200000
Loading: T T T #################################################################
##############################################
86.9 KiB/s
done
Bytes transferred = 1622632 (18c268 hex)
Marvell>> bootm 0xa00000 0x1200000
## Booting image at 00a00000 ...
## Booting kernel from Legacy Image at 00a00000 ...
Image Name: WDMC-EX2-Ultra
Created: 2022-12-02 11:37:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4525529 Bytes = 4.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01200000 ...
Image Name: Custom initramfs
Created: 2021-07-28 7:11:31 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1622568 Bytes = 1.5 MiB
Load Address: 00e00000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
DTB:0x004540D8 (0x00004D01)
C:0x000080E0-0x00458E80->0x00E7FF00-0x012D0CA0
DTB:0x012CBEF8 (0x00004D9E)
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 6.0.10 (root@virtsrv) (arm-none-eabi-gcc (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027], GNU ld (2.35.2-2+14+b2) 2.35.2) #1 SMP PREEMPT Fri Dec 2 12:12:59 CET 2022
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: My Cloud Expert Series EX2 Ultra (BVBZ/Ranger Peak)
Memory policy: Data cache writealloc
INITRD: 0x01200000+0x0018d000 overlaps in-use memory region
- disabling initrd
Zone ranges:
Normal [mem 0x0000000000000000-0x000000002fffffff]
HighMem [mem 0x0000000030000000-0x000000003fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000000000-0x000000003fffffff]
Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
percpu: Embedded 11 pages/cpu s16212 r8192 d20652 u45056
Built 1 zonelists, mobility grouping on. Total pages: 260416
Kernel command line: console=ttyS0,115200 root=/dev/sda2 ${mtdparts} earlyprintk=serial
Unknown kernel command line parameters "${mtdparts} earlyprintk=serial", will be passed to user space.
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 1024200K/1048576K available (8980K kernel code, 508K rwdata, 2352K rodata, 1024K init, 351K bss, 24376K reserved, 0K cma-reserved, 262144K highmem)
rcu: Preemptible hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
Trampoline variant of Tasks RCU enabled.
Tracing variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 D prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
rcu: srcu_init: Setting srcu_struct sizes based on contention.
sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
Switching to timer-based delay loop, resolution 1ns
Ignoring duplicate/late registration of read_current_timer delay
clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=666000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
CPU: Testing write buffer coherency: ok
CPU0: Spectre v2: using BPIALL workaround
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
cblist_init_generic: Setting adjustable number of callback queues.
cblist_init_generic: Setting shift to 1 and lim to 1.
cblist_init_generic: Setting shift to 1 and lim to 1.
Setting up static identity map for 0x100000 - 0x100060
mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
mvebu-pmsu: Initializing Power Management Service Unit
rcu: Hierarchical SRCU implementation.
rcu: Max phase no-delay instances is 400.
smp: Bringing up secondary CPUs ...
Booting CPU 1
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU1: Spectre v2: using BPIALL workaround
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (2664.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
futex hash table entries: 512 (order: 3, 32768 bytes, linear)
pinctrl core: initialized pinctrl subsystem
NET: Registered PF_NETLINK/PF_ROUTE protocol family
DMA: preallocated 256 KiB pool for atomic coherent allocations
thermal_sys: Registered thermal governor 'step_wise'
mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
cryptd: max_cpu_qlen set to 1000
raid6: neonx8 gen() 587 MB/s
raid6: neonx4 gen() 1677 MB/s
raid6: neonx2 gen() 2047 MB/s
raid6: neonx1 gen() 1705 MB/s
raid6: int32x8 gen() 243 MB/s
raid6: int32x4 gen() 276 MB/s
raid6: int32x2 gen() 440 MB/s
raid6: int32x1 gen() 525 MB/s
raid6: using algorithm neonx2 gen() 2047 MB/s
raid6: .... xor() 1309 MB/s, rmw enabled
raid6: using neon recovery algorithm
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
clocksource: Switched to clocksource arm_global_timer
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
FS-Cache: Loaded
NET: Registered PF_INET protocol family
IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
TCP: Hash tables configured (established 8192 bind 8192)
MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NET: Registered PF_XDP protocol family
PCI: CLS 0 bytes, default 64
workingset: timestamp_bits=14 max_order=18 bucket_order=4
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
Key type cifs.idmap registered
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
xor: measuring software checksum speed
arm4regs : 2166 MB/sec
8regs : 1543 MB/sec
32regs : 1726 MB/sec
neon : 1596 MB/sec
xor: using function: arm4regs (2166 MB/sec)
async_tx: api initialized (async)
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
mv_xor f1060800.xor: Marvell shared XOR driver
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
printk: console [ttyS0] disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 38, base_baud = 12500000) is a 16550A
printk: console [ttyS0] enabled
f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 39, base_baud = 12500000) is a 16550A
brd: module loaded
loop: module loaded
ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
nand: Macronix MX30LF2G18AC
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002020000
nand_read_bbt: bad block at 0x0000062e0000
nand_read_bbt: bad block at 0x00000bac0000
nand_read_bbt: bad block at 0x00000d300000
nand_read_bbt: bad block at 0x00000dc60000
9 fixed-partitions partitions found on MTD device pxa3xx_nand-0
Creating 9 MTD partitions on "pxa3xx_nand-0":
0x000000000000-0x000000500000 : "U-Boot"
0x000000500000-0x000000a00000 : "uImage"
0x000000a00000-0x000000f00000 : "uRamdisk"
0x000000f00000-0x000001400000 : "uImage-old"
0x000001400000-0x000001900000 : "uRamdisk-old"
0x000001900000-0x000001e00000 : "uImage-test"
0x000001e00000-0x000002300000 : "uRamdisk-test"
0x000002300000-0x000002800000 : "reserve2"
0x000002800000-0x00000ff00000 : "storage"
wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
hwmon hwmon0: temp1_input not attached to any thermal zone
mvneta f1034000.ethernet eth0: Using hardware mac address 00:50:43:36:98:34
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-orion: EHCI orion driver
orion-ehci f1058000.usb: EHCI Host Controller
orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
orion-ehci f1058000.usb: irq 42, io mem 0xf1058000
orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 6.0.10 ehci_hcd
usb usb1: SerialNumber: f1058000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
xhci-hcd f10f0000.usb3: irq 43, io mem 0xf10f0000
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 6.0.10 xhci-hcd
usb usb2: SerialNumber: f10f0000.usb3
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 6.0.10 xhci-hcd
usb usb3: SerialNumber: f10f0000.usb3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
xhci-hcd f10f8000.usb3: irq 44, io mem 0xf10f8000
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 6.0.10 xhci-hcd
usb usb4: SerialNumber: f10f8000.usb3
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: xHCI Host Controller
usb usb5: Manufacturer: Linux 6.0.10 xhci-hcd
usb usb5: SerialNumber: f10f8000.usb3
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
i2c_dev: i2c /dev entries driver
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
device-mapper: dm-log-userspace: version 1.3.0 loaded
device-mapper: raid: Loading target version 1.15.1
ledtrig-cpu: registered to indicate activity on CPUs
marvell-cesa f1090000.crypto: CESA device successfully registered
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
NET: Registered PF_INET6 protocol family
Segment Routing with IPv6
In-situ OAM (IOAM) with IPv6
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
NET: Registered PF_PACKET protocol family
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
Registering SWP/SWPB emulation handler
Btrfs loaded, crc32c=crc32c-generic, debug=on, assert=on, ref-verify=on, zoned=no, fsverity=no
BTRFS: selftest: sectorsize: 4096 nodesize: 4096
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
usb 4-1: new high-speed USB device number 2 using xhci-hcd
usb 4-1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 1.00
usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-1: Product: DataTraveler 2.0
usb 4-1: Manufacturer: Kingston
usb 4-1: SerialNumber: 00241D8CE480FE10B97245FE
usb-storage 4-1:1.0: USB Mass Storage device detected
scsi host0: usb-storage 4-1:1.0
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: sectorsize: 4096 nodesize: 8192
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: sectorsize: 4096 nodesize: 16384
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 4
sd 0:0:0:0: [sda] 15131636 512-byte logical blocks: (7.75 GB/7.21 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI removable disk
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: sectorsize: 4096 nodesize: 32768
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: sectorsize: 4096 nodesize: 65536
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: running extent_map tests
BTRFS: selftest: running rmap tests
ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
ahci-mvebu f10a8000.sata: masking port_map 0x3 -> 0x3
ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi host1: ahci-mvebu
scsi host2: ahci-mvebu
ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 47
ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 47
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem
EXT4-fs (sda2): mounted filesystem with ordered data mode. Quota mode: none.
VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
devtmpfs: mounted
Freeing unused kernel image (initmem) memory: 1024K
Run /sbin/init as init process
systemd[1]: System time before build time, advancing clock.
ip_tables: version magic '6.0.10 SMP mod_unload ARMv7 p2v8 ' should be '6.0.10 SMP preempt mod_unload ARMv7 p2v8 '
systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
root@wdmycloud:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00500000 00020000 "U-Boot"
mtd1: 00500000 00020000 "uImage"
mtd2: 00500000 00020000 "uRamdisk"
mtd3: 00500000 00020000 "uImage-old"
mtd4: 00500000 00020000 "uRamdisk-old"
mtd5: 00500000 00020000 "uImage-test"
mtd6: 00500000 00020000 "uRamdisk-test"
mtd7: 00500000 00020000 "reserve2"
mtd8: 0d700000 00020000 "storage"
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 02, 2022 06:35AM |
Registered: 7 months ago Posts: 142 |
I can print the fw envs:
However, since you are helping me, I guess the best would be to work with your uImage, Ramdisk and rootfs
root@wdmycloud:~# fw_printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0x02000020 0x0500000 0x0500000; nand read.e 0x2900000 0x0a00000 0x0500000; bootm 0x02000020 0x2900000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=1 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:36:2c:34 eth1mtu=1500 eth2addr=00:50:43:36:98:34 eth2mtu=1500 eth3addr=00:50:43:2c:98:36 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:98:2c:34 ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:34:98:36 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=1 usbType=3 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81
However, since you are helping me, I guess the best would be to work with your uImage, Ramdisk and rootfs
